Graco Patio Furniture 9651 9744 User Manual

Read all instructions BEFORE  
Failure to follow  
instructions coul  
assembly and use of this product.  
Keep instructions for future use.  
We recommend that you keep these instructions  
with your Pack ’N Play. A storage pocket has been  
provided for them on the bottom panel of your unit.  
Setting Up the Pack ’N Play  
!
THIS PRODUCT REQUIRES ADULT ASSEMBLY.  
!
Keep fingers clear of top corners during setup.  
Be sure Pack ’N Play is completely set up before use.  
Check that the four top rails are completely latched, the  
center of the floor is pushed down, and the mattress is  
flat and secured by the VELCRO® straps. Always follow  
the instructions in the owner’s manual to set up the  
Pack ’N Play.  
®
Pack ’N Play  
®
Bassinet and Canopy  
!
!
When using a bassinet make sure VELCRO patches  
underneath mattress firmly attach to bassinet mesh.  
OWNER’S  
MANUAL  
Before each use, inspect this product for damaged  
hardware, loose joints, missing parts or sharp edges.  
Do not use Pack ’N Play if any parts are missing  
or broken. Call 1-800-345-4109 for replacement parts or  
owner’s manual. Do not substitute parts.  
Using the Pack ’N Play  
!
The Pack ’N Play can be used as a playard, bassinet or  
Model No. _________  
Serial No. _________  
sleeping crib. When used as a playard, never leave child  
unattended and always keep child in view. When used as  
a sleeping crib or bassinet, you must still provide the  
supervision necessary for the continued safety of your  
child.  
Dear Customer,  
Please fill in the model and serial numbers  
above from the label in the center of the  
bottom of your new Pack ’N Play.  
!
Always keep the Pack ’N Play away from hazards in the  
area that may injure your child.  
Model Nos. 9651 & 9744  
!
Do not add padding or other objects inside the Pack ’N  
Play that will permit your child to climb out.  
Congratulations on your purchase of a  
Graco® Pack ’N Play®!  
!
Stop using this product when your child reaches 35 inches  
(89 cm) in height, weighs more than 30 pounds (14 kg), or  
is able to climb out.  
Graco is the recognized leader in the  
design and manufacture of quality baby  
products. We believe your new Graco®  
Pack ’N Play® is a wise choice, promising  
many hours of enjoyment for your baby.  
!
Do not modify Pack ’N Play or add any attachments  
that are not listed in the owner’s manual, including an  
add-on bassinet.  
Your Pack ’N Play® may be used as a playard,  
portable crib, bassinet or canopy unit.  
Using the Bassinet  
!
Use bassinet with only one child at a time.  
Customer Satisfaction  
!
Never place a child under the bassinet.  
Our goal is to make every product the best it  
can be! We are also committed to supporting our  
products after purchase. If you would like to speak  
to Graco about your product, please contact our  
Customer Service Department at 1-800-345-4109  
Our knowledgeable staff will be ready to answer  
any questions you may have concerning parts, use,  
or maintenance. When you call, please have the  
model and serial numbers ready so your call may  
be processed quickly and efficiently.  
Failure to  
instructions coul  
© 1999 Graco 374-7-99  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
At first your Pack ’N Play may be like a new pair of  
shoes. You may need to break it in by slightly stretching  
the netting and fabric. If the center does not stay down,  
place some weight (several books) in the center of the  
unit and let it stand overnight.  
Step 4.  
Install the end of the tube  
without the red spring latch  
by placing the loop end into  
the slot in the plastic corner.  
To Install Your Bassinet  
PARTS LIST  
Step 5.  
On the other end of the tube,  
pull back on the red spring  
latch and insert the loop into  
the slot in the plastic corner.  
CHECK that you have all the parts listed below  
BEFORE assembling your bassinet.  
No tools required.  
The loop ends must be in the slots in the  
corners to secure the bassinet in the Pack ’N Play. Pull  
up on the tube and bassinet to ensure that the tube is  
in place.  
Step 6.  
Repeat steps 4 and 5 on the  
other side of the bassinet.  
Bassinet  
Step 7.  
Loop end  
Tube (2)  
Tube (2)  
Wire end  
Snap both of the end flaps of  
the bassinet to the Pack ’N  
Play with the eight snaps  
(four on each end).  
Round end  
Red spring  
latch end  
Step 8.  
The four bassinet tubes are located in storage pockets  
sewn into the bassinet itself.  
Cover soft side of mattress  
with fitted sheet (on certain  
models) and place the  
mattress in the bassinet  
soft side up. Push down  
on the mattress to secure  
the mattress to the VELCRO®  
on the bassinet.  
Step 1.  
Insert wire end of one tube  
into the round end of a tube  
with a red spring latch.  
Repeat with other tubes.  
DO NOT use your bassinet  
without the mattress  
provided by Graco.  
Step 2.  
Slide the assembled tubes  
into the tunnels on the sides  
of the bassinet.  
To avoid SUFFOCATION, DO NOT use  
extra padding such as a water mattress, mattress, or  
pillows inside the bassinet. Use ONLY mattress  
provided by Graco.  
Step 3.  
Lift bassinet by the two tubes and lower it into the  
Pack ’N Play. Make sure the printed warnings on  
the end flap are facing up.  
To help prevent heat build-up inside  
the playard and to avoid overheating your child, when  
using the bassinet DO NOT use a canopy.  
Your bassinet is now ready to use.  
374-7-99  
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
To Remove Your Bassinet  
Accessory Features  
Step 1.  
SIDE FLAP:  
Remove the mattress from your bassinet.  
You can raise side flap if  
desired.  
Step 2.  
Unfasten VELCRO® straps at  
bottom of flap. Roll flap up.  
Fasten in place with snap  
loops at top.  
Unsnap the end flaps from your Pack ’N Play.  
Step 3.  
Pull back the fabric at one corner of the bassinet to find the  
red spring latch.  
Step 4.  
WHEELS:  
To apply the locks, push  
DOWN on the levers.  
Pull the red spring latch back  
and lift up the tube.  
To release the locks, lift UP  
on the levers.  
Step 5.  
Pull the tube out of the bassinet  
and set aside.  
Step 6.  
TOY BAG:  
Repeat steps 3, 4 and 5 to remove the other tube.  
Toy bag snaps on end of  
unit. Maximum weight  
2 lbs (0.9 kg).  
Step 7.  
Use extreme  
care when pulling the tubes  
apart.  
DO NOT machine wash or dry  
in a dryer. DO NOT dry clean.  
Spot clean with a damp cloth  
and a mild detergent. NO  
BLEACH.  
Pull the tubes apart by twisting  
the tubes as you pull. Store the  
tubes in the pockets in the  
bassinet.  
To Use as a  
Playard/Portable Crib  
Place mattress into your unit  
with padded side up.  
Always use your unit with  
mattress installed soft side up.  
Slide the two VELCRO® straps  
through slots in bottom of Pack  
’N Play and fasten to VELCRO®  
on underside. This will prevent  
mattress from moving.  
Your Pack ’N Play is ready to  
use.  
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 1.  
To Use Your Changing Table  
(on certain models)  
Lay changing table flat on floor with short side in front  
of you and belt facing up. Gently slide one long tube into  
opening on long side exactly as shown.  
Parts List  
CHECK that you have all parts listed below  
BEFORE assembling your changing table.  
Long  
side  
Repeat on other side.  
No tools required.  
Long tube (2)  
Short tube (2)  
Short side  
Step 2.  
Slide one short tube  
into opening on end  
as shown.  
For proper orientation,  
be sure folding side of  
hinge faces pad as  
shown.  
Changing pad  
Changing  
table  
Fold side  
of hinge  
DO NOT insert  
other short tube  
at this time.  
Accessory bag  
Step 3.  
Turn up long tube so  
that its end points down.  
To protect your child from falls and  
other injuries:  
Insert end of long tube  
into opening on end of  
short tube as shown.  
DO NOT slide short  
tube up around the bend  
of long tube until you  
• Always stay within arm’s reach of your child when  
using the changing table. Always use waist belt  
when child is on the changing table. Never leave  
child unattended.  
Short tube side  
• The changing table is designed for use only with  
this Graco Pack ’N Play. Do not attempt to use it  
with any other product. Before each use, make  
sure the changing table is properly secured to  
the Pack ’N Play by pushing down firmly in the  
middle of the changing table. The changing table  
should not fall.  
have finished next step.  
Make sure fabric does  
not get caught in  
opening when inserting  
long tube into short tube.  
• Do not use the changing table as a sleeping or  
play area.  
Step 4.  
• Weight limit for the changing table is 25 pounds  
(11.3 kg). Do not use the changing table as extra  
storage. Always remove the changing table when  
your child is in the Pack ’N Play.  
Repeat step 3 on other  
end of short tube, then  
slide short tube ends up  
onto long tubes.  
• The Pack ’N Play changing table can be used on  
the floor without being attached to the Pack ’N  
Play. Never place the changing table on a piece of  
furniture, bed, counter or any raised surface from  
which the changing table or your child could fall.  
TO AVOID TEARING  
FABRIC, slide this end  
up before proceeding  
with step 4.  
Slide ends up  
374-7-99  
9
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 5.  
To Use Accessory Bag  
Repeat steps 2  
and 3 on other end  
of changing table.  
If your bassinet is already installed, unsnap the four  
snaps on the bassinet end flap from either end of  
Pack ’N Play.  
If the short tubes have  
been inserted correctly,  
the changing table  
should be able to  
Step 1.  
Snap accessory bag  
onto end of Pack ’N  
Play with four snaps  
as shown.  
FOLD UP in the  
center as shown. If you  
cannot fold the tubes  
up in the center, review  
steps 2, 3, and 4.  
Fold up  
Step 6.  
Step 2.  
Place pad in changing  
table with vinyl side up.  
Pull belt straps through  
holes in center of pad.  
Snap bassinet end flap  
over the accessory bag  
with the four snaps.  
To Fold Changing Table  
Step 7.  
Step 1.  
Insert VELCRO® straps  
into the four slots at the  
corners of changing table  
and attach to VELCRO®  
on underside of changing  
table. This will prevent  
pad from moving.  
Pull up on waist belt  
straps to fold.  
Step 2.  
Ends of long tubes  
must point up when  
folded as shown.  
Step 8.  
Place changing table on  
Pack ’N Play as shown.  
You may use your changing  
table with or without your  
bassinet installed. Make  
sure tubes are securely  
over the sides of the  
Ends of tubes  
point up  
Step 3.  
Pack ’N Play.  
To carry or store your changing table  
with your folded Pack ’N Play, see  
To Cover Your Pack ’N Play” section  
in these instructions.  
Check that the changing  
table is supported  
by the Pack ’N Play by  
pushing firmly down into  
center of changing table.  
11  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To Set Up and Use Your Canopy  
When properly used, the canopy provides shade for  
your child. However, your child may be warmer inside  
the playard than in a shaded area outside the playard.  
Canopy  
Tubing  
Step 1.  
To help prevent build-up of heat inside the playard and  
to avoid over-heating your child:  
Unfold the tubing and slide  
the three sections together to  
form one long tube. The  
elastic cord in the tubing will  
hold the pieces together.  
!
Turn canopy mesh away from the sun. Keep entire  
mattress shaded from sunlight at all times.  
!
Keep playard well ventilated:  
!
Always keep the front mesh panel and one side  
mesh panel of the playard open.  
Never cover the canopy mesh.  
Never use the canopy with a bassinet in use.  
!
Step 2.  
!
Slide the long tube into the  
tunnel in the canopy until  
both ends stick out of the  
tunnel 3 or 4 inches  
As always, use good judgment to protect your child  
from exposure to heat which can lead to serious injury  
or death.  
(7.5-10 cm). The tunnel is  
on the shiny side near the  
netting.  
NEVER leave your child unattended.  
ALWAYS keep your child in view.  
Canopy mesh  
Step 3.  
Push the tube ends into  
the corner brackets on the  
Pack ’N Play. Tube end caps  
will snap into place in the  
brackets.  
Front mesh  
panel  
Side mesh  
panel  
The mesh side of the canopy  
goes on the same side of the  
unit as the brackets. The  
shiny side goes on the inside  
of the unit.  
To remove canopy, first  
grasp tube firmly so that it  
will not spring out. Then push  
in on end caps to release  
them from brackets and pull  
tube ends up.  
Push in, then up  
Step 4.  
Pull the back corners of the  
canopy over the back corners  
of the Pack ’N Play and fasten  
the VELCRO® squares located  
on the ends of the top rail and  
back corners of the canopy.  
374-7-99  
13  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 5.  
Step 3.  
To help prevent build-up of heat inside the playard and to  
avoid over-heating your child:  
The top rail has a center piece  
with two tubes hidden under  
the fabric. The button on the  
bottom of the center piece  
releases the two tubes when  
it is pushed up.  
!
Never use the canopy with a bassinet in use.  
!
Turn canopy mesh away from the sun. Keep the entire  
mattress shaded from sunlight at all times.  
!
Keep playard well ventilated:  
!
Always keep the front mesh panel and one side mesh  
panel of the playard open.  
Never cover the canopy mesh.  
!
Canopy mesh  
Side mesh  
panel  
Center  
piece  
Front mesh  
panel  
Tube  
Push UP button  
under fabric  
Maintenance of Canopy:  
DO NOT machine wash or dry in a dryer.  
DO NOT dry clean. Spot clean with a damp  
cloth and a mild detergent. NO BLEACH.  
To fold the top rail:  
!
Lift up slightly on the top rail.  
!
Push up on the button located under the symbol  
!
to release the two tubes.  
®
To Fold Your Pack ’N Play  
!
Push down.  
Step 1.  
!
If top rails do not unlatch, lift  
the center of the floor higher.  
Lower the back flap. Apply  
locks on wheels. Release the  
two VELCRO® straps under the  
Pack ’N Play, and remove the  
mattress.  
!
!
!
Both tubes must be released  
for the top rail to fold.  
Step 2.  
IMPORTANT:  
Raise center halfway  
BEFORE unlocking  
rails.  
Step 4.  
Pull center up all the way.  
Grasp the red handle  
on the center of the floor  
as shown.  
Push down and turn  
handle. Then pull up  
approximately halfway  
to the top rails.  
15  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Step 5.  
To Cover Your Pack ’N Play  
Gather your unit together.  
Do not force.  
Turn unit upside down, so that  
wheels point up. Pull the cover  
over your unit. Make sure carry  
handle attached to Pack ’N Play  
mattress is lined up with zipper.  
Wheel  
Foot  
If unit will not fold, look for a  
partially latched top rail. Squeeze  
the latch button to release the rail.  
Push the plastic end of the bag  
over wheels and feet. Turn unit  
over and pull bag up to cover  
end. Zip together.  
Handle  
Step 6.  
Find the bottom corner belt loop  
(only one). This loop is for holding  
unit and mattress together while  
carrying.  
Models with  
changing table:  
Turn unit upside down, so that  
wheels point up. Pull the cover  
over your unit, making sure  
carry handle attached to  
Pack ’N Play mattress is lined  
up with zipper. Turn unit over.  
Step 7.  
Wrap the mattress around your unit.  
Fasten together the VELCRO® straps,  
attaching the bottom strap to the  
bottom corner belt loop.  
Before pulling bag up, insert  
folded changing table into the  
side opposite the handle as  
shown. Pull bag up to cover  
end. Zip together.  
Handle  
CARE AND MAINTENANCE  
FROM TIME TO TIME CHECK YOUR PACK ’N  
PLAY for worn parts, torn material or stitching.  
Replace or repair the parts as needed. Use only  
Graco® replacement parts.  
IF PACK ’N PLAY IS USED AT THE BEACH, you  
MUST clean sand off your Pack ’N Play, including  
the feet, before packing it into cover. Sand in top  
rail lock may damage it.  
TO CLEAN PACK ’N PLAY, use only household  
soap or detergent and warm water.  
TO WASH CARRY BAG, machine wash in  
lukewarm water on delicate cycle and drip-dry.  
NO BLEACH.  
374-7-99  
17  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts  
Instructions for ordering Pack ’N Play® parts:  
Model Number SHIP TO:  
(Must be filled in)  
Name  
Complete form below. Your Pack ’N Play model number  
MUST be included on the form to ensure proper replacement  
parts. Your model number can be found on a label on the  
center of the bottom of the unit. Payment must accom-  
pany your order.  
Mattress  
Carry bag  
Wheels  
Bassinet  
Wire end tube  
Round end tube  
Canopy  
Canopy tube  
Canopy bracket  
Toy bag  
Long tube  
Short tube  
Changing pad  
Changing table  
Accessory bag  
Fitted sheet  
Address  
City, State, Zip  
(
)
Telephone  
Parts List:  
Price:**  
Mattress ......................$19.00  
Carry bag ................... $13.00  
Wheels ........................$ 7.00 (each)/$10.50 (2)  
Fitted sheet..................$10.00  
Bassinet parts:  
Check enclosed  
(payable to Graco Children’s  
Products Inc.)  
Bassinet ......................$17.00  
Wire end tube .............$ 5.00  
Round end tube ..........$ 5.00  
Canopy parts:  
Canopy ....................... $17.00  
Canopy tube ............... $ 5.00  
Canopy bracket .......... $ 5.00 (each)/$7.50 (2)  
Toy bag .......................$13.00  
Changing table parts:  
Long tube* .................. $ 9.00  
Short tube* ................. $ 7.00  
Changing pad* ........... $10.00  
Changing table* ..........$15.00  
Accessory bag* .......... $ 7.00  
Charge to credit card:  
Visa  
MasterCard  
Discover  
Total:  
Shipping  
& handling:  
$5.00 Account #:  
6% sales tax  
(PA only):  
Expiration date:  
Signature:  
Total amount  
due:  
** Prices subject to change without notice.  
* On certain modelscertain models  
IF YOU NEED HELP  
If you have any questions or if you need any part  
not listed, please call toll-free:  
1-800-345-4109  
Return the form below with payment to:  
GRACO CHILDREN’S PRODUCTS INC.  
CUSTOMER SERVICE DEPARTMENT  
P.O. BOX 100, MAIN STREET  
ELVERSON, PA 19520  
19  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Crib 1762879 User Manual
Graco GPS Receiver GPS 72H User Manual
Grundig VCR GV 460 VPT User Manual
Haier Flat Panel Television LE46H3280 User Manual
Haier Flat Panel Television LET26C430 User Manual
Haier Washer Dryer HWM55 10 User Manual
Honeywell Boiler RVGP User Manual
Honeywell Home Security System HS 6270 User Manual
HP Hewlett Packard Laptop ZV6000 User Manual
HP Hewlett Packard Server QR483A User Manual