Instructions-Parts
®
3:1 Mini Fire-Ball
225 Oil Pump
309868D
ENG
For non-corrosive and non-abrasive oils and lubricants only. For professional use only.
Not for use in explosive atmospheres.
.
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
Model No. 246775, Series B, Universal
Model No. 248097, Series B, Variable Length
540 psi (3.7 MPa, 37 bar) Maximum Working Pressure
180 psi (1.24 MPa, 12.4 bar) Maximum Air Input Pressure
Contents
Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
WARNING
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
•
•
•
Keep clear of moving parts.
Do not operate equipment with protective guards or covers removed.
Pressurized equipment can start without warning. Before checking, moving, or servicing equip-
ment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
•
•
Read MSDS’s to know the specific hazards of the fluids you are using.
Store hazardous fluid in approved containers, and dispose of it according to applicable guide-
lines.
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help pre-
vent fire and explosion:
•
•
Use equipment only in well ventilated area.
Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic
drop cloths (potential static arc).
•
•
•
•
•
•
Keep work area free of debris, including solvent, rags and gasoline.
Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
Ground equipment and conductive objects. See Grounding instructions.
Use only grounded hoses.
Hold gun firmly to side of grounded pail when triggering into pail.
If there is static sparking or you feel a shock, stop operation immediately. Do not use equip-
ment until you identify and correct the problem.
309868D
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
a guide for selecting and installing a pump. It is not an
actual system design. Contact your Graco distributor for
assistance in designing a system to meet your needs.
.
F
E
A
C
L
D
J
H
N
M
B
G
K
P
Key
A
B
Bleed-type master air valve
Air line filter
H
J
Dispensing valve
Fluid hose
C
D
E
F
Air regulator and gauge
Air inlet
Ground wire
Pump
Drain valve
K
L
M
N
P
Thermal relief kit (235998)
Air line lubricator
Bung adapter
Fluid outlet
Extension tube
G
FIG. 1
4
309868D
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
•
Any pails used when flushing: Use only metal,
Mounting the Pump
grounded pails when flushing. Make firm
metal-to-metal contact between a metal part of the
dispensing valve and the pail. Use the lowest possi-
ble pressure.
Mount the pump securely so that it cannot move dur-
ing operation. Failure to do so could result in per-
sonal injury or equipment damage.
To maintain grounding continuity when flushing or reliev-
ing pressure, always hold a metal part of the valve firmly
to the side of a grounded metal pail, then trigger the
valve.
•
•
Select a location that allows the operator easy
access to the pump and air controls, sufficient room
to change supply containers, and a secure
mounting platform.
To ground the pump, remove the ground screw (Z) and
insert through the eye of the ring terminal at end of
ground wire, (Y). Fasten the ground screw back onto the
pump and tighten securely. Connect the other end of the
ground wire to a true earth ground. See FIG. 2. To order
a ground wire and clamp order Part No. 222011.
If you are mounting the pump directly on the supply
container, be sure it is positioned so the pump’s
intake tube is no more than 1 in. (25 mm) from the
bottom of the container. Mount the pump to the
cover or other suitable mounting device.
To prevent damage to the pump, remove sedi-
ment from the bottom of the container before
installing a pump in an existing container.
Y
Z
Grounding
Proper grounding is essential to maintaining a safe
system.
TI1052
FIG. 2
To reduce the risk of static sparking, ground the pump.
Check local electrical codes for detailed grounding
instructions for your area and equipment type. Be sure
the following equipment is properly grounded:
•
•
Air and fluid hoses: Use only electrically conductive
hoses.
•
•
Air compressor: Follow manufacturer’s
recommendations.
Dispensing valve: Obtain grounding through con-
nection to a properly grounded fluid hose and pump.
•
•
Fluid supply container: Follow your local code.
Object being lubricated: Follow your local code.
309868D
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation
See FIG. 1 to identify references shown in parentheses,
i.e., (A).
3. Open the pump air regulator (C) slowly, just until the
pump is running. When the pump is primed and all
air has been pushed out of the lines, close the dis-
pensing valve (H).
NOTE: When the pump is primed, and with sufficient air
supplied, the pump starts when the dispensing valve (H)
is opened, and shuts off when it is closed.
This equipment stays pressurized until pressure is
manually relieved. Read PRESSURIZED EQUIP-
MENT HAZARD warnings on page 2.
4. Adjust the air regulator (C) until you get sufficient
flow from dispensing valve (H). Always run the
pump at the lowest pressure necessary to get the
desired results. Do not exceed the maximum work-
ing pressure of any component in the system.
Maximum working pressure of all components in the
system may not be the same. To reduce risk of over-
pressurizing any component, be sure you know the
maximum working pressure of each component.
Never exceed the maximum working pressure of the
lowest rated component in the system. Overpressur-
izing any component can result in rupture, fire, explo-
sion, property damage, and serious injury.
CAUTION
Never allow the pump to run dry of the fluid being
pumped. A dry pump will quickly accelerate to a high
speed, possibly causing pump damage. It may also get
very hot.
To determine the fluid output pressure using the air
regulator reading, multiply the ratio of the pump by
the air pressure shown on the regulator gauge. For
example:
5. If your pump accelerates quickly or is running too
fast, stop it immediately and check the fluid supply. If
the supply container is empty and air has been
pumped into the lines, prime the pump and lines
with fluid, or flush it and leave it filled with a compat-
ible solvent. Be sure to eliminate all air from the fluid
lines.
3:1 ratio x 100 psi air = 300 psi fluid output
Limit the air pressure to the pump so that no air line
or fluid line component is overpressurized.
Pressure Relief Procedure
1. Close the pump air regulator (C) and the bleed-type
master air valve (A), required in your system.
6. Read and follow the instructions supplied with each
component in your system.
7. If the pump will be unattended for any period of
time, if there is an air supply interruption, or at the
end of the work shift, shut off the system and always
relieve the pressure.
2. Hold a metal part of the dispensing valve (H) firmly
to a grounded metal waste container, and trigger the
valve to relieve fluid pressure.
Starting and Adjusting the Pump
1. With the air regulator (C) closed, open the
bleed-type master air valve (A).
2. Open the dispensing valve (H) into a grounded
metal waste container, making firm metal-to-metal
contact between the container and valve.
6
309868D
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
Check all other possible problems and solutions
before disassembling the pump. Before you trouble-
shoot problems using the table below, relieve the
pressure and disconnect the pump fluid line. If the
pump starts when the air is turned on again, the
fluid line, dispensing valve, etc., is clogged.
Problem
Cause
Solution
Pump fails to operate
Inadequate air supply pressure or
restricted air lines
Increase air supply; clear
Closed or clogged dispensing valve
Clogged fluid lines, hoses, valve, etc.
Damaged air motor
Open; clear
Clear
Service air motor
Refill and reprime or flush
Service air motor
Exhausted fluid supply
Continuous air exhaust
Erratic pump operation
Worn or damaged air motor gasket,
packing, seal, etc.
Exhausted fluid supply
Refill and reprime or flush
Pump operates, but output low Held open or worn intake valve or pis- Clear; service
on down stroke ton packings
Pump operates, but output low Held open or worn piston ball or piston Clear; service
on up stroke packings
Pump operates, but output low Inadequate air supply pressure or
Increase air supply; clear
on both strokes
restricted air lines
Closed or clogged valves
Exhausted fluid supply
Open; clean
Refill and reprime or flush
Clogged fluid lines, hoses, valves, etc. Clear
309868D
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor and Throat Service
Air Motor and Throat Service
8. Pull up on the cylinder cap nut (39) to expose the
trip rod, grasp the trip rod with padded pliers (Part
No. 248198), and unscrew the cylinder cap nut from
the trip rod.
Before You Start
•
Be sure you have all necessary parts on hand.
Pump Repair Kit 246918 includes repair parts for
the pump and air motor. Use all the parts in the kit
for the best results. Parts included in the kit are
marked with one asterisk, for example (17*), in the
text and drawings. See Parts, page 14.
CAUTION
Do not damage the plated surface of the trip rod (40).
Damaging the surface of the trip rod can result in
erratic air motor operation. Use the special padded
pliers to grasp the rod.
•
Two accessory tools should be used: Padded
Pliers, 248198, are used to grip the trip rod without
damaging its surface. Gauge, 15E796, is used to
ensure the proper clearance between the poppets
and seat of the transfer valve.
9. Remove the six screws (9) holding the air motor
cylinder (35) to the air motor base (28), and care-
fully pull the cylinder straight up off of the
piston (34).
Disassembly
1. Flush the pump, and relieve the pressure.
CAUTION
To avoid damaging the cylinder wall, lift the cylinder
straight up off of the piston. Never tilt the cylinder
while you are removing it.
10. Pull the air motor piston/displacement rod assembly
(29, 34) clear of the air motor base (28) by pulling up
on the air motor piston.
To reduce the risk of serious injury whenever you are
instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 6.
11. Remove the o–rings (13*, 103*) and u–cup
packing (16*) from the air motor base (28). Use nee-
dle–nose pliers to remove the u–cup packing from
the bottom of the air motor base.
2. Disconnect the ground wire from the grounding
screw (28a), disconnect the hoses, remove the
pump from its mounting, and clamp the air motor
base in a vise horizontally by closing the vice jaws
on the flange.
39
3. Use a strap wrench on the fluid cylinder (105) to
screw it out of the air motor base (28). See Parts,
35
40
4. Pull the displacement rod (29) down as far as it will
5. Using wrenches on the flats of the displacement
rod (29) and on the flats of the fluid piston (107),
unscrew the fluid piston from the displacement rod.
Remove the ball (100) from the end of the displace-
ment rod, and remove the packing o–ring (102*)
from the fluid piston. See Parts, page 14.
18*
19
32*
34
28a
13*
9
16*
6. Clamp the air motor upright in the vice by closing
the vice jaws below the flange.
flange
7. Unscrew the cylinder cap nut (39) from the top of
the air motor cylinder (35).
28
29
05725B
FIG. 3
8
309868D
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor and Throat Service
12. Remove the o–ring (18*) from the air motor
piston (34).
Reassembly
1. Clamp the displacement rod (29) upright in the vice
by closing the vice jaws on the flats of the displace-
ment rod.
13. Clamp the displacement rod upright in the vice by
closing the vice jaws on the flats of the displace-
ment rod.
2. Pull the new exhaust valve poppets (31*) into the
valve actuator (27), and clip off the top parts of the
poppets (shown with dotted lines in the Cutaway
View in Fig. 4).
14. Use a screwdriver to push down on the trip rod
yoke (23) to snap the toggle assemblies (L) down.
15. Remove the lockwires (25*) from the adjusting
nuts (24*) of the transfer valves. Screw the top nuts
off. Screw the valve poppet (32*) stems out of the
grommets (17*) and bottom nuts (24*). Take the
valve poppets off of the stems, and squeeze them
firmly to check for cracks.
3. Install the new grommets (17*) in the actuator (27),
place the inlet valve poppets (32*) in the piston, and
thread the bottom valve nuts (24*) onto the stems of
the inlet valve poppets until there are a few threads
left before the threads run out.
If you thread the valve nuts too far down onto the
poppets, they will run off the threaded part of the
poppets.
16. Grip the toggle arms (38) with pliers. Compress the
springs (20) and swing the toggle assembly (L) up
and away from the piston lugs (M), and remove the
assembly. Check that the valve actuator (27) is sup-
ported by the spring clips (26), but slides easily into
them. See Fig. 4.
4. Grease heavily and place the trip rod (40) in the air
motor piston (34), place the actuator (27) in the
yoke (23), and place the well–greased actuator/yoke
assembly in the piston, with the trip rod going
through the center holes of the actuator and yoke
and the stems of the inlet valve poppets (32*) going
through the grommets (17*).
To reduce the risk of pinching or amputating your fin-
gers, always keep fingers clear of the toggle
assemblies (L).
5. Thread the top valve nuts (24*) onto the stems of
the inlet valve poppets (32*) until one thread of the
inlet valve poppets is exposed above the valve nuts.
17. Remove the trip rod yoke (23), actuator (27), and
trip rod (40). Check the exhaust valve poppets (31*)
for cracks.
6. Install the toggle pins (36) in the yoke (23), place the
toggle arm (38) ends of the toggle assembly (L)
onto the toggle pins, and snap the pivot pin (37)
ends of the toggle assembly into the piston lugs (M).
To remove the exhaust valve poppets (31*), stretch
them out and cut the end off with a sharp knife.
7. Measuring with the gauge (Part No.15E796), create
0.105 in. (2.7 mm) of clearance between the inlet
valve poppets (32*) and the piston seat when the
inlet valve is open. See the Cutaway View in Fig. 4.
Clean and Service
1. Clean all the parts carefully in a compatible solvent
and inspect for wear or damage. Use all the repair
kit parts during reassembly, and replace other parts
as necessary.
Adjust the distance between the inlet valve poppets
and the piston seat by turning the top valve
nuts (24*).
2. Check the polished surfaces of the air motor
piston (34), displacement rod (29), and cylinder
wall (35) for scratches or wear. A scored rod will
cause premature packing wear and leaking.
8. Tighten the bottom valve nuts (24*) by hand. The
grommets (17*) should be slightly compressed.
3. Lubricate all parts with a light weight, water-resis-
tant grease.
309868D
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor and Throat Service
2
L
20
37
38
40
23
3
40
25*
24*
26
27
31*
1
24*
17*
M
32*
17*
24*
18*
24*
34
26
0.105 in.
(2.7 mm)
32*
34
04118
04119
31*
Cutaway View
1
2
3
Turn wires up.
Push toggles (L) in and then up.
Cut off tops of poppets as indicated by dotted lines.
FIG. 4
13. Slide the displacement rod (29) down through the
packings, and lower the air motor piston (34) into
the air motor base (28).
CAUTION
Never re-use the old lock wires. They will get brittle
and break easily from too much bending.
14. Clamp the air motor upright in the vice by closing
the vice jaws below the flange.
9. Align the holes in the valve nuts (24*) and the slots
on the stems of the inlet valve poppets (32*). Drop
the lock wires (25*) through the holes in the valve
nuts and into the slots in the stems of the inlet valve
poppets. Pull the lock wires down tightly, and bend
the ends with pliers so that they cannot be pulled
back out of the holes.
15. Carefully lower the air motor cylinder (35) straight
down onto the piston assembly (34). Tighten the six
screws (9) holding the air motor cylinder to the air
motor base (28).
CAUTION
10. Take the assembly out of the vice so that you can
move it around for steps 11 and 12.
To avoid damaging the cylinder wall, lower the cylinder
straight down onto the piston. Never tilt the cylinder as
it is being lowered.
11. Grease and install the new o–rings (13*, 18*, 103*).
12. Install the new u–cup packing (16*) through the bot-
tom of the air motor base, with the lips facing toward
the bottom of the pump.
10
309868D
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor and Throat Service
16. Pull the trip rod (40) so it is sticking up out of the air
motor cylinder (35).
20. Clamp the flats of the fluid piston (107) in a vice,
and torque the displacement rod (29) to the piston
to 40 to 60 ft–lb (54 to 81 N•m).
You may have to hold the unit upside down to
shake the trip rod loose.
21. Clamp the air motor base (28) in a vise horizontally
by closing the vice jaws on the flange.
22. Use a strap wrench to screw the displacement
pump cylinder (105) to the air motor base (28), and
torque to 40 to 60 ft–lb (54 to 81 N•m).
17. Grip the trip rod (40) with padded pliers, screw the
cylinder cap nut (39) onto the trip rod, push the cyl-
inder cap nut down, and screw it into the top of the
cylinder.
23. Before remounting the pump, connect an air hose
and run the air motor slowly, starting with just
enough air pressure to make the air motor run, and
make sure that it operates smoothly.
CAUTION
Do not damage the plated surface of the trip rod (40).
Damaging the surface of the trip rod can result in
erratic air motor operation. Use the special padded
pliers to grasp the rod.
Never operate the pump with the warning plate (47)
or the identification plate (46) removed. These plates
protect your fingers from getting pinched or ampu-
tated by moving parts in the air motor.
18. Place the piston ball (100) in the displacement
rod (29).
19. Clean the threads of the fluid piston (107), apply
®
Loctite to the threads, install the new packing
o–ring (102*) on the fluid piston, and thread the fluid
piston onto the displacement rod (29).
24. Reconnect the ground wire before you resume regu-
lar pump operation.
309868D
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Displacement Pump Service
Displacement Pump Service
Be sure you have all necessary parts on hand. Pump
Repair Kit 246918 includes repair parts for the pump
and air motor. Use all of the parts in the kit for the best
results. Parts included in the kit are marked with one
asterisk, for example (13*), in the text and drawings. See
5. Using wrenches on the flats of the displacement
rod (29) and on the flats of the fluid piston (107),
unscrew the fluid piston from the displacement rod.
6. Take the piston ball (100) out of the displacement
rod (29), and take the packing o-ring (102*) off of
the fluid piston (107).
1. Flush the pump and relieve the pressure.
7. Clean and inspect the parts. Use all the repair kit
parts during reassembly, and replace other parts as
necessary.
8. Place the piston ball (100) in the displacement
rod (29).
To reduce the risk of serious injury whenever you are
instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 6.
9. Install the new packing o-ring (102*) on the fluid
piston (107).
2. Disconnect the hoses, remove the pump from its
mounting, and clamp the air motor base in a vise
horizontally by closing the vice jaws on the flange.
10. Clamp the flats of the fluid piston (107) in a vice and
torque the displacement rod (29) to the piston to
40 to 60 ft-lb (54 to 81 N•m).
3. Unscrew the intake valve housing (106) from the
fluid cylinder (105). Disassemble the intake valve
(see Parts, page 14). Clean and inspect the parts
for wear or damage, and replace parts as needed.
Be sure to check the o-ring (104*). Unless further
intake valve service is needed, reassemble and
reinstall, using liquid sealant on the male threads.
11. Clamp the air motor base (28) in a vise horizontally
by closing the vice jaws on the flange.
12. Use a strap wrench to screw the fluid cylinder (105)
to the air motor base (28), and torque to
40 to 60 ft-lb (54 to 81 N•m).
13. If you disconnected the ground wire, reconnect it
before you resume regular pump operation.
4. Use a strap wrench on the fluid cylinder (105) to
screw it out of the air motor base (28). Carefully
inspect the smooth inner surface of the cylinder for
scoring or irregular surfaces. Such damage causes
premature packing wear and leaking, so replace the
part if it is damaged.
12
309868D
Download from Www.Somanuals.com. All Manuals Search And Download.
Displacement Pump Service
309868D
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Parts
Air Motor
39
15
Pump
35
36
25*
13*
103*
105
24*
31*
19
46
37
20
38
9
17*
24*
27
23
100
107
40
10
102*
104*
32*
28a
26
108
101
18*
34
16*
1
7
47
28
30
106
29
TI4016b
1
Lips face down.
14
309868D
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model No. 246775, Series B, Universal
Model No. 248097, Series B, Variable Length
Air Motor
Pump
Ref.
Ref.
No. Part No. Description
Qty.
No. Part No. Description
Qty.
7
100078 SCREW, thread forming, hex head 12
100 100400 BALL, piston, metallic, 3/4 in.
101 100279 BALL, metallic, 7/8 in.
102* 107227 O-RING, buna-N
103* 107306 O-RING, fluoroelastomer
104* 157195 O-RING, buna-N
105 15C499 CYLINDER, fluid
106 15C500 HOUSING, valve, intake
107 15C501 PISTON, fluid
1
1
1
1
1
1
1
1
1
1
8-32 x 3/8 in.
9
101578 CAPSCREW, hex head,
6
8-32 x 3/8 in.
10
13*
15
16*
17*
18*
19
20
23
24*
25*
26
118718 SCREW, machine
113347 O-RING, buna-N
156698 O-RING, buna-N
118106 PACKING, u-cup
118107 GROMMET, lower valve
118108 PACKING, o-ring
118109 PACKING, square
118111 SPRING, compression, helical
15C245 YOKE, rod, trip
15C246 NUT, valve
15C247
15C248 CLIP, spring
15C249 ACTUATOR, valve
253580 BASE, motor, air (includes 28a)
2
1
1
1
2
1
1
1
1
4
2
2
1
1
1
1
1
2
2
1
1
2
2
2
1
1
1
1
108 15C533 RETAINER, ball
109 15C502 TUBE, extension, variable length,
Model 248097 only, (not shown)
110 222308 ADAPTER, bung, Model 248097
only, (not shown)
1
*Included in Pump Repair Kit 246918.
WIRE, lock
27
28
** Use gap adjustment tool 15E796 (also included in
Repair Kit 246918) to ensure correct gap setting for
poppets.
28a 116343 SCREW, grounding
29
30
31*
32*
34
35
36
37
38
39
40
46
47
15C252 ROD, displacement, mp
15C266 GASKET, copper
15C267 POPPET, valve, exhaust
248211 POPPET, valve, inlet**
15W205 PISTON, motor, air 2-1/4”
15C274 CYLINDER, motor, air
15C275 PIN, toggle
15C276 PIN, pivot
15C277 ARM, toggle
15C278 NUT, cap, cylinder
15C279 ROD, trip
246782 PLATE, muffler, serial number
246783 PLATE, muffler, warning
309868D
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Technical Data
(Data measured with 10 weight oil at 70°F (21°C)
Approx. air consumption and fluid flow @100 psi air and
3
80 cpm .....8.5 scfm @2.1 gpm (.241 m /min @7.9 lpm)
Fluid to air ratio.........................................................3:1
Dry suction lift (feet of water) ..................................... 23
Cycles/gallon (cycles/liter)............................ 43.5 (11.4)
Fluid flow @80 cpm (gpm/lpm)....................... 1.84 (7.0)
Pumping distance guideline.......... up to 250 ft. (76.2 m)
Maximum fluid pressure ........ 540 psi (3.7 MPa, 37 bar)
Air motor effective diameter.............. 2.25 in. (57.2 mm)
Wetted materials........... steel, polyurethane, aluminum,
buna-N, Rulon®
Air inlet port size .........................................3/8 in. npt(f)
Fluid inlet port size......................................1.5 in. npt(f)
Fluid outlet port size....................................1/2 in. npt(f)
Sound pressure (measured 1 meter from unit)..77.8 dB
Sound pressure (ISO 9614-2)............................85.6 dB
Air operating range............... 40-180 psi (0.28-1.2 MPa,
2.8-12 bar)
Performance Chart
Inlet Air Pressures:
psi
= 100 psi
(6.9 bar)
A
B
C
scfm
(m3 / min)
cycles/min
(bar)
43.5
87
174
130.5
= 70 psi
(4.8 bar)
500
(31.4)
40
(0.3)
= 40 psi
(2.8 bar)
400
(21)
32
(0.23)
300
(10.4)
24
(0.23)
A
200
(5.2)
16
(0.17)
B
C
100
(5.2)
C
B
8
(0.12)
A
0
0
gpm 0
(lpm)
2
1
4
3
(0.08)
Flow Rate
TEST FLUID: No 10 Weight Oil
16
309868D
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensional Drawings
Dimensional Drawings
Model 248097
Variable length
Overall Length: 59.2 in. (150.4 cm)
Model 246775
Universal
Overall Length: 18.9 in. (48 cm)
3/8 in. npt(f)
air inlet
3/8 in. npt(f)
air inlet
grounding
Grounding
screw
screw
1/2 in. npt(f)
fluid outlet
8.9 in.
(20 cm)
1/2in. npt(f)
fluid outlet
8.9 in.
(20 cm)
1-1/2 in. npt
40.68 in. (103.33
cm) drop tube is
cut to length
05750
Mounting Hole Layout
Pump Base
Order gasket 15R881 for sealed tank/drum mounting.
2.518 in.
(6.4 cm) dia.
4.250 in. (10.8 cm) bolt circle
0.266 in. (6.7 mm) diameter clearance holes
4.250 in. (10.8 cm) bolt circle
0.281 in. (7.1 mm) diameter clearance holes
309868D
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser. With the exception of any special, extended, or limited warranty published
by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 309868
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2004, Graco Inc. is registered to ISO 9001
Revised 03/2010
Download from Www.Somanuals.com. All Manuals Search And Download.
|
