Main Menu - LENS
Menu [SHUTTER] - SHUTTER AUTO
Main Menu - LANGUAGE
Main Menu - RESET
Design and specifications are
subject to change without notice.
/
Rev 0 06 03
P/N:3810-0104C
1) LENS setup
1) SHUTTER setup (for LENS MANUAL)
1) LANGUAGE setup
1) RESET
SETUP
CAMERA ID
LENS
①
①
①
①
Press LEFT or RIGHT button in LENS on
Main Menu to select the mode to
Press LEFT or RIGHT button in SHUTTER
to select the mode to
DEFAULT value - ENGLISH
Select RESET.
OFF
Series
HD73
Press MENU button.
DC ↙
FIXED ↙
ATW
↙
↙
↙
↙
↙
SHUTTER
WHITE BAL.
FUNCTION
ADJUST
LANGUAGE
RESET
MANUAL ◀ ▶ VIDEO ◀ ▶ DC
.
AUTO
◀ ▶ FLK ◀ ▶ FIXED
The screen on the bottom appears.
②
SETUP
CAMERA ID
LENS
SHUTTER
WHITE BAL.
FUNCTION
ADJUST
LANGUAGE
RESET
After selecting LANGUAGE,
change setting using LEFT or RIGHT button.
↙
◀ ▶MANUAL
.
LENS DC
SHUTTER AUTO
OFF
!
②
③
DC ↙
FIXED ↙
ATW
↙
↙
Select YES or NO.
↙
Setting Mode : DC
Operation Manual
!
↙
Setting Mode : FIXED
ENGLISH
↙
③
Choose the language mode you
wish to operate in.
BRIGHTNESS
056
BRIGHTNESS
056
Select YES to reset your camera
to default factory condition
Vandal-Resistant
Dome Camera
EXIT
2) DC LENS setup
ENGLISH
↙
①
②
③
↙
Press MENU button in DC
screen on the right side.
to display the
↙
:
RETURN
↙
:
RETURN
EXIT
LOAD DEFAULT
s
Use LEFT, RIGHT button to change
BRIGHTNESS(IRIS LEVEL) value.
!
YES
NO
ENGLISH ◀ ▶ Korean ◀ ▶ Chinese1 ◀ ▶ Chinese 2 ◀ ▶ Japanese
Need Help?
Press MENU button to return to the previous screen.
Call 1.800.796.CCTV for sales, service and customer support.
READ AND KEEP THIS
OPERATION MANUAL
16
18
20
22
24
26
28
30
17
19
21
23
25
27
29
31
32
33
35
37
39
. User Information
9. SPECIFICATIONS
3
-
Axis
Menu [SHUTTER] - FIXED Mode Setup
Menu [WHITE BAL.] - WHITE BALANCE Mode Setup
3
-
Axis
INFORMATION
↙
MODEL
HD73
HD73X
1) FIXED
setup (MANUAL,DC,VIDEO LENS)
1) WHITE BALANCE setup
BLC, AGC
ON / OFF (Level Adjustable)
CAUTION
SHUTTER FIXED
AWB FIXED
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.
①
↙
①
Signal System
Image Sensor
Effective Pixels
Video Output
NTSC
PAL
Day & Night
Auto (ICR)
ON / OFF (4 Programmable Zone)
ON / OFF (Horizontal)
Press MENU button in FIXED
In WHITE BAL., press LEFT, RIGHT button
to select the mode you wish to operate
RISK OF ELECTRIC SHOCK
DO NOT OPEN
to display the screen on the right side.
2:1 Interlace Transfer 1/3 Inch Super HAD CCD
768(H) x 494(V) 752(H) x 582(V)
Composite: 1.0Vp-p, 75Ω, Unbalanced
Privacy
↙
ATW ◀ ▶ AWB ◀ ▶ FIXED
↙
◀ ▶MANUAL
.
Mirror
SHUTTER M : 1/60
AWB FIXED : MODE 1
②
Press LEFT or RIGHT button in SHUTTER.
Can be set in ([NTSC: 1/60 ~ 1/100,000]
[PAL: 1/50 ~ 1/100,000]) range.
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
Gamma
User / 0.5 ~ 1.0 Adjustable
ON / OFF (64 Programmable Zone)
0 ~ 255 (Level Adjustable)
0 ~ 31 (Level Adjustable)
DC Iris
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Sync. System
Luminance S/N Ratio
Horizontal Resolution
Min. Illumination (F1.2)
Lens
Internal Sync
More than 50dB (AGC OFF)
530 TV Lines
Motion Detection
Contrast
↙
2) FIXED
setup
↙
:
RETURN
↙
:
RETURN
Explanation of two Symbols
①
Can set from MODE 1 to MODE 4.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Sharpness
WARNING
0.3 Lux(30IRE, AGC ON), 0 Lux(IR LED)
DC Auto IRIS Vari-focal (f=3.8~9.5mm)
Manual
Applicable Lens
Supply Voltage
Power Consumption
Operating Temperature
Storage Temperature
Dome Size (Ø)
Weight
↙
3) MANUAL
setup
AWB MANUAL
The manufacturer could void the user's authority to operate the equipment.
12VDC (10V~15V)
①
As shown on the lower right picture,
set Red and Blue color value temperature.
RED
113
255
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance-
(servicing) instructions in the literature accompanying the appliance.
CAUTION - To prevent electric shock and risk of fire hazards:
Do NOT use power sources except for that specified.
Do NOT expose this appliance to rain or moisture.
Focus
Max. 4.5W / 360mA
BLUE
Electronic Shutter
White Balance
Camera ID
1/60~1/100,000
1/50~100,000
-10℃~+50℃ (Recommendation: -5℃~+40℃)
②
Press MENU button in RETURN
to exit from setup mode.
ATW (1,800˚K~10,500˚K) / AWB / Fixed / Manual
ON / OFF
-20℃~+60℃
100 mm
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"
↙
:
RETURN
This installation should be made by a qualified service person and should abide to all local codes.
Language
English / Korean / Chinese 1 / Chinese 2 / Japanese
Approx. 844g
2
3
5
7
9
34
. Contents
1. SAFETY INSTRUCTIONS
10. TROUBLESHOOTING
. Memo
3-
Axis
3
-
Axis
Axis
Axis
Axis
Main Menu - FUNCTION
Menu [FUNCTION] - BLC 1
3-
Axis
3-Axis
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
↙
1) FUNCTION
setup
1) BLC SETUP MODE
Thank you for purchasing this COLOR VIDEO CAMERA.
BLC SETUP
Read Instructions
Read all of the safety and operating instructions
Installation
①
①
↙
Press MENU button in FUNTION
Press MENU button in BLC ON
,
Before using this camera, please read this operation manual carefully to obtain
the best result and keep this manual for future reference.
Do not place this product on an unstable cart, stand,
or table. The product may fall causing serious injury
to a child or adult, and damage to the product.
Use only with a cart or stand recommended by the
manufacturer, or sold with the product.
Mounting should follow the manufacturer's instructions,
and should use a mounting accessory recommended
by manufacturer.
to show the OSD display on the right.
to display the screen on the right side.
P r o b l e m
S o l u t i o n s
BLC AREA ↙
before using the product.
FUNCTION
Nothing appears on the
screen.
• Check that the power cord and line connection between the camera and monitor
are fixed properly.
• Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
BLC RATIO
RETURN
16
BLC
AGC
OFF
ON ↙
OFF
OFF
0.45
OFF
Retain Instructions
Save this instructions for later use.
↙
2) Select item using UP, DOWN button.
3) Set details using LEFT, RIGHT button.
4) Click "Return" to go to MAIN SETUP
2) BLC AREA
setup
①
②
③
PRIVACY
MIRROR
GAMMA
MOTION
RETURN
Use UP, DOWN, LEFT, RIGHT button
to move the AREA setup position.
• Is lens stained with dirt? Clean your lens with soft, clean cloth.
• Set the monitor to proper condition.
• If the camera is exposed to too strong light, change the camera position.
• Adjust the lens' focus properly.
The image on the screen
is dim.
...........
........................
...........
1. SAFETY INSTRUCTIONS
5
6
7
8
9
6. CONNECTIONS
10
11
12
34
36
Cleaning
..........................
2. PRECAUTIONS
7. NAME AND FUNCTIONS
Unplug this appliance from wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Set or release BLC AREA
using MENU button.
The image on the screen
is dark.
• Adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75Ω/ Hi-z properly.
• Adjust DC Level, on the OSD menu.
................................
..........................
...............
3. FEATURES
8. OPERATING CAMERA
Power source
Press MENU button for more than 1 second
to move to BLC AREA MODE.
The camera is not working
properly, and the surface
of the camera is hot.
• Check that you have properly connected the camera to an appropriate power source.
......................
Water and Moisture.
This product should be operated only from the type
of power source indicated on the marking label.
If you are not sure of the type of power supplied to
your home, consult your dealer or local power
company.
4. COMPOSITION
5. INSTALLATION
9. SPECIFICATIONS
Do not use this product near water or moisture.
(For example. near a bathtub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool,etc)
..........................
...............
• Is the camera facing to direct sunlight or fluoresent lighting?
Change the camera position.
The image on the screen
flickers.
10. TROUBLESHOOTING
4
36
2. PRECAUTIONS
3. FEATURES
3-
Axis
3-
Menu [FUNCTION] - BLC 2
Menu [FUNCTION] - BLC 3
1) BLC AREA MODE
1) BLC RATIO setup (BLC LEVEL value setup)
High Sensitivity 1/3 Inch Sony Super HAD CCD
①
①
Exit from BLC AREA MODE
Use UP,DOWN button
to move to BLC RATIO.
Handling
to move to BLC SETUP MODE screen.
Min. Illumination (F1.2, 30 IRE) : 0.3 Lux (Color)
Do not disassemble the camera and never touch
parts inside the camera.
Be sure the ambient temperature is less than
40℃ in installation intended for long term
continuous operation.
BLC SETUP
0.0 Lux (IR LED On)
②
Use LEFT, RIGHT button
to change BLC LEVEL value (0~63)
0:MIN , 63:MAX
BLC AREA
2) BLC OSD description
BLC AREA ↙
ALL CLEAR
ALL SET
RETURN
EXET
Do not drop the camera or subject it to shocks
and vibrations to avoid possible damage.
Day & Night (ICR)
①
②
③
④
ALL CLEAR - Clear all set AREA
BLC RATIO
RETURN
16
Avoid installing in a humid or dusty place.
OSD (On Screen Display)
High Performance Menus For Functions
③
Press MENU button in RETURN
to move to FUNCTION MODE.
When attaching or removing the lens, handle
with care in order to that moisture and dust do
not enter the camera.
ALL SET - Set all 64 BLC AREA
Avoid installing in places where there are
strong magnetic fields and electric signals.
RETURN - Return to BLC AREA setup mode.
• Privacy Zone Selectable (4 Programmable Zone)
• Motion Detection Selectable (64 Programmable Zone)
• Sharpness Enhanced Adjustable
• Flickerless Selectable
• Gamma Enhanced Selectable
Avoid installing in places where the camera
would be subject to strong vibrations.
EXIT - Save AREA and return to
Installation and storage
BLC SETUP MODE.
Never expose the camera to rain and water.
Do not point the camera at the sun. This could
damage the camera whether it is operating or not.
Do not install the camera where the temperature
could exceed the allowable range.
• BLC Zone Selectable (64 Programmable Zone)
6
38
4. COMPOSITION
5. INSTALLATION
3-
Axis
3-
Menu [FUNCTION] - AGC
Menu [FUNCTION] - PRIVACY
1) AGC setup
1) PRIVACY setup
Ceiling
FUNCTION
Stick the guide pattern on the wall or ceiling.
1
2
①
↙
①
②
③
AGC default setting ON
Default setting OFF - Use LEFT,RIGHT button.
↙
Change setup to ON
mode.
BLC
AGC
ON ↙
ON ↙
ON ↙
OFF
0.45
OFF
Guide Pattern
Dome Base
Drill four holes according to the guide pattern
then insert anchors into the drilled holes.
↙
After ON
mode setup, 4 AREA groups are
configured as displayed on the right-side picture.
AGC CONTROL
②
↙
Press MENU button in ON
PRIVACY
MIRROR
GAMMA
MOTION
RETURN
to display the screen on the right side.
L-Wrench
Press MENU button.
Details of each area is dsplayed.
Guide Pattern
Draw out power / video wires to the
connecting places.
3
③
④
095
AGC GAIN
Use LEFT, RIGHT button
to adjust AGC GAIN value (0~255)
0:MIN , 255:MAX
Operation Manual
2) PRIVACY details setup
Fixed the camera to a celling using four screws.
4
5
↙
:
RETURN
①
②
③
④
⑤
⑥
⑦
Select AREA SEL - PRIVACY 0~3.
Mounting
Screw
PRIVACY
Press MENU button to return
to the previous screen.
Adjust desired focus and scene by turning and
moving the 3-axis camera bracket by hand.
AREA STATE - 0~3 AREA ON/OFF
Mounting Screw
AREA SEL
AREA STATE
LEFT
RIGHT
TOP
BOTTOM
COLOR
RETURN
AREA 0
ON
017
058
020
LEFT - Change left portion of each AREA size.
RIGHT - Change right portion of each AREA size.
TOP - Change top portion of each AREA size.
BOTTOM - Change bottom portion of each AREA size.
COLOR - Change entire color of the AREA (16 COLOR)
Dome Cover
L-Wrench
Put the dome cover over the base.
6
7
055
001
Service Monitor Cable
Fix the dome cover on the base by L-Wrench.
8
6. CONNECTION
7. NAME AND FUNCTIONS
3-
Axis
3-
Menu [FUNCTION] - MIRROR
Menu [FUNCTION] - GAMMA
4
5
1) MIRROR setup
1) GAMMA setup (DEFAULT 0.45)
FUNCTION
FUNCTION
①
①
MIRROR default setting OFF
In FUNCTION MODE,
BLC
AGC
OFF
ON ↙
OFF
OFF
0.45
OFF
BLC
AGC
OFF
ON ↙
OFF
OFF
0.45
OFF
ON setting - Use LEFT, RIGHT button.
use UP, DOWN button to select GAMMA.
6
7
Video
Video Output
GND
PRIVACY
MIRROR
GAMMA
MOTION
RETURN
PRIVACY
MIRROR
GAMMA
MOTION
RETURN
#
1
2
②
②
(Yellow)
Left and Right side is switched
as shown on the picture.
Use LEFT, RIGHT button
to adjust GAMMA value.
1
(USER ◀ ▶ 0.05 ◀ ▶ 0.10 ◀ ▶ 0.15 ~ 1.0)
3
2
Power- 12VDC
(Red)
#
Camera Lay-out
• The wire is polarized.
• Use 12V DC power source.
OFF
ON
1
2
3
4
5
6
7
Tilt rotation: Adjusting the vertical angle.
Pan rotation: Adjusting the horizontal angle.
Horizontal rotation: Adjusting the horizontal position of the screen.
Focus handle: Focus (Far or Near)
Zoom handle: Zoom (Tele or Wide)
IR LED(3.8mm~9.5mm): 850nm/ 30°(20EA), Power Consumption(4.5W)
No. Function Terminal Color
R e m a r k
1.0 Vp-p
#1 Video Output
#2 Power Input
Yellow
Red
12VDC (10V~15V), 360mA (Max)
Sensor
10
11
13
15
8. OPERATING CAMERA
3-
Axis
Setting up the Menu
Menu [FUNCTION] - MOTION
Menu [FUNCTION] - MOTION AREA 1
!
1) MOTION DETECTION setup
1) MOTION AREA setup
Push the Joy stick for one second, and the OSD
appears on the screen. Move the Joy Stick up, down,
left & right to control the OSD functions.
FUNCTION
SETUP
①
②
③
①
DEFAULT value OFF
Use UP, DOWN, LEFT, RIGHT button
to move AREA setting position.
S E T U P M E N U
BLC
AGC
OFF
ON ↙
OFF
OFF
0.45
OFF
- Push and hold MENU button 1 second
to access the setup mode.
↙
In ON
, press MENU button.
CAMERA ID
LENS
• ON
• OFF
PRIVACY
MIRROR
GAMMA
MOTION
RETURN
②
③
Use MENU button to set and release AREA.
Display MOTION details.
• MANUAL
• AUTO
• VIDEO
• DC
• Select the status using the
joystick. (up, down, left, right)
UP
SW1
SHUTTER
WHITE BAL.
FUNCTION
• FLK
• FIXED
• FIXED
• MANUAL
• MANUAL
• PRIVACY
• MOTION
Press MENU button for more than 1 second
to move to MOTION AREA MODE
MENU(SET):
↙
2) AREA
setup
SET BY JOY STICK
LEFT
RIGHT
• ATW
• AWB
①
↙
In AREA , press MENU button. (see p.29)
SETUP
• BLC
• AGC
CAMERA ID
LENS
OFF
2) MOTION AREA MODE
3) MOTION TH. Setup
J601
• MIRROR
• CONTRAST
• GAMMA
DC ↙
FIXED ↙
ATW
↙
↙
DOWN
MOTION
①
You will return to MOTION AREA MODE
after "Exit" from MOTION AREA MODE.
①
Set motion sensitivity 0(MAX)~255(MIN)
SHUTTER
WHITE BAL.
FUNCTION
ADJUST
LANGUAGE
RESET
MOTION AREA
ADJUST
• SHARPNESS
AREA ↙
ALL CLEAR
ALL SET
RETURN
EXET
_
_
4) MOTION TRACE setup
• CB GAIN
• CR GAIN
MOTION TH.
MOTION TRACE
RETURN
037
OFF
Service Monitor Connecter:
Use service monitor
connector to set camera angle
& focus when installing.
①
ON : Display motion detection AREA.
LANGUAGE
RESET
• ENGLISH • KOREAN • CHINESE1 • CHINESE2 • JAPANESE
ENGLISH
↙
J613
UP SW1
!
J611
LEFT
RIGHT
Setting value can be adjusted
EXIT
using LEFT or RIGHT button.
EXIT
DOWN
12
Main Menu - SETUP
Main Menu - CAMERA ID
Menu [FUNCTION] - MOTION AREA 2
Main Menu - ADJUST
1) CAMERA ID setup (default setting OFF)
1) MOTION OSD description
1) ADJUST setup
①
②
!
Press MENU button in ADJUST.
①
↙
①
②
③
④
Press MENU key in ON
(Access ID setting MODE)
state.
ALL CLEAR - Release all set AREA
1. Press MENU button, then SETUP mode is activated.
Move to screen on the right side.
• MAIN SETUP menu is displayed on the monitor.
ALL SET - Set all 64 MOTION AREA.
ID SETUP
ADJUST
②
③
Press MENU key in CAMERA ID.
Each LEVEL value can be
SETUP
CAMERA ID
LENS
SHUTTER
WHITE BAL.
FUNCTION
ADJUST
LANGUAGE
RESET
CONTRAST
083
12
RETURN - Return to MOTION AREA Setup Mode.
EXIT - Save AREA and return to MOTION SETUP MODE.
adjusted using LEFT, RIGHT button.
OFF
CAMERA ID
Character is changed each time UP, DOWN is
pressed. (Can select up to 63 letters)
2. Select OSD item using UP, DOWN button.
3. Set details using LEFT, RIGHT button.
DC ↙
FIXED ↙
ATW
↙
↙
SHARPNESS
A
_
↙
C
_
CB GAIN
190
205
2) CONTRAST setup
④
⑤
↙
Press MENU button in
exit from ID setup mode
to
POSITION
RETURN
①
Adjust Y-gain value (0~255)
_
CB GAIN
ENGLISH
↙
Press MENU button in 'C' to correct and erase
the chosen entry.
RETURN
3) SHARPNESS setup
4. Select "Exit" and then press the MENU button
to finish the SETUP (Save and Exit)
EXIT
①
Adjust aperture value (0~31)
2) POSITION setup. Press POSITION ↙.
_
4) CB GAIN setup
①
②
③
Move the character using UP, DOWN, LEFT, RIGHT button.
Press Menu button to confirm selection of the character.
_
①
Adjust COLOR CB GAIN value (0~255)
_
5) CR GAIN setup
Press Return to go to previous screen. ID is displayed by pressing EXIT on MAIN MENU.
_
①
Adjust COLOR CR GAIN value (0~255)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|