Freestanding cooker
Installation instructions
and User guide
OR90SDBGFX models
NZ AU
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Contents
Safety and warnings
Installation instructions
Using your seven-function oven for the first time
Setting the clock
Using your oven
Cooking functions
Using the rotisserie
Using the electronic timer
Automatic cooking
Using your gas cooktop
Care and cleaning
Troubleshooting
2
6
18
19
20
21
23
24
25
26
30
44
45
Warranty and service
Important!
SAVE THESE INSTRUCTIONS
The models shown in this User Guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
contact your local Fisher & Paykel dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Safety and warnings
Installation
WARNING!
Electrical Shock Hazard
Always disconnect the cooker from the mains electricity supply before
carrying out any maintenance operations or repairs.
Failure to follow this advice may result in death or electrical shock.
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
Important safety instructions
General
To avoid hazard, follow these instructions carefully before installing or using this product.
Please make this information available to the person installing the product as it could reduce
your installation costs.
These products are registered:
This appliance must be installed in accordance with these installation instructions, local
gas fitting regulations, municipal building codes, water supply regulations, electrical wiring
regulations, AS/NZS5601.1:2010 - Gas Installations and any other relevant statutory regulations.
Failure to install the cooker correctly could invalidate any warranty or liability claims.
Some appliances have a protective film. Remove this film before using the cooker.
Do not modify this appliance.
Do not operate your appliance by means of an external timer or separate remote-control system.
This appliance is to be installed and serviced only by an authorised person.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Safety and warnings
Electrical
This cooker is to be installed and connected to the electricity supply only by an authorised person.
If the installation requires alterations to the domestic electrical system, call a qualified
electrician. The electrician should also check that the electrical system is suitable for the
electricity drawn by the cooker.
The appliance must be connected to the mains electricity supply, checking that the voltage
corresponds to the value given in the rating plate and that the electrical cable sections can
withstand the load specified on the plate.
A suitable disconnection switch must be incorporated in the permanent wiring, mounted and
positioned to comply with the local wiring rules and regulations. The switch must be of an
approved type installed in the fixed wiring and provide a 3 mm air gap contact separation in all
poles in accordance with the local wiring rules.
In Australia and New Zealand, a switch of the approved type with a 3 mm air gap must be
installed in the active (phase) conductor of the fixed wiring.
The switch must always be accessible.
The power supply cable must not touch any hot parts and must be positioned so that it does not
exceed 75 OC at any point.
To connect the cooker to the mains electricity supply, do not use adapters, reducers or branching
devices as they can cause overheating and burning.
This cooker must be connected to a suitable double pole control unit adjacent to the cooker. No
diversity can be applied to this control unit.
If the electrical supply cord is damaged, it must only be replaced by an authorised person.
This cooker must be connected to electrical supply using V105 insulated cable.
The cooker must be earthed.
Power supply
220-240V~ 3680W 50/60Hz
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Safety and warnings
Operation
Your freestanding cooker has been carefully designed to operate safely during normal cooking
procedures. Please keep the following guidelines in mind when you are using it:
WARNING!
Explosion Hazard
Do not store flammable materials such as gasoline near the cooktop.
Do not store flammable material in the oven or storage compartment.
Do not spray aerosols near the cooktop during use.
Failure to follow this advice may result in death or serious injury.
WARNING!
Electrical Shock Hazard
Switch the cooker off at the wall before replacing fuses or the oven lamp.
Failure to do so may result in death or electrical shock.
WARNING!
Hot Surface Hazard
Accessible parts may become hot when this cooker is in use.
To avoid burns and scalds keep children away.
Do not touch hot surfaces inside the oven.
Use oven mitts or other protection when handling hot surfaces such as oven
shelves or dishes.
Take care when opening the oven door.
Let hot air or steam escape before removing or replacing food.
Do not touch the cooktop components, burners, trivets/pan supports or the
base when hot.
Before cleaning, turn the cooker off and make sure it is cool.
Failure to follow this advice could result in burns and scalds.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Safety and warnings
Important safety instructions
Never leave the appliance unattended when in use. Boilover causes smoking and greasy
spillovers that may ignite.
Isolating switch: make sure this cooker is connected to a circuit which incorporates an isolating
switch providing full disconnection from the power supply.
Household appliances are not intended to be played with by children.
Children, or persons with a disability which limits their ability to use the appliance, should have a
responsible person to instruct them in its use. The instructor should be satisfied that they can use
the appliance without danger to themselves or their surroundings.
Safe food handling: leave food in the oven for as short a time as possible before and after
cooking. This is to avoid contamination by organisms which may cause food poisoning. Take
particular care during warmer weather.
Do not place aluminium foil, dishes, trays, water or ice on the oven floor during cooking as this
will irreversibly damage the enamel.
Do not line the walls with aluminium foil.
Do not stand on the door, or place heavy objects on it.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since
they scratch the surface, which may result in shattering of the glass.
Do not use a steam cleaner to clean any part of the cooker.
Do not use an asbestos mat or decorative covers between the flame and the saucepan as this may
cause serious damage to your cooktop.
Do not place aluminium foil or plastic dishes on the cooktop burners.
Do not let large saucepans or frying pans overlap the bench as this can deflect heat onto your
benchtop and damage the surface.
Do not let large saucepans, frying pans or woks push any other pans aside. This could make them
unstable or deflect heat onto your benchtop and damage the surface.
Saucepan handles may be hot to touch. Ensure saucepan handles do not
overhang other gas burners that are on. Keep handles out of reach of children.
If the electrical supply cord is damaged, it must only be replaced by an authorised person.
This cooker is not to be used as a space heater, especially if it is installed in marine craft or in a
caravan.
The use of a gas cooking appliance results in the production of heat and moisture in the room in
which it is installed. Ensure the kitchen is well ventilated. Keep natural ventilation holes open or
install a mechanical ventilation device (mechanical extractor hood).
Prolonged intensive use of the appliance may call for additional ventilation, for example opening
of a window, or more effective ventilation, for example increasing the level of mechanical
ventilation where present.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Installation instructions
Dimensions and clearances
Installation clearances and protection of combustible surfaces shall comply with the current
local regulations eg. AS/NZS5601.1:2010 Gas Installations code. Installation shall comply with
the dimensions in Fig. 1, bearing in mind the following requirements:
Overhead Clearances
In no case shall the clearance above the highest part of the cooker be less than 600 mm or, for
an overhead exhaust fan, 750 mm. AII other downward-facing combustible surfaces less than
600 mm above the cooker surface shall be protected for the full width of the cooking surface in
accordance with the standards noted above. In no case shall the clearance be less than 450 mm.
Rear and Side Clearances
Where the distance from the periphery of the nearest burner to any vertical combustible surface
is less than 200 mm, the surface shall be protected in accordance with the standards to a height
of not less than 150 mm above the cooking surface for the full width or depth of the cooking
surface.
Where the distance from the periphery of the nearest burner to any horizontal combustible
surface is less than 200 mm, the horizontal surface shall be more than 10 mm below the surface
of the cooking surface, or the horizontal surface shall be above the trivet (see requirements for
vertical combustible surfaces above).
Protection of combustible surfaces
The standards above specify that, where required, protection shall ensure that the surface
temperature of combustible surfaces does not exceed 65°C above room temperature.
Do not install the cooker near flammable materials (eg curtains).
Installing the cooker above a plinth without fitting the adjustable feet
In that case the cooker stands directly above the plinth; make sue you provide safety measures
to keep it in place. Revise the installation dimensions accordingly considering that the feet have
the following measures: min 155 mm - max 180 mm.
If you stand the cooker
on a pedestal, make
sure you provide safety
measures to keep it
in place.
500 mm
200 mm
Cooker overall dimensions [mm]
•
•
•
•
height:
product width: 898
depth:
cavity width
min 892 - max 917
600
900
Fig. 1 Dimensions and
distances from cooker
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Installation instructions
Dotted line showing
the position of the
cooker when installed
Locating the area for gas and electrical connection
Area for gas
connection
70.5 mm
70.5 mm
Area for electrical
connection
m(*)
35-60
m(*)
6-281.5
Fig. 2 Area for gas and electrical connections
(*) Depending on
feet adjustment
Fitting the adjustable feet
Important!
It is possible to install the cooker above a plinth without fitting the adjustable feet.
In that case the cooker will stand directly above the plinth; make sure you provide safety measures to
keep it in place.
Fit the adjustable feet before using the cooker.
1
2
Rest the rear of the cooker on a piece of the polystyrene packaging, exposing the base for
fitting the feet.
Fit the four feet by screwing them tight into the support base as shown.
Levelling the cooker
Level the cooker by screwing the feet in or out,
as shown in Fig.5.
Fig. 3 Location of feet
Fig. 4 Top of feet to be
screwed in tightly
Fig. 5 Levelling the cooker
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Installation instructions
Moving the cooker
Important!
To prevent damaging the adjustable feet, ensure
the cooker is always lifted by two people.
Do not lift the cooker by the door handles.
DO NOT DRAG the cooker. Lift the feet clear of the
floor.
Fig. 6 Correctly lifting the cooker
Fig. 7 Incorrectly moving the cooker
Fig. 8 Incorrectly lifting the cooker
C
B
Fixing the backguard
Before installing the cooker, assemble the
backguard “C” .
The backguard “C” can be found packed
A
at the rear of the cooker.
1
2
3
Before assembling, remove any protective
film/adhesive tape.
Remove the two spacers “A” and the
screw “B” from the rear of the cooktop.
Assemble the backguard as shown and
fix it by screwing the central screw “B”
and the spacers “A”.
Fig. 9 Assembling
the backguard
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Installation instructions
Fitting the anti-tilt bracket
Important!
To restrain the appliance and prevent it tipping
accidentally, fit a bracket to its rear to fix it
securely to the wall. Make sure you also fit the
supplied lock pin to the anti-tilt bracket.
65
mm
833 mm
If installing the cooker above a plinth (without
fitting the adjustable feet), revise the
installation dimensions accordingly
considering that the feet have the following
measures: min 155 mm - max 180 mm.
min 210 mm
max 235 mm
(depending on feet adjustment)
0
+ 25
To fit the anti-tilt bracket:
Fig. 10a Fitting the anti-tilt bracket
1
2
After you have located where the cooker
is to be positioned, mark on the wall the
place where the two screws of the anti-tilt
bracket have to be fitted. Please follow the
indications given in Fig10a.
Drill two 8 mm diameter holes in the wall
and insert the plastic plugs supplied.
Pivoting
panel
Important!
Before drilling the holes, check that you will not
damage any pipes or electrical wires.
Fig. 10b Opening the pivoting panel
3
4
Loosely attach the anti-tilt bracket with the
two screws supplied.
Move the cooker to the wall and adjust the
height of the anti-tilt bracket so that it can
engage in the slot on the cooker’s back, as
shown in Fig.10a.
Anti-tilt bracket
attached on the
rear wall
1
Cooker’s
back
5
6
Tighten the screws attaching the anti-tilt
bracket.
Push the cooker against the wall so that the
anti-tilt bracket is fully inserted in the slot
on the cooker’s back.
Lock pin
Slot on the
cooker’s back
7
Access the bracket and fit the lock pin;
Open the pivoting panel (Fig. 10b).
2
Fit the lock pin through the bracket,
as shown (Fig.10c).
Close the pivoting panel.
Lock pin
correctly fitted
Fig. 10c Fitting the lock pin through the bracket
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Installation instructions
Connecting the cooker to the gas supply
The gas connection must be carried out by an authorised person according to the relevant
standards.
Before connecting the appliance to the gas main, mount the brass conical adaptor onto the gas
inlet pipe, upon which the washer has been placed (see Fig.s 11-12 following).
Conical adaptor and washer are supplied with the appliance (packed with conversion kit for use
with Natural gas or LPG).
This appliance is suitable for use with Natural gas or LPG. (Check the “gas type” sticker attached
to the appliance).
For Natural gas, connect the gas supply to the gas pressure regulator which is supplied with
the appliance (Fig.12). Adjust the regulator to obtain a test point pressure of 1 kPa with the two
semi-rapid burners operating at the maximum.
For LPG, connect the gas supply to the test point adaptor which is supplied with the appliance
(Fig.11). Ensure that the supply pressure is regulated to 2.75 kPa.
The connection must be made at the rear of appliance (left or right); the pipe is not to cross the
cooker.
Close off the unused inlet with the cap and sealing washer supplied (Fig. 13).
IMPORTANT: Use two spanners to tighten or loosen the connecting pipe (Fig.13).
Installation with a flexible hose assembly
If this appliance has to be installed with a hose assembly, the installer shall refer to the network
operator or gas supplier for confirmation of the gas type, if in doubt.
When used with a flexible hose, the connector on the wall should be between 450 mm to 500
mm from the floor and 200 mm to 300 mm from the left-hand side of the appliance as viewed
from the front. The hose connection on the appliance shall face downwards.
It is important that the hose does not come in contact with the metal of the appliance and is
secured as per appropriate gas installation codes. A chain 80% of the length of the flexible gas
hose must be used to prevent stress being applied to the hose. The chain should be attached
securely to the product where shown (see Fig.13), and on the wall.
Flexible hose assemblies should be AS/NZS 1869 Class B or Class D certified. The thread
connection shall be Rp ½” (ISO 7-1) male.
Important!
After connection the installer must check that the hose is not kinked, subjected to abrasion or permanently
deformed. The installer must check also that the hose is not near or in contact with any hot surfaces.
The hose assembly shall be as short as practicable and comply with relevant AS5601 / NZS5261
requirements.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Installation instructions
Gas connection for
LPG
Gas connection for
NATURAL GAS
Gas inlet pipe
Nipple
Gas inlet pipe
Nipple
Washer
Washer
Brass conical adaptor
(Thread tight: use
suitable seal)
Brass conical adaptor
(Thread tight: use
suitable seal)
Test
point
Test point adaptor
Gas pressure
regulator
Test
point
Fig. 11 LPG connection
Fig. 12 Natural gas connection
Chain
security
hole
Left gas
inlet pipe
Right gas inlet pipe
Cap
Fitting the cap on the
Fitting the brass conical adaptor
inlet pipe terminal not used
Cooker manifold
(right or left inlet
pipe)
Manifold male
pipe fitting
Washer
G ½”
(ISO 228-1)
male
Washer (#)
Cap (#)
Rp ½”
(ISO 7-1) male
G ½”
(ISO 228-1)
female
Chain
security
anchor
(#) Already fitted on the
right or left inlet pipe
Fig. 13 Gas supply inlets
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Installation instructions
Leak-testing and flame-testing the cooker
After installing the freestanding cooker and connecting the gas supply:
Using a suitable leak detection fluid solution, check each gas connection one at a time by
brushing the solution over the connection.
1
The presence of bubbles will indicate a leak. If there is a leak, tighten the fitting and then
recheck for leaks.
Important! Do not use a naked flame to test for leaks.
2
3
Adjust the test point pressure or supply pressure to the value that is appropriate for the gas
type.
Test the operation of the appliance:
Turn on the appliance gas controls and light each burner individually and in combination.
Check for a well-defined blue flame without any yellow tipping. If any abnormality is
evident, then check that the burner cap is located properly and the injector nipple is
aligned correctly.
Check the minimum burner setting by quickly rotating the gas control dial from the
maximum to the minimum position. The flame must not go out. If you need to adjust the
setting, see ‘Adjusting the minimum burner setting’ following.
4
If satisfacfory performance cannot be obtained, the installer shall check the installation and
notify the local gas supply authority for a gas supply problem, or if it is an appliance problem,
our Customer Service Centre should be called to obtain the nearest authorized Service Agent.
Converting to a different gas type
This appliance is suitable for use with Natural gas or LPG (check the “gas type” sticker attached
to the appliance). To convert from one gas type to another, you need to replace the injectors,
and then adjust the minimum burning setting.
Replacing the injectors
1
2
Remove the trivets and burners from the cooktop.
Using a spanner, remove the injectors (shown in Figs. 14-15-16 following) and replace them with
ones according to the gas type (see the ‘Table for the choice of injectors’).
Fix the warning label (supplied with the conversion kit) at the back of the cooker, near the gas
inlet connections. This label states that the gas cooktop has been converted for use with LPG/
Natural gas.
3
Adjusting the minimum burner setting
4
Follow the instructions on Page 14, ‘Adjusting the minimum burner setting’.
Important!
If you are converting the cooker from Natural gas to LPG,remove the gas pressure regulator
before connecting the cooker to the gas supply and replace with the test point adaptor supplied
with the conversion kit.
If you are converting the cooker from LPG to Natural gas, remove the test point adaptor before
connecting the cooker to the gas supply and replace with the gas pressure regulator supplied
with the conversion kit.
Notes:
- The burners are designed so that regulation of primary air is not required.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Installation instructions
Injector
Injector
Fig. 14 Semi-rapid burner
Fig. 15 Triple-ring wok burner
J
Injectors for
Injector for
outer crown
inner crown
Fig. 16 Dual burner
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Installation instructions
Adjusting the minimum burner setting
Check whether the flame spreads to all burner ports when the burner is lit with the gas valve set
to the minimum position.
If some ports do not light, increase the minimum gas rate setting. Check whether the burner
remains lit even when the gas valve is turned quickly from the maximum to the minimum
position.
If the burner does not remain lit, increase the minimum gas rate setting.
To adjust the minimum gas rate setting:
Semi-rapid and triple-ring burners:
Turn on the burner.
Turn the valve to the MINIMUM position.
Take off the dial.
1
2
3
4
Using a small flat screwdriver, turn the screw (see Fig. 17) to the correct regulation.
Inside crown of dual burner:
1
2
3
4
Turn on the burner.
Turn the valve to the MINIMUM position of the inner crown only.
Take off the dial.
Using a small flat screwdriver, turn the screw (see Fig. 18) to the correct regulation.
Outside crown of dual burner:
1
2
3
4
Turn on the burner.
Turn the valve to the MINIMUM position of the inner and outer crowns.
Take off the dial.
Using a small flat screwdriver, turn the screw (see Fig. 18) to the correct regulation.
Note: for LPG, the regulation screw is normally tightened up.
regulation screw
regulation screw
(outside crown)
regulation screw
(inside crown)
Fig. 17 Adjusting the minimum burner setting:
semi-rapid and triple-ring wok burner
Fig. 18 Adjusting the minimum burner setting:
dual burner
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Installation instructions
Natural gas
LPG
Test Point Pressure [kPa]
BURNER
1.0
2.75
Injector
Orifice Dia.
Gas
Consumption
Injector
Orifice Dia.
Gas
Consumption
[mm]
1.17
1.54
[MJ/h]
6.50
[mm]
0.70
0.98
[MJ/h]
6.30
Semi-rapid
Triple-ring wok
11.88
12.00
0.76
0.50
16.20
16.20
(inner crown)
(inner crown)
(inner and
outer crowns
operating)
(inner and
outer crowns
operating)
Dual
1.23 - no.2
(outer crown)
0.73 - no.2
(outer crown)
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Installation instructions
Wiring diagram
S2
S1
TM
TMS
F1
F2
PR
1a
2a
3a
4a
5a
1
2
3
4
5
P1
P2
1
2
1
N/7
L/8
1a
6a
7a
8a
9a
6
7
8
9
GIR
10a 10
11a 11
LF
LF
A
PA
C
G
CIR
V
S
TL
M
CF
T
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Installation instructions
Wiring diagram key
F1 Oven function selector (switch)
TM Oven thermostat
TMS Safety thermostat
TL
Thermal overload (n.o.)
S1 Oven temperature indicator light
S2 Oven ON indicator light
PR Oven programmer
F2 Rotisserie selector (switch)
GIR Rotisserie motor
LF
S
Oven lamps
Oven bottom heating element
Oven top heating element
Oven grill heating element
C
G
CIR Oven fan (circular) heating element
Oven fan motor
V
CF Cooling fan motor
PA Ignition switches harness
A
M
T
Igniter
Terminal block
Earth connection
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Using your seven-function oven for the first time
2
11
12
1
3
4
5
6
7
8
9
10
Fig. 19 Control panel
1
2
3
4
5
6
Control buttons
Clock display
Function dial
Temperature dial
Front left (triple-ring wok) burner dial
Rear left (semi-rapid) burner dial
7
8
9
Central (dual) burner dial
Rear right (semi-rapid) burner dial
Front right (triple-ring) burner dial
10 Rotisserie dial
11 Function indicator light
12 Temperature indicator light
Before using your new oven, please:
1
2
3
4
Read this user guide, taking special note of the ‘Safety and warnings’ section.
Remove all accessories and packaging. Peel the protective film off all surfaces and accessories.
Set the clock. The oven will not work until the clock has been set.
Slide in the shelves you will need, making sure that:
they are between the two wires of a shelf position;
the stop notches point down;
Stop notch
Guard rail
the guard rail is at the back.
Note: the grill tray should be positioned between
the two wires of a shelf position and orientated
as shown.
5
Heat the oven on maximum for:
60 minutes in the
30 minutes in the
15 minutes in the
position
position
position
Stop
notch
Fig. 20 Correct position of shelves
and grill tray
There will be a distinctive smell while you are
conditioning your oven. This is normal, but make
sure your kitchen is well ventilated during the conditioning.
6
Once cooled, wipe out the oven with a damp cloth and mild detergent, and dry thoroughly.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Setting the clock
Buttons
sets the timer
sets the cooking time for automatic cooking
sets the stop time for automatic cooking
sets the clock, returns oven to manual mode,
cancels automatic cooking
decreases time and beep volume
increases time
Fig. 21 Clock display and control buttons
Illuminated symbols
If the display shows It means that...
Fore more information
flashing with
The clock needs to be set.
See instructions below.
0•00
A
U
T
The oven is set for automatic
cooking.
steadily lit
Automatic cooking has finished
or has been set incorrectly (the
stop time is before the time of
day)
See section ‘Automatic cooking’
flashing and
beeping
O
steadily lit
The timer is set
See section ‘Using the electronic timer’
flashing and
beeping
The time is up
To set the clock
When the power to the appliance is turned on or restored after a power failure, 0•00 and AUTO
will flash in the display.
1
2
Press
Press
.
and
until you have the correct time of the day.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Using your oven
Fig. 22 Function and temperature dials
1
2
Select the function by turning the function dial. The oven lights will come on.
Select the temperature by turning the temperature control dial clockwise. The oven temperature
indicator light, above the temperature dial on the control panel, will glow until the oven has
reached the set temperature, and then it will go out. Note: the temperature indicator light may
glow and go out again during cooking as the oven maintains the set temperature.
When you have finished cooking, turn the function and temperature control dials to the 0 (off)
3
position.
Note: press the
button if AUTO is flashing or steadily illuminated.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Cooking functions
OVEN LAMP
Only the oven light comes on. It remains on in all the cooking functions.
BAKE
The upper and lower heating elements come on. BAKE is the traditional method of cooking. It
is best to cook on only one shelf at a time in this function. Ideal for large cakes and dishes that
bake for several hours.
GRILL
Grill is the most suitable function for ‘finishing off’ many meals, for example browning the top
of potato gratin and frittata. Use Grill to toast bread or to grill your favourite chicken, fish and
steak. Use with the oven door closed and the temperature set to a maximum of 225°C. For best
results, use the topmost shelf position when you want quick browning (eg toast).
DEFROST
Only the oven fan comes on. Use with the temperature dial set to 0 (off). The fan circulates air
around the oven, speeding up the defrosting process by approximately 30%.
Note: this function is not for cooking food.
FAN FORCED
The circular heating element and the fan come on. The oven set on FAN FORCED can cook
several different foods together. Use FAN FORCED for multi-shelf cooking.
FAN GRILL
Both the grill and the fan come on. Use with the oven door closed and the temperature set to a
maximum of 225°C. Ideal for roasting tender cuts of meat and poultry. Use lower shelf positions
for larger items eg a whole chicken.
PASTRY BAKE
Excellent for sweet and savoury pastry foods, for moist breads and brownies and cookies that
you want extra chewy.
FAN BAKE
The upper and lower heating elements and the fan come on. Ideal for dishes like lasagne that
need to brown on top and also single trays of small cakes or biscuits that bake in less than an
hour.
Important!
Safe food handling: leave food in the oven for as short a time as possible before and after cooking or
defrosting. This is to avoid contamination by organisms which may cause food poisoning. Take particular
care during warmer weather.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Cooking functions
Notes on baking:
Preheat the oven before baking.
Do not place anything, including water or ice, on
the oven floor.
Remove the fat filter before baking.
Use the fat filter when roasting meat and poultry on
FAN BAKE, FAN GRILL or FAN FORCED. It helps to keep
your oven clean and reduces splatter and smoking.
Always clean the filter after every use. See ‘Care and cleaning’.
Remove the fat filter before baking.
Baking chart
Fig. 23 Fat filter
The settings in the following chart are guidelines only. Follow the instructions in your recipe or
on packaging and be prepared to adjust the oven settings and baking times to achieve the best
possible results for you.
Shelf positions are counted from the oven floor up (1 is the lowest, 4 or 6 the highest).
Arrange oven shelves before you turn the oven on, then preheat the oven to the required
temperature (until the temperature indicator light goes out).
Single shelf positions below use the flat oven shelf; where a multi shelf arrangement is
recommended, the higher position uses the step-down shelf.
Due to the width of the oven, a single shelf can usually accommodate double the standard
recipe.
Food
Note on
arrangement
Shelf
Best
Temperature (OC) Time
position(s) function
2
180-190
160-170
210-230
210-230
20-30 mins
single shelf
multi shelf
single shelf
multi shelf
Bake
Small cakes
Scones
1 and 3
2
30-40 mins
15-20 mins
15-20 mins
Fan Forced
Bake
1 and 3
Fan Forced
two small pans (20
cm),on single shelf
2
2
2
170-180
175
30-45 mins
30-40 mins
1 hr 30 mins
Bake
Bake
Bake
Sponge
one large pan
(26 cm)
two pans (21 cm)
on single shelf
Light fruit cake
155-165
exact baking time
will depend on size
Rich fruit cake
Apple pie
2
1
1
130-150
185
3-6 hrs
Bake
Bake
Bake
single shelf
35-45 mins
180-200, then
140-150
15, then
30-40 mins
Custard tart
single shelf
Quiche
single shelf
single shelf
single shelf
1
1
1
180-200
100-120
210-230
30-40 mins
1 hr
Bake
Bake
Bake
Meringues
Bread rolls
15-20 mins
2 x 12 muffin trays
on single shelf
Fan Forced
Muffins
3
190-200
10-15 mins
or Fan Bake
10 mins with
beans, then
10 mins
Pastry case
(baked ‘blind’)
one 21 cm flan tin
1
200
Pastry Bake
without
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Using the rotisserie
1
2
Prepare the rotisserie supports.
Place the grill tray on the benchtop.
Insert the supports into the lock studs.
Push the supports all the way down to lock
them in firmly.
Lock stud
Secure the meat.
Important!
Fig. 24a Prepare the rotisserie supports
Take care, the forks are sharp!
When securing the meat, ensure that:
the skewer goes through the centre of the
meat
Rotate the fork screws to
loosen and tighten
the forks hold the meat firmly in place
the fork screws are tightened
there are no loose or projecting parts.
Poultry should be trussed.
Fork
Note: the rotisserie can rotate up to 6 kg of meat.
3
4
Position the skewer on the supports.
Skewer
Fig. 24b Secure the meat
Place the skewer on the supports, and check
that the meat does not touch the grill tray.
Twist the handle off. It must not be left in
the oven.
Place the rotisserie in the oven.
Slide the grill tray all the way to the back on
shelf position 1.
Push the skewer through the hole cover on
the right-hand wall of the oven, then insert
it fully into the rotisserie drive hole.
5
Start the rotisserie
Check that the fat filter is in place.
Select the FAN GRILL
function.
Set the temperature to 180 oC.
Fig. 24c Position the skewer on the supports
Turn the the rotisserie dial to
.
Rotisserie drive hole
Important!
Always ensure that poultry is cooked thoroughly.
During use, the rotisserie components become
hot. If you leave the oven door open after using
the rotisserie, parts of the control panel may also
become hot. Use oven mitts and take extra care,
especially when removing the rotisserie support
rack from the hot oven.
Always clean the fat filter after every use.
See ‘Care and cleaning’.
Fig. 24d Place the rotisserie in the oven
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Using the electronic timer
You can use the timer at any time, even when
the oven is not in use.
Important!
The timer does NOT turn the oven off.
To set the timer
Fig. 25 Clock display and control buttons
1
2
Press
will start flashing.
Press and
. 0•00 will show and the
symbol
to set the time you want (up to 23 hours
and 59 minutes, in 1-minute steps).
After a few seconds, the clock will show the
time of day within the
symbol steadily lit.
The timer is now counting down.
To check the remaining time
Press
.
To cancel the timer
1
2
Press
Press
.
unitil the time is reset to 0•00.
After a few seconds, the clock will show the time of day
When the set time is up
The timer will beep and the
timer off.
symbol will flash. Press
to stop the beeping and turn the
After a few seconds, the clock will show the time of day.
To adjust the beep volume
Press
to hear the next volume level. The last one selected will be stored.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Automatic cooking
To set the oven for automatic cooking
1
2
Set the oven:
Check the clock shows the correct time (eg 12:07).
Select the function and set the temperature.
The oven will turn on.
Set the cooking time:
Decide how long the food will take to cook, allowing
time for preheating if necessary (eg 40 minutes).
Fig. 26 Clock display and control buttons
Press
Use
.
and
to set the cooking time. AUTO will show in the display.
3 Set the stop time:
Decide when you want your food to be ready by (eg 13:30).
Press
Use
.
and
to set the stop time.
You can turn the oven on manually and set it to turn off automatically by setting the stop time
(step 3 above).
When automatic cooking is set
If there is time before cooking starts, the oven will turn off and the current time of day and AUTO
will show in the clock display, indicating that the oven is set for automatic cooking. Note: the
cooling fan may stay on.
The oven will automatically turn on at the required time (eg 12:50) and turn off at the set stop
time (eg 13:30).
To see the remaining cooking time, press
To see the set stop time, press
.
.
To cancel automatic cooking, press
and turn the function and temperature dials to 0 (off ).
When the stop time is reached
The oven will turn off, the timer will beep and AUTO will flash.
1
2
Press
to stop the beeping and return the oven to manual mode.
Turn the function and temperature dials to 0 (off ).
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Using your gas cooktop
2
3
2
1
1
Fig 27 Cooktop layout
1
2
3
Triple-ring wok burner
Semi-rapid burner
Dual burner
Gas burners
The dial controls the flow of gas through the safety valve.
Semi-rapid and triple-ring wok burners
= closed valve (OFF)
= maximum flow of semi-rapid and triple-ring burner burners
= minimum flow of semi-rapid and triple-ring burner burners
0
You can choose to cook at any heat between
and
, but never
between
and O (OFF).
Dual burner
= closed valve (OFF)
0
= maximum flow of inner crown only (turn dial clockwise)
= minimum flow of inner crown only (turn dial clockwise)
= maximum flow of inner & outer crowns (turn dial anticlockwise)
= minimum flow of inner & crowns (turn dial anticlockwise)
You can choose to cook at any heat between
and , but never between and 0 (OFF) or between
0 (OFF).
and
or between
and
Fig. 28 Burner control dial
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Using your gas cooktop
Before using your cooktop
Before using your new cooktop, please:
Read this user guide, taking special note of the ‘Safety and warnings’ section.
Turn the power to the cooker on at the wall.
Make sure all burner control dials are turned off.
Using the gas burners
1
2
Choose the control dial for the burner you want to use.
Semi-rapid and triple-ring burners: press the dial in gently and turn it anticlockwise to the
position. The ignitors on all the burners will spark.
Dual burner: press the dial in gently and turn it anticlockwise to the
inner and outer crowns) or press the dial it gently and turn it clockwise to the
ignite the inner crown only). The ignitors on all the burners will spark.
position (to ignite the
position (to
Hold in the dial for approximately 10 seconds after the burner has lit. Releasing the dial too soon
will extinguish the flame.
3
Adjust the flame anywhere between
adjust the flame between or
and
or
or
and
or
and
positions. Do not
and 0 (OFF).
Note: If the burner does not light within 15 seconds, turn the control dial off and wait at least
one minute before trying again.
4
5
To turn the burner off, turn the dial clockwise (semi-rapid and triple-ring burners or dual burner
when using both crowns) or anticlockwise (dual burner when using the inner crown only) to 0
(OFF) until you hear the safety click.
After use, always turn the dials to the 0 (OFF) position.
Flame failure safety feature
The flame failure probe cuts off the gas supply to the burner if the flame is blown out.
When lighting the burner on flame failure models, hold down the dial for approximately 10
seconds after the burner has lit. Releasing the dial too soon will extinguish the flame.
If the flames are accidentally extinguished, turn off the burner and do not try to light it again for
at least one minute (to allow the gas to disperse).
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Using your gas cooktop
If a burner does not light
Check that:
The cooker is plugged in and the electricity is switched on.
The gas is turned on.
The gas bottle is not empty (if you are using bottled gas).
You have held down the dial for at least 10 seconds.
The ignitors are sparking. If the ignitors are not sparking, they may be dirty or wet. Clean them
with a toothbrush and methylated spirits, as shown in Fig.31.
Flame failure probe
Ignitor
Fig. 29 Cleaning the probe and ignitor
If the flame is irregular
If the flame is yellow or irregular, check that the burner parts, including the burner cap, are:
clean and dry.
positioned correctly. See ‘Care and cleaning’.
See also ‘Cooktop troubleshooting’.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Using your gas cooktop
Matching cookware to burner
Use flat-bottomed pans, and make sure they match the size of the burner, as shown in the
following table. A small pot on a large burner is not efficient.
Diameters of pans which may be used on the cooktop
Burners
Minimum
16 cm
Maximum
24 cm
Semi-rapid
Triple-ring wok
26 cm
28 cm
Maximum diameter for woks 36 cm
Dual (inner crown only)
12 cm (6 cm with small
14 cm
pan support)
Dual (inner and outer
crowns)
26 cm
28 cm
Maximum diameter for woks 36 cm
Fig. 30 Correct and incorrect
matching of cookware and burner size
Fig. 31 Efficient and inefficient saucepan bottoms
Small pan support
This pan support is to be placed on top of the dual burner when
using small diameter pans, in order to prevent them from tipping
over. Use the burner with the inner crown only.
Fig. 32 Small pan support
Wok stand
The wok stand fits over the triple-ring wok or dual burner trivet.
Important!
Using a wok without the stand may cause the wok to tip or the wok or dual burner to operate
incorrectly.
Do not use the stand for ordinary, flat-bottomed saucepans.
The wok stand MUST BE PLACED ONLY over the trivet for the triple-ring wok or dual burner.
The cooktop becomes very hot during operation. Keep children well out of reach.
WRONG
CORRECT
Fig. 33 Correct placement of wok stand
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Care and cleaning
Important!
Before you start cleaning your cooker, please:
Read these cleaning instructions and the ‘Safety and warnings’ section at the start of this user
guide.
Turn the cooker off at the wall.
Make sure the cooker is a safe temperature to touch.
Do not use a steam cleaner.
Do not keep flammable substances in the oven.
General advice
Wipe down the cooktop and wipe out the oven after every use.
Wipe up spills. Avoid leaving alkaline or acidic substances (such as lemon juice or vinegar) on
the surfaces.
Do not use cleaning products with a chlorine or acidic base.
Cleaning the outside of the cooker
Important!
Do not use abrasive cleaners, cloths or pads on the outside surfaces.
Immediately wipe off any caustic cleaners if they are spilled onto the oven door handle.
Wipe the outside surfaces often, using warm water and a mild household detergent. The
stainless steel may also be cleaned with a suitable cleaner and polish.
Note: if you choose to use a commercial stainless steel cleaner, please read the label to make
sure it does not contain chlorine compounds as these are corrosive and may damage the
appearance of your cooker.
Cleaning the gas cooktop
Maintenance Period
Daily
Description
•
•
Clean gas cooktop as per following instructions.
Remove all burner parts, and clean using a non-abrasive
detergent. Rinse in cold water, dry thoroughly, and replace.
Clean the ignitor carefully, using a toothbrush and
methylated spirits.
Monthly
•
•
Contact your local authorised gas Service Agent to perform
a thorough check on all gas components on the gas
cooker.
Every 3-4 years
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Care and cleaning
Burner parts and trivets
You can remove and clean these parts with hot soapy water or non-abrasive detergents. Clean
spills regularly before they become burnt on. Do not wash these parts in a dishwasher.
After cleaning, check that the burners and their flame spreaders are dry before replacing
correctly.
It is very important to check that the burner flame spreader and the cap have been correctly
positioned. Failure to do so can cause serious problems.
Note: to avoid damage to the electronic ignition, do not try to light a burner without all burner
parts in place.
Replacing the semi-rapid burners
Carefully replace the burner parts as per the following Figs.
Check that:
the ignitor is always clean to ensure trouble-free sparking.
The probe is always clean to ensure correct operation of the safety valves (some models only)
Note: both the ignitor and probe must be very carefully cleaned using a toothbrush and
methylated spirits (see Fig.29).
Cap
Flame
spreader
Probe
Ignitor
Fig. 34 Correct line-up of semi-rapid burner parts
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 35 Replacing the semi-rapid burner caps
32
Care and cleaning
Replacing the triple-ring wok and dual burners
Carefully replace the burner parts as per the following Figs.
Fit the flame spreader to the housing as shown by the arrow in the Figs.36a-36b. Make sure the
burner is not able to rotate (Fig. 37).
Check that:
the ignitor is always clean to ensure trouble-free sparking.
The probe is always clean to ensure correct operation of the safety valves (some models only)
Note: both the ignitor and probe must be very carefully cleaned using a toothbrush and
methylated spirits (see Fig.29).
Ignitor
Ignitor
Probe
Probe
Fig. 36b Correct positioning of
flame spreader - dual burner
Fig. 36a Correct positioning of
flame spreader - triple-ring wok burner
Cap
Ring
Fig. 37 Correct positioning of
Fig. 38 Incorrect and correct positioning
cap and ring - triple-ring wok and dual burner
of cap and ring - triple-ring wok and dual burner
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Care and cleaning
Cleaning the inside of your oven
Do not use abrasive cleaners, cloths or pads to clean the enamel.
To make cleaning easier, you can remove the side racks, the oven door, and the fat filter.
Fig. 39 Removing the side racks
Drop-down grill element
To lower the grill element: use a flat-head screwdriver or a small coin to loosen the element
fixing screws.
When you have finished cleaning the oven ceiling, raise the grill element and screw the element
fixing screws back onto the studs. Make sure that the fixing screws are tightened and the
element is held securely in place.
The grill element itself is self-cleaning.
Fixing screw
Stud
Fig.40 Drop-down grill element
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Care and cleaning
Cleaning the enamel cavity
Clean the enamel on the inside of the oven when it has cooled down, using household
detergents or an ammonia-based cleaner. You may use ‘off the shelf’ oven cleaners, if you
carefully follow the manufacturers’ instructions.
Cleaning the fat filter
Clean the fat filter after every use. If the filter is not
cleaned, it will block and shorten the life of the fan
element. If the filter is lightly soiled, place it in a
dishwasher on normal wash. If the filter is very dirty,
place in a saucepan with either two tablespoons
of clothes washing powder, or one tablespoon of
dishwashing powder. Bring to the boil and leave to soak
for at least 30 minutes. Rinse the filter in clean water and
dry.
Fig. 41 Fat filter
Cleaning the grill tray and shelves
Stop notch
Guard rail
Clean these in hot, soapy water.
After cleaning slide in the shelves, making sure that:
they are between the two wires of a shelf position;
the stop notches point down;
the guard rail is at the back.
Note: the grill tray should be positioned between
the two wires of a shelf position and orientated
as shown.
Stop
notch
Fig. 42 Oven shelves and grill tray
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Care and cleaning
Fitting and removing the sliding shelf supports
When fitting the sliding shelf supports, make sure that you fit:
the side racks first
the slides to the top wire of a shelf position
both sides of each pair of slides
both slides on the same level.
Important!
Remove the side racks first to make removing the sliding shelf supports easier.
1
2
1
Fig. 43a Fitting the sliding shelf supports
Fig. 43b Removing the sliding shelf supports
Download from Www.Somanuals.com. All Manuals Search And Download.
36
Care and cleaning
Storage compartment
The storage compartment is
accessible through the pivoting
panel (Fig.44).
Important!
Do not store flammable material
in the oven or in the storage
compartment.
Pivoting panel
Fig. 44 Storage compartment
Replacing the oven lamp
1
2
3
4
Turn the power to the cooker off at the wall.
Let the oven cavity and the heating elements cool down.
Twist the lamp cover off.
Remove and replace the halogen lamp with a new one suitable for high temperatures (300oC)
with the following specifications: 220-240V, E14 and same wattage as the lamp being replaced
(25W).
Important!
Never replace the bulb with bare hands; contamination from your fingers can cause premature failure.
Always use a clean cloth or gloves.
5
6
Twist the lamp cover back on
Set the clock.
Note: oven bulb replacement is not covered by your warranty.
Left lamp
cover
Left halogen
lamp
Right halogen
lamp
Right lamp
cover
Fig.45 Replacing the oven lamp
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Care and cleaning
Removing and replacing the inner door glass pane for cleaning
If you wish to clean the inner glass of the door, make sure you follow the precautions and
instructions very carefully.
Replacing the glass pane and the door incorrectly may result in damage to the appliance
and may void your warranty.
Important!
Take care, the oven door is heavy. If you have any doubts, do not attempt to remove the
door.
Make sure the oven and all its parts have cooled down. Do not attempt to handle the parts
of a hot oven.
Take extreme care when handling the glass pane. Avoid the edges of the glass bumping
against any surface. This may result in the glass shattering.
CAUTION: Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door
glass since they can scratch the surface, which may result in shattering of the glass.
If you notice any sign of damage on any of the glass panes (such as chipping, or cracks), do
not use the oven. Call your Authorised Service Centre or Customer Care.
Make sure you replace the glass pane correctly. Do not use the oven without glass pane
correctly in place.
If the glass pane feels difficult to remove or replace, do not force it. Call your Authorised
Repairer or Customer Care for help.
Note: service visits providing assistance with using or maintaining the oven are not covered
by your warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Care and cleaning
Removing the oven door
The oven door can easily be removed as
follows:
Open the door to the full extent (fig. 46a).
Open the lever ‘A’ completely on the left and
right hinges (fig. 46b).
Hold the door as shown in fig. 46e.
Gently close the door (fig. 46c) until left and
right hinge levers ‘A’ are hooked to part ‘B’ of
the door (fig. 46b).
Fig.46a
Withdraw the hinge hooks from their location
following arrow ‘C’ (fig. 46d).
A
Rest the door on a soft surface.
B
Fig.46b
Fig.46c
C
Fig.46e
Fig.46d
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Care and cleaning
Removing the inner pane of glass
The oven door is fitted with no. 2 panes:
no. 1 outside;
no. 1 inner.
To clean all panes on both sides it is necessary to remove the inner pane as follows:
Remove the inner glass retainer
1
Remove the oven door and place it on a soft surface.
IMPORTANT: The door shall be placed horizontally as per Fig. 47.
Press down on both tabs to release the glass retainer.
Remove the glass retainer.
2
3
1
2
2
1
Fig.47 Removing the inner
glass retainer
2
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Care and cleaning
Remove the inner glass pane
Lift and remove the inner pane slightly, as shown in the figure 48.
2
1
Fig.48 Removing the inner
glass pane
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Care and cleaning
After cleaning, replace the inner glass pane
When replacing the inner glass pane, make sure that:
You replace the pane correctly, as shown. The pane must be in the position described below in
order to fit into the door and to ensure that the appliance operates safely and correctly.
You take extra care not to bump the edges of the glass against any object or surface.
You do not force the pane into place. If you are experiencing difficulties replacing the pane,
remove it and start the process again from the beginning. If this still does not help, call Customer
Care.
Check that you are holding the pane the correct way. You should be able to read the wording on
it as it faces you.
Check that the gasket ‘A’ is in place (Fig. 49). If not, correctly place the gasket in the top edge of
the inner glass (in the centre).
1
2
Insert the inner glass pane in the uppermost pair of grooves and push it slightly (arrow 1 in
figure 49).
Gently lower into place (arrow 2 in figure 49).
A
2
1
Fig.49 Replace the inner
glass pane
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Care and cleaning
Replace the glass retainer
1
2
Position the glass retainer, as shown in the figure 50. It should sit on the bottom edge of the
outer glass. Check that the clamps ‘M’ are not deformed or damaged.
Gently push the glass retainer back into place. You should be able to hear the tabs on both
sides click as they lock the glass retainer in.
Important!
Make sure the glass retainer is correctly and firmly in place and that the glass pane is secure.
2
Click
M
1
M
1
M
2
Click
Fig.50 Replace the
glass retainer
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Care and cleaning
Refit the door
1
2
Hold the door firmly (fig.51a).
Insert the hinge tongues into the slots, making
sure that the groove drops into place as shown
in the figure 51b.
3
4
Open the door to its full extent.
Fully close the levers ‘A’ on the left and right
hinges, as shown in the figure 51c.
Close the door and check that it is properly in
place.
5
Fig.51a
Fig.51b
A
Fig.51c
Download from Www.Somanuals.com. All Manuals Search And Download.
44
Troubleshooting
Problem
Possible solutions
A burner does not light.
Check the cooker is switched on at the wall.
Check the gas supply valve is turned on and the
supply to the house is working. You should hear the
gas when you turn a burner on.
Check the gas bottle is not empty.
The ignitors may be dirty. Clean them with a
toothbrush and methylated spirits.
The burner parts may not be located properly. Check
the assembly and make sure the burner cap is sitting
flat.
My burner flames are yellow or
hard to start.
The burner parts may not be located properly. Check
the assembly and make sure the burner cap is sitting
flat.
If you use bottled gas, this may indicate you are
getting near the end of the bottle.
Check the burner parts are clean and dry.
The gas pressure may not be at the correct level.
Check with your service person or installer.
Your cooker may not be set up for the gas you are
using. Check this with your service person or installer.
One of my burners has an uneven Check the burner parts are clean and dry. Check the
flame.
assembly and make sure the burner cap is sitting flat.
The flame goes out at low
settings.
The gas supply pressure may be low. Check this with
your service person or installer.
The low setting may have been adjusted incorrectly.
Check this with your service person or installer.
If you use bottled gas, this may indicate you are
getting near the end of the bottle.
My burners do not turn down
much (when running on bottled
gas or LPG).
Your cooktop may not have been adjusted correctly.
Check this with your service person or installer.
The flame tips are very yellow.
Call your service person to service the cooker.
Call your service person to service the cooker.
Call your service person to service the cooker.
There are objectionable odours.
The flame appears to lift off the
burner.
There is an electricity failure.
If there is an electricity failure, you can still use your
cooktop. Light the burners by holding a match close
to the side of the burner and turning the control dial
to the High position. Wait until the flame is burning
evenly before adjusting.
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Warranty and service
Before you call for service or assistance ...
Check the things you can do yourself. Refer to the installation instructions and your user guide
and check that:
1
2
Your product is correctly installed.
You are familiar with its normal operation.
If after checking these points you still need assistance, please refer to the Service & Warranty
book for warranty details and your nearest Authorised Service Centre, or contact us through our
website:
This cooker has been designed and constructed in accordance with the following
codes and specifications:
In New Zealand and Australia:
AGA101 (AS 4551) Approval Requirements for Domestic Gas cooking appliances
AS/NZS 60335-1 General Requirements for Domestic electrical appliances
AS/NZS 60335-2-6 Particular Requirements for Domestic electrical cooking appliances
AS/NZS 1044 Electromagnetic Compatibility Requirements.
Product details
Fisher & Paykel Ltd
Model
Serial No.
Purchaser
Suburb
Date of Purchase
Dealer
Town
Country
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright © Fisher & Paykel 2012. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.
NZ AU
F&P PN - 590434 A F&P ITALY PN - 1103973-ß1
04.2012
Download from Www.Somanuals.com. All Manuals Search And Download.
|