Model:
HTS93G
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
EN
The minimum distance between the supporting surface
for the cooking vessels on the hob and the lowest part
of the range hood must be not less than 50cm from
electric cookers and 65cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify
a greater distance, this must be adhered to.
! It is important to conserve this booklet for
consultation at any moment. In the case of sale,
cession or move, make sure it is together with the
product.
! Read the instructions carefully: there is important
information about installation, use and safety.
Expansion wall plugs are provided to secure the hood
to most types of walls/ceilings. However, a qualified
technician must verify suitability of the materials in
accordance with the type of wall/ceiling. The
wall/ceiling must be strong enough to take the weight
of the hood. Do not tile, grout or silicone this appliance
to the wall. Surface mounting only.
! Do not carry out electrical or mechanical variations
on the product or on the discharge conduits.
! Your hood is ready to be used in the suction version.
To use the filtering version, you must order the suitable
kit where you will find all the necessary details.
The information for transforming the hood from the
suction version to the filtering version is already
contained in the manual supplied with the product.
Installation
Electrical connection
The mains power supply must correspond to the rating
indicated on the plate situated inside the hood. If
provided with a plug connect the hood to a socket in
compliance with current regulations and positioned in
an accessible area. If it not fitted with a plug (direct
mains connection) or if the plug is not located in an
accessible area apply a bi-polar switch in accordance
with standards which assures the complete
disconnection of the mains under conditions relating to
over-current category III, in accordance with
installation instructions.
Warning! Before re-connecting the hood circuit to the
mains supply and checking the efficient function,
always check that the mains cable is correctly
assembled.
Connection to a discharge tube
Connect the hood and discharge holes on the walls
with a diameter equivalent to the air outlet (connection
flange).
Using the tubes and discharge holes on walls with
smaller dimensions will cause a diminution of the
suction performance and a drastic increase in noise.
Any responsibility in the matter is therefore declined.
! The company declines any responsibility whenever
these regulations are not respected.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Preliminary information for installing the hood:
Disconnect the power supply at the domestic main
switch before carrying out electrical connections.
Remove the grease filter/s.
EN
1. Using a pencil, draw the centre line on the wall up
to the ceiling to facilitate installation operations.
2. Apply the drilling template to the wall: Align the
vertical centre-line on the drilling template with the
centre-line drawn on the wall. The template’s
bottom edge represents the bottom edge of the
hood.
3. Place the lower support bracket on the hole
diagram so that it matches the dotted rectangle,
mark the two external holes and drill.
Note: Drill all the holes indicated on the template:
the top 2 holes are for hanging the hood and the
bottom holes (generally 1 central or 2 side holes)
are for fixing it securely to the wall.
Remove the hole diagram, insert the wall plugs and
fix the hood support bracket with two 5 x 45 mm
screws.
4. Fit the flue support bracket “G” to the wall and
against the ceiling, use the support bracket as a
hole diagram (if present, the small slot on the
support must match the line drawn on the wall ),
mark 2 holes with the pencil then drill the holes (Ø 8
mm) and finally insert 2 plugs.
5. Fix the flue support bracket to the wall with two 5 x
45 mm screws.
6. Hook the hood to the lower bracket.
7. Adjust the distance between the hood and the wall.
8. Adjust the hood horizontally.
9. Fix the hood securely to the wall (ABSOLUTELY
NECESSARY!!).
10.Connect an exhaust pipe (pipe and clamps are not
supplied and must be bought separately) to the
collar located above the extraction motor unit.
For extractor operation, connect the other end of
the exhaust pipe to the home discharge device. For
filter operation, fix the deflector F to the flue support
bracket G and connect the other end of the exhaust
pipe to the deflector collar F.
11.Insert the steam deflector and secure it to the
supports (11b) on the extractor unit with 2 bushings
and 2 screws (11a).
12.Make all necessary electrical connections.
13.Fit the flues over the extractor unit, engaging them
in their seat above the hood.
14.Slide the top section of the flue and secure it with 2
screws (14a) to the flue support bracket “G” (14b).
Refit the grease filter/s and check for correct hood
operation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the appliance
EN
Control panel
Calibrating the control panel
or one of the following keys:
.
,
or
When the plug is inserted (or after a blackout) the
system calibrates the keys; during calibration all the
luminous display parts flash. Calibration lasts 15”. All
the display parts stop flashing at the end of calibration.
Fats filter signal: this symbol (red led) lights up
Off/Stand by: the On condition is obtained by
after 40 hours. Reset the signal by pressing
for a
long time (at least 3 seconds) until the beep confirms
it.
pressing
and
for 3 seconds; in this case keys
Carbon filter signal action.
This signal is shown only if it has been previously set.
are enabled, the display point and the blue led
of the relative keys light up. The Off condition is
Proceed as follows: press
with the hood in Off:
also
obtained by pressing
again for 3 seconds.
first
turns red, after about 1 second
turns red. If you want to eliminate the carbon filter
On/Off lights: press
to switch on the lights,
which turn amber. Contemporaneously the symbols at
the sides and turn blue: the intensity of
signal previously set, press
Reset the carbon filter signal (after 160 hours) by
with the hood in Off.
the light can be increased and diminished with these.
pressing
for a long time (about 3 seconds, until
the beep).
Once the luminosity has been set, pressing
rapidly again memorises it (the symbol turns blue) and
the light
switches off.
On/Off motor: press
to switch the motor on.
It turns amber. Contemporaneously the symbols at the
sides
Press
and
or
as well as
turn blue.
to adjust the intensity of
suction. Pressing
again switches the motor off
and the last speed set is memorised.
Intensive timing: by pressing this key the suction
of the hood becomes intensive for a maximum time of 5
minutes. At the end the hood returns to the speed
previously set. To exit from the function earlier press
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
! We advise switching the hood on, at minimum power,
before beginning to cook to favour the optimal
EN
expulsion of odours. In addition we advise turning it off
every time 10/15 minutes after finishing cooking.
! We advise frying under the hood only under constant
supervision.
! It is forbidden to cook flambé under the hood
because there is the risk of causing a fire.
The best performance of the apparatus is obtained
with external expulsion: we advise using the hood in
this version if possible.
External exhausting version
In this case the fumes are conveyed outside by means
of a special pipe connected with the connection ring
located on top of the hood.
Attention! The exhausting pipe is not supplied and
must be purchased apart.
Diameter of the exhausting pipe must be equal to that
of the connection ring = 150mm.
In the horizontal runs the exhausting pipe must be
slightly slanted (about 10°) and directed upwards to
vent the air easily from the room to the outside.
Attention! If the hood is supplied with active charcoal
filter, then it must be removed.
Filtering version
One active charcoal filter is needed for this and can be
obtained from your usual retailer.
The filter removes the grease and smells from the
extracted air before sending it back into the room
through the upper outlet grid.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
EN
! It is always necessary to isolate the hood from the
power supply during cleaning and maintenance.
Therefore remove the plug.
We recommend carrying our maintenance regularly
(about every 10 days) to ensure efficacious and
constant performance of the hood.
Cleaning the grease filters
Traps cooking grease particles.
This must be cleaned once a month (or when the filter
saturation indication system – if envisaged on the
model in possession – indicates this necessity) using
non aggressive detergents, either by hand or in the
dishwasher, which must be set to a low temperature
and a short cycle.
When washed in a dishwasher, the grease filter may
discolour slightly, but this does not affect its filtering
capacity.
Cleaning
The cooker hood should be cleaned regularly (at least
with the same frequency with which you carry out
maintenance of the fat filters) internally and externally.
Clean using the cloth dampened with neutral liquid
detergent. Do not use abrasive products. DO NOT USE
ALCOHOL!
Remove the filter holder frame by turning the knobs (g)
90° that affix the chimney to the cooker hood.
WARNING: Failure to carry out the basic cleaning
recommendations of the cooker hood and replacement
of the filters may cause fire risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any
damage to the motor or any fire damage linked to
inappropriate maintenance or failure to observe the
above safety recommendations.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Cleaning the carbon filter
Replacing lamps
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two
months (or when the filter saturation indication system
– if envisaged on the model in possession – indicates
Disconnect the hood from the electricity.
Warning! Prior to touching the light bulbs ensure they
are cooled down.
1. Using a flat head screwdriver or equivalent tool,
this necessity)
detergent, or in
using hot water and a suitable
dishwasher at 65°C (if the
carefully pry loose the light cover.
2. Remove the damaged light and replace with a new
12 Volt, 20 Watt (Maximum) halogen light made for
a
dishwasher is used, select the full cycle function and
leave dishes out).
a
G-4 base SUITABLE FOR USE IN OPEN
Eliminate excess water without damaging the filter,
then put it in the oven for 10 minutes at 100° C to dry
completely. Replace the mattress every 3 years and
when the cloth is damaged.
LUMINAIRES. Follow package directions and do
not touch new light with bare hands.
3. Reinstall the light cover. (it will snap shut).
Mounting and changing the filter
Assembly
Place the mat around the grease filter and fix it in place
using the devices provided.
Position the upper cap and fix it in place using the
fixing pin.
To disassemble, perform the steps in the reverse
order.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
EN
General safety
Disposal
!
Do not connect the appliance to the mains until the
installation is fully complete.
• Disposing of the packaging material: keep to the
local regulations so that the packaging can be re-used.
! In case of anomalies apply to the authorized technical
assistance service and require original spare parts.
! The information and technical data are subject to
change and the producer, in line with technical
progress, maintains the right to make modifications
that he considers necessary without prior notice.
!
Before any cleaning or maintenance operation,
disconnect the hood from the mains by removing
the plug or disconnecting the home mains switch.
The appliance is not intended for use by children or
persons with impaired physical, sensorial or mental
faculties, or if lacking in experience or know-how,
unless they are under supervision or have been
trained in the use of the appliance by a person
responsible for their safety.
!
This appliance is marked according to the European
directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE). By ensuring this product
is disposed of correctly, you will help prevent potential
negative consequences for the environment and
human health, which could otherwise be caused by
inappropriate waste handling of this product.
!
!
!
!
Children should be monitored to ensure that they
do not play with the appliance.
Never use the hood without effectively mounted
grating.!
The hood must NEVER be used as a support
surface unless specifically indicated.
The premises must be sufficiently ventilated, when
the kitchen hood is used together with other gas
combustion devices or other fuels.
The symbol
on the product, or on the documents
accompanying the product, indicates that this
appliance may not be treated as household waste.
Instead it shall be handed over to the applicable
collection point for the recycling of electrical and
electronic equipment. Disposal must be carried out in
accordance with local environmental regulations for
waste disposal.
For more detailed information about treatment,
recovery and recycling of this product, please contact
your local city office, your household waste disposal
service or the shop where you purchased the product.
!
The suctioned air must not be conveyed into a
conduit used for the disposal of the fumes
generated by appliances that combust gases or
other fuels.
!
!
The flaming of foods beneath the hood itself is
severely prohibited.
The use of exposed flames is detrimental to the
filters and may cause a fire risk, and must therefore
be avoided in all circumstances.
!
!
Any frying must be done with care in order to make
sure that the oil does not overheat and burst into
flames.
As regards the technical and safety measures to be
adopted for fume discharging it is important to
closely follow the relations provided by the
competent authorities.
!
The hood must be regularly cleaned on both the
inside and outside (AT LEAST ONCE A MONTH, it
is in any event necessary to proceed in accordance
with the maintenance instructions provided in this
manual)..
!
!
Failure to follow the instructions as concerns hood
and filter cleaning will lead to the risk of fires.
Do not use or leave the hood without the lamp
correctly mounted because of the possible risk of
electric shocks.
!
We decline any responsibility for any problems,
damage or fires caused to the appliance as the
result of the non-observance of the instructions
included in this manual.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|