Quick Setup Guide
MFC-790CW
MFC-990CW
Start Here
Before you can use the machine, read this Quick Setup Guide for the correct setup and installation.
Warnings tell you what to do to prevent possible personal injury.
WARNING
Important
DO NOT connect the USB cable yet (if you are using a USB
cable).
Unpack the machine and check the components
1
Black
Yellow
Cyan
2
Magenta
StarterInkCartridges
[x4]
Quick Setup Guide
User’s Guide
CD-ROM
Accessory Order Form
Cordless Handset
Test Sheet (USA only)
Telephone Line Cord
TelephoneHandset
(MFC-790CW only) (MFC-790CW only) (MFC-990CW only)
Side Cover
Battery and Battery Cover
(MFC-990CW only)
User’s Guidefor Cordless Handset
(MFC-990CW only)
WARNING
Plastic bags are used in the packaging of your machine. To avoid danger of suffocation, please keep
these bags away from babies and children.
„ Illustrations in this Quick Setup Guide are based on MFC-790CW.
a
Remove the protective tape and film covering the scanner glass.
b
c
d
Remove the green protective packing a by lifting the front of the
machine and then pulling down on the packing part.
Remove the plastic bag
the paper tray.
b
containing the ink cartridges from on top of
Make sure you have all components.
1
USA/CAN Version 0
1
d
e
Fan the stack of paper well to avoid paper jams
and misfeeds.
g
Close the paper tray cover a.
1
Gently put the paper into the paper tray print
side down and top edge first. Check that the
paper is flat in the tray.
Important
Do not push the paper in too far.
h
i
Slowly push the paper tray completely into the
machine.
Note
When you use Legal size paper, press and hold
the universal guide release button a as you slide
out the front of the paper tray.
While holding the paper tray in place, pull out
the paper support a until it clicks, and then
unfold the paper support flap b.
2
1
1
f
Gently adjust the paper side guides to the
paper with both hands. Make sure that the
paper side guides touch the edges of the
paper.
3
Note
Connect the power cord
and telephone line
If you are sharing one telephone line with an
external telephone, connect it as shown below.
4
Before you connect the external telephone,
remove the protective cap a from the EXT. jack
on the machine.
Important
DO NOT connect the USB cable yet (if you are
using a USB cable).
1
a
Connect the power cord.
2
1
b
Connect the telephone line cord. Connect one
end of the telephone line cord to the jack on the
machine marked LINE and the other end to a
modular wall jack.
1 Extension telephone
2 External telephone
Note
If you are sharing one telephone line with an
external telephone answering machine, connect it
as shown below.
Before you connect the external telephone
answering machine, remove the protective cap a
from the EXT. jack on the machine.
Important
The telephone line cord MUST be connected
to the jack on the machine marked LINE.
1
Set the receive mode to Manualif you have
an external answering machine. See Choose
additional details, see Connecting an external
TAD (telephone answering device) in Chapter
7 of the User’s Guide.
4
e
Turn the green knob on the protective yellow
cap clockwise to release the vacuum seal, then
remove the cap a.
Install the ink cartridges
5
WARNING
If ink gets in your eyes, wash them out with
water at once, and if irritation occurs consult a
doctor.
a
b
Make sure that the power is turned on.
The LCD shows:
No Cartridge
Install Ink
1
BK
Y
Black
Cyan
Yellow
Magenta
C
M
Open the ink cartridge cover a.
f
Take care to match the color of the lever a
with the cartridge color b, as shown in the
diagram below.
1
1
c
Remove the green protective part a.
2
1
g
Install each ink cartridge in the direction of the
arrow on the label.
Note
Do not throw away the green protective part.
You will need it if you transport the machine.
d
Unpack the ink cartridge.
5
h
Gently push the ink cartridge until it clicks. After
all the ink cartridges are installed close the ink
cartridge cover.
Important
• DO NOT take out ink cartridges if you do not
need to replace them. If you do so, it may
reduce the ink quantity and the machine will
not know the quantity of ink left in the
cartridge.
• DO NOT shake the ink cartridges. If ink
stains your skin or clothing, wash with soap
or detergent at once.
• DO NOT repeatedly insert and remove the
cartridges. If you do so, ink may seep out of
the cartridge.
• If you mix the colors by installing an ink
cartridge in the wrong position, clean the
print head several times after correcting the
cartridge installation. (See Cleaning the
print head in Appendix B of the User’s
Guide.)
Note
The machine will prepare the ink tube system for
printing. This process will take approximately four
minutes. Do not turn off the machine.
• Once you open an ink cartridge, install it in
the machine and use it up within six months
of installation. Use unopened ink cartridges
by the expiration date written on the
cartridge package.
• DO NOT dismantle or tamper with the ink
cartridge, this can cause the ink to leak out
of the cartridge.
• Brother strongly recommends that you do
not refill the ink cartridges provided with
your machine. We also strongly recommend
that you continue to use only Genuine
Brother Brand replacement ink cartridges.
Using or attempting to use potentially
incompatible inks and/or cartridges in your
machine may cause damage to the machine
itself and/or it may result in unsatisfactory
print quality. Our warranty coverage does
not apply to any problem that was caused by
the use of unauthorized third party ink
and/or cartridges. To protect your
investment and guarantee your print quality
please continue to replace consumed ink
cartridges with only Genuine Brother
Branded Supplies.
6
d
The LCD asks you if the print quality is OK for
black and color. Press Yesor No.
Check the print quality
6
Black OK?
a
When the preparation process has finished, the
LCD shows this message
Yes
No
.
Set Paper and Press Start
After pressing Yesor Nofor both black and
color, the LCD shows:
Start Cleaning?
Press Start
Press Color Start.
b
c
Check the quality of the four color blocks a on
the sheet. (black/yellow/cyan/magenta)
e
f
Press Color Start, the machine will then start
cleaning the colors.
1
After cleaning is finished, press Color Start.
The machine starts printing the Print Quality
If all lines are clear and visible, press Yesto
finish the quality check.
Choose your language
(If needed)
OK
7
a
b
c
d
e
f
Press MENU.
Press a or b to display Initial Setup.
Press Initial Setup.
Press a or b to display Local Language.
Press Local Language.
Press your language.
If you can see missing short lines, press Noand
Poor
g
Press Stop/Exit.
7
Choose the correct Receive Mode
8
The correct Receive Mode is determined by the external devices and telephone subscriber services (Voice Mail,
Distinctive Ring, etc.) you have (or will be using) on the same line as the Brother machine.
Will you be using a Distinctive Ring number for receiving faxes?
Brother uses the term "Distinctive Ring" but telephone companies may have other names for this service such
as Custom Ringing, RingMaster, Personalized Ring, Teen Ring, Ident-A-Call, and Smart Ring. See Distinctive
Ring in Chapter 7 of the User's Guide for instruction on setting up your machine using this feature.
Will you be using Voicemail on the same telephone line as your Brother machine?
If you have Voice Mail on the same telephone line as your Brother machine, there is a strong possibility that
Voice Mail and the Brother machine will conflict with each other when receiving incoming calls. See Voice Mail
in Chapter 7 of the User's Guide for instructions on setting up your machine using this service.
Will you be using the Built in Message Center?
Your Brother machine has a built-in digital Message Center that allows you to store incoming voice or fax
messages. See the next step "Setting up the Message Center".
Will you be using a Telephone Answering Device on the same telephone line as your Brother machine?
Your external telephone answering device (TAD) will automatically answer every call. Voice messages are stored on
the external TAD and fax messages are printed. Choose Manualas your receive mode. See the instructions below.
Will you be using your Brother machine on a dedicated fax line?
Your machine automatically answers every call as a fax. Choose Fax Onlyas your receive mode. See the
instructions below.
Will you be using your Brother machine on the same line as your telephone?
Do you want to receive voice calls and faxes automatically?
The Fax/Telreceive mode is used when sharing the Brother machine and your telephone on the same
line. Choose Fax/Telas your receive mode. See the instructions below.
Important Note: You cannot receive voice messages on either Voice Mail or an answering machine
when choosing the Fax/Telmode.
Do you expect to receive very few faxes?
Choose Manualas your receive mode. You control the phone line and must answer every call yourself.
See the instructions below.
For details, see Using receive modes in Chapter 6 of the User's Guide.
a
b
c
d
e
f
Press MENU.
Press a or b to display Initial Setup.
Press Initial Setup.
Press Receive Mode.
Press Fax Only, Fax/Telor Manual.
Press Stop/Exit.
8
Setting up the Message
Center
Set the LCD contrast
(If needed)
9
10
You must record an outgoing message in order to use
the Message Center mode.
If you are having difficulty reading the LCD, try
changing the contrast setting.
a
Record the Message Center outgoing
message (Msg Ctr OGM).
a
b
c
d
e
f
Press MENU.
Press a or b to display General Setup.
Press General Setup.
Press a or b to display LCD Settings.
Press LCD Settings.
See Outgoing message (OGM) in Chapter 9
of the User’s Guide.
b
Activate Message Center mode.
Press
. The button will light when the mode
is active.
Press LCD Contrast.
g
h
Press Light, Medor Dark.
Press Stop/Exit.
If the Message Center Mode is on, it
overrides your Receive Mode setting. The
built-in digital Message Center answers
voice calls. If the call is a fax, you can
receive a fax automatically. For details, see
Message Center in Chapter 9 of the User’s
Guide.
Note
You can also adjust the angle of the display by
lifting it.
9
i
Press Stop/Exit.
Set the date and time
To confirm the current date and time, print
out the User Settings report. (See Printing
Reports in Chapter 10 of the User's Guide.)
11
The machine displays the time, and if you set up the
station ID the date and time will be added to each fax
you send.
a
b
c
d
e
Press MENU.
Press a or b to display Initial Setup.
Press Initial Setup.
Press Date&Time.
Enter the last two digits of the year on the
Touchscreen, and then press OK.
Date&Time
Year::2008
(e.g. Enter 08for 2008.)
f
Enter the two digits for the month on the
Touchscreen, and then press OK.
Date&Time
Month:03
(e.g. Enter 03for March.)
g
h
Enter the two digits for the day on the
Touchscreen, and then press OK.
Date&Time
Day:01
(e.g. Enter 01for the first day of the month.)
Enter the time in 24-hour format on the
Touchscreen, and then press OK.
Date&Time
Time:15:25
(e.g. Enter 15, 25for 3:25 P.M.)
10
Set your station ID
Set tone or pulse dialing
mode
12
13
You should store your name and fax number to be
printed on all fax pages that you send.
Your machine comes set for Tone dialing service. If
you have Pulse dialing service (rotary), you need to
change the dialing mode.
a
b
c
d
e
Press MENU.
a
b
c
d
e
f
Press MENU.
Press a or b to display Initial Setup.
Press Initial Setup.
Press Station ID.
Press a or b to display Initial Setup.
Press Initial Setup.
Press a or b to display Tone/Pulse.
Press Tone/Pulse.
Enter your fax number (up to 20 digits) on the
Touchscreen, and then press OK.
f
Enter your name (up to 20 characters) using
the Touchscreen, and then press OK.
To enter numbers or special letters, press
repeatedly until the character you want to enter
appears, then press the character you want to
use.
Press Pulse(or Tone).
Press Stop/Exit.
g
Automatic Daylight
Savings Time
Note
14
• If you need to enter a character that is on the
same button as the last character, press c to
move the cursor to the right.
You can set the machine to change automatically for
daylight savings time. It will reset itself forward one
hour in the Spring and backward one hour in the Fall.
• If you entered a letter incorrectly and want to
change it, press d or c to move the cursor to the
incorrect character, press
.
a
b
c
d
e
f
Press MENU.
Press a or b to display General Setup.
Press General Setup.
Press a or b to display Auto Daylight.
Press Auto Daylight.
Press On(or Off).
g
Press Stop/Exit.
Note
If you make a mistake and want to start again,
For details, see Entering Text in Appendix C
of the User's Guide.
g
Press Stop/Exit.
Note
(USA only)
The Telephone Consumer Protection Act of 1991
makes it unlawful for any person to use a
computer or electronic device to send any
message via a telephone fax machine unless
such messages clearly contain, in a margin at the
top or bottom of each transmitted page, or on the
first page of the transmission, the date and time it
is sent and an identification of the business or
other entity or other individual sending the
message and the telephone number of the
sending machines or such business, other entity
or individual.
11
d
e
Enter the toll-free fax number: 1-877-268-9575.
Send in the Product
Registration and Test
Sheet (USA only)
Press Black Start.
15
Note
You will receive a confirmation fax of your Product
Registration.
You can also register your product online using the
On-Line Registration link from the installation
CD-ROM or visit
For MFC-790CW:
Now go to
a
Fill out the Product Registration and Test
Sheet.
Go to page 15
For MFC-990CW:
Now go to
To set up the cordless handset, go to Set up
To install your machine before you set up the
b
Put the sheet face down in the ADF (Automatic
Document Feeder) or face down on the
scanner glass.
c
Make sure
(Fax) is illuminated in Blue.
12
Set up the cordless handset (MFC-990CW only)
Install the battery
Charge the battery
16
17
a
Insert the connector a of the battery b in the
direction shown below.
a
Place the cordless handset on the cradle with
the dial pad facing forward.
2
1
Note
b
c
Place the battery in the position shown.
If your battery charge level is getting low, you
should charge the battery. You can see the
battery charge level indicator at the bottom right of
the LCD.
Set your country on the
cordless handset
18
The first time you install the battery, you must set your
country so that the cordless handset works correctly
on local telecommunication lines.
Install the battery cover by sliding it onto the
back of the handset.
a
The LCD shows:
Set Country
Press OK Key
b
c
Press Menu/OK.
Press a or b to choose your country.
Press Menu/OK.
d
Press 1 to confirm.
Note
Note
Be careful that you do not catch the battery
connector cord.
The LCD of the handset will display
“Searching for Base Unit” or
“Base Unit not detected” until the initial
setup of the machine is complete.
d
Charge the battery by leaving the cordless
handset in the cradle for at least 12 hours
before you use it.
You can continue to set up the handset during
this time.
13
Choose your language
on the cordless handset
(Canada only)
Position the antenna on
the base unit
19
21
a
Move the antenna to the up position as shown
below.
You can change the LCD language.
a
b
Press Menu/OK.
Press a or b to choose Select Language.
Press Menu/OK.
c
d
Press a or b to choose your language.
Press Menu/OK.
Press
.
Note
After replacement of the battery in the cordless
handset, you should set the date and time. (See
Date and Time in the Digital Cordless Handset
User’s Guide.)
Note
Avoid using in an area where it is difficult for radio
waves to penetrate such as in a reinforced
concrete building, near metal furniture or doors.
Choose a location
If you have purchased an optional cordless
handset, see Optional Cordless Handset in
the Digital Cordless Handset User’s Guide.
20
„ Choose a location where the temperature remains
between 50° F and 95° F (10° C and 35° C).
„ DO NOT put the cordless handset near heaters,
air conditioners, water or chemicals.
„ DO NOT expose the cordless handset to direct
sunlight, excessive heat, moisture, or dust.
„ DO NOT use the cordless handset near electro-
medical equipment.
„ We recommend at least 9.8 ft (3 m) between the
machine (base unit) or cordless handset and
possible sources of radio interference.
9.8 ft
(3 m)
9.8 ft
(3 m)
14
Choose your connection type
22
For USB interface cable
For Wired Network
For Wireless Network
Windows® and Macintosh®,
go to page 32
15
®
USB
Windows
For USB Interface Users
(For Windows® 2000 Professional/XP/XP Professional x64 Edition/
Windows Vista®)
Before you install
Install MFL-Pro Suite
23
24
a
Make sure that your computer is ON and you
are logged on with Administrator rights.
a
Put the supplied CD-ROM into your CD-ROM
drive. If the model name screen appears,
choose your machine. If the language screen
appears, choose your language.
Important
• DO NOT connect the USB cable yet.
• If there are any programs running, close
them.
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
• The screens may differ depending on the
operating system.
• The supplied CD-ROM includes ScanSoft™
PaperPort™ 11SE. This software supports
®
Note
Windows 2000 (SP4 or greater), XP (SP2 or
greater), XP Professional x64 Edition and
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
®
Windows Vista . Update to the latest
®
Windows Service Pack before installing
MFL-Pro Suite.
b
The CD-ROM main menu will appear. Click
Install MFL-Pro Suite.
b
Disconnect the machine from the AC outlet and
from your computer, if you already connected
an interface cable.
16
®
USB
Windows
f
Choose Local Connection, and then click
Next. The installation continues.
Note
• If this screen appears, click OK and restart
your computer.
• If the installation does not continue
automatically, open the main menu again by
ejecting and then reinserting the CD-ROM or
double-click the start.exe program from the
Pro Suite.
g
When this screen appears, go to the next step.
®
• For Windows Vista , when the User Account
Control screen appears, click Allow.
c
When the ScanSoft™ PaperPort™ 11SE
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
d
e
The installation of ScanSoft™ PaperPort™
11SE will automatically start and is followed by
the installation of MFL-Pro Suite.
When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
17
®
USB
Windows
c
Carefully route the USB cable through the
trench and out the back of the machine as
shown below and connect the cable to your
computer.
Connect the USB cable
25
Important
• DO NOT connect the machine to a USB port
on a keyboard or a non-powered USB hub.
• Connect the machine directly to your
computer.
a
Using both hands, use the plastic tabs on both
sides of the machine to lift the scanner cover
until it locks securely into the open position.
Important
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
d
Lift the scanner cover to release the lock a.
Gently push the scanner cover support
down b and close the scanner cover c.
1
3
2
b
Connect the USB cable to the USB socket
marked with a
symbol. You will find the
USB socket inside the machine on the right as
shown below.
LAN USB
18
®
USB
Windows
Connect the power cord
Finish and restart
26
27
a
Connect the power cord.
The installation will continue automatically.
a
Click Finish to restart your computer.
After restarting the computer, you must be
logged on with Administrator rights.
The installation screens appear one after
another.
Note
If an error message appears during the software
installation, run the Installation Diagnostics
located in Start/All Programs/Brother/
MFC-XXXX (where MFC-XXXX is your model
name).
Important
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
Note
The installation is now
complete.
®
For Windows Vista , when this screen appears,
click the check box and click Install to complete
the installation correctly.
Finish
Now go to
Proceed to Install Optional Applications on
b
When the On-Line Registration screen is
displayed, make your selection and follow the
on-screen instructions. Once you have
completed the registration process, close your
web browser to return to this window.
Then click Next.
19
®
USB
Macintosh
For USB Interface Users (For Mac OS® X 10.2.4 or greater)
b
Connect the USB cable to the USB socket
marked with a symbol. You will find the
USB socket inside the machine on the right as
shown below.
Before you install
23
a
Make sure your machine is connected to the
power and your Macintosh is ON. You must
be logged on with Administrator rights.
®
LAN USB
Important
®
• For Mac OS X 10.2.0 to 10.2.3 users,
®
upgrade to Mac OS X 10.2.4 or greater. (For
®
the latest information for Mac OS X, visit
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
c
Carefully route the USB cable through the
trench and out the back of the machine as
shown below and connect the cable to your
Connect the USB cable
®
Macintosh .
24
Important
• DO NOT connect the machine to a USB port
on a keyboard or a non-powered USB hub.
• Connect the machine directly to your
®
Macintosh .
a
Using both hands, use the plastic tabs on both
sides of the machine to lift the scanner cover
until it locks securely into the open position.
Important
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
d
Lift the scanner cover to release the lock a.
Gently push the scanner cover support
down b and close the scanner cover c.
1
3
2
20
®
USB
Macintosh
e
f
When this screen appears, click OK.
Install MFL-Pro Suite
25
a
Put the supplied CD-ROM into your CD-ROM
drive.
®
For Mac OS X 10.3.x or greater, the
installation of MFL-Pro Suite is now
complete.
®
For Mac OS X 10.2.4 to 10.2.8 users,
click Add.
b
c
Double-click the Start Here OSX icon to install.
g
h
Choose USB.
Choose Local Connection, and then click
Next. Follow the on-screen instructions.
Choose XXX-XXXX (where XXX-XXXX is your
model name), and then click Add.
Note
Please wait, it will take a few seconds for the
software to install. After the installation, click
Restart to finish installing the software.
i
Click Print Center, then Quit Print Center.
d
The Brother software will search for the Brother
device. During this time the following screen
will appear.
The installation of MFL-Pro Suite is now
complete.
21
®
USB
Macintosh
Install
Presto! PageManager
®
®
26
®
®
When Presto! PageManager is installed OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
®
®
documents using Presto! PageManager .
a
Double-click the Presto! PageManager icon
and follow the on-screen instructions.
®
For Mac OS X 10.2.4 to 10.3.8 users,
when this screen appears, click Go to
download the software from the Brother
Solutions Center website.
The installation is now
complete.
Finish
22
®
Wired Network
Windows
For Wired Network Interface Users
(For Windows® 2000 Professional/XP/XP Professional x64 Edition/
Windows Vista®)
Before you install
Connect the network
cable
23
24
a
Make sure that your computer is ON and you
are logged on with Administrator rights.
a
Using both hands, use the plastic tabs on both
sides of the machine to lift the scanner cover
until it locks securely into the open position.
Important
• If there are any programs running, close
them.
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
• The screens may differ depending on the
operating system.
• The supplied CD-ROM includes ScanSoft™
PaperPort™ 11SE. This software supports
®
Windows 2000 (SP4 or greater), XP (SP2 or
greater), XP Professional x64 Edition and
®
Windows Vista . Update to the latest
®
Windows Service Pack before installing
MFL-Pro Suite.
b
Connect the network cable to the LAN socket
marked with a
symbol. You will find the
LAN socket inside the machine on the left as
shown below.
Important
Before installation, if you are
using personal firewall
LAN USB
®
software (other than Windows
Firewall), anti-spyware or
antivirus applications,
temporarily disable them.
b
Disconnect the machine from the AC outlet.
23
®
Wired Network
Windows
c
Carefully route the network cable through the
trench and out the back of the machine. Then,
connect the cable to your network.
Connect the power cord
25
a
Connect the power cord.
Note
If both USB and LAN cables are being used,
guide both cables through the trench with one on
top of the other.
Important
If you have previously set up your machine for
a wireless network and then want to set it up
on a wired network, you should check that the
machine’s Network I/Fis set to Wired LAN.
The wireless network interface will become
inactive with this setting.
Important
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
d
Lift the scanner cover to release the lock a.
Gently push the scanner cover support
down b and close the scanner cover c.
On your machine, press MENU.
Press a or b to display Networkand press
Network.
1
Press Network I/F.
Press Wired LAN.
Press Stop/Exit.
3
2
24
®
Wired Network
Windows
Note
Install MFL-Pro Suite
• If this screen appears, click OK and restart
26
your computer.
a
Put the supplied CD-ROM into your CD-ROM
drive. If the model name screen appears,
choose your machine. If the language screen
appears, choose your language.
• If the installation does not continue
automatically, open the main menu again by
ejecting and then reinserting the CD-ROM or
double-click the start.exe program from the
Pro Suite.
®
• For Windows Vista , when the User Account
Control screen appears, click Allow.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
b
The CD-ROM main menu will appear. Click
Install MFL-Pro Suite.
c
When the ScanSoft™ PaperPort™ 11SE
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
d
e
The installation of ScanSoft™ PaperPort™
11SE will automatically start and is followed by
the installation of MFL-Pro Suite.
When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
25
®
Wired Network
Windows
f
Choose Wired Network Connection, and
then click Next.
Note
• If the machine is configured for your network,
choose the machine from the list, and then click
Next.
This window will not appear if there is only one
machine connected on the network, it will be
chosen automatically.
®
®
g
For Windows XP SP2/Windows Vista users,
when this screen appears, choose Change the
Firewall port settings to enable network
connection and continue with the
installation. (Recommended) and click Next.
If your machine shows APIPA in the IP
Address field, click Configure IP Address
and enter an IP address for your machine that
is suitable for your network.
• If the machine is not yet configured for use on
your network, the following screen appears.
®
If you are using a firewall other than Windows
®
Firewall or Windows Firewall is off, this screen
may appear.
Click OK.
The Configure IP Address window will
appear. Enter an IP address for your machine
that is suitable for your network by following the
on-screen instructions.
h
The installation of the Brother drivers will
automatically start. The installation screens
appear one after another.
See the instructions provided with your firewall
software for information on how to add the
following network ports.
„ For network scanning, add UDP port 54925.
„ For network PC-Fax receiving, add UDP port
54926.
„ If you still have trouble with your network
connection, add UDP port 137.
Important
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
Note
®
For Windows Vista , when this screen appears,
click the check box and click Install to complete
the installation correctly.
26
®
Wired Network
Windows
i
When the On-Line Registration screen is
displayed, make your selection and follow the
on-screen instructions. Once you have
completed the registration process, close your
web browser to return to this window.
Then click Next.
Install MFL-Pro Suite on
additional computers
(If needed)
28
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
Note
The MFL-Pro Suite Software License permits
installation on up to 2 network computers. if you
want to install MFL-Pro Suite on additional
computers, you can purchase additional NL-5
(five user) license agreements from your
authorized Brother dealer or contact Brother
customer service.
Finish and restart
27
The installation is now
complete.
a
Click Finish to restart your computer. After
restarting the computer, you must be logged on
with Administrator rights.
Finish
Now go to
Proceed to Install Optional Applications on
Note
If an error message appears during the software
installation, run the Installation Diagnostics
located in Start/All Programs/Brother/
MFC-XXXX (where MFC-XXXX is your model
name).
27
®
Wired Network
Macintosh
For Wired Network Interface Users (For Mac OS® X 10.2.4 or greater)
Before you install
Connect the network
cable
23
24
a
Make sure your machine is connected to the
a
Using both hands, use the plastic tabs on both
sides of the machine to lift the scanner cover
until it locks securely into the open position.
®
power and your Macintosh is ON. You must
be logged on with Administrator rights.
Important
®
• For Mac OS X 10.2.0 to 10.2.3 users,
®
upgrade to Mac OS X 10.2.4 or greater. (For
®
the latest information for Mac OS X, visit
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
• If you have previously set up your machine
for a wireless network and then want to set
it up on a wired network, you should check
that the machine’s Network I/F is set to
Wired LAN. The wireless network interface
will be inactive with this setting. On your
machine, press MENU.
Press a or b to display Network and press
Network.
Press Network I/F.
b
Connect the network cable to the LAN socket
marked with a
symbol. You will find the
LAN socket inside the machine on the left as
shown below.
Press Wired LAN.
Press Stop/Exit.
LAN USB
28
®
Wired Network
Macintosh
c
Carefully route the network cable through the
trench and out the back of the machine. Then,
connect the cable to your network.
Install MFL-Pro Suite
25
a
Put the supplied CD-ROM into your CD-ROM
drive.
Important
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
b
c
Double-click the Start Here OSX icon to install.
Note
If both USB and LAN cables are being used,
guide both cables through the trench with one on
top of the other.
d
Lift the scanner cover to release the lock a.
Gently push the scanner cover support
down b and close the scanner cover c.
1
Choose Wired Network Connection, and
then click Next. Follow the on-screen
instructions.
3
2
Note
Please wait, it will take a few seconds for the
software to install. After the installation, click
Restart to finish installing the software.
d
The Brother software will search for the Brother
device. During this time the following screen
will appear.
29
®
Wired Network
Macintosh
®
f
For Mac OS X 10.2.4 to 10.2.8 users,
click Add.
Note
• If the machine is configured for your network,
choose the machine from the list, and then click
OK. This window will not appear if there is only
one machine connected on the network, it will
g
h
i
Make the selection shown below.
• If this screen appears click OK.
Choose XXX-XXXX (where XXX-XXXX is your
model name), and then click Add.
®
Enter a name for your Macintosh in Display
Name up to 15 characters long and click OK.
Click Print Center, then Quit Print Center.
• If you want to use the machine’s Scan key to
scan over the network you must check the
Register your computer with the “Scan To”
function on the machine box.
• The name you enter will appear on the
machine’s LCD when you press the Scan key
and choose a scan option. (For more
information, see Network Scanning in the
Software User’s Guide on the CD-ROM.)
e
When this screen appears, click OK.
The installation of MFL-Pro Suite is now
complete.
®
For Mac OS X 10.3.x or greater, the
installation of MFL-Pro Suite is now
complete.
30
®
Wired Network
Macintosh
Install
Presto! PageManager
®
®
26
®
®
When Presto! PageManager is installed OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
®
®
documents using Presto! PageManager .
a
Double-click the Presto! PageManager icon
and follow the on-screen instructions.
®
For Mac OS X 10.2.4 to 10.3.8 users,
when this screen appears, click Go to
download the software from the Brother
Solutions Center website.
Install MFL-Pro Suite on
additional computers
27
(If needed)
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
The installation is now
complete.
Finish
31
For Wireless Network Users
For Wireless Network Interface Users
Before you begin
23
First you must configure the wireless network settings of your machine to communicate with your network access
point (router). After the machine is configured to communicate with your access point (router), computers on your
network will have access to the machine. To use the machine from these computers, you will need to install the
drivers and software. The following steps will guide you through the configuration and installation process.
To achieve optimum results with normal everyday document printing, place the Brother machine as close to the
network access point (router) as possible with minimal obstructions. Large objects and walls between the two
devices as well as interference from other electronic devices can affect the data transfer speed of your documents.
Due to these factors, wireless may not be the best method of connection for all types of documents and
applications. If you are printing large files, such as multi-page documents with mixed text and large graphics, you
may want to consider choosing wired Ethernet for a faster data transfer or USB for the fastest throughput speed.
Although the Brother MFC-790CW/MFC-990CW can be used in a both wired and wireless network, only one of
the connection methods can be used at a time.
Important
If you have previously configured the wireless settings of the machine you must reset the network
(LAN) settings before you can configure the wireless settings again.
On your machine, press MENU. Press a or b to display Networkand press Network.
Press a or b to display Factory Reset, and then press Factory Reset.
Press Yesto accept. Hold down Yesfor 2 seconds to confirm.
Note
The following instructions are for infrastructure mode.
To set up your machine in any other wireless environment you can find instructions in the Network User's
Guide on the CD-ROM.
You can view the Network User’s Guide by following the instructions below.
®
1 Turn on your computer/Macintosh . Insert the Brother CD-ROM into your CD-ROM drive.
®
For Windows :
2 Choose your model and the language. The CD-ROM main menu will appear.
3 Click Documentation, and then click HTML documents.
®
For Macintosh :
2 Double-click Documentation, and then double-click your language folder.
3 Double-click top.html.
Infrastructure Mode
1
4
2
3
a Access Point (router)
b Wireless Network machine (your machine)
c Wireless capable computer connected to the access point
d Wired computer connected to the access point
32
For Wireless Network Users
Confirm your network environment (Infrastructure Mode)
24
The following instructions will offer two methods for installing your Brother machine in a wireless network
environment. Both methods are for infrastructure mode, using a wireless router or access point that uses DHCP
to assign IP addresses. Choose a configuration method and proceed to the page indicated.
a
If your wireless router/access point does not support SecureEasySetup™, Wi-Fi Protected Setup™
or AOSS™, write down the wireless network settings of your access point or wireless router in the
area below.
Important
If you do not know this information (Network Name, WEP key or WPA2-PSK (Pre-Shared Key)),
you cannot continue the wireless setup. You should see the documentation provided with your
access point or wireless router, consult the router manufacturer, or your system administrator.
SSID (Service Set ID or Network name)
Authentication (Open System or Shared Key)/Encryption Type (None or WEP)
WEP Key (if needed)
WPA/WPA2-PSK Encryption type (TKIP or AES) (if needed)
WPA/WPA2-PSK (Pre-Shared Key) (if needed)
1
The WEP key is for 64-bit encrypted networks or 128-bit encrypted networks and can contain both numbers and letters. If you do
not know this information you should see the documentation provided with your access point or wireless router. This key is a 64-
bit or 128-bit value that must be entered in an ASCII or HEXADECIMAL format.
For example:
64-bit ASCII:
64-bit Hexadecimal:
128-bit ASCII:
Uses 5 text characters e.g. “Hello” (this is case sensitive)
Uses 10 digits of hexadecimal data e.g. “71f2234aba”
Uses 13 text characters e.g.
“Wirelesscomms” (this is case sensitive)
Uses 26 digits of hexadecimal data e.g.
128-bit Hexadecimal:
“71f2234ab56cd709e5412aa3ba”
2
WPA/WPA2-PSK is a Wi-Fi® Protected Access Pre-Shared Key, which lets the Brother wireless machine associate with access
points using TKIP or AES encryption (WPA-Personal). WPA/WPA2-PSK (TKIP or AES) uses a Pre-Shared Key (PSK) that is 8 or
more characters in length, up to a maximum of 63 characters.
See the Network User’s Guide for more details.
Now go to
b
If your wireless router/access point supports automatic wireless (one-push) setup
(SecureEasySetup™, Wi-Fi Protected Setup™ or AOSS™)
Now go to
33
For Wireless Network Users
Connecting the Brother machine to the wireless network
e
f
Press Infrastructure.
Important
Choose one of the options below: If your
network is configured for Authentication and
Encryption you must match the settings used
for your network.
You must have the wireless setting you wrote
before you proceed.
„ No Authentication or Encryption:
Press Open System, then press Nonefor
Encryption Type?Then press Yesto
Configure the wireless
settings (Typical
25
a
Wireless Setup in
infrastructure mode)
„ No Authentication with WEP Encryption:
Press Open System, then press WEPfor
On your machine, press MENU.
Press a or b to display Networkand press
Network.
„ Authentication with WEP Encryption:
Press WLAN.
Press Setup Wizard.
„ Authentication with WPA/WPA2-PSK
(TKIP or AES) Encryption:
When Switch Network interface to
wireless?is displayed, press Yesto accept.
This will start the wireless setup wizard.
To cancel, press No.
g
Choose the appropriate key number. Enter the
page 33 on the Touchscreen.
b
The machine will search for available SSIDs. If
a list of SSIDs is displayed, press a or b to
page 33. Press the SSID you want to connect
You can use the d and c keys to move the
cursor left and right.
The letters appear in this order: upper case and
then lower case.
To enter numbers or special letters, press
repeatedly until the character you want to enter
appears.
(For more information, see Entering Text for
Note
It will take several seconds to display a list of
available SSIDs.
If your access point is set to not broadcast the
SSID you will have to manually add the SSID
Press OKwhen you have entered all the
characters, then press Yesto apply your
c
d
page 33 using the Touchscreen.
You can use the d and c keys to move the
cursor left and right.
The letters appear in this order: upper case and
then lower case.
To enter numbers or special letters, press
repeatedly until the character you want to enter
appears.
(For more information, see Entering Text for
Press OKwhen you have entered all the
characters.
34
For Wireless Network Users
h
Press TKIPor AESfor Encryption Type?
Enter the WPA/WPA2-PSK password you
Touchscreen.
You can use the d and c keys to move the
cursor left and right.
The letters appear in this order: upper case and
then lower case.
To enter numbers or special letters, press
repeatedly until the character you want to enter
appears.
(For more information, see Entering Text for
Press OKwhen you have entered all the
characters, then press Yesto apply your
i
Your machine will now try to connect to your
wireless network using the information you
have entered. If successful, Connectedwill
appear on the LCD for approximately 1 minute.
If your machine does not successfully connect
to your network, verify your network settings
information.
If your access point does not have DHCP
enabled you will need to manually configure
the IP address, subnet mask and gateway of
the machine to suit your network. See the
Network User’s Guide for details.
Wireless setup is now complete. A four
level indicator at the top of your
machine’s LCD will show the wireless
signal strength of your access point or
router.
To install MFL-Pro Suite, continue to
step 26.
®
For Windows Users:
Now go to
Page 38
®
For Mac OS Users:
Now go to
Page 42
35
For Wireless Network Users
e
If the LCD shows Connected, the machine
Configure the wireless
settings using the
automatic wireless (one-
push) method
has successfully connected to your router or
access point. You can now use your machine
in a wireless network.
25
If the LCD shows Setting WLAN,
Connecting SES(Connecting WPSor
Connecting AOSS), then
Connection Failed, the machine has not
successfully connected to your router or
same message is indicated again, reset the
machine back to the default factory settings
and try again. For resetting, see Restore the
a
Confirm your wireless router or access point
has the SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™ symbol as shown below.
If the LCD shows Setting WLAN, then
Connection Failedor Incorrect Mode,
a session overlap or connection failure was
detected. (see the table below), the machine
has detected 2 or more routers or access
points on your network that have the
SecureEasySetup™, Wi-Fi Protected Setup™
mode or AOSS™ mode enabled. Make sure
that only one router or access point has the
SecureEasySetup™, Wi-Fi Protected Setup™
mode or AOSS™ mode enabled and try
b
Place the Brother machine within range of a
SecureEasySetup™, Wi-Fi Protected Setup™
or AOSS™ access point/router. The range may
differ depending on your environment. Refer to
the instructions provided with your access
point/router.
c
d
Push the SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™ button on your wireless
router or access point.
See the user’s guide for your wireless router or
access point for instructions.
LCD messages when using the
SES/WPS/AOSS control panel menu
On your machine, press MENU.
Press a or b to display Networkand press
Network.
Press WLAN.
Press SES/WPS/AOSS.
Setting WLAN
Searching or accessing the
access point and downloading
settings from the access point.
Connecting
SES/WPS/AOSS
Connecting to the access
point.
When Switch Network interface to
wireless?is displayed, press Yesto accept.
This will start the wireless setup wizard.
To cancel, press No.
Connection
Failed
Connection failed. If this is
shown after the LCD shows
Connecting
SES/WPS/AOSS, a session
overlap was detected.
This feature will automatically detect which
mode (SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™) your access point uses to
configure your machine.
Incorrect
Mode
A session overlap was
detected.
Connected
The machine has successfully
connected.
Note
If your wireless access point supports Wi-Fi
Protected Setup™ (PIN Method) and you want to
configure your machine using the PIN (Personal
Identification Number) Method, see Using the PIN
Method of Wi-Fi Protected Setup™ in the Network
User’s Guide on the CD-ROM.
Note
If you encounter a problem during setup,
temporarily place your machine closer to the
Wireless setup is now complete.
36
®
Wireless Network
Windows
Install the Drivers & Software
(For Windows® 2000 Professional/XP/XP Professional x64 Edition/
Windows Vista®)
Before you install
MFL-Pro Suite
Install MFL-Pro Suite
26
27
a
Make sure that your computer is ON and you
are logged on with Administrator rights.
a
Put the supplied CD-ROM into your CD-ROM
drive. If the model name screen appears,
choose your machine. If the language screen
appears, choose your language.
Important
• If there are any programs running, close
them.
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
• The screens may differ depending on the
operating system.
• The supplied CD-ROM includes ScanSoft™
PaperPort™ 11SE. This software supports
®
Windows 2000 (SP4 or greater), XP (SP2 or
Note
greater), XP Professional x64 Edition and
®
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
Windows Vista . Update to the latest
®
Windows Service Pack before installing
MFL-Pro Suite.
b
The CD-ROM main menu will appear. Click
Install MFL-Pro Suite.
Important
Before installation, if you are
using personal firewall
®
software (other than Windows
Firewall), anti-spyware or
antivirus applications,
temporarily disable them.
38
®
Wireless Network
Windows
f
Choose Wireless Network Connection, and
then click Next.
Note
• If this screen appears, click OK and restart
your computer.
• If the installation does not continue
automatically, open the main menu again by
ejecting and then reinserting the CD-ROM or
double-click the start.exe program from the
Pro Suite.
g
h
Click on Checked and confirmed check box,
and then click Next.
®
• For Windows Vista , when the User Account
Control screen appears, click Allow.
®
®
For Windows XP SP2/Windows Vista users,
when this screen appears, choose Change the
Firewall port settings to enable network
connection and continue with the
c
When the ScanSoft™ PaperPort™ 11SE
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
installation. (Recommended) and click Next.
®
If you are using a firewall other than Windows
®
Firewall or Windows Firewall is off, this screen
may appear.
d
e
The installation of ScanSoft™ PaperPort™
11SE will automatically start and is followed by
the installation of MFL-Pro Suite.
When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
See the instructions provided with your firewall
software for information on how to add the
following network ports.
„ For network scanning, add UDP port 54925.
„ For network PC-Fax receiving, add UDP port
54926.
„ If you still have trouble with your network
connection, add UDP port 137.
39
®
Wireless Network
Windows
i
The installation of the Brother drivers will
automatically start. The installation screens
appear one after another.
Note
• If the machine is configured for your network,
choose the machine from the list, and then click
Next.
Important
This window will not appear if there is only one
machine connected on the network, it will be
chosen automatically.
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
Note
®
For Windows Vista , when this screen appears,
click the check box and click Install to complete
the installation correctly.
If your machine shows APIPA in the IP
Address field, click Configure IP Address
and enter an IP address for your machine that
is suitable for your network.
j
When the On-Line Registration screen is
displayed, make your selection and follow the
on-screen instructions. Once you have
completed the registration process, close your
web browser to return to this window.
Then click Next.
• If your wireless settings fail, an error message
will appear during the installation of MFL-Pro
Suite and the installation will be terminated. If
page 33 and setup the wireless connection
again.
• If you are using WEP and the LCD displayed
‘Connected’ but your machine is not found,
make sure you entered the WEP key correctly.
The WEP key is case sensitive.
• If the machine is not yet configured for use on
your network, the following screen appears.
Click OK.
The Configure IP Address window will
appear. Enter an IP address for your machine
that is suitable for your network by following the
on-screen instructions.
40
®
Wireless Network
Windows
Finish and restart
28
a
Click Finish to restart your computer. After
restarting the computer, you must be logged on
with Administrator rights.
Note
If an error message appears during the software
installation, run the Installation Diagnostics
located in Start/All Programs/Brother/
MFC-XXXX (where MFC-XXXX is your model
name).
Install MFL-Pro Suite on
additional computers
29
(If needed)
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
Note
The MFL-Pro Suite Software License permits
installation on up to 2 network computers. if you
want to install MFL-Pro Suite on additional
computers, you can purchase additional NL-5
(five user) license agreements from your
authorized Brother dealer or contact Brother
customer service.
The installation is now
complete.
Finish
Now go to
Proceed to Install Optional Applications on
41
®
Wireless Network
Macintosh
Install the Drivers & Software
(For Mac OS® X 10.2.4 or greater)
c
Before you install
MFL-Pro Suite
Choose Wireless Network Connection, and
then click Next.
26
a
Make sure your machine is connected to the
power and your Macintosh is ON. You must
be logged on with Administrator rights.
®
Important
®
• For Mac OS X 10.2.0 to 10.2.3 users,
®
upgrade to Mac OS X 10.2.4 or greater. (For
d
Click on the Checked and confirmed check
box, and then click Next.
Follow the on-screen instructions.
®
the latest information for Mac OS X, visit
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
Install MFL-Pro Suite
27
a
Put the supplied CD-ROM into your CD-ROM
drive.
Note
Please wait, it will take a few seconds for the
software to install. After the installation, click
Restart to finish installing the software.
e
The Brother software will search for the Brother
device. During this time the following screen
will appear.
b
Double-click the Start Here OSX icon to install.
42
®
Wireless Network
Macintosh
f
When this screen appears, click OK.
Note
• If the machine is configured for your network,
choose the machine from the list, and then click
OK.
This window will not appear if there is only one
machine connected on the network, it will be
®
For Mac OS X 10.3.x or greater, the
installation of MFL-Pro Suite is now
complete.
®
g
h
i
For Mac OS X 10.2.4 to 10.2.8 users,
click Add.
•
If your machine is not detected, go to step 24
again.
• If you are using WEP and the LCD displayed
‘Connected’ but your machine is not found,
make sure you entered the WEP key correctly.
The WEP key is case sensitive.
Make the selection shown below.
• If this screen appears click OK.
®
Enter a name for your Macintosh in
Choose XXX-XXXX (where XXX-XXXX is your
model name), and then click Add.
Display Name up to 15 characters long and
j
Click Print Center, then Quit Print Center.
• If you want to use the machine’s Scan key to
scan over the network you must check the
Register your computer with the “Scan To”
function on the machine box.
• The name you enter will appear on the
machine’s LCD when you press the Scan key
and choose a scan option. (For more
information, see Network Scanning in the
Software User’s Guide on the CD-ROM.)
The installation of MFL-Pro Suite is now
complete.
43
®
Wireless Network
Macintosh
Install
Presto! PageManager
®
®
28
®
®
When Presto! PageManager is installed OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
®
®
documents using Presto! PageManager .
a
Double-click the Presto! PageManager icon
and follow the on-screen instructions.
®
For Mac OS X 10.2.4 to 10.3.8 users,
when this screen appears, click Go to
download the software from the Brother
Solutions Center website.
Install MFL-Pro Suite on
additional computers
29
(If needed)
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
The installation is now
complete.
Finish
44
®
Install Optional Applications
Windows
Install FaceFilter Studio
supported by
Install FaceFilter Studio
Help
1
2
Reallusion, Inc
FaceFilter Studio is an easy-to-use borderless photo
printing application. FaceFilter Studio also lets you
edit your photo data and add photo effects such as
red eye reduction or skin tone enhancement.
To get instructions on how to use FaceFilter Studio,
download and install FaceFilter Studio Help.
a
To run FaceFilter Studio, go to
Start/All Programs/Reallusion/
FaceFilter Studio on your computer.
Important
• The machine must be ON and connected to
the computer.
b
c
Click the
button on the upper right corner
• The computer must be connected to the
Internet.
of the screen.
Click Check for updates to go to the
Reallusion update web page.
a
b
Open the main menu again by ejecting and
then reinserting the CD-ROM or by double-
clicking the start.exe program from the root
folder.
The CD-ROM main menu will appear. Choose
your language and then click Additional
Applications.
d
e
Click the Download button and choose a folder
to save the file in.
Close FaceFilter Studio before you start the
installer for FaceFilter Studio Help.
Double-click the downloaded file from the
folder you specified and follow the on-screen
instructions for installation.
c
Click the FaceFilter Studio button to install.
Note
To view the complete FaceFilter Studio Help,
choose Start/All Programs/Reallusion/
FaceFilter Studio/FaceFilter Studio Help on
your computer.
45
®
Install Optional Applications
Windows
Install
BookScan&Whiteboard
3
Suite supported by
Reallusion, Inc
You can install BookScan&Whiteboard Suite.
The BookScan Enhancer software can correct your
scanned book images automatically. The
Whiteboard Enhancer software cleans up and
enhances text and images from photos taken of your
whiteboard. (Internet access required.)
Important
• The machine must be ON and connected to
the computer.
• The computer must be connected to the
Internet.
a
b
Open the main menu again by ejecting and
then reinserting the CD-ROM or by double-
clicking the start.exe program from the root
folder.
The CD-ROM main menu will appear. Choose
your language and then click Additional
Applications.
c
Click the BookScan&Whiteboard Suite
button to install.
46
For Network Users
BRAdmin Light utility (For Windows® users)
BRAdmin Light is a utility for initial setup of Brother network connected devices. It also can search for Brother
products on your network, view the status and configure basic network settings, such as IP address.
Note
If you require more advanced printer management, use the latest Brother BRAdmin Professional utility version
Install the BRAdmin Light
configuration utility
Set your IP address, Subnet Mask
and Gateway using BRAdmin Light
Note
a
Click Advanced and then Network Utilities on
the menu screen.
If you have a DHCP/BOOTP/RARP server in your
network, you don’t have to do the following
operation. The machine will automatically obtain
its own IP address.
a
Start BRAdmin Light. It will search for new
devices automatically.
b
Double-click the unconfigured device.
b
Click BRAdmin Light and follow the on-screen
instructions.
c
d
Choose STATIC for the Boot Method. Enter
the IP Address, Subnet Mask and Gateway,
and then click OK.
The address information will be saved to the
machine.
47
For Network Users
BRAdmin Light utility (For Mac OS® X users)
BRAdmin Light is a utility for initial setup of Brother network connected devices. It also can search for Brother
products on your network, view the status and configure basic network settings, such as IP address from a
®
computer running Mac OS X 10.2.4 or greater.
The BRAdmin Light software will be installed automatically when you install the printer driver. If you have already
installed the printer driver, you don’t have to install BRAdmin Light again. For more information on BRAdmin Light,
d
Double-click the unconfigured device.
Set your IP address, Subnet Mask
and Gateway using BRAdmin Light
Note
• If you have a DHCP/BOOTP/RARP server in
your network, you don’t have to do the
following operation. The machine will
automatically obtain its own IP address.
• Make sure that version 1.4.1_07 or later of
Java™ client software is installed on your
computer.
e
Choose STATIC for the Boot Method. Enter
the IP Address, Subnet Mask and Gateway,
and then click OK.
a
Double-click the Macintosh HD icon on your
desktop.
f
The address information will be saved to the
machine.
b
c
Choose Library, Printers, Brother and then
Utilities.
Double-click the file BRAdmin Light.jar and
run the software. BRAdmin Light will then
search for new devices automatically.
48
For Wireless Network Users
Restore the network settings to factory default
To restore all network settings of the internal Print/Scan server to factory default, please follow the steps below.
a
Make sure the machine is not operating, then disconnect all the cables from the machine (except the power
cord).
b
c
d
e
f
Press MENU.
Press a or b to display Networkand press Network.
Press a or b to display Factory Resetand press Factory Reset.
Press Yes.
Hold down Yesfor 2 seconds to confirm.
The machine will restart, re-connect cables once this is complete.
g
Entering Text for Wireless Settings
When you are setting certain menu selections, you may need to enter text into the machine. Press
to choose
numbers, characters and special characters. Up to four letters are assigned to each button on the Touchscreen.
By pressing the correct button repeatedly, you can access the character you want.
OK
Inserting spaces
To enter a space, press
to choose special characters, then press the space button
or
.
Note
The characters available may differ depending on your country.
Making corrections
If you entered an incorrect letter and want to change it, use the arrow buttons to move the cursor under the
incorrect character. Then press
cursor and entering a character.
. Re-enter the correct character. You can also insert letters by moving the
Repeating letters
If you need to enter a letter that is on the same button as the letter before, press c to move the cursor to the right
before you press the button again.
49
Consumables
Replacement consumables
When the time comes to replace ink cartridges, an error message will be indicated on the LCD. For more
information about the ink cartridges for your machine, visit http://www.brother.com/original/ or contact your local
Brother re-seller.
Ink cartridge
Black
Yellow
LC61Y
Cyan
Magenta
LC61M
LC61BK
LC61C
What is Innobella™?
Innobella™ is a range of genuine consumables offered by Brother.
The name "Innobella™" derives from the words "Innovation" and "Bella"
(meaning "Beautiful" in Italian) and is a representation of the "innovative"
technology providing you with "beautiful" and "long lasting" print results.
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Multi-Function Link is a registered trademark of Brother International Corporation.
Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the United States and other countries.
Microsoft, Windows and Windows Server are registered trademarks of Microsoft Corporation in the United States and/or other countries.
Macintosh and TrueType are registered trademarks of Apple Inc.
Nuance, the Nuance logo, PaperPort and ScanSoft are trademarks or registered trademarks of Nuance Communications, Inc. or its affiliates
in the United States and/or other countries.
Presto! PageManager is a registered trademark of NewSoft Technology Corporation.
PictBridge is a trademark.
FaceFilter Studio is a trademark of Reallusion, Inc.
BROADCOM, SecureEasySetup and the SecureEasySetup logo are trademarks or registered trademarks of Broadcom Corporation in the
United States and/or other countries.
AOSS is a trademark of Buffalo Inc.
Wi-Fi, WPA and WPA2 are registered trademarks and Wi-Fi Protected Setup is a trademark of Wi-Fi Alliance.
Each company whose software title is mentioned in this manual has a Software License Agreement specific to its proprietary programs.
All other brand and product names mentioned in this manual are trademarks or registered trademarks of their
respective companies.
Compilation and Publication
Under the supervision of Brother Industries, Ltd., this manual has been compiled and published, covering the latest product descriptions and
specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for
any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other
errors relating to the publication.
Copyright and License
©2008 Brother Industries, Ltd.
This product includes software developed by the following vendors:
©1983-1998 PACIFIC SOFTWORKS, INC.
This product includes the “KASAGO TCP/IP” software developed by ELMIC WESCOM, Inc.
©2008 Devicescape Software, Inc.
|
ALFA OKIPAGE 20DX User Manual
Broan 178F User Manual
Brother Laser Multifunction Printer MFC 895DW User Manual
Bryant 704D User Manual
Cornelius 318949000 User Manual
Crestron electronic Battery Pack TPS 6X BTP User Manual
Epson WorkForce 840 User Manual
HomeSeer Technologies Single Package Air Conditioner 13 SEER User Manual
HP Hewlett Packard CM8050 User Manual
Hunter Fan 30010 User Manual