80C51FA/83C51FA
EVENT-CONTROL CHMOS SINGLE-CHIP
8-BIT MICROCONTROLLER
Automotive
Y
Y
Extended Automotive
Temperature Range
Programmable Serial Channel with:
- Framing Error Detection
- Automatic Address Recognition
b
a
(
40 C to 125 C Ambient)
§
§
Y
Y
Y
High Performance CHMOS Process
TTL and CMOS Compatible Logic
Levels
Three 16-Bit Timer/Counters
- Timer 2 is an Up/Down
Timer/Counter
Y
Y
Y
64K External Program Memory Space
64K External Data Memory Space
Y
Programmable Counter Array with:
- High Speed Output
- Compare/Capture
- Pulse Width Modulator
- Watchdog Timer Capabilities
MCS 51 Microcontroller Fully
É
Compatible Instruction Set
Y
Power Saving Idle and Power Down
Modes
Y
Y
ONCE (On-Circuit Emulation) Mode
Available in PLCC and PDIP Packages
Y
Y
Y
Y
Y
8K On-Chip ROM
256 Bytes of On-Chip Data RAM
Boolean Processor
Ý
(See Packaging Specification, Order 231369)
Y
Available in 12 MHz and 16 MHz
Versions
32 Programmable I/O Lines
7 Interrupt Sources
MEMORY ORGANIZATION
PROGRAM MEMORY: Up to 8 Kbytes of the program memory can reside in the on-chip ROM. In addition the
device can address up to 64K of program memory external to the chip.
DATA MEMORY: This microcontroller has a 256 x 8 on-chip RAM. In addition it can address up to 64 Kbytes of
external data memory.
The Intel 80C51FA/83C51FA is a single-chip control oriented microcontroller which is fabricated on Intel's
CHMOS III (83C51FA) ROM technology. For the remainder of this datasheet references to the ROMless
(80C51FA) and ROM (83C51FA) versions will be denoted as 83C51FA. Being a member of the MCS 51
É
microcontroller family, the 83C51FA uses the same powerful instruction set, has the same architecture, and is
pin-for-pin compatible with the existing MCS 51 microcontroller products. The 83C51FA is an enhanced
version of the 87C51. It's added features make it an even more powerful microcontroller for applications that
require Pulse Width Modulation, High Speed I/O, and up/down counting capabilities such as brake and
traction control. It also has a more versatile serial channel that facilitates multi-processor communications.
NOTICE:
This datasheet contains information on products in full production. Specifications within this datasheet
are subject to change without notice. Verify with your local Intel sales office that you have the latest
datasheet before finalizing a design.
*Other brands and names are the property of their respective owners.
Information in this document is provided in connection with Intel products. Intel assumes no liability whatsoever, including infringement of any patent or
copyright, for sale and use of Intel products except as provided in Intel's Terms and Conditions of Sale for such products. Intel retains the right to make
changes to these specifications at any time, without notice. Microcomputer Products may have minor variations to this specification known as errata.
COPYRIGHT ©INTEL CORPORATION, 2004
June 2004
Order Number: 270501-008
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
temperature range of 0 C to 70 C ambient. With the
extended temperature range option, operational
characteristics are guaranteed over the temperature
°
°
80C51FA/83C51FA PRODUCT
OPTIONS
range of
ambient. For the automo-
-40 °C to + 85°C
Intel’s extended and automotive temperature range
products are designed to meet the needs of those
applications whose operating requirements exceed
commercial standards.
tive temperature range option, operational charac-
teristics are guaranteed over the temperature range
of -40°C to +125°C ambient.
As shown in Figure 2 temperature, burn-in, and
package options are identified by a one- or two-letter
prefix to the part number.
With the commercial standard temperature range,
operational characteristics are guaranteed over the
x
x
x
270501–2
Figure 2. MCS® 51 Microcontroller Product Family Nomenclature
Table 1. Temperature Options
Operating
Temperature
Classification
Temperature
Designation
Burn-In
Options
Temperature
C Ambient
°
-
-
+
Extended
T
L
40 to 85
Standard
Extended
+
40 to 85
-
-
+
Automotive
A
B
40 to 125
Standard
Extended
+
40 to 125
3
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
PIN DESCRIPTIONS
Port Pin
Alternate Function
V
: Supply voltage.
CC
P1.0
T2 (External Count Input to Timer/
Counter 2)
V
: Circuit ground.
SS
P1.1
T2EX (Timer/Counter 2 Capture/
Reload Trigger and Direction Control)
Port 0: Port 0 is an 8-bit, open drain, bidirectional
I/O port. As an output port each pin can sink several
LS TTL inputs. Port 0 pins that have 1's written to
them float, and in that state can be used as high-im-
pedance inputs.
P1.2
P1.3
ECI (External Count Input to the PCA)
CEX0 (External I/O for Compare/
Capture Module 0)
P1.4
P1.5
P1.6
P1.7
CEX1 (External I/O for Compare/
Capture Module 1)
Port 0 is also the multiplexed low-order address and
data bus during accesses to external Program and
Data Memory. In this application it uses strong inter-
nal pullups when emitting1's, and can source and
sink several LS TTL inputs.
CEX2 (External I/O for Compare/
Capture Module 2)
CEX3 (External I/O for Compare/
Capture Module 3)
CEX4 (External I/O for Compare/
Capture Module 4)
Port 0 outputs the code bytes during program verifi-
cation. External pullup resistors are required during
program verification.
Port 2: Port 2 is an 8-bit bidirectional I/O port with
internal pullups. The Port 2 output buffers can drive
LS TTL inputs. Port 2 pins that have 1's written to
them are pulled high by the internal pullups, and in
that state can be used as inputs. As inputs, Port 2
pins that are externally pulled low will source current
Port 1: Port 1 is an 8-bit bidirectional I/O port with
internal pullups. The Port 1 output buffers can drive
LS TTL inputs. Port 1 pins that have 1's written to
them are pulled high by the internal pullups, and in
that state can be used as inputs. As inputs, Port 1
pins that are externally pulled low will source current
(I , on the datasheet) because of the internal pull-
IL
ups.
(I , on the datasheet) because of the internal pull-
IL
ups.
Port 2 emits the high-order address byte during
fetches from external Program Memory and during
accesses to external Data Memory that use 16-bit
addresses (MOVX @DPTR). In this application it
uses strong internal pullups when emitting 1's. Dur-
ing accesses to external Data Memory that use 8-bit
In addition, Port 1 serves the functions of the follow-
ing special features of the 83C51FA:
Pin (PDIP)
Pad (PLCC)
270501±3
270501±4
**Do not connect reserved pins.
Diagrams are for pin reference only. Package sizes are not to scale.
Figure 3. Pin Connections
4
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
addresses (MOVX @Ri), Port 2 emits the contents of
the P2 Special Function Register.
EA/V : External Access enable. EA must be
PP
strapped to V
in order to enable the device to
SS
fetch code from external Program Memory locations
0000H to 0FFFFH. Note, however, that if either of
the Program Lock bits are programmed, EA will be
internally latched on reset.
Port 3: Port 3 is an 8-bit bidirectional I/O port with
internal pullups. The Port 3 output buffers can drive
LS TTL inputs. Port 3 pins that have 1's written to
them are pulled high by the internal pullups, and in
that state can be used as inputs. As inputs, Port 3
pins that are externally pulled low will source current
EA should be strapped to V
executions.
for internal program
CC
(I , on the datasheet) because of the pullups.
IL
XTAL1: Input to the inverting oscillator amplifier.
Port 3 also serves the functions of various special
features of the MCS 51 microcontroller family, as
listed below:
XTAL2: Output from the inverting oscillator amplifi-
er.
Port Pin
Alternate Function
RXD (serial input port)
TXD (serial output port)
INT0 (external interrupt 0)
INT1 (external interrupt 1)
T0 (Timer 0 external input)
T1 (Timer 1 external input)
WR (external data memory write strobe)
RD (external data memory read strobe)
OSCILLATOR CHARACTERISTICS
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
XTAL1 and XTAL2 are the input and output, respec-
tively, of a inverting amplifier which can be config-
ured for use as an on-chip oscillator, as shown in
Figure 4. Either a quartz crystal or ceramic resonator
may be used. More detailed information concerning
the use of the on-chip oscillator is available in Appli-
cation Note AP-155, ``Oscillators for Microcontrol-
lers.''
To drive the device from an external clock source,
XTAL1 should be driven, while XTAL2 floats, as
shown in Figure 5. There are no requirements on the
duty cycle of the external clock signal, since the in-
put to the internal clocking circuitry is through a di-
vide-by-two flip-flop, but minimum and maximum
high and low times specified on the datasheet must
be observed.
RESET: Reset input. A high on this pin for two ma-
chine cycles while the oscillator is running resets the
device. An internal pulldown resistor permits a pow-
er-on reset with only a capacitor connected to V
.
CC
ALE/PROG : Address Latch Enable output pulse for
latching the low byte of the address during accesses
to external memory.
An external oscillator may encounter as much as a
100 pF load at XTAL1 when it starts up. This is due
to interaction between the amplifier and its feedback
In normal operation ALE is emitted at a constant
rate of (/6 the oscillator frequency, and may be used
for external timing or clocking purposes. Note, how-
ever, that one ALE pulse is skipped during each ac-
cess to external Data Memory.
capacitance. Once the external signal meets the V
IL
and V specifications the capacitance will not ex-
IH
ceed 20 pF.
Throughout the remainder of this datasheet, ALE will
refer to the signal coming out of the ALE/PROG pin,
and the pin will be referred to as the ALE/PROG pin.
PSEN: Program Store Enable is the read strobe to
external Program Memory.
When the 83C51FA is executing code from external
Program Memory, PSEN is activated twice each ma-
chine cycle, except that two PSEN activations are
skipped during each access to external Data Memo-
ry.
270501±5
e
g
C1, C2
30 pF 10 pF for Crystals
For Ceramic Resonators, contact resonator manufacturer.
Figure 4. Oscillator Connections
5
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
restored to its normal operating level and must be
held active long enough for the oscillator to restart
and stabilize (normally less than 10 ms).
With an external interrupt, INT0 or INT1 must be en-
abled and configured as level-sensitive. Holding the
pin low restarts the oscillator but bringing the pin
back high completes the exit. Once the interrupt is
serviced, the next instruction to be executed after
RETI will be the one following the instruction that put
the device into Power Down.
270501±6
Figure 5. External Clock Drive Configuration
DESIGN CONSIDERATION
IDLE MODE
When the Idle mode is terminated by a hardware
reset, the device normally resumes program execu-
tion, from where it left off, up to two machine cycles
before the internal reset algorithm takes control. On-
chip hardware inhibits access to internal RAM in this
event, but access to the port pins is not inhibited. To
eliminate the possibility of an unexpected write when
Idle is terminated by reset, the instruction following
the one that invokes Idle should not be one that
writes to a port pin or to external memory.
The user's software can invoke the Idle Mode. When
the microcontroller is in this mode, power consump-
tion is reduced. The Special Function Registers and
the onboard RAM retain their values during Idle, but
the processor stops executing instructions. Idle
Mode will be exited if the chip is reset or if an en-
abled interrupt occurs. The PCA timer/counter can
optionally be left running or paused during Idle
Mode.
ONCE MODE
POWER DOWN MODE
The ONCE (``On-CircuitEmulation'') Mode facilitates
testing and debugging of systems using the
83C51FA without the 83C51FA having to be re-
moved from the circuit. The ONCE Mode is invoked
by:
To save even more power, a Power Down mode can
be invoked by software. In this mode, the oscillator
is stopped and the instruction that invoked Power
Down is the last instruction executed. The on-chip
RAM and Special Function Registers retain their val-
ues if the Power Down mode is terminated with an
interrupt.
1) Pull ALE low while the device is in reset and
PSEN is high;
2) Hold ALE low as RST is deactivated.
On the 83C51FA either a hardware reset or external
interrupt can cause an exit from Power Down. Reset
redefines all the SFRs but does not change the on-
chip RAM. An external interrupt allows both the
SFRs and the on-chip RAM to retain their values.
While the device is in ONCE Mode, the Port 0 pins
float, the other port pins and ALE and PSEN are
weakly pulled high. The oscillator circuit remains ac-
tive. While the 83C51FA is in this mode, an emulator
or test CPU can be used to drive the circuit. Normal
operation is restored when a normal reset is applied.
To properly terminate Power Down the reset or ex-
ternal interrupt should not be executed before V is
CC
Table 2. Status of the External Pins during Idle and Power Down
Program
Memory
Mode
Idle
ALE
PSEN
PORT0
PORT1
PORT2
PORT3
Internal
External
Internal
External
1
1
0
0
1
1
0
0
Data
Float
Data
Float
Data
Data
Data
Data
Data
Address
Data
Data
Data
Data
Data
Idle
Power Down
Power Down
Data
NOTE:
For more detailed information on the reduced power modes refer to current Embedded Applications Handbook, and Applica-
tion Note AP-252, ``Designingwith the 80C51BH.''
6
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
ABSOLUTE MAXIMUM RATINGS*
NOTICE: This is a production data sheet. The specifi-
cations are subject to change without notice.
Ambient Temperature
Under Bias...................................-40°C to +125°C
*WARNING: Stressing the device beyond the ``Absolute
Maximum Ratings'' may cause permanent damage.
These are stress ratings only. Operation beyond the
``Operating Conditions'' is not recommended and ex-
tended exposure beyond the ``Operating Conditions''
may affect device reliability.
Storage Temperature.......................-65°C to +150°C
Voltage on Any Other Pin to V
SS........-0.5V to +6.5V
I
I/O Pin........................................................15mA
OL
Power Dissipation
(Based on PACKAGE heat transfer limitations, not
device power consumption)
Typical Junction Temperature (T )................+135°C
J
a
(Based upon Ambient Temperature at 125 C)
§
Typical Thermal Resistance
Junction-to-Ambient (i
)
JA
PDIP.......................................................45°C/W
PLCC......................................................46°C/W
e b
a
e
e
g
DC CHARACTERISTICS: (T
40 C to 125 C; V
5V 10%; V
0V)
§
§
A
CC
SS
Symbol
Parameter
Input Low Voltage
Input Low Voltage EA
Input High Voltage
Min
Typ
Max
Unit
Test Conditions
b
0.5
0
b
b
V
V
V
0.2 V
0.2 V
0.1
0.3
V
V
V
IL
CC
CC
IL1
IH
a
a
0.2 V
0.9
V
0.5
CC
CC
(Except XTAL2, RST, EA)
a
V
V
V
Input High Voltage
(XTAL, RST)
0.7 V
V
0.5
V
V
V
IH1
OL
CC
CC
(1)
e
Output Low Voltage
(Ports 1, 2 and 3)
0.45
0.45
I
1.6 mA
OL
e
e
e
Output Low Voltage
I
20
3.2 mA
7.0 mA
OL1
OL
(1)
(Port 0, ALE/PROG, PSEN)
I
OL
I
OL
e b
60 mA
V
Output High Voltage
(Ports 1, 2 and 3
ALE/PROG and PSEN)
2.4
0.9 V
V
I
OH
OH
(2)
e b
e b
e b
V
V
I
10 mA
CC
OH
V
OH1
Output High Voltage
2.4
0.9 V
I
OH
800 mA
(2)
(Port 0 in External Bus Mode)
V
I
80 mA
CC
OH
b
b
g
e
I
I
Logical 0 Input Current
(Ports 1, 2 and 3)
10
50
10
mA
V
0.45V
IL
IN
e
Input leakage Current
(Port 0)
0.02
mA
V
IN
V
IL
or V
LI
IH
7
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
e b
a
e
e
g
DC CHARACTERISTICS: (T
40 C to 125 C; V
5V 10%; V
0V) (Continued)
§
§
A
CC
SS
Symbol
Parameter
Min
Typ
Max
Unit Test Conditions
b
b
e
I
TL
Logical 1 to 0 Transition Current
(Ports 1, 2, and 3)
265
650
mA
V
IN
2V
RRST
CIO
RST Pulldown Resistor
Pin Capacitance
40
100
10
225
KX
pF
@1MHz, 25 C
§
I
Power Supply Current:
(Note 3)
CC
Running at 12 MHz (Figure 5)
Idle Mode at 12 MHz (Figure 5)
40
15
150
mA
mA
mA
Power Down Mode (I
)
PD
NOTES:
1. Capacitive loading on Ports 0 and 2 may cause noise pulses to be superimposed on the V s of ALE and Ports 1 and 3.
OL
The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0
transitions during bus operations. In applications where capacitance loading exceeds 100 pFs, the noise pulse on the ALE
signal may exceed 0.8V. In these cases, it may be desirable to qualify ALE with a Schmitt Trigger, or use an Address Latch
with a Schmitt Trigger Strobe input.
2. Capacitive loading on Ports 0 and 2 cause the V
address lines are stabilizing.
on ALE and PSEN to drop below the 0.9 V specification when the
OH
CC
3. See Figures 6±9 for test conditions. Minimum V
for Power Down is 2.0V.
CC
4. Typicals are based on limited number of samples, and are not guaranteed. The values listed are at room temperature and
5.0V.
5. Under steady state (non-transient) conditions, I must be externally limited as follows:
OL
10 mA
Maximum I per Port Pin:
OL
Maximum I per 8-Bit Port -
OL
Port 0:
Ports 1, 2, and 3:
Maximum Total I for all Output Pins:
26 mA
15 mA
71 mA
OL
If I exceeds the test condition, V may exceed the related specification. Pins are not guaranteed to sink current greater
OL
OL
than the listed test conditions.
6. Contact Intel for design-in information.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
270501±7
I
Max at other frequencies is given by:
CC
Active Mode
I
270501±8
e
c
a
e
e
Max
(3
Osc Freq)
4
TCLCH
TCHCL
5 ns
CC
Idle Mode
Max
e
c
a
I
(0.49
Osc Freq)
1.6
CC
Figure 7. I Test Condition, Active Mode
CC
Where Osc Freq is in MHz, I
is in mA.
CC
All other pins disconnected.
Figure 6. I vs Frequency
CC
270501±10
Figure 9. I Test Condition,
CC
270501±9
Power Down Mode.
e
e
TCLCH
TCHCL
5 ns
All other pins disconnected.
Figure 8. I Test Condition Idle Mode.
CC
e
V
2.0V to 5.5V.
CC
All other pins disconnected.
270501±11
e
e
Figure 10. Clock Signal Waveform for I Tests in Active and Idle Modes. TCLCH
TCHCL
5 ns.
CC
9
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
L: Logic level LOW, or ALE
P: PSEN
EXPLANATION OF THE AC SYMBOLS
Q: Output Data
R: RD signal
T: Time
Each timing symbol has 5 characters. The first char-
acter is always a `T' (stands for time). The other
characters, depending on their positions, stand for
the name of a signal or the logical status of that
signal. The following is a list of all the characters and
what they stand for.
V: Valid
W: WR signal
X: No longer a valid logic level
Z: Float
A: Address
C: Clock
For example,
D: Input Data
H: Logic level HIGH
I: Instruction (program memory contents)
e
e
T
AVLL
T
LLPL
Time from Address Valid to ALE Low
Time from ALE Low to PSEN Low
e b
a
e
e
g
AC CHARACTERISTICS (T
40 C to 125 C, V
5V 10%, V
0V, Load Capacitance
e
80 pF)
§
§
A
e
CC
SS
for Port 0, ALE/PROG and PSEN 100 pF, Load Capacitance for All Other Outputs
EXTERNAL MEMORY CHARACTERISTICS
12 MHz Oscillator
Variable Oscillator
Symbol
Parameter
Units
Min
Max
Min
Max
1/T
Oscillator Frequency
3.5
16
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
CLCL
b
40
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
ALE Pulse Width
127
43
2T
LHLL
CLCL
b
40
Address Valid to ALE Low
Address Hold After ALE Low
ALE Low to Valid Instruction In
ALE Low to PSEN Low
T
T
AVLL
LLAX
LLIV
CLCL
CLCL
b
53
30
b
224
135
4T
3T
110
115
CLCL
b
53
T
30
LLPL
CLCL
b
45
PSEN Pulse Width
205
3T
PLPH
PLIV
CLCL
b
PSEN Low to Valid Instruction In
Input Instr Hold After PSEN Trans
Input Instr Float After PSEN Trans
Address to Valid Instruction In
PSEN Low to Address Float
RD Pulse Width
CLCL
0
0
PXIX
b
b
59
302
10
T
25
PXIZ
CLCL
5T
115
AVIV
CLCL
10
PLAZ
RLRH
WLWH
RLDV
RHDX
RHDZ
LLDV
AVDV
LLWL
AVWL
QVWX
WHQX
QVWH
RLAZ
WHLH
b
b
400
400
6T
6T
100
100
CLCL
WR Pulse Width
CLCL
b
RD Low to Valid Data In
Data Hold After RD High
Data Float After RD High
ALE Low to Valid Data In
Address Valid to Valid Data In
ALE Low to RD or WR Low
Data Valid to WR Low
242
5T
175
CLCL
b
b
10
10
b
107
507
575
300
2T
60
CLCL
b
8T
9T
160
175
CLCL
CLCL
b
b
a
50
200
203
23
3T
50
130
50
3T
CLCL
CLCL
b
4T
T
CLCL
CLCL
CLCL
CLCL
b
b
b
Address Valid before WR Low
Data Hold after WR High
Data Valid to WE High
33
T
50
433
7T
150
RD Low to Address Float
RD or WR High to ALE High
0
0
b
a
40
43
123
T
40
T
CLCL
CLCL
10
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
EXTERNAL PROGRAM MEMORY READ CYCLE
270501±12
EXTERNAL DATA MEMORY READ CYCLE
270501±13
EXTERNAL DATA MEMORY WRITE CYCLE
270501±14
11
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
SERIAL PORT TIMING-SHIFT REGISTER MODE
e b
a
e
e
e
g
Test Conditions:
T
A
40 C to 125 C; V
5V 10%; V
0V; Load Capacitance
Variable Oscillator
Min Max
80 pF
§
§
CC
SS
12 MHz Oscillator
Symbol
Parameter
Units
Min
1
Max
T
T
Serial Port Clock Cycle Time
12T
ms
XLXL
CLCL
b
CLCL
Output Data Setup to Clock
Rising Edge
700
10T
133
ns
QVXH
b
T
XHQX
T
XHDX
T
XHDV
Output Data Hold after
Clock Rising Edge
50
0
2T
117
ns
ns
ns
CLCL
Input Data Hold After Clock
Rising Edge
0
b
133
Clock Rising Edge to Input
Data Valid
700
10T
CLCL
SHIFT REGISTER MODE TIMING WAVEFORMS
270501±15
EXTERNAL CLOCK DRIVE
Symbol
Parameter
Oscillator Frequency
High Time
Min
3.5
20
Max
Units
MHz
ns
1/T
16
CLCL
CHCX
T
T
T
T
Low Time
20
ns
CLCX
CLCH
CHCL
Rise Time
20
20
ns
Fall Time
ns
EXTERNAL CLOCK DRIVE WAVEFORM
270501±16
12
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMOTIVE 80C51FA/83C51FA
AC TESTING INPUT, OUTPUT WAVEFORMS
FLOAT WAVEFORMS
270501±18
For timing purposes a port pin is no longer floating when a
100 mV change from load voltage occurs, and begins to float
270501±17
b
AC Inputs during testing are driven at V
0.5V for a Logic ``1''
and 0.45V for a Logic ``0''. Timing measurements are made at V
CC
IH
when a 100 mV change from the loaded V /V
level occurs.
OH OL
min for a Logic ``1'' and V max for a Logic ``0''.
t
OL
g
I
/I
20 mA. This is for Ports 1, 2 and 3.
OL OH
DATASHEET REVISION HISTORY
The following are key differences between this datasheet and the -007 version:
1. Product prefix variables are now indicated with an x.
The following are key differences between this datasheet and the -006 version:
1. The ``preliminary'' status was dropped and replaced with production status (no label).
2. Trademarks were updated.
The following are key differences between the -006 and the -005 version of the datasheet:
1. Preliminary notice has been added to the Title page.
2. Figure 3 Pin Connections has been modified, RST pin is now RESET pin.
3. RST pin description is now RESET pin description.
4. Figure 6 I vs. Frequency has been corrected to show test conditions.
CC
5. I Max spec has been corrected.
CC
6. A.C. Characteristic table 1/T
spec has been changed to have a Max frequency of 16 MHz.
CLCL
The following are key differences between the -005 and the -004 version of the datasheet:
1. ``NC'' pin labels changed to ``Reserved'' in Figure 3.
2. Capacitor value for ceramic resonators deleted in Figure 4.
The following are the key differences between the -003 version of the 8XC51FA datasheet and the -004
version of the 80C51FA/83C51FA datasheet:
1. Removed references to EPROM from the 8XC51FA datasheet.
2. Revised Figure 4, ``Oscillator Connections''.
The following are the key differences between the -002 and the -003 version of this datasheet:
1. Dropped word ``maximum'' from I in the Absolute Maximum Rating table.
OL
2. Dropped EA from I specification of the DC table.
LI
3. Corrected TQVWH specification (from TTCLCL -70 to TCLCL -150).
4. Added note on external clock capacitance loading.
5. Changed the title to 80C51FA/83C51FA Event-Control CHMOS Single-Chip 8-Bit Microcontroller.
6. Added pin count to Figure 1.
g
7. Changed I to 10 μA.
LI
8. Added I Power Down Mode 150 nA.
CC
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|