Honeywell Camcorder HXMT9 HXMT9X User Manual
9-Channel  
Black&White Multiplexer  
HXMT9 / HXMT9X  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING:  
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT  
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.  
DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION  
GRILLS.  
WARNING  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER(OR BACK).  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
Explanation of Graphical Symbols  
The lightning flash with arrowhead symbol, within an equilateral  
triangle, is intended to alert the user to the presence of  
uninsulated "dangerous voltage" within the product's enclosure  
that may be of sufficient magnitude to constitute a risk of  
electric shock to persons.  
The exclamation point within an equilateral triangle is intended  
to alert the user to the presence of important operating and  
maintenance (servicing) instructions in the literature  
accompanying the product.  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Precautions  
Should any liquid or solid object fall into the cabinet, unplug the unit and  
have it checked by qualified personnel before operating it any further.  
Unplug the unit from the wall outlet if it is not going to be used for several  
days or more. To disconnect the cord, pull it out by the plug. Never pull  
the cord itself.  
Allow adequate air circulation to prevent internal heat build-up. Do not  
place the unit on soft surfaces (rugs, carpets, sofas, etc.) or near  
materials (curtains, draperies) that may block the ventilation holes.  
Height and vertical linearity controls located on the rear panel are for  
special adjustments by qualified personnel only.  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFEGUARDS  
1. READ INSTRUCTIONS – Read the safety and operating instructions before  
operating the unit.  
2. RETAIN INSTRUCTIONS – Retain the safety and operating instructions for  
future reference.  
3. CLEANING – Unplug unit from the wall outlet before cleaning. Do not use  
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.  
4. ATTACHMENTS – Do not use attachments not approved by the  
manufacturer as they may result in the risk of fire, electric shock or injury.  
5. WATER AND MOISTURE – Do not use unit near water; for example, near a  
bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a  
swimming pool.  
6. ACCESSORIES – Do not place unit or equipment on an unstable cart, stand  
or table. The unit or equipment may fall, causing serious injury and serious  
damage to the equipment. Wall or shelf mounting should follow the  
manufacturer’s instructions, and should use a mounting kit approved by the  
manufacturer.  
7.  
CARTS – Video equipment and cart combinations should  
be moved with care. Quick stops, excessive force and  
uneven surfaces may cause the equipment and cart  
combination to overturn.  
8. VENTILATION – Slots and openings in the cabinet and the back or bottom  
are provided for ventilation, to ensure reliable operation of the video  
equipment and to protect it from overheating. These openings must not be  
blocked or covered. The openings should never be blocked by placing the  
unit on a bed, sofa, rug or other similar surface. The unit should never be  
placed near or over a radiator or heat register. The unit should not be placed  
in a built-in installation such as a bookcase unless proper ventilation is  
provided.  
9. POWER SOURCES – The unit should be operated only from the type of  
power source indicated on the marking label. If you are not certain of the  
type of power supply you have, consult your video equipment dealer or local  
power company.  
10. GROUNDING OR POLARIZATION – This unit may be equipped with a  
polarized alternating-current line plug (a plug with one blade wider than the  
other). This plug will fit into the power outlet only one way. This is a safety  
feature. If you are unable to insert the plug fully into the outlet, try reversing  
the plug. If the plug still fails to fit, contact your electrician to replace your  
obsolete outlet. Do not defeat the safety purpose of the polarized plug. If  
your unit is equipped with a three-wire grounding-type plug (a plug having a  
third grounding pin), this plug will only fit into a grounding-type power outlet.  
This is a safety feature. If you are unable to insert the plug into the outlet,  
contact your electrician to replace your obsolete outlet. Do not defeat the  
safety purpose of the grounding-type plug.  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
11. POWER CORDS – Do not allow anything to rest on the power cord. Do not  
locate unit or equipment where the cord can be damaged by persons  
walking on it.  
12. HEED WARNINGS – Follow all instructions marked on the unit.  
13. LIGHTNING – During lightning storms or when the unit will be left  
unattended and unused for long periods, unplug the unit and associated  
equipment from the wall outlet. This will prevent damage to the video  
equipment caused by lightning and power-line surges.  
14. OVERLOADING – Do not overload wall outlets and extension cords as this  
can result in a risk of fire or electric shock.  
15. OBJECT AND LIQUID ENTRY – Never push objects of any kind into the  
unit through openings as they may touch dangerous voltage points or short  
out parts that could result in a fire or electric shock. Never spill liquid of any  
kind on the product.  
16. SERVICING – Do not attempt to service the unit as opening or removing  
covers may expose you to dangerous voltage or other hazards. Refer all  
servicing to qualified service personnel.  
17. DAMAGE REQUIRING SERVICE – Unplug the unit and equipment from the  
wall outlet and refer servicing to qualified service personnel under the  
following conditions:  
A.  
B.  
When the power-supply cord or the plug has been damaged.  
If liquid has spilled, or objects have fallen into the unit.  
C. If the unit has been exposed to rain or water.  
D. If the unit does not operate normally when following the operating  
instructions, adjust only those controls that are covered by the  
operating instructions as an improper adjustment of other controls  
may result in damage and will often require extensive work by a  
qualified technician to restore the unit to its normal operation.  
E.  
F.  
If the unit has been dropped or the cabinet damaged.  
When the unit exhibits a distinct change in performance, this indicates  
a need for service.  
18. REPLACEMENT PARTS – When replacement parts are required, be sure  
the service technician uses replacement parts specified by the  
manufacturer or that have the same characteristics as the original part.  
Unauthorized substitutions may result in fire, electric shock or other  
hazards.  
19. SAFETY CHECK – Upon completion of any service or repairs to the unit,  
ask the service technician to perform safety checks to determine that the  
video product is in proper operating condition.  
20. FIELD INSTALLATION – Installation should be performed by a qualified  
service person and should conform to all local codes.  
vi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC COMPLIANCE STATEMENT  
FCC INFORMATION : THIS EQUIPMENT HAS BEEN TESTEDAND FOUND TO  
COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART  
15 OF THE FCC RULES. THESE LIMITSARE DESIGNED TO PROVIDE REASONABLE  
PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS  
OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES,  
USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED  
AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE  
HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS  
EQUIPMENT IN  
A
RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL  
INTERFERENCE IN WHICH CASE THE USER WILLBE REQUIRED TO CORRECTTHE  
INTERFERENCE AT HIS OWN EXPENSE.  
CAUTION : CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY  
THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S  
AUTHORITY TO OPERATE THE EQUIPMENT.  
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.  
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME  
NMB-003 DU CANADA.  
CE COMPLIANCE STATEMENT  
WARNING : THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT  
THIS PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER  
MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.  
vii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table Of Contents Pages  
Chapter 1 Introduction  
Features  
1
1
3
Technical Overview  
Chapter 2 Installation  
Required Tools  
5
5
Connecting Cameras  
Connecting Monitors  
Connecting VCRs  
5
6
6
Connection a Mouse  
Daisy-Chaining and Remote Control Connections  
Alarms and Other Connections  
Initial Setup  
7
7
8
8
Accessing the Main Menu  
Main Menu Settings  
8
10  
11  
13  
14  
15  
16  
18  
19  
20  
22  
23  
24  
25  
27  
29  
30  
31  
32  
Time, Date Setup  
Camera Access Setup  
Camera Title Setup  
Camera Sequence Setup  
Alarm Setup  
Alarm I/O Setup  
Alarm Action Setup (1)  
Alarm Action Setup (2)  
Associated Camera Setup  
Motion Action Setup (1)  
Motion Action Setup (2)  
Video Loss Action Setup  
Manual Alarm Action Setup (1)  
Manual Alarm Action Setup (2)  
Macro Link Setup  
Alarm History  
Motion Detection Setup  
viii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Detection Index Setup  
Motion Detection Index List  
Motion Detection Schedule Setup  
Motion Detection Sensor Setup  
Motion Detection Sensor Setup (Normal)  
Testing Motion Detection Sensor Setup  
Motion Detection Sensor Setup (Vector)  
Playback & Recording Setup  
VCR System Setup  
33  
34  
35  
36  
38  
39  
40  
40  
41  
42  
43  
45  
46  
47  
48  
50  
51  
Recording Index Setup  
Camera Picture Adjustment  
Macro Setup  
Macro Record Setup  
Macro Schedule Setup  
Unit Setup  
Password Setup  
Assigning Passwords  
Chapter 3 Operation  
Buttons and Their Functions  
Menu Operation  
Top Menu  
53  
53  
56  
56  
56  
57  
58  
59  
60  
61  
62  
62  
62  
63  
63  
63  
64  
Bottom Menu  
Live Screen  
Pop Up Menu  
Live Camera Change  
VCR Camera Change  
Zoom  
Full  
Priority On  
Histogram Equalizer  
Panic Record On  
Freeze On  
Sequence  
Utilities  
ix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User Scrn Chg…  
OSD Change…  
Screen Protect…  
Manual Alarm…  
Alarm Reset  
64  
66  
67  
67  
67  
68  
68  
68  
69  
70  
70  
Spot Output…  
Macro  
User Change…  
Alarm List…  
Playback Format…  
PB Picture Adjust…  
Appendix A Troubleshooting  
71  
72  
Appendix B Connector Pin Outs  
Appendix C Remote Control  
Remote Control for Daisychained Multiplexers  
Remote Command Set  
74  
74  
75  
76  
Functional remote commands  
Appendix D Specifications  
Operating Defaults  
Factory Defaults  
77  
77  
77  
80  
80  
80  
80  
81  
81  
81  
81  
82  
82  
82  
Video Format  
Video Level  
Main Output Display Formats (live and playback)  
Resolution (pixels x lines)  
Sampling Standard  
Video Memory  
Refresh Rate (fields/sec.)  
Display Options  
Motion Detection  
VCR Playback  
Alarm Operation  
x
Download from Www.Somanuals.com. All Manuals Search And Download.  
On-Screen Display (Main)  
On-Screen Display (Spot)  
Other Features (Internal)  
Other Features (External Interface)  
Remote Control  
83  
83  
83  
84  
84  
84  
85  
85  
85  
86  
86  
86  
Rear Panel Connectors  
Front Panel Controls  
Power Requirements  
Power Adapter  
Dimensions  
Weight  
Operating Environment  
xi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Illustraions  
Figure 1 — Typical multiplexer system configuration  
Figure 2 — multiplexer connections  
1
5
Figure 3 — Connecting one VCR to the multiplexer  
Figure 4 — Connecting two VCRs to the multiplexer  
Figure 5 — Top menu bar  
6
7
8
Figure 6 — Supervisor Password screen  
9
Figure 7 — Main Menu screen  
10  
10  
12  
13  
14  
15  
16  
18  
19  
20  
22  
23  
24  
25  
27  
29  
30  
31  
32  
33  
34  
35  
36  
38  
39  
40  
Figure 8 — Time, Date Setup, first screen  
Figure 9 — Time, Date Setup, second screen  
Figure 10 — Camera Access Setup screen  
Figure 11 — Camera Title Setup screen  
Figure 12 — Camera Sequence Setup screen  
Figure 13 — Alarm Setup screen  
Figure 14 — Alarm I/O Setup screen  
Figure 15 — Alarm Action Setup (1) screen  
Figure 16 — Alarm Action Setup (2) screen  
Figure 17 — Associated Camera Setup submenu  
Figure 18 — Motion Action Setup (1) screen  
Figure 19 — Motion Action Setup (2) screen  
Figure 20 — Video Loss Action Setup screen  
Figure 21 — Manual Alarm Action Setup (1) screen  
Figure 22 — Manual Alarm Action Setup (2) screen  
Figure 23 — Macro Link Setup screen  
Figure 24 — Alarm History List screen  
Figure 25 — Motion Detection Setup screen  
Figure 26 — Motion Detection Index Setup screen  
Figure 27 — Motion Detection Index List screen  
Figure 28 — Motion Detection Schedule Setup schedule  
Figure 29 — Motion Detection Sensor Setup screen  
Figure 30 — Motion Detection Sensor Setup (Normal) screen  
Figure 31 — Motion Detection Sensor Setup test screen  
Figure 32 — Playback & Recording Setup screen  
xii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 33 — VCR System Setup screen  
Figure 34 — Recording Index Setup screen  
Figure 35 — Camera Picture Adjustment screen  
Figure 36 — Macro Setup screen  
Figure 37 — Macro Recor Setup screen  
Figure 38 — Live screen with M01 REC on the screen  
Figure 39 — Macro Schedule Setup screen  
Figure 40 — Unit Setup screen  
41  
42  
43  
45  
46  
47  
47  
48  
50  
51  
53  
56  
56  
57  
58  
59  
60  
61  
62  
63  
64  
64  
65  
66  
68  
68  
69  
70  
72  
73  
Figure 41 — Passwords Setup screen  
Figure 42 — Password entry screen  
Figure 43 — Front Panel  
Figure 44 — Top Menu  
Figure 45 — Bottom Menu  
Figure 46 — 3x3 Live Screen  
Figure 47 — Pop Up menu  
Figure 48 — Live Cam Change menu  
Figure 49 — VCR Cam Change menu  
Figure 50 — Zoom Screen  
Figure 51 — Histogram Equalizer menu bar  
Figure 52 — Sequence menu  
Figure 53 — Utilities Pop Up menu  
Figure 54 — User Screen Change menu bar  
Figure 55 — Select a Screen menu  
Figure 56 — OSD Setup screen  
Figure 57 — Spot output change screen  
Figure 58 — User Change menu  
Figure 59 — Alarm History List  
Figure 60 — Select Format menu  
Figure 61 — Connetor Sub-Board  
Figure 62 — RS-485 Connector  
Table 1 — Re-Address Commands  
Table 2 — Front key emulation commands  
Table 3 — Remote commands  
74  
75  
76  
xiii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xiv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1  
Introduction  
< Figure 1 > Typical multiplexer system configuration.  
Features  
•
Compatible with standard Black&White cameras and other standard  
Video sources  
•
•
•
Switchable between EIA and CCIR  
Able to decode tapes from many other brands of multiplexers  
Many user-selectable display formats, Cameras can be assigned to  
any display format  
•
•
•
•
Multiple monitor outputs (1 Main, 4 Auxiliary) allow simultaneous  
multi-camera and full-screen viewing  
Multilingual setup menus include English, French, Italian, German,  
Polish and Spanish  
On-screen display includes date, time, alarm status, video loss,  
camera number and 24-character camera titles  
Programmable day and night motion-detection schedules  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
•
Each camera has a programmable 256-target (16 x 16) motion-  
detection grid  
•
•
Programmable vector-based motion detection in any direction  
Nonvolatile program memory saves all user settings and protects  
them against power outages  
•
•
One TTL/CMOS contact closure alarm for each camera  
Up to 4 cameras can be associated with a single contact closure  
alarm  
•
•
Alarm input polarity is user selectable  
VCR switch pulse input for synchronization with VCRs having switch  
pulse feature  
•
Full triplex operation allows simultaneous recording, playback and live  
viewing  
•
•
256-event alarm history log  
Linear Zoom in and out up to 32 times  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Overview  
9 Camera Multiplexing with Motion Detection, Alarm Association and  
Multilingual Setup Menus  
The multiplexer has revolutionary features not available in most  
multiplexers. The multiplexer has a sophisticated motion detection  
system that can sense motion vectors in any direction. Motion detection  
sensitivity can be adjusted and the user can set day and night motion  
detection schedules. A motion tracking box gives visual indications for  
easy setup.  
The multiplexer has composite BNC input and output for VCR. The  
main monitor can be connected to either a composite BNC. There are  
four BNC auxiliary outputs that can be used for “spot” monitors or as  
sources of video for other devices.  
The multiplexer has a large selection of user selectable display formats.  
It also has digital zooming from 1 to 32 times.  
The multiplexer multilingual menu options allow for easy setup. The  
user’s configuration is stored in nonvolatile memory so that it will not be  
lost during power outages.  
The multiplexer can play back videotapes recorded with many other  
multiplexers. These include, but are not limited to; Dedicated Micros,  
ULTRAK Legacy Color, ULTRAK Legacy B/W, Robot, Kalatel and Pelco.  
Up to 9 multiplexers can be “daisy chained” and addressed and  
controlled by a single control panel. The multiplexer can also be  
addressed by a computer using either an RS-232 or RS-485 connection.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2  
Installation  
Required Tools  
Although no special tools are required to install the multiplexer, it is only  
one part of a complex system. Refer to the Installation manuals for the  
other components in your particular installation for special tool  
requirements.  
Up to 9  
Cameras  
Up to 9  
Sensors or  
Contacts  
< Figure 2 > multiplexer connections.  
Connecting Cameras  
You can connect up to 9 cameras to the multiplexer. Connect the  
camera BNCs to the IN BNC connectors (top row). The loop-through  
connectors (OUT) are auto-terminated, so terminating resisters are not  
needed if you do not loop video out to another device.  
NOTE : Connecting a cable to the loop-through connector switches off  
the termination. Do NOT connect a cable to the loop-through BNC  
connectors unless it is connected to the input of another video device.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Monitors  
Your main monitor should be connected to the MAIN output.  
Up to four auxiliary monitors can be connected to the multiplexer. You  
can use these as spot monitors or to view live video while playing tapes  
back through the main monitor. The auxiliary monitors should be  
connected to the AUX BNC connectors.  
Connecting VCRs  
There are BNC connectors for the VCRs.  
< Figure 3 > Connecting one VCR to the multiplexer.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
< Figure 4 > Connecting two VCRs to the multiplexer.  
You can connect one VCR to the multiplexer and use it for both  
recording and playback. However, the multiplexer can handle recording  
and playback at the same time, so it is possible to connect two VCRs.  
One VCR is used to record while the other is used to play back. (See  
the illustrations.)  
Connecting a Mouse  
The multiplexer menus can be controlled by either buttons on the front  
panel or by a mouse. If you plan to use a mouse, connect it to the mini-  
DIN connector labeled MOUSE.  
The multiplexer is not compatible with all mouse available in the market.  
Please note that users are recommended to use "Recommended  
mouse" only described in the manual.  
Logitech mouse (Ball mouse only)  
NOTE : Compatible mouse can be added without prior notice for better  
performance.  
Daisy- Chaining and Remote Control Connections  
The multiplexer can be daisy-chained to other multiplexers or controlled  
by a remote keyboard. To add another multiplexer to your system,  
connect the RS-485 OUT connector of the additional unit to the IN RS-  
485 connector. (See Setup Menu section to set multiplexer address.)  
The remote keyboard should be connected to the OUT connector on the  
multiplexer.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Alarms and Other Connections  
The 50-pin ALARM IN/OUT connector has 9 alarm inputs, 9 alarm  
outputs, RS-232 connectors, VCR trigger pulse and various alarm  
settings. See Appendix B — Connector Pin Outs for further details on  
how to make these connections.  
Initial Setup  
Setting up for EIA or CCIR Operation  
NOTE : When changing the multiplexer to EIA or CCIR all other settings  
are returned to the factory defaults.  
The multiplexer can be used with either EIA or CCIR systems.  
To set it up for EIA operation:  
1) Turn off the power  
2) Press and hold the  
3) Turn on the power  
and {M} buttons.  
To set up the multiplexer for CCIR operation:  
1) Turn off the power  
2) Press and hold the  
3) Turn on the power  
and  
buttons.  
Accessing the Main Menu  
NOTE : To access the Main Menu you must have a Supervisor  
Password. The last item of the Main Menu is the Password Setup.  
Keep the passwords you create in a safe place. The new passwords will  
be the only way to access certain features of the multiplexer once you  
have changed from the factory default passwords.  
< Figure 5 > Top menu bar.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
To access the Main Menu of the setup screens, move the cursor to the  
top of the screen. The top menu bar appears. Select Setup.  
< Figure 6 > Supervisor Password screen.  
Enter the password by moving the cursor over the desired number and  
clicking on it. As you enter each digit, the circles beside “Supervisor  
Password” fill in and move to the right. Once you have entered all four  
digits, click on OK. If you have entered the correct four-digit number, the  
Main Menu will appear. If you have entered an incorrect number,  
Incorrect Password displays for ten seconds and then the unit returns to  
a live display.  
The factory default passwords are listed in the Technical Specifications.  
Click on Cancel to exit the Supervisor Password screen and return to live  
display.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Menu Settings  
< Figure 7 > Main Menu screen.  
< Figure 8 > Time, Date Setup, first screen.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Time, Date Setup  
In addition to setting the multiplexer’s time and date, these screens can  
be used to set the format and select daylight saving time. You can use  
the arrow buttons on the multiplexer or mouse to select the menu item.  
Press SET or the left mouse button to decrease the number. Press ESC  
or the right mouse button to increase the number.  
• Date format : There are three date formats to choose from. The  
month and days are each two-digit numbers represented by MM and  
DD. Years are four-digit numbers represented by YYYY. The U.S.  
format is: MM-DD-YYYY. Europe’s format is: DD-MM-YYYY. Asia’s  
format is: YYYY-MM-DD.  
• Hour format : There are two hour formats to choose from. One is 24-  
hour (military) time. The second is AM/PM.  
• Clock Source : There are two choices for the clock source. If your  
multiplexer is connected to a network, set the option to Network Clock  
and the unit will receive the clock information from the master  
multiplexer. If your multiplexer is not connected to a network, set the  
option to Internal Clock.  
• Year : Use the arrow or mouse buttons to change the year.  
• Month : Use the arrow or mouse buttons to change the month.  
• Date : Use the arrow or mouse buttons to change the date.  
• Hour : Use the arrow or mouse buttons to change the hour.  
• Minute : Use the arrow or mouse buttons to change the minute.  
• Second : Use the arrow or mouse buttons to change the second.  
• Next > : Selecting this takes you to the second Daylight Saving  
setup Screen.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
< Figure 9 > Time, Date Setup, second screen.  
• Daylight Saving : If you are in an area that does not have Daylight  
Saving (Summer) Time, set this option to Off. When you set this  
selection to On, you must set the start and stop dates and times.  
• Start : Set the Month and Date that your area begins Daylight Saving  
time. Unless there is an unusual situation, you will not need to set  
From and To times.  
• Stop : Set the Month and Date that your area ends Daylight Saving  
time. Unless there is there is an unusual situation, you will not need to  
set From and To times.  
• < Back : Selecting this takes you back to the first Time, Date Setup  
Screen.  
• Exit : Selecting this saves your settings and exits the Time, Date  
Setup screens.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camera Access Setup  
< Figure 10 > Camera Access Setup screen.  
The Camera Access Setup screen allows you to assign which cameras  
different users will have access to and which cameras can be displayed  
on the Spot (auxiliary) monitors. You can also designate whether a  
camera can be recorded.  
•
•
•
•
•
•
•
<< : Goes to Camera 1  
< : Goes back one camera  
> : Goes forward one camera.  
>> : Goes to Camera 9  
: An  
next to an item activates the camera for that output.  
O : An O deactivates the camera.  
Exit : Saves your changes and returns to the Main Menu.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camera Title Setup  
< Figure 11 > Camera Title Setup screen.  
The Camera Title Setup screen allows you to enter titles for each  
camera. Clicking on the letters and characters enters them in the  
camera title. Each camera title can have a maximum of 24 characters.  
• Top < : Moves the cursor left.  
• Top > : Moves the cursor right.  
• Middle << : Goes to Camera 1.  
• Middle < : Goes back one camera.  
• Middle > : Goes forward one camera.  
• Middle >> : Goes to Camera 9.  
• Bottom < : Changes the keyboard characters to the previous set.  
• Bottom > : Changes the keyboard characters to the next set.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Keyboard Character Set 1 : A to Z (upper case)  
• Keyboard Character Set 2 : a to z (lower case)  
• Keyboard Character Set 3 : BLANK ! " # $ % & ' ( ) * +, - . / 0 to 9  
• Keyboard Character Set 4 : : ; < = > ? [ \ ] ^ _ ' { I } ~  
• Keyboard Character Set 5 : À Á Â Ä Ç È É Ê Ë Ì Í Î Ï Ñ Ò Ó Ô Ö Ù Ú  
Û Ü ß à á â  
• Keyboard Character Set 6 : ä ç è é ê ë ì í î ï ñ ò ó ô ö ù ú û ü  
• Exit : Saves your changes and returns to the Main Menu.  
Camera Sequence Setup  
< Figure 12 > Camera Sequence Setup screen.  
This screen allows you to set the order in which the cameras appear  
when the multiplexer is in sequence mode. You can also set the how  
long each camera will display from Off to 99 seconds.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enter the camera number under the Camera column and the display  
time under Dwell. You can also set the Stack Dwell Time, which is the  
length of time each group of cameras will display.  
• Exit : Saves your changes and returns to the Main Menu.  
Alarm Setup  
< Figure 13 > Alarm Setup screen.  
The Alarm Setup screen allows you to enter six alarm submenus.  
• Alarm Reset Button : Setting this to On allows users to clear alarm  
events using the front panel buttons or the Pop Up menu. Setting it to  
Off requires the user to enter the Setup Menus to clear alarm events.  
• Alarm Screen Format : This sets the display mode the multiplexer  
will use when an alarm occurs. There are four possible settings: Full,  
2x2, 2x2 Associated and Unchanged.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Alarm Dwell Time : The dwell time can be set from 1 to 99 seconds.  
(The screen will automatically sequence in a multi-alarm condition.)  
• Alarm I/O Setup : Enters the Alarm I/O Setup submenu.  
• Alarm Action Setup : Enters the Alarm Action Setup submenu.  
• Motion Action Setup : Enters the Motion Action Setup submenu.  
• Video Loss Action Setup : Enters the Video Loss Action submenu.  
• Manual Alarm Action Setup : Enters the Manual Alarm Action Setup  
submenu.  
• Macro Link Setup : Enters the Macro Link Setup submenu.  
• Exit : Saves your changes and returns to the Main Menu.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Alarm I/O Setup  
< Figure 14 > Alarm I/O Setup screen.  
You can set the input and output for each of the alarm connections.  
•
In : Can be set to NO (Normally Open), NC (Normally Closed) or  
Off.  
•
•
Out : Can be set to AH (Active High) or AL (Active Low) TTL output.  
Exit : Saves your changes and returns to the Main Menu.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Alarm Action Setup (1)  
< Figure 15 > Alarm Action Setup (1) screen.  
This screen allows you to set up the actions the multiplexer will take  
when there is an alarm condition.  
• Buzzer : When set to On, the multiplexer’s internal buzzer will sound  
during an alarm condition.  
• Alarm Screen : When set to On, the screen display will change to the  
one defined in the Alarm Screen Format menu during an alarm  
condition.  
• Network Relay : When set to On, the multiplexer sends the alarm  
information to an external relay box via the network during an alarm  
condition.  
• Message Latch : When set to On, an “A” displays on the screen when  
an alarm condition occurs. It remains on the screen until it is cleared.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Recording : This allows you to select how video will record during an  
alarm condition. INT interleaves images from the camera with an  
alarm every other field giving you more images from that camera.  
When there are multiple alarms, the cameras with alarms are  
interleaved.  
ONLY records images from only the camera with an alarm condition.  
UNC leaves the recording parameters unchanged.  
• Spot Monitor 1 to 4 : When set to On, that Spot Monitor will display  
the camera with an alarm condition. When there are multiple alarms,  
cameras with alarms will display sequentially. When set to Off, that  
Spot Monitor’s display does not change during alarm conditions.  
• Hold Time : This allows the user to set the alarm actions to last from  
1 to 99 seconds. Hold Time is applicable only if the alarm action is set  
to Timed OUT.  
• Next > : This takes you to the Alarm Action Setup (2) submenu.  
• Exit : Saves your changes and returns to the Main Menu.  
Alarm Action Setup (2)  
< Figure 16 > Alarm Action Setup (2) screen.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This screen allows you to set the actions the operator can take, what  
relays will be activated and what cameras are associated with other  
cameras.  
• Action : There are three possible settings. Timed: The alarm will  
“time out” at the designated time (Hold Time) unless the operator  
clears it earlier. Latched: The alarm remains active until the operator  
acknowledges it. Trans (Transparent): The alarms are not latched and  
cannot be cleared by the operator.  
• Relay : There are four possible relay settings. 1 or 2: Sets either  
internal relay 1 or 2 to be activated by an alarm. 1&2: Sets both  
internal relays 1 and 2 to be activated by an alarm. Off: Neither  
internal relay will be activated by an alarm.  
• Associated : This button allows you to associate other cameras with  
a camera that is in an alarm condition. Selecting this item will take  
you to the Associated Camera Setup submenu.  
• < Back : This takes you to the Alarm Action Setup (1) submenu.  
• Exit : Saves your changes and returns to the Main Menu.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Associated Camera Setup  
< Figure 17 > Associated Camera Setup submenu.  
This menu allows you to associate up to three cameras with another  
when an alarm condition occurs. The main camera is displayed in the  
top window with the three associated cameras shown below. Under  
each of the associated camera windows is a control bar.  
• < : Goes through the cameras in reverse order.  
• On/Off : By setting this to On, the selected camera will be associated  
with the camera with the alarm condition. (If all three Associated  
Cameras are set to Off, no cameras will be associated to the camera  
with that camera.)  
• > : Goes through the cameras in forward order.  
• Exit : Saves your changes and returns to the previous menu.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Action Setup (1)  
< Figure 18 > Motion Action Setup (1) screen.  
This screen allows you to set up the actions the multiplexer will take  
when there is a motion alarm condition.  
•
Buzzer : When set to On, the multiplexer’s internal buzzer will sound  
during a motion alarm condition.  
•
Alarm Screen : When set to On, the screen display will change to the  
one defined in the Alarm Screen Format menu during a motion alarm  
condition.  
•
•
Network Relay : When set to On, the multiplexer sends the alarm  
information to an external relay box via the network during a motion  
alarm condition.  
Message Latch : When set to On, an “M” displays on the screen  
when a motion alarm condition occurs. It remains on the screen until  
it is cleared.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Recording : This allows you to select how video will record during a  
motion alarm condition. INT interleaves images from the camera with  
an alarm every other field giving you more images from that camera.  
When there are multiple alarms, the cameras with alarms are  
interleaved. ONLY records images from only the camera with an  
alarm condition. UNC leaves the recording parameters unchanged.  
• Spot Monitor 1 to 4 : When set to On, that Spot Monitor will display  
the camera with a motion alarm condition. When there are multiple  
alarms, cameras with alarms will display sequentially. When set to Off,  
that Spot Monitor’s display does not change during motion alarm  
conditions.  
• Next > : This takes you to the Motion Alarm Action Setup (2)  
submenu.  
• Exit : Saves your changes and returns to the Main Menu.  
Motion Action Setup (2)  
< Figure 19 > Motion Action Setup (2) screen.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This screen allows you to associate various relays and links to the  
cameras in motion alarm conditions.  
• Relay : There are four possible relay settings. 1 or 2: Sets either  
internal relay 1 or 2 to be activated by a motion alarm. 1&2: Sets both  
internal relays 1 and 2 to be activated by a motion alarm. Off: Neither  
internal relay will be activated by a motion alarm.  
• Alarm Link : This button links the motion detection to an alarm action.  
It can be set to Off or any one of the 9 alarm actions. All alarm  
actions take priority over motion actions.  
• < Back : This takes you to the Motion Alarm Action Setup (1)  
submenu.  
• Exit : Saves your changes and returns to the Main Menu.  
Video Loss Action Setup  
< Figure 20 > Video Loss Action Setup screen.  
This screen allows you to set up the actions the multiplexer will take  
when there is a video loss condition.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Buzzer : When set to On, the multiplexer’s internal buzzer will sound  
during a video loss condition.  
• Alarm Screen : When set to On, the screen display will change to the  
one defined in the Alarm Screen Format menu during a video loss  
condition.  
• Internal Relay : Selects which internal relays will be activated during  
a video loss condition. 1 or 2 activates the designated relay. 1&2  
activates both internal relays. Off means neither relay will activate.  
• Network Relay : When set to On, the multiplexer sends the video loss  
information to an external relay box via the network during a video  
loss condition.  
• Message Latch : When set to On, a “V” displays on the screen when  
a video loss condition occurs. It remains on the screen until it is  
cleared.  
• Spot Monitor 1 to 4 : When set to On, that Spot Monitor will display  
the camera with a video loss condition. When there are multiple  
alarms, cameras with alarms will display sequentially. When set to  
Off, that Spot Monitor’s display does not change during video loss  
conditions.  
• Hold Time : This allows the user to set the actions to last from 1 to 99  
seconds.  
• Exit : Saves your changes and returns to the previous menu.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manual Alarm Action Setup (1)  
< Figure 21 > Manual Alarm Action Setup (1) screen.  
This screen allows you to set up the actions the multiplexer will take  
when there is a Manual alarm condition.  
• Buzzer : When set to On, the multiplexer’s internal buzzer will sound  
during a Manual alarm condition.  
• Alarm Screen : When set to On, the screen display will change to the  
one defined in the Alarm Screen Format menu during a Manual alarm  
condition.  
• Network Relay : When set to On, the multiplexer sends the alarm  
information to an external relay box via the network during a Manual  
alarm condition.  
• Message Latch : When set to On, an “A” displays on the screen when  
a Manual alarm condition occurs. It remains on the screen until it is  
cleared.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Recording : This allows you to select how video will record during a  
Manual alarm condition. INT interleaves images from camera with an  
alarm every other field giving you more images from that camera.  
When there are multiple alarms, the cameras with alarms are  
interleaved. ONLY records images from only the camera with an  
alarm condition. UNC leaves the recording parameters unchanged.  
• Spot Monitor 1 to 4 : When set to On, that Spot Monitor will display  
the camera with a Manual alarm condition. When there are multiple  
alarms, cameras with alarms will display sequentially. When set to  
Off, that Spot Monitor’s display does not change during Manual alarm  
conditions.  
• Hold Time : This allows the user to set the alarm actions to last from  
1 to 99 seconds. Hold Time is applicable only if the alarm action is set  
to Timed OUT.  
• Next > : This takes you to the Manual Alarm Action Setup (2)  
submenu.  
• Exit : Saves your changes and returns to the previous menu.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manual Alarm Action Setup (2)  
< Figure 22 > Manual Alarm Action Setup (2) screen.  
This screen allows you to set the actions the operator can take, what  
relays will be activated and what cameras are associated with other  
cameras.  
• Action : There are three possible settings. Timed: The alarm will  
“time out” at the designated time (Hold Time) unless the operator  
clears it earlier.  
Latched : The alarm remains active until the operator acknowledges  
it. Trans (Transparent): The alarms are not latched and cannot be  
cleared by the operator.  
• Relay : There are four possible relay settings. 1 or 2: Sets either  
internal relay 1 or 2 to be activated by an alarm. 1&2: Sets both  
internal relays 1 and 2 to be activated by an alarm. Off: Neither  
internal relay will be activated by an alarm.  
• Alarm Link : This selects whether the alarm action will be linked or  
not. It can be set to Off or any of the 9 alarm actions. All alarm  
actions take priority over manual alarm actions.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• <Back : This takes you to the Manual Alarm Action Setup (1)  
submenu.  
• Exit : Saves your changes and returns to the previous menu.  
Macro Link Setup  
< Figure 23 > Macro Link Setup screen.  
This screen allows you to link macros to the 9 alarms. Each alarm can  
be set to Off or linked to any of 9 macros.  
•
Exit : Saves your changes and returns to the previous menu.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Alarm History  
< Figure 24 > Alarm History List screen.  
This screen displays a list of alarms. The multiplexer retains a history of  
up to 256 events.  
• << : Goes to the first page in the history list.  
• < : Goes back one page in the history list.  
• > : Goes forward one page in the history list.  
• >> : Goes to the last page in the history list. (maximum 16 pages)  
• Clear : This clears all the information from the history list. You will be  
asked to confirm that you really want to delete all the alarm history  
information before it is deleted.  
• Print : Transmits all alarm history list to PC.  
NOTE : Before implement "Print" function, make sure follow the below  
steps.  
1. Go to the vender's website.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Download the "Download.exe" file on your PC.  
3. Implement the "Download.exe" file and click the icon named  
"Print Program".  
4. Now user's are ready to use "Print" function.  
•
Exit : Saves your changes and returns to the Main Menu.  
Motion Detection Setup  
< Figure 25 > Motion Detection Setup screen.  
The Motion Detection Setup screen is the starting point for various  
motion detection setup screens.  
• All Motion Detection: This is a global switch that turns motion  
detection for all cameras On or Off.  
• Motion Detection Index Setup: Takes you to that submenu.  
• Motion Detection Schedule Setup: Takes you to that submenu.  
• Motion Detection Sensor Setup: Takes you to that submenu.  
• Exit: Saves your changes and returns to the Main Menu.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Detection Index Setup  
< Figure 26 > Motion Detection Index Setup screen.  
Normally, the multiplexer gives equal priority to all cameras (1 to 9) for  
motion detection. However, it is possible to change the priorities.  
• + : Increases the camera number by one.  
• - : Decreases the camera number by one.  
• < : Scrolls through the camera array to the left.  
• > : Scrolls through the camera array to the right.  
• Delete : Deletes the highlighted camera from the array.  
• Insert : Inserts a blank into the array.  
• End : Enters an “E” which sets the end mark for the index list.  
• View : Displays the Motion Detection Index List.  
• Exit : Saves your changes and returns to the previous menu.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Detection Index List  
< Figure 27 > Motion Detection Index List screen.  
This screen displays the priorities assigned to the cameras. You cannot  
edit anything on this screen.  
• Exit : Returns to the previous menu.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Detection Schedule Setup  
< Figure 28 > Motion Detection Schedule Setup schedule.  
The multiplexer can be set up to detect or ignore motion based on a  
schedule. For example, you would expect lots of activity during normal  
office hours and do not want to detect motion. However, when the office  
is closed, motion should generate an alarm condition.  
• Timer 1 & 2 : Each timer can be turned On or Off, and they can be set  
to Mode 1 or 2. (Modes 1 and 2 are defined in the Motion Detection  
Sensor Setup screen.)  
• Start & Stop : You can set the start and stop time for each timer. A  
start time of 18:00 with an end time of 06:00 will go from 6:00 p.m.  
until 6:00 a.m. of the following morning.  
• Days : The timers can be turned On or Off for each day of the week.  
= On and O = Off.  
• Exit : Saves your changes and returns to the previous menu.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Detection Sensor Setup  
< Figure 29 > Motion Detection Sensor Setup screen.  
Each camera can be set up with two sets of motion detection  
parameters. The parameter sets are defined as Mode 1 and Mode 2.  
(You can schedule when the modes will be used in the Motion Detection  
Schedule Setup screen.)  
• On/Off : Turns motion detection On or Off.  
• Update/Master : When using Update, the multiplexer compares the  
current field with the previous one. When using Master, the  
multiplexer compares a master image to continuous video.  
• Normal/Vector : When set to Normal, the multiplexer detects all  
motion. When set to Vector, the multiplexer detects motion based on  
user definitions.  
• Sensitivity : Sets how much luminance change there must be in the  
target area before the multiplexer reads the change as motion. 01 is  
the lowest sensitivity and 16 is the highest.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Trigger Size (H) : This is the minimum number of targets in a  
horizontal row that must change before the multiplexer reads the  
change as motion. The range is 01 to 16.  
• Trigger Size (V) : This is the minimum number of targets in a vertical  
row that must change before the multiplexer reads the change as  
motion. The range is 01 to 16.  
• Delay Time : The delay time is used to make adjustments for scenes  
that have sudden changes such as lights and shadows created by  
headlights of nearby traffic. The delay can be set from 0 to 5 seconds.  
• Hold Time : The Hold Time can be set from 1 to 99 seconds.  
• Grid Setup : Takes you to the Motion Detection Sensor Setup screen.  
• << : Goes to Camera 1.  
• < : Goes back one camera.  
• > : Goes forward one camera.  
• >> : Goes to Camera 9.  
• Reset : Returns all settings to the motion detection sensor setup  
default.  
• Exit : Saves your changes and returns to the previous menu.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Detection Sensor Setup (Normal)  
< Figure 30 > Motion Detection Sensor Setup (Normal) screen.  
The Motion Detection Sensor Setup screen is used to setup and test  
cameras for motion detection. Mode 1 and Mode 2 can be set up for  
either Normal or Vector motion detection. The following describes  
Normal motion detection.  
• SET : Highlights the grids area.  
Click of the mouse on this icon has no action.  
• Dot/Line/All : Determines how many targets will be turned on or off.  
Dot = single target. Line = a row of targets. All = all the targets.  
• Reverse : Set all targets to the reverse side.  
• Test : Goes to the Motion Detection Sensor Setup test screen.  
• Exit : Saves your changes and returns to the previous menu.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Testing Motion Detection Sensor Setup  
< Figure 31 > Motion Detection Sensor Setup test screen.  
The Motion Detection Sensor Setup test screen shows when the  
multiplexer detects motion by drawing a box around the active area.  
This gives you instant feedback letting you know if you have set the  
correct size and sensitivity for the types of motion you want to detect.  
• Master Screen Set : Saves the master image. (This button only  
appears in the Master Mode.)  
• Exit : Returns to the previous menu.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Detection Sensor Setup (Vector)  
The Vector Motion Detection Sensor Setup screen is the same as the  
Normal Motion Detection Sensor Setup screen except that it has two  
motion grids. To detect left to right motion, you define the first grid and  
then define a second grid to the right of the first.  
•
•
A ON : Used to define the first grid.  
B ON : Used to define the second grid.  
Refer to Motion Detection Sensor Setup (Normal) for descriptions of all  
the other settings.  
Playback & Recording Setup  
< Figure 32 > Playback & Recording Setup screen.  
The Playback & Recording Setup screen gives you access to submenus  
for setting up playback and recording.  
• VCR System Setup : Opens the submenu.  
• Recording Index Setup : Opens the submenu.  
• Exit : Saves your changes and returns to the Main Menu.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR System Setup  
< Figure 33 > VCR System Setup screen.  
The VCR System Setup screen is used to synchronize the multiplexer  
with your VCR.  
NOTE : If your VCR has a synchronizing trigger pulse, using it will save  
you a lot of time when setting up your system.  
• VCR Input : There is the BNC for multiplexer input from the VCR.  
• External Trigger : Set to Off if you are not using the VCR’s  
synchronizing trigger pulse. When using your VCR’s synchronizing  
trigger pulse, set to match the VCR’s signal; + for positive edge  
sensing and – for negative edge sensing.  
• Panic Rec Buzzer : When On, the buzzer will beep every 20  
seconds.  
• VCR Type : Selecting this brings up a list of VCRs. Select your VCR  
from the list. If your VCR is not on the list select User Define.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
•
Normal & Alarm Record : If you selected a VCR from the list, all you  
need to set is the hours. If you selected User Define, you need to set  
the hours and field delay. Although you can set Normal and Alarm  
hours the same, you usually want higher quality video in an alarm  
situation. For example, you might set Normal to 24-hour time-lapse  
and Alarm to 2-hour mode. You will need to get the field delay rates  
from your VCR manufacturer.  
•
Exit : Saves your changes and returns to the previous menu.  
Recording Index Setup  
< Figure 34 > Recording Index Setup screen.  
Normally, the multiplexer gives the same priority to all cameras.  
However, you can set it up so that cameras are given different recording  
priorities.  
• + : Increases the camera number by one.  
• - : Decreases the camera number by one.  
• < : Scrolls through the camera array to the left.  
• > : Scrolls through the camera array to the right.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Delete : Deletes the highlighted camera from the array.  
• Insert : Inserts a blank into the array.  
• End : Enters an “E” which sets the end mark for the index list.  
• View : Displays the Motion Detection Index List.  
• Exit : Saves your changes and returns to the previous menu.  
Camera Picture Adjustment  
< Figure 35 > Camera Picture Adjustment screen.  
NOTE : Do not make any adjustments with this screen until all of the  
cameras and monitors have been adjusted properly.  
• << : Goes to Camera 1.  
• < : Goes back one camera.  
• > : Goes forward one camera.  
• >> : Goes to Camera 9.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The following adjustments have a default setting of 00. The other values  
are Min = minimum, 127 to -01 = adjustments below default, 01 to 127 =  
adjustments above default, and Max = maximum.  
• Contrast : Adjusts contrast.  
• Brightness : Adjusts brightness.  
• Sharpness : Adjusts sharpness.  
• Exit : Saves your changes and returns to the Main Menu.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Macro Setup  
< Figure 36 > Macro Setup screen.  
The Macro Setup screen lets you access the two macro setup  
submenus.  
•
•
•
Macro Recording Setup : Opens the submenu.  
Macro Schedule Setup : Opens the submenu.  
Exit : Saves your changes and returns to the Main Menu.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Macro Record Setup  
< Figure 37 > Macro Record Setup screen.  
Selecting any of the Record Start buttons takes you to a live screen  
where all of your key strokes or mouse operations except for password  
protected operations will be recorded as a macro.  
•
Exit : Saves your changes and returns to the previous menu.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
< Figure 38 > Live screen with M01 REC on the screen.  
Macro Schedule Setup  
< Figure 39 > Macro Schedule Setup screen.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
You can create up to 20 event schedules that use macros.  
• Event : Scheduled event number; 01 through 20  
• On/Off : Turns the selected event On or Off.  
• Macro : Selects the macro that that event is to perform.  
• Time : Sets the time the event is to be done.  
• Day : Sets the day(s) the event is to be done. = enables the event.  
O = disables the event.  
• Exit : Saves your changes and returns to the previous menu.  
Unit Setup  
< Figure 40 > Unit Setup screen.  
This screen allows you to change the multiplexer basic settings.  
•
Language : There are five languages available: English, French,  
Italian, German, Polish and Spanish.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
•
•
•
Mouse : If you plan to use a mouse to control you multiplexer, set  
this to On.  
Key lock : When On, pressing any key or clicking the mouse will  
open a screen asking for a password.  
Factory Reset : Returns all settings to the factory default.  
A confirmation screen will ask you if you really want to reset  
everything.  
•
•
Cam No. Offset : When set to On, the multiplexer will adjust the  
camera numbers based on the Unit Address. Unit 001 will have  
Cameras 01 to 9, Unit 002 will have Cameras 10 to 18, etc. When  
set to Off, the cameras will be numbered 01 to 9.  
Mouse setup : If the mouse cannot be worked properly, the user can  
change the values as follows.  
The ranges which can be changed are Min=minimum, -009~009 and  
Max=maximum.  
•
•
•
•
•
•
Master/Slave : When installed as part of a network, this will  
determine if the unit is a master or slave unit.  
Network Type : The multiplexer can be set to RS-232, RS-422 or  
RS-485 when connected to a network.  
Baud Rate : When connected to a network, the baud rate can be set  
to 1200, 2400, 4800, 9600 or 19200.  
Unit Address : Networked multiplexers can be assigned addresses  
from 001 to 255.  
Protocol : A is multiplexer protocol.  
B1 is dome camera control protocol.  
Exit : Saves your changes and returns to the Main Menu.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Password Setup  
< Figure 41 > Passwords Setup screen.  
NOTE : Keep a copy of the supervisor password in a safe place. Once  
you have changed the supervisor password from the factory default, you  
will not be able to access protected menus without it.  
The Password Setup screen allows you to assign PIN codes to the  
supervisor and up to four users.  
• Setup Menu Password : When On, only the supervisor can enter  
and make changes in the Setup Menu.  
• User Change Password : When On, a password will be required to  
make screen configuration changes or to access items on the Pop Up  
menu.  
• Supervisor : Opens the Password Entry screen.  
• User 1 to 4 : Opens the Password Entry screen.  
• Exit : Saves your changes and returns to the Main Menu.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assigning Passwords  
< Figure 42 > Passwords entry screen.  
Use the numbers to enter a four-digit PIN.  
• Clear : Deletes all entered numbers, and you can restart entry.  
• OK : Opens the re-enter screen after the first try. Compares the entry  
to the first password, and exits the Setup Menu if they match.  
• Cancel : Cancels the password setup and exits the Setup Menu.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3  
Operation  
< Figure 43 > Front Panel.  
Buttons and Their Functions  
Allows the operator to generate an alarm. When pressed along with  
a camera button, it places that camera in the alarm mode.  
•
•
•
•
OPERATION : Press  
and then a camera button.  
Pressing this button switches the multiplexer into VCR playback  
mode or VCR preview mode.  
OPERATION : Press  
mode. Press 2nd and then  
to switch the multiplexer into VCR playback  
to switch the VCR to preview mode.  
{M} Plays a Macro.  
OPERATION : Press {M} and then a camera button to play macros 1  
to 9.  
REC Puts a camera in the Panic Record Mode.  
OPERATION : Press REC and then a camera button to put that  
camera in the panic record mode.  
Puts the multiplexer in Full-Screen Mode or the first user-defined  
display mode.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
•
OPERATION : Press  
and the currently selected camera displays  
full screen. Pressing another camera button will display that camera  
full screen. Press 2nd and then  
to display a screen layout  
previously defined by the user.  
PIP (Picture in Picture) inserts a selected camera as a small  
image in the main image.  
•
•
OPERATION : Press  
you want displayed in the insert.  
and then the camera button of the camera  
Puts the multiplexer in 2x2 display mode or the second user-  
defined display mode  
OPERATION : Press  
Press 2nd and then  
and four cameras display on the screen.  
to display the second screen layout  
previously defined by the user.  
Puts the multiplexer in PIP4 display mode or the third user-  
defined display mode  
•
OPERATION : Press  
Press 2nd and then  
defined by the user.  
and five cameras display on the screen.  
to display the third screen layout previously  
Puts the multiplexer in 3x3 display mode or the fourth user-  
defined display mode  
•
•
OPERATION : Press  
Press 2nd and then  
defined by the user.  
and nine cameras display on the screen.  
to display the fourth screen layout previously  
Puts the multiplexer in the Sequence Mode.  
OPERATION : Press  
to start or stop all cameras sequencing  
while in the 2x2, 3x3, PIP or User-defined Modes 1 to 4. Press  
while in the Full-Screen Mode to start or stop a User-defined  
sequence.  
Press 2nd,  
and camera buttons 1, 2, 3 or 4 to start or stop Spot  
Sequences 1 to 4 respectively.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Press ESC and  
to start Stack Sequence which sequences  
through multi-format screens.  
2nd In addition to its other functions, the 2nd button can be used to  
assign cameras to the Spot monitors.  
• OPERATION : Press 2nd then 1, 2, 3 or 4 to select the Spot monitor;  
then press camera button of the camera you want displayed on that  
Spot monitor. You can assign any one of the 9 cameras to any of the  
four Spot monitors.  
This button freezes the video.  
• OPERATION : Press  
to freeze the video from the currently  
selected camera. Press ESC then  
to freeze the video from all the  
cameras.  
This button enters the Zoom Mode.  
• OPERATION : Press  
to enter the Zoom Mode.  
SET This button has several functions; it brings up a Popup Menu,  
sets selections on the OSD menus and decreases numbers in the  
number setup function.  
• OPERATION : Press SET to enter the Popup Menu or to set a  
selected item from on of the menus.  
ESC This button has several functions; it acts as a “Cancel” button,  
clears Cameo selections and increases numbers in the number setup  
function.  
• OPERATION : Press ESC to cancel entries, clear the Cameo or to  
decrease the number.  
The Up, Down, Left and Right buttons are used whenever  
you need to move the cursor, highlight bar or Cameo window.  
• OPERATION : Press the arrow corresponding to the direction you  
want to move.  
1 to 9 These buttons are used to make camera selections or enter  
numbers as needed.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operation  
The multiplexer takes advantage of On-Screen Display (OSD) menus.  
You can navigate through these menus using a mouse or the arrow  
buttons. There are two main menus: Top and Bottom. The Top Menu is  
accessed by moving the cursor to the top edge of the screen. The  
Bottom Menu is accessed by moving the cursor to the bottom edge of  
the screen.  
Top Menu  
< Figure 44 > Top Menu  
The Top Menu has five selections.  
• Live : Clicking on Live returns to the last Live mode screen format  
displayed.  
• Playback : Clicking on Playback returns to the last screen format  
accessed in the Playback mode.  
• Preview : Clicking on Preview displays the Preview mode.  
• Setup : Clicking on Setup opens the Setup Menu. This feature is  
password protected. (See Chapter 2 for a description of the Setup  
Menu.)  
• Cancel : Clicking Cancel exit the top menu without any changes.  
Bottom Menu  
< Figure 45 > Bottom Menu  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The bottom menu is only available in the Live Mode. It has ten  
selections.  
• Full : Switches to full screen display of one camera.  
• PIP : Switches to a display with a Picture-in-Picture  
• 2x2 : Switches to four cameras displayed on the screen.  
• PIP4 : Switches to five cameras displayed on the screen.  
• 3x3 : Switches to nine cameras displayed on the screen.  
• User Def1 to 4 : Switch to user defined displays 1 to 4.  
• Cancel : Exits the menu without any changes.  
Live Screen  
< Figure 46 > 3x3 Live Screen.  
When you move the mouse around while in the live screen mode or  
when you press the Up, Down, Left and Right arrow buttons, the boarder  
around the selected camera image will change to white. This indicates  
that camera image is ready for an action.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pop Up Menu  
< Figure 47 > Pop Up Menu  
Clicking the right mouse button or pressing the SET button cause the  
Pop Up menu to appear. There is a list of ten items that can be selected  
from the Pop Up menu.  
•
•
•
•
•
•
•
•
•
•
Live Cam Change… : Allows you to select the “Live” camera.  
Zoom… : Enters the digital zoom mode.  
Full : Displays the selected camera full screen.  
Priority : Toggles between On and Off.  
Histogram : Toggles between On and Off.  
Panic Record : Toggles between On and Off.  
Freeze : Toggles between On and Off.  
Sequence… : Enters the Sequence setup mode.  
Utilities… : Enters the Utilities mode.  
Cancel : Closes the menu.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Live Camera Change  
< Figure 48 > Live Cam Change menu  
The Live Camera Change menu allows you to assign any camera to  
active cameo.  
• 1 to 9 : Selecting these buttons changes the cameo camera.  
• Cancel : Exits the menu without any changes.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Camera Change  
< Figure 49 > VCR Cam Change menu  
This menu will appear on the Pop Up menu only when the unit is  
Playback mode.  
The VCR Camera Change menu allows you to assign any camera to  
active cameo.  
• 1 to 9 : Selecting these buttons changes the cameo camera.  
• Cancel : Exits the menu without any changes.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Zoom  
< Figure 50 > Zoom Screen.  
The digits on the top right of the screen indicate the amount of zoom.  
The maximum zoom is 32 times.  
The picture insert at the bottom right shows the entire seen with a  
rectangle representing the zoomed area.  
• Freeze : Clicking this freezes the image on the screen.  
• In : Zooms in (enlarges).  
• Out : Zooms out.  
• Arrow buttons : The arrow buttons are used to move the zoomed  
area left, right, up and down.  
• Exit : Clicking this button exits the Zoom Mode.  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Full  
Clicking Full on the Pop Up menu causes the active camera to display  
full screen.  
Priority On  
When Priority is set to On for a camera, it will display in real time, and  
the refresh rate of the other cameras will slow down.  
Histogram Equalizer  
< Figure 51 > Histogram Equalizer menu bar.  
• HEQ1 to 4 : Each Histogram Equalizer button increases image  
contrast. HEQ1 has the weakest equalization and HEQ4 has the  
strongest equalization.  
NOTE : Image noise increases as you use stronger equalization. This  
is a property of the equalization algorithm and is does not indicate a  
problem with your system.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• OFF : Cancels any Histogram Equalizer settings and returns the  
image contrast to the original value.  
• Cancel : Cancel exits the menu without any changes.  
Panic Record On  
When Panic Record is selected only the selected camera is recorded,  
and it records in real-time speed.  
Freeze On  
When Freeze is selected, the image is frozen on the screen until you  
reset it.  
Sequence  
< Figure 52 > Sequence menu.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Sequence selection displays the sequence menu.  
• Turn All Cam Seq On : This selection starts sequencing all cameras  
that are not currently displayed on the screen.  
• Turn User Set Seq On : This selection starts a sequence that was  
defined in the Setup Menu.  
• Cancel : Exits the menu without any changes.  
Utilities  
< Figure 53 > Utilities Pop Up menu.  
User Scrn Chg...  
< Figure 54 > User Screen Change menu bar.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This opens the User Screen Change menu.  
This menu allows the user to select one of four displays that were  
defined in the Bottom Menu. After selecting one of the UserDef buttons,  
the Select a Screen menu appears.  
< Figure 55 > Select a Screen menu.  
• << : Jumps back through the first screen formats at a time.  
• < : Scrolls back through the screen formats one at a time.  
• > : Scrolls forward through the screen formats one at a time.  
• >> : Jumps forward through the last screen formats at a time.  
• OK : Confirms the screen format selection.  
• Cancel : Exits the menu without any changes.  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD Change...  
< Figure 56 > OSD Setup screen.  
The OSD Setup screen allows you to select what text will be display and  
what color the text will be.  
• Border Line : The border around the images.  
• Lv Cam Number : The live camera’s number.  
• Pb Cam Number : The playback camera’s number.  
• Lv Cam Title : The live camera’s title.  
• Pb Cam Title : The playback camera’s title.  
• Lv Time Date : The live camera’s time and date.  
• Pb Time Date : The playback camera’s time and date.  
• Vloss Text : When the video signal is lost, a “V” displays on the  
screen.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Alarm Text : When an alarm occurs, an “A” displays on the screen.  
• Motion Text : When motion is detected, an “M” displays on the  
screen.  
• Freeze Text : When an image is frozen, an “F” displays on the  
screen.  
• Sequence Text : When the multiplexer is in sequence mode, an “S”  
displays on the screen.  
• Motion Box : When motion is detected, a box showing the area  
displays on the screen.  
• Active Box : When the camera is selected, the active window box  
Displays.  
• Spot OSD : The Spot OSD time, date and camera number, title.  
• Default Color : Clicking this button resets the color to factory default  
• Exit : Saves your changes and returns to the live screen.  
Screen Protect...  
The Screen Protect feature allows users to protect there setups against  
use or change by unauthorized persons.  
Manual Alarm  
This feature allows the user to trigger an alarm manually.  
Alarm Reset  
This feature allows the user to reset an alarm.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Spot Output...  
< Figure 57 > Spot output change screen.  
This feature allows the user to assign different cameras to the spot  
monitors.  
Macro  
This feature allows the user to select which macro will play.  
User Change...  
< Figure 58 >  
User Change menu.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting Supervisor or one of the user numbers opens a password  
screen allowing that user to log on. The Supervisor has access to all the  
menus and setup features. Users can be assigned different levels of  
access. For example some users might not be able to view certain  
cameras.  
Alarm List...  
< Figure 59 > Alarm History List.  
This screen displays a list of alarms. The multiplexer retains a history of  
up to 256 events.  
• << : Goes to the first page in the history list.  
• < : Goes back one page in the history list.  
• > : Goes forward one page in the history list.  
• >> : Goes to the last page in the history list. (maximum 16 pages)  
• Print : Transmits all alarm history list to PC.  
• Exit : Returns to the previous screen.  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback Format...  
< Figure 60 > Select Format menu..  
Your multiplexer can play back tapes that were recorded using different  
multiplexers. This menu allows you to choose from HONEYWELL,  
ULTRAK Legacy Color, ULTRAK B/W, Dedicated Micros, Robot  
(Sensormatic), Pelco and Kalatel (Impac).  
PB Picture Adjust...  
This option appears on the Pop Up menu aonly when the unit is in the  
Playback Mode. It allows the user to adjust images played back from the  
VCR.  
The following adjustments have a default setting of 00. The other values  
are Min = minimum, -127 to -01 = adjustments below default, 01 to 127 =  
adjustments above default, and Max = maximum.  
• Contrast : Adjusts contrast.  
• Brightness : Adjusts brightness.  
• Sharpness : Adjusts sharpness.  
• Cancel : Closes the menu without any changes.  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix A  
Troubleshooting  
Problem  
Try This  
No Video (black screen)  
No Video (one camera)  
Check power connections  
Check camera power and coaxial cable  
No Video (jumbled colors) Make certain multiplexer is set correctly for  
your system (EIA or CCIR)  
Fuzzy Image (one camera) Check camera focus  
Bad Video (one camera)  
Check the loop through connector.  
If a cable is attached, make certain it is  
connected to another video device on the  
other end.  
Wrong Language  
Buttons Locked  
Change the language in the Setup Menu  
Unlock buttons in Setup Menu.  
Recorded Video Rolls  
Check VCR configuration in Setup Menu.  
Use the trigger pulse from the multiplexer  
for optimum synchronization with a time-  
lapse VCR.  
Tape Plays Only 3x3  
Make certain video cable to the VCR input  
is connected to the VCR OUT of the  
multiplexer.  
Too Many Motion Alarms  
Adjust sensitivity of motion detection grid.  
Adjust size of grid required to activate  
motion alarm. Make certain only the area  
you want to detect motion is activated.  
Motion Not Detected  
Adjust sensitivity of motion detection grid.  
Adjust size of grid required to activate  
motion alarm.  
Make certain the area you want to detect  
motion is activated.  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B  
Connector Pin Outs  
The multiplexer has a 50-pin connector used for alarm input and output,  
RS-232 network connections, VCR trigger pulse, and updating the  
multiplexer’s firmware. A sub-board is supplied to simplify connections.  
See the illustration below for connection details.  
< Figure 61 > Connector Sub-Board  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
< Figure 62 > RS-485 Connector  
NOTE : If termination of RS-485 network is required, short pin 3 and  
pin 4.  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix C  
Remote Control  
Remote Control for Daisychained Multiplexers  
If you are using a computer to control two or more daisy-chained  
multiplexers, you need to send a re-address command to select the  
multiplexer to control. (Up to 16 multiplexers can be daisy-chained.)  
Re-address commands are not printable characters; you need an 8-bit  
binary address or hex value to select which daisy-chained multiplexer  
you control. If you lose power to one or more multiplexers, you will need  
to use the re-address command again to select the correct multiplexer.  
HEX  
RESULTS  
HEX  
RESULTS  
00  
01  
02  
03  
04  
05  
06  
07  
08  
NUL (changes active multiplexer)  
1 (1st connected multiplexer)  
2 (2nd connected multiplexer)  
3 (3rd connected multiplexer)  
4 (4th connected multiplexer)  
5 (5th connected multiplexer)  
6 (6th connected multiplexer)  
7 (7th connected multiplexer)  
8 (8th connected multiplexer)  
09  
9 (9th connected multiplexer)  
0A 10 (10th connected multiplexer)  
0B 11 (11th connected multiplexer)  
0C 12 (12th connected multiplexer)  
0D 13 (13th connected multiplexer)  
0E 14 (14th connected multiplexer)  
0F 15 (15th connected multiplexer)  
10  
16 (16th connected multiplexer)  
< Table 1 > Re-Address Commands  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Command Set  
Simple three-character ASCII commands represent single or  
combination front panel button presses on the multiplexer. The effect of  
a button press or remote command depends on the multiplexer’s current  
status. Check the multiplexer’s current status before issuing a remote  
command. Because this multiplexer has a different front keys from the  
old model, some new commands are added to control the multiplexer  
correctly.  
ASCII  
MULTIPLEXER KEY  
ASCII  
MULTIPLEXER KEY  
/PA  
/TP  
/MA  
/SX  
/FZ  
/PP  
/22  
PALARM  
VCR  
/01  
/02  
/03  
/04  
/05  
/06  
/07  
/08  
/09  
Camera 1  
Camera 2  
Camera 3  
Camera 4  
Camera 5  
Camera 6  
Camera 7  
Camera 8  
Camera 9  
MACRO  
RECORD  
FULL  
PIP  
2 x 2  
/P4  
/33  
PIP4  
3 x 3  
/SQ  
/2N  
/FR  
/ZO  
/ST  
/ES  
/UP  
/DO  
/LE  
/RI  
SEQUENCE  
2ND  
FREEZE  
ZOOM  
SET  
ESC  
UP  
DOWN  
LEFT  
RIGHT  
< Table 2 > Front key emulation commands  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Functional remote commands  
HEX  
RESULTS  
HEX  
/X1  
RESULTS  
/S1 Panic record (camera 1)  
/S2 Panic record (camera 2)  
/S3 Panic record (camera 3)  
/S4 Panic record (camera 4)  
/S5 Panic record (camera 5)  
/S6 Panic record (camera 6)  
/S7 Panic record (camera 7)  
/S8 Panic record (camera 8)  
/S9 Panic record (camera 9)  
/AV Stop panic record  
Select camera 1 for display  
Select camera 2 for display  
Select camera 3 for display  
Select camera 4 for display  
Select camera 5 for display  
Select camera 6 for display  
Select camera 7 for display  
Select camera 8 for display  
Select camera 9 for display  
Up (press & hold arrow button)  
Down (press & hold arrow button)  
Left (press & hold arrow button)  
Right (press & hold arrow button)  
/X2  
/X3  
/X4  
/X5  
/X6  
/X7  
/X8  
/X9  
/_U  
/_D  
/_L  
/_R  
/AF Setup Menu  
/AU Factory Reset  
/AD  
/AL  
Alarm History List  
Alarm History List  
/AR Time/Date OSD ON/OFF  
< Table 3 > Remote commands  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix D  
Specifications  
Operating Defaults  
Display Format  
3x3 multi-screen format  
Operation Mode  
Live  
Factory Defaults  
Date Format  
US (MM/DD/YY)  
24-hour  
Time Format  
Clock Source  
Daylight Saving  
Internal clock  
OFF  
Camera Access  
All cameras ON  
All cameras ON  
3 seconds  
3 Seconds  
ON  
Full screen  
03 seconds  
NO (Normally Open)  
AH (Active High)  
ON  
Cameras to Record  
Stack Dwell Time  
Sequence Dwell Time  
Alarm Reset Button  
Alarm Screen Format  
Alarm Dwell Time  
Alarm input Polarity  
Alarm Output Polarity  
Alarm Buzzer  
Alarm Screen  
ON  
Alarm Network Relay  
Alarm Massage Latch  
Alarm Recording  
Alarm Spot Monitor Output  
Alarm Hold Time  
Alarm Action  
OFF  
ON  
INT (Interleaving)  
ON  
20 Seconds  
Timed Out  
1&2  
Alarm Relay  
Alarm Associated  
3 sequential cameras  
followed by alarm camera  
OFF  
Motion Alarm Buzzer  
Motion Alarm Screen  
OFF  
Motion Alarm Network Relay  
Motion Alarm Massage Latch  
OFF  
ON  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Alarm Recording  
Motion Alarm Spot Monitor Output  
Motion Alarm Action  
Motion Alarm Relay  
Motion Alarm Link  
INT (Interleaving)  
OFF  
Timed Out  
OFF  
OFF  
Vloss Buzzer  
ON  
Vloss Screen  
OFF  
Vloss Network Relay  
Vloss Massage Latch  
Vloss Spot Monitor Output  
Vloss Hold Time  
OFF  
ON  
ON  
20 Seconds  
Manual Alarm Buzzer  
Manual Alarm Screen  
Manual Alarm Network Relay  
Manual Alarm Massage Latch  
Manual Alarm Recording  
Manual Alarm Spot Monitor Output  
Manual Alarm Hold Time  
Manual Alarm Action  
Manual Alarm Relay  
Manual Alarm Associated  
Alarm to Macro link  
All Motion Detection  
Motion Detection Timer  
Update/Master  
ON  
ON  
OFF  
ON  
INT (Interleaving)  
ON  
20 Seconds  
Timed Out  
1&2  
OFF  
OFF  
ON  
OFF  
Update  
Normal/Vector  
Normal  
Sensitivity  
10  
Trigger Size (H x V)  
Delay Time  
1 x 1  
0 Seconds  
Motion Hold Time  
5 Seconds  
Target Grids  
VCR Input  
All Grids ON  
BNC  
External Trigger  
OFF  
Panic Record Buzzer  
VCR Type  
VCR Normal Record Time  
VCR Alarm Record Time  
ON  
Standard VHS  
2 Hours, 3 Hours (CCIR)  
2 Hours, 3 Hours (CCIR)  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camera Contrast  
Camera Brightness  
Language  
00  
00  
English  
Mouse  
ON  
Key Lock  
OFF  
Camera Number Offset  
Master/Slave  
OFF  
Slave  
Network Type  
Baud Rate  
RS232  
1200  
Unit Address  
001  
Protocol  
A
Setup Menu Password  
User Change Password  
Password Code  
OFF  
OFF  
User1 (1111)  
User2 (2222)  
User3 (3333)  
User4 (4444)  
Supervisor (5555)  
VCR Picture Adjustment  
Priority Display  
Histogram Equalization  
Border Line  
Live Camera Number  
PB Camera Number  
Live Camera Title  
PB Camera Title  
Live Time, Date  
PB Time,Date  
Vloss Text  
Alarm Text  
Motion Text  
Freeze Text  
Sequence Text  
Motion Box  
00  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video format  
EIA/CCIR  
Standard  
Video Level  
Camera Inputs  
1.0Vp-p, 75 Ohms  
1.0Vp-p, 75 Ohms  
1.0Vp-p, 75 Ohms  
1.0Vp-p, 75 Ohms  
1.0Vp-p,75 Ohms  
1.0Vp-p, 75 Ohms  
Camera Outputs  
Loop through Output  
VCR Input: Composite  
Main Output: Composite  
Auxiliary Output  
Main Output Display Formats (live and playback)  
Full (digital)  
Full (VCR input preview – digital)  
Quad  
9-way  
“Squish” Horizontal (1/2, 1/3)  
“Squish” Vertical (1/2, 1/3)  
PIP with 1 inset (any position, 1/3, 1/4)  
PIP with 2 insets (any position,1/3, 1/4)  
PIP with 3 insets (any position,1/3, 1/4)  
PIP with 4 insets (any position,1/3, 1/4)  
1+7 (3/4 x 1 + 1/16 x 7, 4 configurations)  
1+5 (4/9 x 1 + 1/9 x 5, 4 configurations)  
3+4 (1/4 x 3 + 1/16 x 4, 4 configurations)  
Linear Zoom (1X to 32X) with electronic Pan & Tilt  
Resolution (pixels x lines)  
Sampling  
EIA : 720 x 480  
CCIR : 720 x 576  
Full (Active)  
648 x 448 (648 x 518)  
(10 to 9 down-scaling)  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1/4 Size  
1/9 Size  
324 x 224 (324 x 259)  
216 x 149 (216 x 173)  
162 x 112 (162 x 129)  
432 x 298 (432 x 346)  
486 x 336 (486 x 387)  
720 x 480 (720 x 576)  
analog  
1/16 Size  
4/9 Size  
9/16 Size  
VCR Out (full)  
Spot Out  
Sampling Standard  
Gray Scale  
256 levels  
Video Memory  
Main Display  
VCR Output  
64Mbit SDRAM  
64M/16Mbit SDRAM  
Refresh Rate (fields/sec.)  
Full  
60  
PIP format (Main)  
PIP format (inset)  
Squish  
60  
60  
60  
Split format (1_2 cameras)  
Split format (3-16 cameras)  
Zoom  
60  
60/number of cameras  
60  
Spot Out  
60  
VCR Out (depends on field delay)  
Priority Mode (major)  
Priority Mode (minor)  
60 max  
60  
30/Number of Cameras  
Display Options  
Triplex (Live & Playback at same time)  
Full Sequence  
Cameo Sequence (any 1 position)  
Page Sequence (2x2)  
Freeze All  
Split or PIP mode  
Squish,4-way, 9-way  
Freeze One Camera  
Camera Assign  
Priority Assign (1 cam only)  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Tracking Box  
Digital Contrast Enhancer  
Motion Detection  
Activity Grid  
(16 x 16 grids)  
Activity Detection  
Intrusion Detection  
Motion Vector Sensing (any direction)  
Sensitivity Levels  
Motion Delay Time  
Motion Hold Time  
01-16  
0 to 5 Seconds  
1 to 99 Seconds  
Day & Night Modes (2 setup modes)  
Interleaving (VCR Out)  
Motion Tracking Box (on screen Setup & Live)  
Two-way detecting algorithm  
Update or Master screen mode  
VCR Playback  
Multi-format Decoding (via setup) Dedicated Micros, Robot®,  
Kalatel (Impac), Pelco™ and  
more  
Alarm Operation  
Alarm Inputs  
Alarm Outputs  
Alarm Outputs  
9 inputs with individual polarity  
selection, activated by contact  
closure or TTL/CMOS signal  
relay 2 NO and NC contacts with  
shared common, 1.0A and 24VDC  
(resistive only)  
One output per camera,  
TTL/CMOS (Active High or Low  
selectable)  
Alarm Message Display  
Associated Alarm Setup  
Alarm Dwell Time  
Alarm Hold Time  
Alarm Buzzer  
Up to 4 cameras  
1 to 99 Seconds  
1 to 99 Seconds  
On/Off  
Manual Alarm Activation  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Alarm History Logging  
Alarm History Printout  
Link Alarms to Macro  
Link Alarms to VMD  
256 events  
via RS232  
External Alarm Relay Box  
9 relays via RS485  
On-Screen Display (Main)  
Camera Title  
24 characters  
Time & Date  
U.S., Asia, European  
12/24-hour format  
Alarm Message  
Motion Message  
Video Loss Message  
Zoom Mode Message  
Freeze Mode Message  
Sequence Mode Message  
Setup Menu  
Camera Number  
On-Screen Display (Spot)  
Camera Title  
24 characters  
Time & Date  
U.S., Asia, European  
12/24-hour format  
Alarm Message  
Video Loss Message  
Motion Message  
Sequence Mode Message  
Camera Number  
Other Features (Internal)  
Multi-User Password Protection  
Keylock  
1 Supervisor, 4 Users  
Daylight Saving Time  
Sequence Dwell Time  
Page (Stack) Sequence Dwell Time  
(key press & Menu)  
1 to 99 Seconds, OFF  
1 to 99 Seconds  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Time-lapse VCR Setup (field delay selectable)  
2 hr real-time to 960 hr  
time-lapse  
Video Loss Detection  
Factory Reset  
Unit ID Number  
1 to 255  
Picture Adjust (Live, Playback)  
Macro (1 per camera)  
Macro Scheduler  
Camera Number Offset  
Multilingual Menu  
1 to 256  
English, German, French,  
Italian, Spanish, Polish  
Camera Auto Detect  
Border Color Select  
Record Index List  
Panic Record  
Flash Memory Upgradable  
via RS232  
Other Features (External Interface)  
VCR Trigger Input  
Master/Slave TDG  
Master/Slave Setup  
PC Software Control  
via RS485  
via RS232  
Remote Control  
RS232  
(1200 _ 19200 bps) RX/TX  
(1200 _ 19200 bps) RX/TX  
RS485  
Mouse Control  
Rear Panel Connectors  
Camera Inputs  
9 BNC  
9 BNC  
1 BNC  
1 BNC  
1 BNC  
Loop Out (auto terminating)  
Main Monitor Out (CVBS)  
VCR In (CVBS)  
VCR Out (CVBS)  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Alarm Input/Output  
RS232 (RX/TX)  
RS485 (RX/TX)  
Spot (Aux) Out  
Power  
Terminal block  
Terminal block  
2 RJ45  
4 BNC  
2.1mm pin type; female  
1 5-pin mini DIN  
P/S2 Mouse Port  
Front Panel Controls  
Manual Alarm  
VCR  
Macro  
Panic Record  
Full  
PIP  
2 x 2  
PIP4  
3 x 3  
Sequence  
2nd  
Freeze  
Zoom  
Set  
Esc  
Cameras 1 to 9  
Cursor (up, down, right, left)  
Power Requirements  
12 Vdc, 2.5 Amps  
Power Adapter  
100/240 Vac Universal adapter  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions  
Unit Size  
17"W x 1.73"H x 12.2"D  
432W x 44H x 310D mm  
26"W x 4.8"H x 15.5"D  
660W x 123H x 393D mm  
Shipping Size  
Weight  
Unit Weight  
Shipping Weight  
5.3 lbs (2.4 Kgs)  
9.5 lbs (4.3 Kgs)  
Operating Environment  
Ambient Temperature  
Ambient Humidity  
32° to 95° F (0° to 35° C)  
10% to 90% non-condensing  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Honeywell Video Systems (Head Office)  
171 Eileen Way  
Syosset, NY 11791, USA  
www.honeywellvideo.com  
TEL+1-516-921-6704  
Honeywell Security Australia Pty Ltd.  
Honeywell Video Systems UK Ltd.  
Unit 5, Riverside Centre, 24-28 River Road West  
Parramatta, NSW 2150, Australia  
www.ademco.com.au  
Aston Fields Road, Whitehouse lnd Est  
Runcorn, Cheshire, WA7 3DL, UK  
www.videocontrols.co.uk  
TEL +61-2-8837-9300  
TEL +44-1928-754-000  
Honeywell Security Asia Pacific Ltd.  
Honeywell Security South Africa  
Unit 6 Galaxy Park, Galaxy Avenue, Linbro  
Business Park  
P.O. Box 59904, kengray, 2100, South Africa  
www.honeywell.co.za  
Flat A, 16/F, CDW Building, 388 Castle Peak Road  
Tsuen Wan, N.T., Hong Kong  
www.ademco.com.hk  
TEL +853-2405-2323  
TEL +27-11-574-2500  
Honeywell Security France  
Honeywell Security Germany  
Parc Gutenberg, 13, Voie La Cardon  
91120, Palaiseau, France  
www.ademco.fr  
Großenbaumer Weg 8  
40472 Düsseldorf, Germany  
www.ultrak.com  
TEL +33-1-6932-1090  
TEL +49-211-415-090  
Honeywell Security Italia SpA  
Honeywell Security Poland  
Via della Resistenza 53/59, 20090 Buccinasco  
Milan, ltaly  
www.ademco.it  
TEL +39-02-457-1791  
Chmielewskiego 22a, 70-028  
Szczecin, Polska  
www.ultrak.pl  
TEL +48-91-485-40-60  
Honeywell Security Espana  
Honeywell Security Czech Republic  
Calle Vivero, 5, 28040  
Madrid, Spain  
www.ademco.es  
TEL +34-91-533-4706  
Havránkova 33, Brno  
Dolní Heršpice, 619 00, Czech Republic  
www.olympo.cz  
TEL +420-543-558-111  
Honeywell Security House (Netherlands)  
Honeywell Security Slovakia Republic  
Amperestraat 41  
Vajnorskà 142, 83104 Bratislava  
1446 TR Purmerend, Netherlands  
www.SecurityHouse.nl  
Slovakia  
www.olympo.cz  
TEL +31-299-419-000  
TEL +421-2-444-54-660  
Video Systems  
www.honeywellvideo.com  
1-800-796-CCTV  
Ó 2004 Honeywell International Inc.  
All rights reserved. No part of this publication may be reproduced by any means without written permission  
from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects.  
However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the  
use thereof. The information contained herein is subject to change without notice. Revisions or new editions to  
this publication may be issued to incorporate such changes.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Greenheck Fan Ventilation Hood 459968 User Manual
Greenheck Fan Ventilation Hood SE1 User Manual
Grizzly Air Compressor H3370 User Manual
Grizzly Saw G0717 User Manual
Hasbro Handheld Game System 71 554 User Manual
Hawking Technology Network Card HWC54D User Manual
Health O Meter Thermometer 7605 User Manual
Hoshizaki Ice Maker DB 130H User Manual
HP Hewlett Packard All in One Printer 5700J User Manual
HP Hewlett Packard Personal Computer 120 113 User Manual