NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY MAGNUM V
HOME GYM
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MACH V
Retain This
Manual for
Reference
08-26-03
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended this machine be assembled by two or more
people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach two Ø 2 ½” Rubber Bumpers (#88) to the holes on the Main Base Frame (#1).
B.) Align the holes and insert two Guide Rods (#10) into the holes. Secure the Guide
Rods from the Bottom of Main Base Frame with two M10 x ¾” Allen Bolts (#120) and
Ø ¾” Washers (#124).
DIAGRAM 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Connect the Main Base Frame (#1) to both the Front & Rear Stabilizers (#5 & 4). Secure each end
with two M10 x 2 ¾” Carriage Bolts (#109), one 4 ¾” x 2” Bracket (#44), two ∅ ¾” Washers
(#124), and two M10 Aircraft Nuts (#128). DO NOT tighten all the nuts and bolts yet.
B.) Attach the Rear & Front Vertical Beams (#6 & 7) to the Main Base Frame (#1). Secure each Beam
with two M10 x 2 ¾” Carriage Bolts (#109), ∅¾” Washers (#124), and M10 Aircraft Nuts (#128).
C.) Place the Upper Frame (#8) onto the Front & Rear Vertical Beams. Secure the Upper Frame to
Rear Vertical Frame with two M10 x 2 ¾” Carriage Bolts (#109), ∅ ¾” Washers (#124), and M10
Aircraft Nuts (#128).
D.) Secure the Upper Frame to the Front Vertical Beam with two M10 x 3 ½” Carriage Bolts (#108),
one 6 ¼” x 2” Bracket (#43), two ∅ ¾” Washers (#124), and two M10 Aircraft Nuts (#128).
E.) Attach the Lat Bar Holder (#31) to the front of the Upper Frame (#8). Secure it with one M10 x 2
¾” Carriage Bolt (#109), ∅ ¾” Washer (#124), and M10 Aircraft Nut (#128).
F.) Securely tighten all Bolts and Nuts.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Place the Swivel Frame (#11) onto the axle on the Main Base Frame (#1). Secure it with one
M10 x ¾” Allen Bolt (#120) and Ø ¾” Washer (#124).
B.) Attach the Foot Support (#12) to the Main Base Frame. Attach the 4” x 2” Bracket (#42) to
the opposite side on the Main Base Frame. Secure them with one M10 x 2 ¾” Carriage Bolt
(#109), Ø ¾” Washer (#124), and M10 Aircraft Nut (#128) to the hole near the Rear
Stabilizer. Secure the other hole with a M10 x 2 ½” Allen Bolt (#117) and Ø ¾” Washer
(#124).
DIAGRAM 3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Butterfly Support Frame (#15) to the front of the Front Vertical Beam (#7). Attach the
Butterfly Pulley Support (#16) to the back of the Front Vertical Beam (#7). Align the holes and
secure them with two M10 x 3 ¾” Carriage Bolts (#107), ∅ ¾” Washers (#124), and M10 Aircraft
Nuts (#128).
B.) Attach a Pull Pin (#74) to the Left Butterfly Arm (#29). Repeat for the Right Butterfly Arm (#30).
C.) Slide a Butterfly Pulley Cam (#17) onto the axle on the Left Butterfly Arm (#29). Make sure the
Clip on the Cam is on the outside. Insert the axle into the hole on the Butterfly Support Frame
(#15) from the bottom up. Secure it with a ∅1 ½” x ∅ ¾” Washer (#79) and ∅ 1 3/8” Ring Cap
(#78). Secure the Ring Cap with one M6 x 1 5/8” Hex Bolt (#111) and M6 Aircraft Nut (#129).
D.) Repeat Step C above to install the Right Butterfly Arm (#30).
E.) Slide a ∅ 1 ½” x Ø 5/8” Washer (#131) onto the bottom axle on the Left Butterfly Arm (#29).
Attach a Butterfly Handle (#28) onto the axle. Secure it with one M10 x ¾” Allen Bolt (#120) and
Ø ¾” Washer (#124). Repeat the same procedure to install the other side.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Install 19 Weight Plates (#58). To install the plates, hold the plate at an angle and place between
the two Guide Rods (#10) then drop it down. Make sure the grooves on the plastic covers all
face up. The plates should all interlock with each other. It is strongly recommended to spray
lubricant such as WD-40 on the Guide Rods to minimize friction.
B.) Insert the Selector Rod (#62) into the center hole on the Weight Plates. Slide the Selector Stem
(#63) onto the Guide Rods from the top. Align the holes. Secure it to the Selector Rod with one
M10 x 1 ¾” Allen Bolt (#119).
C.) Insert the Weight Plate Selector Pin (#73) in between two plates to select the number of weight
plates for exercise and to secure the Selector Rod. Make sure the magnet on the Pin faces up.
D.) Attach the Top Socket Assembly (#9) to the Upper Frame and top of the Guide Rods. Secure it
to the Upper Frame with two M10 x 2 ¾” Carriage Bolts (#109), one 4 ¾” x 2 ¾” Bracket (#45),
two Ø ¾” Washers (#124), and two M10 Aircraft Nuts (#128).
E.) Secure the Top Socket Assembly (#9) to the Guide Rods (#10) with two M10 x ¾” Allen Bolts
(#120) and Ø ¾” Washers (#124).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP6 (See Diagram 6)
A.) Attach the Bench Press Base (#14) to the opening on the Rear Vertical Beam (#6). Carefully
place two ∅1 ½” x Ø 1” Washers (#132) in between the Base and the Rear Vertical Beam. Align
the holes and insert a 9” Axle (#32). Secure both ends with two ∅1 ½ x ∅ ½”Washers (#133)
and M12 Aircraft Nuts (#127). Do not over tighten the Nuts. Make sure the Base is free to swivel
on the Axle. Close both ends with two Cone-shaped End Caps (#105).
B.) Attach four ∅1” Bushings (#67) to the openings on the Bench Press Frame (#13). Attach the
Bench Press Frame to the Bench Press Base (#14). Align the holes and insert a 13 ¾” Axle
(#33). Secure both ends with two ∅1 ½” x ∅ ½” Washers (#133) and M12 Aircraft Nuts (#127).
Close both ends with two Cone-shaped End Caps (#105).
C.) Lubricate the inside of the Foam Grips (#72) with water then slide them onto the Bench Press
Frame (#13).
D.) To adjust the Bench Press Arm, simply squeeze down the break handle on the right side of the
Press Arm.
DIAGRAM 6
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7)
A.) Slide the Sliding Block (#37) onto the Main Seat Support (#2). Thread a Lock Knob (#87) into
the hole on the Sliding Block to hold it in position.
B.) Attach the rear end of Main Seat Support (#2) to the open bracket on the Front Vertical Beam
(#7). Secure it with three M10 x 2 ¾” Carriage Bolts (#109), Ø ¾” Washers (#124), and M10
Aircraft Nuts (#128).
C.) Place the Main Seat Support (#2) onto the Front Support Frame (#3). Secure it with two M10 x
2 ¾” Carriage Bolts (#109), Ø ¾” Washers (#124), and M10 Aircraft Nuts (#128).
D.) Attach the front bottom of Main Seat Support to the Front Support Frame. Secure it with one
M10 x 2 ¾” Carriage Bolt (#109), Ø ¾” Washer (#124), and M10 Aircraft Nut (#128).
E.) Attach the Seat Bracket (#18) to the pivot on the Main Seat Support (#2). Push two Ø 3/8”
Bushings (#69) through the holes on Seat Bracket into the pivot.
F.) Attach the Backrest Support (#25) to each end of the Backrest Incline Support (#22). Attach the
front holes on the Backrest Supports (#25) to the pivot. Align the holes and secure them with
one M10x7¼” Hex Bolt (#110), two Ø ¾” Washers (#124) and one M10 Aircraft Nut (#128).
G.) Attach the bottom of the Backrest Incline Support (#22) to the bracket on the Sliding Block
(#37). Secure it with one M10 x 3” Allen Bolt (#116), two Ø ¾” Washes (#124), and one M10
Aircraft Nut (#128).
H.) Attach the Leg Developer (#26) to the open bracket on the Main Seat Support (#2). Secure it
with a 2 ½” Axle (#139), two Ø ¾” Washers (#124), and two M10 x ¾” Allen Bolts (#120).
I.) Attach the Curl Bar Handle (#21) to the Leg Developer. Secure it with a 3” L-shaped Pin (#138).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8)
A.) Attach Backrest Board (#48) to the Front Vertical Beam (#7). Secure it with two M8 x 3 3/8”
Allen Bolts (#115) and Ø 5/8” Washers (#125).
B.) Attach the Adjustable Backrest Board (#49) to the Backrest Supports (#25). Secure it with four
M6 x 1 3/8” Hex Bolts (#112) and Ø ½” Washers (#126).
C.) Place the Seat (#50) onto the Seat Bracket (#18). Secure it to the two rear holes on the Seat
Bracket with two M8 x ¾” Allen Bolts (#122) and Ø 5/8” Washes (#125). Attach a Seat Incline
Adjustment (#19) to the two front holes and secure them with two M8 x ¾” Allen Bolts (#122)
and Ø 5/8” Washers (#125). Insert a 4” L-shaped Pin (#137) through the selected hole on the
Seat Incline Adjustment to hold the desired height.
D.) Insert one Foam Tube (#27) halfway through the hole on the Main Seat Support (#2). Insert two
Foam Tubes halfway through the holes on the Leg Developer (#26). Push six Foam Rolls (#71)
onto the Tubes from both ends. Plug six Foam Roll End Caps (#102) into the ends.
E.) Attach the Arm Curl Pad (#51) to the Arm Curl Stand (#20). Secure it with two M8 x 5/8” Allen
Bolts (#121) and Ø 5/8” Washers (#125). Insert the Arm Curl Stand into the opening on the
Main Seat Support. Use the Lock Knob to lock the desired Arm Curl exercise height. Remove
the Arm Curl Stand and Curl Bar Handle when doing Leg Developer exercises.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9)
A.) Attach the two Weight Stack Covers (#39) to the Top Socket Assembly (#9) and Main Base
Frame (#1). Secure each Cover with two M10 x ¾” Allen Bolts (#120) and Ø ¾” Washers
(#124).
DIAGRAM 9
15
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 10 (See Cable Loop Diagram & Diagram 10)
A.) Attach one end of the 143” Butterfly Cable (#56) to the Clip on the Butterfly Pulley Bracket (#17)
on the right side. Draw the Cable to the Butterfly Pulley Support (#16).
B.) Attach a Pulley (#66) to the open bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#113), two
Ø ¾” Washers (#124), and one M10 Aircraft Nut (#128).
C.) Draw the Cable over the Pulley then pull downward. Repeat Step B above to install a Pulley to
the Single Floating Pulley Bracket (#35). Let the Pulley hanging for now.
D.) Draw the Cable around the Pulley then pull upward to the open bracket on the left side of the
Butterfly Pulley Support (#16). Repeat Step B to install another Pulley.
E.) Draw the Cable over the Pulley then to the left Butterfly Pulley Bracket. Secure the end of the
Cable to the Clip.
DIAGRAM 10
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 11 (See Cable Loop Diagram & Diagram 11)
A.) Attach the 118” Upper Cable (#52) to the front opening on the Upper Frame (#8). Attach a
Pulley to the opening. Secure the Pulley with one M10 x 2 ½” Allen Bolt (#117), two Ø 7/8”
Pulley Bushings (#70), and one M10 Aircraft Nut (#128). Make sure the Ball Stopper of the
Cable is underneath the Frame.
B.) Draw the Cable over the Pulley and toward the back of the machine. Attach a Pulley to the
open bracket on the top of the Upper Frame. Secure the Pulley with one M10 x 1 ¾” Allen
Bolt (#113), one L-shaped Pulley Bracket (#46), two Ø ¾” Washers (#124), and one M10
Aircraft Nut (#128).
C.) Draw the Cable over the Pulley and pull downward. Attach a Pulley to an Angled Double
Floating Pulley Bracket (#34). Secure it with one M10 x 1 ¾” Allen Bolt (#113), two Ø ¾”
Washers (#124), and one M10 Aircraft Nut (#128). Draw the Cable around the Pulley then
pull upward to the opening on the Top Socket Assembly (#9). Let the Bracket hanging for
now.
D.) Repeat the Step A above to install a Pulley to the opening.
E.) Draw the Cable over the Pulley then to the open bracket on the top of the Top Socket
Assembly (#9). Repeat Step B above to install a Pulley.
F.) Draw the Cable around the Pulley then pull downward to the Selector Rod (#62). Screw
the Bolt on the end of Cable into the Selector Rod. Make sure to tighten down the nut on
the bolt against the Selector Rod.
G.)Connect a Short Chain (#134) to the end of the Cable with a C-clip (#136). Connect the
Lat Bar (#23) to the Short Chain with another C-clip. Adjust the length of Chain to adjust
the Lat Bar exercise height.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 11
19
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 12 (See Cable Loop Diagram & Diagram 12)
A.) Attach the Ball-end of the 163” AB Cable (#55) to the opening on the Front Vertical
Beam (#7). Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt
(#117), two Ø 7/8” Pulley Bushings (#70), and one M10 Aircraft Nut (#128). Use a C-clip
(#136) to connect the AB Strap (#59) to the end of the Cable.
B.) Draw the Cable over the Pulley then pull downward and over the Small Pulley Wheel
(#65) to the second open bracket on the Main Base Frame (#1). Attach a Pulley and U-
shaped Pulley Bracket (#47) to the bracket.
C.) Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#113), two Ø ¾” Washes (#124), and
one M10 Aircraft Nut (#128).
D.) Draw the Cable around the Pulley then Pull upward to the Angled Double Floating Pulley
Bracket (#34) previously installed in Step11-C. Repeat Step C above to install another
Pulley.
E.) Draw the Cable over the Pulley then pull downward. Attach the Cable to a Pulley.
Repeat Step C above to install the Pulley to a Double Floating Pulley Bracket (#36). Let
the Bracket hanging for now.
F.) Draw the Cable around the Pulley then pull the Cable upward. Use a C-clip (#136) to
connect the end of Cable to a Short Chain (#134). Secure the Short Chain to the Rear
Vertical Beam (#6) with one M10 x 1” Allen Bolt (#114), two Ø ¾” Washers (#124), and
one M10 Aircraft Nut (#128).
G.)After completing the entire cable installation, check the tightness of the Cable loop
system. Adjust the tension of Cables by adjusting the length of the Short Chain. If the
Cables are too loose, shorten the Chain.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 12
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 13 (See Cable Loop Diagram & Diagram 13)
A.) Attach one end of the 78” Bench Press Cable (#54) to a Single Floating Pulley Bracket (#35).
Secure it with one M10 x 1” Allen Bolt (#114), two Ø ¾” Washers (#124), and one M10 Aircraft
Nut (#128). Let the Bracket hanging for now.
B.) Pull the Cable upward to the opening between the Bench Press Base (#14). Attach a Pulley to
the opening. Secure it with one 7” Axle (#130) and two M8 Hex Socket Screws (#82).
C.) Draw the Cable around the Pulley then pull downward to the third open bracket on the Main
Base Frame (#1). Attach a Pulley and a L-shaped Pulley Bracket (#46) to the bracket.
D.) Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#113), two Ø ¾” Washers (#124), and one
M10 Aircraft Nut (#128).
E.) Draw the Cable underneath the Pulley and through the opening underneath the second Pulley
previously installed. Draw the Cable to the first open bracket on the Main Base Frame (#1).
Repeat Step D above to install another Pulley.
F.) Draw the Cable around the Pulley then pull upward to the Single Floating Pulley Bracket (#35)
previously installed in Step10-C. Secure the Cable with one M10 x 1” Allen Bolt (#114), two Ø
Washers (#124), and one M10 Aircraft Nut (#128).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 14 (See Cable Loop Diagram & Diagram 14)
A.) Attach the 163” Lower Cable (#53) to the Swivel Frame (#11).
B.) Install a Pulley to the bracket on the Swivel Frame with one M10 x 1 ¾” Allen Bolt
(#113), two Ø ¾” Washers (#124), one L-shaped Bracket (#46) and one M10 Aircraft
Nut (#128).
C.) Draw the Cable around the Pulley then pull upward to the Double Floating Pulley
Bracket (#36) previously installed in Step12-E. Install another Pulley.
D.) Draw the Cable around the Pulley then pull downward to the first open bracket on the
left. Repeat the Step B above to install a Pulley with a U-shaped Pulley Bracket (#47).
E.) Draw the Cable around the Pulley then pull upward to the Single Floating Pulley
Bracket (#35) previously installed in Step 13-A. Repeat Step B above to install a Pulley.
F.) Draw the Cable around the Pulley then pull downward to the open bracket on the Main
Base Frame. Repeat Step B above to install a Pulley with a L-shaped Pulley Bracket
(#46).
G.)Draw the Cable underneath the three Pulleys previously installed in Step 13 and
through the opening on the bottom of the Front Vertical Beam (#7). Continuously draw
the Cable underneath the Small Pulley Wheel (#65) on the Main Base Frame to the
opening on the Front Support Frame (#3). Attach a Pulley to the opening. Secure it with
one M10 x 2 ½” Allen Bolt (#117), two Ø 7/8” Pulley Bushings (#70), and one M10
Aircraft Nut (#128).
H.) Draw the Cable over the Pulley and to the open bracket on the Main Seat Support (#2).
Repeat Step B above to install a Pulley.
I.) Draw the Cable through the opening on the Main Seat Support to the open bracket on
the Leg Developer (#26). Secure the end of Cable with one M10 x 1” Allen Bolt (#114),
two Ø ¾” Washers (#124), and one M10 Aircraft Nut (#128).
J.) Use a C-clip (#136) to connect a Long Chain (#135) to the end of the Cable. Use
another C-clip to connect the Shiver Bar (#24), Single Handle (#61), or Ankle Strap
(#60) for various exercises.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
3
2
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
2
1
6
2
1
1
1
1
1
1
1
1
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
143” Butterfly Cable
Wire
Weight Plate
AB Strap
Ankle Strap
Single Handle
Selector Rod
Selector Stem
1
1
19
1
1
1
1
1
1
2
22
18
6
2
8
6
2
1
2
1
1
1
2
2
2
2
2
4
1
4
2
2
2
1
2
2
2
2
1
1
4
1
2
3
4
Main Base Frame
Main Seat Support
Front Support Frame
Rear Stabilizer
5
Front Stabilizer
6
7
8
Rear Vertical Beam
Front Vertical Beam
Upper Frame
Foot Support Panel
Small Pulley Wheel
Pulley
9
Top Socket Assembly
Guide Rod
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Swivel Frame
Foot Support
Ø 1” Bushing
Ø 5/8” Bushing
Ø 3/8” Bushing
Ø 7/8” Pulley Bushing
Foam Roll
Foam Grip
Weight Plate Selector Pin
Pull Pin Set
Pull Pin Nut
Pull Pin Adjustment
Spring
Ø 1 3/8” Ring Cap
Ø 1 ½” x Ø ¾” Washer
1 ¼” Philips Screw
5/8” Philips Screw
M8 Hex Socket Screw
M5 x 3/8” Philips Screw
Wire Control Handle Grip
6” Handle Grip
Bench Press Frame
Bench Press Base
Butterfly Support Frame
Butterfly Pulley Support
Butterfly Pulley Cam
Seat Bracket
Seat Incline Adjustment
Arm Curl Stand
Curl Bar Handle
Backrest Incline Support
Lat Bar
Shiver Bar
Backrest Support
Leg Developer
Foam Tube
Butterfly Handle
Left Butterfly Arm
Right Butterfly Arm
Lat Bar Holder
9” Axle
13 ¾” Axle
Curl Bar Grip
Lock Knob
Ø 2 ½” Rubber Bumper
∅ 1 ¾” Rubber Bumper
∅ 1 5/8” Rubber Bumper
Lat Bar Grip
Ø 2 3/8” Washer
2 3/8” x 2” Sleeve
2” x 1 ¾” Sleeve
2” Square End Cap
2” Stabilizer End Cap
2 3/8” x 1 5/8” End Cap (Impex) 2
2 ¾” x 2” End Cap
2” Square End Cap (Impex)
1 ½” Square End Cap (Impex)
1” Square End Cap
Foam Roll End Cap
3 1/8” x 1 5/8” End Cap
Ø 1” x1” Bushing
Cone-shaped End Cap
Ø 5/8” x ¼” Bushing
M10 x 3 ¾” Carriage Bolt
M10 x 3 ½” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
Angled Double Floating Pulley Bracket
Single Floating Pulley Bracket
Double Floating Pulley Bracket
Sliding Block
Curl Bar Handle Tube
Weight Stack Cover
Wire Control Handle
Shiver Bar Handle
4” x 2” Bracket
6 ¼” x 2” Bracket
4 ¾” x 2” Bracket
4 ¾” x 2 ¾” Bracket
L-shaped Bracket
U-shaped Bracket
Backrest Board
Adjustable Backrest Board
Seat
Arm Curl Pad
118” Upper Cable
163” Lower Cable
78” Bench Press Cable
163” AB Cable
1
8
2
2
6
2
4
4
2
2
2
20
25
Download from Www.Somanuals.com. All Manuals Search And Download.
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
M10 x 7 ¼” Hex Bolt
M6 x 1 5/8” Hex Bolt
M6 x 1 3/8” Hex Bolt
M10 x 1 ¾” Allen Bolt
M10 x 1” Allen Bolt
M8 x 3 3/8” Allen Bolt
M10 x 3” Allen Bolt
M10 x 2 ½” Allen Bolt
Ø ¾” Bushing
M10 x 1 ¾” Allen Bolt (Full Thread)
M10 x ¾” Allen Bolt
M8 x 5/8” Allen Bolt
M8 x ¾” Allen Bolt
M6 x 5/8” Allen Bolt
Ø ¾” Washer
1
2
4
17
4
2
1
5
2
1
13
2
4
3
84
8
4
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
M410 Aircraft Nut
M6 Aircraft Nut
7” Axle
Ø 1 ½” x Ø 5/8” Washer
Ø 1 ½” x Ø 1” Washer
Ø 1 ½” x Ø ½” Washer
Short Chain
Long Chain
C-clip
4” L-shaped Pin
3” L-shaped Pin
M10 x 2 ½” Axle
M6 x ¾” Adjustment Screw
M6 x ½” Adjustment Nut
1 ¾” Square End Cap
Ø 1 ½” End Cap
Ø 1” End Cap
Ø 1 ¼” End Cap
Ø 1 5/8” x 1 ½” Bushing
Ø 1 5/8” x 5/8” Bushing
51
2
1
2
2
4
2
1
6
1
1
1
2
2
2
2
2
2
2
1
Ø 5/8” Washer
Ø ½” Washer
M12 Aircraft Nut
4
26
Download from Www.Somanuals.com. All Manuals Search And Download.
MACH IV WEIGHT RESISTANCE CHART
Plate Arm
Curl
Low
Pulley
30
High
Pulley
20
Butterfly
AB
Station
30
Bench
Press
60
0
1
40
50
20
23
26
29
32
35
38
41
44
47
50
53
56
59
62
65
68
71
74
77
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
70
80
90
2
60
3
70
4
80
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
5
90
6
7
8
9
100
110
120
130
140
150
160
170
180
190
200
210
220
230
10
11
12
13
14
15
16
17
18
19
* Numbers are approximate. Actual weights may vary.
* Values for Butterfly are for each arm.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of two years on the Frame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state. Register on-line www.impex-fitness.com
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
28
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Graco Baby Playpen PD243008A User Manual
GrandTec TV Cables GEZ 1000 User Manual
Honeywell Weather Radio TS33F User Manual
Hotpoint Washer WMA64 User Manual
HP Hewlett Packard Network Cables NC6136 User Manual
HP Hewlett Packard Network Card 3C590 User Manual
HP Hewlett Packard Switch JG325A User Manual
Humax TV Receiver LGB 26TPVR User Manual
Humminbird Grinder G 12SE User Manual
Husqvarna Snow Blower 96193006300 User Manual