ge.com
Safety Instructions . . . . . . . . . . . . .2
System Overview . . . . . . . . . . . .3–5
Owner’s Manual and
Installation Instructions
GNSV70FBL
GNSV75FWW
Installation Instructions . . . . .5–15
Battery Installation . . . . . . . . . . . .13
Faucet Installation . . . . . . . . . . . . . .9
Feed Water Supply . . . . . . . . . . . .6–8
Filter Replacement . . . . . . . . . . . .14
Flush Procedure . . . . . . . . . . . . . .15
System Installation . . . . . . . . . .10, 11
System Startup . . . . . . . . . . . . . . . .14
Tubing Connection . . . . . . . . . . . .12
Troubleshooting Tips . . . . . . . . .16
Consumer Support
Consumer Support . . . . .Back Cover
Parts List/Catalog . . . . . . . . . . . . .17
Warranty . . . . . . . . . . . . . . . . . . . .18
GNSV70FBL and GNSV75FWW are Tested and Certified by
NSF International against NSF/ANSI Standard 42 for the
reduction of Chlorine: Taste and Odor and Particulate Class I
and Standard 53 for the reduction of Lead, Cyst, Turbidity,
Asbestos, Mercury, Lindane, Atrazine, Benzene and VOC.
184D1069P002 49-50197 01-06 JR
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications Guidelines.
The Water Filtration System Uses the Following Canisters
Models GNSV70FBL and GNSV75FWW
FQSVF Filter
(160 gallon capacity)
Filter—White canisters with green band
• Reduces dirt, rust and sediment
• Reduces Chlorine: Taste and Odor
• Reduces Lead
• Reduces filterable Cysts (such as cryptosporidium and giardia)
• Reduces Turbidity
• Reduces Asbestos
• Reduces Mercury
• Reduces Lindane
• Reduces Atrazine
• Reduces Benzene
• Reduces VOC
• 0.5–1 micron nominal particulate reduction
This system conforms to NSF/ANSI 42 and 53 for the specific performance claims as verified and sustained by test data. See
Performance Data Sheet for details.
Installation Overview
Locate the drinking water system on the cold water supply pipe, under the kitchen and/or bathroom sink, to filter the cold
drinking water.
Filtered Water Faucet
Sink
Manifold
Adapter
Hot
Cold
Water Supply Valve
Outlet
Inlet
Filter Canisters
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Data Sheet.
SmartWater Filtration System GNSV70FBL and GNSV75FWW
Using Filter FQSVF
I This System has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the
indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving
the system, as specified in NSF/ANSI 42 and 53.
I Actual performance may vary with local water conditions.
I Do not use with water that is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Standard No. 42: Aesthetic Effects
Effluent
% Reduction
USEPA
MCL
Influent
Challenge Concentration
Influent
Average
Min. Required
Reduction
Parameter
Average
Maximum
Average
Minimum
Chlorine
T & O
—
—
—
2.0 mg/L 10%
—
1.94 mg/L
—
<0.05 mg/L
—
<0.05 mg/L
—
97.41%
—
97.22%
—
>50%
—
Particulate**
≥ 10000 particles
4100000 #/mL
24400 #/mL
67000 #/mL
99.35%
97.84%
>85%
Standard No. 53: Health Effects
Turbidity
Cysts
1 NTU***
99.95% red.
99% red.
11 1 NTU***
Min. 50000L
107 and 108 fibers/L;
fibers >10 µm long
11.08 NTU
0.21 NTU
<1 #/L
0.38 NTU
2 #/L
98.04%
>99.99%
99.89%
96.20%
>99.99%
99.82%
0.5 NTU
>99.95%
>99%
141750 #/L
168 MF/L
Asbestos
0.99885891 MF/L
<1 MF/L
Lead,
0.015 mg/L
0.015 mg/L
0.002 mg/L
0.002 mg/L
0.15 mg/L 10%
0.15 mg/L 10%
0.006 mg/L 10%
0.006 mg/L 10%
0.147 mg/L
0.143 mg/L
<0.001 mg/L
<0.001 mg/L
<0.0002 mg/L
0.000333 mg/L
<0.001 mg/L
<0.001 mg/L
<0.0002 mg/L
0.0005 mg/L
99.32%
99.30%
96.68%
94.34%
99.29%
99.29%
96.49%
92.06%
0.010 mg/L
0.010 mg/L
0.002 mg/L
0.002 mg/L
pH 6.5
Lead,
pH 8.5
Mercury,
pH 6.5
0.006033333 mg/L
0.0058 mg/L
Mercury,
pH 8.5
Lindane
Benzene
Atrazine
0.0002 mg/L
0.001 mg/L
0.003 mg/L
0.002 mg/L 10%
0.015 mg/L 10%
0.009 mg/L 10%
0.002016667 mg/L <0.00002 mg/L
<0.00002 mg/L
0.000500 mg/L
0.002000 mg/L
99.00%
96.47%
74.82%
98.95%
96.43%
61.54%
0.0002 mg/L
0.005 mg/L
0.003 mg/L
0.01417 mg/L
0.00830 mg/L
0.000500 mg/L
0.002000 mg/L
VOC Reduction
Chloroform
0.080 mg/L
0.30 10%
0.31429 mg/L
0.00186429 mg/L
0.0055 mg/L
99.40%
98.28%
95%
*Tested using a flow rate of 0.60 gpm (2.27 l/min); pressure of 60 psig; pH of 7.5 0.5; temp. of 68° 5°F (20° 3°C)
**Measurement in particles/mL. Particles used were 0.5–1 microns.
***NTU—Nephelometric Turbidity Units
Operating Specifications
Capacity: certified for up to 160 gallons (605 l); up to six months
Pressure requirement: 35–120 psi (2.8–8.2 bar)
Temperature: 33–100°F (0.6–38°C)
Flow rate: 0.60 gpm (2.27 l/min)
Replacement Filter Canisters/Estimated Replacement Costs
FQSVF—Replacement filter canister $35–40
For replacement parts, call toll-free 800.626.2002 (U.S.), 800.663.6060 (Canada–English), 800.361.3869 (Canada–French)
State of California
Department of Health Services
Water Treatment Device
Certificate Number
04 - 1601
Date Issued: February 9, 2004
Trademark/Model Designation
GXSV65 F
Replacement Element(s)
FQSVF
FQSVF
FQSVF
FQSVF
GQSV65 F
GNSV70 FBL
GNSV75 FWW
Manufacturer: General Electric Company
IOWA RESIDENTS ONLY:
The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section
116830 of the Health and Safety Code for the following health related contaminants:
Microbiological Contaminants and Turbidity
Inorganic/Radiological Contaminants
Cysts
Turbidity
Asbestos
Lead
Mercury
Store or Seller’s Name
Organic Contaminants
Atrazine
Lindane
Benzene
VOCs
Alachlor
Atrazine
Benzene
Endrin
Simazine
Styrene
1,1,2,2-Tetrachloroethane
Tetrachloroethylene
Toluene
2,4,5-TP (Silvex)
Tribromoacetic Acid
1,2,4-Trichlorobenzene
1,1,1-Trichloroethane
1,1,2-Trichloroethane
Trichloroethylene
Trihalomethanes (THMs)
Bromodichloromethane
Bromoform
Ethylbenzene
EDB
Address
Haloacetonitriles (HAN)
Bromochloroacetonitrile
Dibromoacetonitrile
Dichloroacetonitrile
Trichloroacetonitrile
Haloketones (HK)
1,1-Dichloro-2-Propanone
1,1,1-Trichloro-2-Propanone
Heptachlor
Heptachlor Epoxide
Hexachlorobutadiene
Hexachlorocyclopentadiene
Lindane
Methoxychlor
Pentachlorophenol
Carbofuran
Carbon Tetrachloride
Chlorobenzene
Chloropicrin
2,4-D
DBCP
o-Dichlorobenzene
p-Dichlorobenzene
1,2-Dichloroethane
1,1-Dichloroethylene
cis-1,2-Dichloroethylene
trans-1,2-Dichloroethylene
1,2-Dichloropropane
cis-1,3-Dichloropropylene
Dinoseb
City
State
Zip
Telephone
Chloroform
Chlorodibromomethane
Xylenes
Seller’s signature
Customer’s signature
0.6 gpm
Rated Service Flow:
Rated Service Capacity:
160 gal
Do not use where water is microbiologically unsafe or with water of unknown quality, except that
systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Date
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Data Sheet.
Organic Chemicals Reduced by Chloroform Surrogate Testing
Avg.1
Max.
Contaminant
Influent (µg/L)2
Effluent (µg/L)2
Alachlor
50
100
81
1.03
3.03
1.03
1.03
1.84
1.03
0.24
1.74
0.023
1.03
1.03
4.85
1.03
0.53
1.03
1.03
1.03
0.24
0.594
1.03
0.023
Atrazine
Benzene
Carbofuran
190
78
Carbon Tetrachloride
Chlorobenzene
77
Chloropicrin
2,4-D
15
110
52
Dibromochloropropane (DBCP)
o-Dichlorobenzene
p-Dichlorobenzene
1,2-Dichloroethane
1,1-Dichloroethylene
cis-1,2-Dichloroethylene
trans-1,2-Dichloroethylene
1,2-Dichloropropane
cis-1,3-Dichloropropylene
Dinoseb
80
40
88
83
170
86
80
79
170
53
Endrin
Ethylbenzene
88
Ethylene Dibromide (EDB)
Haloacetonitriles (HAN):
Bromochloroacetonitrile
Dibromoacetonitrile
Dichloroacetonitrile
Trichloroacetonitrile
44
22
24
9.6
15
0.54
0.64
0.24
0.34
1 Influent challenge levels are average influent concentrations determined in surrogate qualification testing.
2 µg/L means Micrograms Per Liter.
3 Maximum product water level was not observed but was set at the detection limit of the analysis.
4 Maximum product level is set at a value determined in surrogate qualification testing.
5 Chemical reduction percent and maximum product water level calculated at chloroform 95% breakthrough point as determined in surrogate qualification testing.
6 The surrogate test results for heptachlor Epoxide demonstrated a 98% reduction. These data were used to calculate an upper occurrence concentration, which would produce a maximum product water level at the MCL.
Testing was performed under standard laboratory conditions; actual performance may vary.
NOTE: Substances reduced are not necessarily in your water. Filter must be maintained according to manufacturer’s instructions, including replacement of filter cartridges.
WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be
used on disinfected waters that contain filterable cysts.
Installation Instructions.
Important Installation Recommendations
WARNING:
Read entire manual. Failure to follow all guides and rules could cause personal injury or property damage.
ICheck with your local public works department for plumbing codes. You must follow their guides as you install the Water Filtration system.
Tools and Materials Required for Installation
• Phillips screwdriver
• Two (2) adjustable wrenches
• Electric drill and drill bit to drill 3/4″ hole (type as required) if mounting hole is needed for faucet
• 1/16″ drill bit (optional for pilot holes)
• Tape measure
• If your main water line is a rigid pipe, you will require a compression fitting and possibly other plumbing hardware to complete
the installation.
CAUTION:
To avoid damaging the sink, consult a qualified plumber or installer for drilling procedures. Special drill bits may
be needed for porcelain or stainless steel.
Contents Included with the Product
• Water filter system assembly, including mounting screw
• Feed water adapter and supply valve
• Faucet assembly with electronic base monitor and tubing
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions.
Feed Water Adapter and Supply Valve
A. PREFERRED INSTALLATION
(Utilizing existing kitchen sink water supply valve [A] and removable faucet tubing [B])
For 1/2-inch and 3/8-inch installations
1. Refer to Fig. 1 to complete assembly depending on supply valve size (A).
2. Turn off the COLD water supply valve (A).
3. Unscrew the existing faucet tubing line (B) from the supply valve (A), COLD side only. NOTE: For rigid pipe, see C. Optional Installation
on page 7.
For 3/8-inch Valve
For 1/2-inch Valve
(H) Ferrule
(I) Nut
(B) Faucet tubing
line (not included)
(B) Faucet tubing
line (not included)
(D) Coupling
(F) Inlet valve
(F) Inlet valve
(D) Coupling
(F) Inlet valve
Fig. 2
(C) Adapter
(G) Gasket
(C) Adapter
(G) Gasket
(A) Water supply
valve (not included)
Fig. 1
(A) Water supply
valve (not included)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions.
Feed Water Adapter and Supply Valve
4. Assemble adapter (C) and coupling (D) as shown in Fig. 1, per your configuration. Be sure the gaskets (G) are in place before final
assembly. Start installation by hand, then finish tightening with adjustable wrench. Be careful not to overtighten or cross thread as
damage to threads may occur.
Note Adapter (C) orientation:
1/2-inch Installation—Rounded end of adapter (C) connects to coupling (D), then to existing faucet tubing (B).
3/8-inch Installation—Rounded end of adapter (C) connects to supply valve (A).
5. Hand tighten assembled adapter (C) onto supply valve (A) for the proper size installation. Be sure the gaskets (G), as shown
in Fig. 1, are in place before final assembly. Finish tightening with adjustable wrench. Be careful not to overtighten or cross
thread as damage to threads may occur.
NOTE: If inlet valve needs to be removed to complete this step, refer to D. Removal and Reinstallation of Inlet Valve on page 8.
6. Reconnect faucet tubing line (B) to top of adapter (C).
7. Remove nut and ferrule from end of inlet valve. Using the 4 feet of tubing provided, place the nut (I) and ferrule (H) onto
the tubing and install onto inlet valve (F) as shown in Fig. 2. Tighten with adjustable wrench.
NOTE: Inspect the ends of the tubing to be sure there are no imperfections and end of tubing is cut square. It may be necessary to cut the tubing again.
B. OPTIONAL HOME INSTALLATION—SADDLE VALVE
(Where codes permit): Saddle valve must be able to connect with 1/4-inch tubing supplied with system.
Not supplied with product; check your local hardware or home service store for product.
For 1/2″ OD or larger metal tubing only.
NOTE: Codes in the state of Massachusetts require installation by a licensed plumber and do not permit the use of the saddle valve.
For installation, use plumbing code 248-CMR of the Commonwealth of Massachusetts.
1. Turn off the cold water supply and install saddle valve as required by product selection. (Be sure to follow manufacturers’
installation instructions.)
DANGER:
If hole is required to be drilled in pipe, to protect yourself from serious injury or fatal shock, use a battery
powered hand drill only to make the hole. DO NOT USE AN ELECTRIC DRILL.
Open only after complete system has been installed.
C. OPTIONAL INSTALLATION
(For installation with rigid pipe between supply valve and sink faucet)
Option 1
1. Remove pipe from supply valve and sink faucet.
2. Obtain flexible pipe sized to your plumbing.
3. Install flexible pipe to sink.
4. Go back to A. Preferred Installation section step 4.
Option 2
1. Obtain compression fittings to fit rigid pipe.
2. Obtain any other fittings required to connect compression fittings to adapter.
NOTE: Adapter has 1/2-inch and 3/8-inch internal and external threads.
3. Remove pipe from supply valve.
4. Cut pipe to fit length of assembled fittings and adapter.
5. Install compression fitting to pipe.
6. Go back to A. Preferred Installation section step 4.
NOTE: Above described materials are not included with the product.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions.
Feed Water Adapter and Supply Valve
D. REMOVAL AND RE-INSTALLATION OF INLET VALVE (This is only required if inlet valve needs to be removed to complete Step 5 on page 7.)
1. Remove inlet valve (F) from adapter (C) using adjustable wrench on valve body. See Fig. 3a for details. DO NOT USE WRENCH ON HEX
NUT END OF VALVE AS LEAK MAY OCCUR.
Fig. 3a
2. Remove all sealing tape from inlet valve (F) and adapter (C) threads.
3. Hand tighten assembled adapter (C) onto supply valve (A) for the proper size installation. Be sure the gaskets (G), as shown in Fig. 1,
are in place before final assembly. Finish tightening with adjustable wrench. Be careful not to overtighten or cross thread as damage
to threads may occur.
4. Using white thread sealing tape provided, apply approximately 9 wraps of tape around the large threads on inlet valve (F) in a
clockwise direction, as shown in Fig. 3b.
Fig. 3b
5 Hand tighten inlet valve (F) into the adapter (C), then finish tightening with adjustable wrench (see Fig. 3a). DO NOT USE WRENCH
ON HEX NUT END OF VALVE AS LEAK MAY OCCUR.
Faucet Spout Installations (see Fig. 4, page 9)
1. Remove spout (A) and faucet body (B) from faucet packaging.
2. Move the threaded dome-shaped collar (C) on the spout up and away from the o-rings on the spout.
3. Gently insert the spout into the top of the faucet body.
NOTE: Turning the spout left to right during installation will help the o-rings to slide in easily.
4. Once the spout (A) has been installed and fully seated, slide the threaded collar (C) down to the faucet body (B).
5. Tighten the collar by hand to the faucet body by turning in a clockwise direction.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions.
Faucet Installation
Be sure there is room underneath and above the sink to make the needed connections. Before starting, make sure there is sufficient
room for the battery powered faucet base. Select one of the following places to install the faucet:
1. In an existing sink spray attachment or soap dispenser hole.
2. In a hole to be drilled in the sink top.
3. In a hole to be drilled in the countertop, next to the sink.
NOTE: Be sure the faucet base will fit flat against the surface at the selected location so the bottom gasket between the base and surface area will seal.
Installation Steps (refer to Fig. 4 for clarification)
1. If drilling is needed, make a 3/4″ diameter hole.
Be sure to use the proper procedure for drilling porcelain or stainless steel. Special drill bits may be needed. Consult a qualified plumber
for the proper procedure.
2. Remove the faucet with pre-installed tubing, thin o-ring (D), faucet base (E), bottom base gasket (F), lock washer (G), hex nut (H)
and mounting bracket (I) from the packaging.
3. Feed tubing connected to the faucet through the thin o-ring (D), faucet base (E), bottom base gasket (F), lock washer (G) and
hex nut (H).
4. Thread the hex nut (H) up the stem of the faucet until the height between the bottom of the base gasket (F) and top of the lock
washer (G) is slightly larger than the thickness of the mounting surface (J).
5. Lower the faucet assembly into place in the mounting hole and orient to final position. Place the mounting bracket (I)
above the lock washer (G) around the faucet stem (Fig. 5). While holding the mounting bracket in place, securely tighten
the hex nut.
NOTE: Two people may be required to complete this step.
(A) Spout
(C) Collar
(B) Faucet body
(D) O-ring
(E) Faucet base
(G) Lock washer
(F) Gasket
(H) Hex nut
Fig. 5
(J) Mounting surface
(I) Mounting
bracket
Fig. 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions.
Mounting System Installation
Pick a location under the sink to mount the system. Location should be easily accessible, with clearance between the bottom of the filter
canisters and the floor or bottom of the cabinet; any less will result in difficulty of removing filter canisters (see Fig. 7). Allow enough
space on either side of the system for the tubing connections.
SCREW INSTALLATION
1. Remove this template from the manual for easier installation.
2. The top of the template openings should be placed a minimum of 17 inches above the bottom of the cabinet or floor where the
system is to be mounted (Fig. 6 and 7).
NOTE: Any distance lower may result in filter canisters interfering with the floor when removed.
3. Tape template to wall, then mark the wall where the screws are to be installed.
Install screws into the wall, leaving 3/16 inch clearance between the head of the screw and wall (drill pilot holes if needed) (Fig. 8).
5 inches
Template for screw hole pattern on back of filtration system
17 inches
Fig. 6
Bottom of Cabinet or Floor
5 inches
3/16 inch
Screws
Wall
17 inches
Screw
Fig. 8
Fig. 7
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions.
Mounting System Installation
Mounting System to Screws Installed in Wall
1. Remove shrink wrap from filter system.
2. Hang the system on the previously installed screws using the openings on the back of the unit (Fig. 9).
3. If the head of the screw will not slide into the upper slot, back out the screw by 1/4 turn and try again.
4. If the system is too loose when placed on the wall, tighten the screws by 1/4 turn and try again until a desired fit is achieved.
5 inches
Min.
17 inches
Fig. 9
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions.
Installing the Tubing
1. Measure 3/4″ from the end of each remaining piece of tubing (faucet end and inlet end) and mark with a pencil (Fig. 10). (Check
for roundness, smoothness, cuts, nicks, flat spots and sharp edges.)
3/4″
(19 mm)
Fig. 10
INCORRECT
2. NOTE: Water flow is from left to right. Water inlet is on the left side and water outlet is on the right side. Failure to follow will result in water
leaks when filter canisters are removed.
Outlet
to faucet
Inlet from supply valve
3 Push the tubing firmly into each fitting on the manifold until the line is flush with the fitting collar. (If the tubing is removed, re-cut
the end, measure, mark and re-insert). Tubing must be fully inserted to avoid leaks (Fig. 11). (To remove tubing, depress and hold white
collet; pull tubing out to remove.)
White Collet
(DO NOT REMOVE)
3
"
4
Insertion line
Insert tubing
Engagement
3/4″ (3/8″ tubing)
Fig. 11
4 Pull out slightly on tubing to ensure a good seal.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions.
Battery Installation
1. Use a small flat blade screwdriver or coin to remove the battery tray (A) at the side of the faucet base.
2. Install one CR2032, 3 volt battery (B) + side down into the battery tray (A) (Fig. 12).
3. Slide tray into faucet base (C) until the battery tray (A) edge is flush with the side of the base.
4. The blue light (D) will flash 5 times, indicating a proper installation and system reset.
5. Normally the light is off. After 6 months of use, the light will flash again every 30 seconds, indicating the proper time to replace the
filter canister.
NOTE: The blue light may stop blinking if it is allowed to blink for an extended period of time. To ensure proper operation, the battery should be replaced with
every filter change.
(D) Blue light
(B) Battery
–
(C) Faucet base
(A) Battery tray
+
Fig. 12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions.
System Startup Procedure
1. Slowly turn on cold water supply valve (A) in Fig. 1.
2. Turn on 1/4″ inlet valve to supply water to the system. (Valve is on when handle is pointing in same direction as water line coming
out of valve).
OFF
ON
3. Turn handle on faucet to allow trapped air to purge from the system.
NOTE: System may make noise during this procedure.
4. Check for water leaks around the system.
5. Once water starts to flow out of the faucet, allow the system to run for 5 minutes to flush out any harmless carbon fines that may
be present.
6. Turn off faucet and check around system for leaks.
Replacing the Filter Canisters
The blue light in the faucet base will flash every 30 seconds to indicate a filter change is needed. This occurs every 6 months.
1. Remove the filter canisters from the manifold by rotating the canisters to the left about 1/3 turn (Fig. 13). NOTE: A small amount
of water from the tubing between the filter and the faucet may come out. A small towel should be able to catch it.
2. Remove foil on top of new replacement filter canisters. Install the new canisters into the manifold by turning to the right about
1/3 turn until the alignment marks line up and the filter stops. DO NOT OVERTIGHTEN. The filter will rise up as it is turned.
3. Turn handle on faucet to allow trapped air to purge from the system.
NOTE: System may make noise during this procedure.
4. Check for water leaks around the system.
5. Once water starts to flow out of the faucet, allow the system to run for 5 minutes to flush out any harmless carbon fines that may
be present.
6. Turn off faucet and check around system for leaks.
7. Remove battery tray and replace battery to reset timer. (See Battery Installation for proper procedure).
Fig. 13
To remove
To install
Replacement Filter Canisters/Estimated Replacement Costs
FQSVF—Replacement filter canister $35–40
For replacement parts, call toll-free 800.626.2002 (U.S.), 800.663.6060 (Canada–English), 800.361.3869 (Canada–French).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions.
Flush Procedure
Whenever water of unknown quality is passed through the GE Water Filtration system, the filter canisters should be discarded and the
filtration system flushed.
WARNING:
These systems should only be used on microbiologically safe water.
Circumstances that may require flushing the system are:
• Boil water advisory
• Flooding of the GE Water Filtration system
• Long-term non-use
The procedure for flushing the GE Water Filtration system is:
1. See Replacing the Filter Canisters section and follow steps 1–4.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
Troubleshooting Tips
Save time and money! Review the chart below
first and you may not need to call for service.
Problem
Possible Causes
What To Do
Water contains tiny
black particles
New filter canisters contain
activated carbon, which is a
harmless black powder.
• Turn on the filtered water faucet and allow these harmless carbon
particles to purge from the canisters. Turn off the faucet when the
water is clear.
Water has air bubbles
and is cloudy
Air in system after installation.
• Will go away after water runs for a while.
Indicator light on the
faucet base is flashing
Six months usage has occurred.
This is the maximum life of
the filter canisters.
• Replace both filter canisters and battery in the faucet base.
Indicator light on the
faucet base is not blinking
Normal operation.
• Does not blink until 6 months of operation has passed.
Battery may need to be replaced. • Normally the light is not on. The light blinks every 30 seconds to
indicate a filter change is needed. This occurs about every 6 months.
• Replace battery. Indicator light will blink rapidly 5 times to indicate
proper installation and operation.
Indicator light on the
faucet base is not
working when new
battery is installed
Battery may need to be
replaced or it may have been
installed incorrectly.
• Observe orientation markings on the holder and install correctly.
Replace battery if it is old.
Chlorine taste and/or
odor in the product water
The filter canisters are no
longer removing chlorine
from the water supply.
•
Replace the filter canisters.
Water dispenses
very slowly
The filters have been installed
for too long.
• A six-month change-out period is recommended. Replace both
filter canisters.
The filter canisters have
become clogged.
• High sediment levels can cause premature clogging. Replace both
filter canisters.
Fittings are leaking
Tubing may not be installed
properly.
• Fully follow the installation instructions and be sure the tubing is
installed to the proper depth.
No water dispensing
from system
Shut off valve may be
turned off.
• Open the shut off valve.
Filter canisters not fully
installed.
• Fully follow the filter replacement instructions.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List.
GNSV70FBL, GNSV75FWW
To obtain replacement parts, call toll-free
800.626.2002 (U.S.), 800.663.6060 (Canada-English),
800.361.3869 (Canada-French)
General Electric parts catalog.
GNSV70FBL
GNSV75FWW
ITEM
GE CAT. NO.
WS19X10016
WS19X10015
WS22X10045
FQSVF
WS03X10046
WS15X10038
WS15X10039
WS10X10028
WS10X10029
WS02X10031
WS18X10009
WS07X10020
49-50197
DESCRIPTION
QTY
QTY
1
MANIFOLD ASSEMBLY
COVER, DUAL MANIFOLD
ELBOW & COLLET
1
1
2
1
1
1
–
1
–
1
1
1
1
1
1
2
1
1
–
1
–
1
1
1
1
1
2
3
4
FILTER SET (VOC)
5
O-RING KIT (2 LG, 4 SM)
FAUCET w/TUBING, CHROME
FAUCET w/TUBING, WHITE
FAUCET BASE, CHROME
FAUCET BASE, WHITE
WASHER & NUT—FAUCET
ADAPTER KIT—FEEDWATER
TUBING—6′0″
7
7
8
8
9
10
11
999
OWNER’S MANUAL & INST. INSTR.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
GE Water Filtration System Warranty.
All warranty service provided by our SmartWater™ Authorized Servicer
Network. To schedule service, on-line, 24 hours a day, visit us at ge.com,
or call 800.952.5039 in the U.S., or toll-free 866.777.7627 in Canada. Please
have serial number and model number available when calling for service.
Staple your receipt here.
Proof of the original purchase date
is needed to obtain service under
the warranty.
For The Period Of: GE Will Replace:
One Year
From the date of the
original purchase
Any part of the Water Filtration System (excluding filters) which fails due to a defect in materials
or workmanship. During this limited one-year warranty, GE will also provide, free of charge, all labor
and related service to replace the defective part.
What GE Will Not Cover:
I Service trips to your home to teach you how to use
the product.
I Filter cartridges and batteries after 30 days from date
of purchase.
I Improper installation, delivery or maintenance.
I Damage to the product caused by accident, fire, floods
or acts of God.
I Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
I Incidental or consequential damage caused by possible defects
with this appliance.
I Use of this product where water is microbiologically unsafe or
of unknown quality, without adequate disinfection before or
after the system. Systems certified for cyst reduction may be
used on disinfected water that may contain filterable cysts.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited
Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose,
are limited to one year or the shortest period allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the
USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip
charge or you may be required to bring the product to an Authorized GE Service location for service. In Alaska, the warranty excludes
the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your
local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Support.
GE Appliances Website
ge.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day of the year!
For greater convenience and faster service, you can now download Owner’s Manuals, order parts, catalogs, or even schedule
service on-line. You can also “Ask Our Team of Experts ” your questions, and so much more...
™
Schedule Service
ge.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at your convenience 24 hours
any day of the year! Or call 800.GE.CARES (800.432.2737) during normal business hours.
Real Life Design Studio
ge.com
GE supports the Universal Design concept—products, services and environments that can be used by people of all ages, sizes
and capabilities. We recognize the need to design for a wide range of physical and mental abilities and impairments. For details
of GE’s Universal Design applications, including kitchen design ideas for people with disabilities, check out our Website today.
For the hearing impaired, please call 800.TDD.GEAC (800.833.4322).
Extended Warranties
ge.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still in effect. You can
purchase it on-line anytime, or call 800.626.2224 during normal business hours. GE Consumer Home Services will still be there after
your warranty expires.
Parts and Accessories
ge.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA, MasterCard and
Discover cards are accepted). Order on-line today, 24 hours every day or by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be referred to qualified
service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
Contact Us
ge.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone
number, or write to:
General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance
ge.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for enhanced communication and
prompt service under the terms of your warranty, should the need arise. You may also mail in the preprinted registration card
included in the packing material.
Download from Www.Somanuals.com. All Manuals Search And Download.
|