Double drive Washing Machine
User's manual
This manual is for
HWM90-0566
Please read this manual carefully
before using.
Retain it for future reference.
0030507805A
W
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing list
Names of the parts
Quantity
Name
One
User's manual
Water inlet valve
Top lid component
Control panel
Component of the
water inlet hose
Water absorption
cushion
The end connecting to
the washing machine
Filter cover
One
Detergent box
Handle
Jointer connecting the
water inlet hose and
the water faucet
Balance ring
Power cord
Back cover
Drain hose
Lint filter(two)
Inner tub
The end connecting to the
water inlet hose jointer
Pulsator
Adjustable leg
film
One
Adjustable leg
Front control board
Cabinet
Bottom cover
(Inside the inner tub of washing machine)
Drain hose frame
Fixed leg (3 pieces)
Topping screws
Eight
One
Inner cover
component
Meaning and description of the symbols
Warning sign
Full automatic washing machine
One
Contents marked with that symbol are related to the
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.
Specification
Contents marked with that symbol are actions forbidden
to perform. Performing of those action may result in
damage of the machine or influence the personal safety of
the users.
Forbidden sign
Water level/Water
quantity (about)
1/23L 2/29L 3/35L 4/39L 5/45L
6/50L 7/55L 8/60L 9/65L 10/70L
Water Injection pressure
0.03MPa 0.78MPa
~
Rated washing /
spinning capacity
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble-shooting Answer to question
Safety precautions
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.
Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department
or after-sale service department of our company. Do not repair it by yourself.
The washing machine must be positioned
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
so that the plug is accessible. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
c l e a n i n g t h e m a c h i n e . D o n o t p l u g
or pull the power plug with wet hand.
Phenomena
The reason
How to settle
The digitron displays E0.
The top lid is opened during reserve procedure.
Close the top lid.
Put down the drain hose. Open and close the
top lid once.
Clean the foreign material. Open and close the
top lid once.
The drainage cannot work, or is too slow.
The digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
It stops running in midway. The digitron
displays E2.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or the after-sale service department.
The top lid is not closed.
Close the top lid.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
Reorder the laundries. Close the top lid.
Th machine will start running after 10
seconds of being placed horizontally.
Are the laundries put slantingly?
Is the machine slanting?
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the start/Pause button once.
Push the Start/Pause button once.
The water filling does not work, or is
slow. After about 30 minutes later,
the digital displays E4.
In case the washing machine is installed on ground
with carpet, do not block the ventilation hole with
carpet.
Do not use water hotter than 50
.
Please contact the after-sales
service department.
The digitron displays E6.
The water level sensor is bad.
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
The ventilation
holes at the bottom
Not wash
The machine does
not act
Back
Soft object
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Front
Not spin
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
There's abnormal sound
inside the machine
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Is the screw of the jointer of water
inlet hose loose or awry?
Fasten the screw of the jointer properly.
The water tap leaks
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure is paused.
The cloth sensor is checking the cloth, it will add water after 48 seconds.
The program is setting the drain time. Some time is needed
before it starts spinning.
Push the PROGRAM button to select SPIN,
but it doesn't work.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
The pulsator pauses during water inlet
in wash and rinse.
It is to avoid splashing during water inlet.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained in the factory inspection of performance.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Disposal after washing
Safety precautions
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Do not put hand into the rotating tub. It is dangerous
Do not decompose, repair or alter the machine by
yourself.
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
The lint filter must be used during washing.
Clean the detergent box and set it on
It must be cleaned in time after each using.
the control panel seat.
Lint filter:
1.Push down the spring piece of the top lint filter
1.The method of dismantle: Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
to make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can
get down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it
tight .
trol
Pe
Benzene
6.Make sure the lint filter well installed, or it can
influence your use.
Up
The back cover of lint filter
Up
Install
Dismantle
Dismantle
Install
Dismantle
Install
Down
The front cover of lint filter
Figure 2
The handicapped or children without care shall not use
the machine.
Down
Keep the machine away from direct sunlight and
heat source like the heater.
Figure 1
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
Wipe it with neutral detergent.
Please clean it with brush every two months.
Do not wipe it with thinner, petrol, alcohol etc.
Benzene
Please keep the lint filter in good condition,
and install it to proper position during
washing. If the lint filter is lost or
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
Install
Dismantle
damaged, please contact the customer
care agent of our company.
.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
To change the direction of drain pipe, please contact the customer care agent of our company.
4.Hang up the power cord and drain hose.
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,
please be sure to ensure the washer is placed under the room temperature for 24 hours and then use
otherwise the washing effects may be lowered or the washer may be damaged.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Attention
.
Even there's no water in the tub, a certain period is
required before spin starting.
Install the Inner cover component
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
Before initial use of the machine, assemble the inner cover as described below:
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming
the inner cover shaft to the installation hole of the
corresponding outer tub cover shaft groove.
The pulsator will not rotate unless the water is
filled to"3" water level.
Outer tub cover
Outer tub cover shaft groove
The soak procedure can work in cooperation with automatic programs like normal, jeans, fiber and cotton.
There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing, and can not
make setting in other cases.
Inner cover shaft
Inner cover
3.Firstly insert the inner cover shaft of one side into the
corresponding outer tub cover shaft groove, then push
the another inner cover shaft into the corresponding
outer tub cover shaft groove. Please install to designated
position to guarantee there are no dropping or abnormal
sound in opening and closing of the inner cover, and the
operation shall be smooth. Do not dismount the inner cover
component after washing.
Damping cushion
Water level
4 Push the " water level" button, select suitable water level
Push
Section I enlarging
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"
button, then push the "water level" button to set the water level.
Install the bottom plate
After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of
the machine, then lift the machine up
gently. See to the figure:
5 Push the "reserve" button to select suitable reserve wash program
I
Back
After switching on the power, the reserve program is set to off mode automatically. If you need to
set the washing procedure to be finished at reserved time, please push the " reserve " button to
set the reserve wash program. Refer to reserve button in Page 10 for selection.
Front
Bottom plate
Soft items
Two claws at the bottom cover shall
be inserted in two bar-shaped holes
in the stand. Make sure the claws
are firmly in place.
Section I enlarging
Confirm the operation of reserve program
To change the running program or cancel the reserve setting, you
need to switch off the power and make new selection.
Adjust the Installation position
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground
will result in unstable running or stoppage of the machine. Please adjust it with following methods:
6 Push the "Start/Pause" button
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
6 Finish washing
5 Close the top lid
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
As the top lid opened, the washer will automatically
given alarm and stop running, exclusively during
draining
After finishing wash it'll
alarm automatically
the adjustable nut
Fasten
Loosen
2 . After adjustment, fasten the nut.
the adjustable feet
High
Low
Download from Www.Somanuals.com. All Manuals Search And Download.
How to change the direction of the drain hose
Steps of using the operation buttons and
description of the steps
b
1.Dismantle the rear cover of the washing machine.
3.Dismantle the drain outlet protecting cover at the other side,
(the way is the same as the drain bushing),then install the drain
bushing, as indicated in Figure 4.
Standard
•
•
•
•
••
Normal
Tub dry
2.Put down the drain hose Take off the drain hose
frame as indicated in Figure 1.Take the drain hose into
the cabinet then nip the drain fixing clamp to make
it deviated from the clip the other hand is used to put
down the drain bushing as indicated in Figure 2 3.
Fibre
Quick
•
•
•
•
Cotton
Posthhaste
Jean
Woollen
4.Extend the drain hose from the other side. Fix the drain hose
with drain hose frame onto the cabinet, as indicated in Figure 5.
drain outlet protecting
cover
Reserve
Spin
6
Drain hose
Figure 5
Figure 4
5
Drain hose support
Cabinet
Inner
Drain bushing
Figure 2
Drain bushing
Figure 1
5.Install the drain outlet protecting cover to the other side,
as indicated in Figure 6
Outer
Push
Drain bushing
1.Push "power" button to switch on the power
Take do
wn
Drain hose fixing
clamp
Figure 6
Push
Figure 3
2.Push "program" button to select suitable
full-auto program
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose
with our company serviceman .
After the power is switched on, "normal"is automatically set. To select other full-auto program, please
push the "program" button till the corresponding indicator is on. Refer to the "Program button" on Page 11.
E.g. Set to "Quick wash" program for small quantity of laundries with light soil.
Usage the drain hose
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than 10cm,
or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.
4.If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
Push the "SOAK", "WASH", "RINSE" OR "SPIN" button to select suitable procedure.
2.Do not step on or press the drain hose.
Spin
3. If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
5.If the extra hose is too long, cut it either at A or at B.
After switching on the power, the washing machine will set to common program including"wash, rinse,
spin "automatically. To select other procedures, push the "SOAK", " WASH", " RINSE" or "SPIN"
button to select the time of soak, wash and spin, and the times of rinse. After switching on the power,
if you push one of the button among "WASH", "RINSE"and"SPIN", the digitron of the former
procedures will turn off automatically. The former procedures will not run. For instance: after switching
on the power. If you push the "SPIN"button first, it will execute spin singly after starting.
5
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the water inlet hose
Reserve, remain time digitron
Confirm the water faucet
It displays "--" during detecting.
It displays remained reserve time (hour).
It displays total remained time (min). If the total time
exceeds 99 minutes, it uses "A" on tens digit to
represent100 minutes, and uses "b" to represent 110
minutes. E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation.
(See to Page15)
"Power" button
Water faucet,suitable
Water faucet,not suitable
Push the "power" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "power" button to switch on the power. If
the "start/pause" button is not pushed, the machine
will switch off the power automatically after 5 minutes.
Outlet end surface
>10mm
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
••
•
Standard
Fibre
•
•
•
•
•
Tub dry
Normal
Quick
Connection between the water inlet hose jointer and the water faucet
•
Posthaste
Cotton
Woollen
TUB DRY button
•
Jean
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
•
Push the"TUB DRY"button,the
indicator is lighted,and the"TUB DRY"
function is operating. the"TUB DRY"
can not be selected after the
"program" button have been selected.
After washing,the innerand outer
tub is wet,mildew may grow not
using for a long time.Then,the
"TUB DRY" fuction can make the
tub dry preventing mildew from
growing.
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
Reserve
water inlet hose jointer
Screw
Slider
Sign plate
Screw knife
Bushing
Lock level
water inlet hose
Figure 1
Figure 2
Figure 3
selection button
PROGRAM
WATE
R LEVEL
button
3.Fasten the four screws evenly. See to Figure 4.
The washing machine can detect the laundries automatically.
After detection, it will set the water level to suitable value among 4, 6, 8,
and 10 automatically.
You can also set water level by yourself. After the machine is started, it
will not set water level automatically. You shall push the start/pause
button to make new setting.
If there's water inside the tub, the machine cannot detect the laundries
and will display water level 6 .
If wet laundries are put in, it may display water level 10 . You must set
suitable water level by yourself.
If POSTHASTE programs selected, it will display water level 3 .
When water level 2 is reached in water filling, it will perform washing
while filling water. When water level 3 is reached, it will change to
normal washing.
During operation of wash and rinse program, you can push down the
water level button to add water. When you release the button, or it
reaches the overflow water level, the machine will stop adding water.
The water level decided may be different from actual value because of
the different moisture level of the laundries.
Following automatic programs are available for selection
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Applicable situation
PROGRAM
STANDARD
QUICK
"Reserve" button
Common washing
Quick and high-efficiency wash for common
laundries
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
The digitron displays remain time
before washing is finished (in minutes)
Push "reserve" button, the digitron
displays the reserve time of washing
(in hours). The indicator flashes to
indicate that the reserve function
is operating.Push "reserve" button to
displaythe reserve mode.
Super quick wash of the laundry under 1 kg
with light soil
POSTHASTE
JEAN
Washing the relatively big and thick laundries
Washing the chemical fiber laundries
Washing the cotton textiles
About 4mm before twisting
About less than 2mm after twisting
FIBER
COTTON
WOOLLEN
NORMAL
Screw nut
Washing the woolen textiles
Figure 6
Figure 4
Common washing
Figure 5
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Use the operation buttons
Connection between the water inlet hose and the washer
a Description of the function of buttons
CHILD LOCK FUNCTION
1.Do not take off the water absorption cushion. Please check if the
nut of the water
cushion is dropped or damaged before each usage. If it happens
inlet hose
Push and hold the WATER LEVEL button and SPIN button,
Indicator mode and meaning
then push down the POWER ON/OFF button. The digitron
displays CL . You can continue setting desired washing
procedures. After setting, push downthe START/PAUSE button.
The child lock function isactivated. All of the buttons are locked
and cannot make selection.
please contact our after-sale department immediately.
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
Flashing, indicating the running program
On, indicating the program about to run or the selection mode
jointer of the
water inlet valve
water absorption
cushion.
Release the child lock function: push down the WATER LEVEL and
SPIN button at the same time for more than 1 second. After a beep
sound, the child lock function is released.
"Start/pause" button
After the poweris switched on, press it to
start the machine
During working, pushit to pause.
During pause, pushthis button torestart
and go onworking
Connection between the jointer of the water inlet hose and the water inlet hose
Spin
Soak
Wash
Rinse
••
the jointer of the
water inlet hose
1.Push down the slider. Insert the water inlet hose into the jointer.
Slider
Locking level
Over flow
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
Wash
Spin
Check the connection between the jointer of the water inlet hose
and the water faucet
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
WASH button
SOAK button
RINSE button
SPIN button
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
Push the WASH button to set
the wash procedure.
Push the SOAK button to set
the soak procedure.
Push the RINSE button to set the rinse
and disinfect procedure.
Push the SPIN button to set
the spin procedure.
During STANDARD
During STANDARD NORMAL
and JEAN programs, push the
SOAK button to set different
soak time (10,20,30 minutes)
During FIBER and
During STANDARD NORMAL and
JEAN programs, push the RINSE
button to set different rinse times ( 0, 1,
2, 3, 4times).
During STANDARD NORMA
NORMAL and JEAN
programs, push the wash
button to set different wash time
(6,9,12,15 minutes)
L
and JEAN programs,
push the SPIN button to set
different spin time (
While the "Overflow" digitron is
lighting,the program of the overflow
rinse has been selected.
During FIBER
,
COTTON
,
During FIBER
,
COTTON
COTTON programs, push
the soak button to select soak
procedure, but the soak time
cannot change.
WOOLLEN and SILK
Dismantle the water inlet hose
WOOLLEN programs, push
the WASH button to select
wash procedure, but the wash
time cannot change.
programs, push the SPIN
During FIBER
,
COTTON
,
button to select spin procedure,
but the spin time cannot change.
1. Close the water faucet.
WOOLLEN programs, push the
RINSE button to select rinse procedure,
but the rinse times cannot change.
During QUICK POSTHASTE
WOOLLEN TUB DRY , and
SILK programs, push the
SOAK button, the machine
have no reaction.
,
During QUICK
,
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
During QUICK TUB DRY
POSTHASTE , programs,
push the SPIN button, the
machine have no reaction.
,
POSTHASTE , programs,
During QUICK
,
POSTHASTE TUB
Locking level
push the wash button the
machine have no reaction.
DRY programs, push the RINSE button,
the machine have no reaction.
If the machine is used frequently, the jointer of the water inlet hose can be
kept on the faucet to prevent damaging the fixing screw.
Slider
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Preparation before washing
2.Put in the laundries
The capacity of washing of the machine refer to the largest weight of the
standard laundries under dry condition that can be washed in one
time. Laundries quantity in one washing cycle shall be lower than
the rated capacity. The largest capacity of this machine is 9.0 kg.
Preparation before washing
1.Connect the water inlet hose
2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose
The thickness ,size , type of the cloth will influence the actual washing capacity.
It is suitable to put in reasonable amount of laundries and the laundries can be
turned round in washing for one time washing.
Do not select " 4" water level for laundries less than 1.0kg ,so as to avoid
splashing of water.
3. Usage of the detergent
Add washing powder and softener into
the box directly as per indicated in left figure
4.slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally
Control panel seat
After adding, close the box.
Softener inlet
Liquid detergent
inlet
Washing powder inlet
Washing powder box
Pay attention to followings before washing the laundries
The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
Confirm if there's
special requirement
for the laundries.
Clear the pocket.
Take out the coins ,
sand, hairpins etc.
Fasten the buttons
and zippers.
How to use washing powder
How to use softener
See to the manual of softener for the usage and dosage.
When adding softener into the softener inlet of washing
powder box, note that it shall not exceed the lower side
of the cap.
Do not leave the softener for long period after adding it
into the box. Otherwise it may be solidified and block the inlet.
As the softener is easy to solidify, please clean the box
frequently.(You shall clean it each time you use reserve
function).
It is suggested to add washing powder into the box
directly under fuzzy program and reserve program.
Dissolve directly inside the washing machine: (not
applicable for fuzzy and reserve program)
1.Add some water
laundries.
2.Add washing powder. Run for about 30s to fully dissolve
Powder. Then push the"start/pause" button.
the
3.Put in laundries. Select suitable water level. Push the
Button again.
"start/pause"
Before use softener, you must select to sterilize function
Quick dissolving of washing powder:
1. Prepare warm water of 30 C and container.
2. Add washing powder while stirring to dissolve it
completely.
How to use whitener
Please add suitable washing powder as per the laundries
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
g.For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into
mesh bag for washing.
quantity, the set water level and water quantity.
Add water to stipulated level. Dilute the whitener with container,
and then pour it into the liquid whitener inlet slowly.
If you select quick wash program, it is suggested to use
liquid detergent instead of washing powder to guarantee
Laundries with color or pattern is not colorfast, thus not applicable.
the washing effect.
It is not recommended to use rich-foam washing powder.
The whitener shall not touch laundries directly.
See to the manual of whitener for the usage and dosage.
For whitener in powder, dissolve it before use.
Washing powder with poor quality or long-time storage may
get caked. Please clean the detergent box duly in usage.
Download from Www.Somanuals.com. All Manuals Search And Download.
|