®
Fisher-Price
Instructions
™
Backyard Treehouse
Model Number: 75972
If you experience a problem with this product, or are missing a part, please call us
at 1-800-432-KIDS, rather than return this product to the store.
Please save these instructions for future reference.
Adult assembly is required.
No tools needed for assembly.
Weight Limit: 300 lbs.
The Fisher-Price® Backyard Treehouse™ is designed to easily attach to other
Fisher-Price® outdoor playsets equipped with a connecting feature. Do not attach other
manufacturer’s playsets to this Fisher-Price® product.
1
2
Ages: 1 / to 6 years.
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement and Play Area Surfacing
Before assembling this product, select and prepare a play area.
Select a Play Area
Select an area on level ground at least 6 feet from any structure or obstruction such as a fence, garage, house, overhanging
branches, washing lines or electrical lines.
Prepare a Surface
Following are guidelines from the Consumer Product Safety Commission’s Handbook for Public Playground Safety to mini-
mize injuries that can result from falls. These guidelines apply to playground equipment including but not limited to swing sets
and climbing equipment.
Hard surfacing materials are not suitable for use under this equipment. Earth surfaces such as soils and hard packed dirt are
also not recommended because their shock absorbing properties can vary depending on climatic conditions such as mois-
ture and temperature. Grass and turf are not recommended because their effectiveness in absorbing shock during a fall can
be reduced considerably due to wear and environmental conditions.
Acceptable surfacing materials are available in two basic types: loose-fill and unitary.
Loose-fill materials can have acceptable shock absorbing properties when installed at a sufficient uncompressed depth of at
least 6 inches. These materials include sand (fine and coarse), gravel (fine and medium) and shredded wood products (wood
mulch, shredded bark, wood chips). Loose-fills should not be installed over hard surfaces such as asphalt or
concrete.
The depth of any loose-fill material could be reduced during use resulting in different shock-absorbing characteristics. For
this reason, a depth greater than the minimum recommended should be considered.
Unitary materials are generally rubber mats or a combination of rubber-like materials held in place by a binder that may be
poured in place at the playground site and cures to form a unitary shock absorbing surface.
Maintenance
Periodically check to be sure equipment has adequate protective surfacing under and around it. Inspect surfacing material for
deterioration. Check loose surfacing material for foreign objects or debris. Also look for compaction and reduced depth, with
special attention to heavy use areas such as those under swings and slide exit regions.
Message to Parents
Thank you for purchasing the Fisher-Price® Backyard Treehouse™. The Backyard Treehouse™ should be assembled by an
adult, preferably by two adults. Please read these instructions carefully and identify all parts before assembly. Refer to the
parts illustration on the next page for identification.
Questions? We’d like to hear from you!
Call Fisher-Price® Consumer Affairs, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday. Hearing-
impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Or, write to: Fisher-Price® Consumer Affairs,
636 Girard Avenue, East Aurora, New York 14052.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
If you experience a problem with this product, or are missing a part, please call us
at 1-800-432-KIDS, rather than return this product to the store.
Left Roof
Right Roof
Tree Top
Shutter- 2
F
is
h
e
r-
P
®
ri
ce
Ladder
Panel
Table
Top
Back
Panel
Front
Trunk
Panel
Ramp
Safe
Door
Mailbox Door
Wall Panel
Platform
Not Shown:
Vinyl Label - 2
Box of Chalk
Phone
• Please save all packaging material until assembly is complete to ensure that no parts are discarded.
• Before assembling the Backyard Treehouse™, please wipe each part with a clean, dry cloth.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Upper
Peg
Chalkboard
Safe
Door
Front Trunk
Panel
Front Trunk
Panel
Ladder
Panel
Lower
Peg
Lower
Hinge
Hole
Slots
Upper Hinge Hole
• Position the front trunk panel on a flat surface with the
inside facing up.
Hooked
Tabs
Helpful Hint: The safe door may be difficult to attach to the
front trunk panel. Place a cloth under the front trunk panel
to protect the surface. Apply a small amount of liquid soap
to the pegs on the safe door.
Safe
• Stand the front trunk panel upright.
• Position the safe door with the dial facing up. Insert the
safe door lower peg into the lower hinge hole in the front
trunk panel.
• Firmly push down on the safe door to snap the upper peg
into the upper hinge hole in the front trunk panel.
• Position the ladder panel so that the chalkboard is toward
the safe on the front trunk panel.
• Insert the hooked ladder panel tabs into the slots in the
front trunk panel.
Upper Half
Chalkboard
Label
Front Trunk
Panel
Ladder
Panel
Label
Ladder
Panel
Bottom
Edge
Tabs
Slots
• Locate the ladder panel.
• Make sure the area where the chalkboard label will be
applied is clean and dry.
• Bend the chalkboard label in half lengthwise.
• Remove the backing from the upper half of the label.
Helpful Hint: You may need the help of another person with
this assembly step.
• Align the bottom edge of the label with the bottom edge
of the chalkboard outline on the ladder panel.
• Turn the assembly upside down so that the ladder panel
rests on a flat surface.
• Apply the top half of the label to the ladder panel and
smooth the label downward.
• Remove the backing from the lower half of the label.
• Smooth the label downward.
• Lift the assembly up and pound the ladder panel onto the
surface to lock the tabs on the ladder panel into the slots
in the front trunk panel.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Mailbox Label
Mailbox Door
Front Trunk
Panel
Pegs
Hinge
Holes
Table
Top
Wall
Panel
Supports
Tab
Ladder
Panel
• Make sure the area where the mailbox label will be
applied is clean and dry.
• Bend the mailbox label in half and remove the backing.
• Apply the mailbox label to the mailbox door.
• For best adhesion, try to avoid applying the label more
than once.
Please Note: The mailbox label may already be applied to
the mailbox door.
• Position the wall panel on a flat surface with the outside
facing up.
• Insert one of the mailbox door pegs into one of the hinge
holes in the wall panel.
• Position the assembly so that the ladder panel is laying on
a flat surface.
Helpful Hint: Push the front trunk panel back, to allow for
easier assembly.
• With the table top at an angle, completely insert the tab
on the table top into the slot above the supports on the
ladder panel.
• Rotate the table top toward the supports.
• Fit and snap the other mailbox door peg into the other
hinge hole in the wall panel.
Table Top
Table Top
Wall
Panel
Ladder
Panel
Ladder
Panel
Ladder
Panel
|