Fisher Price Baby Monitor 71565 User Manual

Sound ‘n Lights Monitor  
Model Number 71565  
Please read these instructions and keep them for future reference.  
Includes two AC adaptors to power the transmitter and receiver.  
The receiver also runs on battery power (9v alkaline – not included).  
®
Fisher-Price  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Your Sound ’n Lights Monitor  
C
16  
6
3
11  
17  
2
4
19  
10  
13  
14  
N
O
F
F
O
OFF ON  
POWER  
9
POWER  
5
B
A
B
A
CHANNEL  
CHANNEL  
12  
®
ce  
-Pri  
er  
ish  
F
®
Fis  
he  
r-P  
ri  
ce  
15  
7
18  
1
8
1
2
Transmitter . . . . . . . . . . . . . . .Sends (transmits) sounds to the receiver.  
On/Off Switch . . . . . . . . . . . . .Turns the transmitter powerONorOFF”.  
Power Indicator . . . . . . . . . . .Lights up to let you know the transmitter isON”.  
Microphone . . . . . . . . . . . . . . .For clear audio pick-up.  
3
4
5
6
2-Position Channel Switch . . . .Allows you to change channels if interference occurs.  
Flexible Antenna . . . . . . . . . . .Aids in sound transmission.  
7 AC Adaptor Socket (on side). . .For use with the provided AC adaptor.  
8
Receiver . . . . . . . . . . . . . . . . .Receives signal from the transmitter to hear sound.  
9 Volume Dial . . . . . . . . . . . . . . .Controls the volume of sound.  
10 Power Indicator . . . . . . . . . . . .Lights up to let you know the receiver isON”.  
11 Moving Lights Display . . . . . . .Shows sounds are being transmitted.  
12  
Speaker . . . . . . . . . . . . . . . . . .Allows you to hear baby’s sounds.  
13 2-Position Channel Switch . . . .Allows you to change channels if interference occurs.  
14  
AC Adaptor Socket (on side). . .For use with the provided AC adaptor.  
15  
Battery Compartment Door . . .For easy access to battery compartment.  
16 Flexible Antenna . . . . . . . . . . .Aids in sound reception.  
17  
Belt Clip (on back) . . . . . . . . . .For added portability when moving from room to room.  
18 AC Adaptors (2 included) . . . .Both the transmitter and receiver operate on standard household current  
(120v AC outlet) with either of these AC adaptors.  
19  
On/Off Switch . . . . . . . . . . . . .Turns the receiver powerONorOFF”.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
• If a removeable rechargeable battery is used, it is only to  
be charged under adult supervision.  
• A rechargeable battery is to be removed from the  
product before it is charged.  
• If you use a battery charger, it should be examined  
regularly for damage to the cord, plug, enclosure and  
other parts. Do not use a damaged battery charger until  
it has been properly repaired.  
Battery Installation  
D
The receiver operates either with the AC adaptor  
included with your Sound ’n Lights Monitor  
or with a 9 volt alkaline battery.  
9V  
(LR6)  
Set-Up and Use  
E
Shown Actual Size  
IMPORTANT NOTE! To prevent entanglement, never  
place the transmitter in a crib or playpen. Place the  
transmitter, receiver and AC adaptor cord(s) out of  
baby’s reach.  
Battery Compartment Door  
Antenna  
On/Off Switch  
Channel Switch  
Power  
Indicator  
AC Adaptor Jack  
ON  
OFF  
ER  
W
PO  
B
A
L
NE  
AN  
CH  
Finger  
Tab  
®
e
ic  
r
r-P  
e
h
is  
F
• Locate the battery compartment door on the bottom of  
the receiver.  
• Push the finger tab on the battery compartment door to  
open the battery compartment door.  
Socket  
AC Adaptor  
Plug  
• Snap the terminals of a fresh 9v alkaline battery into the  
connectors.  
Transmitter  
• Close the battery compartment.  
Please Note:  
• Remove the battery during long periods of non-use.  
Always remove an exhausted battery from the product.  
Battery leakage and corrosion can damage the product.  
• Never short circuit the battery terminals.  
• A non-rechargable battery is not to be recharged.  
• Place the transmitter in the same room with your child.  
For best sound pick-up, point the microphone directly  
toward the crib or play area. Make sure the antenna  
points upward for best transmission.  
• For best transmission, unwrap and fully extend the  
AC adaptor cord. Insert the AC adaptor jack into the  
transmitter socket.  
• Insert the plug into a standard wall outlet.  
• Set the transmitter channel switch to the same channel  
as the receiver.  
• Only a battery of the same or equivalent type as  
recommended in theBattery Installationinstructions is  
to be used.  
• Slide the on/off switch on the front of the transmitter to  
theONposition.The power indicator will light.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
• If you will be using the AC adaptor to power the  
receiver, unwrap and fully extend the AC adaptor cord  
for best reception. Insert the AC adaptor jack into the  
side of the receiver.  
Antenna  
• Insert the plug into a standard wall outlet.  
• Check to be sure the channel switch on the receiver is  
set to the same channel as the transmitter.  
• Slide the on/off switch on the front of the receiver to  
theONposition. The power indicator will light.  
• Adjust the volume by turning the volume dial to a  
comfortable level.  
Moving Light Display  
Power Indicator  
On/Off Switch  
Channel Switch  
AC Adaptor Jack  
OFF ON  
POWER  
A
B
CHANNEL  
Volume Dial  
• The moving light display will light when sound is  
received by the receiver.  
• If all five bars in the moving light display light:  
®
e
ric  
r-P  
he  
Fis  
– The receiver power isONand the transmitter power  
isOFF”. (Turn the transmitter powerON”.)  
Plug  
AC Adaptor  
– The receiver is out of range of the transmitter. (Move  
the receiver closer to the transmitter.)  
– The receiver and the transmitter are not on the same  
channel. (Set the channel switches on the transmitter  
and receiver to the same channel.)  
Receiver  
AC Adaptor Use  
– Loud sounds are transmitting.  
Please Note:The moving light display will not light if the  
battery is weak, even though you may still hear sounds.  
Replace the battery with a fresh, 9v alkaline battery.  
Antenna  
• To protect your privacy, be sure to turn the transmitter  
and receiverOFFwhen not in use.  
Moving Light Display  
On/Off Switch  
Channel Switch  
Power Indicator  
Volume Dial  
OFF ON  
POWER  
A
B
CHANNEL  
®
Fis  
he  
r-P  
ric  
e
Receiver  
Battery Use  
• Decide whether you will use the AC adaptor or a  
9v alkaline battery to power the receiver. If you will be  
using the receiver near an outlet, we recommend using  
the AC adaptor.  
• Place the receiver where you can hear/see it. Or, wear  
the receiver using the convenient belt clip. Make sure  
the antenna points upward for best reception.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
One (1) Year  
Sound Reception  
F
I
Limited Warranty  
It is very important to test the sound  
reception of the Sound ’n Lights Monitor before  
first-time use and whenever you change the  
location of the transmitter.  
Fisher-Price, Inc., 636 Girard Avenue, East Aurora,  
New York 14052, warrants that the Sound ’n Lights  
Monitor is free from all defects in material and workman-  
ship when used under normal conditions for a period of  
one (1) year from the date of purchase.  
• Test the Sound ’n Lights Monitor transmission and  
reception. In the room you intend to use the transmit-  
ter, have an adult speak into the transmitter. (If an adult  
is not available,use a ticking clock or radio.) Place the  
receiver in the room in which you intend to use the  
receiver. Adjust the receiver location or volume dial  
until you hear sounds clearly.  
• If you experience interference (buzzing, static, etc.)  
while using one channel setting, switch both units to  
the other channel. Selecting a channel is usually a  
one-time adjustment.  
Should the product fail to perform properly, we will  
repair or replace it, free of charge. Purchaser is respon-  
sible for shipping the product to the address indicated  
above and for all associated freight and/or insurance cost.  
Fisher-Price, Inc. will bear the cost of shipping the  
repaired or replaced item to you.This warranty is void if  
the owner repairs or modifies the product.This warranty  
excludes any other liability other than the above  
mentioned, including but not limited to any incidental  
or consequential damages.  
• If interference occurs on both channels or if further  
problems develop, please refer to theProblems and  
Solutions Guidebeginning on page 7.  
SOME STATES DO NOT ALLOW THE EXCLUSION OR  
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES, SO THE ABOVE LIMITATION OR EXCLU-  
SION MAY NOT APPLY TO YOU.  
Care  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL  
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS  
WHICH VARY FROM STATE TO STATE.  
G
• Keep the Sound ’n Lights Monitor free from dust.  
Important Note:The electronic components in the  
Sound’n Lights Monitor are not designed for consumer  
repair. Evidence of any attempt at consumer repair will  
void the warranty. Return the AC adaptors, transmitter and  
receiver (please remove the battery from the receiver  
before sending to Fisher-Price, Inc. for service).  
• The outer surface of the transmitter and receiver can be  
cleaned with a cloth lightly dampened with a mild  
cleaning solution.  
• Do not immerse any part of the Sound ’n Lights Monitor.  
FCC Note  
H
(United States only)  
Sound ’n Lights Monitor  
Model Number: 1565  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference and  
(2) This device must accept any interference received,  
including interference that may cause undesired  
operation.  
Fisher-Price, Inc.  
Consumer Affairs Department  
636 Girard Avenue  
East Aurora, New York 14052  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problems and Solutions Guide  
J
IMPORTANT! If you have a problem with the Sound ’n Lights Monitor, first check the Problems and  
Solutions Guide below. If you still experience a problem with the Sound ’n Lights Monitor, call Fisher-Price  
Consumer Affairs, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday.  
Hearing-impaired consumers using TTY/TDD equipment,  
®
®
please call 1-800-382-7470. Or, write to: Fisher-Price Consumer Affairs,  
636 Girard Avenue, East Aurora, New York 14052.  
PROBLEM  
PROBABLE CAUSE  
Transmitter not turnedON”  
Power is turnedOFF”  
SOLUTION  
Transmitter power  
indicator does not light  
Turn the transmitterON”.  
Make sure that any light switches that control power flow to  
the wall outlet areON”.  
Make sure house fuses and circuit breakers areON”.  
AC adaptor not properly connected  
AC adaptor problem  
Check AC adaptor jack-to-socket and plug-to-outlet connections.  
Test the transmitter using the other AC adaptor included with this  
product. If the transmitter works with the other AC adaptor, call  
Fisher-Price® at 1-800-432-KIDS to replace the broken AC adaptor.  
Receiver power  
indicator does not light  
Receiver not turnedON”  
Power is turnedOFF”  
Turn the receiverON”.  
Make sure that any light switches that control power flow to the  
wall outlet areON”.  
Make sure house fuses and circuit breakers areON”.  
AC adaptor not properly connected  
AC adaptor problem  
Check AC adaptor jack-to-socket and plug-to-outlet connections.  
Test the receiver using the other AC adaptor included with this  
product. If the receiver works with the other AC adaptor, call  
Fisher-Price® at 1-800-432-KIDS to replace the broken AC adaptor.  
Weak or dead battery  
Replace the battery in the receiver with a fresh 9v alkaline  
battery or use the AC adaptor.  
No sound  
Channel switches not on same setting  
Set channel switch on transmitter and receiver to the same  
channel.  
Signal interference due to other nursery  
monitors, cordless telephones, etc.  
Change the channel setting on both the transmitter and the  
receiver.  
Identify and eliminate the source of interference.  
Test reception by moving the transmitter and/or receiver to  
different locations throughout the house. Relocate the  
transmitter and/or receiver.  
Out of range or insufficient signal  
Test reception by moving the transmitter and/or receiver to  
different locations throughout the house. Relocate the  
transmitter and/or receiver.  
Volume not turned up  
Adjust volume control on receiver.  
Improper antenna position  
Make sure the antenna on the transmitter and receiver are  
pointing upward.  
Weak or dead battery in receiver  
AC adaptor not properly connected  
Replace the battery in the receiver with a fresh 9v alkaline  
battery or use the AC adaptor.  
Check AC adaptor jack-to-socket and plug-to-outlet connections.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROBLEM  
PROBABLE CAUSE  
SOLUTION  
Weak reception  
Out of range or insufficient signal  
Test reception by moving the transmitter and/or receiver to  
different locations throughout the house. Relocate the transmitter  
and/or receiver.  
AC adaptor cord(s) not fully extended  
Improper antenna position  
Fully extend AC adaptor cord(s).  
Make sure antennas are pointing upward.  
Receiver moving light  
display does not light  
Weak or dead battery in receiver  
Replace the battery in the receiver with a fresh 9v alkaline  
battery or use the AC adaptor.  
Interference  
(buzzing, static, etc.)  
Signal interference due to other  
nursery monitors or cordless  
telephones, etc.  
Change channel switch on both transmitter and receiver to the  
other channel.  
Identify and eliminate source of interference. Do not use more  
than one receiver or transmitter at the same time in the same  
house.  
Channel switches not on  
same setting  
Check channel switch on transmitter and receiver to be sure  
they are on the same channel.  
Feedback  
(squealing or whistling)  
Receiver is too close to the  
transmitter  
Move receiver further away from transmitter.  
Volume is set too high  
Lower volume on the receiver.  
All five bars on the  
receiver moving light  
display light  
Receiver power isONbut  
transmitter power isOFF”  
Turn the transmitter powerON”.  
Out of range or insufficient signal  
Move the receiver closer to the transmitter.  
Channel switches not on same  
setting  
Check channel switches on transmitter and receiver to be sure  
they are on the same channel.  
AC adaptor not properly connected  
to transmitter  
Check AC adaptor jack-to-socket and plug-to-outlet connections.  
If you have any questions about this product:  
In Canada, call 1-800-567-7724, or write to:  
Mattel/Fisher-Price, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.  
In Great Britain, telephone 01734 770488.  
In Australia, call the Fisher-Price Australian Consumer Advisory Service toll-free at 1-800-800-812, or write to:  
Fisher-Price, Mattel Pty. Limited, 461 Plummer Street, Port Melbourne,Victoria 3207.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  

Dyson Vacuum Cleaner DC11 User Manual
Estate Range W10162222A User Manual
EVGA Computer Drive 128 P2 KN01 User Manual
Extron electronic TV Cables DTP T HWP 231 D User Manual
Ford Automobile 1999 Escort User Manual
Franke Consumer Products Cooktop FDF 9044 I XS ECS User Manual
Gas Fired Products Electric Heater HS125LP User Manual
Gemini Speaker RS 408 User Manual
GE Monogram Refrigerator ZS48N User Manual
GE Universal Remote 24938 User Manual