Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
Retractable Hose Reel
With 25ft Air Hose
email our technical support at: [email protected]
ITEM 69234
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
©
®
Copyright 2012 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
Save thiS manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
tool use and Care (cont.)
3. Store the tool when it is idle out of reach
of children and other untrained persons.
A tool is dangerous in the hands of untrained users.
5. use only accessories that are identified by the
manufacturer for the specific tool model. Use of
an accessory not intended for use with the specific
tool model, increases the risk of injury to persons.
4. Check for misalignment or binding of moving
parts, breakage of parts, and any other condition
that affects the tool's operation. If damaged,
have the tool serviced before using. Many accidents
are caused by poorly maintained tools.
There is a risk of bursting if the tool is damaged.
Service
1. Tool service must be performed only
3. use only the lubricants supplied with the
by qualified repair personnel.
tool or specified by the manufacturer.
2. When servicing a tool, use only identical
replacement parts. use only authorized parts.
air Source
2. Never use oxygen, carbon dioxide, combustible
gases or any bottled gas as an air source
for the tool. Such gases are capable of
1.
never connect to an air source that is
capable of exceeding 200 psi.
Over pressurizing the tool may cause
explosion and serious injury to persons.
bursting, abnormal operation, breakage
of the tool or serious injury to persons.
Use only clean, dry, regulated compressed air at the
rated pressure or within the rated pressure range as
marked on the tool. Always verify prior to using the
tool that the air source has been adjusted to the rated
air pressure or within the rated air-pressure range.
Safety Symbol Definitions
Symbol
Property or statement
Symbol
Property or statement
WARNING marking concerning
Risk of Respiratory Injury. Wear
NIOSH-approved dust mask/respirator.
Pounds per square inch of pressure
PSi
National pipe thread, tapered
nPt
WARNING marking concerning
Risk of Explosion.
WARNING marking
concerning Risk of Eye Injury.
Wear ANSI-approved eye protection.
Specific Safety instructions
1. The warnings and precautions discussed in this
manual cannot cover all possible conditions and
situations that may occur. It must be understood
by the operator that common sense and caution
are factors which cannot be built into this
3. Install an in-line shutoff valve to allow
immediate control over the air supply in an
emergency, even if a hose is ruptured.
4. WARNING: The brass components of
this product contain lead, a chemical
product, but must be supplied by the operator.
known to the State of California to cause
birth defects (or other reproductive harm).
(California Health & Safety code § 25249.5, et seq.)
2. Obey the manual for the air tool and air
compressor used with this tool.
Save theSe inStRuCtiOnS.
Item 69234
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Functional Description
Specifications
Hose Length
25'
Maximum Air Pressure
Air Inlet
250 PSI
1/4″ -18 NPT
Components and Controls
Guide Roller Bracket
Hose Stopper
Mounting Plate
Inlet from
Compressor
Hose
Support Post
Outlet to tool
Figure a
Reel Drum
initial hose Reel Setup
Read the entiRe imPORtant SaFetY inFORmatiOn section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Repositioning Bracket
1. Remove the Bolts on the Support Post and
reposition to move the guide rollers, if needed, for
the desired mounting location (wall, floor or ceiling).
2. Replace the Bolts and tighten.
mounting Reel
1. Choose a mounting location that is free of electrical
wiring or other obstructions, and is sturdy enough
to support the weight of the Reel and hose as
well as the force used to extend and retract it.
3. Check for hidden wiring, then, drill holes to
accommodate 1/2" bolts (not included).
4. Mount the Reel and secure in place with four bolts.
2. Make a paper template from the mounting
plate of the Reel. Mark the center of the bolt
holes in the desired mounting location.
Page 4
For technical questions, please call 1-800-444-3353.
Item 69234
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating instructions
Read the entiRe imPORtant SaFetY inFORmatiOn section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
inspect tool before use, looking for damaged, loose, and missing parts.
if any problems are found, do not use tool until repaired.
adjust the Spring tension
1. Pull out approximately six feet of Hose.
3. Run the hose back through the guide
and re-attach the hose stopper.
2. Remove the Hose Stopper from the
Hose and slide the Hose out of the Roller
Guide so the Hose is hanging loose.
4. Pull the Hose out several feet to check the tension.
a. To increase tension, wrap the loose hose
one time around the Reel Drum.
b. To decrease tension, unwrap the
hose one time from the drum.
General Operating instructions
1. Check the Wheel operation by slowly pulling the
Hose out. You should hear a clicking noise.
4. Attach a coupler (sold separately) to your
air compressor hose and apply thread
seal tape to the Inlet fitting on the Reel.
Connect the coupler to the Inlet fitting.
2. To lock the Hose, pull it out a minimum
of 1/2 revolution and it will stay locked
after the first, second, or third click.
5. Connect your air tool to the other end of the Hose
using another coupler and thread seal tape.
3. To unlock, slowly pull until the clicking stops, and let
it retract until the Hose Stopper hits the Hose Guide.
6. Follow all instructions from the air tool
and compressor for set up and use.
CautiOn: Hold on to the Hose while it is
rewinding, to avoid damage to the Hose Reel.
7. When finished using the Hose, disconnect
the air tool and retract the hose. Wipe the
Hose Reel clean with a dry cloth.
Item 69234
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
user-maintenance instructions
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
tO PRevent SeRiOuS injuRY:
Detach air supply from this product before performing any inspection, maintenance, or cleaning procedures.
tO PRevent SeRiOuS injuRY FROm tOOl FailuRe:
Do not use damaged equipment. if abnormal noise, vibration,
or leaking air occurs, have the problem corrected before further use.
Cleaning, maintenance, and lubrication
note: These procedures are in addition to the regular checks and maintenance
explained as part of the regular operation of the Hose Reel.
1. BeFORe eaCh uSe, inspect the general
2. aFteR eaCh uSe, re-wind the hose onto the reel
condition of the tool. Check for:
and wipe the Hose Reel clean with a dry cloth.
• loose hardware or housing,
WaRninG! Internal spring is not user-
• misalignment or binding of moving parts,
• cracked or broken parts, and
serviceable or user-replaceable.
• any other condition that may
affect its safe operation.
hose Replacement
1. Remove the Hose Stopper from
the hose and set aside.
5. Use thread seal tape on the hose fitting threads
and screw the fitting onto the swivel and tighten.
2. Pull out the old Hose and securely
lock the Hose Reel.
6. Attach the Hose Stopper on the end of
the Hose near the Outlet fitting.
3. Disconnect the old hose from the swivel
joint and remove the hose.
7. Carefully release the Drum Latch and allow
the Hose to wind onto the reel, evenly
distributing the Hose across the Reel.
4. Run the new hose through the Guide Roller
and through the opening in the drum flange.
Page 6
For technical questions, please call 1-800-444-3353.
Item 69234
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts list and Diagram
Part
Description
Spring Canister
Drum (air inlet side)
Drum (mounting
bracket side)
Qty
Part
Description
Qty
1
1
1
1
1
3
7
1
2
1
1
3
3
2
3
Part
Description
Qty
1
2
3
1
1
1
11 Locking Cam
27 Roller Guide
Bracket Assembly
1
12 Spring
13 Axle
14 Lock Washer
15 Nut
16 Bolt
17 Nut
18 Clamp
20 Bolt
21 Washer
22 Nut
23 Washer
24 Bolt
25 Nut
28 Hose Stopper
Assembly
29 Ratchet Locking Gear
30 Spacing Washer
31 Retaining Ring
32 Bolt
33 Lock Washer
34 Setscrew
35 Spacing Washer
36 Nut
1
4
5
Mounting Bracket
Guide Arm
1
1
1
1
2
1
1
4
4
1
1
4
1
1
6A Air lnlet Valve Body
6B Air lnlet Valve
Swivel Collar
7
8
9
Hose
1
1
1
Spring Hose Guard
Hub Bearing
Assembly
37 Spacing Washer
38 Pin
10 Bolt
1
26 Lock Nut
Record Product's Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Item 69234
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
PleaSe ReaD the FOllOWinG CaReFullY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
|