led work light
66308
Set up And operAting inStructionS
®
distributed exclusively by harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SAVe thiS mAnuAl.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described
herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
Many accidents are caused by
poorly maintained items.
nia Health & Safety Code § 25249.5,
et seq.)
5. Service
6. The warnings, precautions, and
instructions discussed in this instruc-
tion manual cannot cover all possible
conditions and situations that may
occur. It must be understood by the
operator that common sense and cau-
tion are factors which cannot be built
into this product, but must be supplied
by the operator.
a. have the light serviced by a
qualified repair person using
only identical replacement parts.
This will ensure that the safety of
the Light is maintained.
light Safety warnings
1. Maintain labels and nameplates on
the Light. These carry important
safety information. If unreadable or
missing, contact Harbor Freight Tools
for a replacement.
SAVe theSe
inStructionS.
grounding
2. Do not leave the Light unattended
when it is plugged into an electrical
outlet. Turn off the Light, and unplug
it from its electrical outlet before leav-
ing.
improperly
connecting the
grounding wire can result in
electric shock.
Check with a qualified
3. This product is not a toy. Keep it out
of reach of children.
electrician if you are in doubt
as to whether the outlet is
properly grounded. do not
modify the power cord plug
provided with the tool. never
remove the grounding prong
from the plug. do not use the
tool if the power cord or plug
is damaged. if damaged, have
it repaired by a service facility
before use. if the plug will not
fit the outlet, have a proper
outlet installed by a qualified
electrician.
4. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close prox-
imity to heart pacemaker could cause
pacemaker interference or pacemaker
failure. In addition, people with pace-
makers should:
• Avoid operating alone.
• Properly maintain and inspect to
avoid electrical shock.
• Any power cord must be prop-
erly grounded. Ground Fault Circuit
Interrupter (GFCI) should also be
implemented – it prevents sustained
electrical shock.
5. WARNING: Handling the cord on
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (Califor-
SKU 66308
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
preceding illustration. (See 3-prong
plug and outlet.)
grounded tools:
tools with three prong plugs
double insulated tools:
tools with two prong plugs
1. Tools marked with “Grounding Re-
quired” have a three wire cord and
three prong grounding plug. The
plug must be connected to a properly
grounded outlet. If the tool should
electrically malfunction or break down,
grounding provides a low resistance
path to carry electricity away from
the user, reducing the risk of elec-
tric shock. (See 3-prong plug and
outlet.)
1. Tools marked “Double Insulated” do
not require grounding. They have
a special double insulation system
which satisfies OSHA requirements
and complies with the applicable stan-
dards of Underwriters Laboratories,
Inc., the Canadian Standard Associa-
tion, and the National Electrical Code.
(See outlets for 2-prong plug.)
2. The grounding prong in the plug is
connected through the green wire in-
side the cord to the grounding system
in the tool. The green wire in the cord
must be the only wire connected to
the tool’s grounding system and must
never be attached to an electrically
“live” terminal. (See 3-prong plug
and outlet.)
2. Double insulated tools may be used
in either of the 120 volt outlets shown
in the preceding illustration. (See
outlets for 2-prong plug.)
extension cords
1. Grounded tools require a three wire
extension cord. Double Insulated
tools can use either a two or three
wire extension cord.
3. The tool must be plugged into an
appropriate outlet, properly installed
and grounded in accordance with all
codes and ordinances. The plug and
outlet should look like those in the
2. As the distance from the supply outlet
increases, you must use a heavier
gauge extension cord. Using exten-
sion cords with inadequately sized
wire causes a serious drop in voltage,
resulting in loss of power and possible
tool damage. (See table A.)
3. The smaller the gauge number of the
wire, the greater the capacity of the
cord. For example, a 14 gauge cord
SKU 66308
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
can carry a higher current than a 16
gauge cord. (See table A.)
Symbology
4. When using more than one exten-
sion cord to make up the total length,
make sure each cord contains at least
the minimum wire size required. (See
table A.)
Double Insulated
Canadian Standards
Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
5. If you are using one extension cord
for more than one tool, add the name-
plate amperes and use the sum to
determine the required minimum cord
size. (See table A.)
V~
A
No Load Revolutions per
Minute (RPM)
n xxxx/min.
0
6. If you are using an extension cord
outdoors, make sure it is marked with
the suffix “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor
use.
7. Make sure the extension cord is
properly wired and in good electrical
condition. Always replace a damaged
extension cord or have it repaired by
a qualified electrician before using it.
8. Protect the extension cords from
sharp objects, excessive heat, and
damp or wet areas.
recommended minimum wire
gAuge For eXtenSion cordS*
(120/240 VOLT)
eXtenSion cord
nAmeplAte
AmpereS
length
(at full load)
0 – 2.0
2.1 – 3.4
3.5 – 5.0
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* Based on limiting the line
voltage drop to five volts at
150% of the rated amperes.
tABle A
SKU 66308
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SpeciFicAtionS
operAting inStructionS
read the entire importAnt
SAFetY inFormAtion
Electrical Requirements 110 V~ / 60 Hz / 4.4 W
Light Strength
270 Lumens
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
unpAcking
When unpacking, make sure that
the item is intact and undamaged. If any
parts are missing or broken, please call
Harbor Freight Tools at the number shown
on the cover of this manual as soon as
possible.
1. Position the LED work light near the
work. Loosen Knob (3) and adjust
Lamp Assembly (1) to direct the light
beam. Tighten the Knob (3).
2. Plug the Light into a grounded 110V
electrical outlet.
initiAl Set up
inStructionS
3. To prevent accidents, disconnect the
power supply after use. Clean, then
store the tool indoors out of children’s
reach.
read the entire importAnt
SAFetY inFormAtion
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
to preVent
SeriouS injurY
From AccidentAl
operAtion:
unplug the light from the
electrical outlet before
assembly.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
1. Slide the Base (2) into the bottom of
the Lamp Assembly (1).
2. Secure with the Knob (3).
reV 09b
SKU 66308
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
uSer-mAintenAnce
pArtS liSt
inStructionS
part
description
Qty
1
1
Procedures not specifically
explained in this manual must
be performed only by a qualified
technician.
1
2
3
Lamp Assembly
Base
Knob
1
ASSemBlY diAgrAm
to preVent
SeriouS injurY
From AccidentAl
operAtion:
unplug the light from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
1
to preVent SeriouS
injurY From tool
FAilure:
do not use damaged
equipment. if abnormal noise
or vibration occurs, have the
problem corrected before
further use.
cleaning, maintenance, and
lubrication
3
2
1. BeFore eAch uSe, inspect the
general condition of the tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical wir-
ing, and any other condition that may
affect its safe operation.
record product’s Serial number
here:
Note: If product has no serial number,
record month and year of purchase
instead.
2. AFter uSe, clean external surfaces
of the tool with clean, moist cloth.
3.
wArning! if the supply cord of
this power tool is damaged, it must
be replaced only by a qualified
service technician.
Note: No replacement parts.
SKU 66308
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
limited 90 dAY wArrAntY
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser that this
product is free from defects in materials and workmanship for the period of 90 days
from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of
maintenance. We shall in no event be liable for death, injuries to persons or property,
or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or con-
sequential damages, so the above limitation of exclusion may not apply to you. THIS
WARRANTy IS ExPRESSLy IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITy AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection verifies the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 66308
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|