Repair
ProConnect
334599A
Displacement Pump
EN
For professional use only.
Models: 17C487, 17C488, 17C489, 17C721
Important Safety Instructions
Read all warnings and instructions in this manual and related manuals.
Be familiar with the controls and the proper usage of the equipment.
Save these instructions.
ti24850a
Use only genuine Graco replacement parts.
The use of non-Graco replacement parts may void warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this
equipment. The exclamation point symbol alerts you to a general warning and the hazard
symbols refer to procedure-specific risks. When these symbols appear in the body of this
manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols
and warnings not covered in this section may appear throughout the body of this manual
where applicable.
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help
prevent fire and explosion:
•
Do not spray flammable or combustible materials near an open flame or sources of ignition
such as cigarettes, motors, and electrical equipment.
•
Paint or solvent flowing through the equipment is able to result in static electricity. Static
electricity creates a risk of fire or explosion in the presence of paint or solvent fumes. All
parts of the spray system, including the pump, hose assembly, spray gun, and objects in
and around the spray area shall be properly grounded to protect against static discharge
and sparks. Use Graco conductive or grounded high-pressure airless paint sprayer hoses.
•
•
Verify that all containers and collection systems are grounded to prevent static discharge.
Do not use pail liners unless they are antistatic or conductive.
Connect to a grounded outlet and use grounded extensions cords. Do not use a 3-to-2
adapter.
•
•
•
•
Do not use a paint or a solvent containing halogenated hydrocarbons.
Do not spray flammable or combustible liquids in a confined area.
Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area.
Sprayer generates sparks. Keep pump assembly in a well ventilated area at least 20 feet
(6.1 m) from the spray area when spraying, flushing, cleaning, or servicing. Do not spray
pump assembly.
•
•
Do not smoke in the spray area or spray where sparks or flame is present.
Do not operate light switches, engines, or similar spark producing products in the spray
area.
•
•
Keep area clean and free of paint or solvent containers, rags, and other flammable
materials.
Know the contents of the paints and solvents being sprayed. Read all Safety Data Sheets
(SDS) and container labels provided with the paints and solvents. Follow the paint and
solvents manufacturer’s safety instructions.
•
Fire extinguisher equipment shall be present and working.
334599A
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
WARNING
SKIN INJECTION HAZARD
High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the
event that injection occurs, get immediate surgical treatment.
•
•
Do not aim the gun at, or spray any person or animal.
Keep hands and other body parts away from the discharge. For example, do not try to stop
leaks with any part of the body.
•
•
•
Always use the nozzle tip guard. Do not spray without nozzle tip guard in place.
Use Graco nozzle tips.
Usecautionwhencleaningandchangingnozzletips. Inthecasewherethenozzletipclogs
while spraying, follow the Pressure Relief Procedure for turning off the unit and relieving
the pressure before removing the nozzle tip to clean.
•
Equipment maintains pressure after power is shut off. Do not leave the equipment
energized or under pressure while unattended. Follow the Pressure Relief Procedure
when the equipment is unattended or not in use, and before servicing, cleaning, or
removing parts.
•
•
Check hoses and parts for signs of damage. Replace any damaged hoses or parts.
Thissystemiscapableofproducing3300psi. UseGracoreplacementpartsoraccessories
that are rated a minimum of 3300 psi.
•
Always engage the trigger lock when not spraying. Verify the trigger lock is functioning
properly.
•
•
Verify that all connections are secure before operating the unit.
Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the
controls.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can
cause serious chemical reaction and equipment rupture. Failure to follow this
warning can result in death, serious injury, or property damage.
•
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon
solvents or fluids containing such solvents.
•
•
Do not use chlorine bleach.
Many other fluids may contain chemicals that can react with aluminum. Contact your
material supplier for compatibility.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on
skin, inhaled, or swallowed.
•
•
Read SDSs to know the specific hazards of the fluids you are using.
Store hazardous fluid in approved containers, and dispose of it according to applicable
guidelines.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent
seriousinjury, includingeyeinjury, hearingloss, inhalationoftoxicfumes, andburns.
This protective equipment includes but is not limited to:
•
•
Protective eyewear, and hearing protection.
Respirators, protective clothing, and gloves as recommended by the fluid and solvent
manufacturer.
CALIFORNIA PROPOSITION 65
This product contains a chemical known to the State of California to cause cancer,
birth defects or other reproductive harm. Wash hands after handling.
4
334599A
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
Repair
1. Engage trigger lock.
Trigger Lock
Always engage the trigger lock when sprayer
is stopped to prevent the gun from being
triggered accidentally by hand or if dropped
or bumped.
ti24851a
2. Turn ON/OFF switch to OFF position.
Wait 7 seconds for power to dissipate.
ti24612a
ti24852a
Pressure Relief Procedure
3. Unplug power cord or shut engine off.
This equipment stays pressurized until
pressure is manually relieved. To help
prevent serious injury from pressurized
fluid, such as skin injection, splashed fluid
and moving parts, follow the Pressure
Relief Procedure whenever sprayer is
stopped and before sprayer is cleaned or
checked, and before equipment is
serviced.
ti24853a
4. Engage trigger lock.
5. Remove tip guard.
334599A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
6. Turn pressure control to lowest setting.
8. Engage trigger lock.
Disengage trigger lock.
ti24855a
ti24854a
7. Hold a metal part of the gun firmly to a
grounded metal pail. Trigger the gun to
relieve pressure.
9. Open any fluid drain valves in system.
Leave drain valves open until ready to
spray again.
ti24585a
ti24608a
6
334599A
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
3. Dissemble intake valve. Clean and
Dissemble Pump
1. Remove packing nut and throat
adjustment spacer. Retaining nuts are
not removable and not sold separately.
inspect. O-ring may require a pick for
removal.
NOTICE
If using a pick to remove the O-ring use care
to avoid damage to the machined surfaces.
Retaining
Nuts
ti24863a
ti24874a
2. Unscrew cylinder from intake valve.
ti24870a
334599A
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
4. Tap piston rod out of cylinder with a
hammer or flip over and tap piston rod
out against a bench.
Do not clean or wipe the piston valve
threads. Cleaning the piston valve
threads could destroy the special sealing
patch and cause the piston valve to come
loose during operation, causing a pump
burst and possible serious bodily injury.
5. Unscrew piston valve from piston rod.
ti24876a
ti24875a
8
334599A
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
6. Clean and inspect parts. (The piston
has a special thread locking/sealing
patch. Apply thread sealant to the
threads.
7. Remove and discard throat packing
and glands from the cylinder.
ti24880a
ti24877a
334599A
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
2. Install ball in piston rod. If thread seal-
ant is applied to piston valve threads,
ensure that none gets on the ball.
Assemble Pump
1. SoakleatherpackingsinSAE30Woilfor
one hour before assembly.
Leather
Packings
ti24891a
3. Torque to 27 ± 3 ft-lb (37 ± 4 N•m).
ti24890a
Leather
Packings
ti24892a
ti24893a
10
334599A
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
4. Assemble leather throat packings
soaked earlier.
6. Apply liberal amounts of grease or oil to
piston packings.
Leather
Packings
ti24895a
7. Grease top inch or two of piston rod
that will go through the cylinder throat
packings. Gently guide displacement
rod up through throat packings. Tap
bottom of piston valve as necessary
with a leather or plastic hammer.
ti24893a
5. Loosely install packing nut with o-ring
onto cylinder.
ti24896a
ti24894
334599A
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
8. Grease o-ring and place on outside
10. Torque to 60 ± 5 ft-lb (81 ± 7 N•m).
diameter ring groove.
ti24897a
9. Clean seat thoroughly. Reassemble
intake valve with a seat, ball, and new
o-ring. Seat may be flipped over and
used on other side.
ti24899a
ti24898a
12
334599A
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
11. Install o-ring onto packing nut. Torque
to 75 ± 5 ft-lb (101.7 ± 6.8 N•m) or addi-
tional 1/2 turn from hand tight.
12. Storage
ti24901a
ti24900a
334599A
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
When pump packings begin to leak after
much use, perform Pressure Relief
down until leakage stops or lessens. This
allows approximately 100 gallons of
additional operation before a repacking is
required. Packing nut can be tightened
without o-ring removal.
Throat Packing Adjustment
This equipment stays pressurized until
pressure is manually relieved. To help
prevent serious injury from pressurized
fluid, such as skin injection, splashed fluid
and moving parts, follow the Pressure
Relief Procedure whenever sprayer is
stopped and before sprayer is cleaned or
checked, and before equipment is
serviced.
ti24988a
14
334599A
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Parts List
Ref. Part
217* 15B112 PACKING, o-ring
(0.941 in. OD)
218* 105445 BALL, sst, 0.5000 in.
219* 108526 O-RING, PTFE
220* 160516 O-RING
221* 176755 V-PACKING, leather,
throat
Description
Qty.
Ref. Part
201 24W617 ROD, displacement,
includes 212
202* 180656 BUTTON, plug
203 193047 NUT, packing
204* 176757 GLAND, female, throat
205* 176754 GLAND, male throat
206 24W619 CYLINDER, pump
includes retaining
Description
Qty.
1
1
1
1
1
2
1
1
1
1
1
222* 192710 V-PACKING, throat,
3
TM
nuts 229
V-Max
207* 105444 BALL, sst, 0.3125 in.
208* 195129 GLAND, male piston
209* 180073 GLAND, female, piston
211* 15G234 GUIDE, piston
212 239937 VALVE, piston
(included with 201)
213 15C011 GUIDE, ball
215 246429 KIT, seat, carbide
includes 213, 217 and
1
1
1
1
1
UHMWPE, blue
223* 176749 V-PACKING, leather,
piston
2
3
224* 192712 V-PACKING, piston,
TM
V-Max
UHMWPE, blue
225 17C231 FITTING, pump, QD,
1/4 npt
1
1
1
229 NUTS, retaining, not sold separately
218
216 15B611 VALVE, intake housing
1
* - Also included in Kit 255204
- Also included in Kit 246429
16
334599A
Download from Www.Somanuals.com. All Manuals Search And Download.
Pump Installation
Pump Installation
Pump installation includes securingthe pump
and connecting to the fluid inlet and outlet.
1. Connect outlet hose to pump.
ti24087a
5. Use both hands to tighten pump retain-
ing nut.
ti24086a
2. Move pump displacement rod up or
down until it slides into the connecting
rod when the pump is slid into the drive
housing.
ti24088a
6. Use a hammer to turn pump retaining
nut an additional 1/8 to 1/6th turn or 45°
to 60°.
ti24085a
3. Slide pump all the way into drive hous-
ing.
1/8 1/6
-
ti24089a
7. Install suction hose.
ti25139a
4. Close pump rod cover. Make certain
that it is flush against drive housing.
ti24090a
334599A
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Technical Specifications
PC Displacement Pump
US
Metric
Maximum fluid working pressure
Inlet/Outlet Sizes
3300 psi
228 bar, 22.8 MPa
Fluid inlet size
1.0 in. diameter
1/4 in.
2.54 cm diameter
6.3 mm
Fluid outlet size
Wetted materials on all models
stainless steel, PTFE, leather, nylon, zinc-plated and
nickel-plated carbon steel, tungsten carbide, chrome
plating, UHMWPE, acetal, polyethylene, nylon
18
334599A
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing
its name to be free from defects in material and workmanship on the date of sale to the original purchaser
for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will,
for a period of twelve months from the date of sale, repair or replace any part of the equipment
determined by Graco to be defective. This warranty applies only when the equipment is installed,
operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction,
damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or
improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts.
Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco
equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper
design, manufacture, installation, operation or maintenance of structures, accessories, equipment or
materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an
authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco
will repair or replace free of charge any defective parts. The equipment will be returned to the original
purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material
or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of
parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY
OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above.
The buyer agrees that no other remedy (including, but not limited to, incidental or consequential
damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential
loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH
ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED
BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose,
etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with
reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from
Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other
goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or
otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents,
notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or
indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du
présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés,
donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures
concernées.
334599A
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the
nearest distributor.
All written and visual data contained in this document reflects the latest product information available at
the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 334599
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revision A, November 2014
Download from Www.Somanuals.com. All Manuals Search And Download.
|