| 	
		 ™ 
					GT SERIES   
					Automotive Subwoofers Owner’s Manual GT100 GT100D GT120 GT120D GT150 GT150D   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				Connecting Your Subwoofer to Your Amplifier JBL GT Series   
					Figure 1. Parallel connection   
					To design a subwoofer system   
					that maximizes available amplifier   
					power, keep the following rules   
					in mind:   
					1. The total system impedance   
					of woofers in parallel can be   
					calculated using the formula:   
					JBL GT Series subwoofers   
					2. You may connect the coils of a   
					dual-voice coil woofer in series,   
					but we recommend that you   
					avoid connecting separate   
					are available in two different   
					configurations: as a single 4-ohm   
					voice coil or as dual 4-ohm voice   
					coils. Depending on the amplifiers   
					you are using, you may use either   
					single-voice coil or dual-voice coil   
					subwoofers in singles or multiples   
					to maximize the power available   
					from your amplifiers. To achieve   
					the maximum amplifier output   
					possible, you should design a   
					speaker system that provides   
					the lowest impedance that   
					your amplifier is rated to drive   
					safely. When designing a   
					subwoofer system, consider   
					the following rules:   
					1. Don’t mix different subwoofer   
					or enclosure types in the same   
					system (use all single-coil   
					BLACK   
					RED   
					STRIPE   
					NEG ( – )   
					STRIPE   
					POS ( + )   
					woofers in series. The amplifier-   
					damping factor (the amplifier’s   
					ability to control the motion of   
					the woofer) is expressed as a   
					ratio of terminal impedance   
					(the sum of speaker impedance,   
					wire resistance and the D.C.   
					resistance of any crossover coil   
					connected to the woofer) to   
					amplifier-output impedance.   
					Therefore, connecting separate   
					woofers in series reduces the   
					damping factor of the amplifier   
					to a value less than 1. This will   
					result in poor transient response.   
					3. You must use both coils of a   
					dual-voice coil woofer connected   
					either in series or in parallel.   
					4. Most amplifiers deliver exactly   
					the same amount of power   
					bridged into a 4-ohm load   
					POS ( + )   
					NEG ( – )   
					1 
					1 
					w2   
					Impedance=   
					1 
					w1   
					1 
					w3   
					. . .   
					Figure 2. Series connection   
					+ 
					+ 
					BLACK   
					RED   
					STRIPE   
					NEG ( – )   
					STRIPE   
					POS ( + )   
					where w is the nominal   
					impedance of the woofer.   
					2. The total system impedance   
					of voice coils (or woofers) in   
					series can be calculated using   
					the formula:   
					POS ( + )   
					NEG ( – )   
					Impedance = w1 + w2 + w3 . . .   
					The diagrams at right show parallel   
					and series speaker connections.   
					woofers or all dual-coil woofers).   
					as they do running a 2-ohm   
					stereo load.   
					03   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				Specifications JBL GT Series   
					GT100   
					GT100D   
					10" Dual-voice coil   
					GT120   
					12" Automotive   
					GT120D   
					12" Dual-voice coil   
					automotive subwoofer subwoofer   
					GT150   
					15" Automotive   
					GT150D   
					15" Dual-voice coil   
					automotive subwoofer   
					10" Automotive   
					subwoofer   
					automotive subwoofer subwoofer   
					Power handling (RMS) 250 Watts   
					Power handling (Peak) 1000 Watts   
					250 Watts   
					250 Watts   
					250 Watts   
					250 Watts   
					250 Watts   
					1000 Watts   
					1000 Watts   
					1000 Watts   
					1000 Watts   
					1000 Watts   
					Sensitivity (2.83V/1m)   
					Frequency response   
					90dB   
					90dB   
					93dB   
					93dB   
					95dB   
					95dB   
					28Hz – 500Hz   
					28Hz – 500Hz   
					23Hz – 450Hz   
					23Hz – 450Hz   
					20Hz – 400Hz   
					20Hz – 400Hz   
					Impedance   
					4 Ohms   
					Dual 4-ohm voice coils 4 Ohms   
					Dual 4-ohm voice coils 4 Ohms   
					Dual 4-ohm voice coils   
					6-3/4" (172mm)   
					Mounting depth   
					Cut-out diameter   
					5-3/4" (147mm)   
					9-1/8" (232mm)   
					5-3/4" (147mm)   
					9-1/8" (232mm)   
					6-1/4" (159mm)   
					11-1/8" (283mm)   
					6-1/4" (159mm)   
					11-1/8" (283mm)   
					6-3/4" (172mm)   
					14-1/4" (362mm)   
					14-1/4" (362mm)   
					Declaration of Conformity   
					We, Harman Consumer International   
					2, route de Tours   
					72500 Chateau-du-Loir   
					FRANCE   
					JBL Consumer Products • 250 Crossways Park Drive, Woodbury, NY 11797   
					
					Features, specifications and appearance are subject to change without notice.   
					declare in own responsibility, that the products described in this owner’s manual are in   
					compliance with technical standards:   
					©2002 JBL, Incorporated • JBL is a registered trademark of JBL, Incorporated   
					Part No. GTSUBSEROM   
					EN 50081-1:1992   
					EN 50082-1:1997   
					Emmanuel Millot   
					Harman Consumer International   
					Chateau-du-Loir, FRANCE. 7/02   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				 | 
Indesit Washer Dryer PWDE 8148 S User Manual
InFocus Projector XS1 User Manual
JBL Home Theater System L830 User Manual
Jet Tools Film Camera JTM 4VS User Manual
JVC CD Player ADV5580 User Manual
JVC Stereo Receiver LVT0014 001A User Manual
JVC Stereo System UX L5V User Manual
JVC VCR LPT0641 001A User Manual
King Canada Washer KPW 205 User Manual
Kodak Projector VIDEOMATE 2030 User Manual