Husqvarna Chainsaw 223L User Manual
Operator’s manual (EPA)  
223L  
Please read the operator’s manual carefully and make sure you  
understand the instructions before using the machine.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
Contents  
Note the following before starting:  
KEY TO SYMBOLS  
Please read the operator’s manual carefully.  
Symbols .......................................................................  
CONTENTS  
2
Long-term exposure to noise can result in permanent hearing  
impairment. So always use approved hearing protection.  
Contents ......................................................................  
Note the following before starting: ................................  
INTRODUCTION  
3
3
Maintenance, replacement, or repair of the emission control  
devices and system may be performed by any nonroad  
engine repair establishment or individual.  
Dear customer! ............................................................  
WHAT IS WHAT?  
4
5
WARNING! Under no circumstances may the  
design of the machine be modified without  
the permission of the manufacturer. Always  
use genuine accessories. Non-authorized  
modifications and/or accessories can result  
in serious personal injury or the death of the  
operator or others.  
What is what? ..............................................................  
GENERAL SAFETY PRECAUTIONS  
Important ......................................................................  
Personal protective equipment .....................................  
Machine′s safety equipment ........................................  
Cutting equipment ........................................................  
ASSEMBLY  
!
6
6
7
9
Your warranty may not cover damage or  
liability caused by the use of non-authorized  
accessories or replacement parts.  
Fitting the loop handle ................................................. 10  
Fitting the trimmer head ............................................... 10  
Fitting the trimmer guard and trimmer head ................ 10  
FUEL HANDLING  
WARNING! A clearing saw, brushcutter or  
trimmer can be dangerous if used  
incorrectly or carelessly, and can cause  
serious or fatal injury to the operator or  
others. It is extremely important that you  
read and understand the contents of this  
operator’s manual.  
Fuel safety ................................................................... 11  
Fuel .............................................................................. 11  
Fueling ......................................................................... 12  
STARTING AND STOPPING  
!
Check before starting ................................................... 13  
Starting and stopping ................................................... 13  
WORKING TECHNIQUES  
General working instructions ....................................... 15  
MAINTENANCE  
Carburetor .................................................................... 17  
Muffler .......................................................................... 18  
Cooling system ............................................................ 18  
Spark plug .................................................................... 19  
Air filter ......................................................................... 19  
Maintenance schedule ................................................. 20  
TECHNICAL DATA  
This label certify that the product has been certified in  
accordance with American exhaust requirements EPA 2.  
Technical data .............................................................. 21  
FEDERAL EMISSION CONTROL WARRANTY  
STATEMENT  
YOUR WARRANTY RIGHTS AND OBLIGATIONS ..... 22  
The Emissions Compliance Period referred to on the  
Emission Compliance label indicates the number of operating  
hours for which the engine has been shown to meet Federal  
emissions requirements. Category C = 50 hours, B = 125  
hours, and A = 300 hours.  
English – 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
INTRODUCTION  
Dear customer!  
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the  
Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The  
location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During over  
300 years of continuous operation, the Husqvarna factory has produced a lot of different products, from wood stoves to modern  
kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first motor driven lawn mowers appeared, followed  
by chain saws in 1959, and it is within this area Husqvarna is working today.  
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our highest priority.  
We develop, manufacture and market high quality motor driven products for forestry and gardening as well as for building and  
construction industry.  
Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the retailer who  
sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.  
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator′s  
manual as a valuable document.By following its′ content (using, service, maintenance etc) the life span and the second-hand value  
of the machine can be extended. If you ever lend or sell this machine, make sure that the borrower or buyer gets the operator′s  
manual, so they will also know how to properly maintain and use it.  
Thank you for using a Husqvarna product.  
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and  
appearance of products without prior notice.  
For customer assistance call: 704-921-7000 or contact us at our website: www.husqvarna.com  
4 – English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
WHAT IS WHAT?  
What is what?  
1
2
3
4
5
6
7
8
9
Trimmer head  
Grease filler cap, bevel gear  
Bevel gear  
12 Fuel tank  
13 Choke control  
14 Air purge  
Cutting attachment guard  
Shaft  
15 Air filter cover  
16 Handle adjustment  
17 Drive disc  
Loop handle  
Throttle control  
Stop switch  
18 Operator’s manual  
19 Allen key  
Throttle lock  
20 Locking pin  
10 Cylinder cover  
11 Starter handle  
21 Spark plug cap and spark plug  
English – 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GENERAL SAFETY PRECAUTIONS  
Important  
Personal protective equipment  
IMPORTANT!  
IMPORTANT!  
The machine is only designed for trimming grass.  
A clearing saw, brushcutter or trimmer can be dangerous if  
used incorrectly or carelessly, and can cause serious or  
fatal injury to the operator or others. It is extremely  
important that you read and understand the contents of this  
operator’s manual.  
The only accessories you can operate with this engine unit  
are the cutting attachments we recommend in the chapter  
on Technical data.  
Never use the machine if you are tired, if you have drunk  
alcohol, or if you are taking medication that could affect your  
vision, your judgement or your co-ordination.  
You must use approved personal protective equipment  
whenever you use the machine. Personal protective  
equipment cannot eliminate the risk of injury but it will  
reduce the degree of injury if an accident does happen. Ask  
your dealer for help in choosing the right equipment.  
Wear personal protective equipment. See instructions  
under the heading Personal protective equipment.  
Never use a machine that has been modified in any way  
from its original specification.  
WARNING! Listen out for warning signals or  
shouts when you are wearing hearing  
protection. Always remove your hearing  
protection as soon as the engine stops.  
Never use a machine that is faulty. Carry out the checks,  
maintenance and service instructions described in this  
manual.Some maintenance and service measures must be  
carried out by trained and qualified specialists. See  
instructions under the heading Maintenance.  
!
HEARING PROTECTION  
Wear hearing protection that provides adequate noise  
reduction.  
All covers and guards must be fitted before starting. Ensure  
that the spark plug cap and ignition lead are undamaged to  
avoid the risk of electric shock.  
The machine operator must ensure that no people or  
animals come closer than 15 metres while working. When  
several operators are working in the same area the safety  
distance should be at least twice the tree height and no less  
than 15 metres.  
EYE PROTECTION  
Always wear approved eye protection. If you use a visor then  
you must also wear approved protective goggles. Approved  
protective goggles must comply with standard ANSI Z87.1 in  
the USA or EN 166 in EU countries.  
WARNING! Running an engine in a confined  
or badly ventilated area can result in death  
due to asphyxiation or carbon monoxide  
poisoning.  
!
WARNING! Never allow children to use or be  
in the vicinity of the machine. As the  
machine is equipped with a spring-loaded  
!
GLOVES  
stop switch and can be started by low speed  
and force on the starter handle, even small  
children under some circumstances can  
produce the force necessary to start the  
machine.This can mean a risk of serious  
personal injury.Therefore remove the spark  
plug cap when the machine is not under  
close supervision.  
Gloves should be worn when necessary, e.g., when fitting  
cutting attachments.  
BOOTS  
Wear sturdy, non-slip boots.  
CLOTHING  
Wear clothes made of a strong fabric and avoid loose clothing  
that can catch on twigs and branches. Always wear heavy,  
long pants. Do not wear jewellery, shorts sandals or go  
barefoot. Secure hair so it is above shoulder level.  
6 – English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
GENERAL SAFETY PRECAUTIONS  
FIRST AID KIT  
Make sure the throttle control is locked at the idle setting  
when the throttle lock is released.  
Always have a first aid kit nearby.  
Press the throttle lock and make sure it returns to its original  
position when you release it.  
Machine′s safety equipment  
This section describes the machine′s safety equipment, its  
purpose, and how checks and maintenance should be carried  
out to ensure that it operates correctly. See the ”What is  
what?” section to locate where this equipment is positioned  
on your machine.  
The life span of the machine can be reduced and the risk of  
accidents can increase if machine maintenance is not carried  
out correctly and if service and/or repairs are not carried out  
professionally. If you need further information please contact  
your nearest servicing dealer.  
Check that the throttle control and throttle lock move freely  
and that the return springs work properly.  
IMPORTANT!  
All servicing and repair work on the machine requires  
special training. This is especially true of the machine′s  
safety equipment. If your machine fails any of the checks  
described below you must contact your service agent.  
When you buy any of our products we guarantee the  
availability of professional repairs and service. If the retailer  
who sells your machine is not a servicing dealer, ask him for  
the address of your nearest service agent.  
See instructions under the heading Start. Start the machine  
and apply full throttle. Release the throttle and check that the  
cutting attachment stops and remains at a standstill. If the  
cutting attachment rotates with the throttle in the idle position  
then the carburettor idle setting must be checked. See  
instructions under the heading Maintenance.  
WARNING! Never use a machine with faulty  
safety equipment.The machine’s safety  
equipment must be checked and maintained  
as described in this section. If your machine  
fails any of these checks contact your  
service agent to get it repaired.  
!
Throttle lock  
Stop switch  
The throttle lock is designed to prevent accidental operation  
of the throttle control. When you press the lock (A) (i.e. when  
you grasp the handle) it releases the throttle control (B).  
When you release the handle the throttle control and the  
throttle lock both move back to their original positions. This  
movement is controlled by two independent return springs.  
This arrangement means that the throttle control is  
automatically locked at the idle setting.  
Use the stop switch to switch off the engine.  
Start the engine and make sure the engine stops when you  
move the stop switch to the stop setting.  
English – 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
GENERAL SAFETY PRECAUTIONS  
Regularly check the vibration damping units for cracks or  
deformation. Check that the vibration damping element is  
undamaged and securely attached.  
Cutting attachment guard  
WARNING! Overexposure to vibration can  
lead to circulatory damage or nerve damage  
in people who have impaired circulation.  
Contact your doctor if you experience  
symptoms of overexposure to vibration.  
These symptoms include numbness, loss of  
feeling, tingling, pricking, pain, loss of  
strength, changes in skin colour or  
condition.These symptoms normally appear  
in the fingers, hands or wrists.  
This guard is intended to prevent loose objects from being  
thrown towards the operator. The guard also protects the  
operator from accidental contact with the cutting attachment.  
!
Check that the guard is undamaged and not cracked.Replace  
the guard if it has been exposed to impact or is cracked.  
Muffler  
Always use the recommended guard for the cutting  
attachment you are using. See chapter on Technical data.  
The muffler is designed to keep noise levels to a minimum  
and to direct exhaust fumes away from the user.  
WARNING! Never use a cutting attachment  
without an approved guard. See the chapter  
on Technical data. If an incorrect or faulty  
guard is fitted this can cause serious  
personal injury.  
!
A muffler fitted with a catalytic converter is also designed to  
reduce harmful exhaust gases.  
Vibration damping system  
In countries that have a warm and dry climate there is a  
significant risk of fire. We therefore fit certain mufflers with a  
spark arrestor mesh. Check whether the muffler on your  
machine is fitted with this kind of mesh.  
Your machine is equipped with a vibration damping system  
that is designed to reduce vibration and make operation  
easier.  
Use of incorrectly wound cord or an incorrect cutting  
attachment increases the level of vibration. See instructions  
under the heading Cutting equipment.  
For mufflers it is very important that you follow the instructions  
on checking, maintaining and servicing your machine.  
The machine′s vibration damping system reduces the transfer  
of vibration between the engine unit/cutting equipment and  
the machine′s handle unit.  
Never use a machine that has a faulty muffler.  
Regularly check that the muffler is securely attached to the  
machine.  
8 – English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GENERAL SAFETY PRECAUTIONS  
If the muffler on your machine is fitted with a spark arrestor  
Cutting equipment  
mesh this must be cleaned regularly. A blocked mesh will  
cause the engine to overheat and may lead to serious  
damage.  
This section describes how to choose and maintain your  
cutting equipment in order to:  
•
•
•
Reduce the risk of blade thrust.  
Obtain maximum cutting performance.  
Extend the life of cutting equipment.  
IMPORTANT!  
Only use cutting attachments with the guards we  
recommend! See the chapter on Technical data.  
WARNING! Mufflers fitted with catalytic  
converters get very hot during use and  
!
remain so for some time after stopping.This  
Refer to the instructions for the cutting attachment to check  
the correct way to load the cord and the correct cord  
diameter.  
also applies at idle speed. Contact can result  
in burns to the skin. Remember the risk of  
fire!  
WARNING! Always stop the engine before  
WARNING! The inside of the muffler contain  
chemicals that may be carcinogenic. Avoid  
contact with these elements in the event of a  
damaged muffler.  
doing any work on the cutting attachment.  
This continues to rotate even after the  
throttle has been released. Ensure that the  
cutting attachment has stopped completely  
and disconnect the HT lead from the spark  
plug before you start to work on it.  
!
!
WARNING! Bear in mind that:  
!
!
The exhaust fumes from the engine are hot  
and may contain sparks which can start a  
fire. Never start the machine indoors or near  
combustible material!  
WARNING! A faulty cutting attachment may  
increase the risk of accidents.  
!
Trimmer head  
Locking nut  
IMPORTANT!  
Always ensure the trimmer cord is wound tightly and evenly  
around the drum, otherwise the machine will generate  
harmful vibration.  
A locking nut is used to secure some types of cutting  
attachment.  
•
Only use the recommended trimmer heads and trimmer  
cords.These have been tested by the manufacturer to suit  
a particular engine size.This is especially important when  
a fully automatic trimmer head is used. Only use the  
recommended cutting attachment. See the chapter on  
Technical data.  
When fitting, tighten the nut in the opposite direction to the  
direction of rotation of the cutting attachment. To remove it,  
undo the nut in the same direction as the cutting attachment  
rotates. (CAUTION! The nut has a left-hand thread.)  
•
•
Smaller machines generally require small trimmer heads  
and vice versa. This is because when clearing using a  
cord the engine must throw out the cord radially from the  
trimmer head and overcome the resistance of the grass  
being cleared.  
•
Tighten the nut using the socket spanner. 35-50 Nm (3.5-  
5 kpm).  
The nylon lining inside the locking nut must not be so worn  
that you can turn it by hand. The lining should offer a  
resistance of at least 1.5 Nm. The nut should be replaced  
after it has been put on approx. 10 times.  
The length of the cord is also important. A longer cord  
requires greater engine power than a shorter cord of the  
same diameter.  
•
•
Make sure that the cutter on the trimmer guard is intact.  
This is used to cut the cord to the correct length.  
To increase the life of the cord it can be soaked in water  
for a couple of days.This will make the line tougher so that  
it lasts longer.  
English – 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ASSEMBLY  
Fitting the loop handle  
Fitting the trimmer guard and  
trimmer head  
•
Position the handle on the shaft. Note that the handle  
must be mounted below the arrow on the shaft.  
•
Fit the correct trimmer guard (A) for use with the trimmer  
head.  
Hook the trimmer guard/combination guard onto the fitting  
on the shaft and secure with the bolt (L).  
•
•
Fit the screw, securing plate and wing nut as shown in the  
diagram.  
•
•
Fit the drive disc (B) on the output shaft.  
Tighten the wing nut.  
Turn the blade shaft until one of the holes in the drive disc  
aligns with the corresponding hole in the gear housing.  
Fitting the trimmer head  
•
•
Insert the locking pin (C) in the hole to lock the shaft.  
Screw on the trimmer head/plastic blades (H) in the  
opposite direction to the direction of rotation.  
When fitting the cutting attachment it is extremely important  
that the raised section on the drive disc/support flange  
engages correctly in the centre hole of the cutting attachment.  
If the cutting attachment is fitted incorrectly it can result in  
serious and/or fatal personal injury.  
H
H
•
To dismantle, follow the instructions in the reverse order.  
WARNING! Never use a cutting attachment  
without an approved guard. See the chapter  
on Technical data. If an incorrect or faulty  
guard is fitted this can cause serious  
personal injury.  
!
10 – English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
FUEL HANDLING  
Gasoline  
Fuel safety  
Never start the machine:  
1
2
If you have spilt fuel on it. Wipe off the spillage and allow  
remaining fuel to evaporate.  
CAUTION! Always use a quality gasoline/oil mixture with an  
octane rating of at least 87 octane ((RON+MON)/2). If your  
machine is equipped with a catalytic converter (see chapter  
on Technical data) always use a good quality unleaded  
gasoline/oil mixture.Leaded gasoline will destroy the catalytic  
converter.  
If you have spilt fuel on yourself or your clothes, change  
your clothes.Wash any part of your body that has come in  
contact with fuel. Use soap and water.  
3
If the machine is leaking fuel. Check regularly for leaks  
from the fuel cap and fuel lines.  
Use low-emission gasoline, also known as alkylate gasoline,  
if it is available.  
Transport and storage  
•
Store and transport the machine and fuel so that there is  
no risk of any leakage or fumes coming into contact with  
sparks or naked flames, for example, from electrical  
machinery, electric motors, electrical relays/switches or  
boilers.  
•
•
When storing and transporting fuel always use approved  
containers intended for this purpose.  
This engine is certified to operate on unleaded gasoline.  
•
The lowest recommended octane grade is 87  
When storing the machine for long periods the fuel tank  
must be emptied.Contact your local gas station to find out  
where to dispose of excess fuel.  
((RON+MON)/2). If you run the engine on a lower octane  
grade than 87 so-called knocking can occur. This gives  
rise to a high engine temperature and increased bearing  
load, which can result in serious engine damage.  
•
•
Ensure the machine is cleaned and that a complete  
service is carried out before long-term storage.  
•
When working at continuous high revs a higher octane  
rating is recommended.  
The transport guard must always be fitted to the cutting  
attachment when the machine is being transported or in  
storage.  
Two-stroke oil  
•
In order to prevent unintentional starting of the engine, the  
spark plug cap must always be removed during long-term  
storage, if the machine is not under close supervision and  
when performing all service measures.  
•
For best results and performance use HUSQVARNA two-  
stroke engine oil, which is specially formulated for our air-  
cooled two stroke-engines.  
•
Never use two-stroke oil intended for water-cooled  
engines, sometimes referred to as outboard oil (rated  
TCW).  
WARNING! Take care when handling fuel.  
Bear in mind the risk of fire, explosion and  
inhaling fumes.  
•
•
Never use oil intended for four-stroke engines.  
Mixing ratio  
!
Fuel  
1:50 (2%) with HUSQVARNA two-stroke oil.  
CAUTION! The machine is equipped with a two-stroke  
engine and must always been run using a mixture of gasoline  
and two-stroke engine oil. It is important to accurately  
measure the amount of oil to be mixed to ensure that the  
correct mixture is obtained. When mixing small amounts of  
fuel, even small inaccuracies can drastically affect the ratio of  
the mixture.  
Two-stroke oil, litre  
Gasoline, litre  
2% (1:50)  
5
0,10  
10  
0,20  
15  
0,30  
20  
0,40  
WARNING! Fuel and fuel fumes are highly  
inflammable and can cause serious injury  
when inhaled or allowed to come in contact  
with the skin. For this reason observe  
caution when handling fuel and make sure  
there is adequate ventilation.  
US gallon  
US fl. oz.  
2 1/2  
6 1/2  
12 7/8  
!
1
2 1/2  
5
English – 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
FUEL HANDLING  
Mixing  
Fueling  
•
Always mix the gasoline and oil in a clean container  
intended for fuel.  
•
Always start by filling half the amount of the gasoline to be  
used. Then add the entire amount of oil. Mix (shake) the  
fuel mixture. Add the remaining amount of gasoline.  
WARNING!Taking the following precautions,  
will lessen the risk of fire:  
•
Mix (shake) the fuel mixture thoroughly before filling the  
machine’s fuel tank.  
!
Do not smoke or place hot objects near fuel.  
Always shut off the engine before refuelling.  
Always stop the engine and let it cool for a  
few minutes before refuelling.  
When refuelling, open the fuel cap slowly so  
that any excess pressure is released gently.  
Tighten the fuel cap carefully after refuelling.  
Always move the machine away from the  
refuelling area before starting.  
•
•
Do not mix more than one month’s supply of fuel at a time.  
•
•
Clean the area around the fuel cap. Contamination in the  
tank can cause operating problems.  
If the machine is not used for some time the fuel tank  
should be emptied and cleaned.  
Ensure that the fuel is well mixed by shaking the container  
before filling the tank.  
WARNING! The catalytic converter muffler  
gets very hot during and after use.This also  
applies during idling. Be aware of the fire  
hazard, especially when working near  
flammable substances and/or vapours.  
!
12 – English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
STARTING AND STOPPING  
Check before starting  
Starting and stopping  
WARNING! When the engine is started with  
WARNING! The complete clutch cover and  
the choke in either the choke or start throttle  
positions the cutting attachment will start to  
rotate immediately.  
shaft must be fitted before the machine is  
started, otherwise the clutch can come loose  
and cause personal injury.  
!
!
Always move the machine away from the  
refuelling area before starting. Place the  
machine on a flat surface. Ensure the cutting  
attachment cannot come into contact with  
any object.  
•
•
Never start the machine indoors. Exhaust fumes can be  
dangerous if inhaled.  
Observe your surroundings and make sure that there is no  
risk of people or animals coming into contact with the  
cutting equipment.  
Make sure no unauthorised persons are in  
the working area, otherwise there is a risk of  
serious personal injury.The safety distance  
is 15 metres.  
•
Place the machine on the ground, ensure the cutting  
attachment is clear of twigs and stones. Hold the body of  
the machine on the ground using your left hand  
(CAUTION! Not with your foot). Then grip the starter  
handle with your right hand and pull the starter cord.  
Starting  
Primer bulb: Press the air purge repeatedly until fuel begins  
to fill the bulb. The bulb need not be completely filled.  
For safety reasons follow these recommendations!  
•
Check that the support flange is not cracked due to fatigue  
or due to being tightened too much. Discard the support  
flange if it is cracked.  
Choke: Set the choke control in the choke position.  
•
Ensure the locking nut has not lost its captive force. The  
nut lock should have a locking force of at least 1.5 Nm.  
The tightening torque of the locking nut should be 35-50  
Nm.  
Hold the body of the machine on the ground using your left  
hand (CAUTION! Not with your foot!). Grip the starter handle,  
slowly pull out the cord with your right hand until you feel  
some resistance (the starter pawls grip), now quickly and  
powerfully pull the cord.Never wrap the starter cord around  
your hand  
•
Check that the trimmer head and trimmer guard are not  
damaged or cracked. Replace the trimmer head or  
trimmer guard if they have been exposed to impact or are  
cracked.  
•
Never use the machine without a guard nor with a  
defective guard.  
English – 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
STARTING AND STOPPING  
Repeat pulling the cord until the engine starts. When the  
engine starts. return choke control to run position and apply  
full throttle; the throttle will automatically disengage from the  
start setting.  
CAUTION! Do not pull the starter cord all the way out and do  
not let go of the starter handle when the cord is fully extended.  
This can damage the machine.  
CAUTION!  
Do not put any part of your body in marked area. Contact can  
result in burns to the skin, or electrical shock if the spark plug  
cap has been damaged. Always use gloves. Do not use a  
machine with damaged spark plug cap.  
Stopping  
The engine is switched off by moving the stop switch to the  
stop position.  
CAUTION! The stop switch automatically returns to the start  
position. In order to prevent unintentional starting, the spark  
plug cap must be removed from the spark plug when  
assembling, checking and/or performing maintenance.  
14 – English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WORKING TECHNIQUES  
6
Always hold the machine with both hands. Hold the  
machine on the right side of your body.  
General working instructions  
IMPORTANT!  
This section takes up the basic safety precautions for  
working with a trimmer.  
If you encounter a situation where you are uncertain how to  
proceed you should ask an expert. Contact your dealer or  
your service workshop.  
Avoid all usage which you consider to be beyond your  
capability.  
You must understand the difference between forestry  
clearing, grass clearing and grass trimming before use.  
7
8
Keep the cutting attachment below waist level.  
Switch off the engine before moving to another area. Fit  
the transport guard before carrying or transporting the  
equipment any distance.  
Basic safety rules  
9
Never put the machine down with the engine running  
unless you have it in clear sight.  
1
•
Look around you:  
WARNING! Neither the operator of the  
machine nor anyone else may attempt to  
remove the cut material while the engine is  
running or the cutting equipment is rotating,  
as this can result in serious injury.  
To ensure that people, animals or other things cannot  
affect your control of the machine.  
!
•
To ensure that people, animals, etc., do not come into  
contact with the cutting attachment or loose objects that  
are thrown out by the cutting attachment.  
Stop the engine and cutting equipment  
before you remove material that has wound  
around the blade shaft as otherwise there is  
a risk of injury.The bevel gear can get hot  
during use and may remain so for a while  
afterwards.You could get burnt if you touch  
it.  
•
CAUTION! Do not use the machine unless you are able to  
call for help in the event of an accident.  
2
Inspect the working area. Remove all loose objects, such  
as stones, broken glass, nails, steel wire, string, etc. that  
could be thrown out or become wrapped around the  
cutting attachment.  
3
4
Do not use the machine in bad weather, such as dense  
fog, heavy rain, strong wind, intense cold, etc. Working in  
bad weather is tiring and often brings added risks, such as  
icy ground, unpredictable felling direction, etc.  
WARNING! Watch out for thrown objects.  
Always wear approved eye protection. Never  
lean over the cutting attachment guard.  
Stones, rubbish, etc. can be thrown up into  
the eyes causing blindness or serious injury.  
!
Make sure you can move and stand safely.Check the area  
around you for possible obstacles (roots, rocks, branches,  
ditches, etc.) in case you have to move suddenly. Take  
great care when working on sloping ground.  
Keep unauthorised persons at a distance.  
Children, animals, onlookers and helpers  
should be kept outside the safety zone of 15  
m. Stop the machine immediately if anyone  
approaches. Never swing the machine  
around without first checking behind you to  
make sure no-one is within the safety zone.  
Basic working techniques  
Always slow the engine to idle speed after each working  
operation. Long periods at full throttle without any load on the  
engine can lead to serious engine damage.  
5
Keep a good balance and a firm foothold.  
WARNING! Sometimes branches or grass  
get caught between the guard and cutting  
attachment. Always stop the engine before  
cleaning.  
!
English – 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
WORKING TECHNIQUES  
Sweeping  
Grass trimming with a trimmer head  
•
The fan effect of the rotating cord can be used for quick  
and easy clearing up. Hold the cord parallel to and above  
the area to be swept and move the tool to and fro.  
Trimming  
•
Hold the trimmer head just above the ground at an angle.  
It is the end of the cord that does the work. Let the cord  
work at its own pace. Never press the cord into the area  
to be cut.  
•
When cutting and sweeping you should use full throttle to  
obtain the best results.  
•
•
The cord can easily remove grass and weeds up against  
walls, fences, trees and borders, however it can also  
damage sensitive bark on trees and bushes, and damage  
fence posts.  
Reduce the risk of damaging plants by shortening the  
cord to 10-12 cm and reducing the engine speed.  
Clearing  
•
The clearing technique removes all unwanted vegetation.  
Keep the trimmer head just above the ground and tilt it.Let  
the end of the cord strike the ground around trees, posts,  
statues and the like. CAUTION! This technique increases  
the wear on the cord.  
•
•
The cord wears quicker and must be fed forward more  
often when working against stones, brick, concrete, metal  
fences, etc., than when coming into contact with trees and  
wooden fences.  
When trimming and clearing you should use less than full  
throttle so that the cord lasts longer and to reduce the  
wear on the trimmer head.  
Cutting  
•
The trimmer is ideal for cutting grass that is difficult to  
reach using a normal lawn mower. Keep the cord parallel  
to the ground when cutting. Avoid pressing the trimmer  
head against the ground as this can ruin the lawn and  
damage the tool.  
•
Do not allow the trimmer head to constantly come into  
contact with the ground during normal cutting. Constant  
contact of this type can cause damage and wear to the  
trimmer head.  
16 – English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
Carburetor  
Your Husqvarna product has been designed and  
WARNING! If the idle speed cannot be  
adjusted so that the cutting attachment  
stops, contact your dealer/service  
workshop. Do not use the machine until it  
has been correctly adjusted or repaired.  
!
manufactured to specifications that reduce harmful  
emissions. After the engine has used 8-10 tanks of fuel the  
engine will be run-in.To ensure that it continues to run at peak  
performance and to minimise harmful exhaust emissions  
after the running-in period, ask your dealer/service workshop  
(who will have a rev counter at their disposal) to adjust your  
carburettor.  
Fine adjustment  
•
When the machine has been ”run-in” the carburetor  
should be finely adjusted. The fine adjustment should  
be carried out by a qualified person. First adjust the L-  
jet, then the idling screw T and then the H-jet.  
WARNING! The complete clutch cover and  
shaft must be fitted before the machine is  
started, otherwise the clutch can come loose  
and cause personal injury.  
!
Conditions  
•
Before any adjustments are made, make sure that the air  
filter is clean and the air filter cover is fitted. If you adjust  
the carburettor when the air filter is dirty it will result in a  
leaner mixture when the filter is finally cleaned. This can  
lead to serious engine damage.  
Function  
•
•
•
Carefully turn both jets, L and H, so that they are midway  
between fully screwed in and fully screwed out.  
•
The carburetor governs the engine’s speed via the throttle  
control. Air and fuel are mixed in the carburetor. The air/  
fuel mixture is adjustable. Correct adjustment is essential  
to get the best performance from the machine.  
Do not attempt to adjust the L and H jets beyond either  
stop as this could cause damage.  
Now start the machine according to the starting  
instructions and let it warm up for 10 minutes.  
•
•
The setting of the carburetor means that the engine is  
adapted to local conditions, for example, the climate,  
altitude, fuel and the type of 2-stroke oil.  
Low speed jet L  
The carburetor has three adjustment controls:  
L = Low speed jet  
Try to find the highest idling speed, turning the low speed  
needle L clockwise respectively counter-clockwise.When the  
highest speed has been found, turn the low speed needle L 1/  
4 turn counter-clockwise.  
H = High speed jet  
T = Idle adjustment screw  
+ 1/4  
L
CAUTION! If the cutting attachment rotates when the engine  
is idling the idle adjustment screw T should be turned anti-  
clockwise until the cutting attachment stops.  
•
•
The L and H-jets are used to adjust the supply of fuel to  
match the rate that air is admitted, which is controlled with  
the throttle. If they are screwed clockwise the air/fuel ratio  
becomes leaner (less fuel) and if they are turned anti-  
clockwise the ratio becomes richer (more fuel). A lean  
mixture gives a higher engine speed and a rich mixture  
gives a lower engine speed.  
Fine adjustment of the idle speedT  
Adjust the idle speed using the idle adjustment screw T, if it is  
necessary to readjust. First turn the idle adjustment screw T  
clockwise until the cutting attachment starts to rotate. Then  
turn the screw anticlockwise until the cutting attachment  
stops. The idle speed is correctly adjusted when the engine  
will run smoothly in every position.The idle speed should also  
be well below the speed at which the cutting attachment starts  
to rotate.  
The T-screw regulates the throttle setting at idle speed. If  
the T-screw is turned clockwise this gives a higher idle  
speed; turning it anti-clockwise gives a lower idle speed.  
Basic setting  
•
The basic carburetor settings are adjusted during testing  
at the factory. The basic setting is richer than the optimal  
setting and should be maintained for the first few hours the  
machine is in use. The carburettor should then be finely  
adjusted. Fine adjustment should be carried out by a  
skilled technician.  
CAUTION! If the cutting attachment rotates when the engine  
is idling the idle adjustment screw T should be turned anti-  
clockwise until the cutting attachment stops.  
WARNING! If the idle speed cannot be adjusted so that the  
cutting attachment stops, contact your dealer/service  
workshop. Do not use the machine until it has been correctly  
adjusted or repaired.  
Rec. idle speed 2700 rpm  
Recommended max. speed: See theTechnical data section.  
English – 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
MAINTENANCE  
The muffler is designed to reduce the noise level and to direct  
High speed jet H  
the exhaust gases away from the operator. The exhaust  
gases are hot and can contain sparks, which may cause fire  
if directed against dry and combustible material.  
The high speed jet H affects the engine power, speed,  
temperature and fuel consumption. If the high speed jet H is  
set too lean (screwed in too far) the engine speed will be too  
high and cause engine damage. Do not let the engine run at  
full speed for more than 10 seconds.  
Some mufflers are equipped with a special spark arrestor  
mesh. If your machine has this type of muffler, you should  
clean the mesh at least once a week.This is best done with a  
wire brush.On mufflers without a catalytic converter the mesh  
should be cleaned weekly, or replaced if necessary. On  
mufflers fitted with a catalytic converter the mesh should be  
checked, and if necessary cleaned, monthly. If the mesh is  
damaged it should be replaced.  
Apply full throttle and turn the high speed jet H very slowly  
clockwise until the engine slows down. Then turn the high  
speed jet H very slowly anticlockwise until the engine starts to  
run unevenly. Now turn the high speed jet H slowly clockwise  
a little way until the engine runs smoothly.  
Note that the engine should not be under load when you  
adjust the high speed jet H.You should therefore remove the  
cutting attachment, nut, support flange and drive disc before  
adjusting the high speed jet H.  
If the mesh is frequently blocked, this can be a sign that the  
performance of the catalytic converter is impaired. Contact  
your dealer to inspect the muffler. A blocked mesh will cause  
the machine to overheat and result in damage to the cylinder  
and piston.  
The high speed jet H is adjusted correctly when the machine  
burbles a little. If the machine races then the setting is too  
lean. If the engine produces a lot of smoke and burbles a lot  
then the setting is too rich.  
CAUTION! Never use a machine with a defective muffler.  
H
WARNING! Mufflers fitted with catalytic  
converters get very hot during use and  
remain so for some time after stopping.This  
also applies at idle speed. Contact can result  
in burns to the skin. Remember the risk of  
fire!  
CAUTION! For optimum adjustment of the carburettor,  
contact a qualified dealer/service workshop that has a  
revolution counter at their disposal.  
!
Correctly adjusted carburetor  
When the carburetor is correctly adjusted the machine will  
accelerate without hesitation and burble a little at maximum  
speed. It is also important that the cutting attachment does  
not rotate at idle. If the low speed jet L is set too lean it may  
cause starting difficulties and poor acceleration.  
Cooling system  
If the high speed jet H is set too lean it will result in less power,  
less performance, poor acceleration and/or damage to the  
engine.  
To keep the working temperature as low as possible the  
machine is equipped with a cooling system.  
4
If both the L and H jets are set too rich it will results in  
acceleration problems or too low a working speed.  
3
2
Muffler  
CAUTION! Some mufflers are fitted with a catalytic  
converter. See chapter on Technical data to see whether your  
machine is fitted with a catalytic converter.  
1
The cooling system consists of:  
18 – English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
MAINTENANCE  
1
2
3
4
Air intake on the starter.  
Cleaning the air filter  
Fins on the flywheel.  
Remove the air filter cover and take out the filter. Wash it  
clean in warm, soapy water. Ensure that the filter is dry before  
refitting it.  
Cooling fins on the cylinder.  
Cylinder cover (directs cold air over the cylinder).  
Clean the cooling system with a brush once a week, more  
often in demanding conditions. A dirty or blocked cooling  
system results in the machine overheating which causes  
damage to the piston and cylinder.  
An air filter that has been in use for a long time cannot be  
cleaned completely.The filter must therefore be replaced with  
a new one at regular intervals. A damaged air filter must  
always be replaced.  
If the machine is used in dusty conditions the air filter should  
be soaked in oil.See instructions under the heading Oiling the  
air filter.  
Spark plug  
Oiling the air filter  
The spark plug condition is influenced by:  
•
•
Incorrect carburetor adjustment.  
An incorrect fuel mixture (too much or incorrect type of  
oil).  
Always use HUSQVARNA filter oil, art. no. 531 00 92-48.The  
filter oil contains a solvent to make it spread evenly through  
the filter.You should therefore avoid skin contact.  
•
A dirty air filter.  
These factors cause deposits on the spark plug electrodes,  
which may result in operating problems and starting  
difficulties.  
Put the filter in a plastic bag and pour the filter oil over it.  
Knead the plastic bag to distribute the oil. Squeeze the  
excess oil out of the filter inside the plastic bag and pour off  
the excess before fitting the filter to the machine. Never use  
common engine oil. This would drain through the filter quite  
quickly and collect in the bottom.  
If the machine is low on power, difficult to start or runs poorly  
at idle speed: always check the spark plug first before taking  
any further action. If the spark plug is dirty, clean it and check  
that the electrode gap is 0.5 mm (0,020"). The spark plug  
should be replaced after about a month in operation or earlier  
if necessary.  
Bevel gear  
The bevel gear is filled with the right quantity of grease at the  
factory. However, before using the machine you should check  
that the bevel gear is filled three-quarters full with grease.Use  
HUSQVARNA special grease.  
CAUTION! Always use the recommended spark plug type!  
Use of the wrong spark plug can damage the piston/cylinder.  
Check that the spark plug is fitted with a suppressor.  
Air filter  
The air filter must be regularly cleaned to remove dust and dirt  
in order to avoid:  
The grease in the bevel gear does not normally need to be  
changed except if repairs are carried out.  
•
•
•
•
•
Carburettor malfunctions  
Starting problems  
Loss of engine power  
CAUTION! Use only HUSQVARNA replacement parts. Use  
of other brands of replacement parts can cause damage to  
your unit or injury to the operator or others.Your warranty  
does not cover damage or liability caused by the use of  
accessories and/or attachments not specifically  
recommended by HUSQVARNA.  
Unnecessary wear to engine parts  
Excessive fuel consumption.  
Clean the filter every 25 hours, or more regularly if conditions  
are exceptionally dusty.  
English – 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
MAINTENANCE  
Maintenance schedule  
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the  
Maintenance section.  
Daily  
maintenance  
Weekly  
maintenance  
Monthly  
maintenance  
Maintenance  
Clean the outside of the machine.  
X
Make sure the throttle trigger lock and the throttle function correctly from a  
safety point of view.  
X
Check that the stop switch works correctly.  
Check that the cutting attachment does not rotate at idle.  
Clean the air filter. Replace if necessary.  
X
X
X
Check that the guard is undamaged and not cracked. Replace the guard if  
it has been exposed to impact or is cracked.  
X
X
Check that the trimmer head is undamaged and not cracked. Replace the  
trimmer head if necessary.  
Check that the locking nut of the cutting equipment is tighten correctly.  
Check that nuts and screws are tight.  
X
X
X
Check that there are no fuel leaks from the engine, tank or fuel lines.  
Check the starter and starter cord.  
X
X
Check that the vibration damping elements are not damaged.  
Clean the outside of the spark plug. Remove it and check the electrode  
gap. Adjust the gap to 0.5 mm (.20”), or replace the spark plug. Check that  
the spark plug is fitted with a suppressor.  
X
Clean the machines cooling system.  
X
X
X
X
Clean or replace the spark arrestor mesh on the muffler (only applies to  
mufflers without a catalytic converter).  
Clean the outside of the carburettor and the space around it.  
Check that the bevel gear is filled three-quarters full with lubricant. Fill if  
necessary using special grease.  
Check the fuel filter from contamination and the fuel hose from cracks or  
other defects. Replace if necessary.  
X
X
X
Check all cables and connections.  
Check the clutch, clutch springs and the clutch drum for wear. Replace if  
necessary by an autorized service workshop.  
Replace the spark plug. Check that the spark plug is fitted with a  
suppressor.  
X
X
Check and clean the spark arrestor mesh on the muffler (only applies to  
mufflers fitted with a catalytic converter).  
20 – English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TECHNICAL DATA  
Technical data  
223L  
Engine  
3
Cylinder displacement, cu.in/cm  
Cylinder bore, inch/mm  
Stroke, inch/mm  
1,50/24,5  
1,34/34,0  
1,06/27  
2700  
Idle speed, rpm  
Recommended max. fast idle speed, rpm  
Speed of output shaft, rpm  
11000-11700  
8014  
Max. engine output, acc. to ISO 8893, kW/ rpm  
Catalytic converter muffler  
Speed-regulated ignition system  
Ignition system  
0,75/9000  
Yes  
No  
Manufacturer/type of ignition system  
Spark plug  
Walbro MB  
Champion RCJ 7Y/  
NGK BPMR 7A  
Electrode gap, inch/mm  
Fuel and lubrication system  
Manufacturer/type of carburetor  
Fuel tank capacity, US pint/litre  
Weight  
0,02/0,5  
Zama C1Q  
1,06/0,5  
Weight without fuel, cutting attachment and guard, Lbs/kg  
Sound levels  
9,0/4,1  
(see note 1)  
Equivalent sound pressure level at the user′s ear, measured  
according to ANSI B175.3-2003, dB(A), min/max:  
91/98  
Vibration levels  
Vibration levels at handles, measured according to ANSI  
2
B175.3-2003, m/s  
At max. speed, front/rear handles, min:  
At max. speed, front/rear handles, max:  
3,9/5,9  
9,7/13,5  
Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various  
working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.  
NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting  
equipment fitted. The table indicates the highest and lowest values.  
223L  
Approved accessories  
Arbor shaft thread M10  
Plastic blades  
Type  
Cutting attachment guard, Art. no.  
Tricut Ø 300 mm  
Trimmy Fix  
T25  
503 93 42-02  
Trimmer head  
503 93 42-02  
503 93 42-02  
T35  
503 93 42-02  
S35  
503 93 42-02  
Approved accessories  
Art No.  
Cutting attachment guard, Art. no.  
J-handle set including grass blade Grass 255-4 1”  
(Ø 255 4-teeth)  
537 04 85-04  
503 93 42-02  
English – 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
FEDERAL EMISSION CONTROL WARRANTY STATEMENT  
your warranty rights and responsibilities, you should contact  
your nearest authorized servicing dealer or call Husqvarna  
YOUR WARRANTY RIGHTS AND  
OBLIGATIONS  
Forest & Garden at 1-800-487-5963.  
WARRANTY PERIOD Any warranted part which is not  
scheduled for replacement as required maintenance, or  
which is scheduled only for regular inspection to the effect of  
“repair or replace as necessary” shall be warranted for 2  
years.Any warranted part which is scheduled for replacement  
as required maintenance shall be warranted for the period of  
time up to the first scheduled replacement point for that part.  
The EPA (The US Environmental Protection Agency),  
Environment Canada and Husqvarna Forest & Garden are  
pleased to explain the emissions control system warranty on  
your 2001 and later small nonroad engine. In U.S. and  
Canada, new small nonroad engines must be designed, built  
and equipped to meet the federal stringent anti-smog  
standards. Husqvarna Forest & Garden must warrant the  
emission control system on your small nonroad engine for the  
period of time listed below provided there has been no abuse,  
neglect or improper maintenance of your unit.Your emission  
control system includes Parts such as the carburetor and the  
ignition system. Where a warrantable condition exists,  
Husqvarna Forest & Garden will repair your small nonroad  
engine at no cost to you. Expenses covered under warranty  
include diagnosis, parts and labor.  
DIAGNOSIS The owner shall not be charged for diagnostic  
labor which leads to the determination that a warranted part  
is defective, if the diagnostic work is performed at an  
approved Husqvarna Forest & Garden servicing dealer.  
CONSEQUENTIAL DAMAGES Husqvarna Forest & Garden  
may be liable for damages to other engine components  
caused by the failure of a warranted part still under warranty.  
WHAT IS NOT COVERED  
All failures caused by abuse, neglect or improper  
maintenance are not covered.  
MANUFACTURER′S WARRANTY  
COVERAGE  
The 2001 and later small nonroad engines are warranted for  
two years. If any emission related part on you engine (as  
listed above) is defective, the part will be repaired or replaced  
by Husqvarna Forest & Garden.  
ADD -ON OR MODIFIED PARTS  
The use of add-on or modified parts can be grounds for  
disallowing a warranty claim. Husqvarna Forest & Garden is  
not liable to cover failures of warranted parts caused by the  
use of add-on or modified parts.  
OWNER′SWARRANTY RESPONSIBILITIES  
As the small nonroad engine owner, you are responsible for  
the performance of the required maintenance listed in your  
Operator′s Manual. Husqvarna Forest & Garden  
HOW TO FILE A CLAIM  
If you have any questions regarding your warranty rights and  
responsibilities, you should contact your nearest authorized  
servicing dealer or call Husqvarna Forest & Garden at 1-800-  
487-5963.  
recommends that you retain all receipts covering  
maintenance on your small nonroad engine, but Husqvarna  
Forest & Garden cannot deny warranty solely for the lack of  
receipts or for your failure to ensure the performance of all  
scheduled maintenance. As the small nonroad engine owner,  
you should, however, be aware that Husqvarna Forest &  
Garden may deny you warranty coverage if your small  
nonroad engine or a part of it has failed due to abuse, neglect,  
improper maintenance, unapproved modifications or the use  
of parts not made or approved by the original equipment  
manufacturer.You are responsible for presenting your small  
nonroad engine to a Husqvarna Forest & Garden authorized  
servicing dealer as soon as a problem exists. The warranty  
repairs should be completed in a reasonable amount of time,  
not to exceed 30 days. If you have any questions regarding  
your warranty rights and responsibilities, you should contact  
your nearest authorized servicing dealer or call Husqvarna  
Forest & Garden at 1-800-487-5963.  
WHERE TO GET WARRANTY SERVICE  
Warranty services or repairs shall be provided at all  
Husqvarna Forest & Garden authorized servicing dealers.  
MAINTENANCE, REPLACEMENT AND  
REPAIR OF EMISSION-RELATED PARTS  
Any Husqvarna Forest & Garden approved replacement part  
used in the performance of any warranty maintenance or  
repairs on emission-related parts, will be provided without  
charge to the owner if the part is under warranty.  
EMISSION CONTROL WARRANTY PARTS  
LIST  
WARRANTY COMMENCEMENT DATE  
The warranty period begins on the date small nonroad engine  
is delivered.  
1
2
3
4
Carburetor and internal parts  
Intake pipe, airfilter holder and carburetor bolts.  
Airfilter and fuelfilter covered up to maintenance schedule.  
Ignition System  
LENGTH OF COVERAGE  
1
2
Spark Plug, covered up to maintenance schedule  
Ignition Module  
Husqvarna Forest & Garden warrants to the initial owner and  
each subsequent purchaser that the engine is free from  
defects in materials and workmanship which cause the failure  
of a warranted part for a period of two years.  
5
Muffler with catalytic converter  
MAINTENANCE STATEMENT  
The owner is responsible for the performance of all required  
maintenance, as defined in the operator’s manual.  
WHAT IS COVERED  
REPAIR OR REPLACEMENT OF PARTS Repair or  
replacement of any warranted part will be performed at no  
charge to the owner at an approved Husqvarna Forest &  
Garden servicing dealer. If you have any questions regarding  
English – 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Download from Www.Somanuals.com. All Manuals Search And Download.  
T25  
1
2
3
6,0 m  
18'  
10 cm  
4"  
3,05 m  
9'  
4
5
7
6
8
"Clic"  
15 cm  
6"  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
T35  
1
2
3
8,5 m  
28'  
10 cm  
4"  
4,3 m  
14'  
4
5
7
6
8
"Clic"  
15 cm  
6"  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
S35  
1
2
3
8,5 m  
28'  
10 cm  
4"  
4,2 m  
14'  
4
5
7
6
8
"Clic"  
10  
11  
15 cm  
6"  
´®z+R'=¶5Q¨  
´®z+R'=¶5Q¨  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S35  
1
2
4,25 m  
14'  
4,25 m  
14'  
4
3
5
15 cm  
6"  
B
A
15 cm  
6"  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1150072-95  
´®z+R'=¶5Q¨  
´®z+R'=¶5Q¨  
2006-01-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Greenheck Fan Ventilation Hood TAUB CA User Manual
Grindmaster Coffeemaker 83010 User Manual
Grizzly Drill G1008 User Manual
Hotpoint Washer Dryer WMUD 10637 User Manual
HP Hewlett Packard Switch HP J3175A User Manual
Huawei Network Router B686 User Manual
Huey Chiao Bluetooth Headset HCB70 User Manual
Husqvarna Lawn Mower Z 42 User Manual
Image Hot Tub IMHS40090 User Manual
Image Treadmill IMTL391052 User Manual