Operation
Husky ™ 1050HP 2:1
334014A
Air-Operated Diaphragm Pump
EN
1–inch high-pressure pump with modular air valve for fluid transfer applications. For professional use
only.
Important Safety Instructions
Read all warnings and instructions in this manual and in your
Repair/Parts manual. Save these instructions.
Maximum Fluid Working Pressure:
200 psi (1.38 MPa, 13.8 bar)
Maximum Air Input Pressure:
100 psi (0.69 MPa, 6.9 bar)
PROVEN QUALITY. LEADING TECHNOLOGY.
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Information
To Find Your Nearest Distributor
Distributor Note
1. To find part numbers for replacement parts:
2. Click on Where to Buy and use the Distributor
Locator.
a. Use the 20–digit number from the ID plate
on the pump.
b. Use the Configuration Number Matrix on the
next page to understand which parts are
described by each digit.
To Specify the Configuration of a New
Pump
c. Use the Repair/Parts Manual. Refer to the
main Parts illustration and to the Parts/Kits
Quick Reference. Follow the page references
on these two pages for further ordering
information, as needed.
Please call your distributor.
To Order Replacement Parts
2. Please call Graco Customer Service to order.
Please call your distributor.
334014A
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Number Matrix
Check the identification plate (ID) for the 20–digit
Configuration Number of your pump. Use the
following matrix to define the components of your
pump.
Sample Configuration Number:
1050HP A01A
A1
SS SP SP
PT
Pump Model
Center Section Manifolds
and Air Valve
Seats Balls
Diaphragms
Manifold
O-Rings
Pump
Center Section and Air Valve Air Valve
Material
Manifolds
Aluminum
Standard
Aluminum, standard ports, npt
Aluminum, standard ports, bsp
Stainless steel, standard ports, npt
Stainless steel, standard ports, bsp
1050HP
A01A
A1
A2
S1
S2
Aluminum
Check Valve Seats
316 Stainless Steel
Check Valve Balls
Diaphragm Material
Manifold O-Rings
Santoprene
Santoprene
PTFE
SS
SP
SP
PT
4
334014A
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The
exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific
risks. When these symbols appear in the body of this manual or on warning labels, refer back to these
Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout
the body of this manual where applicable.
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help
prevent fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and
plastic drop cloths (potential static arc).
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords, or turn power or light switches on or off when flammable
fumes are present.
• Ground all equipment in the work area. See Grounding instructions.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless
they are antistatic or conductive.
• Stop operation immediately if static sparking occurs or you feel a shock. Do not use
equipment until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
• Route exhaust away from all ignition sources. If diaphragm ruptures, fluid may be exhausted
with air.
PRESSURIZED EQUIPMENT HAZARD
Fluid from the equipment, leaks, or ruptured components can splash in the eyes or on skin
and cause serious injury.
• Follow the Pressure Relief Procedure when you stop spraying/dispensing and before
cleaning, checking, or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
334014A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated
system component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data
in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete
information about your material, request MSDS from distributor or retailer.
• Do not leave the work area while equipment is energized or under pressure.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine
manufacturer’s replacement parts only.
• Do not alter or modify equipment. Alterations or modifications may void agency approvals
and create safety hazards.
• Make sure all equipment is rated and approved for the environment in which you are using it.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
THERMAL EXPANSION HAZARD
Fluids subjected to heat in confined spaces, including hoses, can create a rapid rise in pressure
due to the thermal expansion. Over-pressurization can result in equipment rupture and serious
injury.
• Open a valve to relieve the fluid expansion during heating.
• Replace hoses proactively at regular intervals based on your operating conditions.
PLASTIC PARTS CLEANING SOLVENT HAZARD
Many solvents can degrade plastic parts and cause them to fail, which could cause serious
injury or property damage.
• Use only compatible water-based solvents to clean plastic structural or pressure-containing
parts.
• See Technical Data in this and all other equipment instruction manuals. Read fluid and
solvent manufacturer’s MSDSs and recommendations.
6
334014A
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin,
inhaled, or swallowed.
• Read MSDSs to know the specific hazards of the fluids you are using.
• Route exhaust away from work area. If diaphragm ruptures, fluid may be exhausted into
the air.
• Store hazardous fluid in approved containers, and dispose of it according to applicable
guidelines.
BURN HAZARD
Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid
severe burns:
• Do not touch hot fluid or equipment.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent serious injury,
including eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective
equipment includes but is not limited to:
• Protective eyewear, and hearing protection.
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent
manufacturer.
334014A
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
only a guide for selecting and installing system
components. Contact your Graco distributor for
assistance in planning a system to suit your needs.
Grounding
Tighten Fasteners Before Setup
The equipment must be grounded to reduce the
risk of static sparking. Static sparking can cause
fumes to ignite or explode. Grounding provides an
escape wire for the electric current.
Before using the pump for the first time, check
and retorque all external fasteners. Follow
operation, retorque the fasteners.
• Pump: Loosen the grounding screw (GS). Insert
one end of a 12 ga. minimum ground wire (R)
behind the grounding screw and tighten the screw
securely. Connect the clamp end of the ground
wire to a true earth ground. A ground wire and
clamp, Part 238909, is available from Graco.
Mounting
• The pump exhaust air may contain
contaminants. Ventilate to a remote
• Never move or lift a pump under pressure. If
dropped, the fluid section may rupture. Always
before moving or lifting the pump.
1. Be sure the mounting surface can support the
weight of the pump, hoses, and accessories, as
well as the stress caused during operation.
2. For all mountings, be sure the pump is bolted
directly to the mounting surface. Mount the pump
horizontally, with the feet at the bottom of the
pump. Do not mount the pump on a vertical
surface, such as a wall.
Figure 1 Grounding Screws and Wires
3. For ease of operation and service, mount the
pump so air valve, air inlet, fluid inlet and fluid
outlet ports are easily accessible.
8
334014A
Download from Www.Somanuals.com. All Manuals Search And Download.
• Air and fluid hoses: Use only grounded hoses
with a maximum of 500 ft (150 m) combined hose
length to ensure grounding continuity.
gauge to control the fluid pressure. The fluid stall
pressure will be the same as the setting of the
air regulator.
• Air compressor: Follow manufacturer’s
recommendations.
2. Locate a bleed-type master air valve (B) close to
the pump and use it to relieve trapped air. Be
sure the valve is easily accessible from the pump
and located downstream from the regulator.
• Fluid supply container: Follow your local code.
• Solvent pails used when flushing: Follow your
local code. Use only conductive metal pails
placed on a grounded surface. Do not place the
pail on a nonconductive surface, such as paper
or cardboard, which interrupts the grounding
continuity
Trapped air can cause the pump to cycle
unexpectedly, which could result in serious
injury from splashing.
Check your system electrical continuity after the
initial installation, and then set up a regular schedule
for checking continuity to be sure proper grounding
is maintained.
3. Locate another master air valve (E) upstream
from all air line accessories and use it to isolate
them during cleaning and repair.
4. An adjustable inlet air valve or needle valve (G)
my be installed for pump speed control.
Air Line
5. Install a grounded, flexible air hose (A) between
the accessories and the 3/4 npt(f) pump air inlet
(D). Use a minimum 5/8 in. (16 mm) ID air hose.
1. Install an air filter/regulator (C). An air line filter
removes harmful dirt and moisture from the
compressed air supply. Use the regulator and
334014A
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Exhaust Ventilation
2. Install a grounded air exhaust hose (U). Connect
the muffler (T) to the other end of the hose. The
minimum size for the air exhaust hose is 3/4 in.
(19 mm) ID. If a hose longer than 15 ft (4.57 m)
is required, use a larger diameter hose. Avoid
sharp bends or kinks in the hose.
The air exhaust port is 3/4 npt(f). Do not restrict the
air exhaust port. Excessive exhaust restriction can
cause erratic pump operation.
3. Place a container at the end of the air exhaust
line to catch fluid in case a diaphragm ruptures.
If the diaphragm ruptures, the fluid being pumped
will exhaust with the air.
To provide a remote exhaust:
1. Remove the muffler (T) from the pump air
exhaust port.
Figure 2 Vent exhaust air
KEY
A
Air supply line
G Optional needle valve for pump speed
adjustment.
B
C
D
E
Bleed-type master air valve
Air filter/regulator
T
U
V
Muffler
Grounded air exhaust hose
Container for remote air exhaust
Air inlet
Master air valve (for accessories)
10
334014A
Download from Www.Somanuals.com. All Manuals Search And Download.
Fluid Supply Line
Fluid Outlet Line
1. Use grounded flexible, fluid supply hoses (G).
1. Use grounded, flexible fluid hoses (L). See
2. If the inlet fluid pressure to the pump is more
than 25% of the outlet working pressure, the ball
check valves will not close fast enough, resulting
in inefficient pump operation.
2. Install a fluid drain valve (J) near the fluid outlet.
3. Install a shutoff valve (K) in the fluid outlet line.
3. Excessive inlet fluid pressure also will shorten
diaphragm life. Approximately 3 - 5 psi (0.02-
0.03 MPa, 0.21-0.34 bar) should be adequate
for most materials.
Fluid Inlet and Outlet Ports
NOTE: Remove and reverse the manifold(s) to
change the orientation of inlet or outlet port(s). Follow
4. For maximum suction lift (wet and dry), see
always install the pump as close as possible to
the material source.
1050HP — Aluminum Manifolds
The fluid inlet and outlet manifolds each have two 1
in. npt(f) or bspt threaded ports (M, N). Close off the
unused port using the supplied plugs.
1050HP — Stainless Steel Manifolds
The fluid inlet and outlet manifolds each have one
1 in. npt(f) or bspt port.
334014A
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Floor Mount Installation
Figure 3 Typical floor mount installation
KEY
A
B
Air supply line
J
Fluid drain valve (required)
Fluid shutoff valve
Bleed-type master air valve (required for
pump)
K
C
D
Air filter and regulator
Air inlet
L
Flexible fluid outlet hose
M
Fluid inlet (2 ports on aluminum manifolds,1
port on SST manifolds)
E
F
Master air valve (for accessories)
Flexible fluid suction hose
N
R
Fluid outlet (2 ports on aluminum manifolds,1
port on SST manifolds)
Ground wire (required; see
G
Optional needle valve for pump speed
adjustment.
12
334014A
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Pressure Relief Procedure
4. Open the fluid drain valve (installed on the
system) to relieve all fluid pressure. Have a
container ready to catch the drainage.
Follow the Pressure Relief Procedure
whenever you see this symbol.
Tighten Fasteners Before Setup
Before using the pump for the first time, check
and retorque all external fasteners. Follow
Torque Instructions, page 16. After the first day of
operation, retorque the fasteners.
This equipment stays pressurized until pressure
is relieved manually. To help prevent serious
injury from pressurized fluid, such as splashing
in the eyes or on skin, follow the Pressure Relief
Procedure when you stop pumping and before you
clean, check, or service the equipment.
Flush the Pump Before First Use
The pump was tested in water. If water could
contaminate the fluid you are pumping, flush the
pump thoroughly with a compatible solvent. See
1. Shut off the air supply to the pump.
2. Open the dispensing valve, if used.
3. Shift the high/low pressure lever back and forth
two times. Leave the lever in the “Low” position
as shown.
High/Low Lever
Use the High/Low lever to set the desired pressure
mode. When the lever is set to “Low,” the fluid outlet
pressure is slightly less than the air inlet pressure.
When the lever is set to “High,” the fluid outlet
pressure is slightly less than two times the inlet
air pressure. Note that the High pressure setting
increases both fluid outlet pressure and inlet air
consumption.
NOTE: The lever must be fully seated into the High
or Low position for proper operation.
Figure 4 High/Low Pressure Lever
334014A
13
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Slowly increase air pressure with the air regulator
until the pump starts to cycle. Allow the pump to
cycle slowly until all air is pushed out of the lines
and the pump is primed.
Start and Adjust the Pump
1. Be sure the pump is properly grounded. Refer
NOTE: Use lowest possible air pressure to prime,
just enough to cycle the pump. If the pump does
not prime as expected, turn air pressure DOWN.
2. Ensure the High/Low pressure lever is in the
“Low” position before starting the pump.
3. Check all fittings to be sure they are tight. Use
a compatible liquid thread sealant on all male
threads. Tighten fluid inlet and outlet fittings
securely.
10. If you are flushing, run the pump long enough to
thoroughly clean the pump and hoses.
11. Close the dispensing valve, if used.
12. Close the bleed-type master air valve.
4. Place the suction tube (if used) in the fluid to be
pumped.
NOTE: If fluid inlet pressure to the pump is more
than 25% of outlet working pressure, the ball
check valves will not close fast enough, resulting
in inefficient pump operation.
Pump Shutdown
NOTICE
Excessive fluid inlet pressure can reduce
diaphragm life and may result in pump damage.
At the end of the work shift and before you check,
adjust, clean or repair the system, follow the
5. Place the end of the fluid hose into an appropriate
container.
6. Close the fluid drain valve.
7. Turn the air regulator knob to 0. Open all
bleed-type master air valves.
8. If the fluid hose has a dispensing device, hold
it open.
14
334014A
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Maintenance Schedule
Flushing and Storage
Establish a preventive maintenance schedule,
based on the pump’s service history. Scheduled
maintenance is especially important to prevent spills
or leakage due to diaphragm failure.
• Flush before fluid can dry in the equipment, at the
end of the day, before storing, and before repairing
equipment.
Lubrication
The pump is lubricated at the factory. It is designed
to require no further lubrication for the life of the
pump. An inline lubricator is not needed, and is not
recommended, under normal operating conditions.
• Flush at the lowest pressure possible. Check
connectors for leaks and tighten as necessary.
• Flush with a fluid that is compatible with the fluid
being dispensed and the equipment wetted parts.
Flush the pump often enough to prevent the fluid you
are pumping from drying or freezing in the pump and
damaging it. Use a compatible solvent.
Tighten Threaded Connections
Before each use, check all hoses for wear or
damage, and replace as necessary. Check to be
sure all threaded connections are tight and leak-free.
Check fasteners. Tighten or retorque as necessary.
Although pump use varies, a general guideline
is to retorque fasteners every two months. See
Always flush the pump and relieve the pressure
before storing it for any length of time.
334014A
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Torque Instructions
NOTE: All fasteners for the fluid covers, center
diaphragm joint, and manifolds have a thread-locking
adhesive patch applied to the threads. If this patch is
excessively worn, the fasteners may loosen during
operation. Replace screws with new ones or apply
medium-strength (blue) Loctite or equivalent to the
threads.
Fluid cover, center diaphragm joint, and manifold
fasteners: 100 in-lb (11.3 N•m)
Lubricate air valve fasteners prior to reassembly to
prevent galling. Retorque the air valve fasteners in a
crisscross pattern to specified torque.
Air valve fasteners: 80 in-lb (9.0 N•m)
If fluid cover, center diaphragm joint, or manifold
fasteners have been loosened, it is important to
torque them using the following procedure to improve
sealing.
NOTE: Always completely torque the fluid covers and
center diaphragm joint before torquing the manifolds.
Start all fluid cover or center diaphragm joint screws a
few turns. Then turn down each screw just until head
contacts cover. Then turn each screw by 1/2 turn
or less working in a crisscross pattern to specified
torque. Repeat for manifolds.
Air Valve Fasteners
Fluid Covers and Center Diaphragm Joint
Manifolds
16
334014A
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Mounting
KEY
Aluminum
SST
Aluminum and SST
6.2 in (157 mm)
9.4 in (239 mm)
15.6 in (396 mm)
3/4 npt(f) Air Inlet
A
B
C
D
E
12.7 in (323 mm)
14.4 in (366 mm)
15.3 in (389 mm)
10.9 in (277 mm)
1.8 in (46 mm)
11.8 in (300 mm)
12.9 in (328 mm)
13.7 in (348 mm)
9.5 in (241 mm)
1.1 in (28 mm)
H
J
K
L
M
1 in npt(f) or 1 in. bspt Fluid Inlet
(2 for aluminum manifolds; 1 for SST manifolds)
1 in npt(f) or 1 in. bspt Fluid Outlet
(2 for aluminum manifolds; 1 for SST manifolds)
3/4 npt(f) Air Exhaust Port
F
10.8 in (274 mm)
10.7 in (272 mm)
N
P
G
21.5 in (546 mm)
20.6 in (523 mm)
NOTE: All dimensions are approximate.
334014A
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Charts
Low Pressure Setting
Fluid Pressure
Approximate Cycles per Minute
56
112
168
224
280
100
(0.70, 7.0)
80
(0.55, 5.5)
A
B
Operating Air Pressure
A
100 psi (0.7 MPa, 7.0 bar)
60
(0.41, 4.1)
PSI
(MPa, bar)
40
(0.28, 2.8)
B
70 psi (0.48 MPa, 4.8 bar)
C
D
20
(0.14, 1.4)
C
40 psi (0.28 MPa, 2.8 bar)
0
0
10
(38)
20
(76)
30
(114)
40
(151)
50
(189)
D
20 psi (0.14 MPa, 1.4 bar)
Fluid Flow — gpm (lpm)
How to Read the Charts
Air Consumption
1. Locate fluid flow rate along
bottom of chart.
Approximate Cycles per Minute
56
112
168
224
280
75
(2.1)
2. Follow vertical line up to
intersection with selected
operating air pressure
curve.
60
(1.7)
3. Follow left to scale to read
fluid outlet pressure (top
chart) or air consumption
(bottom chart)
45
(1.3)
A
B
scfm
(Nm3/min.)
30
(0.8)
C
D
15
(0.4)
0
0
10
20
30
40
50
(38)
(76)
(114)
(151)
(189)
Fluid Flow — gpm (lpm)
18
334014A
Download from Www.Somanuals.com. All Manuals Search And Download.
High Pressure Setting
Fluid Pressure
Approximate Cycles per Minute
50
100
150
200
250
200
(1.38, 13.8)
160
(1.10, 11.0)
Operating Air Pressure
120
(0.83, 8.3)
A
B
PSI
(MPa, bar)
A
100 psi (0.7 MPa, 7.0 bar)
80
(0.55, 5.5)
B
70 psi (0.48 MPa, 4.8 bar)
40
C
D
(0.28, 2.8)
C
40 psi (0.28 MPa, 2.8 bar)
0
0
10
(38)
20
(76)
30
(114)
40
(151)
50
(189)
D
20 psi (0.14 MPa, 1.4 bar)
Fluid Flow — gpm (lpm)
How to Read the Charts
Air Consumption
1. Locate fluid flow rate along
bottom of chart.
Approximate Cycles per Minute
50
100
150
200
250
120
(3.4)
2. Follow vertical line up to
intersection with selected
operating air pressure
curve.
96
(2.7)
3. Follow left to scale to read
fluid outlet pressure (top
chart) or air consumption
(bottom chart)
A
B
72
(2.0)
scfm
(Nm3/min.)
48
(1.4)
C
D
24
(0.7)
0
0
10
20
30
40
50
(38)
(76)
(114)
(151)
(189)
Fluid Flow — gpm (lpm)
334014A
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
US
Metric
Maximum fluid working pressure
Air pressure operating range
Fluid displacement per cycle
Low Pressure Setting
High Pressure Setting
Air consumption
200 psi
20-100 psi
1.4 MPa,14.0 bar
0.14-0.69 MPa, 1.4-6.9 bar
0.17 g
0.20 g
at 70 psi, 20 gpm
26 scfm
0.64 l
0.76 l
at 4.8 bar, 76 lpm
0.7 cubic meters per minute
1.4 cubic meters per minute
Low Pressure Setting
High Pressure Setting
51 scfm
Maximum values with water as media under submerged inlet conditions at ambient temperature:
Maximum air consumption
Low Pressure Setting
High Pressure Setting
Maximum free-flow delivery
Low Pressure Setting
High Pressure Setting
Maximum pump speed
Low Pressure Setting
High Pressure Setting
59 scfm
95 scfm
1.7 cubic meters per minute
2.7 cubic meters per minute
50 gpm
46 gpm
189 lpm
174 lpm
280 cpm
225 cpm
Maximum suction lift (varies widely
based on ball/seat selection and
wear, operating speed, material
properties, and other variables)
Maximum size pumpable solids
16 ft dry,
29 ft wet
4.9 m dry
8.8 m wet
1/8 in
3.2 mm
Recommended cycle rate for continuous
93–140 cpm
(in Low or High pressure setting)
20 cpm
(in Low or High pressure setting)
3/4 npt(f)
use
Recommended cycle rate for circulation
systems
Air inlet size
Fluid inlet size
Fluid outlet size
Weight
1 in. npt(f) or 1 in. bspt
1 in. npt(f) or 1 in. bspt
48 lb (aluminum manifolds)
60 lb (SST manifolds)
21.8 kg (aluminum manifolds)
27.2 kg (SST manifolds)
20
334014A
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Power (measured per ISO-9614–2)
At 70 psi (0.48 MPa, 4.8 bar) and 50 cpm
Low Pressure Setting
78 dBa
91 dBa
High Pressure Setting
At 100 psi (0.7 MPa, 7.0 bar) and full flow
Low Pressure Setting
90 dBa
High Pressure Setting
102 dBa
Sound Pressure (tested 3.28 ft [1 m] from equipment)
At 70 psi (0.48 MPa, 4.8 bar) and 50 cpm
Low Pressure Setting
84 dBa
96 dBa
High Pressure Setting
At 100 psi (0.7 MPa, 7.0 bar) and full flow
Low Pressure Setting
84 dBa
96 dBa
High Pressure Setting
Wetted parts
aluminum plus the material(s) chosen for seat, ball,
and diaphragm options.
Non-wetted external parts
aluminum, coated carbon steel
Fluid Temperature Range
NOTICE
Temperature limits are based on mechanical stress only. Certain chemicals will further limit the fluid
operating temperature range. Stay within the temperature range of the most-restricted wetted component.
Operating at a fluid temperature that is too high or too low for the components of your pump may cause
equipment damage.
Fluid Temperature Range
Diaphragm/Ball Material
Santoprene® (SP)
Fahrenheit
Celsius
-40° to 180°F
-40° to 82°C
334014A
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Husky Pump Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its
name to be free from defects in material and workmanship on the date of sale to the original purchaser for
use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a
period of five years from the date of sale, repair or replace any part of the equipment determined by Graco
to be defective. This warranty applies only when the equipment is installed, operated and maintained in
accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction,
damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper
maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall
Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment
with structures, accessories, equipment or materials not supplied by Graco, or the improper design,
manufacture, installation, operation or maintenance of structures, accessories, equipment or materials
not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an
authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco
will repair or replace free of charge any defective parts. The equipment will be returned to the original
purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material
or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of
parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY
OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above.
The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages
for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall
be available. Any action for breach of warranty must be brought within six (6) years of the date of sale..
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH
ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY
GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.),
are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable
assistance in making any claim for breach of these warranties..
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from
Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other
goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or
otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents,
notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or
indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du
présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés,
donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures
concernées.
Graco Information
To place an order, contact your Graco Distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original Instructions. This manual contains English. MM 334014
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Download from Www.Somanuals.com. All Manuals Search And Download.
|