Grizzly Saw G0716 User Manual

MODEL G0716

10" DRUM SANDER

OWNER'S MANUAL

WARNiNG: NO pORtiON Of thiS MANUAL MAy bE REpRODUcED iN ANy ShApE

OR fORM WithOUt thE WRittEN AppROvAL Of GRizzLy iNDUStRiAL, iNc.

(For ModEls MaNuFaCturEd siNCE 2/11) #ts13385 priNtEd iN ChiNa

Download from Www.Somanuals.com. All Manuals Search And Download.

table of contents

iNtRODUctiON............................................... 2

SEctiON 5: AccESSORiES......................... 28

Manual accuracy ........................................... 2

Contact info.................................................... 2

Machine description ...................................... 2

identification................................................... 3

Machine data sheet ...................................... 4

SEctiON 6: MAiNtENANcE......................... 29

schedule...................................................... 29

general Cleaning......................................... 29

Cleaning sandpaper .................................... 29

lubrication ................................................... 29

SEctiON 1: SAfEty....................................... 6

safety instructions for Machinery .................. 6

additional safety for drum sanders .............. 8

SEctiON 7: SERvicE ................................... 30

troubleshooting ........................................... 30

Conveyor Belt tension & tracking.............. 33

Belt tension............................................... 33

Belt tracking.............................................. 33

gib adjustment ............................................ 34

Conveyor Belt to drum alignment ............... 35

pressure roller adjustment......................... 36

adjusting Elevation stop.............................. 37

Conveyor Belt replacement........................ 38

SEctiON 2: pOWER SUppLy........................ 9

availability.................................................... 9

Full-load Current rating............................. 9

Circuit requirements................................... 9

grounding & plug requirements............... 10

Extension Cords ........................................ 10

SEctiON 3: SEtUp ....................................... 11

Needed for setup......................................... 11

unpacking.................................................... 11

inventory ...................................................... 12

hardware recognition Chart ....................... 13

site Considerations...................................... 14

assembly ..................................................... 15

dust Collection............................................. 18

power Connection........................................ 18

Connecting power ..................................... 18

disconnecting power................................. 18

test run ...................................................... 19

recommended adjustments........................ 19

SEctiON 8: WiRiNG...................................... 39

Wiring safety instructions............................ 39

g0716 Wiring diagram ................................ 40

SEctiON 9: pARtS....................................... 41

stand............................................................ 41

Conveyor...................................................... 42

Main ............................................................. 44

Machine labels............................................ 46

WARRANty AND REtURNS ........................ 49

SEctiON 4: OpERAtiONS ........................... 20

Basic Controls.............................................. 20

Workpiece inspection................................... 21

sandpaper ................................................... 21

selection.................................................... 21

replacement ............................................. 22

depth of Cut................................................. 25

Feed rate.................................................... 26

sanding tips................................................ 26

sanding operation....................................... 27

Download from Www.Somanuals.com. All Manuals Search And Download.

iNtRODUctiON

Manual Accuracy

contact info

We are proud to offer this manual with your new

machine! We've made every effort to be exact

with the instructions, specifications, drawings,

and photographs of the machine we used when

writing this manual. However, sometimes we still

make an occasional mistake.

We stand behind our machines. If you have

any questions or need help, use the information

below to contact us. Before contacting, please get

the serial number and manufacture date of your

machine. This will help us help you faster.

Grizzly Technical Support

1203 Lycoming Mall Circle

Muncy, PA 17756

Also, owing to our policy of continuous improve-

ment, your machine may not exactly match the

manual. If you find this to be the case, and the dif-

ference between the manual and machine leaves

you in doubt, check our website for the latest

manual update or call technical support for help.

Phone: (570) 546-9663

Email: [email protected]

We want your feedback on this manual. What did

you like about it? Where could it be improved?

Please take a few minutes to give us feedback.

Before calling, find the manufacture date of your

machine by looking at the date stamped into the

machine ID label (see below). This will help us

determine if the manual version you received

matches the manufacture date of your machine.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [email protected]

Machine Description

Manufacture Date

of Your Machine

the Model g0716 drum sander features a vari-

able speed conveyor belt that feeds the workpiece

into the rotating sanding drum. the amount of

material removal (depth of cut) is controlled by the

elevation handwheel with the aid of the elevation

pointer and scale.

For your convenience, we post all available man-

uals and manual updates for free on our website

at www.grizzly.com. Any updates to your model

of machine will be reflected in these documents

as soon as they are complete.

For easy mobility, the lifting handles and wheels

allow the sander to be moved where needed. the

efficient dust collection hood allows the sawdust

from the sanding operation to be removed by a

dust collector.

-2-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

identification

Elevation

handwheel

Elevation pointer

& scale

dust Collection

hood

sanding

Motor

Elevation

lock Knob

Conveyor

Motor

oN/oFF

switch

sanding drum

housing

Feed rate

dial

Conveyor

Belt

lifting

handle

Wheel

assembly

stand

figure 1. Model g0716 identification.

to reduce the risk of

serious injury when using

this machine, read and

understand this entire

manual before beginning

any operations.

-3-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Machine Data Sheet

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0716 10" DRUM SANDER

Product Dimensions:

Weight.............................................................................................................................................................. 159 lbs.

Width (side-to-side) x Depth (front-to-back) x Height........................................................ 28-3/8 x 23-1/4 x 47-1/4 in.

Footprint (Length x Width)............................................................................................................... 17-1/2 x 13-1/2 in.

Shipping Dimensions:

Type................................................................................................................................................... Wood Slat Crate

Content........................................................................................................................................................... Machine

Weight.............................................................................................................................................................. 221 lbs.

Length x Width x Height....................................................................................................................... 32 x 25 x 26 in.

Electrical:

Power Requirement........................................................................................................... 110V, Single-Phase, 60 Hz

Minimum Circuit Size.............................................................................................................................................. 15A

Switch................................................................................................................... Toggle Safety with Safety Lock Tab

Switch Voltage..................................................................................................................................................... 110V

Cord Length.......................................................................................................................................................... 10 ft.

Cord Gauge.................................................................................................................................................. 16 Gauge

Plug Included.......................................................................................................................................................... Yes

Included Plug Type.................................................................................................................................... NEMA 5-15

Motors:

Sanding

Type.................................................................................................................. TEFC Capacitor Start Induction

Horsepower.......................................................................................................................................... 1-1/2 HP

Voltage....................................................................................................................................................... 110V

Phase....................................................................................................................................................... Single

Amps......................................................................................................................................................... 10.5A

Speed................................................................................................................................................ 1725 RPM

Cycle......................................................................................................................................................... 60 Hz

Number of Speeds............................................................................................................................................ 1

Power Transfer ............................................................................................................................... Direct Drive

Bearings......................................................................................................................... Sealed and Lubricated

Conveyor

Type.............................................................................................................................................................. DC

Horsepower........................................................................................................................................... 1/10 HP

Voltage......................................................................................................................................................... 24V

Amps......................................................................................................................................................... 0.72A

Number of Speeds................................................................................................................................ Variable

Power Transfer .......................................................................................................................................... Gear

Bearings......................................................................................................................... Sealed and Lubricated

-4-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Specifications:

Operation Information

Maximum Board Width.............................................................................................................................. 10 in.

Maximum Board Thickness......................................................................................................................... 3 in.

Minimum Board Thickness....................................................................................................................... 1/4 in.

Minimum Board Length......................................................................................................................... 4-3/4 in.

Sanding Drums Speed....................................................................................................................... 2300 FPM

Conveyor Feed Rate......................................................................................................................... 0 - 10 FPM

Sanding Belt Length............................................................................................................................ 62-1/2 in.

Sanding Belt Width...................................................................................................................................... 3 in.

Drum Information

Infeed Sanding Drum Size............................................................................................................. 5-1/8 x 10 in.

Construction

Conveyor Belt......................................................................................................................................... Rubber

Body.................................................................................................................. Cast Iron, Steel, and Aluminum

Base........................................................................................................................................................... Steel

Paint......................................................................................................................... Powder Coated and Epoxy

Other Related Information

Floor To Belt Height............................................................................................................................. 27-1/8 in.

No Of Pressure Rollers..................................................................................................................................... 2

Conveyor Belt Length.......................................................................................................................... 41-1/4 in.

Conveyor Belt Width.................................................................................................................................. 10 in.

Belt Roller Size......................................................................................................................................... 3/4 in.

No Of Dust Ports.............................................................................................................................................. 1

Dust Port Size.............................................................................................................................................. 4 in.

Other Specifications:

ISO Factory .................................................................................................................................................. ISO 9001

Country Of Origin ............................................................................................................................................... China

Warranty ........................................................................................................................................................... 1 Year

Serial Number Location ........................................................................................................... ID Label on Headstock

Assembly Time ................................................................................................................................................. 1 Hour

Sound Rating ..................................................................................................................................................... 80 dB

Features:

Quick disconnect smooth sweep 90 degree 4 in. dust port

Variable speed conveyor

Wheels and handles for mobility

-5-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

SEctiON 1: SAfEty

For Your Own Safety, Read Instruction

Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.

This manual uses a series of symbols and signal words intended to convey the level of impor-

tance of the safety messages. The progression of symbols is described below. Remember that

safety messages by themselves do not eliminate danger and are not a substitute for proper

accident prevention measures.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

COULd result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert

against unsafe practices.

This symbol is used to alert the user to useful information about

proper operation of the machine.

NOTICE

Safety instructions for Machinery

OWNER’S MANUAL. Read and understand WEARING PROPER APPAREL. Do not wear

clothing, apparel, or jewelry that can become

entangled in moving parts. Always tie back or

cover long hair. Wear non-slip footwear to avoid

accidental slips which could cause a loss of work-

piece control.

this owner’s manual BEFORE using machine.

Untrained users can be seriously hurt.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating or

observing machinery to reduce the risk of eye

injury or blindness from flying particles. Everyday

eyeglasses are not approved safety glasses.

HEARING PROTECTION. Always wear hear-

ing protection when operating or observiing loud

machinery. Extended exposure to this noise

without hearing protection can cause permanent

hearing loss.

HAzARdOUS dUST. Dust created while using

machinery may cause cancer, birth defects, or

long-term respiratory damage. Be aware of dust

hazards associated with each workpiece material,

and always wear a NIOSH-approved respirator to

reduce your risk.

MENTAL ALERTNESS. Be mentally alert when

running machinery. Never operate under the

influence of drugs or alcohol, when tired, or when

distracted.

-6-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

DISCONNECTING POWER SUPPLY.-Always-dis- FORCING MACHINERY.-Do-not-force-machine.-

connect- machine- from- power- supply- before- ser- It-will-do-the-job-safer-and-better-at-the-rate-for-

vicing,- adjusting,- or- changing- cutting- tools- (bits,- which-it-was-designed.

blades,-cutters,-etc.).-Make-sure-switch-is-in-OFF-

position-before-reconnecting-to-avoid-an-unexpect-

ed-or-unintentional-start.

GUARDS & COVERS.- Guards- and- covers- can-

protect-you-from-accidental-contact-with-moving-

parts-or-flying-debris.-Make-sure-they-are- prop-

erly-installed,-undamaged,-and-working-correctly-

before-using-machine.

APPROVED OPERATION.- Untrained- operators-

can- be- seriously- hurt- by- machinery.- Only- allow-

trained- or- properly- supervised- people- to- use-

machine.-When-machine-is-not-being-used,-dis-

connect- power,- remove- switch- keys,- or- lock-out-

machine-to-prevent-unauthorized-use—especially-

around-children.-Make-workshop-kid-proof!

NEVER STAND ON MACHINE.-Serious-injury-or-

accidental-contact-with-cutting-tool-may-occur-if-

machine-is-tipped.-Machine-may-be-damaged.

STABLE MACHINE. Unexpected-movement-dur-

ing-operations-greatly-increases-the-risk-of-injury-

and- loss- of- control.- Verify- machines- are- stable/

secure- and- mobile- bases- (if- used)- are- locked-

before-starting.

DANGEROUS ENVIRONMENTS. Do- not- use-

machinery- in- wet- or- rainy- locations,- cluttered-

areas,-around-flammables,-or-in-poorly-lit-areas.-

Keep- work- area- clean,- dry,- and- well-lighted- to-

minimize-risk-of-injury.

AWKWARD POSITIONS.- Keep- proper- footing-

and-balance-at-all-times-when-operating-machine.-

Do-not-overreach!-Avoid-awkward-hand-positions-

that-make-workpiece-control-difficult-or-increase-

the-risk-of-accidental-injury.

ONLY USE AS INTENDED.- Only- use- machine-

for- its- intended- purpose.- Never- modify- or- alter-

machine-for-a-purpose-not-intended-by-the-manu-

facturer-or-serious-injury-may-result!

USE RECOMMENDED ACCESSORIES.-Consult-

this-owner’s-manual-or-the-manufacturer-for-rec-

ommended- accessories.- Using- improper- acces-

sories-will-increase-the-risk-of-serious-injury.

UNATTENDED OPERATION. Never- leave-

machine-running-while-unattended.-Turn-machine-

off-and-ensure-all-moving-parts-completely-stop-

before-walking-away.

CHILDREN & BYSTANDERS. Keep- children-

and-bystanders-a-safe-distance-away-from-work-

area.-Stop-using-machine-if-children-or-bystand-

ers-become-a-distraction.

MAINTAIN WITH CARE.-Follow-all-maintenance-

instructions- and- lubrication- schedules- to- keep-

machine-in-good-working-condition.-An-improperly-

maintained-machine-may-increase-the-risk-of-seri-

ous-injury.-

REMOVE ADJUSTING TOOLS.- Never- leave-

adjustment-tools,-chuck-keys,-wrenches,-etc.-in-or- CHECK DAMAGED PARTS.- Regularly- inspect-

on-machine—especially-near-moving-parts.-Verify- machine- for- damaged- parts,- loose- bolts,- mis-

adjusted- or- mis-aligned- parts,- binding,- or- any-

other- conditions- that- may- affect- safe- operation.-

Always-repair-or-replace-damaged-or-mis-adjust-

ed-parts-before-operating-machine.

removal-before-starting!

SECURING WORKPIECE.- When- required,- use-

clamps-or-vises-to-secure-workpiece.-A-secured-

workpiece-protects-hands-and-frees-both-of-them-

to-operate-the-machine.

EXPERIENCING DIFFICULTIES. If- at- any- time-

you- are- experiencing- difficulties- performing- the-

intended- operation,- stop- using- the- machine!-

Contact- our- Technical- Support- Department- at-

(570)-546-9663.

FEED DIRECTION.-Unless-otherwise-noted,-feed-

work- against- the- rotation- of- blades- or- cutters.-

Feeding-in-the-same-direction-of-rotation-may-pull-

your-hand-into-the-cut.

-7-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional Safety for Drum Sanders

KicKbAcK. Kickback is typically defined as the WORKpiEcE QUANtity. Never sand two or

high-speed expulsion of stock from the machine, more workpieces side-by-side. since workpieces

which can cause serious personal injury to the are never exactly the same thickness, one of them

operator or bystanders. until you have a clear may be thrown from the sander at a high rate of

understanding how kickback can occur, do Not speed and could cause serious personal injury.

operate this sander!

WORKpiEcE iNSpEctiON. Nails, staples,

WORKpiEcE fEED RAtE. taking too heavy of knots, or other imperfections in the workpiece

a cut or using too fast a feed rate can cause kick- can be dislodged and thrown from the sander at a

back. always use the correct depth of cut, then high rate of speed into the operator or bystanders.

firmly hold the workpiece on the conveyor and Never attempt to sand stock that has imperfec-

ease it into the sander at the same feed rate as tions or embedded foreign objects.

the conveyor belt.

DEpth Of cUt. this sander is designed to sand

AvOiDiNG ENtANGLEMENt. Becoming entan- a ⁄32" depth of cut or less. attempting to take a

gled in the moving parts of this machine can greater depth of cut could cause kickback or dam-

cause pinching and crushing injuries. to avoid age to the machine.

these hazards, do Not wear loose clothing,

gloves, or jewelry, and tie back long hair. Keep all WORKpiEcE DiMENSiONS. to maintain a sta-

guards in place and secure.

ble operation and avoid kickback, do not attempt

to sand workpieces shorter than 4³⁄4" or narrower

hAND pLAcEMENt. the rotating sanding drum than ³⁄4".

can remove a large amount of flesh in a few sec-

onds. always keep hands away from the sanding WORKpiEcEMAtERiAL.thissanderisdesigned

drum during operation. avoid pinching injuries by to sand only natural wood products or man-made

never putting your hand between the workpiece products made from natural wood fiber.

and the conveyor.

ALLERGic REActiONS. the dust from some

WORKpiEcE SUppORt. if not properly sup- wood species can cause harmful reactions to eyes

ported, long workpieces could bind with the sand- and lungs. always be aware of these hazards and

ing drum and cause kickback. always make sure take precautions by wearing personal protective

workpieces are properly supported on the infeed gear, such as safety goggles and respirator.

and outfeed sides of the sander.

bODy pLAcEMENt. in case of kickback, avoid

personal injury by always keeping your body to

the side of the sanding path.

No list of safety guidelines can be complete.

Every shop environment is different. Always

consider safety first, as it applies to your

individual working conditions. Use this and

other machinery with caution and respect.

failure to do so could result in serious per-

sonal injury, damage to equipment, or poor

work results.

Like all machinery there is potential danger

when operating this machine. Accidents are

frequently caused by lack of familiarity or

failure to pay attention. Use this machine

with respect and caution to decrease the

risk of operator injury. if normal safety pre-

cautions are overlooked or ignored, serious

personal injury may occur.

-8-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

SEctiON 2: pOWER SUppLy

Availability

circuit Requirements

This machine is prewired to operate on a 110V

power supply circuit that has a verified ground and

meets the following requirements:

Before installing the machine, consider the avail-

ability and proximity of the required power supply

circuit. If an existing circuit does not meet the

requirements for this machine, a new circuit must

be installed. To minimize the risk of electrocu-

tion, fire, or equipment damage, installation work

and electrical wiring must be done by a qualified

electrician in accordance with all applicable codes

and standards.

Nominal voltage ...............................110v/120v

cycle..........................................................60 hz

phase........................................... Single-phase

Minimum circuit Size......................... 15 Amps

A power supply circuit includes all electrical

equipment between the main breaker box or fuse

panel in your building and the incoming power

connections inside the machine. This circuit must

be safely sized to handle the full-load current that

may be drawn from the machine for an extended

period of time.

Electrocution, fire, or

equipment damage may

occur if machine is not

correctly grounded and

connected to the power

supply.

For your own safety and protection of

property, consult a qualified electrician if

you are unsure about wiring practices or

electrical codes in your area.

full-Load current Rating

The full-load current rating is the amperage a

machine draws at 100% of the rated output power.

On machines with multiple motors, this is the

amperage drawn by the largest motor or sum of all

motors and electrical devices that might operate

at one time during normal operations.

Note: The circuit requirements listed in this man-

ual apply to a dedicated circuit—where only one

machine will be running at a time. If this machine

will be connected to a shared circuit where mul-

tiple machines will be running at the same time,

consult a qualified electrician to ensure that the

circuit is properly sized for safe operation.

full-Load current Rating at 110v... 11.2 Amps

The full-load current is not the maximum amount

of amps that the machine will draw. If the machine

is overloaded, it will draw additional amps beyond

the full-load rating.

If the machine is overloaded for a sufficient length

of time, damage, overheating, or fire may result—

especially if connected to an undersized circuit.

To reduce the risk of these hazards, avoid over-

loading the machine during operation and make

sure it is connected to a power supply circuit that

meets the requirements in the following section.

-9-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Improper connection of the equipment-grounding

wire can result in a risk of electric shock. The

wire with green insulation (with or without yellow

stripes) is the equipment-grounding wire. If repair

or replacement of the power cord or plug is nec-

essary, do not connect the equipment-grounding

wire to a live (current carrying) terminal.

Grounding & plug Requirements

This machine MUST be grounded. In the event

of certain malfunctions or breakdowns, grounding

reduces the risk of electric shock by providing a

path of least resistance for electric current.

This machine is equipped with a power cord that

has an equipment-grounding wire and a ground-

ing plug (similar to the figure below). The plug

must only be inserted into a matching receptacle

(outlet) that is properly installed and grounded in

accordance with all local codes and ordinances.

Check with a qualified electrician or service per-

sonnel if you do not understand these grounding

requirements, or if you are in doubt about whether

the tool is properly grounded. If you ever notice

that a cord or plug is damaged or worn, discon-

nect it from power, and immediately replace it with

a new one.

Serious injury could occur if you connect

the machine to power before completing the

setup process. DO NOT connect to power

until instructed later in this manual.

Extension cords

We do not recommend using an extension cord

with this machine. If you must use an extension

cord, only use it if absolutely necessary and only

on a temporary basis.

GROUNDED

Extension cords cause voltage drop, which may

damage electrical components and shorten motor

life. Voltage drop increases as the extension cord

size gets longer and the gauge size gets smaller

(higher gauge numbers indicate smaller sizes).

5-15 RECEPTACLE

Grounding Prong

Any extension cord used with this machine must

contain a ground wire, match the required plug

and receptacle, and meet the following require-

ments:

5-15 PLUG

Neutral Hot

figure 2. typical 5-15 plug and receptacle.

Minimum Gauge Size...........................14 AWG

Maximum Length (Shorter is better).......50 ft.

SHOCK HAZARD!

Two-prong outlets do not meet the grounding

requirements for this machine. Do not modify

or use an adapter on the plug provided—if

it will not fit the outlet, have a qualified

electrician install the proper outlet with a

verified ground.

-10-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

SEctiON 3: SEtUp

Needed for Setup

this machine presents

serious injury hazards

to untrained users. Read

through this entire manu-

al to become familiar with

the controls and opera-

tions before starting the

machine!

the following are needed to complete the setup

process, but are not included with your machine.

Description

Qty

•

safety glasses ........................................... 1

additional people (for lifting) ...................... 1

phillips screwdriver #2............................... 1

Wrench/socket 10mm ................................ 1

Wrench/socket 13mm ................................ 2

Wrench/socket 16mm ................................ 2

Needle-Nose pliers .................................... 1

dust Collection system.............................. 1

dust hose 4" .............................................. 1

hose Clamps 4" ......................................... 2

Wear safety glasses dur-

ing the entire setup pro-

cess!

this machine and its com-

ponents are very heavy.

Get lifting help or use

power lifting equipment

such as a forklift to move

heavy items.

Unpacking

your machine was carefully packaged for safe

transportation. remove the packaging materials

from around your machine and inspect it. if you

discover the machine is damaged, please imme-

diately call Customer Service at (570) 546-9663

for advice.

save the containers and all packing materials for

possible inspection by the carrier or its agent.

Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi-

tion of your shipment, inventory the contents.

SUFFOCATION HAZARD!

Keep children and pets away

from plastic bags or packing

materials unpacked with this

machine. Discard immediately.

-11-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

inventory

The following is a description of the main compo-

nents shipped with your machine. Lay the compo-

nents out to inventory them.

If any non-proprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

inventory: (figure 3)

Qty

A. drum sander assembly (Not shown) ........ 1

b. left/right long top Braces 23¹⁄8".............. 2

c. Wheels 4" ................................................... 2

D. legs............................................................ 4

E. long Bottom Braces 20¹⁄4" ......................... 2

f. Elevation handwheel handle ..................... 1

G. leg Foot pads............................................ 4

h. Wheel axle................................................. 1

i. dust Collection 90° Elbow 4" ..................... 1

J. lifting handle assemblies.......................... 2

K. left/right Wheel Brackets.................1 Each

L. left/right short top Braces 14⁵⁄8" ............. 2

M. short Bottom Braces 17¹⁄4"......................... 2

N. hardware (Not shown)

figure 3. small component inventory.

NOTICE

If you cannot find an item on this list, check

the mounting location on the machine or the

packaging materials. Sometimes parts are

pre-installed for shipping, or they become

hidden by packaging materials.

—Carriage Bolts M8-1.25 x 12 (stand) .... 32

—lock Nuts M8-1.25 (stand)................... 32

—Cotter pins 4 x 20mm (Wheels).............. 2

—hex Bolts M8-1.25 x 16 (Wheels) ........... 4

—lock Nuts M8-1.25 (Wheels) .................. 4

—Flat head screws M6-1 x 10 (handles).. 4

—lock Nuts M6-1 (handles)...................... 4

—hex Bolts M10-1.5 x 30 (sander)............ 4

—Flat Washer 10mm (sander)................... 4

—hex Nuts M10-1.5 (sander)..................... 4

-12-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

hardware Recognition chart

-13-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Site considerations

Weight Load

Physical Environment

Refer to the Machine Data Sheet for the weight

of your machine. Make sure that the surface upon

which the machine is placed will bear the weight

of the machine, additional equipment that may be

installed on the machine, and the heaviest work-

piece that will be used. Additionally, consider the

weight of the operator and any dynamic loading

that may occur when operating the machine.

The physical environment where your machine

is operated is important for safe operation and

the longevity of its components. For best results,

operate this machine in a dry environment that is

free from excessive moisture, hazardous chemi-

cals, airborne abrasives, or extreme conditions.

Extreme conditions for this type of machinery are

generally those where the ambient temperature

range exceeds 41°–104°F; the relative humidity

range exceeds 20–95% (non-condensing); or the

environment is subject to vibration, shocks, or

bumps.

Space Allocation

Consider the largest size of workpiece that will

be processed through this machine and provide

enough space around the machine for adequate

operator material handling or the installation of

auxiliary equipment. With permanent installations,

leave enough space around the machine to open

or remove doors/covers as required by the main-

tenance and service described in this manual.

See below for required space allocation.

Electrical Installation

Place this machine near an existing power source.

Make sure all power cords are protected from

traffic, material handling, moisture, chemicals,

or other hazards. Make sure to leave access to

a means of disconnecting the power source or

engaging a lockout/tagout device.

Lighting

Children or untrained people

may be seriously injured by

this machine. Only install in an

access restricted location.

Lighting around the machine must be adequate

enough that operations can be performed safely.

Shadows, glare, or strobe effects that may distract

or impede the operator must be eliminated.

Power Connection

Infeed Clearance

30"

Outfeed Clearance

23"

figure 4. Minimum working clearances.

-14-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Assembly

x 16

When assembling the stand for this drum sander,

it is important that each part of the stand is ori-

ented and attached in a specific way. refer to the

illustration in figure 6 below to gain a clear under-

standing of the layout for each leg and brace.

Note: The parts illustrated are displayed "upside

down", as they will be during the assembly steps.

to assemble the drum sander:

figure 5. legs attached to the top braces.

1. position the top braces upside down on a

protected surface in the form of a rectangle,

then attach the legs to the braces with (16)

M8-1.25 x 12 carriage bolts and M8-1.25 lock

nuts, as shown in figure 5. hand tighten all

fasteners for now. they will be fully tightened

in Step 4.

REAR

Mounting Holes

for Wheel Brackets

Step 1

Step 2

Short Bottom Brace

Short Top Brace

Oblong Mounting

Holes

Short Top Brace

Mounting Holes

for Lifting Handles

Short Bottom Brace

FRONT

figure 6. layout and orientation of the stand legs and braces.

-15-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

2. attach the bottom braces to the legs, as

shown in figure 7, with the remaining (16)

M8-1.25 x 12 carriage bolts and M8-1.25 lock

nuts.

5. attach the wheel brackets to the rear legs

with (4) M8-1.25 x 16 hex bolts and M8-1.25

lock nuts (see figure 9).

Note: The left and right wheel brackets are

different configurations.

x 4

x 16

Cotter pin

figure 7. Bottom braces attached to the legs.

figure 9. Wheels assemblies.

3. slide the leg foot pads onto the bottom of the

legs, as shown in figure 8.

6. slide the wheel axle through the brackets, put

the wheels onto the ends of the axle, then

secure them with the cotter pins by inserting

them through the axle holes and bending

back the ends.

7. attach the lifting handle assemblies on the

front legs with (4) M6-1 x 10 flat head screws

and M6-1 lock nuts, as shown in figure 10.

Foot

pad

x 4

figure 8. leg foot pad installed.

4. Carefully turn the stand over, square up the

legs and braces, then fully tighten all fasten-

ers.

figure 10. lifting handle assemblies attached.

-16-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

8. With the help of another person for lifting,

place the sander assembly on the stand,

align the mounting holes, then secure it in

place with (4) M10-1.5 x 30 hex bolts, 10mm

flat washers, and M10-1.5 hex nuts (see

figure 11).

Elevation

handwheel

Note: If necessary to align the mounting

holes, slightly loosen the stand fasteners.

Be sure to re-tighten them after securing the

sander assembly.

figure 12. handle installed onto the elevation

handwheel.

10. install the dust collection elbow into the dust

collection hood, as shown in figure 13.

x 4

Elbow

figure 11. sander assembly secured to the

stand.

9. thread the handle into the elevation

handwheel, as shown in figure 12.

figure 13. dust collection elbow installed.

-17-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Dust collection

power connection

Before the machine can be connected to the

power source, an electrical circuit and connec-

tion device must be prepared per the pOWER

SUppLy section in this manual, and all previ-

ous setup instructions in this manual must be

complete to ensure that the machine has been

assembled and installed properly.

DO NOt operate the Model G0716 without an

adequate dust collection system. this sand-

er creates substantial amounts of wood dust

while operating. failure to use a dust collec-

tion system can result in short and long-term

respiratory illness.

always makesurethepower switch onthemachine

is turned oFF (or the oFF button is pushed in)

before connecting/disconnecting power.

Recommended cfM at Dust port: 400 cfM

Do not confuse this CFM recommendation with

the rating of the dust collector. To determine the

CFM at the dust port, you must consider these

variables: (1) CFM rating of the dust collector,

(2) hose type and length between the dust col-

lector and the machine, (3) number of branches

or wyes, and (4) amount of other open lines

throughout the system. Explaining how to cal-

culate these variables is beyond the scope of

this manual. Consult an expert or purchase a

good dust collection "how-to" book.

connecting power

insert the power cord plug into a matching power

supply receptacle. the machine is now connected

to the power source.

Disconnecting power

if you need to disconnect the machine from power

later, pull the plug completely out of the recep-

tacle. Make sure to grasp the plug when pulling it

from the receptacle—do not pull on the cord or it

could become damaged.

to connect a dust collection hose:

1. Fit the 4" dust hose over the dust collection

elbow, as shown in figure 14, and secure in

place with a hose clamp.

2. tug the hose to make sure it does not come

off. Note: A tight fit is necessary for proper

performance.

figure 14. dust hose attached to dust port.

-18-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

test Run

once the assembly is complete, test run your

machine to make sure it runs properly and is

ready for regular operation.

the test run consists of verifying the following:

1) Both motors power up and run correctly, and

2) the safety disabling mechanism on the switch

works correctly.

figure 15. removing switch key from paddle

switch.

if, during the test run, you cannot easily locate

the source of an unusual noise or vibration, stop

using the machine immediately, then review

troubleshooting on page 30.

8. try to turn the start the machine with the

paddle switch.

—if the machine does not start, the switch

disabling feature is working as designed.

to test run the machine:

1. Make sure you have read the safety instruc-

tions at the beginning of the manual and that

the machine is setup properly.

—if the machine starts, immediately stop the

machine. the switch disabling feature is

not working correctly. this safety feature

must work properly before proceeding with

regular operations. Call tech support for

help.

2. Make sure all tools and objects used during

setup are cleared away from the machine.

3. Make sure the sanding drum is safely above

the conveyor belt so that it will not make con-

tact when running.

Recommended

Adjustments

4. Verify that the machine is operating correctly

by turning it ON.

—When operating correctly, the machine

runs smoothly with little or no vibration or

rubbing noises.

For your convenience, the adjustments listed

below have been performed at the factory.

however, because of the many variables involved

with shipping, we recommend that you at least

verify the following adjustments to ensure the best

possible results from your new machine.

—investigate and correct strange or unusual

noises or vibrations before operating the

machine further. always disconnect the

machine from power when investigating or

correcting potential problems.

step-by-step instructions for these adjustments

can be found on the referenced page for each

item.

5. rotate the conveyor variable feed rate dial

clockwise to verify the conveyor belt feed rate

changes, then turn it counterclockwise until

the belt stops.

factory adjustments that should be verified:

•

Conveyor belt tension and tracking

(page 33)

6. turn the machine OFF.

•

gib adjustment (page 34)

7. remove the switch disabling key, as shown

in figure 15.

Conveyor belt to drum alignment (page 35)

pressure roller adjustment (page 36)

adjusting elevation stop (page 37)

-19-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

SEctiON 4: OpERAtiONS

basic controls

to reduce the risk of

serious injury when using

this machine, read and

understand this entire

manual before beginning

any operations.

refer to figure 16 and the descriptions below to

better understand the basic controls used when

sanding.

Damage to your eyes and lungs could result

from using this machine without proper pro-

tective gear. Always wear safety glasses and

a respirator when operating this machine.

figure 16. Basic controls.

A. Elevation Lock Knob: secures the sanding

head in place after adjusting the elevation.

additionally, this lock helps keep the sand-

ing drum parallel to the conveyor belt during

operation.

Loose hair, clothing, or

jewelry could get caught

in machinery and cause

serious personal injury.

Keep these items away

from moving parts at all

times to reduce this risk.

b. Elevation handwheel: adjusts the height of

the sanding drum above the conveyor belt to

control the depth of cut or accommodate new

workpieces.

NOTICE

c. pointer & Elevation Scale: displays the

current height of the sanding drum above the

conveyor belt in inches and millimeters.

if you have never used this type of machine

or equipment before, WE StRONGLy REc-

OMMEND that you read books, review

industry trade magazines, or get formal

training before beginning any projects.

Regardless of the content in this section,

Grizzly industrial will not be held liable for

accidents caused by lack of training.

D. ON/Off Switch: Controls power flow to the

sanding and conveyor motors. this switch

can be disabled for safety by removing the

key.

E. conveyor variable feed Rate Dial: adjusts

the feed rate of the conveyor belt from 0 to 10

FpM (Feet per Minute).

f. Lifting handles: provides a method to lift

and move the machine.

-20-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Workpiece

inspection

Sandpaper

Selection

sanding a workpiece smooth requires making

progressively smaller scratches in the wood until

they become too small to feel or be seen.

some workpieces are not safe to sand or may

require modification before they are safe to sand.

before sanding, inspect all workpieces for the

following:

the abrasiveness of sandpaper is designated

in grit size—the larger the number, the finer the

abrasive and the smaller the scratches. thus, 100

grit is finer than 60 grit.

•

Material Type: this machine is intended for

sanding natural and man-made wood prod-

ucts. this machine is Not designed to sand

metal, glass, stone, tile, etc.; sanding these

materials with a drum sander saw may lead

to injury.

typically, sanding operations start with a coarse

grit and progressively work through the finer

(larger number) grits until the desired finish is

achieved. avoid skipping a grit to achieve the best

results. Choosing which grit to start and finish with

depends on many factors, such as the workpiece

condition, type and hardness of wood, the desired

finish, and others.

•

Foreign Objects: Nails, staples, dirt, rocks

and other foreign objects are often embed-

ded in wood. While sanding, these objects

can become dislodged and hit the operator,

cause kickback, or damage the machine.

always visually inspect your workpiece for

these items. if they can't be removed, do

Not cut the workpiece.

there are many types of sanding belts to choose

from. We recommend aluminum oxide for gen-

eral workshop environments. Below is a chart that

groups abrasives into different classes and shows

which grits fall into each class.

•

Large/Loose Knots: loose knots can

become dislodged during the sanding opera-

tion. large knots can cause kickback and

machine damage. Choose workpieces that

do not have large/loose knots.

Grit

class

Usage

Extra Coarse rough sawn boards,

thickness sanding,

Wet or "Green" Stock: sanding wood with

a moisture content over 20% causes unnec-

essary wear on the sandpaper and motors,

increases the risk of kickback, and yields

poor results.

and glue removal.

Coarse

thickness sanding

and glue removal.

80–100 Medium

120–180 Fine

removing

marks and initial fin-

ish sanding.

planer

Excessive Warping: Workpieces with exces-

sive cupping, bowing, or twisting are danger-

ous to cut because they are unstable and

often unpredictable when being cut. do Not

use workpieces with these characteristics!

Finish sanding.

NOTICE

Sanding workpieces with high-resin con-

tent or with applied finishes can quickly

contaminate the sandpaper beyond the

point where it can be properly cleaned. this

will produce poor sanding results. in this

case, use a different workpiece, remove

the applied finishes, or frequently clean/

replace the sandpaper strip.

Minor Warping: Workpieces with slight cup-

ping can be safely supported if the cupped

side is facing the conveyor belt. on the con-

trary, a workpiece supported on the bowed

side will rock during a cut and could cause

kickback or severe injury.

-21-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

the proper installation of the sandpaper strip on

the drum is essential to ensure good sanding

results and prevent the sandpaper from coming

loose or tearing during operation.

Replacement

replacement sandpaper for the Model g0716 is

available in 3" bulk rolls (see page 28 for options

from grizzly).

items Needed

hex Wrench 5mm.............................................. 1

replacement sandpaper strip .......................... 1

Qty

When fabricating a replacement sandpaper strip

from bulk rolls, either use the existing strip as a

template or refer to the dimensioning information

in figure 17.

to replace the sandpaper strip:

1. disCoNNECt saNdEr FroM poWEr!

2. remove the cap screw that secures the

dust collection hood, then swing it up to gain

access to the sanding drum.

2¹/2

Remove The

Gray Areas

On Both Ends

3. reach under the right lip of the drum and

push the clamping device so that the jaw is

aligned with the slot in the drum surface (see

figure 18).

65¹/2

Full

Length

Before

Removing

End

15³/4

At an

Angle

Pieces

15³/4

At an

Angle

Clamping

device

figure 18. aligning right clamping device jaw

with the drum slot.

2¹/2

figure 17. replacement sandpaper dimensions.

Tip: To get two strips from a 10 ft. roll, cut the roll in the middle at an

angled as shown here.

-22-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

4. unwind the sandpaper strip from the drum

until you reach the clamping device on the

left side (see figure 19).

8. While keeping reasonable tension on the

strip with one hand, roll the drum away from

you with the other hand to wrap the strip onto

the drum (see figure 20).

important: When wrapping the strip onto

the drum, a minimum ⁄8" gap between the

edges may be necessary, but do not overlap.

Additionally, make sure that the strip remains

tight without any slack.

Clamping

device

figure 19. releasing the clamping device on the

left side of the drum.

5. reach under the left drum lip and lift up on

the clamping device to release its grip on the

sandpaper, then remove the sandpaper.

figure 20. Wrapping sandpaper strip on the

drum.

6. lift up on the same clamping device from

Step 5, then insert the end of the replace-

ment strip so that it fills as much of the slot

as possible and is aligned with the left side of

the slot.

9. to secure the right end of the strip, move the

clamping device forward by pressing against

the spring lever until you can insert the hold-

ing pin between clamp and the spring lever,

as shown in figure 21.

7. release the clamping device to hold the strip

in place, then tug on it to make sure it is

secure.

holding

—if the strip comes loose when you tug on

it with reasonable force, repeat Steps 5–6

until it is properly secure.

Clamp

spring

lever

if the sandpaper strip comes loose during

operation, it could cause the workpiece to

bind and kickback at the operator, which

could result in serious personal injury.

Always make sure the sandpaper strip is

properly installed and firmly secured by the

clamping devices before connecting the

sander to power.

figure 21. holding pin inserted into the access

hole (viewed from the right side of drum).

-23-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

10. press the spring lever toward the clamp to

open it, then fully insert the end of the sand-

paper strip between the two sides of the

clamp, as shown in figure 22.

removing

important. Make sure that the sandpaper

end goes inside the clamp—not between the

spring lever and the clamp.

spring lever

released

Maintaining

pressure

on Clamp

figure 23. properly securing the sandpaper end.

13. Check to make sure the sandpaper strip is

tight against the drum, the edges are not

the sandpaper

goes here.

more than ⁄8" apart, and they are not over-

lapped.

—if any of the conditions above are not true,

repeat the installation procedure until they

are.

figure 22. inserting the sandpaper end between

the two sides of the clamp.

14. Close and secure the dust collection hood

with the cap screw before connecting the

sander to power.

11. release the spring lever—this will allow the

clamp to grab the sandpaper end.

12. While maintaining pressure on the clamp with

your finger as shown in figure 23, remove

the holding pin. then, release the clamp—

this will pull the sandpaper tight.

-24-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

to adjust the depth of cut:

Depth of cut

1. loosen the elevation lock knob (see

figure 24).

the correct depth of cut when surface sanding

with the Model g0716 depends on many vari-

ables, such as the hardness of the wood, the

width of the workpiece, and the feed rate.

handwheel

generally, a ⁄4 turn of the elevation handwheel

(¹⁄32" depth of cut) per pass is acceptable for

coarser grits or softer woods. a ⁄8 turn of the

handwheel (¹⁄64" depth of cut) is recommended

for finer grits or harder woods. however, use your

best judgement to produce good sanding results

for your operation.

lock

Knob

important: Keep in mind that, although the thick-

ness of the workpiece is reduced during sanding,

this process is not a replacement for thickness

planing, which should be done with a planer or

other acceptable tool/machine before beginning

the sanding process.

pointer & scale

figure 24. Elevation controls.

2. rotate the elevation handwheel counter-

clockwise to lower the sanding drum.

Note: a ¹⁄4 turn of the handwheel equals ¹⁄32"

depth of cut.

NOTICE

taking an excessive depth of cut could

cause the sanding motor to exceed the

available power source amperage. in this

case, the motor or power source circuit

breaker will trip. if this should happen, dis-

connect the machine from power, allow the

motor to cool, reset the circuit breaker, then

take a smaller depth of cut.

3. When you have set the proper depth of cut

for your operation, firmly tighten the lock knob

to secure the sanding drum in place above

the workpiece.

NOTICE

it is imperative that the elevation lock knob

is fully tightened before resuming the sand-

ing process. Otherwise, the sanding drum

will raise up under the pressure from the

workpiece and will not evenly sand it.

-25-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

feed Rate

Sanding tips

setting the proper feed rate is a matter of experi-

ence and good judgement. When selecting the

feed rate for the operation, consider variables

such as the hardness and condition of the wood,

the sandpaper grit being used, the finish desired,

etc.

Follow these precautions to ensure safe sanding

operation and quality results:

•

replace the sandpaper with a higher grit to

achieve a finer finish (refer to Sandpaper on

page 21).

as a guideline, wide or hard workpieces, or using

finer grit sandpaper will require a slower feed rate.

the goal in setting the correct feed rate is to pro-

duce the desired results for the operation without

burning the workpiece.

•

When making multiple passes on the

workpiece, do not lower the sanding drum

more than ⁄32" or ⁄4 turn of the elevation

handwheel for any one pass.

•

if possible, feed the workpiece at a 60° angle

to the sanding drum. this will provide for

more effective material removal, less loading

and more even wear of the sandpaper, and

lighter load on the motors. on the last finish-

ing passes, feed the workpiece so that the

majority of the grain is perpendicular to the

sanding drum.

NOTICE

Using too fast of a feed rate may exceed the

sanding motor capacity and trip the motor

or power supply circuit breaker. Using too

slow of a feed rate may burn the surface of

the workpiece.

•

Extend the life of the sandpaper by regularly

using a pro-stiCK© sanding pad (refer to

Accessories on page 28).

to adjust the conveyor belt feed rate, rotate

the conveyor variable feed rate dial shown in

figure 25.

reduce snipe when sanding more than one

board of the same thickness by feeding them

into the sander with the front end of the sec-

ond board touching the back end of the first

board.

Feed rate

dial

•

do Not edge sand boards. this can cause

boards to kickback, causing serious personal

injury. Edge sanding boards also can cause

damage to the conveyor belt and sandpa-

per.

When sanding workpieces with a bow or

crown, place the high point up (prevents the

workpiece from rocking) and take very light

passes.

figure 25. location of the feed rate dial.

Note: The ON/OFF switch must be in the ON

position to enable the conveyor motor to run.

-26-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

8. When the sanding drum has complete con-

trol of the workpiece, step to the rear of the

sander, and maintain control and support of

the workpiece as it leaves the sanding drum

on its own.

Sanding Operation

to surface sand a workpiece:

1. Make sure the sander is turned OFF and the

sanding drum is completely stopped.

9. Without changing the depth-of-cut setting,

rotate the workpiece 180° horizontally and

pass it through the sander again.

2. Make sure that the correct sandpaper grit is

properly installed on the drum.

Note: If fine thickness dimensioning or main-

taining the same finishes on both sides of

the workpiece is required for the operation,

flip the workpiece over, lower the sanding

drum the correct amount, and repeat Steps

7–9. Return the workpiece to its original side

before continuing with the next step.

3. inspect the workpiece and make sure it is

acceptable for the sanding operation (refer

to Workpiece inspection on page 21 for

details).

4. place the workpiece flat on the conveyor belt

and under the sanding drum.

10. increase the depth of cut by the correct

amount, then repeat Steps 7–10 with pro-

gressively finer grits until you have produced

the desired results.

5. lower the sanding drum until it matches the

greatest height of the workpiece.

Note: Make this adjustment so that the first

passes will take off just the high spots of the

workpiece.

Note: Keep in mind that as the grit and

desired finish change, you need to reduce the

feed rate.

6. remove the workpiece from the conveyor

belt, then turn the sander ON and adjust the

conveyor feed rate so that it is correct for the

operation.

11. When the sanding operation is complete, turn

the sander OFF.

7. stand to the left of the conveyor belt to avoid

the hazards of kickback, place it on the con-

veyor belt at the correct angle, then allow the

belt to feed it under the sanding drum.

-27-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

aCCEssoriEs

SEctiON 5: AccESSORiES

3" x 10 ft. Aluminum Oxide Sanding Rolls

G3071—60 Grit

G3072—80 Grit

G3073—100 Grit

G3074—120 Grit

G4400—150 Grit

G4401—180 Grit

G4402—220 Grit

Some aftermarket accessories can be

installed on this machine that could cause

it to function improperly, increasing the risk

of serious personal injury. to minimize this

risk, only install accessories recommended

for this machine by Grizzly.

NOTICE

Refer to the newest copy of the Grizzly

catalog for other accessories available for

this machine.

G1512—pro-Stik® Sandpaper cleaner pad

this crepe-rubber sandpaper Cleaner quickly

removes gum and grit from sandpaper strips

without damage. Just run the cleaner through the

sander several times along the length of the sand-

ing drum until it is clean. Extend the life of your

sandpaper with this innovative natural cleaner.

figure 27. 3" x 10 ft. sandpaper rolls.

h2499—Small half-Mask Respirator

h3631—Medium half-Mask Respirator

h3632—Large half-Mask Respirator

h3635—cartridge filter pair p100

Wood dust has been linked to nasal cancer and

severe respiratory illnesses. if you work around

dust everyday, a half-mask respirator can be a

lifesaver. also compatible with safety glasses!

figure 26. g1512 pro-stik^®Belt Cleaner.

figure 28. half-mask respirator with disposable

cartridge filters.

-28-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

SEctiON 6: MAiNtENANcE

Lubrication

Always disconnect power

to the machine before

performing maintenance.

failure to do this may

result in serious person-

the bearings on the Model g0716 have been

lubricated and sealed at the factory. No other care

of these bearings is necessary unless they need

replacement.

al injury.

periodically, depending upon usage, clean away

and sawdust or grime from the elevation leadscrew

and the sanding head slides (see figure 29), then

apply a small amount of dry lubricant, such as

graphite. Move the sanding head through its full

Schedule

For optimum performance from your machine,

follow this maintenance schedule and refer to any

specific instructions given in this section.

range of motion to distribute the lubricant.

Note: Do not use grease or oil lubricants that will

attract and hold the sawdust.

Daily check

•

loose mounting bolts.

damaged, worn, or loaded sandpaper.

Worn or damaged wires or switches.

Worn or damaged conveyor belt.

any other unsafe condition.

leadscrew

General cleaning

slide

(1 of 2)

Cleaning the Model g0716 is relatively easy.

Vacuum excess wood chips and sawdust, and

wipe off the remaining dust with a dry cloth. if any

resin has built up on the sanding drum, remove

the sandpaper strip and use a resin dissolving

cleaner to remove the resin. Clean the conveyor

belt with soapy water.

figure 29. location of lubrication points.

cleaning Sandpaper

When the sandpaper strip becomes loaded with

built-up sawdust and gum, run a sandpaper

cleaner pad through the machine several times

along the full length of the sanding drum until the

sandpaper is clean (see page 28 for an option

from grizzly).

-29-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

SEctiON 7: SERvicE

review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-

ops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical

support at (570) 546-9663.

troubleshooting

symptom

possible Cause

possible solution

Machine does

not start or a

breaker trips.

1. switch disabling key removed.

1. re-install switch disabling key.

2. Ensure power source is ON and has correct

voltage.

2. power source switched OFF or at fault.

3. plug/receptacle at fault; wired incorrectly.

4. start capacitor at fault.

3. test for good contacts; correct the wiring.

4. test; replace if faulty.

5. Motor connection wired incorrectly.

6. Motor overloaded and its circuit

breaker tripped.

5. Correct motor wiring (see page 40).

6. Wait for motor to cool, then reduce depth of cut

or feed rate.

7. power source circuit breaker tripped.

7. Ensure circuit size is correct (see page 9);

replace weak circuit breaker; reduce depth of

cut or feed rate.

8. Wiring open; has high resistance.

9. oN/oFF switch at fault.

10. Motor at fault.

8. Check and repair open or corroded wiring.

9. replace switch.

10 test; replace if faulty.

Machine stalls

or is overloaded.

1. Workpiece material not suitable for

machine.

1. only sand natural wood products; ensure

moisture content is below 20%.

2. depth of cut too much; feed rate too much. 2. reduce depth of cut; reduce feed rate.

3. dust collection ducting problem.

3. Clear blockages, seal leaks, use smooth wall

duct, eliminate bends, close other branches.

4. Correct motor wiring (see page 40).

4. Motor connection wired incorrectly.

5. power source not adequate.

5. Ensure circuit size is correct (see page 9).

Machine has

excessive

vibration or

1. sandpaper torn or not properly installed.

2. Motor or component loose.

1. replace/re-install sandpaper (see page 21).

2. inspect/replace damaged fasteners, and

re-tighten with thread locking fluid.

3. Move machine or shim under legs until it sits

evenly.

noisy operation.

3. Machine sits unevenly on floor.

4. Motor fan rubbing on fan cover.

5. Motor bearings at fault.

4. Fix/replace fan cover or fan.

5. test by rotating shaft by hand; rotational

grinding or loose shaft requires bearing

replacement.

6. sanding drum bearings at fault.

6. replace bearings.

grit rubs off

sandpaper easily.

1. sandpaper has been stored in an

incorrect environment.

1. store sandpaper away from extreme dry/moist

environment or hot temperatures.

2. sandpaper has been folded or damaged.

2. store sandpaper rolled, not folded or bent.

-30-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

symptom

possible Cause

possible solution

sandpaper

clogs quickly.

1. sanding depth of cut too much or feed

rate too slow.

1. reduce depth of cut or increase feed rate; use

coarser grit sandpaper.

2. Workpiece has high moisture content

or sap.

2. use different stock, or accept the characteristics

of the stock and plan on cleaning/replacing

sandpaper frequently; remove applied finishes

before sanding.

3. Not using the correct grit sandpaper.

4. poor dust collection.

3. use the correct grit sandpaper for the operation

(see page 21).

4. unclog ducts; close gates to improve suction;

re-design dust collection system.

5. sandpaper loaded with sawdust and gum. 5. Clean/replace sandpaper (see page 29).

Burn marks on

workpiece.

1. using too fine of sanding grit for depth

of cut.

1. use coarser grit sandpaper or decrease depth

of cut.

2. sandpaper loaded with sawdust and gum. 2. Clean/replace sandpaper (see page 29).

3. Feed rate too slow.

3. increase feed rate.

4. sanding strip overlapped.

4. properly re-install sandpaper strip (see page 21).

glazed

1. sanding wet stock.

1. only sand stock that has moisture content

below 20%.

workpiece

surface after

sanding.

2. sanding stock with high amount of

applied finishes.

2. use different stock, or accept the characteristics

of the stock and plan on cleaning/replacing

sandpaper frequently; remove applied finishes

before sanding.

Workpiece

slips on conveyor.

1. Conveyor belt dirty or worn.

1. Clean/replace conveyor belt (see page 29).

2. properly adjust pressure roller height (see

page 36).

2. pressure rollers not properly adjusted.

uneven

1. Elevation lock knob not tight and

sanding drum is deflecting up.

1. Fully tighten elevation lock knob after setting

the elevation.

workpiece

thickness from

side to side.

2. Conveyor belt not parallel to sanding drum. 2. properly align conveyor belt to sanding drum

(see page 35).

3. gibs are too loose.

3. properly adjust the gibs (see page 34).

4. replace conveyor belt (see page 38).

4. Conveyor belt is worn.

Conveyor belt

slips or does

not track correctly.

1. Belt tension not properly adjusted.

2. Belt tracking not properly adjusted.

3. Conveyor belt is worn.

1. properly adjust belt tension (see page 33).

2. properly adjust belt tracking (see page 33).

3. replace conveyor belt (see page 38).

Elevation

handwheel

hard to rotate.

1. Elevation lock knob tight.

1. loosen the elevation lock knob.

2. Clean and lubricate the leadscrew and nut (see

page 29).

2. leadscrew and nut clogged with sawdust.

3. gibs are too tight.

3. properly adjust the gibs (see page 34).

sandpaper

strip comes off

drum or is loose.

1. sandpaper strip not properly wrapped

onto drum.

1. properly re-install sandpaper strip (see page 21).

2. sandpaper strip not cut to the correct

dimensions.

2. only use sandpaper strips that are cut to the

correct dimensions (see page 21).

3. slack in sanding strip.

3. properly wrap sandpaper strip and make sure

the right end is fully inserted into the drum slot

(see page 21).

4. torn or damaged sandpaper strip.

4. replace sandpaper (see page 21).

-31-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

symptom

possible Cause

possible solution

ripples or

lines in workpiece.

1. uneven feed rate.

1. Maintain an even feed rate through the entire

sanding operation.

2. sanding drum deflecting from workpiece.

2. Make sure the elevation lock knob is tight.

snipe marks

in workpiece.

1. improper pressure roller tension.

2. Workpiece too long to be supported

without additional help.

1. Evenly adjust pressure roller tension (see

page 36).

2. use roller stands or tables on the infeed and

outfeed ends of the conveyor to keep the

workpiece from bending.

-32-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. as a starting point, make sure that the ends

of both tensioning screws extend evenly

conveyor belt

tension & tracking

approximately ⁄4" beyond the hex nut, as

shown in figure 31.

—if the belt slips during operation, rotate the

screws clockwise in small amounts until

the belt no longer slips on the rollers.

the conveyor belt tension and tracking must be

properly adjusted to ensure that the workpiece

correctly and safely passes underneath the sand-

ing drum and that the conveyor belt does not

become damaged during operation.

screw Extends

approximately ⁄4

if the conveyor belt slips on the rollers then the

belt tension needs to be increased.

if the conveyor belt moves to one side or the other

when it is running, then the belt tracking needs to

be adjusted.

tools Needed

Qty

phillips screwdriver #2 ...................................... 1

open-End Wrench 10mm.................................. 1

belt tension

1. disCoNNECt saNdEr FroM poWEr!

figure 317. tensioning screw extending

approximately ⁄4" beyond hex nut.

2. Make sure the conveyor belt is centered on

the rollers.

belt tracking

1. run the conveyor belt at high speed and note

if it tracks to one side or the other—this make

take a couple of minutes to show up.

—if it is not, release the belt tension equally

on both sides of the belt. this is done by

holding the hex nut still (see figure 30)

while rotating the phillips head screw coun-

terclockwise until you can move the belt

from side-to-side with your hand. then,

center the belt on the rollers.

Note: To avoid damaging the belt, do not

allow the belt to track off the rollers.

—if the conveyor belt does not track to one

side or the other, no further adjustments

are necessary.

Note: In the next step, you may have to wait

for several minutes to notice a change in

tracking.

2. rotate the tensioner screw clockwise on the

side the belt is tracking toward until the belt

moves to the center of the rollers, then back

off the screw until it stops tracking to the

opposite side.

tensioners

3. allow the belt to run for several minutes to

make sure it is tracking properly. if neces-

sary, repeat this procedure until the belt is

properly tracking.

hex Nut

figure 30. Conveyor belt tensioners.

screw

-33-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

if the gibs are too loose, the sanding drum will

deflect up during operation, which will result in

poor sanding results.

Gib Adjustment

the gibs apply pressure to the slides of the sand-

ing head (see figures 32–33). this allows the

sanding head assembly to accurately move up

and down when using the elevation handwheel.

if the gibs are too tight, it will be difficult to adjust

the sanding drum elevation, which will cause

excessive wear on the parts of the elevation sys-

tem.

to adjust the gibs:

1. disCoNNECt saNdEr FroM poWEr!

2. loosen the center lock nut on both gibs (see

figure 32).

slide

3. adjust each of the six gib cap screws in or

out in small, equal amounts, then rotate the

elevation handwheel to test the sanding head

movement.

lock

Nut

Note: Tighten the cap screws to increase gib

pressure.

figure 32. location of rear slide and lock nut.

4. repeat Step 3 until you are satisfied with the

sanding head movement, then re-tighten both

lock nuts.

gib

Cap

(1 of 2)

screws

figure 33. location of rear gib and cap screws.

-34-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. take several light cuts through the sander

without rotating or flipping the board.

conveyor belt to

Drum Alignment

4. Make measurements at "a" and "B" as indi-

cated in figure 34.

to ensure good sanding results, the conveyor belt

and sanding drum must be parallel with each other

from side to side (see the illustration in figure 34).

otherwise, more material will be removed from

one side of the workpiece than the other.

—if measurement "a" is less than "B", loosen

or remove the cap screws on the right con-

veyor support (see figure 35) and shim

between the support and frame to com-

pensate for the difference between "a" and

"B".

CORRECT

Sanding Drum

Conveyor Belt

(Within 0.05" side-to-side)

(Front View)

right

left

support

INCORRECT

figure 35. Conveyor supports.

Conveyor Belt

—if measurement "B" is less than "a", loosen

or remove the cap screws on the left

conveyor support and shim between the

support and frame to compensate for the

difference.

figure 34. illustration of conveyor belt to

sanding drum parallelism.

5. repeat Steps 2–4 to verify the adjustment.

if necessary, repeat this procedure until the

conveyor belt and sanding drum parallelism

is within 0.05" difference from side to side.

the goal of this procedure is to bring the conveyor

belt and sanding drum parallelism within 0.05" dif-

ference from side to side.

items Needed

Qty

Board 2" thick x 8–10" Wide ............................ 1

hex Wrench 6mm.............................................. 1

Metal shim Material........................... as Needed

to check and adjust the conveyor belt to sand-

ing drum parallelism:

1. Make sure the gibs are properly adjusted.

2. plane the board so that the thickness on each

side of it is equal.

-35-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

proper pressure on the workpiece helps avoid

kickback and keeps the workpiece from slipping.

however, as pressure increases on the workpiece

from the rear pressure roller, snipe also increases.

in this case, decrease the pressure on the rear

roller.

pressure Roller

Adjustment

the height of the pressure rollers (see figure 36)

is set slightly below the bottom of the sanding

drum to keep the workpiece firmly against the

conveyor belt as it passes through the sander,

preventing workpiece kickback.

if you choose to increase or decrease the pres-

sure that these rollers exert on the workpiece,

perform the following procedure.

tool Needed

Qty

hex Wrench 5mm.............................................. 1

phillips screwdriver #2 ...................................... 1

to adjust the pressure rollers:

1. disCoNNECt saNdEr FroM poWEr!

2. remove the cap screw that secures the dust

collection hood, then lift the hood up to gain

access to the pressure roller adjustment

screws.

pressure

rollers

3. to increase the pressure exerted by the roll-

ers, tighten all four screws in small, equal

amounts, then test the pressure of the rollers

by pressing up on them.

figure 36. location of the pressure rollers.

the pressure these rollers exert on the workpiece

as it passes underneath the sanding head is con-

trolled by compression springs and adjustment

screws (see figure 37).

Conversely, loosen the adjustment screws to

lessen the pressure.

4. test your adjustments by sanding a scrap

workpiece.

—if the workpiece tends to kickback, reduce

the pressure by rotating the screws coun-

terclockwise one turn, then perform the test

again.

—if the workpiece slips on the conveyor

belt, increase the pressure by rotating the

screws clockwise one turn, then perform

the test again.

pressure adjustment

screws (one side shown)

figure 37. location of the pressure roller

adjustment screws.

-36-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

to adjust the elevation stop screw:

Adjusting Elevation

Stop

1. Make sure the conveyor belt is properly

tensioned (refer to conveyor belt tension

& tracking on page 33 for detailed instruc-

tions).

a phillips head screw that protrudes through the

bottom of the frame acts as a stop to prevent

the sanding drum from making contact with the

conveyor belt when adjusting the height (see

figure 38).

2. disCoNNECt saNdEr FroM poWEr!

3. raise the sanding drum all the way up.

4. loosen the hex nut on the stop screw, then

adjust the height of the screw that protrudes

above the frame to be no less than ¹⁄4".

5. re-tighten the hex nut, then lower the sand-

ing drum until the stop screw contacts the

motor mount frame.

6. Verify that the sanding drum is at least ⁄16"

above the surface of the conveyor belt.

screw &

hex Nut

—if the sanding drum is not at least ⁄16"

above the conveyor belt, repeat this proce-

dure until it is.

figure 38. location of the elevation stop.

the setting of the elevation stop screw was cor-

rectly set at the factory. however, if it is necessary

to re-adjust the stop screw, perform this proce-

dure.

tools Needed

Qty

Wrench 10mm ................................................... 1

phillips screwdriver #2 ...................................... 1

-37-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

4. remove the two cap screws and flat washers

from the conveyor support (see figure 39).

conveyor belt

Replacement

5. lifttheconveyorsupportupslightlyandslipthe

conveyor belt off, as shown in figure 40.

if the conveyor belt becomes excessively worn

or damaged, it can easily be replaced. Contact

grizzly Customer support at 1-800-523-4777 to

obtain a replacement belt (part No. p0706101).

items Needed

Qty

phillips screwdriver #2 ...................................... 1

open-End Wrench 10mm.................................. 1

Wrench or socket 13mm................................... 1

hex Wrench 6mm.............................................. 1

replacement Conveyor Belt.............................. 1

to replace the conveyor belt:

1. disCoNNECt saNdEr FroM poWEr!

figure 40. removing the conveyor belt.

2. Fully release the belt tension (see conveyor

belt tension & tracking on page 33 for

detailed instructions).

6. after sliding the replacement belt on, replace

the conveyor support cap screws and flat

washers, then re-install the sanding head

support with the fasteners you removed in

Step 3.

Note: In the next step, take care to keep the

spacers and washers on the hex bolts in the

same configuration for re-installation.

7. properly tension the conveyor belt before con-

necting the sander to power (see conveyor

belt tension & tracking on page 33 for

detailed instructions).

3. remove the knob and flat washer from the top

of the sanding head support (see figure 39),

remove the hex bolts, spacers, and washers

from the bottom of the support, then remove

the support.

sanding

head support

Conveyor

support

figure 39. location of sanding head and

conveyor supports.

-38-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

SEctiON 8: WiRiNG

these pages are current at the time of printing. however, in the spirit of improvement, we may make chang-

es to the electrical systems of future machines. study this section carefully. if there are differences between

your machine and what is shown in this section, call technical support at (570) 546-9663 for assistance

BEForE making any changes to the wiring on your machine.

Wiring Safety instructions

SHOCK HAZARD. Working on wiring that is con- WIRE/COMPONENT DAMAGE. Damaged wires

nected to a power source is extremely dangerous. or components increase the risk of serious per-

Touching electrified parts will result in personal sonal injury, fire, or machine damage. If you notice

injury including but not limited to severe burns, that any wires or components are damaged while

electrocution, or death. Disconnect the power performing a wiring task, replace those wires or

from the machine before servicing electrical com- components.

ponents!

MOTOR WIRING. The motor wiring shown in

MODIFICATIONS. Modifying the wiring beyond these diagrams is current at the time of printing

what is shown in the diagram may lead to unpre- but may not match your machine. If you find this

dictable results, including serious injury or fire. to be the case, use the wiring diagram inside the

This includes the installation of unapproved after- motor junction box.

market parts.

CAPACITORS/INVERTERS. Some capacitors

WIRE CONNECTIONS. All connections must and power inverters store an electrical charge for

be tight to prevent wires from loosening during up to 10 minutes after being disconnected from

machine operation. Double-check all wires dis- the power source. To reduce the risk of being

connected or connected during any wiring task to shocked, wait at least this long before working on

ensure tight connections.

capacitors.

CIRCUIT REQUIREMENTS. You MUST follow EXPERIENCING DIFFICULTIES. If you are expe-

the requirements at the beginning of this man- riencing difficulties understanding the information

ual when connecting your machine to a power included in this section, contact our Technical

source.

Support at (570) 546-9663.

The photos and diagrams

included in this section are

best viewed in color. You

can view these pages in

color at www.grizzly.com.

-39-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

G0716 Wiring Diagram

Sanding Motor

Thermal

Overload

Circuit

Ground

Breaker

figure 41. sanding motor wiring.

Start Capacitor

80Mfd 300VAC

figure 42. switch wiring.

Ground

ON/OFF

Switch

Bridge

Rectifier

Conveyor

Motor

Hot

Neutral

Conveyor

Transformer

Omron

DB-B838

120V/60Hz

24V/1.4A

Circuit

Board

HF-7A

5-15 Plug 110VAC

(As Recommended)

READ ELECTRICAL SAFETY

ON PAGE 39!

-40-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

SEctiON 9: pARtS

Stand

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

P0716001

HANDLE GRIP

HANDLE

P0716016

RIGHT LONG TOP BRACE

LOCK NUT M8-1.25

P0716002

PS25M

PLN04M

P0716018

PCB11M

P0716020

P0716021

PB03M

PHLP HD SCR M4-.7 X 35

HANDLE BRACKET

LEFT REAR STAND LEG

P0716004

P0716005

PFH43M

PN04M

CARRIAGE BOLT M8-1.25 X 12

HANDLE BASE

LEFT WHEEL MOUNTING BRACKET

WHEEL 5"

FLAT HD SCR M6-1 X 10

HEX NUT M4-.7

HEX BOLT M8-1.25 X 16

WHEEL AXLE

P0716008

P0716009

P0716010

PLN03M

LEFT FRONT STAND LEG

LEG FOOT PAD

P0716023

P0716024

P0716025

P0716026

PW04M

RIGHT REAR STAND LEG

RIGHT WHEEL MOUNTING BRACKET

COTTER PIN 4 X 20

RIGHT FRONT STAND LEG

LOCK NUT M6-1

P0716012

P0716013

P0716014

P0716015

SHORT BOTTOM BRACE

FRONT SHORT TOP BRACE

LEFT LONG TOP BRACE

LONG BOTTOM BRACE

FLAT WASHER 10MM

LOCK NUT M10-1.5

PLN05M

P0716029

REAR SHORT TOP BRACE

-41-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

conveyor

-42-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

conveyor parts List

REF PART #

P0716101

PCAP24M CAP SCREW M5-.8 X 16

DESCRIPTION

CONVEYOR BELT

REF PART #

DESCRIPTION

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

124

125

126

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

PS02M

PHLP HD SCR M4-.7 X 12

SWITCH HOUSING BRACKET

TERMINAL BLOCK 4P

P0716131

P0716132

P0716133

P0716134

PS38M

P0716103

P0716104

PN01M

COMPRESSION SPRING

INFEED ROLLER BRACKET

HEX NUT M6-1

SWITCH HOUSING PLATE

TRANSFORMER OMRON HF-7A 24/120V

PHLP HD SCR M4-.7 X 10

HEX BOLT M8-1.25 X 16

INSULATION PLATE

P0716106

PS115M

P0716108

P0716109

PW02M

ADJUSTABE SLIDE

PHLP HD SCR M6-1 X 90

FEED ROLLER BUSHING

OUTFEED ROLLER

FLAT WASHER 5MM

LOCK WASHER 5MM

HEX NUT M5-.8

PB03M

P0716137

P0716138

P0716139

P0716140

P0716141

P0716142

PB08M

STRAIN RELIEF 1/2" SNAP-IN

POWER CORD 14G 3C 10' 5-15

CONVEYOR MOTOR 24VDC

SWITCH HOUSING

PLW01M

PN06M

PW01M

FLAT WASHER 8MM

INSULATION PAD

PCAP58M CAP SCREW M8-1.25 X 12

HEX BOLT M6-1 X 20

P0716115

PCB22M

PW03M

ADJUSTABLE SLIDE BRACKET

CARRIAGE BOLT M6-1 X 16

FLAT WASHER 6MM

P0716144

PW05M

CONVEYOR CLUTCH

FLAT WASHER 4MM

PW02M

FLAT WASHER 5MM

PLW03M

P0716119

PS06M

LOCK WASHER 6MM

P0716147

PS19M

VS FEED DIAL HF-7A 071015

PHLP HD SCR M5-.8 X 6

HEX NUT M4-.7

INFEED ROLLER

PHLP HD SCR M5-.8 X 20

SWITCH COVER

PN04M

P0716124

G8988

PS09M

PHLP HD SCR M5-.8 X 10

CONVEYOR PLATEN

GRIZZLY SAFETY ON/OFF SWITCH

P0716151

-43-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Main

-44-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Main parts List

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

201

202

203

204

205

206

207

208

209

210

211

212

P0716201

PB26M

CLUTCH DAMPER

250

251

252

253

254

255

256

257

258

259

260

261

262

263

264

265

266

267

268

269

270

271

272

273

274

275

276

277

278

279

280

281

PW06M

FLAT WASHER 12MM

ELEVATION ROTATION LABEL

HANDWHEEL ASSEMBLY

ELEVATION LEADSCREW

KEY 5 X 5 X 16

HEX BOLT M8-1.25 X 30

DUST HOOD

P0716251

P0716252

P0716253

PK08M

P0716203

P0716204

PLN04M

P0716206

P0716207

PCAP31M

PFH31M

P0716210

PLW02M

PN04M

DUST CONNECTOR 90 DEG 4"

LOCK NUT M8-1.25

LOCKING PLATE

PB148M

HEX BOLT M5-.8 X 16

SHAFT END CAP

DUST HOOD HANDLE

CAP SCREW M8-1.25 X 25

FLAT HD SCR M4-.7 X 8

LEFT SANDPAPER CLAMP

LOCK WASHER 4MM

HEX NUT M4-.7

P0716256

P0716257

P0716258

P0716259

P0716260

P0716261

PS31M

STEEL BALL

BEARING RACE

FRAME CASTING

LEADSCREW FLAT WASHER 16MM

THIN NUT M16-1.5

213V2 P0716213V2 SANDING DRUM V2.08.10

PHLP HD SCR M6-1 X 35

HEX BOLT M8-1.25 X 40

ROLL PIN 6 X 26

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

P0716214

P0716215

PR19M

SANDPAPER 3"W X 63" 80GRIT

TORSION SPRING

PB126M

PRP109M

P0716265

P0716266

P0716267

PLW04M

PB07M

EXT RETAINING RING 28MM

RIGHT SANDPAPER CLAMP

INTERNAL DRUM GUARD

FLAT HD SCR M6-1 X 30

DUST HOOD HINGE

ELEVATION SCALE

P0716217

P0716218

PFH26M

P0716220

PCB34M

P0716222

P6205-2RS

P0716224

P0716225

PW01M

OUTFEED ROLLER SUPPORT

INFEED ROLLER SUPPORT

LOCK WASHER 8MM

HEX BOLT M8-1.25 X 25

CONVEYOR SUPPORT

THREADED STUD M8-1.25 X 80

DRUM HOUSING SUPPORT

FENDER WASHER 8MM

KNOB M8-1.25

CARRIAGE BOLT M8-1.25 X 25

OUTSIDE BEARING RETAINER

BALL BEARING 6205-2RS

INTERNAL BEARING RETAINER

DRUM HOUSING

P0716270

P0716271

P0716272

PWF08M

P0716274

PB01M

FLAT WASHER 8MM

HEX BOLT M10-1.5 X 30

LOCK WASHER 10MM

FLAT WASHER 10MM

MOTOR MOUNT

PN03M

HEX NUT M8-1.25

PLW06M

PW04M

PN01M

HEX NUT M6-1

P0716229

PCAP27M

PW03M

POINTER

P0716278

P0716279

PCAP13M

P0716281

CAP SCREW M6-1 X 14

FLAT WASHER 6MM

GIB

CAP SCREW M8-1.25 X 30

MOTOR 1-1/2HP 110V 60HZ

P0716233

PS40M

AUXILIARY GUARD

PHLP HD SCR M5-.8 X 16

DRUM CLUTCH

281-1 P0716281-1 MOTOR FAN COVER

281-2 P0716281-2 MOTOR FAN

P0716235

PSS03M

PCAP39M

PW05M

SET SCREW M6-1 X 8

CAP SCREW M4-.7 X 20

FLAT WASHER 4MM

281-3 P0716281-3 MOTOR JUNCTION BOX

281-4 P0716281-4 S CAPACITOR 80M 300V 2 X 3-5/8

281-5 P0716281-5 MOTOR CORD 14G 3C 18"

281-6 P0716281-6 CIRCUIT BREAKER CRU 12A

PW02M

FLAT WASHER 5MM

PLW01M

PS51M

LOCK WASHER 5MM

282

283

284

285

286

287

288

289

290

PCAP45M

PAW06M

PAW05M

PWR1113

PW01M

CAP SCREW M8-1.25 X 45

HEX WRENCH 6MM

HEX WRENCH 5MM

COMBO WRENCH 11/13

FLAT WASHER 8MM

SPACER 8MM

PHLP HD SCR M4-.7 X 30

COMPRESSION SPRING

PRESSURE ROLLER BRACKET

RIGHT BRACKET SUPPORT

LEFT BRACKET SUPPORT

LOCK NUT M4-.7

P0716242

P0716243

P0716244

P0716245

PLN01M

P0716247

P0716248

PN26M

P0716287

PN06M

HEX NUT M5-.8

PRESSURE ROLLER BUSHING

PRESSURE ROLLER

PB14M

HEX BOLT M10-1.5 X 35

HOLDING PIN

P0716290

ACORN NUT M12-1.75

-45-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

Machine Labels

302

301

303

304

307

305

306

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

301

302

303

304

P0716301

DISCONNECT/DUST HAZARD LABEL

ELECTRICITY LABEL

305

306

307

P0716305

P0716306

P0716307

MACHINE ID LABEL

PLABEL-14

PLABEL-55

PLABEL-12A

MODEL NUMBER LABEL

WHITE TOUCH-UP PAINT

ENTANGLEMENT HAZARD LABEL

READ MANUAL LABEL

Safety labels warn about machine hazards and ways to prevent injury. the owner of this machine

MUSt maintain the original location and readability of the labels on the machine. if any label is

removed or becomes unreadable, REpLAcE that label before using the machine again. contact

Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-46-

Model g0716 (Mfg. since 2/11)

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY CARD

Name_____________________________________________________________________________

Street_____________________________________________________________________________

City _______________________ State_________________________ Zip _____________________

Phone #____________________ Email ________________________ Invoice #_________________

Model # ____________________ Order #_______________________ Serial #__________________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop

better products and services. Of course, all information is strictly confidential.

1. How did you learn about us?

____ Advertisement

____ Card Deck

____ Friend

____ Website

____ Catalog

____ Other:

2. Which of the following magazines do you subscribe to?

____ Cabinetmaker & FDM

____ Family Handyman

____ Hand Loader

____ Popular Science

____ Popular Woodworking

____ Precision Shooter

____ Projects in Metal

____ RC Modeler

____ Riﬂe

____ Shop Notes

____ Wooden Boat

____ Woodshop News

____ Woodsmith

____ Handy

____ Woodwork

____ Home Shop Machinist

____ Journal of Light Cont.

____ Live Steam

____ Woodworker West

____ Woodworker’s Journal

____ Other:

____ Model Airplane News

____ Old House Journal

____ Popular Mechanics

____ Shotgun News

____ Today’s Homeowner

____ Wood

3. What is your annual household income?

____ $20,000-$29,000

____ $30,000-$39,000

____ $40,000-$49,000

____ $70,000+

____ $50,000-$59,000

____ $60,000-$69,000

4. What is your age group?

____ 20-29

____ 30-39

____ 60-69

____ 40-49

____ 70+

____ 50-59

5. How long have you been a woodworker/metalworker?

____ 0-2 Years ____ 2-8 Years

____ 8-20 Years

____20+ Years

____10+

6. How many of your machines or tools are Grizzly?

____ 0-2 ____ 3-5

____ 6-9

7. Do you think your machine represents a good value?

8. Would you recommend Grizzly Industrial to a friend?

_____Yes

_____No

9. Would you allow us to use your name as a reference for Grizzly customers in your area?

Note: We never use names more than 3 times. _____Yes _____No

10. Comments:_____________________________________________________________________

_________________________________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

FOLD ALONG DOTTED LINE

Place

Stamp

Here

GRIZZLY INDUSTRIAL, INC.

P.O. BOX 2069

BELLINGHAM, WA 98227-2069

FOLD ALONG DOTTED LINE

Send a Grizzly Catalog to a friend:

Name_______________________________

Street_______________________________

City______________State______Zip______

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANty AND REtURNS

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from

the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,

negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty

and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-

ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent

that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and

any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,

or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then

issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the

carton. We will not accept any item back without this number. Proof of purchase must accompany the

merchandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to

achieve better quality equipment. We make every effort to ensure that our products meet high quality and

durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

Download from Www.Somanuals.com. All Manuals Search And Download.

Buy Direct and Save with Grizzly^®– Trusted, Proven and a Great Value!

~Since 1983~

Visit Our Website Today For

Current Specials!

ORDER

24 HOURS A DAY!

1-800-523-4777

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Stroller PD223368A User Manual
Grindmaster Ice Tea Maker TEA 300 User Manual
Grizzly Saw G1023 User Manual
Haan Carpet Cleaner SS 25 User Manual
Haier Washer HWM 80 000 S User Manual
Hearth and Home Technologies Outdoor Fireplace Grand XT User Manual
Heath Zenith Door 3106978 AC 6196 User Manual
Honeywell Thermostat TL5110 User Manual
HP Hewlett Packard Clock Radio 5345A User Manual
Husqvarna Blower 953210103 User Manual