Hotpoint Washer Dryer AQGMD 129 User Manual

Instruction booklet  
WASHER-DRYER  
Contents  
GB  
Installation, 2-3-4-5  
Unpacking and levelling  
GB  
Connecting the cold water and electricity supplies  
Technical data  
English, 1  
Description of the machine, 6-7  
Control panel  
Running a wash cycle,8  
Programmes and options, 9-10  
Table of Programmes  
Wash options  
Drying  
Detergents and laundry, 11  
Detergent  
AQUALTIS  
Preparing the laundry  
Washing advice  
Load-balancing system  
AQGMD 129  
Precautions and tips, 12  
General safety  
Disposal  
Opening the door manually  
Care and maintenance, 13  
Turning off the water and electricity supplies  
Cleaning the machine  
Cleaning the detergent dispenser  
Drum maintenance  
Cleaning the pump  
Checking the water inlet hose  
Troubleshooting, 14  
Assistance, 15  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Drainage Connection  
the supply voltage is included within the values i  
ndicated on the Technical details table  
(on the page 5);  
GB  
Connect the drain hose,  
without kinking it, to a  
draining duct or a stand  
pipe situated between  
65 and 100 cm from the  
floor;  
the socket is compatible with the washing  
machine's plug. If this is not the case, replace  
the socket or the plug.  
65 - 100 cm  
Your appliance is now supplied with a 13 amp fused  
plug it can be plugged into a 13 amp socket for  
immediate use. Before using the appliance please  
read the instructions below.  
The drain hose may be  
connected to an under-  
sink trap. Before  
WARNING - THIS APPLIANCE MUST BE EARTHED.  
THE FOLLOWING OPERATIONS SHOULD BE CARRIED  
OUT BY A QUALIFIED ELECTRICIAN.  
connecting the drain  
hose from the machine  
ensure that any blanks  
or removable ends have  
been taken off the  
spigot.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA  
approved fuse to BS 1362 should always be used,  
and the fuse cover re-fitted. If the fuse cover is  
lost, the plug must not be used until a replacement  
is obtained.  
Replacement fuse covers:  
If it is placed over the  
edge of a basin or sink  
be sure the free end of  
the hose should not be  
underwater.  
If a replacement fuse cover is fitted, it must be of  
the correct colour as indicated by the coloured  
marking or the colour that is embossed in words on  
the base of the plug. Replacements can be obtained  
directly from your nearest Service Depot.  
Removing the plug:  
If your appliance has a non-rewireable moulded plug  
and you should wish to re-route the mains cable  
through partitions, units etc., please ensure that  
either:  
! We advise against the use of hose extensions; in  
case of absolute need, the extension must have  
the same diameter as the original hose and must  
not exceed 150 cm in length.  
the plug is replaced by a fused 13 ampere re-  
wearable plug bearing the BSI mark of approval.  
or:  
the mains cable is wired directly into a 13 amp cable  
outlet, controlled by a switch, (in compliance with  
BS 5733) which is accessible without moving the  
appliance.  
Ensure that if the drain hose is pushed into a  
standpipe, that the end does not go down more  
than 15cms (6 inches). If the hose is pushed down  
too far, this may cause the machine to self -  
syphon ie. continuously empty as it is filling.  
Disposing of the plug:  
Ensure that before disposing of the plug itself, you  
make the pins unusable so that it cannot be  
accidentally inserted into a socket.  
Electric connection  
Before plugging the appliance into the mains  
socket, make sure that:  
Instructions for connecting cable to an alternative  
plug:  
the socket is earthed and in compliance with  
the applicable law;  
Important: the wires in the mains lead are coloured  
in accordance with the following code:  
Green & Yellow Earth  
the socket is able to sustain the appliance's  
maximum power load indicated in the Technical  
details table (on the page 5);  
B l u e  
B r o w n  
Neutral  
L i v e  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
As the colours of the wires in the lead may not  
correspond with the coloured markings identifyng  
the terminals in your plug, proceed as follows:  
Connect Green & Yellow wire to terminal marked E  
GB  
or  
or coloured Green or Green & Yellow.  
Connect Brown wire to terminal marked L or  
coloured Red.  
Connect Blue wire to terminal marked N or coloured  
Black.  
If a 13 amp plug (BS 1363) is used it must be fitted  
with a 13 amp fuse, either in the plug or adaptor or  
at the distribution board.  
If you are in any doubt the electrical supply to your  
machine, consult a qualified electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in  
accordance with the following code:  
BLUE  
BROWN  
GREEN & YELLOW  
NEUTRAL (N)  
LIVE (L)  
EARTH (E)  
Disposing of the appliance:  
When disposing of the appliance please remove the  
plug by cutting the mains cable as close as possible  
to the plug body and dispose of it as described  
above.  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
CROSS-BAR  
CORD GRIP  
BLUE  
! The washing machine should not be installed in an  
outdoor environment, not even when the area is  
sheltered, because it may be very dangerous to  
leave it exposed to rain and thunderstorms.  
! When the washing machine is installed, the mains  
socket must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent or  
dangerously compressed.  
! The power supply cable must only be replaced by  
an authorised serviceman.  
Warning! The company denies all liability if and when  
these norms are not respected.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
GB  
Technical data  
Model  
AQGMD 129  
width 59.5 cm  
height 85 cm  
depth 64.5 cm  
Dimensions  
Capacity  
from 1to 8 kg for wash programme  
from 1 to 6 kg for the drying programme  
Electrical  
connections  
please refer to the technical data plate  
fixed to the machine  
maximum pressure 1 MPa (10 bar)  
minimum pressure 0.05 MPa (0.5 bar)  
drum capacity 62 litres  
Water  
connections  
Spin speed  
up to 1200 rotations per minute  
Wash: COTTON WHITES programme;  
temperature 60°C;  
Energy rated  
programmes  
according to  
regulation  
using a load of 8 kg.  
Drying: first drying cycle performed  
with a 2 kg load, by selecting the drying  
level "IRON";  
EN 50229  
Second drying cycle performed with a  
6 kg load, selecting the maximum drying  
level "CUPBOARD".  
This appliance conforms to the following  
EC Directives:  
- 89/336/EEC dated 03/05/89  
(Electromagnetic Compatibility) and  
subsequent modifications  
- 2002/96/EC  
- 2006/95/EC (Low Voltage)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Description of the machine  
C O NTRO L  
PA N E L  
GB  
DOOR  
DOOR  
HANDLE  
TOE-KICK  
ADJUSTABLE FEET  
DOOR  
DETERGENT  
DISPENSER  
This is inside the  
Always use the handle  
to open the door (see  
figure).  
machine and may be  
accessed by opening the  
door.  
For information relating  
to detergents, please  
refer to the chapter  
entitled “Detergents  
and laundry.  
1. pre-wash  
compartment: use  
powder detergent.  
2. main wash  
1
2
compartment: use  
powder or liquid  
detergent. If you intend  
to use liquid detergent,  
we recommend that it is  
poured into the  
compartment immediately before the wash cycle is  
started.  
compartment for additives: for fabric softener  
or other liquid washing additives. Do not exceed the  
maximum level indicated by the grille, and dilute  
concentrated fabric softeners.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control panel  
TEMPERATURE  
button  
WAS H  
C Y C L E  
PHASE  
icons  
GB  
PROGRAMME  
knob and MEMO  
buttons  
START/PAUSE  
button with indicator  
light  
SPIN SPEED  
button  
CHILD LOCK  
button and indicator  
light  
E C O  
indicator  
light  
O N - O F F/ CA N C E L  
button with indicator light  
OPTION  
buttons  
INFO  
button  
D O O R  
L O C K  
indicator light  
DELAY TIMER  
button  
DISPLAY  
ON-OFF/CANCEL button with indicator light  
press the button briefly to switch the machine on  
or off. The green indicator light shows that the  
:
WASH CYCLE PHASE icons: these light up to  
provide an indication of the progress of the wash  
cycle (Wash  
The text  
- Rinse  
- Spin  
- Drying ).  
lights up when the cycle has finished.  
machine is switched on. To switch the washer-dryer  
off during a wash cycle, press and hold the button  
for approximately 2 seconds; pressing the button  
quickly or accidentally will not switch the machine  
off.  
START/PAUSE button with indicator light: when  
the green indicator light flashes slowly, press the  
button to start the wash cycle. When the cycle has  
started, the indicator light is illuminated in a fixed  
manner. To pause the wash cycle, press the button  
again; the indicator light will turn orange and begin  
If the machine is switched off during a wash cycle,  
the programme will be cancelled.  
PROGRAMME knob: this can be rotated in both  
directions. To set a more suitable programme,  
please refer to the “Table of Programmes”.  
The knob is locked into position during the wash  
cycle.  
to flash again. If the “Door Locked”  
indicator  
light is off, the porthole door may be opened. To  
restart the wash cycle from the point at which it  
was interrupted, press the button again.  
DOOR LOCKED indicator light: this indicates  
that the porthole door is locked. To open the door,  
pause the wash cycle (see following page).  
MEMO buttons: press and hold one of the buttons  
to store a cycle with your own set preferences in  
the memory of the machine. To recall a previously-  
stored cycle, press the corresponding button.  
CHILD LOCK  
button and indicator light: this is  
used to enable or disable the “Child lock” function, by  
pressing the button for approximately 2 seconds. When  
the indicator light is illuminated, the control panel is  
locked. This avoids accidental changes being made to  
the wash cycles, especially where children are at home.  
TEMPERATURE button: press to decrease the  
temperature: the value will be shown on the display.  
SPIN CYCLE button: press to reduce the r.p.m.  
value or to exclude the spin cycle completely: the  
value will be shown on the display.  
ECO indicator light: the  
icon lights up when the  
electricity saving reaches at least 10% (this can be  
achieved by adjusting the wash cycle settings).  
DELAYED START  
button: press to set a  
delayed start time for the selected programme.  
The delay time will be shown on the display.  
! When the machine is first switched on, you will be asked to  
choose a language (Select Language appears on the display):  
press the INFO button repeatedly until the required language  
appears on the display. After 5 seconds the language  
selection will be stored in the memory of the machine. If the  
wrong language is selected by mistake, press and hold the  
INFO and DELAYED START buttons simultaneously; this will  
return the language selection menu to the display.  
OPTION buttons: the name of the option will be shown  
on the display when the corresponding button is  
pressed. When the relevant indicator light illuminates,  
this shows that the option has been selected.  
INFO button: press the button to display information  
relating to the selected wash cycle and options.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Running a wash cycle  
NOTE: the first time you use the washer-dryer,  
add detergent and run an empty 90°C cotton wash  
cycle without the pre-wash phase.  
Modifying the cycle settings.  
GB  
Press the button to activate the option; the name  
of the option will then appear on the display and  
the corresponding indicator light will illuminate.  
Press the button again to deactivate the  
option; the name of the option will then appear  
on the display followed by the text OFF, and the  
corresponding indicator light will switch off.  
1. SWITCH THE MACHINE ON. Press the  
button. All the indicator lights will illuminate for 1  
second and the text OK will appear on the display;  
the indicator light corresponding to the  
button will then remain lit in a constant manner  
and the START/PAUSE indicator light will flash.  
! If the selected option is not compatible with the  
set programme, the indicator light will flash and  
the option will not be activated.  
2. LOAD THE LAUNDRY. Open the porthole door.  
Load the laundry, making sure you do not exceed  
the maximum load value indicated by the display  
and in the programme table on the following page.  
! If the selected option is not compatible with  
another option that has been selected previously,  
the indicator light corresponding to the first option  
selected will flash and only the second option will be  
activated; the indicator light corresponding to the  
active option will remain lit in a constant manner.  
3. MEASURE OUT THE DETERGENT. Pull out the  
detergent dispenser drawer and pour the  
detergent into the relevant compartments as  
described in "Description of the machine".  
For advice as to the type of detergent to use for  
! The options may affect the recommended load  
value and/or the duration of the cycle.  
each cycle, press the  
button.  
7. START THE PROGRAMME. Press the START/  
PAUSE button. The corresponding indicator light  
remains lit in a fixed manner and the porthole  
door locks (the DOOR LOCKED indicator light  
illuminates). During the wash cycle, the display  
will show which stage is currently in progress and  
the icon corresponding to each stage will illumi-  
nate. To change a programme while a cycle is in  
progress, pause the washer-dryer by pressing  
the START/PAUSE button; then select the desired  
cycle and press the START/PAUSE button again.  
To open the door while a cycle is in progress  
press the START/PAUSE button; if the DOOR  
4. CLOSE THE PORTHOLE DOOR.  
5. SELECT THE PROGRAMME. Turn the  
PROGRAMME KNOB left or right, until the  
required programme has been selected; the  
name of the programme will appear on the  
display. A temperature and spin speed is set for  
each programme; these may be adjusted. The  
recommended drum load level and the cycle  
duration will also appear on the display.  
6. PERSONALISE THE WASH CYCLE. Use the  
relevant buttons on the control panel:  
LOCK  
indicator light switches off it is  
Modify the temperature and/or the spin  
speed. The machine automatically selects the  
temperature and the maximum spin speed for the  
programme set and these values may not be  
possible to open the door. Press the START/  
PAUSE button again to resatrt the programme  
from the point at which it was interrupted.  
increased. By pressing the  
rature can be progressively reduced or even set  
to cold wash “OFF”. By pressing the button, the  
spin speed can be progressively reduced or even  
eliminated altogether “OFF”. If the buttons are  
pressed again the maximum values are restored.  
button, the tempe-  
8. PROGRAMME END. The text END lights up to  
indicate that the programme has ended. The  
porthole door may be opened immediately. If the  
START/PAUSE button flashes, press the button  
to end the cycle. open the door, unload the  
laundry and switch off the machine.  
! Exception: if the COTTON WHITES programme is  
selected, the temperature can be increased up  
to a value of 90°C.  
! If you wish to cancel a cycle that has already  
begun, press and hold the button. The cycle will  
be stopped and the machine will switch off.  
Setting a delayed start.  
To set a delayed start for the selected  
programme, press the corresponding button  
repeatedly until the required delay period has  
been reached. When this option has been  
activated, the  
symbol appears on the display.  
To remove the delayed start option, press the  
button until the display shows the text OFF; the  
symbol will disappear.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programmes and options  
Table of Programmes  
GB  
Max.  
Max.  
tempera-  
ture (°C)  
Detergent  
spin  
speed  
(r.p.m.)  
Maximum Cycle  
load (kg) duration  
Icon Programme description  
Drying  
Fabric  
softener  
Washing  
Everyday programmes  
60°  
(Max 90°)  
COTTON WHITES  
1200  
8
l
l
l
COTTON WHITES: Heavily soiled whites and delicate colours.  
COTTON COLOURFAST  
40°  
40°  
40°  
1200  
1200  
800  
8
8
4
l
l
l
l
l
l
l
l
l
SYNTHETICS DELICATE  
FASTWASH: Refreshes lightly soiled garments quickly (not  
recommended for wool, silk or clothes that should be  
washed by hand).  
30°  
800  
3.5  
l
l
l
Vigorous programmes  
COTTON PREWASH: Removes stubborn stains.  
(Add detergent to the relevant compartment).  
90°  
60°  
1200  
800  
8
4
l
l
l
l
l
l
SYNTHETICS NON-DELICATES  
Special programmes  
SHIRTS  
40°  
30°  
40°  
60°  
600  
0
2
2
2
8
l
-
l
l
l
l
l
l
l
l
SILK: Washes silk and garments and lingerie.  
WOOL: Washes wool, cashmere, etc.  
BED&BATH: Washes bathroom laundry and bedlinen.  
Drying programmes  
800  
1200  
l
l
Drying cycle for cottons  
Drying cycle for synthetics  
Drying cycle for wool  
-
-
-
-
-
-
-
-
-
-
-
-
6
4
l
l
l
1,5  
Partial programmes  
Rinse cottons  
-
-
-
1200  
1200  
0
-
-
-
8
8
8
l
l
-
l
-
Fast Spin cottons  
Pump out  
-
The information contained in the table is purely indicative.  
Extra Rinse  
Wash options  
This programme increases the efficiency of the  
rinse phase and ensures that a greater amount of  
detergent is removed. It is particularly  
recommended for skin types that are sensitive to  
detergents. We recommend this programme is used  
when the washer-dryer is full or when a large  
amount of detergent has been used.  
Super Wash  
This option guarantees a high-performance wash,  
thanks to the use of a greater quantity of water  
during the initial phase of the cycle and a longer  
overall duration of the programme.  
! It is not compatible with the Fastwash, Silk, Wool,  
“Partial programmes” and “Drying programmes.  
! This option is not compatible with the Fastwash,  
Fast Spin cottons, Pump out and “Drying  
programmes”.  
Reduce creases  
If this option is selected, the wash and spin phases will be  
adjusted accordingly so that fabric creasing is reduced.  
At the end of the cycle the drum of the washer-dryer will  
spin slowly; the “Reduce creases” and START/PAUSE  
indicator lights will flash. To end the cycle, press the  
START/PAUSE button or the “Reduce creases” button.  
When using the Silk programme, the machine will end  
the cycle while the laundry is soaking and the “Reduce  
creases” and START/PAUSE indicator lights will flash.  
To drain the water so that the laundry can be removed,  
press the START/PAUSE button or the “Reduce  
creases” button.  
! This option is not compatible with the Fastwash,  
Wool, Fast Spin cottons, Pump out and “Drying  
programmes”.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Drying  
GB  
Table of drying times (guideline values)  
Fabric type  
Cotton  
Load type  
Max. load (kg)  
Cupbprad  
180  
Hanger  
170  
Iron  
160  
160  
145  
Clothing of different sizes, Terry towels  
Sheets, Shirts, Pyjamas, socks, etc.  
Knitwear, Pullovers, etc.  
6
4
Synthetics  
Wool  
180  
170  
1,5  
165  
155  
Set the drying cycle  
Press the button to set the desired drying type. Two options are available:  
A - Based on the damp level of the dry clothes:  
Iron: slightly damp clothes, easy to iron.  
Hanger: ry clothes to put away.  
Cupboard: very dry clothes, recommended for towelling and bathrobes.  
B - Based on time: 40’ - 90’ - 180’ (max. 5 kg).  
To remove the drying cycle, press the button until the display shows the text OFF.  
If your laundry load to wash and dry is exceptionally in excess of the maximum load foreseen (see table of  
drying times), perform the wash cycle, and when the programme is complete, divide up the garments and put  
part of them back in the drum. Now follow the instructions provided for a “Dry only” cycle. Repeat this proce-  
dure for the remainder of the load.  
N.B.: a cooling-down period is always added to the end of each drying cycle.  
Dry only  
Turn the PROGRAMME knob to one of the drying settings (  
select the desired drying type using the DRYING button  
-
-
) depending on the type of fabric, then  
.
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Detergents and laundry  
Detergent  
Curtains: these should be folded and placed inside  
the bag provided. Use the "Silk" programme.  
GB  
The type and quantity of detergent used depends on  
the type of fabric (cotton, wool, silk...), its colour, the  
temperature of the wash, the level of soiling and the  
hardness of the water in the area.  
Wool: Hotpoint is the only washer-dryer to have  
obtained the prestigious Woolmark Platinum Care  
mark of recognition (M.0508) from The Woolmark  
Company, which certifies the machine washing of all  
woollen garments, even those whose label states  
Measuring out the detergent carefully will avoid  
accidental spills and help to protect the environment:  
although they may be biodegradable, detergents  
contain elements that alter the balance of nature.  
“hand wash only”  
. The “Wool” programme  
therefore offers you complete peace of mind when  
washing all woollen garments, with great perfor-  
mance guaranteed every time.  
We recommend:  
Bathroom laundry and bedlinen: this washer-  
dryer can be used to wash any domestic laundry in a  
single cycle called “BED&BATH” that optimises the  
use of fabric softener while saving both time and  
electricity. We recommend that you use a powder  
detergent.  
the use of powder detergents for white cotton  
garments and for pre-wash phases;  
the use of liquid detergents for delicate cotton  
garments and for all programmes which run at a  
low temperature;  
the use of liquid detergents for wool and silk.  
Stubborn stains: stubborn stains should be  
treated with solid soap before the garment is  
washed (use the Cotton programme with pre-wash  
phase).  
! Do not use detergents when washing garments by  
hand, because they create too much foam.  
The detergent must be measured out into the  
relevant compartment, or into the detergent  
dosing ball which will be placed directly into the  
drum of the machine. In this case the Cotton cycle  
with pre-wash phase may not be selected.  
Load-balancing system  
Before every spin cycle, to avoid excessive  
vibrations and to distribute the load in a uniform  
manner, the drum rotates continuously at a speed  
which is slightly faster than the normal washing  
speed. If, after several attempts, the load is still  
not evenly distributed, the machine spins at a lower  
speed than the set frequency.  
Preparing the laundry  
! Unfold all items of laundry before placing them in  
the machine.  
Divide the laundry according to type of material  
(the symbol on the garment label) and colour,  
making sure that whites are separated from  
coloured garments.  
If the load is excessively unbalanced, the washer-  
dryer continues at distribution speed only instead  
of the full spin speed.  
In order to achieve better load distribution and  
balance, we recommend that large and small  
garments are mixed when placing the laundry in the  
machine.  
Empty all pockets and check for loose buttons.  
Do not exceed the values indicated in the “Table  
of Programmes”, which refer to the weight of the  
laundry items when they are dry.  
How much does your laundry weigh?  
1 sheet  
400 - 500 g  
150 - 200 g  
400 - 500 g  
900 - 1200 g  
150 - 250 g  
400 - 500 g  
150 - 200 g  
1 pillowcase  
1 tablecloth  
1 bathrobe  
1 towel  
1 pair of jeans  
1 shirt  
Washing advice  
Shirts: use a suitable programme to wash shirts  
made from different fabrics and in different  
colours. This will guarantee that these garments  
are looked after properly.  
Silk: use the relevant programme designed for all  
silk garments. We recommend the use of a special  
detergent for delicate garments.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions and tips  
! This machine was designed and manufactured in  
compliance with cuurent international safety  
standards. The following advice is provided for  
safety reasons and should be read carefully.  
remind the owner of their obligations regarding  
separated waste collection.  
GB  
For more information relating to the correct  
disposal of household appliances, owners should  
contact their local authorities or appliance dealer.  
General safety  
Opening the door manually  
This appliance was designed for domestic use inside  
the home and is not intended for commercial or  
industrial use.  
If it is not possible to open the porthole door due to  
a powercut and you wish to hang out the laundry,  
proceed as follows:  
The washer-dryer must be used by adults only, in  
accordance with the instructions provided in this  
booklet.  
1. Remove the plug from the  
electricity socket;  
Do not touch the machine when barefoot or with wet  
or damp hands or feet.  
2. Make sure that the water  
level inside the machine is  
lower than the door opening;  
When unplugging the appliance, always pull the plug  
from the mains socket; do not pull on the cable.  
Do not touch the drained water as it may reach  
extremely high temperatures.  
if this is not the case  
remove excess water using  
the water outlet hose,  
collecting it in a bucket as  
shown in the figure;  
Never force the porthole door: doing so may damage  
the safety lock mechanism designed to prevent the  
door being opened accidentally.  
If the appliance breaks down, under no circumatances  
must you attempt to carry out the repairs yourself.  
Keep children well away from the machine while it is in  
operation.  
3. Remove the covering  
panel on the front of the  
washer-dryer using a  
screwdriver (see figure);  
If the machine must be moved, work in a group of two  
or three people and handle it very carefully. Never  
attempt to move the appliance without the help of  
another person, because it is extremely heavy.  
Make sure that the drum is empty before loading  
laundry into the appliance.  
During the drying phase, the door tends to get  
quite hot.  
4. Using the tab shown in  
the figure, pull outwards  
until the plastic brace  
comes away; pull it  
Do not use the appliance to dry clothes that have  
been washed with flammable solvents (e.g.  
trichlorethylene).  
downwards until you  
hear a “click”, which  
indicates that the door  
is unlocked;  
Do not use the appliance to dry foam rubber or  
similar elastomers.  
Make sure that the water tap is turned on during  
the drying cycles.  
Disposal  
5. Open the door; if this  
is still not possible,  
repeat the process;  
When disposing of the packaging material: observe  
local legislation so that the packaging may be reused.  
The European Directive 2002/96/EC relating to  
Waste Electrical and Electronic Equipment  
states that household appliances should not be  
disposed of using the normal solid urban waste  
cycle. Exhausted appliances should be collected  
separately in order to optimise the cost of re-  
using and recycling the materials inside the  
machine, while preventing potential damage to  
the atmosphere and to public health. The  
6. Replace the kick strip, making sure that the  
hooks are positioned in the right slots before  
pushing the panel towards the machine.  
crossed-out dustbin is marked on all products to  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and maintenance  
To access the pre-chamber:  
Turning off the water and electricity  
supplies  
GB  
1. Remove the kick strip  
on the front of the  
machine using a  
Turn off the water tap after every wash. This  
limits wear and tear on the machine’s water  
supply and prevents leaks.  
screwdriver (see figure);  
Disconnect the appliance from the electricity  
supply before cleaning it and before performing  
any maintenance work on it.  
Cleaning the machine  
2. Position a container  
collecting the drained  
water (approximately 1.5  
l) correctly (see figure);  
3. Unscrew the cover,  
turning it in an  
The exterior of the appliance and all rubber parts  
may be cleaned using a cloth soaked in warm soapy  
water. Do not use solvents or abrasive products.  
anticlockwise direction  
(see figure);  
Cleaning the detergent dispenser  
drawer  
To remove the drawer,  
press the lever (1) and  
pull it outwards (2) (see  
figure).  
4. Clean the inside thoroughly;  
5. Screw the cover back on;  
Wash the drawer under  
running water; this  
should be done regularly.  
6. Replace the kick strip, making sure that the  
hooks are positioned in the right slots before  
pushing the panel towards the machine.  
Checking the water inlet hose  
Drum maintenance  
Check the water inlet hose at least once a year. If  
there are any cracks, replace it immediately: the  
high water pressure used by the wash cycles could  
cause a cracked hose to split open.  
Always leave the porthole door ajar to prevent  
unpleasant odours from forming.  
Cleaning the pump  
The washer-dryer is fitted with a self-cleaning  
pump which does not require regular maintenance.  
However, it may be that small objects (coins,  
buttons, etc.) fall into the pre-chamber that  
protects the pump (the pump is located in the lower  
part of this pre-chamber).  
! Make sure that the wash cycle has finished and  
remove the plug from the socket.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
From time to time your machine may not operate as it should. Before calling for Assistance (see “Assistance”),  
make sure that the problem cannot be resolved easily using the following list.  
GB  
Malfunction:  
Possible causes / Solutions:  
The plug has not been inserted into the electrical socket, or it has not  
been inserted far enough to make contact.  
There is no power in the house.  
The washer-dryer  
will not switch on.  
The porthole door has not been shut properly.  
The START/PAUSE button has not been pressed.  
The water tap has not been turned on.  
The wash cycle  
does not begin.  
The water inlet hose is not connected to the tap.  
The hose is kinked.  
The water tap has not been turned on.  
There is no water in the house.  
The washer-dryer fails to fill  
with water.  
The water pressure is insufficient.  
The START/PAUSE button has not been pressed.  
The machine continuously fills  
and drains water.  
The end of the outlet hose has not been fitted at a height between 65  
and 100 cm from the floor (see “Installation”).  
The free end of the hose is underwater (see “Installation”).  
If If the dwelling is on one of the upper floors of a building, there may  
be problems relating to water drainage, causing the washer-dryer to  
load and drain water continuously. Special anti-draining valves are  
available in shops and help to avoid this inconvenience.  
The water drainage systemis not fitted with a breather pipe.  
The washer-dryer does not  
drain or spin.  
The programme does not include a draining phase: some programmes  
require manual draining (see “Programmes and options”).  
The “Easy Iron” option is enabled: to complete the programme, press  
the START/PAUSE button (see “Programmes and options”).  
The outlet hose is bent (see “Installation”).  
The drainage duct is clogged.  
The drum was not unlocked properly when the appliance was installed (see “Installation”).  
The washer-dryer is not level (see “Installation”).  
The washer-dryer is trapped between cabinets and a wall (see “Installation”).  
The load is not balanced properly (see “Description of the machine”).  
The washer-dryer vibrates  
too much during the spin cycle.  
The water inlet hose is not screwed on to the tap correctly (see “Installation”).  
The detergent dispenser drawer is blocked (for instructions on how to  
clean it, see “Care and maintenance”).  
The washer-dryer leaks.  
The outlet hose has not been secured properly (see “Installation”).  
Switch off the machine and unplug the appliance; wait for  
approximately 1 minute then switch it on again.  
If the problem persists, contact Assistance.  
The icons corresponding to  
the “Phase in progress” flash  
rapidly at the same time as  
the ON/OFF indicator light.  
The detergent is not designed for machine washing (the packaging should state that  
the product is “for washing by machine”, “for washing by hand or machine” or similar).  
Too much detergent was used.  
There is too much foam.  
Follow the manual unlocking procedure (see “Precautions and tips”).  
The washer-dryer door remains locked.  
The washer-dryer does not dry.  
The appliance is not plugged into the socket, or not enough to make contact.  
There has been a power failure.  
The appliance door is not shut properly.  
A delayed start has been set.  
The DRYING cycle is on the OFF setting.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assistance  
Guarantee  
12 Months Parts and Labour Guarantee  
GB  
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of  
breakdown repairs for twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective  
because of either workmanship or materials, we will, at our discretion, either repair or replace the  
appliance at no cost to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our  
operating and maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise  
interfered with by any person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
Damage resulting from transportation, improper use, neglect or interference or as a result  
of improper installation.  
-
-
Replacement of any consumable item or accessory . These include but are not limited to: plugs,  
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL  
OR NON-DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on  
you registering your appliance with us and the parts being fitted by one of our authorised engineers.  
There will be a charge for our engineer's time. To activate the extra parts warranty on your  
appliance, simply call our registration line on 0870 6092094 (ROI 01 230 0800).  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense  
of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on  
08709 088 088 (ROI 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint  
Service Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where  
necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will  
replace your machine or, if you prefer, give you your money back.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
195067280.01  
01/2008  
-
Xerox Business Services  
After Sales Service  
No one is better placed to care for your Hotpoint appliance during the course of its  
working life than us - the manufacturer.  
GB  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and  
1100 fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08709 066 066  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and  
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08709 077 077  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts  
guarantee you must register your appliance with us.  
UK: 0870 6092094  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17  
Recycling & Disposal Information  
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right  
to use quality, recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,  
remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts  
separately to ensure that the appliance can no longer be plugged into a mains socket, and the door  
cannot be locked shut.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Heat Pump 332291C User Manual
Grindmaster Coffeemaker 77110 User Manual
Grizzly Musical Instrument H3098 User Manual
Haier Video Games Y 716 User Manual
Healthrider Treadmill HRTL10982 User Manual
HP Hewlett Packard Laptop 2000 5700 User Manual
HP Hewlett Packard Network Card YELLOWJACKET PLUS User Manual
Hunter Fan Humidifier 38200 User Manual
Husqvarna Blower 356BFX User Manual
IBM Laptop MT 2675 User Manual