Grizzly Saw H0629 User Manual

MODEL H0629 ZERO-CLEARANCE/DADO TABLE SAW INSERT  
INSTRUCTIONS  
WARNINGS  
Disconnect saw from power source before fitting or removing insert.  
Always wear eye protection.  
Be sure blade is NOT in contact with insert before switching on.  
Do not attempt to tilt the arbor while the blade is in the insert! The blade will bind, causing severe damage  
and possible injury! For beveled cuts, a separate, dedicated insert must be prepared. Pre-set the angle  
and then proceed as instructed below.  
Insert must be securely clamped down with a board before plunging blade up through it to cut kerf.  
If using blade stabilizers, check clearance before raising blade.  
INSTALLING AND FITTING YOUR INSERT  
1) Lower the blade completely.  
2) Test fit insert in throat opening, back end first, so that anti-lift pin engages under rear edge of tabletop. At  
first, it normally will NOT fit; slightly excessive in both length and width.  
3) This insert is provided with special oversize “fitting bumpers”, two on the left side, and one on the front  
end. Using a medium grit sanding block, lightly sand the bumps down, and test-fit repeatedly, to gradually  
“sneak-up” on a snug, yet easily removable fit. A slight bevel sanded on the bottom of the front bump will  
ease entry.  
4) Back out the four leveling screws, until insert is stable, and flush with tabletop.  
5) SPLITTER: If this insert is to be used with a splitter, you will need to finish cutting out the pre-routed  
optional splitter slot, using a saw or router. Break sharp edges with sandpaper.  
CUTTING THE BLADE SLOT (KERF)  
1) Check that insert is fitted properly, and that blade is clear. Using a stick, reach under the table and rotate  
the blade manually to check for blade clearance.  
2) Fully cover the insert with a board, and clamp at each end to the table saw top.  
3) Re-connect power to saw. Switch on, slowly and cautiously raise blade up, to cut its way through the  
insert. KEEP HANDS OFF OF TABLE TOP, STAY CLEAR AND WEAR EYE PROTECTION. Raise blade  
to maximum height at this time.  
4) Lower blade, turn off saw, and remove board. Your insert is now ready for use!  
IMPORTANT TIPS FOR USE  
Only recommended for use with carbide tipped cutters.  
DADO BLADE - Use same procedures outlined above, but use additional caution due to excessive mate-  
rial being machined from insert during the slotting procedure.  
Under certain conditions, an undesirable scraping noise may be generated by your saw blade. Planer type  
blades and/or excessive arbor run-out, and/or blade distortion, may be causing intermittent contact with  
the insert slot. To remedy this, remove the insert and slightly widen the slot using a file or sanding paddle.  
Ideally, a separate insert should be used with each blade, dado stack, or angle set-up. This will insure a  
true “zero-clearance” effect and give you maximum benefit from your inserts.  
318600622  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ZERO-CLEARANCE/DADO TABLE SAW INSERT  
INSTRUCTIONS  
WARNINGS  
Disconnect saw from power source before fitting or removing insert.  
Always wear eye protection.  
Be sure blade is NOT in contact with insert before switching on.  
Do not attempt to tilt the arbor while the blade is in the insert! The blade will bind, causing severe damage  
and possible injury! For beveled cuts, a separate, dedicated insert must be prepared. Pre-set the angle  
and then proceed as instructed below.  
Insert must be securely clamped down with a board before plunging blade up through it to cut kerf.  
If using blade stabilizers, check clearance before raising blade.  
INSTALLING AND FITTING YOUR INSERT  
1) Lower the blade completely.  
2) Place insert in throat opening, back end first, so that anti-lift pin engages under rear edge of tabletop.  
Initially, the insert should be too long; and hit on the front “fitting bumps”.  
3) Using medium grit sanding block, LIGHTLY sand all four fitting bumps. Also, lightly bevel the bottom  
edges of the FRONT bumps to ease entry. Sand, test, repeat — to gradually “sneak-up” on snug, yet eas-  
ily removable fit. Once you have achieved a TIGHT, WEDGE fit, work only FRONT bumps from then on.  
4) Back out the four leveling screws, until insert is stable, and flush with tabletop.  
5) To remove insert, bump the heel of the your hand on rear of insert; front of insert should pop up slightly.  
Alternatively, a 3/4" finger hole can be bored near front of insert to facilitate removal.  
6) SPLITTER: If the insert is to be used with a splitter, you will need to finish cutting out the pre-routed  
optional splitter slot, using a saw or router. Break sharp edges with fine sandpaper.  
CUTTING THE BLADE SLOT (KERF)  
1) Check that insert is fitted properly, and that blade is clear. Using a stick, reach under the table and rotate  
the blade manually to check for blade clearance.  
2) Fully cover the insert with a board, and clamp at each end to the table saw top.  
3) Re-connect power to saw. Switch on, slowly and cautiously raise blade up, to cut its way through the  
insert. KEEP HANDS OFF OF TABLE TOP, STAY CLEAR AND WEAR EYE PROTECTION. Raise blade  
to maximum height at this time.  
4) Lower blade, turn off saw, and remove board. Your insert is now ready for use!  
IMPORTANT TIPS FOR USE  
Only recommended for use with carbide tipped cutters.  
DADO BLADE - Use same procedures outlined above, but use additional caution due to excessive mate-  
rial being machined from insert during the slotting procedure.  
Under certain conditions, an undesirable scraping noise may be generated by your saw blade. Planer type  
blades and/or excessive arbor run-out, and/or blade distortion, may be causing intermittent contact with  
the insert slot. To remedy this, remove the insert and slightly widen the slot using a file or sanding paddle.  
Ideally, a separate insert should be used with each blade, dado stack, or angle set-up. This will insure a  
true “zero-clearance” effect and give you maximum benefit from your inserts.  
318600622  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Projection Television 17C487 User Manual
Greenheck Fan Smoke Alarm SMD 401M User Manual
Grizzly Biscuit Joiner G0725 User Manual
Hans Grohe Plumbing Product 40516XX0 User Manual
Hotpoint Oven S130E Mk2 User Manual
HP Hewlett Packard Camcorder CC330 User Manual
HP Hewlett Packard Security Camera XP256 User Manual
Huawei Router B160 User Manual
Hypercom Network Card IEN 100 User Manual
Hypertec Mouse KYBAC201R USBBLKHY User Manual