HWM90-98
Computerized Full-auto
Washing Machine
Contents
Before using
Names of the parts..........................The 2nd cover
Safety precautions...............................................1
Installation and adjustment.................................3
Install the water inlet hose....................................5
Using Process
Preparation before washing.................................7
Put in the laundries..............................................8
Use of the detergent...........................................9
Use the operation buttons.................................10
Close the top lid................................................14
Finish washing..................................................14
Disposal after washing......................................15
Trouble shooting answer to question................16
Packing list................................................17
Please read this manual carefully before using.
Retain it for future reference
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
The manufacturer will not bear the responsibility for
those risks occurred from not obeying this manual.
Specification table
The back cover
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Before Using
The washing machine must be positioned
so that the plug is accessible. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
c l e a n i n g t h e m a c h i n e . D o n o t p l u g
or pull the power plug with wet hand.
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
Earth
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,please wipe with
dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or the after-sale service department.
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
Do not use water hotter than 50
The ventilation
holes at the bottom
Soft object
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Before Using
Do not decompose, repair or alter the machine
by yourself.
Do not stretch hands into the working machine.
It is dangerous even if the rotation is slow.
Take special care of the children.
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
Do not put any hot or heavy items (such as the kettle
with hot water) on the washing machine
Benzene
The appliance is not instruct for use of
young children of infirm persons without
supervision.Young children should be
supervised to ensure that they do not
play with the appliance.
Keep the machine away from direct sunlight and
heat source like the heater.
To prevent your laundries and washing machine from
damages, be sure to take out all of the foreign materials
from your pocket, such as coins, buttons, sandor hair
pins etc.
The lint filter shall be kept in good condition, and
installed to proper position. If the lint filter is lost
or damaged, please contact the local after-sales
service department of our company.
Before washing, please check if the water tap is open,
and if the water inlet pipe is connected properly.
Install
Dismantle
It is suggested to use low-foaming washing powder.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and adjustment
Before Using
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Install the inner cover components
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming
Outer tub cover
the inner cover shaft to the installation hole of the corresponding
outer tub cover shaft groove.
shaft groove
Inner cover shaft
3.Firstly insert the inner cover shaft of I side into the correspon
-ding outer tub cover shaft groove, then push the another inner
cover shaft into the corresponding outer tub cover shaft groove.
Please install to designated position to guarantee there are no
dropping or abnormal sound in opening and closing of the inner
cover, and the operation shall be smooth. Do not dismount the
inner cover component after washing.
Outer tub cover
Inner cover
Install the bottom plate
After opening the package, please lean
the washing machine gently down on
soft items (like towel cloth, blanket, etc.).
Install the bottom plate to the bottom
of the machine with eight screws by a
c r o s s s c r e w d r i v e r, t h e n l i f t t h e
machine up gently. See to the figure:
Back
Front
Bottom plate
Soft items
Screw
Adjust the Installation position
The largest allowed slope of the shank base of the machine is 2 . The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal
Hang the plumb to confirm it's horizontal
Adjust the adjustable foot
(1) To twist the adjustable foot at the right front of
the cabinet (front the sight of front), please first
lift up the side of the foot slightly, loosen the
adjustable nut, and twist the foot.
adjustable nut
adjustable foot
Loosen
Fasten
High
Low
(2) Fasten the nut after adjustment.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
How to change the direction of the drain hose
1.Lean the machine down gently with the front
surface facing the ground. Loosen the eight
screws by a cross screwdriver.
3.Extend the drain hose from the right side. Push the
drain hose into the groove with hands.
Back
Bottom plate
Front
Soft item
2.Pull out the drain hose from the groove at the left side.
Use groove at
this side after
direction changing
4.Install the bottom plate (as per indicated before),
then lift the machine up gently.
Page 3
Usage of the drain hose
The drain hose shall drain smoothly
1.The height of the drain hose shall be
less than 10cm, or the drainage will not
be smooth, and cost such long time that
the machine may stop at mid way.
4.If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
2.Do not ramp or press the drain hose.
3.If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
5.If the extra hose is too long, cut it
either at A or at B point.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the water inlet hose Before Using
Confirm the water faucet
water faucet, suitable
water faucet, not suitable
The exit end face of the faucet
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise
it may leak water. See to Figure 3.)
water inlet hose jointer
Screw
Slider
Nameplate
Bushing
Lock level
Screw knife
water inlet hose
Figure 1
Figure 2
Figure 3
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Remark: .Before twisting the fastening nut, the threading is 4mm above the upper
surface of the nut. After twisting, the threading is less than 2mm above the upper
surface of the nut. See to Figure 6
about 4mm after twisting
About above 2mm after twisting
Screw nut
Figure 4
Figure 5
Figure 6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
Connection between the water inlet hose and the washer
1.Do not take off the water absorption cushion. Please check if the
cushion is dropped or damaged before each usage. If it happens
please contact our after-sale department immediately.
nut of the water inlet hose
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
jointer of the water inlet valve
water absorption cushion.
Connection between the jointer of the water inlet hose
and the water inlet hose
1.Push down the slider. Insert the water inlet hose into the jointer.
the jointer of the water inlet hose
Slider
2 Hang the lock lever to the jointer. Release the slider till a click sound is heard.
Locking level
Check the connection between the jointer of the water inlet hose
and the water faucet
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
Dismantle the water inlet hose
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet hose.
If the machine is used frequently, the jointer of the water inlet hose can be kept
on the faucet to prevent damaging the fixing screw.
Locking level
Slider
Remarks: use the new hose sets supplied with the washer.
Any other old hose sets should not be used.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Preparation before washing
Using process
Preparation before washing
1.Connect the water inlet hose. Open the water faucet.
2.Confirm that the washing machine is earthed reliably.
Then insert the power plug into the receptacle. The
earth terminal shall not link to gas pipeline and faucet
water pipeline.
3.Put down the drain hose.
Pay attention to following before washing
The quantity of
When the pulsator
is running, the but-
tons of the laundri-
es may cause noi-
se. For the sake of
discretion, please
put the laundries
with buttons into
other laundries.
Check if the
Tie the long
Clear the pocket.
Pay attention to followings before washing the laundries
the laundries
shall not be too
large. Stretch
and loosen the
laundries before
putting them in
the tub.
laundries has
special requi-
rement on w-
ashing
strips; fasten
the buttons;
close zippers.
Take out the coi-
ns, sand, hairpins
etc.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust.
For the parts with heavy soil, please apply detergent on them in advance, which
can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before
putting in.
f. Do not put those laundries polluted by chemicals into the washing machine directly.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Put in the laundries
Using process
The capacity of washing and spinning of the machine
refer to the largest weight of the standard laundries
under dry condition that can be washed or spinning
in one time. One time washing quantity shall be lower
than the rated capacity. The largest capacity of this
machine is 9.0kg.
The thickness, size, type of the cloth will influence the
actual washing capacity. It is suitable for one time
washing to put in reasonable amount of laundries
and the laundries can be turned round in washing.
Do not select above 4 water level for laundries small
than 1.0kg, so as to avoid splashing of water.
Reference weight of the laundries:
working suit up,down
cotton,about 1120g
jeans about 800g
blanket
cotton,about 900g
blending coat
about 800g
pajamas
about 200g
jacket
cotton,about
800g
shirt
cotton,about
300g
single bed sheet
cotton,about 600g
undershirt
cotton,about 180g
socking
blending,about 50g
underpants
cotton,about 70g
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Use the operation buttons
Using process
Description of the function of the buttons
Mode and meaning of the indicator
Digital tube
During sensing, it displays "--"
the frame of the indicator is on : indicate the program about to run,
or indicate the selected mode
During operation of programs, it displays the
remained time (minute) or remained times of
the corresponding procedure
The digital tube corresponding to the running
program lights.
MINUTES
MINUTES
TIMES
MINUTES
DOUBLE DRIVE WASH
DIGITAL TUBE DISPLAY
WASH WITH STERILIZATION
DISINFECT
INTEGRATED WITH THE MERITS
OF THREE KINDS OF WASHERS
+
SOAK
WASH
RINSE
N /DISINFECT
SPI
RINSE button
SOAK button
WASH button
SPIN/DISINFECT
Push the SPIN/DISINFCT
button to set the spin and
push it over 3 seconds to set
the disnfect procedure.
If you push it again,the
indicator will be off,then
you would cancel it.
During common and
carpeting programs, push
the SPIN/DISINFCT button
to set different spin time
(from 0 to 9 minutes)
During normal , cotton,
woollen and silk
Push the RINSE button to set the rinse
procedure.
Push the SOAK button
to set the soak procedure.
During standard and
Push the WASH button
to set the wash procedure.
During common and
carpeting programs, push the
WASH button to set different
wash time (from 0 to 25
minutes)
During common carpeting jeans programs,
push the RINSE button to set different
rinse times ( 0, 1, 2, 3, 4 times)
During normal , cotton woollen
and silk programs, push the RINSE
button to select rinse procedure, but
the rinse times can not be changed.
During save , posthaste programs,
push the RINSE button, the machine
have no reaction.
jeans programs, push the
SOAK button to set different
soak time (10,20,30 or 40
minutes)
During normal and cotton
programs, push the SOAK
button to select soak
During normal ,cotton woollen
and silk programs, push
the WASH button to
programs, push the
SPIN/DISINFCT button to
select spin procedure, but the
spin time can not be
changed.
During save , posthaste ,
programs, push
the SPIN/DISINFCT button,
the machine have
no reaction.
After you select to disinfect
clothes , the disinfector
will enter into inner tub
automatically only when
RINSE procedure is coming.
procedure, but the soak time
can not be changed.
select wash procedure,
but the wash time can
not be changed.
During common program, the machine
is set to save water program. If you
push the RINSE button before starting
operation, it will change to water
storage rinse program.
During save, posthaste,
woollen and silk programs,
push the SOAK button, the
machine have no reaction.
During save, posthaste
programs, push the WASH
button, the machine have
no reaction.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
Child lock function
Power On/Off button
This function is used to protect the children and prevent them from changing the
washing procedure.
button to switch on
s on, push it again
Push the POWER ON/OFF
the power. When the power i
to switch off the power.
Push and hold the WATER LEVEL button and SPIN/DISINFECT button, then push down the
POWER ON/OFF button. The digitron displays " " . You can continue setting desired
washing procedures. After setting, push down the START/PAUSE button. The child
lock function is activated.All of the buttons are locked and cannot make selection.
Release the child lock function: push down the WATER LEVEL and SPIN button at
the same time for more than 2 seconds. After a beep sound, the child lock function is released.
button to switch on
Push the POWER ON/OFF
the power. If the START/PAU
pushed, the washing machine
switch off the power after 5 m
SE button is not
will automatically
inutes.
Reserve/remain time indicator digitron
During sensing, it displays --
During reserve procedure, it displays the remained reserve time (in hour)
During operation of programs, it displays the remained time (minute). If the remained time exceeds 99 minutes,
it adopts A at tens place to represent 100 minutes, b to represent 110 minutes. For instance, A3 represents 103 minutes.
Page 16
In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16)
TIME REMAINED(MINUTES)
NORMAL
COTTON
WOOLLEN
COMMON
SAVE
POSTHASTE
CARPETING
RESERVE(HOURS LATER)
(18L)
MIN
SILK
HIGH GRADE CLOTHES
POWER
START
PAUSE
ON/OFF
PROGRAM
RESERVE
WATER LEVEL
Start/Pause
button
After the power is switched on, push it to
Start the machine
WA
TER
LEVEL
During working, push it to pause working.
During pause, push it to resume working.
button
RERSER
VE
button
The washing machine can detect the laundries automatically.
After detection, it will set the water level to suitable value
among 4, 6, 8,and 10 automatically.
In common operation mode,
the reserve indicator light
is off. The time remain
indicator light is on. The
digitron displays the time
remained (in minute)
PROGRAM
selectio
n butto
n
Following automatic programs are available for selection
You can also set water level by self. After the machine
is started, it will not set water level automatically. You shall
push the START/PAUSE button to make new setting.
If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .
Applicable situation
Common washing
Program
Common
Save
before the washing is
finished.
Quick and high-efficiency wash for
common laundries
If wet laundries are put in, it may display water level 10 . You
must set suitable water level by yourself.
Push down the RESERVE
button. The reserve
If POSTHASTE program is selected, it will display water
Posthaste
Carpeting
Super quick wash of the laundry
under 1 kg with light soil
indicator light is on ,The
digitron displays the reserve
time of finishing washing
(in hour).When the machine
is started, the reserve
indicator light is on,
level 3 . When water level
2
is reached in water filling, it will
perform washing while filling water. When water level
reached, it will change to normal washing.
3
is
Washing the relatively big and thick laundriesr
Washing the chimical fiber laundries
Washing the cotton textiles
During operation of wash and rinse program, you can push
down the water level button to add water. When you release
the button, or it reaches the overflow water level, the machine
will stop adding water except POSTHASTE. The water level
decided may be different from actual value because of the
different moisture level of the laundries.
Normal
Cotton
Woollen
Silk
Washing the woolen textiles
Washing the textile
indicating that the reserve
function is running.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
Steps of using the operation buttons and description of the steps
TIME REMAINED(MINUTE)
NORMAL
COTTON
WOOLLEN
COMMON
SAVE
MINUTES
MINUTES
MINUTES
TIMES
POSTHASTE
CARPETING
DOUBLE DRIVE WASH
RESERVE(HOURS LATER)
(18L)
MIN
SILK
DIGITAL TUBE DISPLAY
WASH WITH STERILIZATION
HIGH GRADE CLOTHES
DISINFECT
POWER
ON/OFF
INTEGRATED WITH THE MERITS
OF THREE KINDS OF WASHERS
START
PAUSE
+
SOAK
WASH
RINSE
/DISINFECT
PROGRAM
SPIN
RESERVE
WATER LEVEL
Push the "POWER ON/OFF " button to switch on the power.
POWER
ON/OFF
Push the "PROGRAM"button to select suitable automatic program.
2
PROGRAM
After switching on the power, the machine will set normal program automatically. To select other automatic
program, push the "program" button till the relative indicator is on. Refer to the "program button" on Page
11 for the selection.
For instance: select "POSTHASTE" program for laundries with small
quantity and light soil.
Page 11
In selecting the normal program, the machine
NORMAL
COTTON
WOOLLEN
COMMON
SAVE
will execute fuzzy program to select water
and wash time according to the cloth and weight
of the laundries. The full procedure is controlled
automatically.
POSTHASTE
CARPETING
SILK
HIGH GRADE CLOTHES
Push the "SOAK","WASH", "RINSE" or "SPIN/DISINFECT" button to select suitable procedure.
MINUTES
MINUTES
TIMES
MINUTES
H
WAS
RINSE SPIN/DISINFECT
SOAK
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
After switching on the power, the washing machine will set to common program including"wash, rinse,
spin "automatically.To select other procedures, push the "SOAK"," WASH"," RINSE"or "SPIN/DISINFECT"
button to select the time of soak,wash and spin, and the times of rinse. After switching on the power,
if you push one of the button among "WASH", "RINSE"and"SPIN/DISINFECT", the digitron of the former
procedures will turn off automatically. The former procedures will not run. For instance: after switching
on the power. If you push the "SPIN" button first, it will execute spin singly after starting.
Attention
.
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
The pulsator will not rotate unless the water is
filled to water level 3.
After the machine starts operation, you can only set the program and procedure during washing, and can not
make setting in other cases.
The soak program can be used as fitting of common, carpeting,nomarl or cotton automatic programs. It will do soaking
with intermittent stirring of pulsator.
When you select to disinfect clothes. You select to use softener too. If you don't select to disinfect,please put don't in softener.
Press " WATER LEVEL "button,
select suitable water level
WATER LEVEL
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "START/PAUSE"
button, then push the "WATER LEVEL" button to set the water level. Refer to "water level, water quantity and
desoge of powder"in Page 9 and "WATER LEVEL"button in Page 11 for selection.
Page 11
Page 9
Water Level and Time Table for Each Program (self programming not included)
Water
Total time(minutes)
Wash(minutes)
Rinse(minutes)
Spin(minutes)
About 5
Program
level
1~10
1~10
3
Common
Save
About 9-11
About
Rinse twice, about 3 each time
About 34-36
About 20
About 6
Saving water program, total about 10 minutes
Saving water program, total about 4 minutes
About 2
About 20
Posthaste
Carpeting
Normal
Cotton
1~10
1~10
1~10
1~10
1~10
Rinse twice, about 5 each time
About 7
About 54
About 25-29
About 48
About 25
About 30
About 10-14 Saving water program, total about 13 minutes
Rinse three times, about 3 each time
About 10
About 3
About 5
About 5
About 3
About 4
Rinse twice, about 2 each time
Rinse twice, about 2 each time
Woollen
Silk
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
* Total time: including the normal water inlet time and drain time. The total washing time may be influenced by
the water inlet pressure and water level.
* Spin time: From the moment the intermittent spinning starts to the moment it stops running (the time displayed
on spin digitron is from intermittent spinning to the moment before inertia spinning; the time displayed on the
time remain digitron is the total remained time)
* In selecting "posthaste" program, the washing machine will set the complete procedures of water level
selectior, washing, rinsing and spinning automatically.
* During saving water program, if the water inlet pressure is lower, the machine will come into rinse with water .
* When selecting soak procedure, it will first soak for 10~40 minutes , then do washing , rinsing and spinning .
Push the "reserve" button to select suitable reserve wash program
RESERVE
After switching on the power, the reserve program is set to off mode automatically. If you need to set the washing
procedure to be finished at reserved time, please push the " RESERVE " button to set the reserve wash program.
Refer to RESERVE button in Page 11 for selection.
Page
Confirm the operation of reserve program
TIME REMAINED(MINUTE)
When the "reserve" function is activated, the indicator light of the program you have set
will be off. The remained time will be displayed. During reserve procedure, push the
RESERVE(HOURS LATER)
"RESERVE" button to display the reserve mode.
To change the running program or cancel the reserve setting, you
the washing will be finished after 18 hours.
need to switch off the power and make new selection.
Push the "START/PAUSE" button
START
PAUSE
5 Close the top lid
As the top lid opened ,the Washer will automatically give an alarm
and stop running , exclusively during supplying water and rinsing.
6 Finish washing
After finishing wash it'll switch off the power automatically.
After Finishing wash
alarm automatically
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence
Using process
your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Clean the detergent box and set it on
the control panel seat.
1.The method of dismantle : Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
The lint filter must be used during washing.
It must be cleaned in time after each using
Lint filter:
1.Pull it up to dismantle.
2.Push it down to install.
3.Clean the filter screen after washing.
Dismantle
Install
Dismantle
Dismantle
Install
Install
Clean
Dismantle and install
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Please clean it with brush every two months.
Do not wipe it with thinner, petrol, alcohol etc.
Benzene
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (
about 1 hour), then close the top lid.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
Phenomena
The reason
How to settle
Close the top lid.
The top lid is opened during reserve
procedure.
The digitron displays E0.
Put down the drain hose. Open and close the
top lid once.
The drainage cannot work, or is too slow.
The digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
Clean the foreign material. Open and close
The top Lid Once.
It stops running in midway. The digitron
displays E2.
Close the top lid.
The top lid is not closed.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
Open the water tap. Open and close
the top lid once.
Clean the water inlet valve then open
and close the top lid once.
Open and close the top lid once.
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
The water filling does not work, or is
slow. After about 15 minutes later,
the digital displays E4.
Please contact the after-sales
service department.
The water level sensor is bad.
The digitron displays E6.
The power voltage is too low.
The power voltage is too high.
The digitron displays E8.
The digitron displays E9.
Not wash
Pull off the power plug. Wait for the
voltage resuming normal before usage.
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
The machine does
not act
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Not spin
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
There's abnormal sound
inside the machine
Is the screw of the jointer of water
inlet hose loose or awry?
The water tap leaks
Fasten the screw of the jointer properly.
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure pauses.
The cloth sensor is detecting , it will add water
after about 48 senconds.
The program is setting the drain time , certain
period is needed before it starts spinning.
Select spin program, but it does not work.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained performance inspection
by the factory.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing list
One
Inside the accessory bag
Inside the accessory bag
Components of the water inlet hose
Tapping screws
Eight
Inner cover component
Bottom plate
Between the upper cushion of the
washing machine package and the
upper seal of the package carton
One
One
Computerized Automatic
washing machine
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification table
Model
HWM90-98
Rated voltage frequency
Rated washing / spinning capacity
Water level/Water quantity (about)
220V-240V ~ 50Hz
9.0kg
1/18L 2/24L 3/30L 4/36L 5/42L 6/48L
7/54L 8/60L 9/66L 10/68L
About 120L (Highest water level; Normal program)
0.03MPa~0.78MPa
Max water consumption
Water Injection pressure
Rated washing input power
Rated spinning input power
Weight
380W
300W
About 39kg
Overall dimension
L 610 mm W 580mm H 975 mm
Download from Www.Somanuals.com. All Manuals Search And Download.
|