Escient Network Card CH 1 User Manual

Escient Vision  
CH-1 Adapter Kit User’s Guide  
Version: 1.0 September 2008  
Welcome  
CH-1 Kit Components.........................................................................................2  
What You Need to Setup the CH-1 Adapter Kit ................................................3  
CH-1 at a Glance .................................................................................................4  
Component to HDMI Adapter [input side].................................................................4  
Component to HDMI Adapter [output side] ..............................................................4  
Setup  
Connecting the Adapters and Cables ...............................................................5  
Step 1: Power down your Vision ...............................................................................5  
Step 2: Connect the Component to HDMI Adapter ..................................................6  
Step 3: Connect the Keyspan USB to Serial Adapter..............................................6  
Step 4: Configure the Sony Changer’s Back Panel Switches.................................6  
Step 5: Turn on your Vision .......................................................................................6  
Step 6: Lookup Changer Discs..................................................................................6  
Audio Configuration  
Configure the Sony Changer's Digital Audio Settings ....................................6  
Testing the Connection  
Component to HDMI Adapter.............................................................................7  
Keyspan USB to Serial Adapter.........................................................................7  
Trouble Shooting  
Business Hours...................................................................................................8  
After Hours..........................................................................................................8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
What You Need to Setup the CH-1 Adapter Kit  
Vision Series VS or VC client  
A Sony DVP-CX777ES Changer  
Null modem female to female serial cable  
HDMI cable of the appropriate length (not included)  
Important:  
Each Vision VS or VC client supports only one CH1- Adapter kit. If you are  
installing more than one changer you will need to purchase an optional Keyspan  
4 Port USB Serial Adapter and install it in place of the single Keyspan USB to  
Serial adapter that is included in the CH-1 Kit. The 4 port unit retails for about  
$150.00 US.  
If you plan on using one or mote external changers and controlling Vision via RS-  
232 you will also need to purchase the Keyspan 4 port USB adapter. It is always  
preferable to use TCP/IP for eternal control if your control system supports it.  
Keyspan USA49WG  
For more information on the Keyspan USB 4 Port Serial Adapter, please visit the  
Keyspan web site.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CH-1 at a Glance  
Component to HDMI Adapter [input side]  
Component video connectors (Pr Pb Y)  
Input status LED  
Optical Digital Audio Input  
Coax Digital Audio Input  
Component to HDMI Adapter [output side]  
Output Status LED  
HDMI Output  
5 volt DC Power Input  
Test Switch (only present on some older models – not used)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup  
Use the information in this chapter to set up and configure the CH-1 adapter kit  
for use with your Vision system.  
To get started you need to:  
1. Properly configure your Vision VS or VC clients on your Ethernet network.  
2. Properly configure your Sony changer  
Important:  
Read all of the following installation instructions carefully and completely before  
you begin the installation.  
Connecting the Adapters and Cables  
Step 1: Power down your Vision  
Press and hold the power button on the front panel for 5 seconds and then  
release. Wait for the Vision to completely power off at which time the power LED  
will go out. This may take a few seconds to complete.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 2: Connect the Component to HDMI Adapter  
1. Connect the included component video cable and digital audio cable  
between the Sony changer’s outputs and the inputs on the video adapter.  
2. Connect your HDMI cable between the video adapter HDMI output and  
the first HDMI input on the Vision.  
3. Insert the DC side of the power supply into the video adapter.  
4. Insert the AC side of the power supply into the wall outlet.  
Step 3: Connect the Keyspan USB to Serial Adapter  
1. Connect the included USB cable between the top USB port on the rear of  
the Vision and the Keyspan Serial adapter.  
2. Connect a null modem (female to female) RS-232 cable (not included) to  
the DB-9 male connector side on the Keyspan Serial adapter.  
Step 4: Configure the Sony Changer’s Back Panel Switches  
1. Make sure the COMMAND MODE switch is set to 1.  
2. Make sure the COMPONENT VIDEO OUT switch is set to  
PROGRESSIVE.  
Step 5: Turn on your Vision  
Press and release the power button on the front panel of the Vision and wait for it  
too boot up. The boot process is complete when the power LED changes to  
blue.  
Step 6: Lookup Changer Discs  
After Vision is fully running, you can start the disc lookup process. To initiate the  
initial lookup of all of the DVDs in the changer you must open and close the  
changer door using the Sony’s front panel OPEN/CLOSE button. Vision will then  
begin to identify all of the changer discs. This may take up to an hour and a half  
for a full changer.  
Audio Configuration  
Configure the Sony Changer’s Digital Audio Settings  
The Sony DVP-CX777ES changer’s digital audio output must be set to output  
Digital 5.1 and not PCM. Use the Sony remote and on screen menus to change  
the digital audio output setting.  
Follow these steps using the SONY CHANGER REMOTE to set the correct  
audio settings on the changer:  
1. While a movie is playing form the changer press STOP.  
2. Press the DISPLAY key to show the changer’s on screen menu system.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Arrow down to the bottom icon in the list, a red toolbox.  
4. Press ENTER to display the Quick Setup Menu.  
5. Highlight “QUICK” and press ENTER. This will start the Sony DVD  
Player’s Quick Setup feature.  
6. Follow the instructions on-screen.  
7. When you get to the 4th screen, select DIGITAL & 5.1CH OUTPUT” then  
press ENTER.  
8. On the next screen select “DOLBY DIGITAL” then press ENTER.  
9. On the next screen select “DTS” then press ENTER.  
10.Follow the remaining instructions on-screen.  
11.When you complete Quick Setup, you will see the list of icons again.  
Press DISPLAY 2 times to clear the screen.  
Testing the Connections  
You can verify the LED states on each of the adapters to make sure everything is  
properly connected.  
Component to HDMI Adapter  
The LEDs on both sides of the adapter should be blue when playing a movie  
from the changer.  
If the analog (component video) side is off, the component video and digital audio  
connections are not properly connected to the Sony changer or the changer is  
not powered on.  
If the HDMI side is off while you are playing a changer based disc, the HDMI  
cable is not properly connected to the Vision or the adapter. Check the cable.  
If the HDMI side is red, move the small switch on the digital side to the opposite  
position using a paperclip. It should now be blue.  
Keyspan USB to Serial Adapter  
The LED on the USB adapter will be lit when it is connected an active. If it is not  
lit, make sure that the USB cable is properly connected.  
The LED will flash occasionally when there is communication with the changer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble Shooting  
Make sure you have all of the appropriate connections made and that you have  
connected AC power to the adapter, changers, and Vision.  
If you experience any problems connecting a Sony DVP-CX777ES changer to  
Vision, please contact your rep or Escient tech support. Please have your model  
and serial number ready.  
Business Hours  
Phone: 800.372.4368  
Select #3 for a support representative  
8am-6pm (GMT-05:00) Eastern Time  
After Hours  
Phone: 800.372.4368  
Follow prompts for instructions  
6pm-9am (GMT-05:00) Eastern Time  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ei Electronics Universal Remote Ei 411 User Manual
Exide Automobile Battery Charger DEC200 User Manual
Fellowes Mouse 9893501 User Manual
Fiesta Gas Grill EZT40050 B416 User Manual
Fisher Price Battery Charger 74242 User Manual
Fisher Price Motorized Toy Car X3419 User Manual
Five Star Ranges Range PN537 7BW User Manual
GBC Binding Machine 620OS User Manual
GE Washer GCRH410 User Manual
Gitzo Camcorder Accessories GT3540LS User Manual