12 Volt, 80 lb.
AtV SPREADER
99621
SEt uP AnD oPERAting inStRuctionS
®
Distributed exclusively by Harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE tHiS mAnuAl.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Wear thick jeans and
steel-toed work boots to
help prevent injury
3. Never attempt to install this ATV
Spreader to the ATV vehicle alone.
Have another adult assist when at-
taching or detaching.
caused by flying debris.
10. Stay alert - Watch what you are
doing. Use common sense. Do not
operate ATV Spreader when you are
tired.
4. Refer to the material packaging, or
bag safety instructions when handling
all materials to be applied with this
Spreader.
11.
Do not grasp the exposed 5. Before attaching this ATV Spreader,
turning Plate (16) edges
when picking up or hold-
ing the Spreader.
consideration must be given to the
load capacity of the vehicle to be
loaded. Be sure to account for the
weight of this Spreader and the
weight of the material being spread.
12. Do not use in Rain, or damp loca-
tions.
6. Maintain labels and nameplates on
the appliance. These carry important
safety information. If unreadable or
missing, contact Harbor Freight Tools
for a replacement.
13. All visitors should be kept at a dis-
tance from work area.
14. When servicing use only identical
replacement parts.
7. The warnings, precautions, and in-
structions discussed in this instruction
manual cannot cover all possible con-
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
15. Store Idle ATV Spreader Indoors, out
of reach of children.
16. Maintain ATV Spreader With Care.
Follow instructions for lubrication.
Check for damaged parts. If anything
irregular is found, the damage should
be properly repaired by a qualified
technician unless indicated else-
where in this manual.
SAVE tHESE
inStRuctionS.
17. Disconnect the AtV Spreader when
not in use and/or before servicing.
Specific Safety Rules
SPEciFicAtionS
1. Care must be taken when lifting this
ATV Spreader so as not to cause
equipment damage and/or personal
injury.
Hopper
80 LB. Weight capacity.
Assembly
1900 cu. in. Storage capacity
Capacity
Drive Motor
12V Electric
2. Remove any material in Hopper As-
sembly (8) before removing this ATV
Spreader from the vehicle.
SKU 99621
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
unPAcking
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
SEt uP inStRuctionS
Read the EntiRE imPoRtAnt
SAFEty inStRuctionS
Figure 1
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Switch box installation:
WARning: To prevent serious injury,
make sure the ATV is OFF before install-
ing The Switch Box Assembly (31) .
note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
1. Attach the Switch Box Assembly (31)
to your ATV. Route cable ties through
the two slots located on the Switch
Box Assembly (31) and connect them
onto the ATV Frame.
Assembly
1. The ATV Spreader comes partially
assembled.
notE: Make sure the Switch Box As-
sembly (31) is secure before proceeding.
2. Mount the two sides of the Frame
Rail (21) to the Hopper Assembly (8)
using Screws M5 x 35 (14).
2. Connect the ATV Battery Terminals
(31-3) to battery. Connect the white
wire to the battery’s positive pole,
connect the black wire to the battery’s
negative pole .
3. Position the Gauge Assembly (22)
to either Frame Rail (21) based on
whether the Hopper Assembly (8) is
to be mounted on the front, or rear
rack of the ATV. If mounted on the
rear rack, the Control Handle (25)
should be on the right Frame Rail
(21). If mounted on the front rack,
place the Control Handle (25) on the
Left Frame Rail (21). See Figure 1
below.
3. Connect the Motor Terminal (31-4) to
the Electric Motor (3) terminal.
4. Connect the ATV Battery Terminals
(31-3) to the Motor Assembly using
the Harness Connector. See parts list
and assembly diagram page 7 and 8.
REV 08g; 09a
SKU 99621
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. An Adjustable Solid Stop is provided
to allow the operator to adjust the
Gauge Assembly (22) to the desired
opening, allowing the correct amount
of material to fall onto the Turning
Plate (16) for disbursement. The
“Solid Stop” will allow the operator to
repeat the opening/closing without
having to look at the control while op-
erating the vehicle. It is set by using
the Thumb Wing Nut (24) located on
the Gauge Assembly (22). Establish
the correct opening, then lock down
the Thumb Wing Nut (24).
How to Attach to your AtV
1. Place the ATV Spreader (assembled),
centered on the front, or rear luggage
rack of your ATV. Use the J-Bolts
(34), Press Plate (33) and Hex Nuts
(32) to connect Frame Rail (21) to the
luggage rack cross bar closest to the
seat, or handlebars. Use the J-Bolts
(34), Press Plate (33) and Hex Nuts
(32) to attach the Spreader to the
luggage rack, securing it to the outer
most rail on the luggage rack.
2. WARning: Prior to each use, inspect
the mounting hardware and the ATV
Spreader to ensure the tightness of
the mount. If any hardware is loose,
tighten securely before using the unit.
3. Measure off a distance of 50 feet on
the surface you will be working. See
number 9 below.
4. Weight out enough of the material to
fill the Hopper Assembly (8) at least
half full. Record the weight for further
use.
Functions
1. This ATV Spreader can be used to
spread grass seed, fertilizer pellets,
sand, ice-melt and any other type of
seed or loose pellet type lawn care
products.
5. Set the Adjustable Solid Stop on the
Gauge Assembly (22) to the desired
opening and tighten the Thumb Wing
Nut (24).
2. notE: Not for powdered lawn prod-
ucts which are hard to adjust spread
rates, or for heavy, mulch-type prod-
ucts which will clog the Turning Plate
(16).
6. notE: Usually an approximate
spreading rate is listed in material di-
rections, or on the bag of the specific
material you will use.
7. As you start driving the ATV through
the work area, open the Control
Handle (25) till it stops against the
Adjustable Solid Stop.
oPERAting inStRuctionS
Read the EntiRE imPoRtAnt
SAFEty inFoRmAtion section
at the beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
8. Continue to spread the material till
you cross the end of the area you are
working. Close the Control Handle
(25) to stop the flow of material onto
the Turning Plate (16).
1. Before operating the ATV Spreader,
put on ANSI-approved safety goggles
and other safety gear (not supplied).
SKU 99621
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Empty the Hopper Assembly and
re-weigh the material. By taking note
of how much material you used and
how wide the spreading area was,
you can figure the correct rate of
spread. This will help you maintain
the correct spreading rate for your
project.
er. Check for loose screws, misalign-
ment or binding of moving parts,
cracked or broken parts, damaged
electrical wiring, and any other condi-
tion that may affect its safe operation.
2. AFtER uSE, clean external surfaces
with clean, moist cloth.
3. Clean out the Hopper Assembly and
using a shop vacuum (not supplied),
clear all leftover material from the
Turning Plate (16) and other areas of
the Spreader.
10. To prevent accidents, turn off the ATV
and disconnect the ATV Spreader
after use. Clean, then store indoors
out of children’s reach.
4. Rinse the ATV Spreader with a hose
and fresh clear water. Let dry before
storing indoors away from children.
mAintEnAncE AnD
SERVicing
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
5. notE: If the ATV Spreader is to be
left outside between jobs, always
cover with the Rain Cover (1) to
protect both the Spreader and any
material that may be in the Hopper
Assembly (8).
to PREVEnt
SERiouS injuRy
FRom AcciDEntAl
oPERAtion:
PlEASE READ tHE FolloWing
cAREFully
turn the Power Switch of the
vehicle to its “oFF” position
before performing any
inspection, maintenance, or
cleaning procedures.
THE MANUFACTURER AND/OR DISTRIBUTOR
HASPROVIDEDTHEPARTSLISTANDASSEMBLy
DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOLONLy. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANy REPRESENTATION
OR WARRANTy OF ANy KIND TO THE BUyER
THAT HE OR SHE IS qUALIFIED TO MAKE ANy
REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS qUALIFIED TO REPLACE ANy PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR ExPRESSLy STATES
THATALLREPAIRSANDPARTSREPLACEMENTS
SHOULD BE UNDERTAKEN By CERTIFIED AND
LICENSED TECHNICIANS, AND NOT By THE
BUyER. THE BUyER ASSUMES ALL RISK AND
LIABILITyARISINGOUTOFHISORHERREPAIRS
TOTHEORIGINALPRODUCTORREPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
to PREVEnt SERiouS
injuRy FRom tool
FAiluRE:
Do not use damaged
equipment. if abnormal noise
or vibration occurs, have the
problem corrected before
further use.
cleaning, maintenance, and
lubrication
1. bEFoRE EAcH uSE, inspect the
general condition of the ATV Spread-
SKU 99621
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
troubleshooting
Problem
Possible causes
likely Solutions
Control Handle will
not open/close Gauge
Assembly.
1. Material clogging port of Gauge
Assembly (22) and/or Adjustment
Plate (13).
1. Check both Gauge Assembly (22)
and Adjustment Plate (13) and clear
debris if necessary.
Material not spreading 1. Wrong opening on Gauge Assembly 1. Loosen Thumb Wing Nut (24) and
at proper rate.
(22).
open/close accordingly and re-
adjust if necessary.
Follow all safety precautions whenever diagnosing or servicing the
appliance. turn off AtV and remove Spreader from vehicle before
service.
PARtS liSt
Part # Description
q’ty Part # Description
q’ty
1
1
Rain Cover
1
1
1
1
1
2
1
1
4
2
1
1
1
4
1
1
3
1
1
20
21
22
23
24
25
26
27
28
29
30
31
Hex Bolt M6x30
Frame Rail
2
Electric Motor Lid
Electric Motor
2
3
Gauge Assembly
Spacer
1
4
Electric Motor Cover
Tie
1
5
Thumb Wing Nut M6
Control Handle
2
6
Unlock Nut
1
7
Motor Support
Hopper Assembly
Flat Washer
Wire Adjustment Clip B
Wood Screw M4.5x18
Adjustment Wire
Phillips Screw M6x15
Lock Washer
1
8
2
9
1
10
11
12
13
14
15
16
17
18
19
Hex Bolt M6x15
Wire Clamp
2
2
Wire Adjustment Clip A
Adjustment Plate
Screw M5x35
Switch Box Assembly
1
31-1 Fuse
1
31-2 Switch
1
Center Spacer
Turning Plate
31-3 ATV Battery Terminals
31-4 Motor Terminal
1
1
Wood Screw M4.5x10
Phillips Screw M4x20
Phillips Screws M6x45
32
33
34
Hex Nut M6
Press Plate
J-Bolt
8
4
8
Record Product’s Serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
REV 08g
SKU 99621
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEmbly DiAgRAm
Harness
connector
REV 08g
SKU 99621
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|