Repair
310643T
Displacement Pump
EN
3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure
Model 248204, Series A
Ultrar Max II and Ultimate Mx II 695 and 795
ASM Zip--Sprayt 2700 Plus, 3100 Plus
ASM AllPro Mach 8600 Plus and 11000 Plus
ASM H2700 Plus
Model 255968, Series A
ASM 3600G Plus
Model 248205, Series A
Ultra Max II and Ultimate Mx II 1095 and 1595
Model 249059, Series A
TexSprayt Mark V
Model 249057, Series A
TexSpray Mark V
Model 277069, Series A
LineLazert IV 3900, R300
Model 277070, Series A
LineLazert IV 5900
Model 253056, Series A
Mark IV
Model 257146, Series A
Ironman 300E and Ironman 500G
Important Safety instructions
Read all warnings and instructions in this manual.
Save these instructions.
8016A
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Pressure Relief Procedure
Tools Needed
WARNING
PRESSURIZED EQUIPMENT HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. To
reduce the risk of an injury from accidental spray
from the gun, splashing fluid, or moving parts,
follow the Pressure Relief Procedure whenever
you:
Vise
12 in. adjustable, open end wrench (2)
Hammer, 20 oz maximum
Small screwdriver
Throat Seal Liquid
Pick or long small screwdriver
D are instructed to relieve the pressure,
D stop spraying,
D check or service any of the system equipment,
D or install or clean the spray nozzle.
Cleaning and Inspecting Parts
1. Engage gun safety latch.
2. Turn ON/OFF switch to OFF.
3. Unplug power cord.
1. Clean and inspect parts. Pay particular attention to
the ball seats in the intake valve and piston, which
must have no nicks or wear, and to the inside of
the sleeve and the outside of the piston rod, which
must not be worn or scratched. Replace worn or
damaged parts.
4. Disengage gun safety latch. Hold metal part of gun
against grounded metal pail and trigger gun into
pail to relieve pressure.
WARNING
5. Engage gun safety latch.
COMPONENT RUPTURE HAZARD
Never use sharp or pointed tools to
remove sleeve or other components
6. Open any fluid drain valves in system. Leave drain
valve open until ready to dispense again.
which could result in pump rupture and
cause serious bodily injury. If the sleeve cannot be
removed easily, return the sleeve and cylinder to
your Graco distributor for removal.
Pump Repair Kits
Pump
Repair Kit
248212
287825
248213
248204, 255968
253056
248205, 249057, 249059,
257146
2. Remove and clean the sleeve when you are
repacking the pump.
310643
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 3. Disassemble intake valve. Clean and inspect.
O-ring (227) may require a pick for removal.
Repair When Pump Is Off The Sprayer
Disassembling the pump
Fig. 1. Remove packing nut (202) and throat adjust-
ment spacer (228).
202
228
227
7570e
Fig. 3
Fig. 4. Tap piston rod out of cylinder with a hammer or
flip over and tap piston rod out against a bench.
ti2332a
7568A
Fig. 1
Note: Sleeve may come out
of cylinder with piston rod.
Fig. 2. Unscrew intake valve from cylinder.
7571a
Fig. 4
Fig. 5. Remove piston rod from sleeve, or remove
sleeve from cylinder. Mark IV: Remove sleeve spacer
(230) from sleeve.
7569A
Fig. 2
7572A
Fig. 5
4
310643
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 8. Remove throat packings and glands from cylin-
der. Discard throat packings and glands.
WARNING
COMPONENT RUPTURE HAZARD
Do not clean or wipe the piston valve
threads. Cleaning the piston valve
threads could destroy the special sealing
patch and cause the piston valve to come loose
during operation, causing pump bursting and
possible serious bodily injury.
Not
used on
248204
253056
255968
Fig. 6. Unscrew piston valve from piston rod. Clean
and inspect parts. The piston has a special thread
locking/sealing patch. Do not remove the patch. The
patch allows four disassembly/assembly procedures
before it is necessary to apply Loctiter to the threads.
7573B
Fig. 8
Assembling the pump
Fig. 9. Soak all leather packings in SAE 30W oil for 1
hour minimum prior to assembly. Stack male gland
(204) on piston rod. Alternately stack UHMWPE (208)
and leather (218) packings (note orientation) on piston
rod. Install female gland (217). Install piston wiper
(216) (note orientation) and backup washer (229) on
piston valve (210). The special sealing patch on piston
valve threads is good for four repackings. Use Loctiter
on piston valve threads after four repackings.
7576A
Fig. 6
Not
used on
Fig. 7. Remove packings and glands from piston rod.
210
248204
253056
255968
Not
used on
248204
253056
255968
229
216
217
218 204 208
7574d
ti3940b
Fig. 9
Fig. 7
310643
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 10. Install ball (206) in piston rod. If Loctiter is ap-
plied to piston valve threads, ensure that none gets on
ball.
Fig. 12. Soak all leather packings in SAE 30W oil for 1
hour minimum prior to assembly. Place male gland
(204) in cylinder. Alternately stack UHMWPE (203) and
leather packings (223) (note orientation). Place female
gland (224) in top of cylinder. Seat packings.
206
Not
used on
224
248204
253056
255968
203
223
204
7575A
Fig. 10
Fig. 11. Tighten piston valve to piston rod as specified:
7573f
Fig. 12
Torque to 27 +/--3 ft-lb
(248204, 253056, 255968,
277069)
Fig. 13. Install seal (201) into packing nut (202). Install
throat adjustment spacer (228) onto packing nut.
Loosely install packing nut into cylinder.
Torque to 55 +/--3 ft-lb
(248205, 249057, 249059,
277070, 257146)
201
202
228
7576A
7581A
Fig. 11
Fig. 13
6
310643
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 14. Grease piston packings.
Fig. 16. Grease top inch or two of piston rod that will
go through the cylinder throat packings.
7579A
Fig. 16
Fig. 17. Grease o-rings (221) and place on sleeve.
Slide sleeve/piston rod assembly into bottom of cylind-
er. Replace o-ring (207) if desired.
ti7578c
Fig. 14
Note: O-ring (207) is not required for safe pump opera-
tion.
CAUTION
Do not slide piston assembly into top of sleeve as
this may damage piston packing.
Fig. 15. Slide piston assembly into bottom of sleeve.
207
221
7577A
Fig. 15
7582A
Fig. 17
310643
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 18. Mark IV: Install o-ring (231) on sleeve spacer
(230) and install sleeve spacer on sleeve.
ti7340a
230
231
Fig. 18
Fig. 19. Reassemble intake valve with new o-ring
(227), seat (212) and ball (214). Seat may be flipped
over and used on other side. Clean seat thoroughly.
7569A
Fig. 20
Fig. 21. Torque packing nut (202) down onto adjust-
ment spacer (228) 100 +/--10 in-lb.
214
212
227
Remove throat adjustment spacer (228) when pump
packings begin to leak after much use. Then tighten
packing nut down until leakage stops or lessens. This
allows approximately 100 gallons of additional opera-
tion before a repacking is required.
202
228
7570f
Fig. 19
Fig. 20. Install intake valve on cylinder. If a wrench is
used torque as follows:
67 +/--5 ft-lb (Model 248204, 253056, 255968,
277069)
80 +/--5 ft-lb (Model 248205, 249057, 249059,
277070, 257146 )
If a wrench is not used, be sure intake valve is bot-
tomed out against cylinder.
7568A
Fig. 21
8
310643
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 2. Push up retaining spring (26).
Repair When Pump Is On The Sprayer
WARNING
SKIN INJECTION HAZARD
To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the Pressure Relief
Procedure on page 3.
Fig. 1. Remove intake valve.
26
ti4258a
Fig. 2
Fig. 3. Push out pin (29).
29
26
ti4258a
ti4258a
Fig. 1
Fig. 3
Fig. 4. Disassemble intake valve. Clean and inspect.
O-ring (227) may require a pick for removal.
227
7570A
Fig. 4
310643
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 5. Remove piston rod and sleeve.
Fig. 8. Invert piston rod and insert into cylinder to force
out throat packings.
7746A
Fig. 5
Fig. 5. Invert piston rod and sleeve and pound on hard
surface until piston rod comes out of sleeve. Mark IV:
Remove sleeve spacer from sleeve.
ti7339a
ti4258a
Fig. 8
Fig. 9. Insert piston rod into cylinder with pin hole up
and piston valve down. Insert pin into piston rod and
crank shaft.
7572A
Fig. 6
Fig. 7. Remove packing nut (202)
202
ti4258a
Fig. 9
7726A
Fig. 7
10
310643
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 10. Remove piston valve from piston rod with a
wrench.
Fig. 12. Soak all leather packings in SAE 30W oil for 1
hour minimum prior to assembly. Stack male gland
(204). Alternately stack UHMWPE (203) and leather
(223) packings (note orientation). Install female gland
(224). Install seal (201) and packing nut (202) and
throat adjustment spacer (228).
Not
used on
248204
253056
255968
224
201
228
203
223
204
ti4258a
Fig. 10
202
Fig. 11. Remove pin and piston rod from cylinder.
7573c
Fig. 12
Fig. 13. Remove packings and glands from piston rod.
ti4258a
Not
Fig. 11
used on
248204
253056
255968
ti3939a
Fig. 13
310643
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 14. Soak all leather packings in SAE 30W oil for 1
Fig. 16. Grease piston packings.
hour minimum prior to assembly. Stack male gland
(219) on piston rod. Alternately stack UHMWPE (208)
and leather (218) packings (note orientation) on piston
rod. Install female gland (217). Install piston wiper
(216) and backup washer (229) (note orientation) on
piston valve (210). The special sealing patch on piston
valve threads is good for four repackings. Use Loctiter
on piston valve threads after four repackings.
ti7578c
Fig. 16
219
217
Not
CAUTION
Do not slide piston assembly into top of sleeve as
this may damage piston packing.
used on
248204
253056
255968
216
229
Fig. 17. Slide piston assembly into bottom of sleeve.
Assure V-packing and u-cup are not rolled over or
damaged. Mark IV: Install o-ring (231) on sleeve
spacer (230). Install sleeve spacer on sleeve.
206
210
218
208
ti3941a
Fig. 14
ti7341a
Fig. 10. Install ball (206) in piston rod. If Loctiter is ap-
plied to piston valve threads, ensure that none gets on
ball. Install piston valve on piston rod.
Torque as follows:
Mark IV
27 +/--3 ft-lb (Model 248204, 253056, 255968,
277069)
55 +/--3 ft-lb (Model 248205, 249057, 249059,
277070, 257146)
7577b
Fig. 17
Fig. 18. Grease top inch or two of piston rod that will
go through the cylinder throat packings.
206
7575A
Fig. 15
7579A
Fig. 18
12
310643
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 19. Grease o-ring (221) and place on sleeve. Slide
Fig. 21. Push up retaining spring (26) with screwdriver.
sleeve/piston rod assembly into bottom of cylinder. Re-
place o-ring (207) if desired.
Note: O-ring (207) is not required for safe pump opera-
tion.
207
221
26
ti4258a
ti4258a
Fig. 19
Fig. 21
Fig. 21. Torque seal and packing nut (202) down onto
throat adjustment spacer (228) to 100 +/--10 in-lb.
Fig. 22. Push in pin (29).
29
Remove throat adjustment spacer (228) when pump
packings begin to leak after much use. Then tighten
packing nut down until leakage stops or lessens. This
allows approximately 100 gallons of additional opera-
tion before a repacking is required.
202
228
26
ti4258a
Note: Make sure retaining ring falls into slot.
Fig. 22
7726b
Fig. 20
310643
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 23. Reassemble intake valve with new o-rings
Fig. 24. Install intake valve on cylinder. Torque:
70 +/--5 ft-lb (model 248204, 253056, 255968,
277069)
80 +/--5 ft-lb (Model 248205, 249057, 249059,
277070, 257146)
(227) and (230), seat (212) and ball (214). Seat may
be flipped over and used on other side. Clean seat
thoroughly.
214
212
227
230
7570f
Fig. 23
ti4258a
Fig. 24
14
310643
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
222
201
202
228
224
203
204
V-Maxt UHWMPE, blue
223
Leather
205
221
220
Pump 248204
206
207
219
2
208
217
216
218
Leather
V-Maxt UHWMPE, blue
210
229
221
215
214
213
7683d
212
227
230
Fig 25
Technical Data
Maximum working pressure . . . . . . . . . . . . . . . 3300 psi
(227 bar, 22.7 MPa)
Fluid inlet size . . . . . . . . . . . . . . . . . . . 1-5/16--12 un(m)
Fluid outlet size
248204, 255968, 277069 . . . . . . . . . . . . . . . . 1/4 npt(f)
248205, 249057, 249059, 253056,
277070, 257146 . . . . . . . . . . . . . . . . . . . . . . . 3/8 npt(f)
Wetted parts . . . . . . . . . . stainless steel, PTFE, leather,
nylon, zinc-plated carbon steel, tungsten carbide,
chrome plating, fluoroelastomer, acetal, polyethylene
310643
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts -- Pump 248204, 277069, 255968
Model 248204, Series A; 277069, Series A; 255968, Series A
Ref
No.
201
Part No. Description
Qty.
201
202
203* 192692
179810
193046
SEAL, throat
NUT, packing
1
1
3
202
228
221*
222
V-PACKING, throat,
V-Maxt UHMWPE, blue
GLAND, male, throat
CYLINDER, pump
Model 248204, 255968
Model 277069
BALL, sst, 0.3125 in.
PACKING, o-ring
V-PACKING, piston
V-Maxt UHMWPE, blue
VALVE, piston
204* 15C987
205
1
224*
243346
243346
1
1
1
1
3
206* 105444
207* 114054
208* 192693
*223
219*
218*
203*
204*
210
212† 239922
239932
1
1
KIT, seat, carbide
*208
includes 214 and 227
VALVE, intake (foot)
Model 248204, 255968
VALVE, intake, Model 277069
BALL, sst, 0.5000 in.
GUIDE, ball
213
15C785
195892
1
217*
216*
214*† 105445
215 192624
216* 118503
217* 178969
218* 178939
219* 196880
220
221* 108526
222 248206
223* 178940
224* 15C988
227*† 107079
1
1
1
1
2
1
1
2
1
2
229
WIPER, piston
206*
210
GLAND, female, piston
V-PACKING, leather, piston
GLAND, male
SLEEVE, cylinder
O-RING, PTFE
ROD, piston
V-PACKING, leather, throat
GLAND, female
248209
215
205
†*214
†*227
212†
213
PACKING, o-ring
1
1
1
207*
221*
228
192714
SPACER, throat, nut
WASHER, backup
O-RING, fluoroelastomer (not used
on Lo-boy)
229* 15C997
230* 118494
1
*
These parts are also included in Repair Kit 248212,
which may be purchased separately.
220
†
These parts are also included in Carbide Seat Kit
239922, which may be purchased separately.
(Not an O--ring groove)
230*
ti4255a
16
310643
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts -- Pumps 248205, 249057, 249059, 277070, 257146
Model 248205, Series A; 249057, Series A; 249059, Series A; 277070, Series A; 257146, Series A
Ref No.Part No.
Description
Qty.
231
232
117608
162485
NIPPLE, straight
1
1
Model 249057, 249059 (not shown)
ADAPTER, 3/8 npt x 3/8 npsm
Model 249057, 249059, 257146
(not shown)
201+ 183171
PLUG
NUT, packing
V-PACKING
1
1
4
202
193032
203*+ 193124
V-Maxt UHMWPE, blue
GLAND, packing, male, throat
CYLINDER, pump
Model 248205, 277070
Model 249057, 249059, 257146
BALL, 0.375 in.
*
These parts are also included in Repair Kit 248213, which
may be purchased separately.
204*+ 15C989
205
243347
196754
206
1
1
†
These parts are also included in Carbide Seat Kit 244199,
which may be purchased separately
+
These parts are included in Pump Repair Kit 249189.
101947*
Model 248205, 249057, 277070,
257146, sst
1
1
1
4
201
202
116327+
207*+ 156633
208*+ 193125
Model 249059, ceramic
PACKING, o-ring
V-PACKING, piston
V-Maxt UHMWPE, blue
VALVE, piston
228
221*
210
240150
1
212†
KIT, SEAT, carbide
includes 214 and 227
Model 248205, 249057, 277070,
257146
224*
222
244199
244571
*223
1
1
Model 249059
213
214
215
HOUSING, intake (foot)
Model 248205,
Model 249059, 249057
Model 277070, 257146
BALL
203*
15C783
196753
195894
1
1
1
219*
204*
*208
218*
102972*† Model 248205, 249057, 277070,
257146 sst, 0.875 in.
1
111453+
Model 249059, ceramic, 0.750 in.
GUIDE, ball
Model 249059, 249057
Model 248205, 277070, 257146
WIPER, piston
GLAND, female, piston
V-PACKING, leather, piston
GLAND, packing, male
SLEEVE, cylinder
Model 248205, 249057, 249059,
277070
Model 257146
PACKING, o-ring
ROD, piston
Model 248205, 277070
Model 249059, 249057, 257146
V-PACKING, leather, throat
GLAND, packing, female
PACKING, o-ring
1
1
1
1
1
1
3
1
1
217*
216*
196967
193027
229
206*
210
216*+ 118504
217*+ 183185
218*+ 15E329
219*+ 183178
220
205
215
248210
207*
†*214
†*227
257031
221*+ 107098
222
2
212†
213
221*
220
248207
249028
1
1
3
1
1
1
1
1
223*+ 183175
224*+ 15C990
227*†+ 108526
228+ C20987
229*+ 15C998
230*+ 118494
(Not an O--ring groove)
SPACER, nut
WASHER, backup
O-RING, fluoroelastomer
230*
(not used on 249057, 249059, 257146)
310643
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts -- Pump 253056
Ref
No.
Part No. Description
Qty.
201*§
202
201*§ 179810
202 193046
SEAL, throat
NUT, packing
1
1
221*§
228*§
224*§
203*§ 192692
V-PACKING, throat,
V-Maxt UHMWPE, blue
3
222
204*§ 15C987
GLAND, male, throat
CYLINDER, pump
BALL, sst, 0.3125 in. (optional)
1
1
1
205
287876
206* 105444
*§223
206§ 119259
BALL, ceramic, 0.3125 in.
(standard)
1
1
3
219*§
203*§
204*§
207*§ 156593
208*§ 192693
PACKING, o-ring
V-PACKING, piston
V-Maxt UHMWPE, blue
VALVE, piston
210
212†n 197470
213 287878
287877
1
218*§
217*§
SEAT, carbide
HOUSING, intake
BALL, sst, 0.875 in. (optional)
1
1
1
*§208
214*† 102972
216*§
229*§
214§n
111453 BALL, ceramic, 0.750 (stan-
dard)
215
1
196967
GUIDE, ball
1
1
1
2
206*§
210
216*§ 118503
217*§ 178969
218*§ 178939
219*§ 196880
WIPER, piston
GLAND, female, piston
V-PACKING, leather, piston
215
GLAND, male
SLEEVE, cylinder
1
1
220
221*§ 108526
222 249969
248209
205
†*§n214
†*§n227
O-RING, PTFE
ROD, pump (MARK IV)
2
1
207*§
223*§ 178940
V-PACKING, leather, throat
2
212†n
224*§ 15C988
227*† 108526
§n
GLAND, female
PACKING, o-ring
1
221*§
213
228*§ 158776
229*§ 15C997
SPACER, throat, nut
WASHER, backup
1
1
1
230
15G494 SPACER, sleeve
220
231*§ 107098
O-RING
1
(Not an O--ring groove)
*
These parts are also included in Repair Kit with
stainless steel ball, 287825, purchased separately.
ti7338a
230
§
These parts are also included in Repair Kit with
ceramic ball, 24V063, purchased separately.
231*§
†
These parts are also included in Carbide Seat Kit
with stainless steel ball, 244199, purchased sepa-
rately.
n
These parts are also included in Carbide Seat Kit
with ceramic ball, 2V071, purchased separately.
310643
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
310643
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from
defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended,
or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the
equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained
in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non--Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does notdisclose anydefect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD
BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches,
hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in mak-
ing any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
ADDITIONAL WARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty
Program”.
TO PLACE AN ORDER, contact your Graco distributor, or call 1--800--690--2894 to identify the nearest distributor.
All written and visual data contained in this document reflect the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original insttructions. This manual contains English. MM 310643
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES P.O. BOX 1441 MINNEAPOLIS, MN 55440--1441 USA
Copyright 2003, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
12/2003, Revised January 2014
20
310643
Download from Www.Somanuals.com. All Manuals Search And Download.
|