LE46H3280
LED
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Star
This product qualifies for ENERGY STAR in the factory default setting and this is the setting in which power savings
will be achieved. Changing the factory default picture setting or enabling other features will increase power
consumption that could exceed the limits necessary to qualify for ENERGY STAR rating.
SYMBOL
SYMBOL DEFINITION
DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electrical shock to persons.
SA 1965
INSTRUCTIONS: The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing) instruction in the
literature accompanying the appliance.
SA 1966
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
Batteries installed warning
Caution - Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the
like.
FOR YOUR SAFETY
Before operating the TV, please read this manual thoroughly. This manual should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy,
and if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE
1. The changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to
this equipment. It is the responsibilities of the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the TV to rain or moisture. Dangerously high voltages are present
inside the TV. Do not open the cabinet. Refer servicing to qualified personnel only.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS AND REMINDERS
Place unit on even surfaces.
Unplug immediately if other
foreign materials are put inside TV
box or if the TV fell down.
Do not cover or block any vents
and openings. Inadequate
ventilation may shorten the life of
the display unit and cause
overheating.
Unplug immediately if
Prohibit/Avoid opening TV
cabinet.
Avoid direct sunlight, dusty,
humid and smoky areas.
malfunction like no video/audio
occurs, or smoke and bad odor
come from TV.
Don't throw any object inside the
TV box like metals or other
flammable materials.
Remember to unplug the AC cord
from the AC outlet before
cleaning. Do not use liquid
cleaners or aerosol cleaners to
clean the display.
Call service personnel to clean the
internal part of the TV once a year.
Don't place the TV in confined
spaces or in a box when using it.
Make sure to unplug the unit
when not in use for a long period
of time (days).
Do not place the display near
water, such as bathtub, washbasin,
kitchen sink, laundry tub,
swimming pool or in a damp
basement.
6 in.
NOTE
Notice for Remote Control
Avoid Dropping
Avoid Liquids
Avoid Aerosol Cleaners
2
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment.
•
To reduce the risk of electric shock or component damage, switch off the power before connecting other
components to your TV.
•
•
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
•
•
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
•
•
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
•
•
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally or
has been dropped.
•
•
Unplug the power cord before cleaning your TV.
When moving your TV from an area of low temperature to an area of high temperature, condensation may form
in the housing. Wait before turning on your TV to avoid causing fire, electric shock, or component damage.
•
•
A distance of at least three feet should be maintained between your TV and any heat source, such as a radiator,
heater, oven, amplifier etc. Do not install your TV close to smoke. Operating your TV close to smoke or moisture
may cause fire or electric shock.
Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable
operation of your TV and to protect it from overheating, be sure these openings are not blocked or covered. Do
not place your TV in a bookcase or cabinet unless proper ventilation is provided.
•
•
•
•
•
Never push any object into the slots and openings on your TV cabinet. Do not place any objects on the top of
your TV. Doing so could short circuit parts causing a fire or electric shock. Never spill liquids on your TV.
Your TV should be operated only from the type of power source indicated on the label. If you are not sure of the
type of power supplied to your home, consult your dealer or local power company.
Do not apply pressure or throw objects at your TV. This may compromise the integrity of the display. The
manufacturer’s warranty does not cover user abuse or improper installations.
The power cord must be replaced when using different voltage than the voltage specified. For more information,
contact your dealer.
When connected to a power outlet, power is always flowing into your TV. To totally disconnect power, unplug
the power cord.
•
•
•
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
The wall socket should be installed near your TV and easily accessible.
Only power of the marked voltage can be used for your TV. Any other voltage than the specified voltage may
cause fire or electric shock.
•
•
•
Do not touch the power cord during lightning. To avoid electric shock, avoid handling the power cord during
electrical storms.
Unplug your TV during a lightning storm or when it will not be used for long period of time. This will protect your
TV from damage due to power surges.
Do not attempt to repair or service your TV yourself. Opening or removing the back cover may expose you to
high voltages, electric shock, and other hazards. If repair is required, contact your dealer and refer all servicing to
qualified service personnel.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
WARNING: Keep your TV away from moisture. Do not expose your TV to rain or moisture. If water penetrates into
your TV, unplug the power cord and contact your dealer. Continuous use in this case may result in fire or electric
shock.
•
•
Do not use your TV if any abnormality occurs. If any smoke or odor becomes apparent, unplug the power cord
and contact your dealer immediately. Do not try to repair your TV yourself.
Avoid using dropped or damaged appliances. If your TV is dropped and the housing is damaged, the internal
components may function abnormally. Unplug the power cord immediately and contact your dealer for repair.
Continued use of your TV may cause fire or electric shock.
•
•
•
Do not install your TV in an area with heavy dust or high humidity. Operating your TV in environments with
heavy dust or high humidity may cause fire or electric shock.
Follow instructions for moving your TV. Ensure that the power cord and any other cables are unplugged before
moving your TV.
When unplugging your TV, hold the AC/DC power adapter, not the cord. Pulling on the power cord may damage
the wires inside the cord and cause fire or electric shock. When your TV will not be used for an extended period
of time, unplug the power cord.
•
•
To reduce risk of electric shock, do not touch the connector with wet hands.
Insert batteries in accordance with instructions. Incorrect polarities may cause the batteries to leak which can
damage the remote control or injure the operator. Do not expose batteries to excessive heat such as sunshine,
fire or the like.
•
If any of the following occurs, contact the dealer:
- The power cord fails or frays.
- Liquid sprays or any object drops into your TV.
- Your TV is exposed to rain or other moisture.
- Your TV is dropped or damaged in any way.
- The performance of your TV changes substantially.
•
•
•
This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
The mains plug or appliance coupler is used as the disconnect device, the disconnect device shall remain readily
operable.
CAUTION - These servicing instructions are for use by qualified service personnel only. To reduce the risk of
electric shock, do not perform any servicing other than that contained in the operating instructions unless you
are qualified to do so.
•
Outdoor Antenna Grounding – If an outside antenna is connected to the receiver, be sure the antenna system is
grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the
National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the
mats and supporting structure grounding of the lead-in wire to an antenna discharge unit, size of grounding
connectors, location of antenna discharge unit, connection to grounding electrodes and requirements for the
grounding electrode. See Figure below.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE
ANTENNA
GROUND CLAMP
ANTENNA DISCHARGE UNIT
ELECTRIC SERVICE EQUIPMENT
GROUND CLAMPS
GROUNDING CONDUCTORS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
Note to the CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article
820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the 6 English grounding system of the building, as close to the point of cable entry
as practical. Please, make sure to connect the power plug to the wall outlet socket after connecting the TV to the
adapter!
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAVE THESE INSTRUCTIONS
Thank you for purchasing this Haier product. This easy-to-use manual will guide you in
getting the best use of your product. Remember to record the model and serial number.
They are on the label on back of the unit.
Model number
Serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty service
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FOR YOUR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
PRECAUTIONS AND REMINDERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PREPARING YOUR LCD TV FOR WALL MOUNTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TURNING ON THE TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PERIPHERAL CONNECTION AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PERIPHERAL CONNECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
MAKING CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CONNECTING TO AN ANTENNA/CABLE WALL JACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CONNECTING EXTERNAL AUDIO/VIDEO DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CONNECTING HEADPHONES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CONNECTING DIGITAL AUDIO DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LEGAL NOTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PRODUCT SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
IMPORTANT: Do not apply pressure to the screen display
area which may compromise the integrity of the display.
The manufacturer’s warranty does not cover user abuse
or improper installations.
TURNING ON THE TV
1. Install the stand and place the TV on a solid surface.
ATTACHING THE STAND
IMPORTANT: The stand of the TV must be assembled
prior to usage.
Min
1 m
1.
(blanket, foam, cloth, etc.) to prevent any damage to
the TV.
2. Carefully align the stand to the bottom of the TV.
3. Fasten the stand using the supplied screws.
NOTE
• Ensure that the TV is placed in a position to allow free
back cover.
• To prevent any unsafe situations, no naked
sources,
such as lighted candles, should be placed on or in the
vicinity.
• Avoid heat, direct sunlight and exposure to rain or water.
The equipment shall not be exposed to dripping or
splashing.
2. Connect the antenna cable or cable TV cable to the
ANT IN aerial socket on the back of the TV set. See
PREPARING YOUR LCD TV FOR WALL MOUNTING
3. Remote control:
We suggest that you keep your TV at least 2.36 inches
(60 mm) from the wall to prevent cable interference.
Before mounting your TV on the wall, you need to
remove the stand.
Remove the cover of the battery compartment.
Insert the 2 supplied batteries (Type AAA 1.5V).
For your safety, please use only with a UL listed wall
mount bracket with minimum weight of the TV without
To attach a wall mount bracket to your TV:
1. Remove the screws holding your TV to the stand.
2. Remove the stand from your TV.
3. Secure the wall mount bracket to the back of your TV
using four screws (see page 18 for the size of the
screws). Follow the instructions of the user manual
that came with the wall mount bracket to install.
4. Power:
Plug the AC power cord into the AC IN jack on the
back of the TV, then plug the other end of the cord
into a working power outlet.
NOTE
5. Turn the TV on:
The wall mount bracket and the screws are not
included.
Press on the remote control or POWER button on
the side control panel of the TV.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIPHERAL CONNECTION AND CONTROLS
PERIPHERAL CONNECTION
SIDE CONTROL
MENU
INPUT
LINE OUT
POWER
#
Item
Description
Connect headphones to this jack.
#
Item
VOL+
VOL-
Description
1
Press to increase the volume level.
Press to decrease the volume level.
1
HEADPHONE When headphones are inserted,
2
3
the TV speakers will be muted.
Press to go to the next channel in
the channel list.
Connect a coaxial audio cable
from a sound bar, stereo system,
receiver, etc.
CH+
CH-
COAXIAL
LINE OUT
USB
2
3
4
Press to go to the previous channel
in the channel list.
4
5
Connect stereo audio cables from
a sound bar, stereo system,
Insert a USB storage device to the
USB port to view JPEG photos,
and listen to MP3 music. (See
page 16 for more information.)
Press to open or close the on-screen
menu.
MENU
INPUT
Press to select the input source.
Press the VOL+ button to change to
the selected input source.
6
7
Connect HDMI devices to these
jacks. An HDMI cable carries both
video and sound. You do not need
to make an audio connection for
an HDMI device. Note: The HDMI2
port is MHL enabled.
HDMI1
5
6
(standby mode). When the TV is
POWER
HDMI2(MHL)
completely disconnect power,
unplug the power cord.
HDMI3
7
Connect the video cable from a
computer.
8
9
VGA
Connect the audio cable from a
computer.
PC AUDIO
RF
Connect an antenna or cable TV
cable to this jack.
10
Connect the video cable for a
composite device.
11 VIDEO
Connect the audio cables for a
component or composite device.
R
L
12
Connect the video cables for a
component device.
13 YPbPr
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MAKING CONNECTIONS
CONNECTING TO AN ANTENNA/CABLE WALL
JACK
CONNECTING PC
RGB
PC
AUDIO
(L/R)
CONNECTING HEADPHONES
CONNECTING EXTERNAL AUDIO/VIDEO DEVICE
Using HDMI cable (best)
MHL
HDMI2
HDMI3
CONNECTING DIGITAL AUDIO DEVICE
NOTE
• An HDMI cable carries both video and audio. You do not
need to use any audio cables.
•
You can connect MHL devices, such as the Roku Streaming
Stick and compatible mobile phones and tablets to the
HDMI2(MHL) port. A USB to HDMI cable is required to
connect a mobile phone or tablet to the TV. Please check
the documentation of your device.
Using component cables (better)
COMPONENT OUT
L
R
Y
P
B
PR
NOTE
making connections.
To play from the external device:
1. Turn on the TV and the connected device.
2. Press INPUT to open the input source list, then press
to highlight the input to which the device was
connected and press OK to switch.
Using composite cable (good)
COMPOSITE OUT
L
R
VIDEO
• Select TV to watch TV from the RF input.
• Select HDMI1, HDMI2(MHL), or HDMI3 to play
from a device connected to the HDMI1,
HDMI2(MHL), or HDMI3 input.
• Select Composite to play from the device
connected to the COMPOSITE input.
• Select Component to play from the device
connected to the COMPONENT input.
• Select VGA to play from the PC connected to the
PC AUDIO inputs.
NOTE
• Cables are often color-coded to match color-coded jacks.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Item
Power
Descriptions
USING THE REMOTE CONTROL
disconnect power, unplug the power cord.
Press to open the input source list.
INPUT
USB
CC
Press to switch to USB input (USB multimedia
mode).
Press this key to select the CC ,ON or OFF
mode and CC on Mute.
Switch to the HDMI2(MHL) input, If the Roku
Streaming Stick is connected, press this
button to return to the Roku home screen.
HOME
0~9 /
number
Press to enter a TV channel number
•
(Press " " to choose the sub-channel).
.
RECALL
Press to switch to last viewed channel.
Press VOL+ or VOL- to adjust volume level.
VOL+/VOL-
MUTE
MENU
Press to open or close the on-screen menu.
Press CH+ or CH- to change TV channels.
CH+/CH -
BACK
Return to the previous menu. If the Roku
Streaming Stick is connected, press this
button to go back to the previous screen.
Press to display the information window.
DISPLAY
EXIT
Press to exit the menu or on screen display
(OSD).
SAP
Press to switch sounds: SAP, Stereo, Mono for
ATV, or switch audio language for DTV.
SLEEP
Press to set the sleep timer.
Press to adjust the picture aspect ratio.
Press to switch the audio mode.
Press to switch the picture mode.
Enter the selected option or perform the
selected operation.
WIDE
AUDIO
PICTURE
OK
CH.LIST
Press to display the Channel List.
FAVORITE
Press to display the Favorite List.
Use the arrow buttons to move around in
menus.
PLAY
Press to start playing the MEDIA, or to pause
playing.(Used for models with MEDIA function
only).
Press to fast reverse MP3 playback in Music
mode.
REV
Press to fast forward MP3 playback in Music
mode.
FWD
Enter electronic program guide. If the Roku
Streaming Stick is connected, press this
button to view more options.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The auto channel scan usually takes a few minutes
to complete but can take up to 20 minutes. You can
cancel the channel scan by pressing EXIT.
INITIAL SETUP
will guide you through setting up basic settings
including the menu language, time zone, and TV
signal source.
Initial Setup
Channel Scan
The channel scan may take a while to complete.
1. Press
to turn on the TV. The setup wizard screen
to select your language, then press
Analog: 0
opens. Press OK to start the wizard.
Digital: 0
2. Press
RF CH: 30
Total Found: 0
to continue.
Initial Setup
Please select your preferred language
Language
20%
Exit
Cancel
English
Français
Español
NOTE
• During initial setup, press
screen and press EXIT to exit the initial setup.
to return to the previous
INPUT SOURCE
Press INPUT to open the input source list, then press
Back
Select
Next
Exit
switch.
to highlight an input and press OK to
3. Press
to select your time zone, then press
to continue.
Initial Setup
Time Zone
Mountain
Newfoundland
Pacific
Alaska
Hawaii
Samoa
Atlantic
Eastern
Central
Back
Select
Next
Exit
4. Press
to select your tuner type, then press
to start channel scan.
Initial Setup
Tuner
NAVIGATING THE ON-SCREEN MENU
1. Press MENU to open the on-screen menu.
Air
2. Press
to select the main menu (Picture/
Cable
Audio/Channel/Setup/Lock), then press OK or
to enter the sub-menu.
3. Press
to highlight a sub-menu item, then
press
to adjust the setting or select the
desired option.
Back
Select
Next
Exit
4. Press EXIT to close the on-screen menu.
NOTE
• Air – Set the signal type to antenna. When set to
Air, the TV can receive analog and digital (ATSC)
broadcasting signals.
• Cable – Set the signal type to cable. When set to
Cable, the TV can receive analog and QAM
broadcasting signals.
• Press MENU to return to the previous menu. If the main
menu is displayed, pressing MENU will close the on-
screen menu.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE
AUDIO
Picture Mode
Brightness
Contrast
Energy Saving
Sound Mode
Balance
Standard
0
Picture
Picture
Audio
50
50
Bass
50
Audio
Channel
Setup
Lock
Color
50
Treble
50
Tint
50
Digital Audio Output Mode
Audio Language
Auto Volume Level
Raw
English
Off
Channel
Setup
Lock
Sharpness
Color Temperature
50
Cool
Select
Exit
Select
Exit
Picture Mode – Select the picture mode. You can select: Sound Mode – Select the sound mode. You can select:
• Standard – A standard picture. The contrast,
brightness, and sharpness are moderately increased.
• Standard – Balanced treble and bass. This setting is
good for watching standard TV broadcasts.
• Vivid – A bright and vivid picture. The contrast,
• Music – Increase the treble and bass and preserve
the original sound. This setting is good for listening
to a musical program.
• Theater – Moderately decrease and enhance treble
and bass for a rich sound experience.
• News – Balance treble and bass. This setting is good
for watching a news program.
brightness, and sharpness are
increased.
• Mild – A soft picture. The brightness, contrast and
sharpness level are lowered.
• User – Customized picture. Picture settings such as
brightness, contrast, and color are manually
adjusted.
• Energy Saving – The backlight brightness is
• User – Let you manually adjust sound settings.
decreased to save energy.
NOTE
NOTE
• Manually adjusting audio settings will automatically
change the Sound Mode to User.
• Manually adjusting picture settings will automatically
change the Picture Mode to User.
Balance – Adjust the balance between the left and right
audio channels.
Brightness – Adjust the brightness of the dark areas of
the picture. Press
to darken the picture. Press
Bass – Adjust the low frequency sound. Press to
to brighten the picture.
decrease bass. Press to increase the bass.
Contrast – Adjust the brightness of the light areas of
the picture. Press to decrease the contrast. Press
to increase the contrast.
Treble – Adjust the high frequency sound. Press
decrease treble. Press to increase the treble.
to
Digital Audio Output Mode – Select digital audio
output type. You can select:
Color – Adjust the color intensity of the picture.
Tint – Adjust the color balance of the picture. Press
•
to increase the red tones. Press to increase
tones.
the green
• Raw – Pass through the original digital audio sound.
• PCM – Output audio in 2-channel stereo.
Sharpness – Adjust the color details of picture. Press
Audio Language – Select an alternate audio language,
if available. You can select English/Spanish/French.
(Digital channels only)
to soften the picture. Press to sharpen the picture.
Color Temperature – Select the color temperature. You
can select:
Auto Volume Level – Adjust the volume to keep the
volume level consistent when switching channels or
when switching from a TV show to a commercial. You
• Normal – Give the white color a neutral tint.
• Warm – Give the white color a reddish tint.
• Cool – Give the white color a bluish tint.
PC Settings – Adjust the computer image in VGA input
(VGA input only). You can adjust:
• H-Pos – Adjust picture’s horizontal position.
• V-Pos – Adjust picture’s vertical position.
• Clock – Adjust the sample frequency.
• Phase – Adjust the focus of stable images.
• Auto – Automatically adjust the image settings.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANNEL
SETUP
Air/Cable
Air
Menu Language
Aspect Ratio
MTS
English
Normal
Mono
On
Picture
Picture
Audio
Auto Scan
Favorite
Audio
Channel
Setup
Lock
Blue Screen
Audio Only
Time
Channel Skip
Channel Number
Channel Label
Off
Channel
Setup
Lock
Noise Reduction
Medium
Select
Exit
Select
Exit
Air/Cable – Select the signal type.
Menu Language – Select on-screen display menu
language. You can select English/Français/Español.
• Air – Set the signal type to antenna. When set to Air,
the TV can receive analog and digital (ATSC)
broadcasting signals.
• Cable – Set the signal type to cable. When set to
Cable, the TV can receive analog and QAM
broadcasting signals.
Aspect Ratio – Select the display mode. You can select:
• Full 100%
image may appear distorted. (VGA input only)
• Point to Point – Display the VGA signal’s original
aspect ratio. Black bars might be added for display.
(VGA input only)
Auto Scan – Press OK to start the auto channel scan.
• Normal – Display the original 4:3 aspect ratio with
Favorite – Manually add and skip channels in your
favorite channel list.
vertical black bars on the left and right of the image.
• Wide – Use this option to view content recorded in a
16:9 (wide-screen) aspect ratio.
Channel Skip – Manually add and skip channels in your
channel list.
• Zoom
and bottom of the image may be cropped.
Channel Number – Select the channel that you want to
assign a customized label.
• Cinema – Stretch the image at the edges, but keeps
a clear image in the center.
MTS – Select the preferred sound track. You can select:
Channel Label – Label a channel to make it easier to
identify.
•
Mono
– Select this option if there is noise or static
from a weak broadcast signal.
•
Stereo – Select this option for programs broadcast in
stereo sound.
Picture
Audio
•
SAP – Select this option to enable audio in an
alternative language, if available.
Channel
Setup
Lock
Blue Screen – When this option is set to
will be blue instead of black when there is no input
signal.
On, the screen
Audio Only
audio.
Select
Exit
NOTE
1. Press OK to label the selected channel.
2. Press
• Audio only works only when the input source is TV and
the TV is receiving a broadcast signal.
• To exit audio only mode, press any button.
3. Press
to select the desired character for a
4. Press OK after all the desired characters are entered.
Time – Adjust the time settings.
Time Zone – Select your time zone.
Sleep Timer – Set the amount of time before the TV
Daylight Saving Time – Select On (if your viewing
area observes Daylight Saving Time) or
(if your
viewing area does not observe Daylight Saving Time).
Clock – Set the date and time.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCK
Noise Reduction – Select the noise reduction mode to
reduce picture noise (snow). You can select
Medium/High.
_ _ _ _
Enter Password
Picture
Audio
Closed Caption – Adjust the closed captioning settings.
CC Mode – Select closed captioning mode. You can
select:
Channel
Setup
Lock
•
• CC On – Turn on closed captioning.
• CC on Mute – Turn on closed captioning when the
sound is muted.
Analog CC – Select analog closed captioning mode.
Digital CC – Select digital closed captioning mode.
Select
Exit
1. Press OK or
to enter password.
Option – Customize digital closed captioning
settings.
2. Use the number buttons on the remote control to
enter your 4-digit password. The default password is
“0000”.
3. After the correct password is entered, the Lock sub-
menu screen opens.
Mode – Select Custom to customize below settings
or select Default to use default settings.
Font Style – Select font style. You can select
Default/Font 0~Font 7.
Change Password
Picture
OK
Font Size – Select font size. You can select Default/
Normal/Large/Small.
Audio
System Lock
US Rating
Off
Font Edge Style – Select font edge style. You can
select Default/None/Raised/Depressed/Uniform/
Left Shadow/Right Shadow.
Channel
Setup
Lock
Canada Rating
RRT Setting
Reset RRT
Font Edge Color – Select font edge color. You can
select Default/Black/White/Red/Green/Blue/Yellow/
Magenta/Cyan.
Select
Exit
FG Color – Select font color. You can select Default/
White/Black/Red/Green/Blue/Yellow/Magenta/
Cyan.
Change Password – Press OK to set a new 4-digit
password.
Enter Old Password – Enter your old 4-digit
password.
BG Color – Select background color. You can select
Default/Black/White/Red/Green/Blue/Yellow
Magenta/Cyan.
Enter New Password – Enter your new 4-digit
password.
FG Opacity – Select font opacity. You can select
Default/Solid/Flashing/Translucent/Transparent.
Password – Enter your new 4-digit password
BG Opacity – Select background opacity. You can
select Default/Solid/Flashing/Translucent/
Transparent.
System Lock – Turn the US and Canada rating limits on
Over Scan – Extend part of the display past the visible
area of the screen. The resulting picture will “zoom in”
on the image center.
Restore Default – Reset all settings to the factory defaults.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MPAA
comes from MPAA rules.
US Rating – Set the U.S. rating limits.
TV – U.S. TV ratings. The TV ratings compose of two
MPAA rating levels
aspects: age-based and content-based.
U.S movie (MPAA) ratings
TV Rating
Picture
G
General audiences.
ALL
PG
Parental guidance suggested.
Audio
Channel
Setup
Lock
FV
V
PG-13
Suitable for children 13 and older.
S
Parental guidance suggested for
children under 17.
L
R
D
NC-17
X
Not suitable for children under 17.
Adults only.
Press OK to Lock or Unlock
Select
Exit
Canada Rating – Set the Canada rating limits.
Canada English – The ratings are for programs using
the English rating system.
Picture
Audio
TV-Y
TV-Y7
TV-G
Canada English rating levels
Canadian English ratings
TV-PG
TV-14
TV-MA
Channel
Setup
Lock
C
Suitable for all children.
Suitable for children 8 and older.
General audiences.
C8+
G
Press OK to Lock or Unlock
Select
PG
14+
18+
Parental guidance suggested.
Suitable for children 14 and older.
Adults only.
Exit
TV rating levels
U.S TV ratings (content-based)
Canada French – The ratings are for programs using
the French rating system.
ALL
FV
V
All ratings
Fantasy violence
Violence
Canada French rating levels
Canadian French ratings
S
Sexual situations
Strong language
Suggestive dialog
G
General audiences.
L
8 ans+
13 ans+
16 ans+
18 ans+
Suitable for children 8 and older.
Suitable for children 13 and older.
Suitable for children 16 and older.
Adults only.
D
U.S TV ratings (age-based)
TV-Y
All children.
TV-Y7
TV-G
Suitable for children 7 and older.
General audiences.
NOTE
• When a rating is locked, that rating and all other higher
ratings are locked. When a rating is unlocked, that rating
and all lower ratings are unlocked.
TV-PG
Parental guidance suggested.
Parental guidance strongly
suggested.
RRT Setting – Adjust RRT settings.
TV-14
Reset RRT – Reset RRT settings to the factory default.
TV-MA
Mature audiences only.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
• Select or press on the remote control to stop
MEDIA
slide show playback.
The USB Media Player allows you to connect a USB
device to your TV and play music or photos.
• Select to change repeat mode. You can select
Repeat One/Repeat ALL/None.
• Select to play the music in the current folder. To
stop the music playback, highlight and press
OK again.
1. Connect your USB device to the USB port on the rear
of the TV.
• Select to display the play list. Press EXIT to close
the list.
• Select
resolution, size, date and time. Press OK to close
the information screen.
• Select to rotate the photo 90° clockwise.
• Select to rotate the photo 90° counterclockwise.
• Select to zoom in on the photo.
• Select to zoom out on the photo.
• Select to view a zoomed photo. Press
on the remote control to move and view the photo
in detail. Press EXIT to exit.
2. Press INPUT and select USB, or press USB on the
remote control to switch to USB input.
USB 2.0
Music
Title:
005
N/A
N/A
2012
Artist:
Album:
Year:
Photo
Music
Bit Rate: 186K
Sampling: 44K
Size:
5027KBytes
OK
Select
OK
00:00:20
00:03:40
Music
Pause
Repeat ALL
005.mp3
3. Press
press OK.
to highlight Photo or Music, then
to highlight C, then press OK to
Press
1. Press
to execute.
to highlight an option, then press OK
• Select
/
or press
on the remote control to
4. Press
to select the
that you want to
to highlight
pause or resume music playback.
play, then press OK.
• Select
reverse music playback.
• Select or press
forward music playback.
or press
on the remote control to fast
5. To navigate the playback, press
an option on the operation banner, then press OK
to execute.
on the remote control to fast
Photo
• Select
to play
• Select
to play
• Select or press on the remote control to stop
music playback.
• Select to change repeat mode. You can select
Repeat One/Repeat ALL/None.
• Select to display the song list. Press EXIT to close
the song list.
Photo
Repeat ALL
IMG_7777.JPG
NOTE
• In photo and music mode, press EXIT to close the
operation banner, and press OK to open it again.
Pause
• In music mode, before pressing
to adjust the
1. Press
to execute.
to highlight an option, then press OK
volume level, press EXIT to close the operation
• Select
/
or press
on the remote control to
pause or resume slide show playback.
• Select
• Select
to display the previous photo.
to display the next photo.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TIPS
LEGAL NOTICES
Modifications
Care of the screen
Do not rub or strike the screen with anything hard as
this may scratch, mar, or damage the screen
permanently.
Unplug the power cord before cleaning the screen. Dust
the TV by wiping the screen and the cabinet with a soft,
clean cloth. If the screen requires additional cleaning,
use a clean, damp cloth. Do not use liquid cleaners or
aerosol cleaners.
The FCC requires the user to be notified that any
changes or modifications made to this device that are
not expressly approved by our company may void the
user’s authority to operate the equipment.
Cables
Connections to this device must be made with shielded
cables with metallic RF/EMI connector hoods to
maintain compliance with FCC Rules and Regulations.
Mobile telephone warning
Canada ICES-003 statement
To avoid disturbances in picture and sound,
malfunctioning of your TV or even damage to the TV,
keep your mobile telephone away from the TV.
This Class B digital apparatus complies with Canadian
ICES-003. Standard Television Receiving Apparatus —
Appareil de réception télévision ordinaire, Canada BETS-
7/NTMR-7.
End of life directives
We are paying a lot of attention to produce
environmentally friendly products. Your new television
contains materials, which can be recycled and reused.
Canadian notice
This Class B digital apparatus meets all requirements of
the Canadian Interference-Causing Equipment
Regulations.
At the end of its life, specialized companies can
dismantle the discarded receiver to collect the
reusable materials and to minimize the amount of
materials to be disposed of.
Avis Canadian
Cat apparel numerous de la classed B respected toutes
les exigencies du règlement sur le materiel brouilleur du
Please ensure you dispose of your old receiver
according to local regulations. Haier is committed to
safely recycling electronic products and product
materials. Please check for a local recycling location in
the United States at: 1800RECYCLING.COM.
Canada.
HDMI, the HDMI logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LCC in the United States and other
countries.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT SPECIFICATION
NOTE
• T
•
• T
Model
LE46H3280
DISPLAY
Viewable
46”
Television System
Channel Coverage
NTSC, ATSC
NTSC: CH2-CH69 (Antenna)/CH1-CH135 (Cable)
ATSC: CH2-CH69 (Antenna)/CH1-CH135 (Cable)
CONNECTIONS
Rear Connectors
Side Connectors
HEADPHONE
COAXIAL
LINE OUT
USB
HDMI1/HDMI2(MHL)/HDMI3
VGA
PC AUDIO
RF
VIDEO
R
L
YPbPr
WEIGHT & DIMENSION
Dimensions with Stand (W x H x D)
42.05" x 27.48" x 8.74"
Dimensions without Stand (W x H x D) 42.05" x 25.39" x 2.60"
Weight with Stand
29.9 lbs
24.4 lbs
Weight without Stand
WALL MOUNTING
Wall Mount Pattern (H x V)
Screw type
400 x 200 mm
M6
POWER
Power Consumption
Standby
120W
< 1W
Mains Power
100-240V~50/60Hz
10W+10W
Audio Power
Ambient Temperature
41°F ~ 95°F
PACKAGE CONTENTS
Package Contents
TV unit x 1
TV stand x 1
Remote control x 1
Screws x 4
User manual x 1
Registration card x 1
AC power cord x 1
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Please make these simple checks before calling service. These tips may save you time and money since charges for
receiver installation and adjustments of customer controls are not covered under your warranty.
Symptoms
Items to Check and Actions to Follow
“Ghost” or double image
• This may be caused by obstruction to the antenna due to high rise
buildings or hills. Using a highly directional antenna may improve the
picture.
No power
No picture
• Check if the TV’s AC power cord is plugged into the outlet.
• Unplug the TV, wait for 60 seconds. Then reinsert plug into the outlet
and turn on the TV again.
• Check antenna connections at the rear of the TV to see if it is properly
connected to the TV.
• Possible broadcast station trouble. Try another channel.
• Adjust the contrast and brightness settings.
• Check the Closed Captions control. Some TEXT modes could block the
screen.
Good picture but no sound
• Increase the volume level by pressing the VOL+ button on the remote
control or on the TV side control panel.
• Press the MUTE
Good sound but poor color
Poor picture
• Adjust the contrast, color and brightness settings.
• Poor picture quality may occur when an activated S-VHS camera or
camcorder is connected to your TV and other peripherals at the
Snowy picture and noise
Horizontal dotted line
• Check the antenna connection.
• This may be caused by electrical interference (e.g. hair dryer, nearby
Television not responding to
remote control
• Check whether the batteries are working. Replace if necessary.
• Clean the remote control sensor lens on the TV.
• You can still use the buttons on the side of your TV.
Pixels (dots) that are always
dark or always lit
• Your TV is precision-manufactured using an extremely high level of
technology. However, sometimes pixels may not display correctly.
These types of occurrences are inherent to this type of product and do
not constitute a defective product.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
This Haier brand product, when shipped in its original container, will be free from defective workmanship
and materials, and agrees that it will, at its option, either repair the defect or replace the defective product
with a new or re-manufactured equivalent, for parts or labor for the periods set forth below:
This warranty does not apply to the appearance of the product or the exterior of the product, which has
additional excluded items set forth below:
The warranty commences on the date the item was purchased and the original purchase receipt must be
presented to the authorized service center before warranty repairs are rendered.
The limited warranty described herein is in addition to whatever implied warranties may be granted to
purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR USE ARE LIMITED TO THE PERIOD(s) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some
states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other
than those described herein, or to extend the duration of any warranties beyond the time period
described herein on behalf of Haier.
The warranties described herein shall be the sole and exclusive warranties granted by Haier and shall be
the sole and exclusive remedy available to the purchaser. Correction of defects in the manner and for the
Haier to the purchaser with respect to the product, and shall constitute full satisfaction of all claims,
whether based on contract, negligence, strict duality or otherwise. In no event shall Haier be liable, or in
any way responsible for any damages or defects in the product which were caused by repairs or
attempted repairs performed by anyone other than an authorized service center or dealer; nor shall Haier
be liable, or in any way responsible for incidental or consequential economic or property damage. Some
states do not allow the exclusion of incidental or consequential damages, so that above exclusion may not
apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
Warranty period for LE46H3280 one year parts and labor.
Additional items excluded from warranty coverage: non-rechargeable batteries. What to do to obtain
service or to obtain product literature, accessories, supplies or customer assistance: Simply call 1-877-337-
3639. Be sure to have proof of purchase.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Made in China
Printed China
Haier America
New York, NY 10018
Model: LE46H3280
Issued: Jul. 2013
Fabriqué en Chine
Hecho en China
La Chine imprimée
China impresa
©2013 Haier America Trading, LLC.
Download from Www.Somanuals.com. All Manuals Search And Download.
|