Instructions-Parts
3A2573D
EN
Gun Splitter Valve
Use to operate one or two spray guns with one proportioner or premixed paint in a 1K
sprayer. Provides independent flushing of each gun while the other gun remains in use.
For professional use only.
262826 (includes carriage)
7250 psi (50 MPa, 500 bar) Maximum Material Working Pressure
5000 psi (35 MPa, 345 bar) Maximum Flush Inlet Working Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
c IIB T5
II 2 G
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
WARNING
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
•
•
Read MSDSs to know the specific hazards of the fluids you are using.
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious
chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious
injury, or property damage.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents.
• Many other fluids may contain chemicals that can react with aluminum. Contact your material
supplier for compatibility.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent serious injury, including
eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is
not limited to:
•
•
Protective eyewear, and hearing protection.
Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•
•
Do not operate the unit when fatigued or under the influence of drugs or alcohol.
Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
•
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS from distributor or retailer.
•
•
•
Do not leave the work area while equipment is energized or under pressure.
Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-
facturer’s replacement parts only.
•
Do not alter or modify equipment. Alterations or modifications may void agency approvals and cre-
ate safety hazards.
•
•
•
•
•
•
Make sure all equipment is rated and approved for the environment in which you are using it.
Use equipment only for its intended purpose. Call your distributor for information.
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
Do not kink or over bend hoses or use hoses to pull equipment.
Keep children and animals away from work area.
Comply with all applicable safety regulations.
3A2573D
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Identification
Component Identification
B
J
C/K
D
A
E
H
G
F
Key:
A
B
C
D
E
F
G
H
J
Gun #1 Material Shutoff Valve
Gun #1 Solvent Shutoff Valve
Solvent Inlet Port
Schematic View
D
Mixed Material Inlet Port
C
Gun #2 Solvent Shutoff Valve
Gun #2 Material Shutoff Valve
Gun #2 Outlet Port
Gun #1 Outlet Port
Optional Mixed Material Through Port For Third Gun
Solvent Check Valve
K
K
NOTE: The Optional Mixed Material Through Port (J)
can be used for a third gun.
B
E
A
J
F
G
H
4
3A2573D
Download from Www.Somanuals.com. All Manuals Search And Download.
Pressure Relief Procedure
Pressure Relief Procedure
Follow the Pressure Relief Procedure whenever
you see this symbol.
7. Disengage the trigger lock.
This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury from
pressurized fluid, such as skin injection, splashing
fluid and moving parts, follow the Pressure Relief
Procedure when you stop spraying and before
cleaning, checking, or servicing the equipment.
TI1950a
TI1953a
8. Hold a metal part of the gun firmly to a grounded
metal pail. Trigger the gun to relieve pressure.
9. Engage the trigger lock.
Relieve A and B Fluid Pressure
1. Engage the trigger lock.
10. If you are using a XP Sprayer, close the dual shutoff
handle (AE) and open the circulation handle (AC).
AC
AE
TI1949a
2. Close the main air shutoff valve (CA) on your pro-
portioner pump or 1K sprayer.
r_571101_3A0420A_9a-2
11. Always flush the mix hose after relieving A and B
fluid pressure through the mix manifold. See Flush
Mixed Material instructions in XP Sprayer manual.
CA
12. Shutoff the solvent supply pump and repeat steps
6-8 to relieve solvent pressure. Ensure solvent
valves (B, E) are open.
r_571100_3A0420A_11a-1
3. Shut off heaters, if used.
E - OPEN
B - OPEN
4. Shut off feed pumps, if used.
5. Open gun #1 and gun #2 material shutoff valves (A,
F).
A - OPEN
F - OPEN
If you are using a XP Sprayer and the mixed material
has already been flushed, but pressure remains on
the A and B pumps, pressure can be relieved back
to the hoppers.
a. Close the main air shutoff valve (CA).
b. Open the circulation handle (AC).
6. Remove the spray tip and clean.
3A2573D
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
Flushing
1. Connect the mixed material supply line from the pro-
portioner or 1K sprayer to the manifold material inlet
port (D).
The gun splitter valve can flush both guns at the same
time or flush one gun independently while the other gun
continues to spray. The equipment must be flushed if:
2. Connect a hose between each manifold gun mate-
rial outlet (G,H) and spray gun fluid inlet.
3. Connect a solvent supply hose from the solvent sup-
ply to the manifold solvent inlet port (C).
•
•
Any gun will not be used within the pot life of the
material.
Neither gun will be used within the pot life of the
material. The mixed feed line, splitter, and both guns
must be flushed.
Operation
NOTICE
Do not allow mixed material to reside in equipment
longer than the pot life of the material at fluid tem-
perature. Pot life is much shorter than dry time.
Heated material cures much faster than ambient
and may damage your equipment. Check your
material safety data sheet (MSDS).
To reduce the risk of skin injection, follow the
Pressure Relief Procedure in your proportioner or 1K
sprayer manual when you stop spraying and before
cleaning, checking, servicing, or transporting
equipment.
Depending on which gun you want to supply material to,
open the material shutoff valve for gun #1 (A), gun #2
(F), or both valves.
1. Close the material shutoff valves gun #1 (A) or gun
#2 (F) for the gun to be flushed.
2. Relieve material pressure in the gun to be flushed
by unlocking the trigger lock. Trigger the gun into a
grounded pail. Lock trigger lock.
A - OPEN
F - OPEN
Locked
Unlocked
To shut off material supply to a gun, close the material
shutoff valve (A or F).
3. Lock trigger lock. Remove spray tip.
A - CLOSE
F - CLOSE
Locked
TI1948A
4. Turn on solvent supply and set the pressure as
needed for flushing.
6
3A2573D
Download from Www.Somanuals.com. All Manuals Search And Download.
Flushing
5. Open the gun’s solvent flush valve for gun #1 (B) or
gun #2 (E).
E - OPEN
B - OPEN
6. Unlock trigger lock and trigger gun into a grounded
pail. Flush out mixed material until clean solvent dis-
penses. Lock trigger lock.
Locked
Unlocked
7. Shutoff solvent pump and close solvent valve for
gun #1 (B) or gun #2 (E).
E - CLOSE
B - CLOSE
8. Lock trigger lock.
Locked
9. Final Flush must be done from the proportioner’s
mix manifold or while flushing your pre-mix sprayer,
through the gun splitter to the gun. Follow Flushing
procedure in your proportioner or sprayer manual.
NOTE: It is good practice to flush through each individ-
ual flush line valve after flushing through the main inlet.
3A2573D
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Parts
262826, Gun Splitter Valve
23
14
3 4
19 (x5)
20
13
5
2
12
21
25
1
1
5 13
12
2
18
17
15
1
3 4
2
29
ti19051a
3
11
4
4
1
2
3
4
5
Apply PTFE thread sealant to fittings.
Apply lubricant to o-rings.
Apply thread locker to external threads.
When replacing the seat, torque the stem to the seat five times,
up to 80 in-lbs (9 N•m), to form sealing surface.
Prior to assembly, turn valves counter-clockwise to the fully
open position. Torque valve into body (11) to 50 +/- 5 ft-lbs (67.7
N•m).
Ref. Part
Description
Qty.
2
Ref. Part
Description
VALVE, splitter
(includes items 11-29)
Qty.
17
18
19
20
15R381
HANDLE, black
1
---
1
117623
100721
563210
2
5
1
NUT, cap, 3/8-16
PLUG, pipe, 1/4 npt
VALVE, check, 1/4 npt, 5000 psi
(35 MPa, 345 bar)
FITTING, nipple, short; 1/4 npt
PLUG, pipe; 3/8 npt
2
3
4
262816 CARRIAGE, remote valve
100214 WASHER, lock
558673 SCREW, shcs, 5/16-18 x 3/4 in. (19
mm)
1
3
3
21
23
25
29
156971
101754
159239
156849
1
1
2
2
11
262822
195136
195132
24M220
1
4
4
2
BODY, splitter, gun
O-RING, PTFE
SEAT, carbide
CARTRIDGE, valve, solvent;
see page 9
CARTRIDGE, valve, paint;
see page 9
12*
13*
14
FITTING, nipple, pipe, reducing
PIPE, nipple; 3/8 npt
*
Included in Valve Seal Repair Kit 24M213 (purchase
15
24M219
2
8
3A2573D
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
24M220, Solvent Valve
24M219, Material Valve
46
36
46
36
52
1
50
52
1
50
3
4
46
2
1 3
3
4
36
41
2
ti19126b
51
1
ti19127b
31
1
3
43
4
51
1
33
4
1
2
3
4
Install seal with assembly tools 15T630 and 16T066 from valve seal repair kit.
Prior to installing the shutoff valve, apply medium strength thread locker to threads and allow to cure.
Apply lubricant to seal, threads and o-ring.
Torque to 130 in-lbs (15 N•m).
Ref. Part
Description
Qty.
Ref. Part
Description
Qty.
31*
33*
13
12
36
15M529 SEAL, check valve
16M186 VALVE, shut off, splitter, gun
195132 SEAT, carbide
195136 O-RING, PTFE
24M212 CARTRIDGE, valve, solvent
1
1
1
1
1
41*
43*
13
12
46
15M529 SEAL, check valve
16M186 VALVE, shut off, splitter, gun
195132 SEAT, carbide
195136 O-RING, PTFE
24M211 CARTRIDGE, valve, paint
1
1
1
1
1
*
Included in Valve Seal Repair Kit 24M213 (purchase separately).
24M213, Valve Seal Repair Kit
Ref.
12
13
Part
195136
195132
Description
Qty.
1
O-RING, PTFE
SEAT, carbide
1
31, 41 15M529
33, 43 16M186
1
1
1
1
SEAL, check valve
VALVE, shut off, splitter, gun
PACKING, o-ring #2-116, PTFE
TOOL, seal assembly
TOOL, seal assembly
50
51
52
15Y627
15T630
16T066
1
3A2573D
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Technical Data
Gun Splitter Valve
US
Metric
Maximum fluid working pressure
Mixed paint
7250 psi
5000 psi
50 Mpa, 500 bar
35 MPa, 345 bar
Flush solvent
Paint wetted materials
Manifold and valve housings
Seats
Nickel plated steel
Carbide
Valve stems
17-4 and 440c stainless
PTFE, UHMWPE
Seals
Solvent flush wetted materials
Check valve and fittings
Ball
Zinc plated steel
Chrome alloy
Aluminum
Gasket
Connections
Mixed paint inlet
Flush solvent inlet
Gun 1 and Gun 2 outlets
Optional Gun 3 straight through outlet
Weight
1/2 in. npt(f) port with 3/8 npt(m) inlet
1/4 in. npt(m) nipple
3/8 npt nipples in 3/8 npt(f) ports
3/8 npt(f) plugged port
Gun splitter valve with carriage
Carriage Dimensions
Height
10.2 lbs
4.6 kg
8 in.
20.3 cm
15.87 cm
23.52 cm
Width
Length
6.25 in.
9.26 in.
10
3A2573D
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
3A2573D
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 3A2573
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2012, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revised October 2014
Download from Www.Somanuals.com. All Manuals Search And Download.
|