Frigidaire Microwave Oven 316137234 User Manual

INSTALLATION INSTRUCTIONS  
Over The Range Microwave Oven  
BEFORE YOU BEGIN  
Read these instructions completely and carefully.  
IMPORTANT  
inspector’s use.  
Save these instructions for local  
Proper installation is the responsibility of the installer.  
Product failure due to improper installation is not covered  
under the Warranty.  
IMPORTANT  
coordinates.  
Observe all governing codes and  
Please read all instructions thoroughly before installing  
the Over the Range Microwave Oven. Two people are  
recommended to install this product.  
NOTE TO INSTALLER – Be sure to leave these  
instructions with the Consumer.  
If a new electrical outlet is required, its installation should be  
completed by a qualied electrician before the Microwave  
Oven is installed. See 3 ELECTRICAL GROUNDING  
INSTRUCTIONS on page 2.  
NOTE TO CONSUMER – Keep these instructions for  
future reference.  
SKILL LEVEL – Installation of this appliance requires  
basic mechanical and electrical skills.  
2 WALL CONSTRUCTION  
1 MOUNTING SPACE  
This Microwave Oven/Hood should be mounted against and  
supported by a at vertical wall. The wall must be at for  
proper installation. If the wall is not at, use spacers to ll in  
the gaps. Wall construction should be a minimum of 2" x 4"  
wood studding and ³⁄₈" or more thick dry wall or plaster/lath.  
The mounting surfaces must be capable of supporting weight  
of 110 pounds—the oven and contents—AND the weight of  
all items which would normally be stored in the top cabinet  
above the unit.  
This Microwave Oven/Hood requires a mounting space on  
a wall as shown in Figure 1. It is designed to be used with  
standard 12" wall cabinets.  
12"  
30"  
15.5"  
The unit should be attached to a minimum of one 2" x 4"  
wall stud or two 2" x 3" wall studs.  
30" or more  
from cooking  
surface  
At least 2"  
Backsplash  
To nd the location of the studs, one of the following methods  
may be used:  
A. Use a stud finder, a magnetic device which locates the  
nails in the stud.  
B. Use a hammer to tap lightly across the mounting surface  
to find a solid sound. This will indicate stud location.  
The center of the stud can be located by probing the wall with  
a small nail to nd the edges of the stud and then placing a  
mark halfway between the edges. The center of any adjacent  
studs will normally be 16" or 24" to either side of this mark.  
66" or more  
from floor  
NEED HELP?  
For customers in the United States, call: 1-800-944-9044  
Figure 1  
For customers in Canada, call: 1-800-213-9397 (English)  
1-800-668-4606 ext.8199 (French)  
READ CAREFULLY. KEEP THESE INSTRUCTIONS.  
P/N 316137234  
TINSEB151WRRZ  
Printed in Thailand  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
5 TOOLS RECOMMENDED FOR  
INSTALLATION  
7 PREPARATION OF THE OVEN  
1. Open the bottom of the carton, bend the carton flaps back  
andtilttheovenovertorestonplasticfoampad. Liftcarton  
off oven and remove all packing materials, Installation  
Instructions, Wall Template, Top Template, Charcoal  
Filter, Turntable and Turntable Support; however, DO  
NOT REMOVE THE WAVEGUIDE COVER, which is  
located on the ceiling in the oven cavity. SAVE THE  
CARTON AS IT MAY MAKE INSTALLATION EASIER.  
Phillips Screwdriver  
Electric Drill  
¹⁄₂", ⁵⁄₈" and ³⁄₃₂" Drill Bits  
1 ¹⁄₂" Wood Bit or Metal Hole Cutter  
(if metal cabinet is used)  
Saw to cut exhaust opening (if needed)  
2. CHECK THE OVEN.  
Protective Drop Cloth for product and range -  
you may also use carton for protection  
Check the oven for any damage, such as misaligned or  
bent door, damaged door seals and sealing surfaces,  
broken or loose door hinges and latches and dents inside  
the cavity or on the door. If there is any damage, do not  
operate the oven and contact your dealer or Electrolux  
AUTHORIZED SERVICER.  
Scissors  
Pencil  
Measure  
Tape  
6 INSTALLATION HARDWARE  
The INSTALLATION HARDWARE (items 1 - 7 ) packed with  
the oven should contain the following:  
Mounting Plate  
Item  
Name  
Quantity  
1
Wood Screw 5 x 35 mm  
Toggle Bolt ³⁄₁₆"  
6
4
2
2
1
4
1
2
Figure 5  
2
3
4
5
6
7
8
Top Cabinet Screw 5 x 85 mm  
Flat Washer 30 mm diameter  
Grommet  
Tapping Screw 4 x 8 mm  
Exhaust Damper Assembly  
Grease Filter  
Figure 4  
Parts shown not to common scale.  
E3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
(B)HORIZONTAL EXHAUST: OUTSIDE VENTILATION  
8 VENTILATION SYSTEM  
(PREPARING OVEN FOR INSTALLATION)  
1. Remove and save 2 screws from back edge and 1 screw  
from the top center of Fan Cover Bracket. Remove Fan  
Cover Bracket by sliding it in the opposite direction of the  
arrow on the Fan Cover Bracket, as shown in Figure 7.  
This microwave oven/hood is designed for adaptation to three  
types of hood ventilation systems. Select the type required  
for your installation.  
2. Withdraw Hood Fan Unit carefully and slip wires out of  
Wire Box. See Figure 8.  
RECIRCULATING — non-vented, ductless.  
Follow installation procedure (A). Recirculating requires  
the use of the Charcoal Filter, which has already been  
installed in the oven.  
CAUTION: Do not pull or stretch hood fan wiring.  
3. Rotate the Hood Fan Unit and turn end-over-end so that  
the fan blade openings are facing the back of the oven.  
Replace Hood Fan Unit into the oven. Be careful not to  
pinch the lead wire between the inner bracket and the  
Hood Fan Unit. See Figure 9.  
HORIZONTAL EXHAUST — outside ventilation.  
Follow installation procedure (B).  
VERTICAL EXHAUST — outside ventilation.  
Follow installation procedure (C).  
4. Put the lead wire into Wire Box. See Figure 10.  
(A) RECIRCULATING: NON-VENTED, DUCTLESS OPERATION  
1. The unit is shipped assembled for recirculating.  
5. Replace the Fan Cover Bracket by sliding it into the slits  
in the same direction as the arrow on the Fan Cover  
Bracket. Make sure the fan blades are visible through  
the rear openings in the oven before proceeding. Attach  
Fan Cover Bracket to unit with 3 screws, which were  
removed in Step 1 above. See Figure 11. The Hood Fan  
Unit is now rotated for horizontal exhaust operation.  
2. The Exhaust Damper Assembly is not required for  
recirculating exhaust.  
3. Charcoal Filter, included with the unit, is required for  
recirculating exhaust. Attach the Charcoal Filter to the  
upper side of the oven by sliding into the tabs. See  
Figure 6. The Charcoal Filter should be replaced every 6  
to 12 months, depending on use.  
6. Attach the Exhaust Damper Assembly to the back of the  
unit. See Figure 10. Use two Tapping Screws 4 x 8 from  
the INSTALLATION HARDWARE and tighten into place.  
Tabs  
Tabs  
Figure 8  
Figure 6  
Fan Cover Bracket  
Back of  
Oven  
Figure 7  
Figure 9  
E4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
Fan Cover Bracket  
Rotate 90°  
Figure 11  
Exhaust Damper  
Assembly  
9 OVEN INSTALLATION  
THIS OVEN CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING  
TO THE MOUNTING INSTRUCTIONS FOUND ON BOTH TEMPLATES.  
Tapping Screw  
THE NEXT STEP IS TO READ AND FOLLOW MOUNTING INFORMATION  
ON BOTH TOP CABINET AND WALL TEMPLATES.  
Figure 10  
NOTE: THIS OVEN SHOULD BE ATTACHED TO AT LEAST ONE WALL  
STUD.  
8 VENTILATION SYSTEM  
MOUNTING PLATE  
(PREPARING OVEN FOR INSTALLATION)  
1. Separate 4 Toggle Bolts, packed in the INSTALLATION  
HARDWARE, from the Toggle Nuts.  
(C) VERTICAL EXHAUST: OUTSIDE VENTILATION  
IMPORTANT  
2.  
Use the mounting template  
provided to Use wood screws to attach mounting  
plate to the stud or studs. Use Toggle Bolts to attach  
mounting plate through the holes UNLESS THOSE  
HOLES ARE LOCATED ON THE STUD. Insert one  
Toggle Bolt where appropriate (these correspond  
to holes of the Wall  
1. Remove and save 2 screws from back edge and 1 screw  
from the top center of the Fan Cover Bracket. Remove  
Fan Cover Bracket by sliding it in the opposite direction  
of the arrow on the Fan Cover Bracket as shown in  
Figure 7.  
2. Withdraw Hood Fan Unit carefully and slip wires out of  
Wire Box. See Figure 8.  
CAUTION: Do not pull or stretch hood fan wiring.  
Template) and put the  
Toggle Nuts onto the  
Toggle Bolts. Figure 13.  
Refer to instructions in  
Wall Template.  
3. Turn the Hood Fan Unit end-over-end. Rotate the Hood  
Fan Unit 90˚ so that the fan blade openings are facing  
upward. Replace Hood Fan Unit into the oven. Be careful  
not to pinch the lead wire between the inner bracket and  
the Hood Fan Unit. See Figure 11.  
3. Position the Mounting Plate with the Toggle Bolts  
attached at the wall location and insert Toggle Nuts  
and Bolts through the holes in the wall with the Toggle  
Nuts closed. Figure 15. Use Wood Screws to attach the  
Mounting Plate to studs.  
4. Put the lead wire into Wire Box. See Figure 11.  
5. Replace the Fan Cover Bracket by sliding it into the slits  
in the same direction as the arrow on the Fan Cover  
Bracket. Make sure the fan blades are visible through  
the top openings in the oven before proceeding. Attach  
the Fan Cover Bracket to unit with 3 screws, which were  
removed in Step 1 above. See Figure 10. The Hood Fan  
Unit is now rotated for vertical exhaust operation.  
NOTE: Before insertion, be sure you leave a space more  
than the thickness of the wall between the Mounting Plate  
and the end of each of the Toggle Nuts (in the closed  
position). If you do not leave enough space, the Toggle  
Nut will not be able to open on the other side of the wall.  
Also, once a Toggle Nut opens, it cannot be withdrawn  
from the hole; therefore make sure all of the Toggles are  
in the correct position before insertion.  
6. Attach the Exhaust Damper Assembly to the fan cover  
bracket on the top of the outercase cabinet after mounting  
the oven. To attach the Exhaust Damper Assembly, refer  
to MOUNTING OVEN TO THE WALL, page 6 Figure 17.  
4. Align the Mounting Plate carefully and hold in position  
while tightening Toggle Bolts. Pull Toggle Bolt toward  
you and turn clockwise to tighten. Figure 14.  
E5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
9 OVEN INSTALLATION  
cont.  
Toggle Bolt  
Toggle Nut  
Mounting Plate  
Figure 12  
Space more  
than wall  
thickness  
Figure 15  
Figure 14  
Wall  
Figure 13  
MOUNTING OVEN TO THE WALL  
Two people are recommended to attach the Microwave Oven/  
Hood to the Mounting Plate.  
Tapping Screw  
1. Thread the power supply cord through the hole made in  
the bottom of the top cabinet.  
Figure 16  
2. Install the oven by tilting it forward and sliding it onto the  
tabs of the Mounting Plate. Rotate the oven up so it rests  
against the wall. See Figure 15.  
Tapping Screw  
3. Use the two Top Cabinet Screws and two Flat Washers,  
supplied in the INSTALLATION HARDWARE, to attach  
the unit to the top cabinet. See Figure 16.  
4. Secure the bottom of the oven to the Mounting Plate  
by using two Tapping Screws 4 x 8 mm from the  
INSTALLATION HARDWARE. See Figure 16.  
Figure 17  
E6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
CHECKLIST FOR INSTALLATION  
1. Make sure the unit has been installed according to all of the  
Installation Instructions and the Wall and Top Cabinet Templates.  
2. Plug in the power cord.  
3. Keep the Operation Manual.  
E7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
E8  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edelbrock Automobile Parts 17932 User Manual
Electro Voice Speaker EVI 15 User Manual
Fisher Price Baby Toy B1472 User Manual
Fisher Price Model Vehicle 74305 User Manual
FMI Indoor Fireplace VCM 36Q User Manual
FujiFilm Printer MP 300 User Manual
Garland Cooktop M48 23R User Manual
GE Microwave Oven 164D3370P003 User Manual
Gemini Musical Instrument PS 676i User Manual
Gigabyte Computer Hardware GA M52S S3P User Manual