HAND HELD SAW MILL
92247
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect
tool cords periodically and, if damaged, have them repaired by an authorized
technician. The handles must be kept clean, dry, and free from oil and grease at all
times.
10. Disconnect power. Unplug band saw when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches
are removed from the tool or machine work surface before plugging it in.
12. Avoid unintentional starting. Be sure the band saw switch is in the Off position
when not in use and before plugging in.
13. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
14. Take caution as some woods contain preservatives such as copper chromium
arsenate (CCA) which can be toxic. When cutting these materials extra care should
be taken to avoid inhalation and minimize skin contact.
15. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified
technician. Do not use the tool if any switch does not turn On and Off properly.
16. Guard against electric shock. Prevent body contact with grounded surfaces such
as pipes, radiators, ranges, and refrigerator enclosures.
17. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.
18. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.
19. Maintenance. For your safety, service and maintenance should be performed
regularly by a qualified technician.
20. Band Saw Precautions. Read and understand the Band Saw Operation Manual and
follow all operational, safety warnings and precautions therein before each use.
21. Use tools with both hands when required. Many tools such as this Saw Mill, and
chain saws, drills, routers, etc., require the use of both hands when operating. This
helps maintain tool stability and keeps hands away from the working area of the tool.
Warning: The brass components of this product contain lead, a chemical known to the
State of California to cause birth defects (or other reproductive harm). (California Health
& Safety Code 25249.5 et seq.)
Page 3
SKU 92247
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Product Specific Safety Precautions
1.
Before using, read all instruction and safety warnings provided in the instruction
manual provided with the Band Saw being used.
2.
3.
4.
5.
Verify that all Band Saw safety devices are installed correctly.
Verify that the saw blade is sharp and at proper tension.
Check that all saw blade guides are in place and properly adjusted.
Never leave the band saw unattended while running. Turn power off and wait until the
blade stops before adjusting the Saw Mill.
6.
Before turning on the Band Saw, place the Saw Mill with attached log on the Band
Saw Table and make Fence depth adjustments. Verify that the log mounting screws
will not come into contact with the saw blade during a cut.
7.
8.
Before using the Saw Mill, make sure that all its assembly screws are tight.
This product is designed to be used only with Band Saws.
Warning:The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts are included. Also refer to the
Parts List and Assembly drawing located at the end of this manual. If any parts are missing
or broken, please call Harbor Freight Tools at the number on the cover of this manual as
soon as possible.
Bushing (7)
Handles (5)
Mounting Plate (6)
Flathead Screw
Base Plate (2)
Acme Screw with Knob (8)
Slide Plate (4)
Back Plate (3)
Guide Slide with
Adjustment Plate (1)
Page 4
SKU 92247
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
To assist in assembly, refer to the photo on the previous page and the Assembly Drawing at
the end of this manual. When inserting screws, be careful that they thread correctly so they
do not strip threads.
1.
Using two flathead screws, attach the Guide Slide with Adjustment Plate (1) to the
underside of the Base Plate (2).
Before tightening the screws, place the Guide Slide with Adjustment Plate into the
guide slot on the Band Saw Table. Move the Adjustment Plate (1) to fit the size of the
guide slot. Securely tighten screws.
Screw holes to mount
the Back Plate (3)
Flathead Screws
Base Plate (2)
Adjustment Plate
Guide Slide (1)
2.
3.
4.
5.
Mount the Back Plate (3) to the top of the Base Plate (2) using two flathead screws
from the bottom of the Base Plate (2). Securely tighten screws.
Using two flathead screws, attach the Bushing (7) to the Back Plate (3). Do not fully
tighten screws.
Attach the Mounting Plate (6) to the Slide Plate (4) using three flathead screws from
the bottom of the Slide Plate.
Insert the Slide Plate (4), with Mounting Plate (6), into its track on the Base Plate (2).
Slide in far enough to expose the Handle mounting holes in the end of the Slide Plate
(4) as shown in the photo on page 4.
6.
Attach the Handles (5) to both the Mounting Plate (6) and Slide Plate (4) using four
flathead screws.
7.
8.
Carefully screw in the Acme Screw with Knob (8) through the Bushing (7).
Turn the Acme Screw with Knob (8) clockwise until its end goes into the center hole in
the Mounting Plate (6). Secure with a flathead screw. See photo on page 6, left side.
9.
Center the Bushing (7) on the hole in the Back Plate (3) and securely tighten screws.
10. Turn the Acme Screw with Knob (8) clockwise until the end Bushing force-fits into the
Mounting Plate center hole.
Page 5
SKU 92247
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
1.
2.
Select a dry log or other wood stock to cut.
The stock should be no longer than the band saw table. Otherwise, the Saw Mill
Guide Slide (1) may come out of the table guide slot. Check for preexisting nails or
screws in the wood stock and remove before cutting.
Turn the Acme Screw Knob (8) counterclockwise to bring the Mounting Plate all the
way back.
3.
4.
Place the Saw Mill on a flat surface to mount the wood stock.
Select the side of the wood stock for the first cut, and place the opposite side against
the Mounting Plate (6).
5.
Select holes on opposite ends of the Mounting Plate (6) to insert holding screws (not
supplied). Screw in until wood stock cannot move. Use at least one screw at each
end. See photo below-left.
Use 1-1/4 inch wood or sheet-rock screws. For irregular shaped wood stock, find a
hole in the Mounting Plate that comes the closest to the surface of the wood stock.
This will keep the wood stock more stable during cutting.
Mounting Plate (6)
Band Saw Head
Table Guide Slot
Up to 16 screw holes to
mount wood stock
6.
Place the Saw Mill, with attached wood stock, on the band saw table. Insert the Guide
Slide (1) into the Table Guide Slot. See photo above-right.
7.
8.
Adjust the band saw head up to clear the wood stock being cut.
Determine the depth of cut by measuring from the saw blade to the outer edge of the
wood stock.
If a deeper cut is to be made, turn the Acme Screw Knob (8) clockwise. If a thinner cut
is to be made, turn Knob counterclockwise. As an estimate, each full turn of the Knob
equals about 1/8 inch.
Caution: Always be aware of the depth of the mounting screws so the saw blade does
not come into contact while cutting the wood stock.
Page 6
SKU 92247
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
With the Saw Mill and wood stock already in place, turn on the band saw and allow it
to come to full speed before continuing.
Caution:Avoid injuries. Always keep both hands and arms on one side of the saw blade.
Never cross over the saw blade.
10. To begin cutting, place each hand on one Handle (5) and push the wood stock into the
saw blade.
Push with a parallel movement to the saw blade in a smooth, even motion. Let the saw
blade cut at its own speed. Do not force the wood stock into the saw blade.
11. When the cut is complete, immediately shut off the band saw.
Wait for the saw blade to stop before handling the wood stock and Saw Mill.
12. For the second and subsequent cuts, remove the mounting screws and rotate the
wood stock. Replace mounting screws. Repeat steps 5 through 11. Only rotate the
wood stock when the Band Saw is turned OFF.
Maintenance
1.
2.
3.
Before each use, ensure all assembly screws are tight.
Periodically apply a light oil to the Acme Screw (8).
Store in a clean and dry location.
Parts List
Item
1.
Description
Guide Slide with
Adjustment Plate
Base Plate
Back Plate
Slide Plate
Handle
Mounting Plate
Bushing
Qty
1
2.
3.
4.
5.
6.
7.
8.
1
1
1
2
1
1
1
Acme Screw with Knob
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as
replacement parts.
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS
MANUAL AS A REFERENCETOOL ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR
SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.
Page 7
SKU 92247
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Drawing
Page 8
SKU 92247
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
|