USA
AVC Tech
777 Mark St., Wood Dale, IL 60191
Tel : 800-568-0060 or 630-595-0123
Fax : 800-784-9422 or 630-595-2345
e-mail : [email protected]
NEW ZEALAND
TRANSTECH DISTRIBUTORS Ltd.
PO Box 12985 Penrose,
Auckland New Zealand
Tel : 09-571-0775
Fax : 09-571-0776
e-mail : [email protected]
AUSTRALIA
Thomas Electronics Australia Pty Ltd.
3 Sheridan Close
Milperra NSW 2214, Australia
Tel : +61 2 9773 7400
MODELS : Q261 Q320 Q321 Q400 Q401
Fax : 61 2 9773 7177
Attn : Ms. Shiely Poniman
GERMANY
Hyundai ImageQuest Europe GmbH
Geheimrat Hummel Platz 2
65239, Hochheim, Germany
Tel : 06146 / 904 444
Fax : 06146 / 904 410
e-mail : [email protected]
JAPAN
Hyundai ImageQuest JAPAN
Shin-Hibiya Bldg, East 5F 1-3-6
Uchisaiwai-Cho, Chiyoda-ku,
Tokyo, Japan 100-0011
Tel : 03-5157-2286
Fax : 03-5157-2284
e-mail : [email protected]
C/S P.J.Kim
P/N 632 0239 801 Rev.00
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Information
User Instructions
The Federal Communications Commission Radio Frequency Interference Statement includes
thefollowing warning :
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital
devicepursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
aresidential installation. This equipment generates, uses, and can radiate radio frequency energy and,
ifnot installed and used in accordance with the instructions, may cause harmful interference to
radiocommunications. However, there is no guarantee that interference will not occur in a
particularinstallation.
If this equipment does cause harmful interference to radio or television receptions, which can
bedetermined by turning the equipment off and on, the user is encouraged to try to correct
theinterference by one or more of the following measures :
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.
• Consult the dealer or an experienced radio/TV technician for assistance.
User Information
Changes or modifications not expressly approved by the party responsible for compliance could
voidthe user’s authority to operate the equipment.Connecting of peripherals requires the use of
grounded shielded signal cables.
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Important Tip
Image Retention Effect (Image Sticking)
1. Cause :
- Image Retention Effect may come from displaying a still picture in certain period of time with at a
certain area continuously, as the feature of LCD panel. This is caused due to brightness degradation.
Many LCD manufacturers are trying to overcome this limitation.
2. Prevention
- To avoid this matter, use the product after reducing brightness and contrast, especially when a still
image is displaying for a long time. (Contrast 50/Brightness 50 - See 32 page)
Once image retention occurs, use the mode that displays more motion pictures. It will help reduce this
matter.
3. Solution
- The temporary image sticking would decrease with displaying Full-White pattern during 10 hours.
* The permanent image sticking could not take off under the latest technology.
This method may be used to eliminate a temporary retained image that occurs after displaying a still
image for a certain period of time. Since it may take several minutes to several hours to remove image
sticking, it is recommendable to display motion pictures during 2~3 minutes every hour when keeping
displaying a still image. As image sticking is influenced by the brightness of a still image being
displayed and its display time, it is recommended that you reduce the brightness of the screen when
displaying a still image for a long time.
* Image Sticking does not come under the warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Sticking Precaution
When watching a still Image within motion pictures and
Panorama/Wide/4:3 screen
Panorama, Wide, 4:3 screen
Box still image
1. Note :
- When the central area of the screen and the screen edges are fixed, the different brightness level of
the edges may cause image retention on the edges when watching for a long time
- This phenomenon is the same matter to other LCD manufacturers. Please do not watch a still image
for a long time.
- If you watch a still image for a long time, this may damage your TV.
* This matter does not come under the warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Features
Integrated HDTV
An HDTV has a built-in ATSC digital tuner.
It does not need a separate set-top box to receive over the-air DTV signal.
Dual Scan/Multi-Viewing
You can program analog TV broadcasting and digital TV broadcasting automatically at the same time
for multi-viewing.
A Wide Array of Screen Settings
You can choose different screen settings depending on the type of program you are watching or the
surrounding conditions (the outside weather conditions). You can switch among Standard, Dynamic,
Movie, and Mild options or you can configure the screen settings for yourself.
A Wide Array of Sound Settings
You can choose an optimal sound setting for the type of program you are watching.
You can switch among Standard, News, Music, and Sport options or you can configure the sound
settings for yourself.
TV Program Reservation
If you reserve a digital TV program you are going to watch, the channel you are currently watching is
automatically switched to the reserved channel.
Favorite Channel Memory
You can memorize the channels you are watching frequently.
SRS TrueSurround XT
You can enjoy dynamic and surround sound with ordinary speakers.
Dolby-Digital
When receiving digital broadcast signal, you can enjoy dynamic and surround sound with two
ordinary speakers just like Dolby 5.1.
A Variety of Aspect Ratios
You can adjust the screen size at your preference.
Auto On/Off Function
This function allows you to turn on or off your TV at the preset time.
Game Prevention Function
This function is designed to prevent a VCR or game player from being connected to the TV.
Memory Card Support
You can enjoy photo images, music files and movies by inserting a variety of memory cards.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Table of Contents
How to Select MTS(Multi-Channel Sound) ...........................43
How to Listen to SRS TruSurround XT (Surround) ................44
How to Set the Output of Subwoofer ...................................45
How to Set the Audio Output ...............................................46
How to Set the Digital Audio Output ....................................47
How to Set Audio Language ................................................48
General Information
Safety Precaution ................................................................5
Contents of the Package .......................................................9
Products Sold Separately ......................................................9
Kensington Lock Anti-theft Device ......................................10
How to Mount and Detach The Speakers ...........................11
How to adjust the view angle ..............................................12
Parts Names and Functions ................................................13
Remote Control ...................................................................17
Channel Setup
How to Store Channels Automatically ..................................49
How to Add/Erase Channels Manually .................................50
How to Set Favorite Channels .............................................51
How to Fine Tune Channel Reception ..................................52
How to the LNA (Low-Noise-Amplifier) Feature ...................53
Connections
How to Watch Both Analog and Digital Broadcasts
with a Single Antenna .........................................................19
How to Watch Both Analog and Digital Broadcasts
Function Setup
with Two Antennas .............................................................20
Before Connecting the Video/Audio Connections to
How to Choose Your Language ...........................................54
How to Set Clock, On/Off Time, Sleep Time ........................55
How to Set the Geometry in PC Mode ..................................57
How to Set Key Lock ...........................................................58
How To Set Block Program .................................................60
How to View Closed Captions ..............................................62
External Devices... .............................................................21
How to Connect a VCR/Cable Receiver ................................22
How to Connect a DTV Receiver or DVD Player ....................23
How to Connect a Camcorder/Game Player .........................24
How to Connect to a PC ......................................................25
HDMI Connection ................................................................27
How to Connect an External Visual Device ...........................29
How to Use Digital Sound ....................................................30
DTV Setup
How to Use the Current Channel Guide ..............................64
How to Reserve TV Programs Using the Total Channel Guide ....64
How to Use TV Program Reservation ...................................65
How to Check or Cancel a Scheduled TV Program ...............66
Picture Setup
How to Select the Picture Mode ..........................................31
How to Set the Desired Picture ...........................................32
How to Adjust the Color Temperature of the Screen ............33
How to Select the Aspect Ratio ...........................................34
How to Watch the PIP .........................................................36
How to Set the INPUT for the Sub-Picture ...........................37
How to Reduce Noise ..........................................................39
How to Use Memory Mode ...............................67
Appendix
How to Use an External Device Using the Remote Control ...75
Glossary .............................................................................78
Troubleshooting ..................................................................81
Care and Cleaning ..............................................................83
Product Specifications ........................................................84
Sound Setup
How to Select the Audio Mode ............................................40
How to Adjust the Desired Audio Mode ..............................41
How to Use the Automatic Volume Control ..........................42
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precaution
The contents of this section are provided for the safety of users and their property.
Please read the instructions carefully before using.
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the TV, be sure the antenna or
cable system is grounded so as to provide some protection against voltage surges
and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA
No.70-1984, provides information about proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
Do not connect multiple electrical
Example of Grounding According to National Electrical Code
Instruction
appliances to a single outlet.
- It may cause a fire due to overheating from
the outlet.
Make sure to remove the speakers
before moving the TV with speakers
mounted on it.
- When the speakers are detached from the
unit while carrying it, this may cause damage
to the unit or personal injury.
Do not use or store a flammable
spray or inflammable things near the
TV.
- They may cause explosion or fire.
Any necessary action such as making the
antenna cable loop at the entrance of the
building should be taken to prevent rainwater
on the outdoor antenna cable from possibly
running into the indoor.
Do not install the TV in a
bookshelf, closet, or a place where
there is poor air circulation.
- Fire may be caused due to the rise of
internal temperature.
- If raindrop gets into the LCD TV, it may
cause a fire or an electric shock.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
If there is a persistent accumulation
of dusts or water on the plug, please
make sure to wipe it off using a dry
Do not use a damaged power cord
or plug, or loose outlet.
- It may cause electric shock or fire.
cloth.
- It may cause a fire or an electric shock.
Firmly plug in the power cord so that
it does not pull out.
- An unstable connection may cause fire.
Do not install in a place where there
is oil, smoke, excessive humidity, or
where water may be sprinkled on it.
- This may cause electric shock or fire.
Do not put a water bowl, vase,
candle, bug repellant smoke,
cigarette, plants, or heavy thing on
Do not install on an unstable place
the TV.
- It may cause electric shock or fire and also
heavy things may cause injury when they
fall.
or small support.
- This may cause the TV to fall, resulting in
serious injury to a child or adult.
Never attempt to open, fix, or modify
your TV.
When the TV produces abnormal noise,
burning smell, or smoke, unplug the TV
immediately and call a service center.
- Electric shock or fire may be caused.
- When there is a need for fixing, call a
service center. Fire or electric shock may be
caused.
Do not put a metallic object like chopstick,
wire, or puncher or inflammables like paper
or a match in a vent, headphone jack, or AV
jacks of the TV.
- Electric shock or fire may be caused.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precaution ......................................Continued from previous page
The contents of this section are provided for the safety of users and their property.
Please read the instructions carefully before using.
Do not block ventilating slits with a table
cloth.
- Blocking the ventilation slits may produce
inner heat increase, resulting in a fire.
Do not place any heat sources such as
Keep the TV at least 10cm away from the
radiators and heat registers, etc. near the TV.
wall for ventilation.
- It may cause a fire.
- Fire may be caused due to the rise of inner
temperature.
Do not place toys and cookies, etc. on the TV,
which may attract children’s attention.
- If it falls over on children, it may cause serious
injury.
When cleaning the TV, make sure to
disconnect the power plug and use a dry, soft
Do not allow children to climb or play on the
cloth for a cleanup.
TV.
- Please avoid using chemicals such as wax,
- If it falls over on children, it may cause
benzene, alcohol, thinner, mosquito spray,
serious injury.
air freshener, lubricant or synthetic
detergent.
Unplug when you do not use your TV for a
Consult a service center or customer service
for inside cleaning about once a year.
- When dust is piled inside the TV for long
time, fire or malfunction may be caused.
long time.
- If dust is stacked on the TV, electric shock
or fire may be caused from heat, fire, or
deterioration of insulation.
When moving the TV, two or more people are
advised to carry it.
- Injury or damage may be caused when the
TV falls.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Unplug the product during lightning or
thunderstorms and never touch the antenna
cable.
- It may cause a fire or an electric shock.
Keep the remote control batteries out of
sight and out reach of children.
- If your child swallows a battery, see your
doctor immediately.
Do not install the product on the floor.
- If it falls over, your child may be injured.
When replacing batteries, make sure to
match the batteries to the (+) and (-) marks
in the battery compartment.
- Mismatching of polarities may result in
internal damage to batteries, fire due to
leakage or contamination.
In the event of damaging or dropping the
product, switch off the power and remove
the plug.
Always use the standard batteries and avoid
using old batteries together with new ones.
- Otherwise it may result in internal damage
to batteries, fire due to leakage or
contamination.
- Using a damaged product may cause an
electric shock or a fire.
- Contact your local service center.
Before moving the product, ensure to switch
off the power and unplug all the electrical
cords and the external connection cords such
as an antenna cable and other source
connections, etc.
Consult a service center or customer
service for inside cleaning about
once a year.
- When dust is piled inside the PDP for long time,
fire or malfunction may be caused.
Ensure the power cord doesn’t trail
across any hot objects like a heater.
- This may cause a fire or an electric shock.
- An electrical cord(s) may be damaged,
resulting in a fire or an electrical shock.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of the Package
hen opening the package, please ensure to check the following accessories provided.
Antenna Cable
Power Cord
(coaxial cable)
Remote Control & 2 batteries
(1.5V AAA)
User's Guide
Products Sold Separately
If you want to purchase separately sold products, consult a service center, electronics shops, or parts seller.
S-video Cable
Hdmi cable
Wall Mounting Support
Component Cable
(Y, Pb, Pr)
Composite Cable
(Video/Audio)
Audio Cable (DIV/DVD)
Audio Cable (PC)
PC signal Cable (D-SUB)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Kensington Lock Anti-theft Device
- This display unit supports Kensington standard security lock to prevent theft.
- You should purchase the Kensington lock device personally, if you need. The security lock is available at an
electronics shop.
- For more information, please refer to the following contact information..
* Kensington Technology Group
• Address : 2000 Alameda de las Pulgas 2F san mateo, California 94403-1289
• Tel : +1 650 572 2700
• Fax : +1 650 572 9675
Model
Model
10
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Mount and Detach The Speakers - For Q26*/Q32* Model only
You can attach the speakers to the base of the unit or use them separately.
How to mount the speakers onto the base of the unit
1. Tilt the unit backward until its base faces to yourself (See next page How to Adjust the View Angle).
2. Prepare your right speaker first. Remove the tube of hooks and verify that the hooks place in the upright
position.
3. Align the right speaker hooks with the cavity holes marked with “SPEAKER” under the base.
4. Slide the right speaker inward till the tension hooks are securely locked as shown in Figure below.
5. Repeat step 2~4 for the left speaker.
The right and left speakers are labeled R (Right) and L (Left) on their rear, respectively.
Right Speaker
Left Speaker
When detaching the speakers
When you are going to detach the speakers,
press the tension hook and remove the
speakers in reverse order as shown in the
above figure.
The provided speakers are designed for this product only. It is recommended not to connect
the speakers to other device. When connecting other amplifier, the amplifier output should be
within 10W. The output that exceeds 10W may cause fire.
WARNING
Make sure to remove the speakers before moving the TV. When the speakers are detached
from the unit while carrying it, this may cause damage to the unit or personal injury.
ALERT
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to adjust the view angle - For Q26*/Q32* Model only
You can adjust the panel downward or upward at a 0~15 degree angle.
15O
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Names and Functions - For Q26*/32* Model only
Front View
* This product image may be a bit different from the actual product.
Volume buttons
Power button
Use these buttons for your desired sound level.
These buttons also serve as the cursor of
Select/Adjust when in Menu mode.
Use this button to turn on or off the TV.
Remote sensor and power LED.
- Point the remote control toward here.
- It displays standby or operation status.
Channel buttons
Use these buttons to change channels. These
buttons also serve as the cursor of Down and
Up buttons when in Menu mode.
- Power Indicator Status -
Indicator
Red
Status
Standby
Power on
Select button
Use this button to select each item of menu.
Green
Menu button
Remote sensor and power LED.
See page 11 for information on how to mount
speakers.
Use this button to display or exit from menus.
Source button
Use this button to switch among inputs
connected to the TV.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Rear View
HDMI Option
* This product image may be a bit different from the actual product.
Power switch
Use this switch to turn on/off power.
Component 2 Audio input terminal
Component 1 Video input terminal
Component 1 Audio input terminal
S-Video input terminal
Antenna 2 (DTV) input terminal
Digital Audio output terminal for
coaxial cable
Power (AC) input terminal
Connect the power cord to this
terminal.
SPDF optical digital audio output
terminal
Video input terminal
Speaker terminal
Connect your speaker jacks
HDMI (or DVI) Video input terminal
D-SUB input terminal
S-Video/Video Audio input terminal
RS-232 input terminal
Connect to the RS-232 terminal of a
PC to check its service.
Memory Card Slot
USB Input Terminal
For Q320 Model only
HDMI (or DVI)/D-SUB Audio input
terminal
Subwoofer output terminal
When producing bass, connect the
cable to the woofer with *AMP.
Monitor Video output terminal
Monitor Audio output terminal
Antenna 1 (Analog/DTV) input
terminal
Component 2 Video input terminal
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Names and Functions - For Q40* Model only
Front View
* This product image may be a bit different from the actual product.
Use this button to switch among inputs
Speaker
Power switch
connected to the TV.
Menu button
Use this switch to turn on/off power.
Use this button to display or exit from menus.
Remote sensor and power LED.
Select button
Use this button to select each item of menu.
- Point the remote control toward here.
- It displays standby or operation status.
- Power Indicator Status -
Channel buttons
Use these buttons to change channels. These
buttons also serve as the cursor of Down and
Up buttons when in Menu mode.
Indicator
Red
Status
Standby
Power on
Green
Volume buttons
Use these buttons for your desired sound level.
These buttons also serve as the cursor of
Select/Adjust when in Menu mode.
Power button
Use this button to turn on or off the TV.
Source button
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Rear View
HDMI Option
* This product image may be a bit different from the actual product.
Power (AC) input terminal
Connect the power cord to this
terminal.
Component 1 Video input terminal
S-Video input terminal
coaxial cable
SPDF optical digital audio
output terminal
Video input terminal
HDMI (or DVI) Video input terminal
D-SUB input terminal
Memory Card Slot
USB Input Terminal
For Q400 Model only
S-Video/Video Audio input terminal
RS-232 input terminal
Connect to the RS-232 terminal of a
PC to check its service.
HDMI (or DVI)/D-SUB Audio input
terminal
Subwoofer output terminal
Monitor Video output terminal
Monitor Audio output terminal
When producing bass, connect the
cable to the woofer with *AMP.
Component 2 Video input terminal
Component 2 Audio input terminal
Component 1 Audio input terminal
Antenna 1 (Analog/DTV) input
terminal
Antenna 2 (DTV) input terminal
Digital Audio output terminal for
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
1. POWER/STANDBY
2. MUTE
This button is also used when setting up to use other external
device.
3. PIP FUNCTIONS
- PIP
: Use this button for PIP On/Off.
- INPUT
: Use this button to select the input source of sub-picture.
- SIZE
: Use this button to select the size of sub-picture.
- SWAP
: Use this button to swap main and sub-picture.
- POSITION
: Use this button to select the position of sub-picture.
4. A/D+
Use this button to switch analog input signal to digital signal.
5. Previous Channel
Use this button to return to the previous channel.
6. Other external device selection ( 75P)
7. MENU SELECTION
Use this button to select menu items.
8. LEFT/RIGHT MOVE/ADJUST
Use these buttons to move between menu items or to adjust
each item.
9. MENU
Use this button to call the OSD to the screen.
10. EXIT
Use this button to end the OSD.
11. CHANNEL SELECTION
Use this button to select the channel.
12-13. SUB-PICTURE CHANNEL SELECTION
14. PC AUTO
Use this button to automatically adjust the screen in PC Mode.
15. DTV-GUIDE
30
Use this button to see digital broadcast information.
16. SRS
Use this button to select 3D surround sound.
17. SAP
Use this button to listen in a foreign language or in Stereo
Mode.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Using buttons when in Memory Mode
* For Q320/Q400 Model only
18. PICTURE MODE
19. SOUND MODE
The following buttons are used differently in each
menu. (See pages 67~74 for more details.)
20. BOOK-MARK
Use this button to select/deselect your frequently-used
Power Saving Function when listening to music
Music Playback Setting (Repeat 1, Repeat All, Sequence)
Select, Start, Pause/Playback
channel.
21. FAVORITE
Use this button when watching your favorite channel.
22. ADD/ERASE
Move between file listings, Previous Track/Next Track,
Reverse/Fast Forward, Photo Rotation
Use this button to add or erase channels.
23. INFOMATION
Exit, Cancel
Use this button to display resolution or various program
information.
Eject Card
24. SOURCE
Slide Show
Use this button to select External Input or Memory Mode.
25. VOLUME
Zoom In
26. STILL
Check Version (Initial Screen), Check Running Time (Movie Mode)
Hide Menu
27. SLEEP
28. ASPECT RATIO
Use this button to change the picture size.
When Shifting into Memory Mode
29. NUMERIC KEYS
Other buttons available in Memory Mode
30. Use this buttons to use other manufacturer’s DVD or
VCR.
How to Insert Batteries in Remote Control
Press and hold ∆ part and push
to open cover.
Insert batteries with proper
polarities of +and -.
Use the remote control with cover
closed.
* Battery type :1.5V/AAA
18
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Watch Both Analog and Digital Broadcasts with a Single Antenna
You can watch both analog and digital broadcasts by connecting a single antenna.
Connection Method
Make sure that the antenna cable is connected to ANT 1 (ATV/DTV).
- Antenna or Cable service without a cable box connections
- For optimum picture quality, adjust antenna direction if need,
VHF Antenna
UHF Antenna
- When inserting a 75 ohm coaxial cable into the input connection, ensure the wire tip not to bend.
- If you experience poor signal reception, we recommend you purchase a signal amplifier for better picture quality.
How to Watch
Turn on TV to activate Auto Channel (See page 49) to memorize the available channels.
1
Press
Press
Press
INPUT on remote control.
2
3
4
to move to Analog TV or Digital TV and press
to select.
button or
button to select the desired channels.
Ex.) When you want to watch cable channel number 120, press
the digit buttons.
+
+
While watching digital broadcast, you can switch a digital signal to an analog signal by pressing the
button.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Watch Both Analog and Digital Broadcasts with Two Antennas
Connection Method
Connect an analog antenna to ANT 1 terminal for analog source and a digital antenna to ANT 2 terminal for digital
source. Please ensure to connect an antenna to a correct terminal. (If you connect an analog antenna cable to ANT
2, you cannot watch TV program.)
Digital TV antenna cable
Analog TV antenna cable
- When inserting a 75 ohm coaxial cable into the input connection, ensure the wire tip not to bend.
- If you experience poor signal reception, we recommend you purchase a signal amplifier for better picture quality.
How to Watch
Turn on TV to activate Auto Channel (See page 49) to memorize the available channels.
1
Press
Press
Press
INPUT on remote control.
2
3
4
to move to Analog TV or Digital TV and press
to select.
button or
button to select the desired channels.
Ex.) When you want to watch cable channel number 120, press
the digit buttons.
+
+
While watching analog broadcast, you can switch an analog signal to a digital signal by pressing the
button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Connecting the Video/Audio Connections to External Devices...
Please make sure to read the following information on connection to enjoy best picture quality.
Video/Audio connectors
Types of video/audio cable :
➀ HDMI / DVI-D ➁ 15-Pin D-Sub ➂ COMPONENT ➃ S-VIDEO ➄ COMPOSITE
Best picture quality is displayed in the following order.
The superior picture quality starts from the far left side.
- When connecting an external device, ensure to read the connecting device’s manual. The location or the number
of the terminals on the external device may be different depending on its model.
- Connect a HDMI (or DVI) connection to the output of DVD, cable receiver or satellite receiver. Connecting a
HDMI (or DVI) connection to a PC may result in a message, “Unknown Signal”.
- Do not power on until all necessary connections are made. If power is given before connections completed, this
may damage the product.
- Make sure to match the cable in color with the terminal.
- Make sure to check the type of terminals to be connected.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Connect a VCR/Cable Receiver
Connection Method
Connect the Video cable or S-Video cable between Video/S-Video output terminal of VCR or Cable receiver and
Video/S-Video input terminal of TV. (Connect the jacks to terminals in the same color.)
1
Connect the Audio cable (Left: white, Right: red) between Audio output terminal of VCR or cable receiver and
Audio input terminal of TV. (Connect the jacks to terminals in the same color.)
2
Video/Cable receiver
Audio cable
Video cable or
S-Video Cable
How to Watch
Turn on TV to press
on remote control.
1
Press
to move to Video or S-Video and press
to select.
2
For more information, read the user’s guide of VCR or cable receiver.
To enjoy better picture quality, use the S-Video cable rather than the composite cable.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect a DTV Receiver or DVD Player
Connection Method
Connect the Video cable (Y, Pb, Pr) between output terminals (Y, Pb, Pr) of DTV receiver or DVD player and the
input terminals (Y, Pb, Pr) of DTV/DVD (480i/480p/720p/1080i) on the rear of TV.
(Connect the jacks to terminal in the same color.)
1
Connect the Audio cable between Audio output terminal of DTV receiver or DVD player and Audio input
terminal for DTV/DVD Audio on the rear of TV. (Connect the jacks to terminals in the same color.)
2
DTV receiver / DVD Player
Video (Y, Pb, Pr) cable
Audio cable
How to Watch
Turn on TV and press
on remote control.
1
2
Press
to move Component 1 or Component 2 and press
to select.
For more information, read the user’s guide of DTV receiver or DVD player.
- Output terminal mark (Y, Pb, and Pr) of DVD player may be indicated as Y, B-Y, R-Y/Y-Cb-Cr /Y-Pb-Pr according
to the type of DVD player models.
- If your DVD player or Set Top Box supports HDMI (or DVI) /D-SUB, see Connecting to a PC (page 25) for
connection. You can enjoy more clear picture quality.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Connect a Camcorder/Game Player
Connection Method
Connect the Video/S-Video cable between Video/S-Video output terminal of Camcorder/Game player and
Video/S-Video input terminal of TV. (Connect cables and terminal in the same colors.)
1
Connect the Audio cable (Left-white, Right-red) between Audio output terminal of Camcorder/Game player
and Audio input terminal of TV. (Connect the jacks to terminals in the same color.)
2
Camcorder
Game Player
Audio cable
Video cable or
S-Video Cable
How to Watch
Turn on TV and press
on remote control.
1
2
Press
to move Video or S-Video and press
to select.
For more information, read the user’s guide of Game player or Camcorder.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect to a PC
Connection Method
Connect the PC signal cable (15-pin D-sub) between the output terminal of PC and the D-sub input terminal of
TV.
1
Connect the Audio cable between Audio output terminal of PC and Audio input terminal for PC on the rear of
TV. (Connect the jacks to terminals in the same color.)
2
Audio Cable
HDMI (or DVI) Cable
or
D-SUB cable
When Using as a PC Monitor
Turn on TV and press
on remote control.
1
2
Press
to move to PC or HDMI (or DVI) and then press
to select.
- If you use the HDMI (or DVI) connection, you can enjoy better picture quality.
- This product supports Plug-and-Play function.
- We recommend the above method if the DVD player or set top box supports DTV signal with HDMI (or DVI)/
D-Sub (15 pin) cable for the better picture quality.
- If you input an unsupported resolution in PC or HDMI (or DVI) mode, the screen won’t be displayed properly.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Resolutions Supported in PC
Resolution
Horizontal frequency
Vertical frequency
70.09
31.47
37.86
31.47
37.86
37.50
43.27
31.47
37.88
48.08
46.88
53.67
49.72
48.36
60.02
68.68
640 x 350
85.08
59.94
72.80
640 x 480
720 x 400
800 x 600
75.00
85.01
70.08
60.32
72.18
75.00
85.06
74.55
832 x 624
60.00
75.03
1024 x 768
85.00
26
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI Connection - For HDMI Model only
HDMI *1 (High Definition Multi media Interface) is the first all digital consumer electronics A/V interface that
supportsuncompressed standard. The HDMI terminal supports both video and audio information.To the HDMI*1
input terminal, you can connect an EIA/CEA-861/861B*2 compliant consumer electronic device, such asa Set
Top Box or DVD player with HDMI or DVI output terminal.Input a High-bandwidth Digital Content Protection
(HDCP) high-definition picture source to this HDMI terminal, so youcan display the high-definition pictures on
this TV in the digital form.
HDMI
DVD Player
If the external device has DVI
output only, use a DVI to HDMI
adapter *3 cable to connect to
Set Top Box
the HDMI terminal.
HDMI Cable
Compatible VIDEO Signal
Resolution
1080i
No. of dots(HXV)
1920 X 1080i
720 X 480p
Vertical scanning frequency(Hz)
59.94/60
59.94/60
59.94/60
59.94/60
480p
720p
640 X 480p
1280 X 720p
This input terminal is not intended for use with computers.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Compatible sampling freguency of AUDIO signal through HDMI (L.PCM) : 48kHz / 44.1kHz / 32 kHz
Notes:
• This HDMI connector is Type A.
• If you connect an equipment without a digital output terminal, connect to the COMPONENT VIDEO, S VIDEO or
VIDEO input terminal on the TV so you can enjoy an analog signal.
• The DIGITAL IN terminal can only be used with 1080i, 480i or 480p picture signals. Set the Digital Set -Top -
BoxDIGITAL OUT terminal Output setting to 1080i, 480i or 480p. For detailed information, refer to the Digital
Set -Top -Box instruction manual. If you cannot display the picture because your Digital Set -Top -Box does
not have aDIGITAL OUT terminal Output setting, use the component Video Input (or the S Video Input or Video
Input). In thiscase the picture will be displayed as an analog signal.
How to Watch
Turn on TV and Press
on remote control.
1
2
Press up/down button to move HDMI and press
to select .
- *1 HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMILicensing LLC.
- *2 EIA/CEA-861/861B profiles compliance covers profiles for transmission of uncompressed digital video
includinghigh bandwidth digital content protection.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect an External Visual Device
You can connect your TV to other visual device to watch two TV programs at the same time.
Connection Method
Connect the Composite Video cable between Video input terminals of an external device and the Video output
terminals for Video on the rear of TV.
(Connect the jacks to terminals in the same color.)
1
Connect the Audio cable between Audio input terminal (Left-white, Right-red) of an external device and Audio
output terminal for Video on the rear of TV. (Connect the jacks and terminals in the same color.)
2
For more information, read the user’s guide of an external device.
3
External Visual Device
Audio Cable
Video Cable
Video and Audio outputs are available only when watching an Analog TV, Digital TV or VCR. This is not supported
in the Input Mode of Component, HDMI (or DVI) /D-SUB or S-Video.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Use Digital Sound
Connection Method
Connect the coaxial cable or optical cable to the digital audio output terminal for coaxial cable or SPDIF
optical digital audio output terminal on the rear of TV.
1
2
3
Deselect Speaker Output from the Sound Menu and select Digital Sound Output. (See page 46~47)
For more information, read the user’s guide of the external sound device.
Do not look into directly the beam with the optical port. Doing so may damage your eyesight.
Amplifier with Built-in Dolby Digital AC3
Coaxial cable
or
Optical cable
Digital Audio Output is available when watching a digital TV program.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Select the Picture Mode
Users can automatically adjust the picture mode according to the input mode.
Press Menu button.
Menu items appear on the screen.
Press
button to select
1
2
“MODE” is selected.
Whenever you press Left or Right button, the mode
changes in following order.
Standard Dynamic Movie Mild
Custom 1 Custom 2
Press MENU button after the setting is done, and Menu goes
to the previous menu.
If the EXIT button is pressed, the menu disappears.
STANDARD : Most video contents are appropriate to this mode.
SPORT : Clear display
MOVIE : When watching a movie
MILD : Soft display.
CUSTOM : When the user wants to directly set the values See the next page
How to Directly Select Picture Mode :
Press MODE. button.
- When the input mode is Analog TV, Digital TV, Video, S-Video, Component 1 & 2, users can select Standard
Dynamic Movie Mild Custom 1/2 .
- When the input mode is PC, HDMI (or DVI), users can select Standard Low (Character Mode) High (Movie)
Custom 1/2 .
- When the input mode is Memory, users can select Standard Dynamic Movie Mild.
- The adjustment menu may be different depending on the input mode.
- The adjustment of Contrast, Brightness, Sharpness, Color and Tint is allowed only in the Custom mode.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Set the Desired Picture
Users can manually adjust their desired picture.
Press Menu button.
Menu items appear on the screen.
Press button to select
.
1
2
3
4
Press Left or Right button to choose “User 1/2”.
Press Left and Right buttons to move to Custom .
Press button to select Custom .
Picture Adjust menu items appear.
Press Up and Down buttons to move.
Press Left and Right buttons to adjust.
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
CONTRAST : Adjust the brightness and darkness of object and background.
BRIGHTNESS : Adjust the brightness of the entire picture.
SHARPNESS : Adjust clarity of outline of objects.
COLOR : Adjust colors into deeper or lighter colors.
TINT : Adjust colors naturally.
SHARPNESS, COLOR, TINT are not applied to PC and HDMI (or DVI) modes.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Adjust the Color Temperature of the Screen
Users can manually adjust their desired color temperature.
Press Menu button.
Menu items appear on the screen.
Press button to select
.
1
2
3
Press Up and Down buttons to move to “COLOR TEMP”.
Whenever you press Left or Right button,
the mode changes in following order.
Standard Warm 1 Warm 2 Cool 1 Cool 2
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears
STANDARD : General color of the picture
COOL 1, 2 : Cool color in the background with a bluish tint
WARM 1, 2 : Warm color in the background with a reddish tint
33
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Select the Aspect Ratio
Users can manually adjust the size of the screen.
Press Menu button.
Menu items appear on the screen.
Press button to select
.
1
2
3
Press Up and Down buttons to move to ASPECT RATIO .
Whenever you press Left or Right button,
the mode changes in following order.
Wide Normal Panorama Zoom 1 Zoom 2
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
How to Directly Select the Screen Size : Press
The current screen size is displayed on the OSD menu.
button.
If you press the ASPECT button repeatedly, the screen size changes in following order
- Under Digital TV input : Users can select Wide Normal Zoom 1 Zoom 2 Auto.
- Under PC inputs : Users can select Wide Normal.
- Under HDMI (or DVI) inputs : Users can select Wide Normal Zoom 1 Zoom 2.
- Under other inputs : Users can select Wide Normal Panorama Zoom 1 Zoom 2.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO (This is applied in digital broadcasting input mode only.)
The screen size automaticaly changes according to a signal source received
(General broadcast 4:3, Wide broadcast 16:9)
WIDE
General broadcast picture is adjusted
to 16:9.
Normal
4:3 general picture size
Panorama
Picture size for panorama video
ZOOM 1
Picture enlarged to 16:9 format, letter
box format.
ZOOM 2
Zoom in 16:9 in vertical direction
35
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Watch the PIP
This function allows you to watch the PIP or DW mode.
Press Menu button.
Menu items appear on the screen.
Press
button to select
.
1
2
3
4
Press Up and Down buttons to move to PIP.
Press Left and Right buttons to select PIP.
The PIP Menu appears.
Whenever you press Left or Right button,
the mode changes in following order.
PIP SMALL PIP MIDDLE PIP LARGE
DW 1 DW 2 OFF
After setting Mode, go to STEP 5 if you need to set the
SOURCE for Sub-picture.
<PIP 1>
<PIP 2>
<PIP 3>
<DW 1 >
<DW 2 >
Continued on the next page
36
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Set the INPUT for the Sub-Picture
This function is available only in the PIP mode.
Press Up and Down buttons to move to SOURCE
5
Press Left and Right buttons to select SOURCE .
The list of sub-picture sources appears.
6
Press Up and Down buttons to move to the sub-picture
source you want.
7
Press Press button to select source.
8
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
You can set the PIP mode quickly using the remote control.
How to Select the PIP : Press the
Whenever you press this button, the PIP mode is selected or deselected.
How to Select the Size of Sub-picture : Press the button.
Whenever you press this button, the size of the Sub-picture changes.
How to Select the INPUT : Press the button.
Press the buttons to select the INPUT and then select
How to Switch the PIP to Sub-picture : Press the
button.
.
button.
Whenever you press this button, the Main picture and Sub-picture are switched each other.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Set the channel of the Sub-picture Channel : Press the
This is applied only when the sub-picture is displayed.
How to Change the Position of the Sub-picture : Press the
button.
button.
Bottom Right Corner Bottom Left Corner Left Top Corner Right Top Corner
The same input mode cannot be selected for the main picture and sub-picture.
Supported PIP Table
PIP : O → Supported, X → Not Supported
Sub
PC
HDMI(or DVI)
DTV
Component 1 Component 2
Analog TV
Video
S-Video
Main
PC
X
X
X
X
X
X
X
X
O
O
O
X
X
X
X
X
X
O
O
O
X
O
O
O
X
X
X
X
O
O
O
X
X
X
X
X
O
O
O
X
X
X
X
X
O
O
O
X
HDMI(or DVI)
DTV
O
O
O
O
X
O
O
X
O
O
O
O
O
X
O
X
O
O
O
O
O
O
X
X
Component 1
Component 2
Analog TV
Video
S-Video
Memory
38
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Noise Reduct
Press Menu button.
Menu items appear on the screen.
Press button to select
.
1
2
3
Press Up and Down buttons to move to NOISE REDUCT .
Whenever you press Left or Right button,
the mode changes in following order.
LOW HIGH Off
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
In the Noise Reduction, the more you reduce the screen noise, the more the sharpness level of the pictures
may become degraded.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Select the Audio Mode
Users can adjust sound mode automatically as they want.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
Press button to select
.
2
3
MODE is selected.
Whenever you press Left or Right button,
the mode changes in following order.
Standard News Music Sport User
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
STANDARD : General sound mode. This fits most audio contents.
NEWS : For enjoying clear sound.
MUSIC : For enjoying original sound.
SPORTS : For enjoying vivid sound.
CUSOTM : When the user wants to set the value. See the next page
How to Directly Select Sound Mode :
Press MODE. button.
Users can select Standard News Music Sport Custom .
40
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Adjust the Desired Audio Mode
Users can adjust sound mode automatically as they want.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
5
Press button to select
.
Press Left and Right buttons to select USER .
Press Up and Down buttons to move to CUSTOM .
Press Left and Right buttons to select CUSTOM .
SOUND CUSTOM menu appears.
Move between the items listed using UP or Down button.
Adjust the level of the item selected using Left or Right button.
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
VOLUME : Adjusts the volume.
BASS: Adjusts the range size of low sound.
TREBLE: Adjusts the range size of high sound.
BALANCE : Adjusts the balance of left and right speakers.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Use the Automatic Volume Control
With this Automatic Volume Level Control, everything you watch will always maintain the volume level that you
decide.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
Press button to select
.
Press Left and Right buttons to set to ON/OFF .
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Select MTS(Multi-Channel Sound)
Depending on the particaular program being brodcast, you can select stereo, mono, or a Separate Audio
Program. (SAP audio is usually a foreign-language translation. Somtimes SAP has unrelated information like
news or weathter.)
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
Press
button to select
.
Press Up and Down buttons to move to
“MTS”.
Press Left and Right buttons,
Repeatedly to select “MONO”, “STEREO” or “SAP”.
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
How to Directly Select MTS : Press the
button
Repeatedly to select “MONO”, “Stereo” or “SAP”.
- Choose “Stereo” for channels that are broadcasting in STEREO.
- Choose “MONO” for channels that are broadcasting in MONO, or if you are having difficultly receiving a STEREO
signal.
- Choose “SAP” to listen to the seperate audio program, which is usually a foreign-language translation.
* You can select one of the languages listed you prefer when you watch a digital program that is supported with foreign
language.
If you also press the MTS button on remote control unit under other mode than TV mode, the current setting
information is displayed. If you press the MTS button twice, the mode shifts MONO STEREO in order.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Listen to SRS TruSurround XT (Surround)
Users can enjoy spectacular 3D sound.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
Press button to select
.
Press Up and Down buttons to move to SURROUND .
Press Left and Right buttons to set to ON/OFF .
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.
The SRS TruSurround XT function is activated only when the audio input signal is Stereo.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Set the Output of Subwoofer
You can set this function when you wish to install your subwoofer system.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
5
Press button to select
.
Press Up and Down buttons to move to “SUB WOOFER .
Press Left and Right buttons to select “SUB WOOFER .
SUB WOOFER menu items appear.
Choose one of the items listed. Press Left and
Right buttons to adjust.
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
- The frequencies in the entry are the subwoofer’s frequency range.
- You make sure to use a subwoofer speaker system with built-in amplifier.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Set the Speaker Out
If you wish to use an external audio system, you can turn off the TV speakers.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
Press button to select
.
Press Up and Down buttons to move to SPEAKER OUTPUT .
Press Left and Right buttons to select ON/OFF .
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Set the Digital Audio Output
The digital audio output terminal allows you to enjoy digital sound. (For more details, see page 30)
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
Press button to select
.
Press Up and Down buttons to move to
“DIGITAL AUDIO”
Press Left and Right buttons to select ON/OFF.
Whenever you press Left or Right button, the mode shifts in following order.
Dolby PCM OFF
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
Manufactured under license from Dolby Laboratories.
°∞Dolby° and the double-D symbol are trademarks of Dolby Laboratories.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Set Audio Language
While watching a digital program, you can listen to foreign language if the program is supported with foreign
language.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
Press button to select
.
Press Up and Down buttons to move to AUDIO LANGUAGE .
Whenever you press Left or Right button,
the mode shifts in following order.
ENGLISH SPANISH FRANCE
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
How to Directly Select Audio Language : Press the
button.
- Whenever you press this button, the mode shifts MONO STEREO SAP in order when receiving analog
signals.
You can select one of the languages listed you prefer when receiving digital signals.
- If you want to see language information while watching a digital channel, press the
language information that is currently received.
button to display
48
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Store Channels Automatically
- Your TV can memorize and store all of the available analog/digital broadcast signals for both “off-air”
(antenna) and cable channels.
- Before your television can begin memorizing the available channels, make sure to specify the type of the
signal source (antenna or cable) connected to your TV.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
Press button to select
.
AUTO STORE is highlighted.
Press button to select “AUTO STORE”.
AUTO STORE menu items appear.
Press Left and Right buttons to select the type
of antenna connection.
- In case of ATV/DTV (ANT1) :
When watching both analog broadcast and digital
broadcast at the same time with ANT1
Press Up and Down buttons to move to AIR TV or CATV.
• AIR ONLY : Watching the analog over-the-air and
digital over-the-air signals via ANT1 input port.
• CABLE ONLY : Watching the Cable and digital cable
signals via ANT1 input port.
5
6
- In case of ATV (ANT1) + DTV (ANT2) :
When watching analog broadcast with ANT1 and digital broadcast with ANT2.
Press Up and Down buttons to move AIR + AIR, AIR + CABLE or CABLE + AIR.
• AIR(ANT1)+AIR(ANT2) : Watching the analog over-the-air via ANT1 input port and the digital
over-the-air signal via ANT2 input port.
• AIR(ANT1)+CABLE(ANT2) : Watching the analog over-the-air via ANT1 input port and the digital
cable via ANT2 input port.
• CABLE(ANT1)+AIR(ANT2) : Watching the analog cable via ANT1 input port and the digital over-
the-air via ANT2 input port.
Press Left and Right buttons to set up CABLE BAND.
*CABLE BAND NOTE : STD (Standard), HRC (HRC band), IRC (IRC band)
(For further band information, contact your cable service provider.)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Press button.
AUTO SCAN is activated.
7
- In the middle of AUTO SCAN, if you press button once, analog AUTO SCAN is interrupted. If you press
button a second time, digital AUTO SCAN is interrupted. Press the Menu button to exit. Then the original
channel is returned.
- If you have changed the connection of an antenna or cable, perform AUTO SCAN again.
How to Add/Erase Channels Manually
Users can add or erase the desired channels.
Press
\
schannel buttons or the number buttons
on remote control to view all channels that will be
added or erased.
1
2
3
4
5
Add or erase channels by pressing the
ADD/ERASE button.
Press Left and Right buttons to set ADD/ERASE .
Press Up and Down buttons to move to YES/NO .
Press button to set.
When you wish to restore any digital channels that have been deleted, you need to perform AUTO SCAN again.
If you want to directly use the number buttons for storing, contact your local broadcasting company or cable
company for the required channel digits. Unlike an analog broadcast, a digital broadcast uses virtual channels,
not fixed channels. For more information on virtual channels, see page 65.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Set Favorite Channels
Users can store frequently watched channels to quickly access a preferred channel.
- How to store the channel you are currently
watching as a favorite channel
Press “BOOK-MARK” button.
Then the channel will be stored while Favorite Channel
Selected is displayed on the screen.
- How to access the stored favorite channel
Press FAVORITE button.
You can access the favorite channel by pressing
this button repeatedly.
- How to deselect a favorite channel
Display the channel to be deleted on the screen and
then press the BOOK-MARK button twice.
The stored channel is deleted while Favorite Channel
Deselected is displayed on the screen.
The Favorite function is available only with remote control.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Fine Tune Channel Reception
If the reception is clear, you do not have to fine tune channels, as this is done automatically during the search
and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
5
Press button to select
.
Press Up and Down buttons to move to “FINE TUNE”.
Press button to select “FINE TUNE”.
FINE TUNE menu items appear.
Press Left and Right buttons to adjust the screen.
The displayed channel digit is the channel
that is currently viewed.
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
The selected OSD for fine tuned channels is highlighted in orange.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
How to the LNA (Low-Noise-Amplifier) Feature
If the reception is clear, you don’t have to use this feature.
If the signal is weak or distorted, perform the following steps.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
Press button to select
.
Press Up and Down buttons to move to “LNA”.
Press Left and Right buttons to set to ON/OFF .
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Choose Your Language
Users can select their language preference in order to display main menus and sub menus, etc.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
Press button to select
.
LANGUAGE is highlighted.
Whenever you press Left or Right button,
the mode shifts in following order.
ENGLISH FRANÇAIS ESPAÑOL
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Set Clock, On/Off Time, Sleep Time
- You can automatically turn on or off the TV at a preset time. To do this, you must set the clock if you wish to use the
automatic on or off timers.
- No Signal Timeout allows you to automatically turn off the TV if there is no broadcast signal for a certain period of time.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
5
6
7
8
9
Press
button to select
.
Press Up and Down buttons to move to “TIME”.
Press button to select “TIME”.
The CLOCK items appear.
- To set the Current Time :
Press Left and Right buttons to move between Hour,
Minute and AM/PM and Press Up and Down buttons to
set Hour, Minute and AM/PM.
After the setting is done, you can set WAKE UP and OFF TIMER.
- To set the WAKE UP :
Press Left button to exit the item and
press down arrow button to move to WAKE UP.
Press
button to select and press Left/Right and
Up/Down buttons to move between items or set each item.
- To set the OFF TIME :
Press Menu button to exit and
press the down arrow button to move to OFF TIME.
Pres Left and Right buttons to move to the items and
Press Up and Down buttons to set each item (See step 5)
Continued on next page.....
55
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Continued from previous page..... (Set the SLEEP TIMER and NO SIGNAL TIMEOUT)
- To set SLEEP TIMER :
Press Left button to exit and press the down
arrow button to move to “SLEEP TIME”.
10
11
12
13
Whenever the Left or Right button,
the mode shifts in following order.
30 60 90 120 240 OFF
- To set NO SIGNAL TIMEOUT :
Press Up and Down button to move to “AUTO OFF”.
Press Left and Right button to select ON/OFF .
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
How to Directly Set the SLEEP TIMER : Press
Whenever this button, the mode shifts 30
button.
90 120
60
240
OFF
in order.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Set the Geometry in PC Mode
This function is only available in PC mode.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
5
Press button to select
.
Press Up and Down buttons to move to “IMAGE ADJUST”.
Press button to select “IMAGE ADJUST”.
Then the IMAGE ADJUST items appear.
Press Up and Down buttons to move to items you want.
Press Left and Right buttons to adjust.
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
H. POSITION : To adjust the horizontal position of the picture.
V. POSITION : To adjust the vertical position of the picture.
FREQUENCY : To eliminate the picture noise.
PHASE : To eliminate the shake of picture.
How to Directly Adjust the Picture : Press the
button.
The picture will be automatically optimized for viewing.
If the display input signal (resolution) has been changed, the picture will be automatically optimized.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Set Key Lock
This function is used to prevent from using the control buttons on the front top of the TV or from connecting
external devices to the TV. You make sure to set a PIN number to use this function.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
5
6
7
8
9
Press button to select
.
Press Up and Down buttons to move to “LOCK”.
Press button to select “LOCK”.
Then the Enter PIN number window appears.
The default is 4 digits (0-0-0-0).
Press the numeric keys to enter your PIN number.
The LOCK items appear.
Press button to select “CHANGE PIN”.
Then the Enter PIN number window appears.
Enter a 4-digit PIN number.
When the Confirm PIN number window appears,
enter the PIN number again.
- To set Key Lock :
Press Up and Down buttons to move to “KEY LOCK”.
Press Left and Right buttons to set to ON/OFF .
When setting to ON, the control buttons on the
front top of the TV will be engaged.
Continued on next page ......
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Continued from previous page..... (Set the Lock External Signal function.)
- To set Aux Block :
Press Up and Down buttons to move to
“AUX BLOCK”.
10
Press button to select “AUX BLOCK”.
Then the AUX BLOCK items appear.
11
Press Up and Down buttons to move to the item you want.
Press Left and Right buttons to set to ON/OFF .
If the item is set to ON, such item is disabled.
12
Press MENU button after the setting is done, and Menu
goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
- The Lock External SIGNAL function is designed to prevent a VCR or game player from being connected to the TV.
- If you forgot your PIN number, press the MENU + MTS + SLEEP + DISPLAY buttons on the remote control in
sequence to restore the default number, 0-0-0-0.
- The Key Lock function will be disengaged when you turn off and then on AC power or when a power failure
happens.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How To Set Block Program
This(V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station.
The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by
the categories chosen to be blocked.
V-Chip rating and categories
Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be
blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-
video movies use the Movie Rating System (MPAA) only.
Ratings for Movies previously shown in theaters :
Movie Ratings : - Blocking Off
(Permits all programs)
(General audience)
- G
- PG
(Parental guidance suggested)
(Parents strongly cautioned)
(Restricted)
- PG-13
- R
- NC-17
- X
(No one 17 and under admitted)
(Adult only)
If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.
Ratings for Television programs including made-for-TV movies :
- TV-G
(General audience)
- TV-PG
- TV-14
- TV-MA
- TV-Y
(Parental guidance suggested)
(Parents strongly cautioned)
(Mature audience only)
(All children)
- TV-Y7
(Children 7 years older)
TV Rating Children : - Age
- Fantasy Violence
(applies to TV-Y, TV-Y7)
(applies to TV-Y7)
TV Rating General : - Age
- Dialogue-sexual dialogue
(applies to TV-G, TV-PG, TV-14, TV-MA)
(applies to TV-PG, TV-14)
- U Language-adult language (applies to TV-PG, TV-14, TV-MA)
- Sex-sexual situations
- Violence
(applies to TV-PG, TV-14, TV-MA)
(applies to TV-PG, TV-14, TV-MA)
Continued on next page ......
60
Download from Www.Somanuals.com. All Manuals Search And Download.
...... Continued from previous page.
Press Menu button.
Menu items appear on the screen.
1
2
3
4
5
6
7
8
9
Press Up and Down buttons to move to
icon
and press
buttons to select.
The message “Enter PIN” will appear.
Enter your 4-digit PIN number.
The new screen will appear.
Press Up and Down buttons to move to
“BLOCK PROGRAM” and press
The new screen will appear.
buttons to select.
Press Left and Right buttons to “ON”.
Press Up and Down buttons to move to
“TV-Guide” or “MAPP”.
Press button to select
“TV-Guide” or “MAPP”
The new screen will appear.
Press Up and Down or Left and Right buttons to
choose items.
TV-guide menu screen
Press Up and Down buttons to select
“U” or “B”
(U=Unblock, B=Block)
Press MENU button after the setting is done,
and Menu goes to the previous menu.
MAPP menu screen
If the EXIT button is pressed, the menu disappears.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to View Closed Captions
Choices in the closed caption menu are : CC Mode, Priority (Analog caption or Digital caption), and Option.
1. CC MODE :
ON : Captioning information is always shown, when available.
OFF : No captioning information is displayed.
On mute : Captioning information is only when the TV's sound is mute, when available.
(To mute the sound, press the mute button on the remote control and captioning information will appear on the
screen, if available)
If you turned off the speakers in the Audio menu, closed captioning won’t appear when you press the mute
button on the remote.
2. PRIORITY :
You can choose whether the TV uses digital or analog captions for digital TV programs that have both or either.
- ANALOG (CAPTION) : You can select a closed caption mode, which is the mode, or source, used for displaying
captioning information for analog channels or digital channels, if available.
• CAPTION :
The form for the words that scroll across the bottom of the TV screen : usually the audio portion of the program
provided for the hearing impaired.
CC 1
: For video related information that can be displayed. Script can be in any language.
CC 2/3/4 : Other modes used for video related information.
• TEXT :
The term for the words that appear in a large black frame and almost cover the entire screen :
Usually message provided by the broad caster.
T 1
: Blanks out a large portion of the picture on the television screen, and display program guide or any
other information currently being transmitted.
T 2/3/4 : other modes that display information and blank out a large portion of the picture of the TV screen.
- DIGITAL (CAPTION) : You can select a closed caption, service mode(1-7) for digital channels.
The service modes support MPEG-2 based transport sources Service 1 and Service2 are the
primary and secondary languages, respectively.
Service3 and service4.5.6 are additional caption sources that may be available.
Continued on next page ......
62
Download from Www.Somanuals.com. All Manuals Search And Download.
...... Continued from previous page.
3. OPTION :
Customized closed captioning for the digital caption by choosing the settings for the following options :
SIZE : Set the size of the words - AUTOMATIC -> STANDARD -> LARGE -> SMALL.
TEXT COLOR : Chose a color for the text - AUTOMATIC -> WHITE -> BLACK -> RED -> GREEN -> YELLOW
-> MAGENTA -> AND CYAN.
TEXT OPACITY : Specify the opacity for the text color - AUTOMATIC -> SOLED -> TRANSPARENT -> TRANSLUCENT.
BG(BACKGROUND) COLOR : Select a background color - AUTOMATIC -> WHITE -> BLACK -> RED -> GREEN ->
YELLOW -> MAGENTA -> CYAN.
BG OPACITY : Specify the opacity for the background - AUTOMATIC -> SOLED -> TRANSPARENT -> TRANSLUCENT.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
and press buttons to select.
icon
1
2
3
4
5
6
Press Up and Down buttons to move to
“CLOSED CAPTION” and press buttons to select.
Closed Caption menu appear.
CC MODE is highlighted.
Press Left and Right buttons to select “ON” or ON MUTE”.
Sub menu items are activated.
Press Up and Down buttons move between the items
Press Left and Right buttons to select the item.
When selecting the Option item, press
Option menu appear.
button.
Press Up and Down buttons move between the items
Press Left and Right buttons to select the item.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Use the Current Channel Guide
Users can get information on broadcasting time and signal status of the current digital channels.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
and press button to select.
1
Press button again to select
the “CURRENT CHANNEL Guide”.
The information on broadcasting time and signal status, etc.
2
of the channels your are currently watching will be displayed.
How to Directly Use the Current Channels : Press the
button.
How to Reserve TV Programs Using the Total Channel Guide
- Users can get the broadcasting time information of all the entire digital channels. To do this, it is required to
set the current time first.
- The displayed broadcasting time may be different from that provided by your local broadcasting company.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
1
and press button to select.
Press Up and Down buttons to move to
“TOTAL CHANNEL GUIDE”.
2
Press button to select “TOTAL CHANNEL GUIDE”.
3
The broadcasting time and related information
of all channels will be displayed.
To schedule TV programs,
go to step 4 on the next page.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use TV Program Reservation
If you have scheduled a TV program you are going to watch, the channel you are currently watching is
automatically switched to the scheduled channel, or when your TV is in stand-by, the scheduled TV program is
on at the defined time. If the AC power is off, this function is deactivated.
Continued from previous page.
Press Up/Down and Left/Right buttons to move to a
TV program to be scheduled.
4
Press
button.
5
6
7
A window “Will you schedule this program?” appears.
Press Left and Right buttons to move to YES ,
if you want to schedule. If you don’t want to schedule,
move to NO .
Press button to set.
If scheduled, the program title is highlighted in red
and if scheduling is cancelled, the red disappears.
You can check a listing of scheduled programs from the
SCHEDULE LIST menu. For more details, see the next page.
Press MENU button after the setting is done, and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
How to Directly Select the Entire Channel Information : Press the
button.
- You can schedule up to five TV programs at a time.
- When a scheduled TV program starts to broadcast, the program is automatically removed from the listing.
- You can schedule only TV programs on the air within 24 hours. This schedule keep updated. For example, if the
current time is AM 10:00, any programs you want to schedule is allowed until AM 10:00 next morning.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
How to Check or Cancel a Scheduled TV Program
Users can look through scheduled TV programs or remove a scheduled program from a listing of scheduled
programs.
Press Menu button.
Menu items appear on the screen.
Press Up and Down buttons to move to
.
1
2
3
4
5
6
7
8
Press button to select
.
Press Up and Down buttons to move to “RESERVATION LIST”.
Press button to select “RESERVATION LIST”.
The Reservation List will appear.
- To remove a scheduled program :
Press Up and Down buttons to the program
you want to remove.
Press button.
A windowWill you remove this program? appears.
Left and Right buttons to select YES .
Press button to remove the item.
Press MENU button after the setting is done,
and Menu goes to the previous menu.
If the EXIT button is pressed, the menu disappears.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use Memory Mode
Please read the following instructions carefully before use. - For Q320/Q400 Model only
Precautions when using a Memory Card
Ensure to use a memory card labeled with the manufacturer’s name and manufacture number.
Do not insert other objects such as a coin than a memory card into the memory card slot, which may cause a
malfunction.
Do not drop or apply a shock to memory cards.
Keep a memory card in the provided case after use.
Do not dismantle or modify memory cards.
Avoid static electricity or electronic noise as this may damage data stored in a memory card.
We cannot be liable for misuse of the TV set, any troubles during use, or other problems, or incorrect settings,
except for those cases for which we are liable by law.
Any damages arising out of the misuse of the TV set may result in damage to or loss of data.
We are not responsible for any damaged data. To avoid this, ensure to back up an important file.
This unit is designed for you to listen to personally converted MP3 files for personal use only. Also, when listening
to any copyright-protected files, ensure to use a separate MP3 player.
Precautions when inserting a memory card
Turn the TV set off before connecting all necessary cables.
Insert a memory card with the label facing up avoiding twisting or skewing.
Insert a memory card with the label facing up and the arrow on the label pointing toward the unit. Inserting the
memory in upside down may result in damage to the memory card or unit.
Do not attempt to remove a memory card while it is in operation. This may cause serious damage to the memory
card or unit. Ensure to stop all memory cards before removing a memory card from the unit.
Make sure the cards are completely and firmly inserted into the appropriate slots.
Improperly seated cards will cause serious damage to memory cards or unit.
Make sure the RSMMC, miniSD, T-FLASH, MS Duo and MS Pro Duo memory cards
are inserted into an adapter. Contact the dealer where your memory card is
purchased.
Adapter
Commercially available memory cards (Sold separately)
- The available types of memory cards by slot are shown on the side of the TV.
- The playback speeds vary depending on the memory card types.
Memory Card Slot 1 (MT)
Memory Card Slot 2 (CF)
67
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Supported Files
CompactFlash : 8MB ~ 4GB
Microdrive : 1GB, 2GB, 4GB / 2.5GB, 5GB
SmartMedia : 8MB ~ 128MB
Using a memory card with capacity
larger than the unit is capable of
supporting may cause an error.
Available
memory card
capacity
xD-Picture : 16MB ~ 512MB / 1GB(M-CARD)
MultiMediaCard/RS MMC : 8MB ~ 1GB
Secure Digital/miniSD : 8MB ~ 1GB
A very high capacity of a memory card
may result in slow speed.
Some non-supported Jpeg or MP3 files
may not be played back.
Memory Stick/Duo : 4MB ~ 128MB
Memory Stick Pro/Duo : 256MB, 512MB, 1GB
USB HDD, Flash Memory Bar
MP3 Player (Available only in portable disk mode)
Cellular Phone (Available only in portable disk mode)
USB 1.1
HOST
USB HOST
Make sure to use TV USB power for USB HDD with 2.5” or less. Never use
separate power.
Make sure to use separate power for 3.5” USB HDD.
Power
Supply
Supported Media File Types
JPEG : JIFF, EXIF (.jpg)
Support
Photo
Baseline JPEG : 5120x3840 (Max. Resolution)
Progressive JPEG : 2048x1536 (Max. Resolution)
Compatibility
DivX3, DivX4 XviD (.avi) MPEG-1 (.mpeg/.mpg)
MPEG-2 (.mpeg/.mpg/.vob) MPEG-4 (.mpeg/.mpg, asf)
Support
DivX - 720 x 480 30fbs or less, - 720 x 576 25fbs or less
- AC3 support, MPEG-1 audio layer-2 and 3 encoded files
- GMC(Gobal Motion Compression), Q-Pel(Quarter Pixel) not supported.
MPEG-2 - Main prolile@Main level, - 2Mbps below supported
MPEG-4 - 640 x 480 (4Mbps or less), - MPEG-4V1 : not supported
- MPEG-4V2 : Simple Profile supported.
Movie
Music
Compatibility
Motion JPEG(.avi) - 640 x 480 15 frames/sec
Support MP3
Compatibility ID3 tag not supported
MP3i, MP3 PRO not supported
Supported Compressed Jpeg/Image File Format
Compression method
Color format
Standard
(Baseline)
Optimization
(Progressive) 11:11:11(Y,Cb,Cr)
4:4:4
4:2:2, 21:11:11(Y,Cb,Cr)
12:11:11(Y,Cb,Cr)
4:2:0
22:11:11(Y,Cb,Cr)
JPG compression
Image display
O
O
X
O
O
Image
Image
Not supported
Image
Image
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Memory Card
1. Insert a memory card or USB memory into Slot 1/2 or USB port.
2. Press
3. Press
to power on.
to select Memory Mode.
Memory Card Slot 2 (CF)
4. Refer to icons listed below menu screen to manipulate.
CAUTION !
When you are going to remove the memory card, press the
button on the remote control. You can go back to the
initial screen anytime to remove the memory card safely
while keeping the damage to stored data to a minimum level.
If you have pressed the EXIT button, you have to remove and
then insert the memory card or turn the power off and on to use
the memory card. Otherwise, a message No device will
appear when selecting.
Memory Card Slot 1 (MT)
Only one memory card is allowed for each slot.
Shifting into Memory Mode
Memory Mode allows you to play back photos, music, movies and motion pictures files that are stored in memory
cards.
When selecting a slot into which no memory card is inserted, a message, No device will appear.
Move one of the slots you want.
The initial screen of the memory mode will appear.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Viewing the stored photo files
Current page/All pages
Preview
Mode
Card type/capacity
Manipulation buttons
Viewing full-size photos
1. Press
to move a photo file you want.
Press
to select.
To the icon menus, press the
button.
1) JFIF
- As decording is required when making a listing,
decording time is different according to file sizes.
- While the slide show is in operation, music may be
paused temporarily or corrupted according to the
performance of the memory card or USB device.
2) EXIF
Listed files are quickly displayed when making a listing.
This is because EXIF files that have been created by a digital camera, etc. contain already listings.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing full-size photos
Whenever you press
from the current screen, magnifying powers are shifted in sequence 1.5X 2X 2.5X
1X(original size).
After zooming in a photo, press
to move.
Rotating a photo
To rotate the photo by 90 degrees clockwise, press
button. To rotate the photo by 90 degrees
counterclockwise, press button.
Viewing images using Slide Show
1. Press
to display Option Menu.
2. Press
and press
to move between items
to change.
FAST MEDIUM SLOW
3. After setting, press
buttons to move to PLAY.
RANDOM TOP->BUTTOM CENTER->LEFT/RIGHT
LEFT->RIGHT (BLIND) CLOSS FADE
Press
to start a slide show.
ON OFF
Slow access may take place according to file sizes, selected effect mode and card types (MMC/MS) or due to
unsupported image files. This may result in difference in time taken to display images or corrupted music sound.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Viewing the stored music files
Artist/File size
Selected file/All files
Mode
Card type/Capacity
File name/Playing time
Manipulation buttons
When you press
, the slide show function
starts playing back music files according to the
selected options in photo mode.
ModeaMusic file name
File information
Playing back music files
1. Press
to display Option Menu.
1. Press
to play back.
Whenever you press
Repeat 1 Repeat All Play Sequence.
When you press
you can listen to music in power saving mode.
, you can set
Playing time
Manipulation buttons
,
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the stored movie files
Playing time/File creation date
File order/All files
Playback mode
Mode
File name/Playing time
Card type/Capacity
Manipulation buttons
You can set to play back all files (Play Sequence) or selected file (Play One)
in sequence by pressing
.
Playing back movie files
1. Press
to move to movie file you want.
2. Press
to select a movie file to play back.
To hide the icon menus on the bottom of the screen,
press
.
To perform Rewind or Fast Forward, press
.
To pause, press
.
To see running time, press
(BROADCAST).
73
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
- Slow access may take place according to card types (MMC/MS). This may result in interruption of a motion
picture being played back.
- When playing back a motion picture stored in a USB memory, an interruption may take place. This
phenomenon is not because the product yields its low performance but because the transmission speed differs
depending on the USB memory types.
Checking the stored movie files
Card type/Used space/Total capacity
File order/All files
Mode
Card type/Capacity
File name/File creation date
Manipulation buttons
Running a file
1. Press
to move to a file you want.
If you select, in Photo Mode, Music Mode or Movie Mode, one of the
non-executable files or unrecognized files stored in the memory
card, an error message, “No file in this mode” will appear.
2. Press
to run.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use an External Device Using the Remote Control
When setting other manufacturer s product using the remote control, some of the buttons on the remote control may
not operate or different functions may be activated, or some of other manufacturer s products may not work. Some
of DVD/VCR combos are allowed only either in DVD mode or VCR mode.
1. Turn on the external device you want to set.
2. Whenever you press
VCR DVD CATV
button on the remote control, the mode shifts
in order.
TV
3. If the external device has been chosen, press the
at the same time for two seconds.
button and
button
4. Enter an appropriate 3-digit number of the manufacturer from the DVD Setting
Number Table. (If the product brand you want to set has multiple setting numbers,
attempt to enter the setting numbers repeatedly until the product is turned off.)
5. When the product has turned off, press the
button again.
(The appropriate button associated with the product will flash 3 times to show the
product operates properly.)
6. Check that the Power button works normally and then check that other function
buttons work normally.
If the Power button works normally but other function buttons do not, repeat the
above steps from the beginning.
Depending on product brands or setting numbers, the power button may work
normally but other function buttons do not work.
VCR Setting Number Table
75
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
DVD Setting Number Table
76
Download from Www.Somanuals.com. All Manuals Search And Download.
AMP Setting Number Table
CATV Setting Number Table
77
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Glossary 1
Component video Component video is sent through three cables: two color shade (chrominance) signals
and one brightness (luminance) signal. Component video achieves greater color
accuracy than composite video or S-VIDEO by splitting chrominance into two separate
portions.
Composite video Composite video is sent through a single cable. Composite video combines the color
shade (chrominance) and brightness (luminance) information into one video signal.
S-VIDEO S-VIDEO requires a single cable, which carries the brightness (luminance) and color
(chrominance) signals of the picture separately. S-VIDEO provides better resolution
than composite video, which carries the signals together.
480i Provides 480 lines of resolution. Displays images using interlaced scanning, which first
transmits all the odd lines on the TV screen and then the even lines.
480p Provides 480 lines of resolution. Displays images using progressive scanning, which
transmits each line from top to bottom.
720p Provides 720 lines of resolution. Displays images using progressive scanning, which
transmits each line from top to bottom.
1080i Provides 1080 lines of resolution. Displays images using interlaced scanning, which
first transmits all the odd lines on the TV screen and then the even lines. 1080i is one
of the formats used by HDTV (High Definition TV).
Digital television (DTV) A new technology for transmitting and receiving broadcast television signals. DTV
provides higher resolution and improved sound quality over analog television.
HDTV(High Definition TV) HDTV is a new kind of digital TV, creating a high quality picture, high definition. The
HDTV provides a theater-like screen with an aspect ratio of 16:9. Supports 720p or
higher.
SDTV(Standard Definition TV) SDTV is a new kind of standard definition digital TV, having a range of lower resolution
than the HDTV. Supports 480i.
Cable Broadcast Receiver A device that receives cable broadcasting. Connecting it to your TV set allows you to
watch a various channels.
(Converter)
Satellite Broadcasting Provides crisp picture and clear audio quality throughout the country via a satellite.
VHF/UHF VHF (Very High Frequency) is the part of the frequency spectrum from 30 to 300
megahertz. UHF (Ultra High Frequency) is the part of the frequency spectrum from 300
to 3,000 megahertz.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 2
DVD DVD (Digital Versatile Disc) is an optical disc that can store a huge volume of
multimedia such as video, game, and audio application, etc.
Coaxial Cable Coaxial cable is the kind of rounded copper cable, which is generally used for TV
antenna.
LNA (Low-Noise-Amplifier) Satellite applied technology. It is capable of amplifying weak signals so that any area
experiencing a signal interruption may enjoy a clearer picture quality.
Aspect ratio Refers to the ratio between the width and height of the screen. This TV has a 16:9
(widescreen) aspect ratio, as opposed to a 4:3 aspect ratio.
PIP (Simultaneous Screen) PIP allows you to view two images at the same time in a single screen.
SWAP PIP function provides a main picture (larger image) and sub-picture (smaller image).
The SWAP is designed to swap the sub-picture for the main picture. For example,
while you are watching a main picture on TV and watching a sub-picture on VCR, you
can instantly switch the two pictures by using the SWAP function.
Picture Mode Picture Mode features the optimal picture quality. There are Standard-Dynamic-Movie-
Mild- Custom features in order. “CUSTOM” allows you to adjust Contrast, Brightness,
Sharpness, Color and Tint.
Sound Mode Sound Mode features the optimal sound quality. There are Standard-News-Music-
Sports- Custom features in order. “CUSTOM” allows you to adjust high frequency
sound, middle frequency sound and low frequency sound.
Digital Broadcasting Video and Audio signals digitized and transmitted by broadcasting companies
complying with the new digital television standard developed by the ATSC (Advanced
Television System Committee). Digital Broadcasting technology provides multimedia
services including a variety of additional services as well as high-definition quality
picture.
Analog Broadcasting ATSC-based Video and Audio signals transmitted by broadcasting companies.
SRS TruSurround TX A well-recognized 3D sound technology developed by US SRS Labs, Inc.
This technology delivers the ultimate audio experience only with two speakers as if
through multi-channel speakers.
Dolby Digital Formerly known as AC-3, Dolby Digital is a digital audio coding technique that reduces
the amount of data needed to produce high quality sound.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Glossary 3
Subwoofer Designed to improve ultra low frequency with about 150Hz. There are active type that
is built with a built-in amplifier and passive type that is required to connect an
additional amplifier to it.
Mono Audio signals are produced through a single channel. It is difficult to experience a
spectacular sound since audio signals are reproduced with a single speaker.
Stereo Audio signals are produced through two channels. A spectacular sound is reproduced
with two separated speakers.
Widescreen Term given to picture displays with a wider aspect ratio than NTSC 4:3. Digital HDTV is
16:9 widescreen. Most motion pictures also have a widescreen aspect ratio, some
even wider than 16:9.
Panorama screen Refers to a screen whose distortion due to the screen size has been calibrated.
External source Refers source signals that come from other external devices such as a VCR, camcorder
and DVD player, etc. than a TV set.
MTS A bilingual service provided when an overseas film, foreign drama or overseas news,
etc. is aired. You can select one of two choices: mother tongue and foreign language.
Or you can listen to both languages at the same time.
DVI Digital Visual Interface is a specification for digital signals. This interface using TMDS
transmission reduces the loss of signal, allowing to enjoy a clear and crisp image.
HDMI HDMI (High-Definition Multimedia Interface) is the first and only industry-supported,
uncompressed, all-digital audio/video interface.
HDMI provides an interface between any audio/video source, such as a set-top box,
DVD player, or A/V receiver and an audio and/or video monitor, such as a digital
television (DTV), over a single cable.
Virtual channels For terrestrial reception of digital signals, virtual channels are used. A virtual channel
allows users to use channel digits, regardless of their area, allocated to each
broadcasting station.
To receive digital signals, you have to automatically tune channels or in case of off-air,
you have to directly select UHF channel digits aired by individual stations or in case of
cable broadcasting, you have to directly select channel digits allocated by local cable
stations. For example, the UHF 14 (MBC), 15 (KBS1), 16 (SBS), 17 (KBS2), and 18 (EBS)
transmitted from Kwanak Mountain are indicated with virtual channels, 11-1 (MBC), 9-
1 (KBS1), 6- 1 (SBS), 7-1 (KBS2), and 10-1 (EBS), which will be used by you. These
virtual channels are all used in the same way nationwide but the channel digits may be
different depending on local stations. Since the digital channels may be allocated
differently according to areas or changed by the broadcasting policy, contact your local
broadcasting stations and cable companies for more details.
Once virtual channels have been memorized, you can watch virtual channels by
pressing channel numbers.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Installation Problems
Symptom
Possible solution
How can I install an
antenna?
Refer to pages 19~20.
TV screen is not clear after
installing an indoors
antenna.
Indoors antenna may experience poor reception due to surrounding buildings. Please
install an outdoors antenna or wireless antenna.
How can I view cable
broadcasting?
Please install a cable broadcasting receiver (Converter).
Picture Problems
Symptom
Possible solution
Neither picture nor
sound comes up.
Check whether power is on.
Check whether the power is cut or whether power cord is properly connected.
Try to plug another product’s power cord to the outlet the PDP is plugged into.
Picture turns on slowly
after power is on.
This symptom is not a malfunction. This delay is designed to prevent the distorted and
noisy picture when power is on. However, if the picture does not appear more than 5
minutes after power is on, call a service center.
Picture is distorted or frozen
while watching digital
broadcasting.
This symptom may be caused by weak reception. Contact your local station or cable
company.
Input Source information
only appears on black
screen.
Check whether your TV is properly connected to external devices.
Poor reception on some
channels.
Check whether you selected proper channels. Try re-orienting your antenna. Ensure
LNA is activated.
Black and white on some
channels.
Check other channels for black and white screen. Adjust colour.
TV won’t turn on.
Ensure the power cord is plugged.
Adjust brightness.
Screen is too bright or too
dark.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Auto On does not work.
Ensure to use the remote control or power button on the product to turn off your TV. If
you unplug the power cord, the stand-by consumption power becomes 0 (zero), which
causes the programmed time to be erased.
After setting the time,
I turned TV off and turn it on.
The programmed information
has been erased.
Ensure to use the remote control or power button on the product to turn off your TV. If
you unplug the power cord, the stand-by consumption power becomes 0 (zero), which
causes the programmed time to be erased.
Sound Problems
Symptom
Possible solution
Too much noise occurs.
Check whether the audio setting is in the Stereo mode. In the Stereo mode, the sound
may be distorted in the area where experiences poor reception or is located far away
from a TV broadcasting station.
No sound while viewing a
cable channel
Make sure an audio or audio/video component is securely inserted into the appropriate
jacks. Check other channels for sound. Check the volume settings on the cable
broadcasting receiver.
Picture is OK but sound does
not come out.
Try to press volume up/volume down buttons of your remote control.
One of the speakers does not
produce sound.
Select sound balance and make proper adjustment. (Page 39)
Check the speaker connection cables.
General
Symptom
Possible solution
Remote control won't work.
Check whether there is a blocking object between the remote control and PDP.
Make sure your PDP is Power On. (In case of normal, LED on the front panel is in Red.)
Check whether batteries are inserted with proper polarities(+, -).
When the batteries are worn out, replace with new ones.
Where does the S-Video
cable plug in for audio
output?
Connect the two Audio jacks from the S-Video cable to the left and right ports on the
Composite.
Strange noises are heard.
Ticking noise during or after watching is caused by the change of ambient
environment such as humidity and temperature, which is characterized by plastic
products. Strange ticking noise occurs because a signal is suddenly transmitted to the
PDP panel. So, this is not a malfunction.
I tried to use the TV screen
as a PC monitor
Adjust the resolution referring to the standard signal mode table. Check the
specification of your video card installed in your PC. If your video card does not work in
supported hardware. Try upgrading the video card’s driver.
but it doesn’t work.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Cabinet Cleaning
Wipe a soft dry cloth.
Do not use inflammables like Benzene or Thinner, or wet clothes.
Do not scratch the panel of PDP with a fingernail or pointed object.
Screen Cleaning
Clean the screen with a soft cloth moistened in mild glass
detergent and dry with a soft cloth.
Never use any solvent on the screen such as Acetone, Benzene, or
Thinner, etc.
Cleaning Inside
When the inside needs to be cleaned, contact a service center or
distribution agent where the item is purchased.
It is recommended cleaning is complete before the rainy season.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
HYUNDAI Digital LCD TV
Product Specifications
Q261
Q320/Q321
Q400/Q401
Model
1EA (A/V audio common)
1EA (A/V audio common)
1EA (Audio included)
2EA (Audio included)
2EA (ANT1+ANT2)
D-SUB
1EA (A/V audio common)
1EA (Audio included)
2EA (Audio included)
2EA (ANT1+ANT2)
D-SUB
Input
S-Video
1EA (Audio included)
Video (RCA)
2EA (Audio included)
Component(Y/Cb/Cr)
Antenna
2EA (ANT1+ANT2)
D-SUB
PC Connection jack
Max. resolution
Audio
1024 X 768 @ 85 Hz
1024 X 768 @ 85 Hz
L/R
1024 X 768 @ 85 Hz
L/R
L/R
1EA
1EA
1EA
HDMI-HDCP(or DVI-HDCP)
Memory Slot
Subwoofer
No
Slot 1, Slot 2, USB(Only Q320) Slot 1, Slot 2, USB(Only Q400)
1EA
1EA
1EA
Output
1EA (Audio included)
1EA (Audio included)
1EA (Audio included)
Video
NTSC M
FM
NTSC M
FM
NTSC M
FM
TV/Video
Color system
Sound system
Video system
Component, S-Video,
Component, S-Video,
Component, S-Video,
Composite, PC, HDMI(or DVI) Composite, PC, HDMI(or DVI)
Composite, PC, HDMI(or DVI)
AC 100 - 240 V, 50/60 Hz
Typical 120W
Typical 2W
AC 100 - 240 V, 50/60 Hz
Typical 150W
Typical 2W
AC 100 - 240 V, 50/60 Hz
Typical 245W
Power
Supply
Consumption power
Stand-by power
Typical 2W
640 x 230 x 485
17.5 Kg
772 x 230 x 563
19.3 Kg
988 x 297 x 715.5
23.0 Kg
Dimension (W x D x H mm - Stand included)
Weigh (Stand included)
Control type
Remote control, Key control Remote control, Key control
Remote control, Key control
- The above specifications may be subject to change without prior notice.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
|