Quick Reference
Service Manual
HP DesignJet 2500CP
HP DesignJet 2000CP
Printers
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Which Firmware relates to which Ink system?
A.01.XX Ć This firmware revision means that the Printer can only use Imaging Inks.
A.02.XX Ć This firmware revision means that the Printer can use both the Imaging Inks and
the new UV Durable Inks.
UsetheLatest Firmware/ PostScript Revision
Always check which firmware revision the printer is using (Utilities / Statistics / Code Rev)
and ifnecessary, update it. Also check the PostScript revision (Utilities / Statistics / PostScript
Rev) and ifnecessary, update it.
Install theFirmwareSIMM and PostScript SIMM in thecorrect slots
Remember that the Firmware SIMM (including the firmware code for the imaging and UV
Durable Inks) must installed in the first slot from the left. The PostScript SIMM must be
installed in the second slot from the left.
Perform a Service Test on the Failed Component/Assembly
Always perform a Service Test on the component/assembly that you are about to replace, just
to make sure that is the component/assembly that has failed. If thetest on that
component/assembly passes, do NOT replace it.
Solving ImageQuality Problems
Whenever an Image Quality problem appears, print the Image Quality Print to help diagnose the
problem. The Image Quality Print will help you differentiate between possible IDS / Printer /
media errors and other problems such as incorrect frontĆpanel selection, driver or RIP
configuration or mechanical problems. For information on solving Image Quality problems '
Users Guide.
Line Sensor has Problems Detecting Media
Clean the driveĆroller. Replace the lens cover ' Users Guide, Chapter 10 (Lens Maintenance).
Perform the Line Sensor calibration. Reinstall or, if necessary, replace the Line Sensor.
Carriageis Noisy
Clean and apply lubricant to the Carriage slider rods. Perform Carriage Axis Test.
Service Station is Noisy
Clean and apply lubricant to the Service Station slider rod. Perform Service Station Test.
Printer continuously rejects Printheads
Clean Printhead and Carriage flex contacts. Remove all Printheads from the Carriage and try
installing just the rejected Printhead. Ifthe Printhead is still rejected then replace the
Printhead with a new one. Ifthe new Printhead is not rejected then check, one by one, ifthe
other Printheads are also rejected. Perform the Printhead Continuity Test. Perform the
Electronics Test. Replace the Trailing Cable. Replace the Carriage Assembly.
Bail Assembly does not lower all the way
Check that there are no obstructions in the way ofthe Bail Assembly. Perform the Bail Test.
Cover Sensors aren't Working
Check if the faulty sensor is installed correctly. Check if the cable for the faulty sensor is
connected correctly. Replace the faulty Sensor.
HP DesignJet 2500CP and 2000CP Printers
Quick Reference Service Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Media continuously crashes
Check if the media loaded is HP approved. If the media is not HP approved, advise the
customer to use HP media and check to see if the problem is now solved. Perform the Refill
Calibration and try to load the media again. Replace the Overdrive Assembly. Remove the
Drive Roller and install in the correct position.
Switch Power Off / Check Printhead Path" message appears when the Printer is
about to cut or is cutting?
Check the media path and clear it if necessary. Perform the Cutter Test. Replace the Cutter
Assembly. Replace the Overdrive Assembly.
Lens Maintenance" message appears on the FrontĆPanel?
The lens cover, which is installed on the line sensor, is dirty. Clean the Mark Encoder on the
Driver Roller. Replace the lens cover ' Users Guide, Chapter 10 (Lens Maintenance).
Printer does not Power ON
Check that the power cord is connected correctly. Check that the Flash SIMM is installed
correctly in the correct slot (the first slot from the left) at the back of the Printer. Try to
disconnect all the cables, apart from the Front Panel Cable, from the Electronics Module and
then try to power ON the Printer again. If nothing appears on the frontĆpanel display, then
replace the Electronics Module. If the Printer does Power On with the cables disconnected,
then the problem must be with another component of the Printer. To find the faulty
component, power OFF the Printer and connect one of the cables and power ON again. Once
the faulty component is connected, it will not allow the Printer to power ON. This component
should then be replaced.
Printer has problems with Media Loading
Check that the Media Sensor is installed correctly. Check if the cable for the Media Sensor is
connected correctly. Check if the Pincharms are down (the Pincharm lever should be up).
Make sure Line Sensor is installed correctly. If necessary, replace Line Sensor. Replace Media
Sensor. Perform Electronics Test.
System Error Codes
WARNING:
Only replace one component at a time and check if the error has gone
before replacing another component. Using this procedure you will be
able to determine exactly which component failed.
System Error:
System Error:
System Error:
0000D8 Ć Refer to System Error Code 07xxxx.
010020 Ć Reseat/replace Flash SIMM. Replace Electronics Module.
010021 AXXXXXXX
NOTE:
Printer will not function without any RAM SIMMs installed. Install a
minimum of 4MB memory module.
D
If Error Data is higher than A4000000, check RAM SIMMs are original HP supported
parts. If more than one RAM SIMM is installed, remove one of them and power on the
printer again. If system error reappears, reinstall the removed RAM SIMM and remove the
other RAM SIMM and then power on the printer again. If system error reappears then try
replacing both RAM SIMMs with new ones.
D
If Error Data is lower than A4000000, replace Electronics Module.
HP DesignJet 2500CP and 2000CP Printers
2
Quick Reference Service Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
System Error:
System Error:
010022 Ć Replace Electronics Module.
010023 Ć Check XĆencoder and optical sensors (media, pinchĆwheel, refill,
elevator, primer and service station) cable path for damage. Replace Electronics Module.
System Error:
System Error:
010025 Ć Replace Electronics Module.
010030 Ć Check Refill/Service Station Interconnect Cables. Replace
Refill Interconnect PCA. Replace Service Station Assembly. Replace Electronics Module.
System Error:
010031 Ć Check/replace Trailing Cable. Perform Carriage Calibration.
Replace Carriage Assembly. Replace Electronics Module.
System Error:
010032 000000XX
Error data (XX):
1 ³ Electronics Module fan failed.
2 ³ Service station fan failed.
3 ³ Both fans failed.
10 ³ Electronics Module fan is shortĆcircuited.
20 ³ Service Station fan is shortĆcircuited.
30 ³ Both fans areshortĆcircuited.
12 ³ ServiceStation fan is not running and theElectronics Modulefan is shortĆcircuited.
21 ³ Electronics Modulefan is not running and theServiceStation fan is shortĆcircuited.
Try the following: Check the Service Station fan is connected correctly. If both fans fail,
replace Electronics Module. If Service Station fan is faulty, check Service Station
Interconnect Cable. Replace Service Station Assembly. Replace Electronics Module.
System Error:
010033 Ć Replace Electronics Module.
System Error:
010034 000X0000
Error data:
00010000 ³ XĆaxis Motor Failed.
00020000 ³ YĆaxis Motor Failed.
00030000 ³ Both DC Motors Failed.
Try thefollowing:
D
D
Check that both DC Motors are connected correctly.
If Faulty YĆaxis motor:
S
Check Refill Interconnect Cable. Replace Refill Interconnect PCA. Replace YĆaxis
Motor Assembly.
D
D
If Faulty XĆaxis Motor Ć Replace XĆaxis Motor Assembly .
If both DC Motors fail, replace Electronics Module.
HP DesignJet 2500CP and 2000CP Printers
Quick Reference Service Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
System Error:
010035 0XABCDEF
Error data (0XABCDEF):
If the value of each letter is 0, then the component is OK. If the value of each letter is 1 then
the component has failed.
X ³ Electronics signal failed (ignore other values).
A ³ Elevator Stepper Motor Failed.
B ³ Refill Stepper Motor Failed.
C ³ Primer Stepper Motor Failed.
D ³ Service station (ZĆaxis) Stepper Motor Failed.
E ³ Service station (XĆaxis) Stepper Motor Failed.
F ³ Bail Stepper Motor Failed.
Try the following:
D
D
D
D
If X = 1 then replace the Electronics Module.
Check the Interconnect Cables.
Check the failed Stepper Motor is connected correctly.
If Bail, Elevator or the Refill Stepper Motors are faulty, then:
S
Replace Refill interconnect cable. Replace Refill interconnect PCA.
D
If Faulty Primer or Service Station Stepper Motors Ć Replace Service Station
Interconnect cable.
D
D
D
D
D
D
If Faulty Elevator Stepper Motor Ć Replace Elevator Assembly.
If Faulty Refill Stepper Motor Ć Replace Refill Assembly.
If Faulty Primer Stepper Motor Ć Replace Primer Assembly.
If Faulty Service Station Stepper Motors Ć Replace Service Station Assembly.
If Faulty Bail Stepper Motor Ć Replace Bail Stepper Motor Assembly.
Replace Electronics Module.
System Error:
010036 - Switch the Printer OFF from the back and then disconnect the
Trailing Cable from the Electronics Module. Switch the Printer ON and see if the Error Code
now changes to 010037". If the error code remains as 010036", replace the Electronics
Module. If the Error Code changes to 010037" then refer to that error code.
System Error:
System Error:
System Error:
010036 00000800 - Problem with the YĆaxis or ANY Stepper Motor.
010036 00001000 - Problem with the XĆaxis or ANY Stepper Motor.
010037 Ć Check/replace Trailing Cable. Replace Carriage Assembly.
Replace Electronics Module.
System Error:
System Error:
System Error:
010038 Ć Refer to error code 010037".
010039 Ć Check/replace Trailing Cable. Replace Carriage Assembly.
010040 Ć
Refer to error code 010037".
HP DesignJet 2500CP and 2000CP Printers
4
Quick Reference Service Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
System Error: 010041 Ć Switch thePrinter OFF and ON again. During initialization
another error code will appear. Refer to the relevant error code for further information.
System Error:
010042 0000000X
Error data (X):
0 ³ Faulty Media Sensor.
1 ³ Faulty PinchĆarm Sensor.
2 ³ Faulty Refill Assembly Sensor.
3 ³ Faulty Elevator Sensor.
4 ³ Faulty Service Station Sensor.
5 ³ Faulty Primer Sensor.
Try thefollowing:
D
D
Make sure that all sensors are connected correctly.
If Faulty Service Station or Primer sensors Ć Check/replace Service Station Interconnect
Cable.
D
D
D
D
D
D
D
D
If Faulty Refill Assembly or Elevator sensors Ć Check/replace Refill Interconnect Cable.
If Faulty PinchĆarm sensor Ć Replace PinchĆarm Sensor.
If Faulty Refill Assembly Sensor Ć Replace Refill Assembly.
If Faulty Elevator Sensor Ć Replace the Elevator Assembly.
If Faulty Service Station Sensor Ć Replace the Service Station Assembly.
If Faulty Media Sensor Ć Replace Media Sensor.
If Faulty Primer Sensor Ć Replace Primer Assembly.
Replace Electronics Module.
System Error:
System Error:
System Error:
System Error:
010100 Ć Replace Electronics Module.
010101 Ć Refer to Error Code 07xxxx
010102 Ć Replace Electronics Module.
010110 Ć Test Electronics Module. Perform the following Calibrations:
Carriage / Refill / Line Sensor / Service Station / Printhead Alignment / Color Calibration /
ServiceAccuracy. Makesureyou havethelatest version of theFlash SIMM (firmware)
installed. Replace Electronics Module.
System Error:
010111 Ć Press ENTER and reĆconfigure the front panel settings. If
possible, enter Service Mode and clear the EEROM. If error code continues, replace
Electronics Module.
System Error:
010120 Ć If Error Code appeared during normal operation and not during
initialization, then problem can be solved by switching the printer OFF and ON again. Enter
in Service Mode. During initialization Error Code 010110" appears. Refer to that error code
for further information.
System Error: 010121 Ć Switch the printer OFF and ON again. If Error Code reappears,
replace Electronics Module.
HP DesignJet 2500CP and 2000CP Printers
Quick Reference Service Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
System Error:
020000 Ć Check the Service Station Interconnect Cable. Check cables for
the Primer Stepper Motor and Sensor. Check that the air tubes that are connected between
the primer assembly and the service station are in the correct position and are not squeezed
together. Check that the Primer Stepper Motor is NOT shorted. Replace Service Station
interconnect cable. Replace Primer Assembly. Replace Service Station Assembly. Replace
Electronics Module.
System Error:
020001 Ć Check if the ink cartridges are installed correctly on the
Elevator and that there are no obstacles in the way. Check/replace the Refill Interconnect
Cable. Check cables for the Elevator Stepper Motor and Sensor. Check that the Elevator
Stepper Motor is NOT shorted. Replace Refill Interconnect PCA. Replace Elevator Assembly.
Replace Electronics Module.
System Error:
020002 Ć Check/replace Refill Interconnect Cable. Check Refill Stepper
Motor and Sensor cables. Check that the Refill stepper motor is NOT shorted. Replace Refill
Interconnect PCA. Replace Refill Assembly. Replace Electronics Module.
System Error:
020003 Ć Perform the Refill Calibration. Check for obstacles in the Refill
path. Check/replace Refill Interconnect Cable. Check the cables for the Refill Stepper Motor
and Sensor. Check that the Refill stepper motor is NOT shorted. Replace Refill Interconnect
PCA. Replace Refill Assembly. Replace Electronics Module.
System Error:
020004 Ć Perform the Service Station Calibration. Check that the Service
Station flag is installed correctly. Check that the Service Station nut is installed correctly. The
nut is located on the front side of the Service Station, just below the Printhead Cleaner
holder. Check/replace the Service Station Interconnect Cable. Check cables for the Service
Station components. Check that the Service Station stepper motors are NOT shorted.
Replace Service Station Assembly. Replace Electronics Module.
System Error:
020005 Ć Check if the ink cartridges are installed correctly on the
Elevator and that there are no obstacles in the way. Check/replace Refill Interconnect Cable.
Check cables for the Elevator Stepper Motor and Sensor. Check that the Elevator stepper
motor is NOT shorted. Replace Refill Interconnect PCA. Replace Elevator Assembly. Replace
Electronics Module.
System Error:
System Error:
codedisappears. If theerror codedisappears,
020006 Ć Perform Refill Calibration.
020010 Ć Switch the printer OFF and ON again and check if the error
do NOT try to troubleshoot any further.
Check that the Encoder Strip is NOT damaged or dirty. If necessary, clean the encoder strip,
or if damaged, replace the Encoder Strip. Clean and lubricate the slider rods. Replace YĆaxis
Motor Assembly. Replace Tensioner Holder Assembly (with spring). Replace YĆaxis belt.
ReplaceCarriageAssembly.
System Error:
020011 Ć Refer to Error Code 020010.
HP DesignJet 2500CP and 2000CP Printers
6
Quick Reference Service Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
System Error:
040xxx Ć Press ENTER and switch the printer OFF. Make sure the MIO
card is installed correctly and switch the printer ON again. If this error code continues to
appear then replace the MIO Card. If the system error continues to appear after replacing the
MIO card, replace Electronics Module.
System Error:
System Error:
040601 Ć Install latest version of the MIO Card.
050000 Ć Clean Mark Encoder. Check Line Sensor is installed/connected
correctly. Perform Service Accuracy Calibration. Replace lens cover which is installed on the
line sensor. Replace Line Sensor Assembly. Replace Trailing Cable. Replace Carriage
Assembly. Replace Electronics Module.
System Error:
060000 Ć Close the Window if it is open. Move the printer to a location
with less light. The Printer MUST be kept away from direct intense sunlight or a spotlight.
Replace the Line Sensor Assembly. Replace the Trailing Cable. Replace the Carriage
Assembly. Replace the Electronics Module.
System Error:
060100 Ć Calibrate Line Sensor. Clear EEROM and perform all
calibrations again. Replace Electronics Module and perform all calibrations
System Error:
System Error:
System Error:
060200 Ć Incompatible Firmware and Carriage PCA. Upgrade Firmware.
060300 Ć Incompatible Firmware and Line Sensor. Upgrade Firmware.
060400 Ć Incompatible Carriage PCA and Line Sensor. Replace Line
Sensor. Calibrate Line Sensor.
System Error:
System Error:
060500 Ć Calibrate Line Sensor.
07xxxx Ć Firmware Error. Make sure you have the latest version of the
Flash SIMM (firmware) installed or upgrade the firmware revision of the Flash SIMM. If the
error code remains after installing the latest Flash SIMM then report the error to the HP
Response Center or the nearest HP Support Office, stating the following information:
D
D
D
D
D
Model and Serial Number of the printer.
the complete error number.
service print (Utilities / Service Tests).
plot file where the error has occurred.
additional comments about the usage, the setting, etc..
HP DesignJet 2500CP only
System Error:
System Error:
08xxxx - PostScript Error. Refer to Error Code 07xxxx
080001 - Hard Disk Drive installed without PostScript.
HP DesignJet 2500CP and 2000CP Printers
Quick Reference Service Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HP DesignJet 2500CP only
System Error:
09xxxx Ć HardDisk Drive Error. Switch the printer OFF andON again. If
Error Code reappears, check that the Hard Disk data cable is correctly connected at both
ends. Also check that the Hard Disk Power Cable is correctly connected. Replace Hard Disk
data cable. If Error Code continues to appear, replace Hard Disk.
System Error:
090004 - PostScript installedwithout HardDisk Drive.
Service Tests
Enteringthe Service Tests (Diagnostics) Menu System
1 Holdthe UP andENTER keys down andswitch printer ON from the power switch on
the back of the printer. Wait until Status/Initializing" is displayed before releasing keys.
2 Once Status/Ready" is displayed, scroll to Utilities / Service Tests / Diagnostics andpress
Enter button. Use Arrow buttons to scroll through test selections andpress Enter
button to begin a specific test.
WARNING:
Only replace one component at a time and check if the error has gone
before replacinganother component. Usingthis procedure you will be
able to determine exactly which component failed.
D01. Electronics
Purpose Ć Test Electronics Module, Hard Disk, Line Sensor (only presence), Trailing Cable
andCarriage Assembly (d oes not test the MIO Card).
If D0100 OK" Ć Test Passed.
If D0101 Fail", D0102 Fail" or D0103 Fail" Ć Replace Electronics Module.
If D0104 Fail" Ć Check HardDisk Power Cable is correctly connected. Replace HardDisk
data cable. If Error Code continues, replace Hard Disk.
If D0105 Fail" Ć Check if Line Sensor is installed/connected correctly. Check/replace
Trailing Cable. Replace Carriage Assembly.
If D0106 Fail" Ć Remove Printheads and clean flex contacts on Carriage Assembly and
Printheads. Reseat Printheads and try test again. Perform the Printhead Continuity test.
Replace the complete Ink Delivery System of each color one by one, performing this test each
time. Check/replace Trailing Cable. Replace Carriage Assembly.
D02. Line Sensor
Purpose Ć Test the Line Sensor.
REPLACE THE LENS COVER BEFORE YOU PERFORM THIS TEST IN
ORDER TO PREVENT ANY AEROSOL PROBLEMS.
If Green OK V: ##.## / Blue OK V: ##.##" Ć Test Passed.
If Green Fail V: ##.## / Blue Fail V: ##.##" Ć Replace the lens cover on the Line
Sensor. Make sure that the Mark Encoder on the Driver Roller is clean. Perform the
Electronics test. Check if the Media used is suitable for the printer. Check if the Line Sensor
is installed/connected correctly. Replace Line Sensor.
HP DesignJet 2500CP and 2000CP Printers
8
Quick Reference Service Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
D03. Carriage Axis (YĆaxis)
Purpose Ć Test components of the Carriage Axis.
If D0300 OK" Ć Test Passed.
If D0301 Fail", D0302 Fail" or D0303 Fail" Ć Apply lubricant to the slider rods. Replace
Encoder Strip. Replace YĆaxis Motor Assembly.
If D0304 Fail" Ć Replace encoder strip.
D04. Media Axis (XĆaxis)
Purpose Ć Test the components of the Media Axis.
If D0400 OK" Ć Test Passed.
If D0401 Fail", D0402 Fail" or D0403 Fail" Ć Replace the XĆaxis Assembly.
If D0404 Fail" Ć Clean Mark Encoder. Check Line Sensor is installed correctly. Perform
Service Accuracy Calibration. Replace lens cover installed on line sensor. Replace Line Sensor
Assembly. Replace Trailing Cable. Replace Carriage Assembly. Replace Electronics Module.
D05. Service Station
Purpose Ć Test the Service Station, including Primer Assembly.
If D0500 OK" Ć Test Passed.
If D0501 Fail" Ć Replace the Primer Assembly.
If D0502 Fail" Ć Check if Service Stationflag is installed correctly. Check Service Station
interconnect cable. Replace Service Station Assembly.
D06. Refill
Purpose Ć Test Refill Assembly and Elevator Assembly.
If D0600 OK" Ć Test Passed.
If D0601 Fail" Ć Check Refill interconnect cable. Replace Refill Assembly.
If D0602 Fail" Ć Replace Elevator Assembly.
D07. Front Panel
PurposeĆ Test the frontĆpanel keys.
If required key is not pressed within 10 seconds, D0701 Fail" is displayed.
If all the keys are pressed and the test passes, D0700 OK" is displayed.
If any of the keys are pressed but not recognized then D0701 Fail" is displayed after 10
seconds Ć Check that the Front Panel Assembly cable is connected to the Electronics Module.
Replace Front Panel Assembly.
HP DesignJet 2500CP and 2000CP Printers
Quick Reference Service Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
D08. Sensors
Purpose Ć Test Window, Right and Left Door, Refill Valve, Standby Button, Media and
Pincharm Sensors.
If D0800 OK" Ć Test Passed.
If D0801 Fail" Ć Checkthat the Window Sensor is seated correctly. Check/replace Window
Sensor cable.
If D0802 Fail" Ć Checkthat the Right Door Sensor is seated correctly. Check/replace the
Right Door Sensor.
If D0803 Fail" Ć Checkthat the Left Door Sensor is seated correctly. Check/replace the Left
Door Sensor.
If D0804 Fail", D0805 Fail", D0806 Fail" or D0807 Fail" Ć Checkthe Refill Valve
Sensor cable. Checkthe Refill interconnect cable. Replace the Refill Assembly.
If D0808 Fail" Ć CheckStandby Button Sensor cable. Replace Standby Button Assembly.
If D0809 Fail" Ć CheckMedia Sensor cable. Replace the Media Sensor Assembly.
If D0810 Fail" Ć CheckPincharm Sensor cable. Replace the Pincharm Sensor Assembly.
D09. MIO Presence
Purpose Ć Test the presence of MIO Card and the communication between MIO Card and
Main PCA.
If D0900 OK" Ć Test Passed.
If D0901 Fail" Ć Reseat/replace MIO card.
D10. Cutter
Purpose Ć Test Cutter Assembly.
If carriage picks up the Cutter Assembly and runs it along the length of the printer twice,
test has passed.
If the carriage does not pickup the Cutter Assembly, test has failed Ć Checkif the Cutter
has been disabled through the frontĆpanel (Device Setup / Cutter). Perform Carriage test.
Replace Cutter Assembly.
D11. Bail
Purpose Ć Test the Bail Assembly.
If Bail Assembly is raised, test has passed.
If Bail Assembly is NOT raised, test has failed Ć Replace Bail stepper motor. Replace Bail
assembly.
HP DesignJet 2500CP and 2000CP Printers
10 Quick Reference Service Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
D12. Image Quality
Purpose Ć Test the image quality attributes ofthe printer.
Ifafter aligning the Printheads, Bad Printhead Alignment" is displayed Ć Try recovering the
printheads using the frontĆpanel menu. Check the alignment pattern to check ifany ofthe
colors are printed badly. Ifa color is printing badly then replace the complete Ink Delivery
System ofthe color that is bad. Perform the Line Sensor calibration. Replace the lens cover
'
Users Guide, Chapter 10 (Lens Maintenance). Check ifthe Line Sensor is installed/connected
correctly. Perform the Line Sensor Test. Perform the Electronics Test.
Ifthe values ofthe Printheads are between -1.0 and +1.0 for any of the Printheads then
the test has passed.
Ifthe values ofthe Printheads are NOT between -1.0 and +1.0 for any of the Printheads
then the test has failed Ć Perform the Printhead Alignment Calibration. Perform the Line
Sensor calibration. Replace the lens cover ' Users Guide, Chapter 10 (Lens Maintenance).
Perform the Electronics test. Check if the Media used is suitable for the printer. Check if the
Line Sensor is installed/connected correctly. Replace the Line Sensor.
D13. Printhead ID
Purpose Ć Check the default settings of the printheads. ID 200000 is for inks for imaging and
ID 220000 is for UV Durable Inks.
This test is for information only which might be requested in the event of an escalation.
D14. Printhead Continuity
Purpose Ć Check the primitives and address maps ofthe printheads.
The values shown for all Printheads should be 0. If a different value is shown then that
Printhead has a continuity problem. Try the following:
1 DO NOT replace any parts. This will cause extra problems. Remove the
Printheads and clean the flex contacts on the Carriage and the Printheads. Reseat the
Printheads and try the test again.
2 Even if one of the Printheads failed the Printhead Continuity test, you must remove all the
Printheads from the Carriage and try installing them one by one. Before installing each
Printhead, check the continuity of all four Printheads. The frontĆpanel should display a
3ffff / 3fff result for each Printhead that is not inserted and the original values (the value
that was displayed before the Printhead was removed) for the Printheads when they are
inserted. If you get a value that is different than 3ffff / 3fff when the Printheads are
removed then you must perform step 1 again. If you get the same results after repeating
step 1, then the carriage is damaged. Replace the Carriage Assembly. When you insert each
Printhead, the values should change only for that Printhead. If the values of other
Printheads also change, then the problem is the Printhead itself and not the actual Printer.
In this case you must replace the complete Ink Delivery System of the color that failed.
3 If you continue getting the original value (the value that was displayed before the
Printhead was first removed) then you must replace the complete Ink Delivery System of
the color that failed and try the test again.
4 As a last resort, replace Carriage Assembly.
D15. Clean Roller
Purpose Ć To rotate the Drive Roller when it requires cleaning.
HP DesignJet 2500CP and 2000CP Printers
Quick Reference Service Manual 11
Download from Www.Somanuals.com. All Manuals Search And Download.
D16. Erase EEROM
Purpose Ć To clear the EEROM.
If D1600 OK" Ć EEROM erased correctly.
If D1601 Fail" Ć Replace Electronics Module.
D17. Reset Counters
Purpose Ć To reset the internal counters.
If D1700 OK" Ć Counters reset correctly.
If D1701 Fail" Ć Replace Electronics Module.
D19. HardDisk Drive Revision
Purpose Ć To show the revision of the internal Hard Disk Drive.
Calibrations
Entering the Service Calibrations Menu System
1 Hold the UP and ENTER keys down and switch printer ON from the power switch on
the back of the printer. Wait until Status/Initializing" is displayed before releasing keys.
2 Once Status/Ready" is displayed, scroll to Utilities / Service Tests / Calibrations and
press Enter button. Use Arrow buttons to scroll through selections and press Enter
button to begin a specific calibration.
Calibrations To Be Done
C01 C02 C03 C04 C05 C06 C07 C08
When Required
Electronics Module is replaced
Yes Yes Yes No Yes Yes Yes Yes
Yes Yes Yes No Yes Yes Yes Yes
Carriage is disassembled or replaced
Refill Assembly is disassembled or replaced
Line Sensor is disassembled or replaced
Service station is disassembled or replaced
No Yes No
No Yes No Yes No
No
No
No Yes No Yes Yes Yes Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
XĆaxis Assembly is disassembled or replaced No
No Yes
No Yes
Drive Roller is disassembled or replaced
Banding Problem
No
No
No
No
No
No
No Yes No Yes Yes No Yes
No Yes No No No No No
No Yes No Yes Yes No Yes
No Yes No No No Yes No
No No No No Yes No No
Edge Detect Problem
Misalignment between Colors
Color Accuracy Problem
Nozzles Out or Misdirected
HP DesignJet 2500CP and 2000CP Printers
12 Quick Reference Service Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
C01. Carriage
Purpose Ć Calibrate the temperature from which the printhead has to be warmed.
THIS CALIBRATION MUST BE DONE WITH THE PRINTHEADS INSTALLED.
If C0100 OK" Ć Calibration done.
If C01xx Fail" Ć Perform Electronics test.
C02. Refill
Purpose Ć To ensure the correct position of the carriage assembly in respect to the refill assembly.
When the Carriage Assembly, Refill Assembly or the Electronics Assembly is ordered, a Refill
Calibration Tool, a special Carriage height gauge and an Instructions flyer will be included.
You must follow the instructions in the flyer in order to correctly calibrate the Refill
Assembly and to make sure that the Carriage is at the correct height.
C03. Line Sensor
Purpose Ć Calibrate the intensity of the line sensor in the carriage PCA.
Load white media before performing this calibration.
WINDOW MUST CLOSED BEFORE YOU PERFORM THIS CALIBRATION.
REPLACE THE LENS COVER BEFORE YOU PERFORM THIS
CALIBRATION IN ORDER TO PREVENT ANY AEROSOL PROBLEMS.
If C0300 Done" Ć Calibration done.
C04. Service Station
THIS CALIBRATION IS NO LONGER VALID AND SHOULD NEVER BE
PERFORMED.
C05. Printheads Alignment
Purpose Ć To test and if necessary correct the misalignment between the printheads.
WINDOW MUST CLOSED BEFORE YOU PERFORM THIS CALIBRATION.
If C0500 Done" Ć Calibration done.
If C0501 Fail" Ć If the calibration pattern is bad, try recovering printheads using the
frontĆpanel menu and try the calibration again. If the calibration pattern is bad again, then
replace the complete Ink Delivery System of the color that is bad. Perform Electronics Test.
Perform Line Sensor Test.
HP DesignJet 2500CP and 2000CP Printers
Quick Reference Service Manual 13
Download from Www.Somanuals.com. All Manuals Search And Download.
C06. Printheads Check
Purpose Ć Check that the Nozzles of the Printheads are functioning correctly.
WINDOW MUST CLOSED BEFORE YOU PERFORM THIS CALIBRATION.
If C0600 Done" Ć Calibration done.
If C06xx Fail" Ć If the calibration pattern is bad, try recovering printheads using the
frontĆpanel menuand try the calibration again. If the calibration pattern is bad again, then
replace the complete Ink Delivery System of the color that is bad. If the calibration pattern is
good, replace Line Sensor. Perform Electronics Test. Perform Line Sensor Test.
C07. Color Calib. (Only available in the HP DesignJet 2500CP printer)
Purpose Ć To determine the correction function to be applied in PostScript in order to match
the color reproduction of a nominal Printer. This Calibration is necessary to improve color
consistency between different prints and different Printers.
WINDOW MUST CLOSED BEFORE YOU PERFORM THIS CALIBRATION.
If C0700 Done" Ć Calibration done.
If C0701 Fail" Ć If the calibration pattern is bad, try recovering printheads using the
frontĆpanel menuand try the calibration again. If the calibration pattern is bad again, then
replace the complete Ink Delivery System of the color that is bad. Perform Electronics Test.
Perform Line Sensor Test.
C08. Service Accuracy
Purpose Ć Calibrate the nominal advance of the media.
WINDOW MUST CLOSED BEFORE YOU PERFORM THIS CALIBRATION.
You must use HP Matte film to perform this calibrationevenif it is not
supported. You can select it as any media in the frontĆpanel.
If C0800 Done" Ć Calibration done.
If C0801 Fail" Ć If the calibration pattern is bad, try recovering printheads using the
frontĆpanel menuand try the calibration again. If the calibration pattern is bad again, then
replace the complete Ink Delivery System of the color that is bad. If the calibration pattern is
good, replace Line Sensor. Perform Electronics Test. Perform Line Sensor Test.
HP DesignJet 2500CP and 2000CP Printers
14 Quick Reference Service Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
C09. Maintenance
Purpose Ć To read and, if necessary, adjust the preventive maintenance counter, which counts
the number of swaths.
This Calibration must be used to reset the Maintenance counter to ZERO
after the Preventive Maintenance Kit has been installed in order to disable
the Maintenance Advised" message on the frontĆpanel.
Note down the Swaths Counter (####) before replacing the Electronics Module.
Adjust the Swaths Counter (####) after replacing the Electronics Module.
Use the following keys to adjust the swaths counter.
D Up Arrow Ć Increase the Counter Digit.
D Down Arrow Ć Decrease the Counter Digit.
D Enter Ć Select the Next digit.
C10. Font Type Set (Only available in HP DesignJet 2500CP printer)
Purpose Ć To check and, if necessary, select a Font type (only possible when the printer
detects that a new Hard Disk has been installed).
YOU MUST PERFORM THIS CALIBRATION WHEN YOU INSTALL A NEW
ELECTRONICS MODULE IN ORDER TO SET THE CORRECT FONT TYPE.
If you have not installed a new Electronics Module, current font type will be displayed.
If you have installed a new Electronics Module, Character Set New" will be displayed. Press
Up Arrow key to set new type font.
The message Choose Character Set" will be displayed on the frontĆpanel. Use Up and
Down Arrow keys to select font type required and then press Enter.
The first time a PostScript print is sent to the printer, the other font types will be deleted
and cannot be recovered.
IF YOU DO NOT SELECT ANY FONT SET, THE ROMAN FONT WILL BE
SELECTED BY DEFAULT WHEN A POSTSCRIPT FILE IS SENT.
HP DesignJet 2500CP and 2000CP Printers
Quick Reference Service Manual 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|