GE Home Security System NX 108 116 124E User Manual

GE Security

NetworX Series

NX-108/116/124E LED keypad

User manual

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

INTRODUCTION

This manual is furnished to help you understand your security system and become proficient in its

operation. All users of your security system should read and follow the instructions in this booklet

and, if possible, practice on the keypad control while your professional installer is on site. Failure to

do so could result in the security system not working properly. Please keep this booklet in an

accessible location for the life of the security system. If you do not understand any part of this manual

you should notify your installing company.

The SECURITY CONTROL PANEL can be turned on (ARMED) and off (DISARMED) by entering a 4 or 6 digit

code into the keypad control, which is similar to a telephone keypad. If your security control panel has been so

programmed, you may be able to turn on (ARM) your system by simply pressing the [STAY] or [EXIT] key.

The system must always be disarmed using a 4 or 6 digit code.

The LED keypad includes up to 35 lights and a built-in electronic sounder. These provide specific information

relating to the status of the security system which is described in the booklet. Understanding what the lights

and sounds mean will help you to easily operate your system.

Keep in mind, the level of security you will obtain with this system relates specifically with two major

factors:

1. The quantity, quality and placement of security devices attached to this system.

2. The knowledge you have of the security system and how that knowledge is utilized in a weekly test of

the complete system.

You should be aware of the following facts when preparing a safety/security plan for your

home/business:

1. Your security system is an electronic device and is subject to failure or malfunction. Do not rely on it

as your single source of security.

2. Your system should be tested weekly.

3. Your system will not work without power.

4. Warning devices will need to be loud enough, wired correctly, and properly placed to provide

notification of an alarm event.

5. Smoke and heat detectors may not detect heat and smoke in all situations.

6. Use qualified security professionals to install and maintain your security system.

7. It may be possible to arm the security system without the backup battery connected. Your periodic

test should be done with AC Power removed to verify the battery is connected and adequately

charged.

8. Care should be taken to plug in and restrain the AC transformer after testing.

Please read the following information and instructions carefully before operating your security control

system.

NX-108/116/124E User manual

Page 3

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

GLOSSARY OF TERMS

Abort Delay

An option that allows a delay in reporting to the central station.

The level of access an individual has when using an alarm panel.

The location where alarm data is sent during an alarm report.

An option that allows the keypad to sound a ding-dong whenever an entry/exit

door is opened.

Authority Level

Central Station

Chime Feature

Codes

Can be either User Codes (relating to a person) or Function Codes (a toggle

switch to turn specific functions on/off). NOTE: A system may have either four-

digit codes or six-digit codes, but not a mixture of the two.

An option that allows a special code to be sent to the central station that

indicates the alarm system is being operated under duress.

An option that allows the system to be turned on (ARMED) with one or more

zones open. A system that is ready to be “force armed” will flash the ready

icon. (Note: Those zones that are not ready will not create an alarm.)

A Function Code is either a four (4) or six (6) digit code that has been

programmed by the installer to operate a device.

Duress Code

Forced Arming

Function Code

Group Bypass

Instant/Delay

An option that allows the user to bypass multiple zones with a single operation.

An option that allows an instant alarm condition for Entry/Exit doors, or grants a

delay to allow someone to enter/exit the building without an alarm, or before

entering a user code to disarm.

Master Code

Partitioned System

A master arm/disarm code that can program other user codes.

A system divided into multiple areas in which its own user or users control each

area.

Perimeter

Quick Arm

The outer edge of the protected area.

An option that allows you to turn on (ARM) the security system by pressing

either the [STAY] or [EXIT] key on the keypad control (for ARMING only) as

programmed by the installing company.

User Code

A four (4) or six (6) digit entry code used to arm or disarm the system.

NX-108/116/124E User manual

Page 4

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

KEYPAD DISPLAY & LED’S

Understanding the lights

Ready Light Power Light Service Light

Armed

Light

Instant Light

Fire Light

Numeric code

entry keys

Pull out zone ID Tab

Zone Lights

5 function keys

3 emergency activation keys

Armed Light

The armed light is “on” when the system is armed. The armed light is “off” when it is

disarmed. The armed light will flash when there has been an alarm during the previous arm

cycle.

Bypass Light The bypass light is “on” when any zone in this keypad’s partition is bypassed. If the bypass

light is “off”, no zones are bypassed.

Cancel Light

The cancel light will flash during an abort delay time. Entering a code followed by the

[CANCEL] key during or after an alarm report to the central station will cause the cancel

light to come on. It will stay on until the central station has received the cancel report.

NOTE: The cancel feature must be enabled. (See "Cancel/Abort Feature")

Chime Light

Exit Light

The chime light is “on” when the chime feature is “on”; “off” otherwise.

The exit light is “on” during the exit delay. Please note that the light will flash during the last

10 seconds of the exit delay as a warning that the time is running out. (The user may want

to disarm the system if the exit light is flashing in order to prevent an alarm. The user may

then re-arm the system and exit before the delay expires.)

Fire Light

A steady fire light means a fire zone has been faulted. A rapidly flashing fire light means that

a fire zone is in a trouble condition.

NX-108/116/124E User manual

Page 5

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

Power Light

Ready Light

The power light is on if the primary power is on. The power light will flash if the system has a

low battery condition.

The ready light is “on” when the system is ready to arm and “flashes” if ready to force arm.

The ready light is “off” when the system is not ready to arm because of a zone(s) being

faulted.

Stay Light

The stay light is illuminated when all interior zones are bypassed.

Service Light The service light will be “on” if the security system requires service. If the service light is “on,

press the [*] key followed by the [2] key to determine the service condition. One or more

zone lights will illuminate indicating what service(s) is required. Call your service provider

immediately for these problems. Below is a listing of what each digit means in a service

condition.

LIGHT

PROBLEM

SYSTEM FAULT - Press the [1] key. The zone light(s) that is

illuminated corresponds to the system fault(s) below:

Over Current Fault

Siren Trouble

Box Tamper

Expander Low Battery

Expander Box Tamper

Expander Trouble

Ground Fault

Expander Power

Note: Faults 1 & 2 are global in nature and will affect all

partitions of a multi-partition system. Press the [#] key to

return to the 1 of 8 service lights.

ZONE TAMPER - Press the [2] key and the zone light(s) will

illuminate showing the zone(s) that are tampered. Press the [#]

key to return to the 1 of 8 service lights.

ZONE LOW BATTERY - Press the [3] key. The zone light(s)

will illuminate showing which zone(s) has a low battery. This

only applies to wireless zones. Press the [#] key to return to the

1 of 8 service lights.

ZONE LOSS OF SUPERVISION - Press the [4] key and the

zone light(s) will illuminate showing which zone(s) has loss of

supervision. This only applies to wireless zones. Press [#] key

to return to the 1 of 8 service lights.

ZONE TROUBLE - Press the [5] key and the zone light(s) will

illuminate showing which zone(s) has a trouble condition.

Press the [#] key to return to the 1 of 8 service lights.

6 N TELEPHONE FAULT - Press the [6] key. The zone light(s) that

is illuminated corresponds to the system fault(s) below:

Line Trouble / Line Cut - This light will illuminate when

there is telephone line trouble or the telephone line has

been cut. The service light will remain lit until the

telephone trouble clears and a user code is entered.

Auxiliary Comm Device Fail - Radio backup has failed.

7 N FAILURE TO COMMUNICATE - This light will illuminate when

there is a failure to communicate between your system and the

central station.

8 N LOSS OF SYSTEM TIME - This light will illuminate when there

has been a loss of power and your system clock needs to be

reset.

EXIT

Press the [#] key to exit the Service Light mode.

N Note: This fault is global in nature and will affect all partitions

of a multi-partition system.

NX-108/116/124E User manual

Page 6

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

Zone Light

The zone lights are “off” when everything is normal. A zone light will be “on” if the zone has

been bypassed. If a zone light is “flashing”, that zone is in alarm or has been faulted. If a zone

light is “flashing” rapidly, it means that the zone is in a trouble condition. Trouble conditions

are

● Tamper ● Hardware ● Low Battery ● Loss of supervision

(A combination of Alarm/Fault and Tamper/Trouble will produce a rapid “flashing” light for a

short period of time, followed by a slow “flashing” light.)

EMERGENCY ACTIVATION KEYS

NOTES: You must hold these keys for 2 seconds to activate these functions. Your system may not be

programmed for these activation keys. You should press these keys only in an emergency situation that

requires response by emergency personnel. If your system is programmed for these functions, the following

reports can be sent.

Fire Key – This key can activate the fire alarm when pressed for two seconds. If your system is connected to

a monitoring center, an emergency report could be sent to that center.

Auxiliary Emergency Key – This key can activate the auxiliary alarm when pressed for two seconds. If your

system is connected to a monitoring center, an emergency report could be sent to that center.

Police (Panic/Hold-Up) Key - This key can sound a local audible alarm when pressed for two seconds. If

your system is connected to a monitoring center, an emergency report could be transmitted to that center.

NOTE: Some Panic/Hold-Up alarms are programmed to be silent at the protected site while reporting an

alarm to the monitoring center. Check with your installing company to determine how your security system will

respond to the Panic/Hold-Up activation.

NX-108/116/124E User manual

Page 7

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

KEYPAD FUNCTIONS

Arming your system in the “AWAY” mode

AWAY is used when the user is away from the premise and wants the interior protected. Listed below are the

steps to arm in the AWAY Mode:

Step 1 Close all protected doors and windows.

•

Ready light will be on or flashing when all protected zones and sensors are secure.

NOTE: If any zones are bypassed, a sensor in that zone can be violated without

affecting the ready light.

•

The security system will not arm if the ready light is not on or flashing.

If the power light is off, you have no AC power. Restore power if possible. If not, contact your

installing company for service.

•

If the power light is flashing, you have a battery failure. Contact your installing company for

service.

Step 2 Enter your 4 or 6 digit user code to arm the system.

•

The armed and exit lights will illuminate.

You may now leave the building.

IMPORTANT!

The exit light will flash rapidly for the last 10 seconds of the exit delay as a warning to the user that

the exit time is about to expire. The user may wish to disarm and rearm the system if more time is

needed.

Making the system ready to arm

If the ready light is not on or if it is flashing, a zone is not secure. To identify this zone check the zone lights.

A zone light will be “on” if the zone has been bypassed. If a zone light is “flashing”, that zone is in alarm or has

been faulted. If a zone light is “flashing” rapidly, it means that the zone is in a trouble condition.

Arming your system in the “STAY mode”

STAY is used when the user is inside the premise and wants protection around the perimeter. Listed below

are the steps to arm in the STAY Mode:

Step 1 Close all protected doors and windows.

•

Ready light must be on or flashing when all protected zones and sensors are secure.

NOTE: If any zones are bypassed, a sensor in that zone can be violated without

affecting the ready light.

•

The security system will not arm if the ready light is not on or flashing.

If the power light is off, you have no AC power. Restore power if possible. If not, contact your

installing company for service.

•

If the power light is flashing, you have a battery failure. Contact your installing company for

service.

Step 2 Enter your 4 or 6 digit user code. (Optional, if programmed.)

NX-108/116/124E User manual

Page 8

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

Step 3

•

Press the [STAY] key.

The bypass light will illuminate indicating that all interior zones are bypassed. (All interior

devices will bypass automatically, giving the user freedom of movement within the interior

area.)

•

For each interior zone bypassed, the corresponding zone light will also illuminate. If any

zone(s) have been bypassed previously by the user, the light(s) corresponding to the

bypassed zone(s) will illuminate, alerting the user that a zone(s) may be unprotected and

can be faulted without an alarm.

•

The stay light will also illuminate. Note: normally, all entry/exit doors will be delayed.

To change entry/exit to “Instant”, press the [STAY] key again.

The instant light will illuminate indicating that the entry/exit doors have no delay.

To change entry/exit to “Delayed”, press the [STAY] key again.

Step 4

The instant light extinguish indicating that the entry/exit doors are delayed.

Using the Quick Arm (optional)

The Quick Arm feature may be used if it is enabled. Quick Arm will allow the user to arm the security system

without entering a user code. Quick Arm in the AWAY mode is possbile by pressing the [EXIT] key. The

system can be quick armed in the STAY mode by pressing the [STAY] key. This feature is used for ARMING

ONLY, and will not disarm the security system. This is ideal for a maid or baby sitter code, etc.

Changing modes while system armed

Step 1 Pressing the [STAY] key will turn on/off (toggle) a delay on Entry/Exit doors and turn on/off

(toggle) the instant light.

Step 2 Press the [BYPASS] key at this time to turn on/off (toggle) all designated interior zones.

This is only possible if programmed by your installer (“bypass toggle” option set).

Step 3 When armed, pressing the [EXIT] key will start the Exit delay, enabling you to leave the building.

This is only possible if programmed by your installer (“re-exit” option set).

IMPORTANT!

The instant light needs to be off at this time if you plan on re-entering the building, otherwise you will create an

alarm. You may re-initiate an entry/exit delay by pressing the [STAY] key again. The instant light will go out.

Disarming the system

When you enter the protected area through one of the designated Entry/Exit doors, the keypad control

will sound a solid tone for the duration of the entry delay time, or until you enter a valid code. After

entering a valid code, the red armed light will go off and the tone will stop. The security system is now

DISARMED. If a valid code is not entered before the end of the entry delay, an alarm will occur.

(NOTE: If the red armed light is flashing during the entry delay, the alarm system has been

activated in your absence. Leave the building immediately and call your alarm company and/or

the police from a safe location.)

NX-108/116/124E User manual

Page 9

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

CANCEL / ABORT feature (optional)

The cancel light will flash during an abort delay time. If a code is entered followed by the [CANCEL] key while

this light is flashing, all abortable reports will stop the communication process. NOTE: The abort feature

must be enabled. Entering a code followed by the [CANCEL] key during or after an alarm report to the

central station will cause the cancel light to come on. It will stay on until the central station has received the

cancel report. NOTE: The cancel feature must be enabled.

Bypassing zones

If you wish to bypass one or more zones, this must be done while the system is in the disarmed state. The

following steps are used for bypassing zones:

Step 1 Press the [BYPASS] key.

Step 2 Enter user code, if required (optional). The bypass light flashes.

Step 3 Enter 1 or 2 digits indicating the zone you wish to bypass. (Example: Press the [1] key for zone 1,

press [1] - [2] for zone 12.)

Step 4 Press the [BYPASS] key again.

Step 5 The corresponding zone light will illuminate indicating the zone has been bypassed. Repeat steps 3

and 4 for any other zone(s) that need to be bypassed.

Step 6 Press the [BYPASS] key again -or- press the [#] key to exit the Bypass Mode. The bypass light will

stop flashing upon exiting the Bypass Mode.

Group bypass

By pressing the [BYPASS] key, followed by the [0] [0] key, then the [BYPASS] key again, all zones that are

designated as group bypass zones will be bypassed. Press the [BYPASS] key again to exit group bypassing.

Unbypassing

To manually unbypass zones, perform the bypassing procedure on a zone that is already bypassed. The

corresponding light for that zone will go off when unbypassed.

NOTE: All zones will automatically be unbypassed each time the system is disarmed.

Turning the door chime ON and OFF

The door chime feature must be enabled by your installer. The door chime is turned on or off by pressing the

[CHIME] key. If the chime is on, the chime light will be illuminated. If the chime is off, the chime light will be

off. Each press of the [CHIME] key will toggle the chime feature on/off and produce a momentary ding-dong

sound.

NX-108/116/124E User manual

Page 10

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

ADDING AND CHANGING USER CODES

Your system must be Disarmed to add/change user codes.

Step 1

Step 2

Press [r]-[5].

Enter a “Master Arm/Disarm Code”.

NOTE: For partitioned systems, someone changing the code of another person must

have access to all or more partitions than the user being changed.

Step 3

Step 4

The ready light will flash.

Enter the 2 digit (applies to NX4/6/8) or 3 digit (applies to NX8E) “user number” (always enter

2 digit such as [0] - [3] for user 3, or [1] - [0] - [0] for user 100).

Step 5

Step 6

Enter the new four (4) or six (6) digit “user code”.

NOTE: To delete a user code, enter [r]-[r]-[r]-[r] for a 4-digit code, or [r]-[r]-[r]-[r]-[r]-[r]

for a 6-digit code.

The ready light will flash indicating you are back at Step 4 above. If the code is rejected, the

sounder will beep 3 times.

Step 7

Step 8

If another “user code” needs to be programmed, return to Step 5.

Press the [#] key while the ready light is flashing to exit the User Code Programming Mode.

NX-108/116/124E User manual

Page 11

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

ASSIGNING USER CODE AUTHORITY LEVELS

Assign authority levels to users by following the steps below. Assign user codes before assigning authority

levels. Your system must be in the disarmed state to change user code authority levels.

Step 1

Step 2

Press [r]-[6].

Enter a “Master Arm/Disarm Code”.

NOTE: Someone changing the authority of another person can only add or remove

partition authorization for partitions to which they have access.

Step 3

Step 4

The ready light will flash.

Enter the 2-digit (applies to NX4/6/8) or 3-digit (applies to NX8E) user number. Always use

leading zeros when necessary, i.e. "004" for user number 4.

Step 5

Lights illuminated indicate the authority levels assigned to this code. An explanation of the

lights is listed below. You may toggle (turn on/off) the authority level by pressing the number

for that authority level.

LIGHT

AUTHORITY LEVELS IF LIGHT 8 IS OFF

Reserved (Note: Do not change if on.)

Arm Only

Arm Only After Close Window

Master Arm/Disarm (can program other codes)

Arm/Disarm

Bypass Zones

Open / Close Reporting

If this light is on, this code is programmed as a

function code. Do not change, Press [#] - [#] to exit.

Step 6

Step 7

Press the [r] key. The ready light will flash. This moves you to the partition enable. (The user

has access in partitions that are illuminated.)

The illuminated numbers indicate each partition where the user has access. To change any

of the partitions where the user has access, press numbers corresponding to areas where

you want to give the user access or deny access. (Example: If zone light #2 is lit, then the

user is assigned access to partition #2. By pressing the [2] key, the light will go off, denying

access to partition #2. Refer to chart shown below.

LIGHT

PARTITIONS ASSIGNED

Partition 1

Partition 2

Partition 3

Partition 4

Partition 5

Partition 6

Partition 7

Partition 8

Step 8

Step 9

When the partitions are assigned, press the [r] key. This returns you to Step 3 previously

mentioned. At this point you may enter another user number to assign authority level.

Repeat Steps 4 - 8 until you have assigned authority levels to all user numbers.

Press the [#] key to exit the Assigning Authority Level Program.

NX-108/116/124E User manual

Page 12

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

OTHER KEYPAD FUNCTIONS

Setting the keypad tone

Step 1

Step 2

Step 3

Press the [r] key.

Press the [0] key. Keypad is now in the “Adjust Tone” mode.

Pressing the [1] key will make the keypad sounder go to higher tones, pressing the [2] key will

make the keypad sounder go to lower tones.

Step 4

When the desired tone is reached, press the [#] key to set this tone and exit

from the “Adjust Tone” mode.

Change partition (optional)

Step 1

Step 2

Step 3

Step 4

Step 5

Press the [r] key.

Press the [1] key.

Press a NUMBER key between 1 and 8 to change partitions momentarily.

If no other key is pressed, it will go back to its standard partition in ten seconds.

If another key is pressed, the system will remain in the new partition until no keys have been

pressed for 60 seconds.

View alarm memory

Step 1

Step 2

Step 3

Press the [r] key.

Press the [3] key to display the zone(s) on the keypad that created the last alarm.

The ALARM MEMORY feature will flash those zones that created alarms and will light steady

those zones that were bypassed during the last alarm.

Test function (optional)

If programmed, this function will perform a battery test, communicator test, and/or a siren test.

Step 1

Step 2

Press [r] [4] [4]. The test will be performed as programmed.

If the siren test is performed, enter a user code to silence the siren.

No alarms will be sent and no reports will be sent unless a communicator test is performed, at which

time a test signal will be sent.

NX-108/116/124E User manual

Page 13

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

Detector reset function

This function is used to reset Smoke Detectors and Zone Troubles. Your system must be Disarmed to use

the Reset function.

Step 1

Step 2

Press [r]-[7]. Resets have now been performed. The FIRE light will go off if the smoke

detectors have been reset.

If the keypad begins beeping, the reset did not execute properly. Enter your code to silence

the keypad. Wait a few minutes and repeat step 2 to attempt another reset. If the keypad still

beeps after repeated attempts, please contact your installer.

Setting the system clock

Step 1

Step 2

Step 3

Enter [r][9][7].

Enter [master code].

Enter the “hour code” which must be two (2) digits.

Note: The clock is a 24-hour clock. Refer to the following table.

Time

Hour Code

Time

Hour Code

Time

Hour Code

12:00 Midnight

8:00 AM

4:00 PM

1:00 AM

2:00 AM

3:00 AM

4:00 AM

9:00 AM

10:00 AM

11:00 AM

12:00 Noon

5:00 PM

6:00 PM

7:00 PM

8:00 PM

5:00 AM

6:00 AM

7:00 AM

1:00 PM

2:00 PM

3:00 PM

9:00 PM

10:00 PM

11:00 PM

Step 4

Enter the “minutes code” which must be two (2) digits.

Example: 7 minutes after would be entered [0] – [7].

NX-108/116/124E User manual

Page 14

Download from Www.Somanuals.com. All Manuals Search And Download.

04/10/04

GE Security

Setting the system date

Step 1

Enter [r] [9][6].

Step 2

Step 3

Enter [master code].

Enter the “Day of Week “

1 = Sunday

3 = Tuesday

4 = Wednesday

5 = Thursday 7 = Saturday

6 = Friday

2 = Monday

Step 4

Enter the “Month Code”. Must always be two (2) digits.

01 = January

05 = May

09 = September

10 = October

02 = February 06 = June

03 = March

04 = April

07 = July

08 = August

11 = November

12 = December

Step 5

Step 6

Enter the “Day Code”. Must always be two (2) digits.

Example: The 5^thwould be entered as [0] – [5].

Enter the last two digits of the “Year Code”.

Example: For 2003 enter [0] – [3].

KEYPAD CONTROL TONES (BEEPS)

A sounder is built into the keypad. If programmed, your system keypad may sound for any of the following

reasons:

•

Beeps for all keypresses.

Sounds a continuous tone during the Entry delay time.

Pulses when a day zone is violated while the system is disarmed.

Pulses when a FIRE zone has a trouble condition.

Beeps 3 times for trying to arm with the “Ready” light off, if “Force Arming” has not been selected.

Beeps for 1 second or emits a “ding-dong” sound for the “Chime” feature.

Beeps during an exit delay; beeps rapidly for the last 10 seconds of an exit delay; and beeps 1

second at the end of the exit delay.

•

Pulses when the armed status changes and the AC power is off.

Pulses when the armed status changes and any zone(s) are bypassed.

Pulses when the armed status changes and a low battery is detected.

Pulses when the armed status changes and a Tamper condition is detected.

Beeps to indicate Telephone Line Cut, if selected.

Pulses when one or more of the following conditions are detected: Zone or Box Tamper, Low Battery,

AC Power Fail, or Expander trouble.

•

Beeps 3 times every minute indicating a low battery or missing transmitter is detected (if wireless

device is in system). Entering code will suppress the sounder for 12 hours.

Entering a valid code will silence the keypad sounder when it is pulsing. The arm/disarm state of your system

will not change when entering a code to silence a pulsing keypad sounder. Please contact your installer if a

trouble condition exists.

NX-108/116/124E User manual

Page 15

04/10/04

Download from Www.Somanuals.com. All Manuals Search And Download.

GE Security

APPENDIX A – REFERENCE TABLES

IMPORTANT

These reference tables on the following pages

need to be completed by your installer.

Keep these tables in a safe place!

Installing/Service Company

Address

: ______________________________

______________________________

: ______________________________

Telephone number

Name central station

Telephone number central station

Function codes programmed

Function code Controls function (action)

Entry/exit delay times in seconds :

Exit delay time:

Entry delay time:

Secondary Exit delay time:

Secondary Entry delay time:

This system counts ______ zones

Programmed functions:

ꢀAbort delay

ꢀForced arming

ꢀBattery test

ꢀCancel alarm

ꢀGroup bypass

ꢀQuick arm

ꢀChange partitions (LED)

ꢀChime

ꢀCommunicator test

ꢀManual fire alarm

ꢀManual medical alarm

ꢀManual panic alarm

ꢀRe Exit

ꢀService Light/Message enabled

ꢀSiren test

NX-108/116/124E User manual

Page 16

Download from Www.Somanuals.com. All Manuals Search And Download.

04/10/04

GE Security

Zone descriptions

Zone 1

Zone 2

Zone 3

Zone 4

Zone 5

Zone 6

Zone 7

Zone 8

Zone 9

Zone 10

Zone 11

Zone 12

Zone 13

Zone 14

Zone 15

Zone 16

Zone 17

Zone 18

Zone 19

Zone 20

Zone 21

Zone 22

Zone 23

Zone 24

NX-108/116/124E User manual

Page 17

Download from Www.Somanuals.com. All Manuals Search And Download.

04/10/04

www.gesecurity.com

EMEA Distribution is a division of GE Security EMEA bvba

manual for internal use only. GE Security EMEA bvba reserves the right to change information without

notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

Eiki Projector LC SVGA870U User Manual
Electro Voice Portable Speaker DML 1122A Series User Manual
Extron electronic Musical Instrument Amplifier HDMI DA2 User Manual
Extron electronic Switch FOX T USW 103 User Manual
Fellowes Paper Shredder CC4 User Manual
Fostex Speaker G9962ZX User Manual
Fundex Games Board Games Squeezed Out User Manual
GE Caller ID Box 2 9079 User Manual
GE Cell Phone NX 7002 User Manual
Gemini Stereo Amplifier PA 7000 User Manual