Integrated panel preparation
DS605I and DD605I models
DishDrawer
NZ AU GB IE
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Double models
Product preparation
2
4
Single models
Product preparation
Panel Installation
Badge cut-out, handle and mounting bracket
6
7
8
Securing the mounting brackets
Reconnecting the wires and fitting the
panels and a custom toe kick (double models only)
Important!
SAVE THESE INSTRUCTIONS
The models shown in this User Guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
contact your local Fisher & Paykel dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Product preparation
Double DishDrawer models
A
min.
5 mm
B
C
D
8 mm
Air gap
height of
toe kick
panel
min.
12 mm
Installation diagrams for illustration purposes only
The following calculations assume the top of the upper panel is aligned with the top of the
adjacent cabinetry. The final panel/cabinetry alignment is achieved by adjusting the feet:
width of ALL panels
Measure A (the width between adjacent door/drawer fronts) and write it in the first box below,
then complete the equation.
A
door clearance
(min. 2.5 mm)
width ALL panels
door clearance panel width
A
i.e 600 mm - 2 x 2.5 mm = 595 mm
- 2 x
+
=
=
(min. 595 mm)
height of upper panel
height
height upper panel
B
door extension
standard height
B
upper panel
i.e 398 mm
+
0 mm = 398 mm
398 mm
(0 mm recommended)
(min. 595 mm)
height of lower panel
Measure C (door/drawer height (or equivalent)) and write it in the first box below,
then complete the equation.
height
height
height upper panel
height lower panel
C
C
upper panel
lower panel
i.e 717.5 mm - 398 mm - 8 mm = 311.5 mm
Air gap
-
- 8 mm =
Air gap
(min. 311.5 mm)
(min. 717.5 mm + B)
Note: The ‘door extension’
B
allows for the top of the upper panel to be above the DishDrawer® where required.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Product preparation
Toe kick preparation
height of toe kick panel
Measure D (height from the top of adjacent cabinet door fronts to the floor) and write it in the first
box below, then complete the equation.
height
height
toe kick panel
D
B
D
B
toe kick panel
i.e 817.5 mm - 0 mm - 735 mm - 12 mm = 70.5 mm
-
- 735 mm - 12 mm =
height adjacent
door
DishDrawer®
min. clearance (min. 70.5 mm)
cabinetry
extension
dimension
Toe kick options
The black prefinished toe kick panel is
supplied. This panel can also have a front panel
of your choice attached to it using screws or an
adhesive.
A toe kick panel of any material with thickness
9 - 19 mm can be screwed to the plastic toe
kick mounting bracket (supplied).
432 mm
55 mm
Integrated Panel material
67-127 mm
max.
67 mm
16 -20 mm panel thickness
Adequately sealed to withstand moisture (50OC @ 80% RH)
Parts supplied
Mounting
bracket (2)
Toe kick
mounting
screws (5)
Panel mounting
Integrated rectangular badge (2)
screws (12)
(Satin chrome supplied)
Toe kick mounting
bracket (1)
Integrated door seal (2)
Prefinished Toe kick panel (1)
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Product preparation
Single DishDrawer models
A
min.
5 mm
B
9 mm
Air gap
9 mm
Air gap
Installation diagrams for illustration purposes only
The following calculations assume the top of the panel is aligned with the top of the adjacent
cabinetry:
width of the panel
Measure A (the width between adjacent door/drawer fronts) and write it in the first box below,
then complete the equation.
A
door clearance
(min. 2.5 mm)
panel width
door clearance panel width
A
i.e 600 mm - 2 x 2.5 mm = 595 mm
- 2 x
=
(min. 595 mm)
height of the panel
Measure B (door/drawer height (or equivalent)) and write it in the first box below,
then complete the equation.
B
panel height
panel height
B
i.e 407 mm - 9 mm = 398 mm
Air gap
-
9 mm Air gap
=
(min. 398 mm)
Note: when the top of the DishDrawer® has to be lower than the adjacent cabinetry, the panel can be increased
in height.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Product preparation
.
el
er® near floor lev
w
a
ram if installing the DishDr
se this diag
U
9 mm
Air gap
9 mm
Air gap
Integrated Panel material
16 -20 mm panel thickness
Adequately sealed to withstand moisture (50OC @ 80% RH)
Parts supplied
Panel mounting
screws (6)
Integrated rectangular badge (1)
(Satin chrome supplied)
Mounting
bracket (1)
Integrated door seal (1)
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Badge cut-out, handle and mounting bracket
Installation diagrams feature double models for illustration purposes only
1
Important!
Ensure the product is not plugged in
127 mm
Badge z
o
ne
211 mm
54 mm
127 mm
30 mm
Badge z
25 mm
o
ne
2
3
1
2
1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Securing the mounting brackets
3
1
2
4
2
16 mm x6
1
Double models only:
Important!
Break off the tab at the top
of the Lower Mounting Bracket
3
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Reconnecting the wires and fitting the panels
and a custom toe kick (double models only)
5
2
1
6
Important!
Ensure the rubber seal between the
drawer and panels is kept in place
2
16 mm x 5
1
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright © Fisher & Paykel 2007. All rights reserved.
The product specifications in this booklet apply to
the specific products and models described at the
date of issue. Under our policy of continuous product
improvement, these specifications may change at any
time. You should therefore check with your Dealer to
ensure this booklet correctly describes the product
currently available.
NZ AU GB IE
DishDrawer integrated panel preparation
Published: 06/2007
Part No. 529712 A
Download from Www.Somanuals.com. All Manuals Search And Download.
|