HX3
Wearable Computer
®
With Microsoft Windows CE 5.0 Operating System
Quick Start Guide
HX3-QS Rev A
4/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Components - Front
Download from Www.Somanuals.com. All Manuals Search And Download.
Components - Back
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach Audio/Power Cable to HX3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect Battery and Audio Cable
Download from Www.Somanuals.com. All Manuals Search And Download.
Trigger Rotation
Attach Ring to Finger
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach Ring Cable to HX3
Download from Www.Somanuals.com. All Manuals Search And Download.
Voice Pouch, Headset and Ring Scanner
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternative Battery Placement
Scanning a Bar Code
Download from Www.Somanuals.com. All Manuals Search And Download.
Desktop Cradle
Battery Multi-Charger
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove Trigger Module
Remove Ring Strap Module
Replace Ring Strap Module
Replace Trigger Module
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the HX3
Please have the following Information available before setting up your HX3:
l
l
Network ID (SSID) of the Access Point
WEP key or LEAP authentication credentials
1. Connect a fully charged battery to the HX3.
2. Press the Power button.
3. Connect via ActiveSync
4. Copy LXEConnect files to PC.
5. Install and launch LXEConnect
6. Accept the EULA.
7. Set the date and time.
8. Edit the radio parameters.
9. Perform a reboot.
Bluetooth and HX3
Please refer to the HX3 Reference Guide for information when using the HX3 with
Bluetooth.
ActiveSync
Installing ActiveSync on Desktop/Laptop
ActiveSync (version 4.5 or higher for Windows XP desktop/laptop computers) must be
resident on the host (desktop/laptop) computer. Windows Mobile Device Center is
required for a Windows Vista/Windows 7 desktop/laptop computer. ActiveSync and
Windows Mobile Device Center for the PC are available from the Microsoft website.
Follow Microsoft's instructions to locate, download and install ActiveSync or Windows
Mobile Device Center on your desktop/laptop.
ActiveSync using USB-Client Connection
The only connection type is USB Client.
1. Connect the HX3 end of the cable to the connector on the bottom of the HX3.
2. Connect the USB type A connector on the I/O cable to a USB port on a PC or
laptop.
ActiveSync starts automatically when the USB cable is connected.
When the HX3 loses connection, the connection to ActiveSync is lost. Disconnect the
PC end of the cable and re-connect.
Please refer to the HX3 Reference Guide for ActiveSync information.
Download from Www.Somanuals.com. All Manuals Search And Download.
LXEConnect
Install LXEConnect
1. Establish an ActiveSync connection between the HX3 and a laptop/desktop.
2. Select Explore (ActiveSync) or File Management (Windows Mobile Device
Center) from the PC interface.
3. Browse to the \System\LXEConnect folder on the HX3 using the explorer
dialog box.
4. Copy the LXEConnect.msi and Setup.exe files from the HX3 to the PC.
5. Close the explorer dialog box.
6. Execute the Setup.exe file that was copied to the PC.
7. Follow the on screen prompts to install LXEConnect.
Using LXEConnect
1. Establish an ActiveSync connection to the HX3 if one does not exist.
2. Launch LXEConnect from the PC by selecting Start > Programs > LXE >
LXEConnect.
3. LXEConnect launches and displays the HX3 desktop.
4. The HX3 can be configured from the LXEConnect window. Input from the
PC's keyboard and mouse are recognized as if they were attached to the
HX3.
5. Click the OK button to dismiss the About CERDisp dialog box. The dialog box
automatically times out after approximately 30 seconds if no action is taken.
6.
If any parameter changes were made, warmboot the HX3 by clicking
>
Run. Type warmboot and click OK.
7. Select File > Exit or click the X in the upper right hand corner to close
LXEConnect and then disconnect the ActiveSync session.
Warmbooting the HX3 terminates the ActiveSync connection. To make additional
changes to the HX3, reconnect the ActiveSync cable and launch LXEConnect again.
Rebooting the HX3
Using the Start menu, select Start > Run and type warmboot in the text box. Press
Enter.
When the HX3 is booting, there may be small delays while the wireless client connects,
applications launch, remote management completes and Bluetooth devices connect.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Radio
If the access point uses an authentication protocol (WEP, LEAP, etc.), your radio must
use the same authentication. Please contact your IT department for WEP keys or LEAP
credentials. Please refer to the HX3 Reference Guide for information on using WPA.
1. Tap Start > Programs > Summit > SCU OR tap the Summit Client Utility
icon on the desktop.
2. Tap the Admin Login button and enter the password (default = SUMMIT).
3. Tap the Profile tab and make sure the Default profile is selected.
4. Select SSID and enter your SSID value.
5. If the access point is using WEP, select WEP from the Encryption pull down
list.
6. Tap the WEP keys/PSKs button and enter the WEP Key(s) and tap OK. Skip
to step 12.
7. If the access point is using LEAP, select LEAP from the EAP Type pull down
list.
8. Select WEP EAP from the Encryption pull down list.
9. If the Cisco/CCS certified AP is configured for open authentication, set the
Auth Type radio parameter to Open.
10. If the AP is configured for network EAP only, set the Auth Type radio
parameter to LEAP.
11. Tap the Credentials button and enter the User Name and Password.
12. Tap the Commit button to save the radio configuration.
13. Tap the Main tab. Wait for a radio connected message.
14. Tap the Admin Logout button when finished.
15. Reboot the HX3.
Please refer to the Radio Mode parameter in the HX3 Reference Guide. It is important
that this parameter setting corresponds to the Access Point to which the HX3
connects.
Download from Www.Somanuals.com. All Manuals Search And Download.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in specifications
and other information contained in this document without prior notice, and the reader
should in all cases consult HII to determine whether any such changes have been
made. The information in this publication does not represent a commitment on the part
of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor
for incidental or consequential damages resulting from the furnishing, performance, or
use of this material.
This document contains proprietary information that is protected by copyright. All rights
are reserved.
© 2007-2012 Honeywell International Inc. All rights reserved.
Other product names or marks mentioned in this document may be trademarks or
registered trademarks of other companies and are the property of their respective
owners.
Web Address: www.honeywellaidc.com
Patents
Technical Assistance
Contact information for technical support, product service, and repair can be found at
Limited Warranty
information.
User Documentation
Download from Www.Somanuals.com. All Manuals Search And Download.
|