Instructions – Parts List
POLYPROPYLENE AND PVDF
Huskyt 2150 Air-Operated
Diaphragm Pumps
308550ZAC
EN
2–inch AODD pump for fluid transfer applications. For professional
use only.
Not approved to European explosive atmosphere requirements.
See Models on page 2 for a list of pump models and descriptions.
120 psi (0.8 MPa, 8 bar) Maximum Fluid Working Pressure
120 psi (0.8 MPa, 8 bar) Maximum Air Input Pressure
Patent No.
CN ZL94102643.4
FR 9408894
JA 351720
US 5,368,452
Important Safety Instructions
Read all warnings and instructions in the
manual. Save these instructions.
See page 2 for table of contents.
04613B
Download from Www.Somanuals.com. All Manuals Search And Download.
Symbols
Warning Symbol
Caution Symbol
WARNING
CAUTION
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
D This equipment is for professional use only.
INSTRUCTIONS
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.
D Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure of the lowest rated component in your system.
This equipment has a 120 psi (0.8 MPa, 8 bar) maximum working pressure at 120 psi
(0.8 MPa, 8 bar) maximum incoming air pressure.
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the
Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s
warnings.
D Do not use hoses to pull equipment.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not ex-
pose Graco hoses to temperatures above 82_C (180_F) or below –40_C (–40_F).
D Do not lift pressurized equipment.
D Wear hearing protection when operating this equipment.
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
308550
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the
skin, inhaled, or swallowed.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid
and solvent manufacturer.
D Pipe and dispose of the exhaust air safely, away from people, animals, and food handling areas.
If the diaphragm fails, the fluid is exhausted along with the air. See Air Exhaust Ventilation on
page 11.
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D Ground the equipment. Refer to Grounding on page 6.
D Never use a polypropylene or PVDF pump with non-conductive flammable fluids as specified by
your local fire protection code. Refer to Grounding on page 6 for additional information. Consult
your fluid supplier to determine the conductivity or resistivity of your fluid.
D If there is any static sparking or you feel an electric shock while using this equipment, stop
pumping immediately. Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed, dispensed, or transferred.
D Pipe and dispose of the exhaust air safely, away from all sources of ignition. If the diaphragm
fails, the fluid is exhausted along with the air. See Air Exhaust Ventilation on page 11.
D Keep the work area free of debris, including solvent, rags, and gasoline.
D Electrically disconnect all equipment in the work area.
D Extinguish all open flames or pilot lights in the work area.
D Do not smoke in the work area.
D Do not turn on or off any light switch in the work area while operating or if fumes are present.
D Do not operate a gasoline engine in the work area.
4
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
General Information
Tighten Screws Before First Use
D The Typical Installation shown in Fig. 2 is only a
guide for selecting and installing system compo-
nents. Contact your Graco distributor or Graco
Technical Assistance (see back page) for assis-
tance in planning a system to suit your needs.
Before using the pump for the first time, check and
retorque all external fasteners. See Torque Se-
quence, page 32. After the first day of operation,
retorque the fasteners. Although pump use varies, a
general guideline is to retorque fasteners every two
months.
D Always use Genuine Graco Parts and Accessories.
Be sure all accessories are adequately sized and
pressure-rated to meet the system’s requirements.
D Reference numbers and letters in parentheses refer
to the callouts in the figures and the parts lists on
pages 28–31.
D Variations in color between the plastic components
of this pump are normal. Color variation does not
affect the performance of the pump.
WARNING
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can
cause serious injury or death if splashed
in the eyes or on the skin, inhaled, or
swallowed.
1. Read TOXIC FLUID HAZARD on page 4.
2. Use fluids and solvents which are compatible
with the equipment wetted parts. Refer to the
Technical Data section of all equipment manu-
als. Read the fluid and solvent manufacturer’s
warnings.
308550
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Ground all of this equipment:
Grounding
D Air Motor: Connect a ground wire and clamp as
shown in Fig. 1. Loosen the grounding screw (W).
Insert one end of a 12 ga (1.5 mm@) minimum
ground wire (Y) behind the grounding screw and
tighten the screw securely. Connect the clamp end
of the ground wire to a true earth ground. Order
Part No. 237569 Ground Wire and Clamp.
WARNING
FIRE AND EXPLOSION HAZARD
This pump must be grounded. Before
operating the pump, ground the system
as explained below. Also, read the sec-
tion FIRE AND EXPLOSION HAZARD,
on page 4.
NOTE: When pumping conductive flammable fluids
with a polypropylene or a PVDF pump, always ground
the entire fluid system. See the WARNING on page
6.
D Air and fluid hoses: Use only electrically conductive
Polypropylene and PVDF are not conductive.
Attaching the ground wire to the grounding lug will
ground only the air motor. When pumping conduc-
tive flammable fluids, always ground the entire
fluid system by making sure the fluid has an electri-
cal path to a true earth ground. See Fig. 1.
hoses.
D Air compressor: Follow the manufacturer’s recom-
mendations.
D All solvent pails used when flushing: Follow the
local code. Use only metal pails, which are conduc-
tive. Do not place the pail on a non-conductive
surface, such as paper or cardboard, which inter-
rupts the grounding continuity.
Never use a polypropylene or a PVDF pump with
non-conductive flammable fluids as specified by
your local fire protection code.
US Code (NFPA 77 Static Electricity) recommends
D Fluid supply container: Follow the local code.
–12
a conductivity greater than 50 x 10
Siemans/me-
ter (mhos/meter) over your operating temperature
range to reduce the hazard of fire. Consult your
fluid supplier to determine the conductivity or
resistivity of your fluid. The resistivity must be less
12
than 2 x 10 ohm-centimeters.
Y
To reduce the risk of static sparking, ground the pump
and all other equipment used or located in the pumping
area. Check your local electrical code for detailed
grounding instructions for your area and type of equip-
ment.
W
02646B
Fig. 1
6
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
b. Locate one bleed-type master air valve (B)
Air Line
close to the pump and use it to relieve trapped
air. See the WARNING at left. Locate the other
master air valve (E) upstream from all air line
accessories and use it to isolate them during
cleaning and repair.
WARNING
A bleed-type master air valve (B) is required in
your system to relieve air trapped between this
valve and the pump. Trapped air can cause the
pump to cycle unexpectedly, which could result in
serious injury, including splashing in the eyes or on
the skin, injury from moving parts, or contamination
from hazardous fluids. See Fig. 2.
c. The air line filter (F) removes harmful dirt and
moisture from the compressed air supply.
2. Install an electrically conductive, flexible air hose
(A) between the accessories and the 1/2 npt(f)
pump air inlet (N). See Fig. 2. Use a minimum 1/2”
(13 mm) ID air hose.
1. Install the air line accessories as shown in Fig. 2.
Mount these accessories on the wall or on a
bracket. Be sure the air line supplying the acces-
sories is electrically conductive.
3. Screw an air line quick disconnect coupler (D) onto
the end of the air hose (A); be sure the coupler
porting is large enough to not restrict the air flow,
which will affect pump performance. Screw the
mating fitting into the pump air inlet snugly. Do not
connect the coupler (D) to the fitting until you are
ready to operate the pump.
a. Install an air regulator (C) and gauge to control
the fluid pressure. The fluid outlet pressure will
be the same as the setting of the air regulator.
TYPICAL FLOOR-MOUNT INSTALLATION
B
C
E
F
KEY FOR FIG. 2
A
B
Electrically conductive air supply hose
Bleed-type master air valve
(required for pump)
C
D
E
F
G
H
J
Air regulator
Air line quick disconnect
Master air valve (for accessories)
Air line filter
Fluid suction hose
Fluid supply
Fluid drain valve (required)
Fluid shutoff valve
Fluid hose
A
D
K
S
L
K
l
N
R
S
Y
1/2 npt(f) air inlet port
2” fluid inlet flange
2” fluid outlet flange
Ground wire (required; see page 6
for installation instructions)
N
J
Y
H
R
G
04614B
Fig. 2
308550
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation of Remote Pilot Air Lines
Fluid Suction Line
1. Refer to Parts Drawings. Connect air line to pump
as in preceding steps.
1. The pump fluid inlet (R) is a 2” raised face flange.
Refer to Flange Connections on page 9.
2. Connect 1/4 in. O.D. tubing to push type connec-
tors (14) on air motor of pump.
2. If the fluid inlet pressure to the pump is more than
25% of the outlet working pressure, the ball check
valves will not close fast enough, resulting in
inefficient pump operation.
NOTE: by replacing the push type connectors, other
sizes or types of fittings may be used. The new fittings
will require 1/8 in. npt threads.
3. At inlet fluid pressures greater than 15 psi
(0.1 MPa, 1 bar), diaphragm life will be shortened.
3. Connect remaining ends of tubes to external air
signal, such as Graco’s Cycleflo (P/N 195264) or
Cycleflo II (P/N195265) controllers.
4. See the Technical Data on page 34 for maximum
suction lift (wet and dry).
Mountings
Fluid Outlet Line
CAUTION
The pump exhaust air may contain contaminants.
Ventilate to a remote area if the contaminants
could affect your fluid supply. See Air Exhaust
Ventilation on page 11.
WARNING
A fluid drain valve (J) is required to relieve pres-
sure in the hose if it is plugged. The drain valve
reduces the risk of serious injury, including splash-
ing in the eyes or on the skin, or contamination
from hazardous fluids when relieving pressure.
Install the valve close to the pump fluid outlet. See
Fig. 2.
D Be sure the mounting surface can support the
weight of the pump, hoses, and accessories, as
well as the stress caused during operation.
D For all mountings, be sure the pump is bolted
directly to the mounting surface.
1. The pump fluid outlet (S) is a 2” raised face flange.
Refer to Flange Connections on page 9.
D For ease of operation and service, mount the pump
so the air valve cover (2), air inlet, and fluid inlet
and outlet ports are easily accessible.
2. Install a fluid drain valve (J) near the fluid outlet.
See the WARNING above.
D Rubber Foot Mounting Kit 236452 is available to
reduce noise and vibration during operation.
3. Install a shutoff valve (K) in the fluid outlet line.
8
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
1. Place a flat washer (E) on each bolt (C). Refer to
Flange Connections
Fig. 3.
The fluid inlet and outlet ports are 2” raised face,
standard 150 lb class pipe flanges. Connect 2” flanged
plastic pipe to the pump as follows. You will need:
2. Align the holes in the gasket (B) and the pipe
flange (A) with the holes in the pump outlet
flange (S).
D Torque wrench
D Adjustable wrench
3. Lubricate the threads of the four bolts. Install the
bolts through the holes and secure with the wash-
ers (E), lockwashers (D), and nuts (F).
D 6” diameter, 1/8” thick PTFE gasket, with four 0.75”
diameter holes on a 4.75” diameter bolt circle, and
a 2.20” diameter center
4. Hold the nuts with a wrench. Refer to the tighten-
ing sequence in Fig. 3 and torque the bolts to
20–30 ft-lb (27–41 NSm). Do not over-torque.
D Four 5/8” x 3” bolts
D Four 5/8” spring lockwashers
D Eight 5/8” flat washers
D Four 5/8” nuts.
5. Repeat for the pump inlet flange (R).
BOLT TIGHTENING SEQUENCE
1
3
2
1
4
F
D
E
S
B
04405
A
E
C
1
R
KEY FOR FIG. 3
A
B
C
D
E
F
Flanged plastic pipe
PTFE gasket
Bolt
Lockwasher
Flat washer
Nut
R
S
2” fluid inlet flange
2” fluid outlet flange
Lubricate threads. Torque to 20–30 ft-lb
1
(27–41 NSm). Do not over-torque.
04615B
Fig. 3
308550
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Changing the Orientation of the Fluid Inlet
Fluid Pressure Relief Valve
and Outlet Ports
The pump is shipped with the fluid inlet (R) and outlet
(S) ports facing the same direction. See Fig. 4. To
change the orientation of the inlet and/or outlet port:
CAUTION
Some systems may require installation of a pres-
sure relief valve at the pump outlet to prevent
overpressurization and rupture of the pump or
hose. See Fig. 5.
1. Remove the screws and washers (106, 112, 113
and 114) holding the inlet (102) and/or outlet (103)
manifold to the covers (101).
Thermal expansion of fluid in the outlet line can
cause overpressurization. This can occur when
using long fluid lines exposed to sunlight or ambi-
ent heat, or when pumping from a cool to a warm
area (for example, from an underground tank).
2. Reverse the manifold and reattach. Install the
screws and washers and torque to 150–160 in–lb
(17–18 NSm). See Torque Sequence, page 32.
KEY
N
P
1/2 npt(f) air inlet port
Muffler
Air exhaust port is 3/4
npt(f) .
2” fluid inlet flange
2” fluid outlet flange
101 Fluid covers
102 Fluid inlet manifold
103 Fluid outlet manifold
106 Fluid outlet manifold
screws (top)
Overpressurization can also occur if the Husky
pump is being used to feed fluid to a piston pump,
and the intake valve of the piston pump does not
close, causing fluid to back up in the outlet line.
R
S
112 Fluid inlet manifold
screws (bottom)
113 Fluid outlet manifold
washer
114 Fluid inlet manifold
washer
Torque to 150–160 in–lb
(17–18 NSm). See Torque
Sequence, page 32.
1
KEY
R
S
V
2” fluid inlet flange
2” fluid outlet flange
Pressure relief valve
Part No. 112119 (stainless steel)
106
113
1
103
1
2
Install valve between fluid inlet and outlet ports.
Connect fluid inlet line here.
S
3
Connect fluid outlet line here.
N
3
S
V
1
101
R
2
P
R
102
04616B
04613B
114
112
1
Fig. 5
Fig. 4
10
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The air exhaust port is 3/4 npt(f). Do not restrict the air
Air Exhaust Ventilation
exhaust port. Excessive exhaust restriction can cause
erratic pump operation.
WARNING
If the muffler (P) is installed directly to the air exhaust
port, apply PTFE thread tape or anti–seize thread
lubricant to the muffler threads before assembly.
FIRE AND EXPLOSION HAZARD
Be sure to read and follow the warnings
and precautions regarding TOXIC
FLUID HAZARD, and FIRE OR EXPLO-
SION HAZARD on page 4, before op-
erating this pump.
To provide a remote exhaust:
1. Remove the muffler (P) from the pump air exhaust
port.
Be sure the system is properly ventilated for your
type of installation. You must vent the exhaust to a
safe place, away from people, animals, food handl-
ing areas, and all sources of ignition when pumping
flammable or hazardous fluids.
2. Install an electrically conductive air exhaust hose
(T) and connect the muffler (P) to the other end of
the hose. The minimum size for the air exhaust
hose is 3/4 in. (19 mm) ID. If a hose longer than 15
ft (4.57 m) is required, use a larger diameter hose.
Avoid sharp bends or kinks in the hose. See Fig. 6.
Diaphragm failure will cause the fluid being
pumped to exhaust with the air. Place an appropri-
ate container at the end of the air exhaust line to
catch the fluid. See Fig. 6.
3. Place a container (U) at the end of the air exhaust
line to catch fluid in case a diaphragm ruptures.
VENTING EXHAUST AIR
KEY
A
B
Air supply line
Bleed-type master air valve
(required for pump)
C
D
E
F
Air regulator
E
F
C
B
Air line quick disconnect
Master air valve (for accessories)
Air line filter
P
T
U
Muffler
Electrically conductive air exhaust hose
Container for remote air exhaust
A
D
T
U
P
04617
Fig. 6
308550
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
1. Be sure the pump is properly grounded. Refer to
Pressure Relief Procedure
Grounding on page 6.
WARNING
2. Check all fittings to be sure they are tight. Be sure
to use a compatible liquid thread sealant on all
male threads. Tighten the fluid inlet and outlet
fittings securely.
PRESSURIZED EQUIPMENT HAZARD
The equipment stays pressurized until pressure is
manually relieved. To reduce the risk of serious
injury from pressurized fluid, accidental spray from
the gun or splashing fluid, follow this procedure
whenever you:
3. Place the suction tube (if used) in the fluid to be
pumped.
D Are instructed to relieve pressure,
D Stop pumping,
D Check, clean or service any system equipment,
D Install or clean fluid nozzles.
NOTE: If the fluid inlet pressure to the pump is more
than 25% of the outlet working pressure, the ball check
valves will not close fast enough, resulting in inefficient
pump operation.
1. Shut off the air to the pump.
2. Open the dispensing valve, if used.
4. Place the end of the fluid hose (L) into an appropri-
ate container.
3. Open the fluid drain valve to relieve all fluid pres-
sure, having a container ready to catch the drain-
age.
5. Close the fluid drain valve (J). See Fig. 2.
Flush the Pump Before First Use
The pump was tested with lightweight oil, which is left
in the fluid passages to protect parts. To avoid contam-
inating your fluid with oil, flush the pump with a com-
patible solvent before using the equipment. Follow the
steps under Starting and Adjusting the Pump.
6. With the pump air regulator (C) closed, open all
bleed-type master air valves (B, E).
7. If the fluid hose has a dispensing device, hold it
open while continuing with the following step.
Starting and Adjusting the Pump
WARNING
8. Slowly open the air regulator (C) until the pump
starts to cycle. Allow the pump to cycle slowly until
all air is pushed out of the lines and the pump is
primed.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can
cause serious injury or death if splashed
in the eyes or on the skin, inhaled, or
swallowed. Do not lift a pump under pressure. If
dropped, the fluid section may rupture. Always fol-
low the Pressure Relief Procedure above before
lifting the pump.
If you are flushing, run the pump long enough to
thoroughly clean the pump and hoses. Close the
air regulator. Remove the suction tube from the
solvent and place it in the fluid to be pumped.
12
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
NOTE: Leaving air pressure applied to the air motor for
Operation of Remote Piloted Pumps
extended periods when the pump is not running may
shorten the diaphragm life. Using a 3–way solenoid
valve to automatically relieve the pressure on the air
motor when the metering cycle is complete prevents
this from occurring.
1. Fig. 2 and Parts Drawings. Follow preceding steps
1 through 7 of Starting and Adjusting Pump.
2. Open air regulator (C).
Pump Shutdown
WARNING
The pump may cycle once before the external sig-
nal is applied. Injury is possible. If pump cycles,
wait until end before proceeding.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure at left.
3. Pump will operate when air pressure is alternately
applied and relieved to push type connectors (14).
At the end of the work shift, relieve the pressure.
Maintenance
Flush the pump often enough to prevent the fluid you
are pumping from drying or freezing in the pump and
damaging it. Flush with a fluid that is compatible with
the fluid you are pumping and with the wetted parts in
your system. Check with your fluid manufacturer or
supplier for recommended flushing fluids and flushing
frequency.
Lubrication
The air valve is designed to operate unlubricated.
However, if lubrication is desired, every 500 hours of
operation (or monthly) remove the hose from the pump
air inlet and add two drops of machine oil to the air
inlet.
Always flush the pump and relieve the pressure before
storing it for any length of time.
CAUTION
Tightening Threaded Connections
Do not over-lubricate the pump. Oil is exhausted
through the muffler, which could contaminate your
fluid supply or other equipment. Excessive lubrica-
tion can also cause the pump to malfunction.
Before each use, check all hoses for wear or damage,
and replace as necessary. Check to be sure all
threaded connections are tight and leak free. Check
fasteners. Tighten or retorque as necessary. Although
pump use varies, a general guideline is to retorque
fasteners every two months. See Torque Sequence,
page 32.
Flushing and Storage
WARNING
Preventive Maintenance Schedule
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 12.
Establish a preventive maintenance schedule, based
on the pump’s service history. This is especially impor-
tant for prevention of spills or leakage due to dia-
phragm failure.
308550
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
1. Relieve the pressure before checking or servicing
WARNING
the equipment.
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 12.
2. Check all possible problems and causes before
disassembling the pump.
PROBLEM
CAUSE
SOLUTION
Pump cycles at stall or fails to hold
pressure at stall.
Worn check valve balls (301), seats Replace. See page 18.
(201) or o-rings (202).
Pump will not cycle, or cycles once Air valve is stuck or dirty.
and stops.
Disassemble and clean air valve.
See pages 16–17. Use filtered air.
Check valve ball (301) severely
worn and wedged in seat (201) or
manifold (102 or 103).
Replace ball and seat. See page
18.
Check valve ball (301) is wedged
Install Pressure Relief Valve
into seat (201), due to overpressur- (see page 10).
ization.
Dispensing valve clogged.
Clogged suction line.
Sticky or leaking balls (301).
Diaphragm ruptured.
Restricted exhaust.
Suction line is loose.
Diaphragm ruptured.
Relieve pressure and clear valve.
Inspect; clear.
Pump operates erratically.
Air bubbles in fluid.
Clean or replace. See page 18.
Replace. See pages 19–22.
Remove restriction.
Tighten.
Replace. See pages 19–22.
Loose inlet manifold (102), dam-
aged seal between manifold and
Tighten manifold bolts (112) or re-
place seats (201) or o-rings (202).
seat (201), damaged o-rings (202). See page 18.
Loose fluid side diaphragm plate
(105).
Tighten or replace. See pages
19–22.
14
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
PROBLEM
CAUSE
SOLUTION
Fluid in exhaust air.
Diaphragm ruptured.
Replace. See pages 19–22.
Loose fluid side diaphragm plate
(105).
Tighten or replace. See pages
19–22.
Pump exhausts excessive air at
stall.
Worn air valve block (7), o-ring (6), Inspect; replace. See pages 16–17.
plate (8), pilot block (18), u-cups
(10), or pilot pin o-rings (17).
Worn shaft seals (402).
Replace. See pages 19–22.
Pump leaks air externally.
Air valve cover (2) or air valve cover Tighten screws. See page 17.
screws (3) are loose.
Air valve gasket (4) or air cover
gasket (22) is damaged.
Inspect; replace. See pages 16–17,
23–24.
Air cover screws (25) are loose.
Tighten screws. See pages 23–24.
Pump leaks fluid externally from ball Loose manifolds (102, 103), dam-
check valves. aged seal between manifold and
Tighten manifold bolts (106 and
112) or replace seats (201) or
seat (201), damaged o-rings (202). o-rings (202). See page 18.
308550
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Repairing the Air Valve
2
3
2
4{H
Tools Required
D Torque wrench
D Torx (T20) screwdriver or 7 mm (9/32”) socket
D Needle-nose pliers
D O-ring pick
D Lithium base grease
NOTE: Air Valve Repair Kits 236273 (aluminum center
housings) and 255061 (stainless steel center hous-
ings) are available. Refer to page 28. Parts included in
the kit are marked with a symbol, for example (4{H).
Use all the parts in the kit for the best results.
Disassembly
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 12.
Torque to 50–60 in-lb
2
(5.6–6.8 NSm).
04618B
Fig. 7
1. Relieve the pressure.
2. With a Torx (T20) screwdriver or 7 mm (9/32”)
socket wrench, remove the six screws (3), air
valve cover (2), and gasket (4). See Fig. 7.
1
2
5
See Detail at right.
Grease.
2
3
H{6
H{7
3. Move the valve carriage (5) to the center position
and pull it out of the cavity. Remove the valve
block (7) and o-ring (6) from the carriage. Using a
needle-nose pliers, pull the pilot block (18) straight
up and out of the cavity. See Fig. 8.
3
Grease lower face.
4. Pull the two actuator pistons (11) out of the bear-
ings (12). Remove the u-cup packings (10) from
the pistons. Pull the pilot pins (16) out of the
bearings (15). Remove the o-rings (17) from the
pilot pins. See Fig. 9.
3
H{18
5
1
5. Inspect the valve plate (8) in place. If damaged,
use a Torx (T20) screwdriver or 7 mm (9/32”)
socket wrench to remove the three screws (3).
Remove the valve plate (8) and, on aluminum
center housing models only, remove the seal (9).
See Fig. 10.
11
6. Inspect the bearings (12, 15) in place. See Fig. 9.
The bearings are tapered and, if damaged, must
be removed from the outside. This requires disas-
sembly of the fluid section. See page 23.
7. Clean all parts and inspect for wear or damage.
Replace as needed. Reassemble as explained on
page 17.
16
04900
Fig. 8
16
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Install with lips facing
narrow end of piston (11).
Insert wide end first.
1
Rounded side must face down.
1
2
3
4
3
Insert narrow end first.
Grease.
2
Tighten screws until
they bottom out on the
housing.
2
8H
9{
1
10{H
2
3
4
11
12
03947
Fig. 10
1
17{
15 16
2
04901
Fig. 9
Reassembly
1. If you removed the bearings (12, 15), install new
ones as explained on page 23. Reassemble the
fluid section.
6. Lubricate the u-cup packings (10{H) and actuator
pistons (11). Insert the actuator pistons in the
bearings (12), wide end first. Leave the narrow
end of the pistons exposed. See Fig. 9.
2. On aluminum center housing models, install the
valve plate seal (9{) into the groove at the bottom
of the valve cavity. The rounded side of the seal
must face down into the groove. See Fig. 10.
7. Grease the lower face of the pilot block (18{H) and
install so its tabs snap into the grooves on the
ends of the pilot pins (16). See Fig. 8.
8. Grease the o-ring (6{H) and install it in the valve
block (7{H). Push the block onto the valve carriage
(5). Grease the lower face of the valve block. See
Fig. 8.
3. Install the valve plate (8H) in the cavity. On alumi-
num center housing models, the plate is reversible,
so either side can face up. Install the three screws
(3), using a Torx (T20) screwdriver or 7 mm (9/32”)
socket wrench. Tighten until the screws bottom out
on the housing. See Fig. 10.
9. Install the valve carriage (5) so its tabs slip into the
grooves on the narrow end of the actuator pistons
(11). See Fig. 8.
4. Install an o-ring (17{H) on each pilot pin (16).
Grease the pins and o-rings. Insert the pins into
the bearings (15), narrow end first. See Fig. 9.
10. Align the valve gasket (4{H) and cover (2) with the
six holes in the center housing (1). Secure with six
screws (3), using a Torx (T20) screwdriver or 7
mm (9/32”) socket wrench. Torque to 50–60 in-lb
(5.6–6.8 NSm). See Fig. 7.
5. Install a u-cup packing (10{H) on each actuator
piston (11), so the lips of the packings face the
narrow end of the pistons. See Fig. 9.
308550
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Torque to 150–160 in–lb (17–18 NSm). See Torque Se-
quence, page 32.
Ball Check Valve Repair
1
Tools Required
2
Arrow (A) must point toward outlet manifold (103).
D Torque wrench
3
Not used on some models.
106
113
1
D 10 mm socket wrench
D O-ring pick
Disassembly
NOTE: A Fluid Section Repair Kit is available. Refer to
page 27 to order the correct kit for your pump. Parts
included in the kit are marked with an asterisk, for
example (201*). Use all the parts in the kit for the best
results.
103
301*
NOTE: To ensure proper seating of the balls (301),
always replace the seats (201) when replacing the
balls.
201*
202*
101
3
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 12.
A
2
1. Relieve the pressure. Disconnect all hoses.
2. Remove the pump from its mounting.
301*
3. Using a 10 mm socket wrench, remove the eight
bolts (106), and four washers (113), holding the
outlet manifold (103) to the fluid covers (101). See
Fig. 11.
201*
202*
3
4. Remove the seats (201), balls (301), and o-rings
(202) from the manifold.
NOTE: Some models do not use o-rings (202).
102
5. Turn the pump over and remove the bolts (112),
washers (114), and inlet manifold (102). Remove
the seats (201), balls (301), and o-rings (202) from
the fluid covers (101).
114
112
Reassembly
1
1. Clean all parts and inspect for wear or damage.
Replace parts as needed.
04619C
Fig. 11
2. Reassemble in the reverse order, following all
notes in Fig. 11. Be sure the ball checks are as-
sembled exactly as shown. The arrows (A) on the
fluid covers (101) must point toward the outlet
manifold (103).
18
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Diaphragm Repair
WARNING
Tools Required
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 12.
D Torque wrench
D 13 mm socket wrench
D Adjustable wrench
D 19 mm open–end wrench
D O-ring pick
1. Relieve the pressure.
2. Remove the manifolds and disassemble the ball
check valves as explained on page 18.
D Lithium-base grease
Disassembly
NOTE: A Fluid Section Repair Kit is available. Refer to
page 27 to order the correct kit for your pump. Parts
included in the kit are marked with an asterisk, for
example (401*). Use all the parts in the kit for the best
results.
3. Using 13 mm socket wrenches, remove the
screws (107 and 108) holding the fluid covers
(101) to the air covers (23). Pull the fluid covers
(101) off the pump. See Fig. 12.
You must torque the eight long screws (108) first, then the
1
short screws (107). Torque to 190–220 in-lb (21–25 NSm).
See Torque Sequence, page 32.
2
Arrow (A) must point toward air valve (B).
B
23
101
2
A
1
107
108
1
04620B
Fig. 12
308550
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
4. Unscrew one outer plate (105) from the diaphragm
Reassembly – Standard Diaphragms
1. Grease the shaft u-cup packings (402*) and install
them so the lips face out of the housing (1). See
Fig. 13.
shaft (24). Remove one diaphragm (401), and the
inner plate (104). See Fig. 13.
For overmolded diaphragms: Grip both dia-
phragms securely around the outer edge and
rotate counterclockwise. One diaphragm assembly
will come free and the other will remain attached to
the shaft. Remove the freed diaphragm and air
side plate.
2. Grease the length and ends of the diaphragm shaft
(24) and slide it through the housing (1).
3. Assemble the inner diaphragm plates (104), dia-
phragms (401*), PTFE diaphragms (403*, if pres-
ent), and outer diaphragm plates (105) exactly as
shown in Fig. 13. These parts must be assembled
correctly.
NOTE: PTFE models include a PTFE diaphragm (403)
in addition to the backup diaphragm (401).
5. Pull the other diaphragm assembly and the dia-
phragm shaft (24) out of the center housing (1).
Hold the shaft flats with a 19 mm open–end
wrench, and remove the outer plate (105) from the
shaft. Disassemble the remaining diaphragm
assembly.
4. Apply medium-strength (blue) LoctiteR or equiva-
lent to the threads of the fluid-side plates (105).
Hold one of the outer plates (105) with a wrench,
and torque the other outer plate to 20 to 25 ft-lb
(27 to 34 NSm) at 100 rpm maximum. Do not
over-torque.
For overmolded diaphragms: Pull the other dia-
phragm assembly and the diaphragm shaft (24)
out of the center housing (1). Hold the shaft flats
with a 19 mm open–end wrench and remove the
diaphragm and air side plate from the shaft.
5. Align the fluid covers (101) and the center housing
(1) so the arrows (A) on the covers face the same
direction as the air valve (B). Secure the covers
with the screws (107 and 108), handtight. Install
the longer screws (108) in the top and bottom
holes of the covers. See Fig. 12.
6. Inspect the diaphragm shaft (24) for wear or
scratches. If it is damaged, inspect the bearings
(19) in place. If the bearings are damaged, refer to
page 23.
6. First, torque the longer screws (108) oppositely
and evenly to 190–220 in-lb (21–25 NSm), using a
13 mm socket wrench. Then torque the shorter
screws (107). See Torque Sequence, page 32.
7. Reach into the center housing (1) with an o-ring
pick and hook the u-cup packings (402), then pull
them out of the housing. This can be done with the
bearings (19) in place.
8. Clean all parts and inspect for wear or damage.
Replace parts as needed.
7. Reassemble the ball check valves and manifolds
as explained on page 18.
20
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Reassembly – Overmolded Diaphragms
5. Assemble the other diaphragm assembly to the
shaft as explained in step 2. This diaphragm will
be lifted off the air cover at this point.
WARNING
To reduce the risk of serious injury, including
amputation, do not put your fingers or hand be-
tween the air cover and the diaphragm.
6. Supply the pump with low pressure air (less than 7
psi [0.05 MPa, 0.5 bar]). The diaphragm will very
slowly pull onto the air cover. Find the pressure
that keeps the diaphragm close enough to secure
with the screws, but does not let it contact the pilot
pin.
1. Lubricate and install the shaft u–cup packings
(402*) so the lips face out of the housing (1). See
Fig. 13.
NOTE: Do not deform the diaphragm manually. The
diaphragm needs uniform pressure to deform properly
for maximum life.
2. Assemble the air side plate (104) onto the dia-
phragm (403). The wide, radiused side of the plate
must face the diaphragm. Apply medium–strength
(blue) Loctite or equivalent to the threads of the
diaphragm assembly. Screw the assembly into the
shaft (24) hand–tight.
7. Align the fluid cover (101) and the center housing
(1) so the arrow (A) faces the same direction as
the air valve. Secure the cover with two of the
longer screws (108), handtight.
NOTE: If the diaphragm contacts the pilot pin and is
forced away from the air cover, try Step 5 again. If
necessary, return to Step 3.
3. Grease the length and ends of the diaphragm shaft
(24). Insert the shaft/diaphragm assembly into one
side of the pump. Align the fluid cover (101) and
the center housing (1) so the arrow (A) faces the
same direction as the air valve. Secure the cover
with the screws (107 and 108), handtight.
8. Torque the longer screws (108) oppositely and
evenly to 190–220 in–lb (21–25 NSm), using a
13mm socket wrench. Then torque the shorter
screws (107). See Torque Sequence, page 32.
4. Torque the longer screws (108) oppositely and
evenly to 190–220 in–lb (21–25 NSm), using a
13mm socket wrench. Then torque the shorter
screws (107). See Torque Sequence, page 32.
9. Reassemble the ball check valves and manifolds
as explained on page 18.
308550
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
19
402*
1
105
5
403*
1
1
24
104
401*
2
4
3
2
04708
03982
Cutaway View, with Diaphragms in Place
Cutaway View, with Diaphragms Removed
24
3
104
401*
2
1
403*
2
4
105
5
24
3
1
Lips face out of housing (1).
2
3
4
5
Air Side must face center housing (1).
Grease.
Used on Models with PTFE diaphragms only.
Apply medium-strength (blue) LoctiteR or equivalent.
Torque to 20 to 25 ft-lb (27 to 34 N-m) at 100 rpm maxi-
mum.
04621B
Fig. 13
22
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
7. Use a bearing puller to remove the diaphragm
Bearing and Air Gasket Removal
shaft bearings (19), air valve bearings (12) or pilot
pin bearings (15). Do not remove undamaged
bearings.
Tools Required
D Torque wrench
D 10 mm socket wrench
D Bearing puller
8. If you removed the diaphragm shaft bearings (19),
reach into the center housing (1) with an
o-ring pick and hook the u-cup packings (402),
then pull them out of the housing. Inspect the
packings. See Fig. 13.
D O-ring pick
D Press, or block and mallet
Reassembly
1. If removed, install the shaft u-cup packings (402*)
Disassembly
NOTE: Do not remove undamaged bearings.
so the lips face out of the housing (1).
2. The bearings (19, 12, and 15) are tapered and can
only be installed one way. Insert the bearings into
the center housing (1), tapered end first. Using a
press or a block and rubber mallet, press-fit the
bearing so it is flush with the surface of the center
housing.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 12.
3. Reassemble the air valve as explained on page
17.
1. Relieve the pressure.
2. Remove the manifolds and disassemble the ball
check valves as explained on page 18.
4. Align the new air cover gasket (22) so the pilot pin
(16) protruding from the center housing (1) fits
through the proper hole (H) in the gasket.
3. Remove the fluid covers and diaphragm assem-
blies as explained on page 19.
5. Align the air cover (23) so the pilot pin (16) fits in
the middle hole (M) of the three small holes near
the center of the cover. Install the screws (25),
handtight. See Fig. 14. Using a 10 mm socket
wrench, torque the screws oppositely and evenly
to 130–150 in-lb (15–17 NSm).
NOTE: If you are removing only the diaphragm shaft
bearing (19), skip step 23.
4. Disassemble the air valve as explained on page
16.
5. Using a 10 mm socket wrench, remove the screws
(25) holding the air covers (23) to the center
housing (1). See Fig. 14.
6. Install the diaphragm assemblies and fluid covers
as explained on page 19.
6. Remove the air cover gaskets (22). Always replace
the gaskets with new ones.
7. Reassemble the ball check valves and manifolds
as explained on page 18.
308550
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
1
2
3
Insert bearings tapered end first.
12
Press-fit bearings flush with surface of center housing (1).
2
1
Torque to 130–150 in-lb (15–17 NSm).
1
1
2
1
15
23
16
H
M
Detail of Air Valve Bearings
22
03951
25
3
19
2
1
03952B
Fig. 14
24
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
308550
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Pump Matrix
Husky 2150 Polypropylene and PVDF Pumps, Series A
Your Model No. is marked on the pump’s serial plate. To determine the Model No. of your pump from the following
matrix, select the six digits which describe your pump, working from left to right. The first digit is always D,
designating Husky diaphragm pumps. The remaining five digits define the materials of construction. For example, a
pump with a Husky 2150 aluminum air motor, polypropylene fluid section, polypropylene seats, PTFE balls, and
PTFE diaphragms is Model D F 2 9 1 1. To order replacement parts, refer to the part lists on pages 28–30. The
digits in the matrix do not correspond to the ref. nos. in the parts drawing and lists.
Diaphragm
Pump
Air Motor
Fluid Section
–
Seats
Balls
Diaphragms
232504*
aluminum
polypropylene
–
polypropylene
PTFE
Fluoroelastomer
D (for all pumps) F aluminum
(standard)
1 (not used)
–
–
–
1 (not used)
2 (not used)
3 (316 SST)
1 (PTFE)
1 (PTFE)
24B762*
G aluminum
(remote)
2 (polypropy-
lene)
2 (Acetal)
3 (not used)
2 (not used)
3 (not used)
24B763*
V SST (stan-
dard)
3 (aluminum;
see
manual 308368)
24B764*
4 (SST; see
manual 308368)
–
4 (17–4 PH SST)
4 (440C SST)
4 (not used)
24B765*
24B833*
5 (PVDF)
–
–
–
–
–
5 (TPE)
5 (TPE)
5 (TPE)
6 (Santoprener)
7 (Buna–N)
6 (Santoprener)
7 (Buna–N)
6 (Santoprener)
7 (Buna–N)
8 (Fluoroelastomer) 8 (Fluoroelastomer) 8 (Fluoroelastomer)
9 (polypropylene)
A (PVDF)
–
–
G (Geolastr)
G (Geolastr)
G (Geolastr)
* 232504, Polypropylene 2150 Pump, Series C
Model No. 232504 is a private-label polypropylene
2150 pump. This pump is the same as Model No.
DF2918 except for the label and:
* 24B764 Polypropylene Pump
This pump is the same as Model DF2911 except for
the serial plate and parts listed in the chart below.
Ref. Nos. 10 and 402 are 115666 Packing, U–cup,
Fluoroelastomer
Ref. No. 17 is 168518 O–ring, Fluoroelastomer
Use 243492 as the Air Valve Repair Kit
* 24B765 Polypropylene Pump
This pump is the same as Model DF2311 except for
the serial plate and parts listed in the chart below.
* 24B833 PVDF Pump
This pump is the same as Model DF5A11 except for
the serial plate and parts listed in the chart below.
246452 Stainless Steel Air Motor Conversion Kit
Use kit 246452 and refer to manual 309643 (included
with kit) to convert from aluminum air motor to
stainless steel air motor.
* 24B762 PVDF Plus Pump
This pump is the same as Model DV5A11 except for
Ref.
No.
Part No. Description
Qty
the serial plate and parts listed in the chart at right.
104
15H811
–––
PLATE, air side; alum.
not used
2
105
401
0
2
* 24B763 Polypropylene Plus Pump
This pump is the same as Model DV2911 except for
the serial plate and parts listed in the chart at right.
15G746 DIAPHRAGM, HD, overmolded;
PTFE/EPDM
26
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair Kit Matrix
For Husky 2150 Polypropylene and PVDF Pumps, Series A
Repair Kits may be ordered separately. To repair the air valve, order Part No. 236273 for aluminum center housing
models, or Part No. 255061 for stainless steel housing models (see page 28). Parts included in the Air Valve Repair
Kit are marked with a symbol in the parts list, for example (4{H).
To repair your pump, select the six digits which describe your pump from the following matrix, working from left to
right. The first digit is always D, the second digit is always 0 (zero), and the third is always G. The remaining three
digits define the materials of construction. Parts included in the kit are marked with an asterisk in the parts list, for
example (201*).
For example, if your pump has polypropylene seats, PTFE balls, and PTFE diaphragms, order Repair Kit D 0 G 9
1 1. If you only need to repair certain parts (for example, the diaphragms), use the 0 (null) digits for the seats and
balls, and order Repair Kit D 0 G 0 0 1. The digits in the matrix do not correspond to the ref. nos. in the parts
drawing and lists on pages 28–30.
Diaphragm
Pump
Fluid Section
Material
Null
–
Seats
Balls
Diaphragms
D (for all pumps) 0 (for all pumps) G (Plastic)
–
0 (null)
0 (null)
0 (null)
–
–
–
–
–
–
–
–
–
–
–
1 (not used)
2 (not used)
3 (316 SST)
4 (17–4 PH SST)
5 (TPE)
1 (PTFE)
1 (PTFE)
2 (Acetal)
2 (not used)
3 (not used)
4 (not used)
5 (TPE)
3 (not used)
4 (440C SST)
5 (TPE)
6 (Santoprener)
7 (Buna–N)
6 (Santoprener)
7 (Buna–N)
6 (Santoprener)
7 (Buna–N)
8 (Fluoroelastomer) 8 (Fluoroelastomer) 8 (Fluoroelastomer)
9 (polypropylene)
A (PVDF)
G (Geolastr)
G (Geolastr)
G (Geolastr)
Part No. 253628: Husky 2150 HD Overmolded PTFE/EPDM Diaphragm Repair Kit.
Part No. 289226: Husky 2150 HD Overmolded PTFE/EPDM Diaphragm Repair Kit,
with new air side diaphragm plates.
Part No. 24F399: Husky 2150 PTFE/Santoprene Backer Diaphragm Repair Kit,
for plastic pumps.
308550
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Air Motor Parts List (Matrix Column 2)
Ref.
Digit No.
Ref.
Digit No.
Part No. Description
Qty
Part No. Description
Same as F with the following exceptions
Qty
F
1
2
3
188838
188854
116344
HOUSING, center;
aluminum
1
G
1
195921
HOUSING, center;
remote, aluminum
1
2
COVER, air valve;
aluminum
1
9
23
195919
COVER, air; remote
SCREW, mach, hex
flange hd; M5 x 0.8;
12 mm (0.47 in.)
V
Same as F with the following exceptions
1
15K009
15A735
15H178
HOUSING, center;
stainless steel
1
1
1
188618
188855
108730
188616
188615
188617
112181
188612
188613
104765
115671
GASKET, cover; foam
CARRIAGE; aluminum
O-RING; nitrile
1
1
1
1
1
1
2
2
2
2
2
4{H
5
2
COVER, air valve;
stainless steel
6{H
7{H
8
8J
PLATE, air valve: stain-
less steel
BLOCK, air valve; acetal
PLATE, air valve; sst
SEAL, valve plate; buna-N
PACKING, u-cup; nitrile
PISTON, actuator; acetal
BEARING, piston; acetal
PLUG, pipe; headless
9
–––
–––
–––
2
23
15A742
COVER, air; stainless
steel
9{
10{H
11
12
13}
14}
FITTING, connector;
male
15
188611
188610
157628
188614
188609
116343
188603
189300
189304
115643
BEARING, pin; acetal
PIN, pilot; stainless steel
O-RING; buna-N
2
16
2
2
17{H
18{H
19
BLOCK, pilot; acetal
BEARING, shaft; acetal
SCREW, grounding
1
2
20
1
22
GASKET, air cover; foam
COVER, air; aluminum
SHAFT, diaphragm; sst
2
23
2
24
1
25
SCREW; M8 x 1.25;
25 mm (1 in.)
12
28
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Fluid Section Parts List (Matrix Column 3)
Ref.
5
101
102
103
189795
189789
189792
COVER, fluid; PVDF
2
1
1
Digit No.
Part No. Description
Qty
MANIFOLD, inlet; PVDF
2
101
102
103
104
105
106
107
108
189793
189787
189790
189298
189796
112560
112368
114181
COVER, fluid;
polypropylene
2
MANIFOLD, outlet;
PVDF
MANIFOLD, inlet;
polypropylene
1
104
189298
PLATE, air side;
aluminum
2
MANIFOLD, outlet;
polypropylene
1
105
106
189798
112560
PLATE, fluid side; PVDF
2
8
PLATE, air side;
aluminum
2
SCREW; M8 x 1.25;
70 mm (2.76 in.); sst
PLATE, fluid side;
polypropylene
2
107
108
112368
114181
SCREW; M10 x 1.50;
60 mm (2.36 in.); sst
16
8
SCREW; M8 x 1.25;
70 mm (2.76 in.); sst
8
SCREW; M10 x 1.50;
110 mm (4.33 in.); sst
SCREW; M10 x 1.50;
60 mm (2.36 in.); sst
16
8
110Y 188621
LABEL, warning
MUFFLER
1
1
8
111
112
102656
112559
SCREW; M10 x 1.50;
110 mm (4.33 in.); sst
SCREW; M8 x 1.25;
40 mm (1.57 in.); sst
110Y 188621
LABEL, warning
MUFFLER
1
1
8
113
114
15J379
15J380
WASHER, manifold; out-
let
4
4
111
112
102656
112559
SCREW; M8 x 1.25;
40 mm (1.57 in.); sst
WASHER, manifold; inlet
113
114
15J379
15J380
WASHER, manifold;
outlet
4
4
WASHER, manifold; inlet
308550
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Seat Parts List (Matrix Column 4)
Diaphragm Parts List (Matrix Column 6)
Ref.
Ref.
Digit No.
Part No. Description
SEAT; 316 stainless steel
Qty
Digit No.
Part No. Description
DIAPHRAGM, backup;
Qty
3
201* 189288
4
1
401* not sold
separately polychloroprene (CR)
2
202* 112358
201* 189289
O-RING; PTFE
4
4
402* 112181
PACKING, u-cup; nitrile
DIAPHRAGM; PTFE
DIAPHRAGM; TPE
2
2
2
2
2
4
SEAT; 17–4 stainless
steel
403* 15K313
401* 189295
402* 112181
401* 189296
202* 112358
201* 189292
O-RING; PTFE
SEAT; TPE
4
4
0
4
4
4
0
4
0
4
4
4
4
4
4
5
6
5
6
7
8
9
A
G
PACKING, u-cup; nitrile
202
None
Not Used
DIAPHRAGM; Santo-
prene
201* 189290
202* 112358
201* 15B267
SEAT; Santoprene
O-RING; PTFE
SEAT; Buna–N
Not used
402* 112181
401* 15B313
402* 112181
401* 15B502
PACKING, u-cup; nitrile
DIAPHRAGM; Buna–N
PACKING, u-cup; nitrile
2
2
2
2
7
8
202
201* 15B265
202 None
None
DIAPHRAGM; Fluoroe-
lastomer
SEAT; Fluoroelastomer
Not used
402* 112181
401* 194216
402* 112181
PACKING, u-cup; nitrile
DIAPHRAGM; Geolast
PACKING, u-cup; nitrile
2
2
2
201* 189291
202* 112358
201* 189745
202* 112358
201* 194215
202* 112358
SEAT; polypropylene
O-RING; PTFE
SEAT; PVDF
G
* These parts are included in the pump repair kit, purchased
separately. See Repair Kit Matrix on page 27 to determine
the correct kit for your pump.
O-RING; PTFE
SEAT; Geolast
O-RING; PTFE
Ball Parts List (Matrix Column 5)
Ref.
Digit No.
Part No. Description
Qty
1
2
4
301* 112359
301* 112363
BALL; PTFE
4
BALL; acetal
4
4
301* 112360
BALL; 440C stainless
steel
5
6
7
8
G
301* 112745
301* 112361
301* 15B492
301* 15B491
301* 114753
BALL; TPE
4
4
4
4
4
BALL; Santoprene
BALL; Buna–N
BALL; Fluoroelastomer
BALL; Geolast
30
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
106
113
3
2
103
11 10{
4{H
Y110
H{17
5
104
16
H{18
401*
6{H
7{H
8H
301*
3
403*
1
201*
202*
9{
105
16
1
17{H
1
14 }
107
12
23
25
10{H
11
22
24
15
*402
108
101
19
20
111
*301
*201
13 }
202*
1
102
1
Not used on some models.
04622D
114
112
*
These parts are included in the Pump Repair Kit, which may be purchased separately.
Refer to the Repair Kit Matrix on page 27 to determine the correct kit for your pump.
{
These parts are included in Air Valve Repair Kit 236273 (aluminum center housing mod-
els), which may be purchased separately.
J These parts are included in Air Valve Repair Kit 255061 (stainless steel center housing
models), which may be purchased separately.
Y Replacement Danger and Warning labels, tags and cards are available at no cost.
}
These parts are unique to remote piloted air motor,DG––––
308550
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Torque Sequence
Always follow torque sequence when instructed to torque fasteners.
1. Left/Right Fluid Covers
3. Outlet Manifold
Torque bolts to 190–220 in–lb (21–25 NSm)
Torque bolts to 150–160 in–lb (17–18 NSm)
28
26
1
3
8
5
24
22
10
12
11
9
23
21
6
7
27
25
4
2
SIDE VIEW
TOP VIEW
2. Inlet Manifold
Torque bolts to 150–160 in–lb (17–18 NSm)
20
18
14
15
16
13
19
17
BOTTOM VIEW
32
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
FRONT VIEW
220.5 mm
280.5 mm
1/2 npt(f)
Air Inlet
3/4 npt(f)
Air Exhaust
(muffler
654 mm
included)
578 mm
489 mm
350.5 mm
89 mm
152.5 mm
501.5 mm
SIDE VIEW
PUMP MOUNTING HOLE PATTERN
6.25 in.
(159 mm)
Port Diameter:
2.20 in. (56 mm)
Four 0.625 in.
(16 mm) Diameter Holes
Flange Diameter:
6 in. (152.5 mm)
6.0 in.
(152.5 mm)
Eight 0.75 in.
(19 mm) slots
6.0 in.
(152.5 mm)
45_
6.0 in.
(152.5
mm)
7441A
.5 in.
(13 mm)
12.5 in.
(317.5 mm)
308550
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Maximum fluid working pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 psi
(0.8 MPa, 8 bar)
Air pressure operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20–120 psi
(0.14–0.8 MPa, 1.4–8 bar)
Maximum air consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 scfm
Air consumption at 70 psi/60 gpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 scfm (see chart)
Maximum free-flow delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 gpm (568 l/min)
Maximum pump speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 cpm
Gallons (Liters) per cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.03 (3.90)
Maximum suction lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 ft (5.48 m) wet or dry
Maximum size pumpable solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 in. (6.3 mm)
* Maximum noise level at 100 psi and 50 cpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 dBa
* Sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 dBa
* Noise level at 70 psi and 50 cpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 dBa
Maximum operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150_F (65.5_C)
Air inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 npt(f)
Fluid inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2” Raised Face Flange
Fluid outlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2” Raised Face Flange
Wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vary by Model. See pages 28–30
Non-wetted external parts . . . . . . . . . . . . . . . . . . . . . . . . . . . aluminum, 302 and 316 stainless steel, polyester (labels)
Weight
Polypropylene pumps with Aluminum center section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 lb (22 kg)
PVDF pumps with Aluminum center section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 lb (31 kg)
Polypropylene pumps with stainless steel center section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 lb (32kg)
PVDF pumps with stainless steel center section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 lb (41 kg)
Geolastr and Santoprener are registered trademarks of the Monsanto Co.
Loctiter is a registered trademark of the Loctite Corporation.
*
Noise levels measured with the pump mounted on the floor, using Rubber Foot Kit 236452. Sound power
measured per ISO Standard 9216.
34
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Chart
Example of Finding Pump Air Consumption and Air Pressure at a Specific Fluid Delivery and Discharge Head:
To supply 60 gpm (227 liters) fluid flow (horizontal scale) at 40 psi (0.28 MPa, 2.8 bar) discharge head pressure (vertical scale) re-
quires approximately 60 scfm (1.68 m#/min) air consumption at 70 psi (0.48 MPa, 4.8 bar) inlet air pressure.
feet
(meters)
psi
(MPa, bar)
120
(0.8, 8)
280
A
B
INLET AIR PRESSURES
(85.3)
A
B
C
D
120 psi air (0.8 MPa, 8 bar)
100 psi air (0.7 MPa, 7 bar)
70 psi air (0.48 MPa, 4.8 bar)
40 psi air (0.28 MPa, 2.8 bar)
E
240
100
(0.7, 7)
(73.2)
F
200
80
(61.0)
(0.56, 5.6)
AIR CONSUMPTION
G
E
F
25 scfm (0.70 m#/min)
50 scfm (1.40 m#/min)
75 scfm (2.10 m#/min)
100 scfm (2.80 m#/min)
C
D
160
(48.8)
60
(0.42, 4.2)
G
H
H
120
(36.6)
40
(0.28, 2.8)
80
(24.4)
20
40
(0.14, 1.4)
(12.2)
0
0
30
60
(227)
90
120
150
0
(114)
(341)
(454)
(568)
FLUID FLOW GPM (lpm)
TEST CONDITIONS
Pump tested in water with PTFE diaphragm and inlet
submerged.
KEY
FLUID PRESSURE AND FLOW
SCFM AIR CONSUMPTION
308550
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Warranties
Graco Standard Husky Pump Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of five years from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within six years of the date
of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Extended Product Warranty
Graco warrants all Husky 205, 307, 515, 716, 1040, 1590, 2150, and 3275 air valve center sections to be free from defects in material
and workmanship for a period of fifteen years from date installed in service by the original purchaser. Normal wear of items such as
packings or seals are not considered to be defects in material and workmanship.
Five years
Six to Fifteen years
Graco will provide parts and labor.
Graco will replace defective parts only.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you:
Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 308550
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES S P.O. BOX 1441 S MINNEAPOLIS, MN 55440-1441 S USA
Copyright 1995, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revised 10/2011
36
308550
Download from Www.Somanuals.com. All Manuals Search And Download.
|