x7722271404 / x772000164
SRM-225
GRASS TRIMMER /
BRUSH CUTTER
Operator’s Manual
Burn Hazard
The muffler or catalytic muffler and surrounding cover may become extremely hot.
Always keep clear of exhaust and muffler area, otherwise serious personal injury may
occur.
The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Users of this equipment risk injury to themselves and others if the unit is used
improperly and/or safety precautions are not followed. ECHO provides an operator’s
manual and a safety manual. Both must be read and understood for proper and safe
operation. Failure to do so could result in serious injury.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
INTRODUCTION
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and
on-the-job dependability. Read and understand this manual and the SAFETY MANUAL. You will find both
easy to use and full of helpful operating tips and SAFETY messages.
The Operator’s Manual
Keep it in a safe place for future reference. Contains specifications and information for safety, operation,
maintenance, storage and assembly specific to this product.
The Safety Manual
Keep it in a safe place for future reference. Explains possible hazards and the measures you should take to
insure safe operation.
SERVICING INFORMATION
Parts/Serial Number
Genuine ECHO Parts and ECHO REPOWER™ Parts and
Assemblies for your ECHO products are available only from an
Authorized ECHO Dealer. When you do need to buy parts always
have the Model Number and Serial Number of the unit with you. You
can find these numbers on the engine housing. For future
reference, write them in the space provided below.
Model No. _________________ SN. ___________________
Service
Service of this product during the warranty period must be performed by an Authorized ECHO Service
Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your
unit for Warranty service/repairs, proof of purchase is required.
Echo Consumer Product Support
If you require assistance or have questions concerning the application, operation or maintenance of this
product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:30 am to
4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial
number of your unit.
Warranty Registration
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at
product confirms your warranty coverage and provides a direct link between you and ECHO if we find it
necessary to contact you.
X7722271109
3
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SRM-225
Additional or Replacement Manuals
For more information
scan this QR code.
Replacement Operator, Safety Manuals, and Parts Catalogs
or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich,
IL 60047 (800-673-1558). Always check the ECHO Web Site for
updated information.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
SAFETY
Manual Safety Symbols and Important Information
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational
messages preceded by symbols or key words. The following is an explanation of those symbols and key
words and what they mean to you.
The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition
which CAN lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal injury if not avoided.
The enclosed message provides information necessary for the protection of the unit.
Note: This enclosed message provides tips for use, care and maintenance of the unit.
CIRCLE AND SLASH SYMBOL
This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result
in serious or fatal injury.
4
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
SAFETY
International Symbols
Symbol
Description
Symbol
Description
Symbol
Description
Symbol
Description
Carburetor
Adjustment -
High speed
mixture
Warning, See
Operator’s
Manual
DO NOT allow
flames or
sparks near fuel
Ignition
ON / OFF
Wear eye, ear
and head
protection
Carburetor
Adjustment -
Idle speed
DO NOT smoke
near fuel
Primer Bulb
Carburetor
Adjustment -
Low speed
mixture
Choke Control
“Cold Start”
Position(Choke
Closed)
Wear hand
and foot
protection
Choke Control
“Run” Position
(Choke Open)
Emergency
Stop
Keep feet away
from blade
RotatingCutting
Attachment
Safety/Alert
Hot Surface
Fuel and oil
mixture
Keep bystanders and helpers
away 15 m (50 ft.).
AV O ID K ICK OU T.
Keep bystanders at least 15 meters
(50 feet) away.
Thrown
objects
Direction of
blade
Beware Thrown Objects
Wear Eye Protection
X7722271109
5
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SRM-225
Personal Condition and Safety Equipment
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating unit.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Eye protection that meets ANSI Z87.1, CE, or CSA Z94.3 requirements must be worn whenever you operate
the unit.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your grip on the handles. Gloves also reduce the
transmission of machine vibration to your hands.
Breathing Protection
Wear a facemask to protect against dust.
Hearing Protection
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become
entangled in moving parts or surrounding growth.
Wear sturdy work shoes with nonskid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Wear no-slip, heavy duty work gloves.
Keep long hair away from engine and air intake. Retain hair with cap or net.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work
for early morning or late afternoon hours when temperatures are cooler.
6
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
SAFETY
The ignition components of this machine generate an electromagnetic field during operation which
may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with
pacemakers should consult with their physician and the pacemaker manufacturer before operating
this machine. In the absence of such information, ECHO does not recommend the use of ECHO
products by anyone who has a pacemaker.
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon,
which affects the fingers of certain individuals, may be brought
about by exposure to vibration and cold. Exposure to vibration
and cold may cause tingling and burning sensations, followed
by loss of color and numbness in the fingers. The following
precautions are strongly recommended, because the minimum
exposure, which might trigger the ailment, is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands, and wrists.
• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and
also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held
power equipment is not required.
• If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling,
consult your physician before further exposing yourself to cold and vibration.
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the
fingers, hands, arms, and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those
areas. Certain repetitive hand activities may put you at a high
risk for developing a Repetitive Stress Injury (RSI). An extreme
RSI condition is Carpal Tunnel Syndrome (CTS), which could
occur when your wrist swells and squeezes a vital nerve that
runs through the area. Some believe that prolonged exposure to
vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist
position. Also, when grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive movement.
• Do exercise to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in
the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve
and muscle damage can be prevented.
X7722271109
7
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SRM-225
All over head electrical conductors and communications wires can have electricity flow with high
voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly,
otherwise serious injury or death may result.
Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains
poisonous emissions and can cause serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator’s Manual
and Safety Manual for instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children
and animals prevented from coming nearer than 15 m (50 ft.)
while the unit is in use.
Keep a Firm Grip
• Always hold throttle handle and support handle with thumbs
and fingers tightly encircling the handles.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on
slippery, uneven or unstable surfaces. Do not work in odd
positions or on ladders. Do not over reach.
Avoid Hot Surfaces
For more information
• Keep exhaust area clear of flammable debris. Avoid contact
scan this QR code.
during and immediately after operation.
Equipment
Use only ECHO approved attachments. Serious injury may result from the use of a non-approved
attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices,
attachments or accessories which have not been tested and approved by ECHO. Read and comply
with all safety instructions listed in this manual and safety manual.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.
• Inspect shield for damage and ensure that the cut-off knife is securely in place. Replace if either is
damaged or missing.
• Check that the cutting attachment is firmly attached and in safe operating condition.
8
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
EMISSION CONTROL (EXHAUST & EVAPORATIVE)
• Check that handle and harness (if included) are adjusted for safe, comfortable operation. See Assembly
Section for proper adjustment.
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a
complete stop before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to
unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible
through openings.
Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or
leaks are found, do not use unit, otherwise serious personal injury or property damage may occur.
Have unit repaired by an authorized servicing dealer before using.
EMISSION CONTROL (EXHAUST & EVAPORATIVE)
EPA 2010 and Later and/or C.A.R.B. TIER III
The emission control system for the engine is EM (engine modification)
and, if the second to last character of the Engine Family on the Emission
Control Information label (sample below) is “C”, “K”, or “T”, the emission
control system is EM and TWC (3-way catalyst). The fuel tank/fuel line
emission control system is EVAP (evaporative emissions). Evaporative
emissions for California models are only applicable to fuel tanks.
An Emission Control Label is located on the engine. (This is an
EXAMPLE ONLY, information on label varies by engine FAMILY).
Product Emission Durability (Emission Compliance Period)
The 50 or 300 hour emission compliance period is the time span
selected by the manufacturer certifying the engine emissions output
meets applicable emissions regulations, provided that approved
maintenance procedures are followed as listed in the Maintenance Section of this manual.
X7722271109
9
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
SRM-225
DESCRIPTION
Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow
the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See
PARTS ORDERING instructions for specific information.
12
11
19
13
18
14
17
15
16
6
5
4
1
3
2
7
8
9
10
Shaft Label
Hot Label
10
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
DESCRIPTION
1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter.
2. THROTTLE HANDLE - FOR RIGHT HAND - Contains Stop Switch, Throttle Lockout, and Throttle
Trigger.
3. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle
trigger is prevented unless throttle trigger lockout lever is engaged.
4. STOP SWITCH - "SLIDE SWITCH" mounted on top of the Throttle Handle. Move switch FORWARD to
RUN, BACK to STOP.
5. SUPPORT HANDLE - FOR LEFT HAND - The support handle is factory assembled to the Drive Shaft
assembly but must be re-positioned for proper cutting attitude and operator comfort.
6. DRIVE SHAFT ASSEMBLY - Includes the Throttle Handle, Gear Housing assembly, Support Handle,
Drive Shaft and Safety Decal.
7. NYLON CUTTER HEAD - Contains replaceable nylon trimming line that advances when the trimmer
head is tapped against the ground while the head is turning at normal operating speed.
8. CUT-OFF KNIFE - Automatically trims line to the correct length: 5" after head is tapped on the ground. If
trimmer is operated without a cut-off knife, the line will become too long, the engine will overheat, and
engine damage may occur.
9. PLASTIC DEBRIS SHIELD ASSEMBLY - Included in plastic bag (co-pack). MUST be installed on unit
before use, see Assembly Instructions. Shield assembly includes the Cut-Off Knife. Mounts on the Gear
Housing Assembly just above the cutting attachment. Helps protect the operator by deflecting debris
produced during the trimming operation. This shield must be replaced with the steel shield for blade use.
10. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press
trigger gradually for best operating technique.
11. SPARK PLUG - Provides spark to ignite fuel mixture.
12. ARM REST - Provides arm rest during operation and protects arm from the hot engine.
13. RECOIL STARTER HANDLE - Pull handle slowly until starter engages, then quickly and firmly. When
engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.
14. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALYST -The muffler or
catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing
particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris.
15. FUEL TANK - Contains fuel and fuel filter.
16. FUEL TANK CAP - Covers and seals fuel tank opening.
17. CHOKE - The choke control is located at the rear of the air cleaner housing. Move choke lever to Cold
Start (
) to close choke for cold start. Move choke lever to “Run” (
) position to open choke.
18. AIR CLEANER - Contains replaceable filter element.
19. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging
air from the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return
line. Pump purge bulb an additional 4 or 5 times.
X7722271109
11
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
SRM-225
CONTENTS
The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging
restrictions, shield installation and other assembly may be necessary.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or
missing parts. Use the contents list to check for missing parts.
*Some Echo units may be factory pre-assembled. The nylon line head, plastic debris shield, and mounting
hardware shown in the contents list are pre-assembled to the unit. Assembly tools are not supplied with
these units. The front handle may need to be re-positioned for comfortable operation.
____ - 1 - Power Head / Drive Shaft Assembly
____ - 1, Operator’s Manual
____ - 1, Safety Manual
____ - 1, Emission Control Warranty Statement
____ - 1, Warranty Registration Card
____ - 1, Safety Glasses
____ - 1, Echo Power Blend XTM 2-Stroke Oil Sample
*____ - 1, Nylon Trimmer Head
*____ - Assembly Tool(s)
*____ - 1, Plastic Shield
*____ - 1, Shield Plate
*____ - 3, 5mm x 16mm Screws (shield mount)
12
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
ASSEMBLY
ASSEMBLY
Plastic Shield Installation
(Nylon line operation)
Parts Required:
Plastic Debris Shield, Shield Plate,
three (3) 5 x 16 mm screws.
The plastic shield is for use with the Nylon Line Head only. Install Metal Shield when using plastic or
metal blades, or serious injury may result.
1. Remove plastic threaded shaft sleeve and adapter plate (C)
from PTO shaft (A).
2. Place the shield on the bottom of the bearing housing
flange.
3. Place shield plate (B) on shield, align holes. Install three (3)
A
B
screws from bottom through plate and shield into gear case.
4. Assemble adapter plate (C) onto PTO shaft.
C
Nylon Line Head Installation
D
Parts Required: Nylon Line Head.
A
Wear Gloves or personal injury may result:
• Cutoff knife is sharp.
C
• Gearcase and surrounding area may be hot.
1. Be sure adapter plate (C) remains on PTO shaft (A).
2. Align locking hole in upper plate with notch in edge of gear housing and insert head locking tool (D).
3. Thread line head (E) onto shaft by turning it
D
counter-clockwise until head is tight against adapter plate
(C).
4. Remove locking tool (D).
E
Semi-automatic nylon line heads must be used only with plastic
debris shield with cut-off knife. Using nylon line heads with
metal debris shield can result in trimmer damage, caused by
operation with excessive line length.
Note: Your nylon line head may appear different than nylon line head shown.
X7722271109
13
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
SRM-225
To Advance Trimmer Line
See Maintenance Section for nylon line replacement.
Note: To advance trimmer line, tap trimmer head against the ground while the head is turning at normal
operating speed.
Remove Nylon Line Head
Note: Do not disassemble nylon line head.
D
1. Align locking hole in upper plate with notch in edge of gear
housing and insert head locking tool (D).
2. Remove line head (E) by turning it clockwise until head is
completely off of shaft.
E
3. Remove locking tool (D).
Support Handle Installation
Note: Label shows minimum spacing for support handle
location
1. Position support handle for comfortable operation and
secure screws.
MIN
SPACING
14
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
OPERATION
OPERATION
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause
unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit
so that exhaust is directed away from your face and body.
Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark
arrestor to prevent discharge of hot particles from the engine. Metal cutters can also create sparks if
the cutter strikes rocks, metal, or other hard objects. Contact local fire authorities for laws or
regulations regarding fire prevention requirements.
Operation With Blades
Blade use DEMANDS specific Brush Cutter configuration. Operation without specified shield, barrier
bar or U-handle, and harness can result in serious personal injury. Follow installation instructions.
TO USE
THESE
BLADES
Pro Maxi-Cut
Grass/Weed
Blade
Rigid Plastic
Tri-Cut
Grass/Weed Blade
Metal Blade
Support Handle, w/or
w/o Barrier Bar
U-Handle or Support
Handle
U-Handle or Support
Handle
w/Barrier Bar
w/Barrier Bar
Plastic Shield
Harness
Plastic Shield
Harness
Metal Shield
Harness
You
must
install
these
parts!
Upper Plate &
Flat Washer
Upper Plate
& Glide Cup
Upper/Lower
Blade Plates
Hex Nut
Hex Nut
Hex Nut
New Cotter Pin
New Cotter Pin
New Cotter Pin
DO NOT INSTALL BLADES ON GT (CURVED SHAFT) MODEL TRIMMERS.
• Arbor Diameter of Upper Blade Plate must match arbor diameter of blades.
• New cotter pin required each time blade is installed.
• Brush cutters over 16.5 lbs (7.5 kg) dry weight (weight w/o fuel) require a double shoulder harness.
X7722271109
15
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SRM-225
Note: The Barrier Bar is used to restrict rearward movement of the unit. The Barrier Bar is NOT A HANDLE
and should not be gripped when using or carrying the unit.
Blade Selection
The type of Blade used MUST be matched to the type and size of material cut. An improper or dull
blade can cause serious personal injury. Blades MUST be sharp. Dull blades increase the chance of
kick-out and injury to yourself and bystanders.
Plastic/Nylon Grass/Weed Blades may be used where ever
the nylon line head is used. DO NOT use this blade for heavy
weeds or brush!
8 Tooth Weed/Grass Blade is designed for grass, garden
debris and thick weeds up to 19 mm (3/4”) diameter. DO NOT
use this blade for brush or heavy woody growth.
80 Tooth Brush Blade is designed for cutting brush and woody
growth up to 13 mm (1/2 in.) diameter.
22 Tooth Clearing Blade is designed for dense thickets and
saplings up to 64 mm (2-1/2 in.) diameter.
Use Shoulder/Waist Harness Use of the Shoulder/Waist
Harness is recommended for ALL Trimmer/Brush Cutter use,
not just Blade operation. The Shoulder/Waist Harness when
used in a trimming operation with nylon line head suspends the
trimmer from the operator's shoulder and reduces operator
fatigue.
During blade operation, the same fatigue reduction is achieved.
Safety to the operator is also enhanced by reducing the
possibility of blade contact with the operator's hands and feet by
restricting trimmer movement.
16
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
OPERATION
For more information
scan this QR code.
Fuel
Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO
requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels
may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended
machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may
also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may
contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing
methanol (wood alcohol) is NOT approved. ECHO brand Power Fuel™ is 93 octane, ethanol-free fuel
premixed with ECHO Red Armor® engine oil at 50:1 ratio. Use of ECHO Power Fuel™ is recommended to
extend engine life in all air-cooled 2-stroke and 2/4-stroke hybrid engines.
Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FD Standards
must be used. Echo brand premium Power Blend X™ Universal 2-Stroke Oil meets these standards. Engine
problems due to inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and
J.A.S.O. FD certified oil, such as Echo premium Power Blend X™, will void the two-stroke engine warranty.
Echo premium Power Blend X™ Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo
engines sold in the past regardless of ratio specified in those manuals.
Handling Fuel
Fuel is VERY flammable. Use extreme care when mixing, storing or handling, or serious personal
injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to
equalize.
• NEVER refuel a unit when the engine is HOT or RUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.
• DO NOT overfill fuel tank. Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after refueling.
X7722271109
17
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SRM-225
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is
repaired.
• Move at least 3m (10 ft.) from refueling location before starting the engine.
Mixing Instructions
1. Fill an approved fuel container with half of the required
amount of gasoline.
2. Add the proper amount of 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Add remaining gasoline, close fuel container, and remix.
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers
to reduce fuel spillage.
For more information
scan this QR code.
After use
• DO NOT store a unit with fuel in its tank. Leaks can occur.
Return unused fuel to an approved fuel storage container.
Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area.
As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building,
away from sparks and flames.
Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a
fuel stabilizer is added.
Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use.
Starting Cold Engine
A
The attachment will operate immediately when the engine
starts, and could result in possible serious injury. Keep
movable parts of the attachment away from objects that
could become entangled or thrown, and surfaces that
could cause loss of control.
1. Stop Switch
Move stop switch button (A) forward, away from the STOP
position.
2. Choke
18
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
OPERATION
Move choke lever (B) to Cold Start Position (
3. Purge Bulb
).
Pump purge bulb (C) until fuel is visible and flows freely in the
clear fuel tank return line. Pump bulb an additional 4 or 5
times.
B
4. Recoil Starter
Lay the unit on a flat area and keep movable attachment parts
clear of all obstacles. Firmly grasp throttle handle and throttle
trigger lockout with left hand and fully depress throttle trigger
to wide open position. Rapidly pull recoil starter handle/rope
(D) until engine fires (or maximum five [5] pulls).
C
5. Choke
After engine fires (or 5 pulls), move choke (B) to the Run
(
)(open)position. Firmlygraspthrottlehandleandthrottle
trigger lockout with left hand and fully depress throttle trigger
to wide open position. Pull starter handle/rope until engine
startsandruns. Releasethrottletriggerandallowunittowarm
up at idle for several minutes.
Note: If engine does not start with choke in “Run” position after
5 pulls, repeat instructions 2 - 5.
D
6. Throttle Trigger
After engine warm-up, grip throttle handle and support handle. Depress the throttle trigger lockout, and
gradually depress throttle trigger to increase engine RPM to operating speed.
Starting Warm Engine
A
The starting procedure is the same as Cold Start except DO
NOT close the choke, and do not hold throttle trigger fully
depressed.
The attachment should not move at idle, otherwise serious
personal injury may result.
Note: If attachment moves, readjust carburetor according to
“Carburetor Adjustment” instructions in this manual or
see your ECHO Dealer.
1. Stop Switch
X7722271109
19
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SRM-225
Move stop switch button (A) forward away from the STOP
position.
2. Purge Bulb
Pump purge bulb (C) until fuel is visible in the “Clear” fuel
return line. Pump bulb an additional 4 or 5 times.
C
3. Recoil Starter
Lay the unit on a flat area and keep movable attachment parts
clear of all obstacles. Firmly grip throttle handle and throttle
trigger lockout with left hand. Rapidly pull recoil starter
handle/rope (D) until engine fires.
Note: If engine does not start after 5 pulls, use Cold Start
Procedure.
D
Stopping Engine
A
1. Throttle
Release throttle trigger and allow engine to return to idle
before shutting off engine.
2. Stop Switch
Move stop switch button (A) backward to STOP position.
If engine does not stop when stop switch is moved to STOP
position, close choke - COLD START position - to stall
engine. Have your ECHO dealer repair stop switch before using unit again.
20
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
MAINTENANCE
MAINTENANCE
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and
hot surfaces.
Your ECHO unit is designed to provide many hours of trouble free service. Regular scheduled maintenance
will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may
want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to
DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is
not listed, see your ECHO Dealer for repairs.
Skill Levels
Level 1 = Easy to do. Common tools may be required.
Level 2 = Moderate difficulty. Some specialized tools may be required.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.
Maintenance Intervals
DAILY
REQ’D
MAINTENANCE
PROCEDURE
OR
EVERY
3
COMPONENT/SYSTEM
SKILL
YEARLY
BEFORE REFUEL MONTHS
USE
LEVEL
Air Filter
Inspect/Clean
1
1
1
1
1
1
2
2
2
I / C *
I / C
R *
Choke Shutter
Fuel Filter
Inspect/Clean
Inspect/Replace
Inspect/Replace
Inspect/Replace
Inspect/Clean
I *
I *
I / R *
R *
Fuel Cap Gasket
Fuel System
I (3) *
I / C
I (3) *
Spark Plug
I / C / R *
Cooling System
Muffler Spark Arrestor
Cylinder Exhaust Port
Inspect/Clean
Inspect/Clean/Replace
Inspect/Clean/Decarbon
I / C / R *
I / C
Drive Shaft
Grease
2
I (1)
I (2)
(Flex Cable Models)
Gear Housing
Grease
2
1
1
Recoil Starter Rope
Screws/Nuts/Bolts
Inspect/Clean
I / C *
I *
Inspect/Tighten/Replace
MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN
IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine
the frequency of required maintenance.
MAINTENANCE PROCEDURE NOTES:
(1) Apply POWER BLENDXTM grease every 25 hours of use.
X7722271109
21
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SRM-225
(2) Apply POWER BLENDXTM grease every 50 hours of use.
(3) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.
* Replacement is recommended based on the finding of damage or wear during inspection.
Air Filter
Level 1.
REPOWERTM AIR & FUEL FILTER KIT.
Parts Required:
1. Close choke (Cold Start Position [
]). This prevents dirt
from entering the carburetor throat when the air filter is
removed. Brush accumulated dirt from air cleaner area.
2. Remove air filter cover. Brush dirt from inside cover.
3. Replace filter if it is damaged, fuel soaked, very dirty, or the
rubber sealing edges are deformed.
• Lightly brush debris from filter.
• Soak heavily soiled filters in water/detergent solution to loosen dirt, then brush lightly.
• Rinse with clean water and allow to dry completely before reuse.
4. Install air filter in air filter case.
5. Install air filter cover.
Fuel Filter
Level 1.
REPOWERTM AIR & FUEL FILTER KIT.
Parts Required:
Fuel is VERY flammable. Use extreme care when mixing,
storing or handling, or serious personal injury may result.
1. Use a clean rag to remove loose dirt from around fuel cap
and empty fuel tank.
2. Use a hook to pull the fuel line and filter from the tank.
3. Remove the filter from the line and install the new filter.
Note: Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for
sale in the United States to be equipped with a special low permeation fuel supply hose between the
carburetor and fuel tank. When servicing model year 2012 and later equipment, only fuel supply
hoses certified by EPA can be used to replace the original equipment supply hose. Fines up to
$37,500 may be enforced for using an un-certified replacement part.
22
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
MAINTENANCE
Spark Plug
Level 2.
REPOWERTM Tune-Up Kit
Parts Required:
.65 mm (.026 in.)
Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada)
otherwise severe engine damage may occur.
1. Remove spark plug and check for fouling, worn and rounded center electrode.
2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage
engine.
3. Adjust spark plug gap by bending outer electrode.
4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).
Cooling System
Level 2.
Parts Required: None if you are careful.
To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area.
This flow of air carries combustion heat away from the engine.
Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from reaching
the cylinder.
• Dust and grass build up on the outside of the cylinder. This
build up insulates the engine and prevents the heat from
leaving.
Removal of cooling passage blockages or cleaning of cooling
fins is considered “Normal Maintenance.” Any failure attributed
to lack of maintenance is not warranted.
1. Remove spark plug lead.
X7722271109
23
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SRM-225
2. Remove air cleaner cover (A).
3. Remove engine cover (B).
B
A
DO NOT use a metal scraper to remove dirt from the cylinder fins.
4. Use brush to remove dirt from the cylinder fins.
5. Remove ignition wires from clip for cleaning.
6. Remove grass and leaves from the grid between the recoil
starter and fuel tank.
7. Assemble components in reverse order.
Exhaust System
Spark Arrestor Screen
Level 2.
F
Parts Required: Spark Arrestor Screen, Gasket
1. Remove engine cover (B).
E
D
2. Place piston at Top Dead Center (TDC) to prevent
carbon/dirt from entering cylinder.
C
3. Remove spark arrestor screen cover (C), gaskets (D), (E),
and screen (F), from muffler body.
4. Clean carbon deposits from muffler components.
Note: When cleaning carbon deposit, be careful not to damage the catalytic element inside muffler.
5. Replace screen if it is cracked, plugged, or has holes burned through.
6. Assemble components in reverse order.
24
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
MAINTENANCE
Exhaust Port Cleaning
Level 2.
B
A
Parts Required: As needed: Heat Shield
1. Remove spark plug lead from spark plug, and remove
engine cover.
2. Place piston at top dead center. Remove muffler (A) and
heat shield (B).
3. Use a wood or plastic scraping tool to clean deposits from
cylinder exhaust port.
Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when
cleaning the exhaust port. Do not allow carbon particles to enter the cylinder.
4. Inspect heat shield, and replace if damaged.
5. Install heat shield and muffler.
6. Tighten muffler mounting bolts (or nuts) to 80-95 in•lbf
(90-110 kgf•cm).
7. Install engine cover and attach spark plug lead.
8. Start engine, and warm to operating temperature.
9. Stop engine, and re-tighten mounting bolts (or nuts) to
specifications.
Carburetor Adjustment
Level 2.
Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor
adjustments can be made. During the break-in period your engine performance will increase and exhaust
emissions will stabilize. Idle speed can be adjusted as required.
High Altitude Operation
This engine has been factory adjusted to maintain satisfactory starting, emission, and durability
performance up to 1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and
emission compliance above 1,100 feet ASL the carburetor may need to be adjusted by an authorized ECHO
service dealer.
If the engine is adjusted for operation above 1,100 feet ASL, the carburetor must be re-adjusted when
operating the engine below 1,100 feet ASL, otherwise severe engine damage may result.
Parts
None
Required:
X7722271109
25
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SRM-225
Note: Every unit is run at the factory and the carburetor is set in compliance with emission regulations.
Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer.
1. Check idle speed and reset if necessary. If a tachometer is
available, idle speed screw (A) should be set to the
specifications found on “Specifications” page of this manual.
A
Turn idle screw (A) clockwise to increase idle speed; counter
clockwise to decrease idle speed.
When carburetor adjustment is completed, the cutting
attachment should not move at idle, otherwise serious
personal injury may result.
Lubrication
Level 1.
POWER BLENDXTM 8 oz. or Lithium Base
Grease.
Parts
Required:
Gear Housing
B
1. Clean all loose debris from gear case.
2. Remove plug (A) and check level of grease.
3. Add grease if necessary. DO NOT over-fill.
C
A
D
Drive Shaft (flex cable models)
1. Loosen two (2) screws (B) and remove center locating screw (C). Pull gear case and shield from drive
shaft housing.
2. Pull flexible cable from the drive shaft housing, wipe clean and re-coat with a thin coating [15 ml (1/2 oz.)]
of grease.
3. Slide the flexible cable back in the drive housing. DO NOT get dirt on the flex cable.
4. Install the gear housing and shield assembly.
Flat edge of washers (D) must be against drive shaft.
26
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
MAINTENANCE
Nylon Line Head Disassembly Instructions
A
Note: For normal use, Speed Feed® head disassembly is not
necessary. However, if circumstances require
disassembly, follow these instructions.
B
1. Press top of locking tabs (A) on both sides of Speed
Feed® head to release cover (B) from eyelet carrier(C).
C
2. Remove cover from eyelet carrier.
Nylon Line Replacement
For more information
scan this QR code.
Wear Gloves or personal injury may result:
• Cutoff knife is sharp.
• Gearcase and surrounding area may be hot.
1. Cut one piece of line to recommended length.
.080 (2.0 mm) dia. – 20’ (6 m)
.095 (2.4 mm) dia. – 20’ (6 m)
2. Align arrows on top of knob with openings in eyelets.
3. Insert one end of trimmer line into an eyelet, and push line
equal distance through trimmer head.
4. Hold trimmer head while turning knob clockwise to wind line
onto spool until about 5” (13 cm) of each line remains
exposed.
Trimmer head is now fully loaded and ready for operation.
X7722271109
27
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SRM-225
When the wear indicators located at the bottom of the
Speed-Feed® head are worn smooth, or if holes appear,
replacement of the cover or the entire Speed-Feed® head is
required.
Wear Indicators
Sharpening Metal Blades
Three styles of metal blades are approved for use on the ECHO
Brush Cutter. The 8-tooth blade can be sharpened during
normal maintenance. The clearing blade and 80 tooth blade
require professional service.
Before sharpening, CLOSELY inspect blade for cracks (look at
the bottom of each tooth and the center mounting hole closely),
missing teeth and bending. If ANY of these problems are
discovered, replace the blade.
When sharpening a blade, always remove the same amount of
materials from each tooth to maintain balance. A blade that is not balanced will cause unsafe handling due
to vibration and can result in blade failure.
1. File each tooth at a 30 degree angle a specific number of
times, eg. 4 strokes per tooth. Work your way around the
blade until all teeth are sharp.
2. DO NOT file the ‘gullet’ (radius) of the tooth with the flat file.
The radius must remain. A sharp corner will lead to a crack
and blade failure.
If an electric grinder is used, use care not to overheat teeth, do
not allow tips/tooth to glow red or turn blue. DO NOT place
blade in cooling water. This will change the temper of the blade and could result in blade failure.
28
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
MAINTENANCE
3. After sharpening teeth, check each tooth radius for evidence
of a square (sharp) corner. Use the round (rat tail) file to
renew the radius.
X7722271109
29
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SRM-225
TROUBLESHOOTING
ENGINE PROBLEM TROUBLESHOOTING CHART
Problem
Check
Status
Cause
Remedy
Fuel strainer clogged
Fuel line clogged
Carburetor
Clean or replace
Clean or replace
See your Echo dealer
Fuel at carburetor No fuel at carburetor
No fuel at cylinder
Carburetor
See your Echo dealer
Open choke
Fuel at cylinder
Clean/replace air filter
Adjust carburetor
See your Echo dealer
Muffler wet with fuel
Fuel Mixture too rich
Enginecranks-
starts hard/
doesn’t start
Stop switch off
Electrical problem
Interlock switch
Turn switch to ON
See your Echo dealer
See your Echo dealer
Spark at end of
No spark
plug wire
Spark gap incorrect
Covered with carbon
Fouled with fuel
Plug defective
Adjust to .65mm (0.026 in.)
Clean or replace
Clean or replace
Replace plug
Spark at plug
No spark
Air filter
Air filter dirty
Normal wear
Clean or replace
Contaminants/residues
in fuel
Fuel filter
Fuel filter dirty
Replace
Contaminants/residues
in fuel
Engine runs,
but dies or
does not
accelerate
properly
Fuel vent
Fuel vent plugged
Clean or replace
Spark Plug
Carburetor
Plug dirty/worn
Normal wear
Vibration
Clean and adjust or replace
Adjust
Improper adjustment
Cooling system
dirty/plugged
Extended operation in
dirty/dusty locations
Cooling System
Clean
Spark Arrestor
Screen
Spark arrestor screen
plugged
Normal wear
Replace
Engine does
not crank
N/A
N/A
Internal engine problem See your Echo dealer
Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition
spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may
result.
30
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
STORAGE
STORAGE
During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep
exhaust area clear of flammable debris during transportation or when storing, otherwise serious
property damage or personal injury may result.
Long Term Storage (Over 30 Days)
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective
storage maintenance which includes the following:
1. Store unit in a dry, dust free place, out of the reach of children.
Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.
2. Place the stop switch in the “OFF” position.
3. Remove accumulation of grease, oil, dirt and debris from exterior of unit.
4. Perform all periodic lubrication and services that are required.
5. Tighten all the screws and nuts.
6. Drain fuel tank completely. Press purge bulb 6-7 times to remove remaining fuel from carburetor then
drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel.
7.
a. Allow engine to cool then remove the spark plug and pour 7 cc (1/4 oz.) of fresh, clean, two-stroke
engine oil into the cylinder through the spark plug hole.
b. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine.
c. Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston
reaches the top of its travel and leave it there.
8. Install the spark plug (do not connect ignition cable).
X7722271109
31
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SRM-225
SPECIFICATIONS
MODEL
SRM-225
Length w/o cutter head
Width
1793 mm (70.6 in.)
251 mm (9.88 in.)
Height
328 mm (12.9 in.)
Weight (dry) w/o cutter head
Engine Type
Bore
5.5 kg (12.1 lb.)
Air cooled, two-stroke, single cylinder gasoline engine
32.2 mm (1.27 in.)
Stroke
26.0 mm (1.02 in.)
Displacement
Exhaust
21.2 cc (1.29 cu. in.)
Spark arrestor muffler or spark arrestor muffler with catalyst
Diaphragm w/purge pump
Carburetor
Ignition System
Spark Plug
Fuel
Flywheel magneto, capacitor discharge ignition type
NGK BPM-8Y (Gap 0.65 mm (0.026 in.)
Mixed (Gasoline and Two-stroke Oil)
50 : 1 Power Blend XTM ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345- FD, two-stroke,
air-cooled engine oil.
Fuel/Oil Ratio
Gasoline
Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10% ethyl
alcohol or 15% MTBE. Do not use alternative fuels such as E-15 or E-85.
Oil
Power Blend XTM Premium Universal 2-Stroke Oil
Fuel Tank Capacity
Starter System
Clutch
0.44 lit. (14.9 US fl. oz.)
Automatic Rewind Starter
Centrifugal Type
Vibration Isolated System
Operating Rod
Drive Shaft
Rubber cushion on engine mount (heavy duty). Rubber grip on front handle.
25.0 mm aluminum Tube
6.35 mm (1/4 in.) flexible shaft
1.4:1 Reduction
Gear Case Ratio
Rotating Direction
Cutter Head
Counter Clockwise; viewed from top
Speed Feed® 400 LH Nylon line head, Line capacity 6.0 m (20 ft.)
Front - loop, Rear handle (w/o rubber)
Optional
Handle
Shoulder Harness
Idle Speed
2,750 RPM
Clutch Engagement Speed
3,850 RPM
Wide Open Throttle Speed (W.O.T.) 8,150 RPM
32
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
WARRANTY STATEMENTS
WARRANTY STATEMENTS
ECHO LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO'S RESPONSIBILITY
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED
WARRANTY IS ONLYAPPLICABLE TO ECHO PRODUCTS SOLD BYAUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COMꢀꢁꢂꢀꢃꢄꢀꢅꢆꢆ-
ꢇꢈꢉꢀꢁꢊꢋꢀꢋꢌꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢂꢍꢉꢇꢐꢋꢂꢏꢋꢇꢁꢈꢀꢑꢏꢂꢒꢀꢐꢊꢓꢓꢆꢇꢍꢒꢀꢎꢇꢋꢌꢀꢄꢁꢊꢂꢀꢊꢈꢇꢋꢔꢀꢕꢍꢉꢇꢐꢋꢍꢂꢇꢈꢉꢀꢄꢁꢊꢂꢀꢓꢂꢁꢒꢊꢑꢋꢀꢑꢁꢈꢅꢂꢖꢐꢀꢄꢁꢊꢂꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢑꢁꢗꢍꢂꢏꢉꢍꢀꢏꢈꢒꢀꢓꢂꢁꢗꢇꢒꢍꢐꢀꢏꢀꢒꢇꢂꢍꢑꢋꢀ
ꢆꢇꢈꢘꢀꢇꢙꢀꢎꢍꢀꢅꢈꢒꢀꢇꢋꢀꢈꢍꢑꢍꢐꢐꢏꢂꢄꢀꢋꢁꢀꢑꢁꢈꢋꢏꢑꢋꢀꢄꢁꢊꢔ
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the
ꢁꢓꢍꢂꢏꢋꢁꢂꢝꢐꢀꢖꢏꢈꢊꢏꢆꢔꢀꢚꢌꢁꢊꢆꢒꢀꢏꢀꢓꢂꢁꢒꢊꢑꢋꢀꢒꢇꢙꢅꢑꢊꢆꢋꢄꢀꢁꢑꢑꢊꢂꢛꢀꢄꢁꢊꢀꢖꢊꢐꢋꢛꢀꢏꢋꢀꢄꢁꢊꢂꢀꢍꢜꢓꢍꢈꢐꢍꢛꢀꢒꢍꢆꢇꢗꢍꢂꢀꢁꢂꢀꢐꢌꢇꢓꢀꢄꢁꢊꢂꢀ!"#$ꢀꢊꢈꢇꢋꢀꢋꢁꢀꢏꢈꢀꢏꢊꢋꢌꢁꢂꢇ%ꢍꢒꢀ!"#$ꢀꢐꢍꢂꢗꢇꢑꢇꢈꢉꢀ
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.
PRODUCT WARRANTY PERIOD
RESIDENTIAL APPLICATION
#ꢀꢀ 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for [ꢀꢁ ꢂꢃꢄꢅꢆꢁꢇꢈꢉ from
date of purchase.
EXCEPTIONS:
#ꢀ 'ꢁꢂꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢍꢈꢉꢇꢈꢍꢀꢓꢁꢎꢍꢂꢍꢒꢀꢓꢂꢁꢒꢊꢑꢋꢐꢛꢀꢋꢌꢍꢀꢍꢆꢍꢑꢋꢂꢁꢈꢇꢑꢀꢇꢉꢈꢇꢋꢇꢁꢈꢀꢖꢁꢒꢊꢆꢍꢛꢀ\ꢍꢜꢇꢃꢆꢍꢀꢒꢂꢇꢗꢍꢀꢑꢏꢃꢆꢍꢐꢛꢀꢚꢕ/ꢀꢐꢁꢆꢇꢒꢀꢒꢂꢇꢗꢍꢀꢐꢌꢏꢙꢋꢐꢛꢀꢏꢈꢒꢀ9"ꢀꢋꢇꢈꢍꢐꢀ
are warranted for the ꢊꢋꢌꢁꢍ of the product on parts only.
#ꢀ "ꢊꢋꢋꢇꢈꢉꢀꢏꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢀꢐꢊꢑꢌꢀꢏꢐꢛꢀꢃꢊꢋꢀꢈꢁꢋꢀꢆꢇꢖꢇꢋꢍꢒꢀꢋꢁꢛꢀꢃꢏꢂꢐꢛꢀꢑꢌꢏꢇꢈꢐꢛꢀꢐꢓꢂꢁꢑꢘꢍꢋꢐꢛꢀꢃꢆꢏꢒꢍꢐꢛꢀꢏꢈꢒꢀꢈꢄꢆꢁꢈꢀꢋꢂꢇꢖꢖꢍꢂꢀꢌꢍꢏꢒꢐꢀꢙꢁꢂꢀꢂꢍꢐꢇꢒꢍꢈꢋꢇꢏꢆꢀꢁꢂꢀꢈꢁꢈ*ꢇꢈꢑꢁꢖꢍꢀ
producing use will be covered for failures due to defects in material or workmanship for a period of ꢎꢏꢅꢐꢇꢆꢉ from original product
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.
#ꢀꢀ !"#$ꢝꢐꢀꢕꢏꢓꢇꢒꢀ:ꢁꢏꢒꢍꢂꢀꢚꢋꢂꢇꢈꢉꢀ#ꢍꢏꢒꢀꢑꢏꢂꢂꢇꢍꢐꢀꢏꢀꢆꢇꢙꢍꢋꢇꢖꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢁꢈꢀꢋꢌꢍꢀꢆꢇꢈꢍꢀꢆꢁꢑꢘꢇꢈꢉꢀꢐꢄꢐꢋꢍꢖꢛꢀꢓꢏꢂꢋꢐꢀꢁꢈꢆꢄ;ꢀꢈꢁꢀꢆꢏꢃꢁꢂꢔꢀꢕꢍꢙꢍꢂꢀꢋꢁꢀꢄꢁꢊꢂꢀꢁꢓꢍꢂꢏꢋꢁꢂꢝꢐꢀ
manual for string head installation and maintenance instructions.
#ꢀꢀ <ꢆꢆꢀꢚ=*ꢚꢍꢂꢇꢍꢐꢀꢏꢈꢒꢀ>ꢕ$ꢀ<99<"#/!?9ꢀꢚ!ꢕ@!ꢚꢀꢚꢓꢆꢇꢋꢀꢚꢌꢏꢙꢋꢀꢏꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢀꢑꢏꢂꢂꢄꢀꢋꢌꢍꢀꢐꢏꢖꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢒꢊꢂꢏꢋꢇꢁꢈꢀꢏꢐꢀꢋꢌꢍꢀꢊꢈꢇꢋꢐꢀꢋꢌꢍꢄꢀꢏꢂꢍꢀ
ꢒꢍꢐꢇꢉꢈꢍꢒꢀꢋꢁꢀꢅꢋꢔ
COMMERCIAL APPLICATION
#ꢀꢀ 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income
producing use will be covered by this limited warranty for one ꢂꢑꢄꢅꢆꢁꢇꢈ from the date of purchase.
#ꢀꢀ 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this
limited warranty for two ꢂꢒꢄꢅꢆꢁꢇꢈꢉ from the date of purchase.
EXCEPTIONS:
#ꢀ 'ꢁꢂꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢍꢈꢉꢇꢈꢍꢀꢓꢁꢎꢍꢂꢍꢒꢀꢓꢂꢁꢒꢊꢑꢋꢐꢛꢀꢋꢌꢍꢀꢍꢆꢍꢑꢋꢂꢁꢈꢇꢑꢀꢇꢉꢈꢇꢋꢇꢁꢈꢀꢖꢁꢒꢊꢆꢍꢛꢀ\ꢍꢜꢇꢃꢆꢍꢀꢒꢂꢇꢗꢍꢀꢑꢏꢃꢆꢍꢐꢛꢀꢚꢕ/ꢀꢐꢁꢆꢇꢒꢀꢒꢂꢇꢗꢍꢀꢐꢌꢏꢙꢋꢐꢀꢏꢈꢒꢀ9"ꢀꢋꢇꢈꢍꢐꢛꢀ
are warranted for the ꢊꢋꢌꢁꢍ of the product on parts only.
#ꢀ "ꢊꢋꢋꢇꢈꢉꢀꢏꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢀꢐꢊꢑꢌꢀꢏꢐꢛꢀꢃꢊꢋꢀꢈꢁꢋꢀꢆꢇꢖꢇꢋꢍꢒꢀꢋꢁꢛꢀꢃꢏꢂꢐꢛꢀꢑꢌꢏꢇꢈꢐꢛꢀꢐꢓꢂꢁꢑꢘꢍꢋꢐꢛꢀꢃꢆꢏꢒꢍꢐꢛꢀꢏꢈꢒꢀꢈꢄꢆꢁꢈꢀꢋꢂꢇꢖꢖꢍꢂꢀꢌꢍꢏꢒꢐꢀꢙꢁꢂꢀꢑꢁꢖꢖꢍꢂꢑꢇꢏꢆꢛꢀꢇꢈꢐꢋꢇꢋꢊꢋꢇꢁꢈꢏꢆꢛꢀ
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period
of ꢓꢏꢅꢐꢇꢆꢉ from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by
this warranty.
#ꢀꢀ !"#$ꢝꢐꢀꢕꢏꢓꢇꢒꢀ:ꢁꢏꢒꢍꢂꢀꢚꢋꢂꢇꢈꢉꢀ#ꢍꢏꢒꢀꢑꢏꢂꢂꢇꢍꢐꢀꢏꢀꢆꢇꢙꢍꢋꢇꢖꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢁꢈꢀꢋꢌꢍꢀꢆꢇꢈꢍꢀꢆꢁꢑꢘꢇꢈꢉꢀꢐꢄꢐꢋꢍꢖꢛꢀꢓꢏꢂꢋꢐꢀꢁꢈꢆꢄ;ꢀꢈꢁꢀꢆꢏꢃꢁꢂꢔꢀꢕꢍꢙꢍꢂꢀꢋꢁꢀꢄꢁꢊꢂꢀꢁꢓꢍꢂꢏꢋꢁꢂꢝꢐꢀ
manual for string head installation and maintenance instructions.
#ꢀꢀ <ꢆꢆꢀꢚ=*ꢚꢍꢂꢇꢍꢐꢀꢏꢈꢒꢀ>ꢕ$ꢀ<99<"#/!?9ꢀꢚ!ꢕ@!ꢚꢀꢚꢓꢆꢇꢋꢀꢚꢌꢏꢙꢋꢀꢏꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢀꢑꢏꢂꢂꢄꢀꢋꢌꢍꢀꢐꢏꢖꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢒꢊꢂꢏꢋꢇꢁꢈꢀꢏꢐꢀꢋꢌꢍꢀꢊꢈꢇꢋꢐꢀꢋꢌꢍꢄꢀꢏꢂꢍꢀ
ꢒꢍꢐꢇꢉꢈꢍꢒꢀꢋꢁꢀꢅꢋꢔ
RENTAL APPLICATION - 90 DAYS WARRANTY
#ꢀꢀBꢈꢇꢋꢐꢀꢙꢁꢂꢀꢂꢍꢈꢋꢏꢆꢀꢊꢐꢍꢀꢎꢇꢆꢆꢀꢃꢍꢀꢑꢁꢗꢍꢂꢍꢒꢀꢏꢉꢏꢇꢈꢐꢋꢀꢒꢍꢙꢍꢑꢋꢐꢀꢇꢈꢀꢖꢏꢋꢍꢂꢇꢏꢆꢀꢏꢈꢒꢀꢎꢁꢂꢘꢖꢏꢈꢐꢌꢇꢓꢀꢙꢁꢂꢀꢏꢀꢓꢍꢂꢇꢁꢒꢀꢁꢙꢀGJꢀꢒꢏꢄꢐꢀꢙꢂꢁꢖꢀꢋꢌꢍꢀꢒꢏꢋꢍꢀꢁꢙꢀꢓꢊꢂꢑꢌꢏꢐꢍꢔꢀ
ꢍꢀꢀ !"#$ꢝꢐꢀꢆꢇꢏꢃꢇꢆꢇꢋꢄꢀꢊꢈꢒꢍꢂꢀꢋꢌꢍꢀO:ꢇꢙꢍꢋꢇꢖꢍPꢀꢑꢁꢗꢍꢂꢏꢉꢍꢀꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢋꢁꢀꢙꢊꢂꢈꢇꢐꢌꢇꢈꢉꢀꢓꢏꢂꢋꢐꢀꢐꢓꢍꢑꢇꢅꢍꢒꢀꢊꢈꢒꢍꢂꢀꢋꢌꢍꢀ>ꢕ$XB"9ꢀY<ꢕꢕ<?9Zꢀ>!ꢕ@$X section of
this warranty statement for OꢔꢋꢌꢁPꢀꢙꢂꢍꢍꢀꢁꢙꢀꢑꢌꢏꢂꢉꢍꢀꢙꢁꢂꢀꢏꢀꢓꢍꢂꢇꢁꢒꢀꢁꢙꢀꢋꢍꢈꢀ[\J]ꢀꢄꢍꢏꢂꢐꢀꢏꢙꢋꢍꢂꢀꢋꢌꢍꢀꢒꢏꢋꢍꢀꢁꢙꢀꢋꢌꢍꢀꢑꢁꢖꢓꢆꢍꢋꢍꢀꢊꢈꢇꢋꢝꢐꢀꢅꢈꢏꢆꢀꢓꢂꢁꢒꢊꢑꢋꢇꢁꢈꢔꢀ
X7722271109
33
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY STATEMENTS
SRM-225
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES
#ꢀꢀGJ*ꢒꢏꢄꢀꢂꢍꢐꢇꢒꢍꢈꢋꢇꢏꢆꢛꢀꢁꢂꢀꢈꢁꢈ*ꢇꢈꢑꢁꢖꢍꢀꢓꢂꢁꢒꢊꢑꢇꢈꢉꢀꢎꢏꢂꢂꢏꢈꢋꢄ
#ꢀꢀ^J*ꢒꢏꢄꢀꢑꢁꢖꢖꢍꢂꢑꢇꢏꢆꢛꢀꢇꢈꢐꢋꢇꢋꢊꢋꢇꢁꢈꢏꢆꢛꢀꢏꢉꢂꢇꢑꢊꢆꢋꢊꢂꢏꢆꢛꢀꢇꢈꢒꢊꢐꢋꢂꢇꢏꢆꢛꢀꢇꢈꢑꢁꢖꢍꢀꢓꢂꢁꢒꢊꢑꢇꢈꢉꢛꢀꢁꢂꢀꢂꢍꢈꢋꢏꢆꢀꢏꢓꢓꢆꢇꢑꢏꢋꢇꢁꢈꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢀ
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD
13738 and JASO M345FD Standards. ꢕꢖꢗꢘꢅꢙꢚ!ꢁꢈꢅ"ꢊꢁ#ꢐ(ꢅ%!ꢚ&()ꢈꢚ*ꢁꢅꢘꢋꢊ ꢇꢐꢀꢏꢀꢓꢂꢍꢖꢇꢊꢖꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢁꢇꢆꢀꢐꢓꢍꢑꢇꢅꢑꢏꢆꢆꢄꢀꢙꢁꢂꢖꢊꢆꢏꢋꢍꢒꢀꢋꢁꢀꢖꢍꢍꢋꢀ@ꢚ$*
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
#ꢀ
:ꢏꢑꢘꢀꢁꢙꢀꢆꢊꢃꢂꢇꢑꢏꢋꢇꢁꢈꢀꢁꢂꢀꢍꢈꢉꢇꢈꢍꢀꢙꢏꢇꢆꢊꢂꢍꢛꢀꢒꢊꢍꢀꢋꢁꢀꢋꢌꢍꢀꢊꢐꢍꢀꢁꢙꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢁꢇꢆꢐꢀthat do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered
oil, will void the two-stroke engine limited warranty. !"#$ꢀ>ꢁꢎꢍꢂꢀ=ꢆꢍꢈꢒ(ꢀ9ꢎꢁ*ꢚꢋꢂꢁꢘꢍꢀ$ꢇꢆ meets the ISO-L-EGD and JASO M345FD
Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per
the statement listed in the EPA or California Emission Defect Warranty Explanation.
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢊꢐꢍꢀꢁꢙꢀꢉꢏꢐꢁꢌꢁꢆꢛꢀꢑꢁꢈꢋꢏꢇꢈꢇꢈꢉꢀꢖꢍꢋꢌꢏꢈꢁꢆꢀ[ꢎꢁꢁꢒꢀꢏꢆꢑꢁꢌꢁꢆ]ꢛꢀꢁꢂꢀꢉꢏꢐꢁꢆꢇꢈꢍꢀꢑꢁꢈꢋꢏꢇꢈꢇꢈꢉꢀꢆꢍꢐꢐꢀꢋꢌꢏꢈꢀ|Gꢀꢁꢑꢋꢏꢈꢍ. Only use gasoline which
contains |Gꢀꢁꢑꢋꢏꢈꢍꢀꢁꢂꢀꢌꢇꢉꢌꢍꢂ. Gasohol which contains a +ꢇ6ꢋ+7+ꢀ\J}ꢀꢍꢋꢌꢏꢈꢁꢆꢀ[ꢉꢂꢏꢇꢈꢀꢏꢆꢑꢁꢌꢁꢆ]ꢀꢁꢂꢀ\~}ꢀ/9=!ꢀ[ꢖꢍꢋꢌꢄꢆꢋꢍꢂꢋꢇꢏꢂꢄꢃꢊꢋꢄꢆꢍꢋꢌꢍꢂ]ꢀ
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.
!ꢈꢉꢇꢈꢍꢀꢒꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢊꢐꢍꢀꢁꢙꢀꢍꢋꢌꢍꢂꢀꢁꢂꢀꢏꢈꢄꢀꢐꢋꢏꢂꢋꢇꢈꢉꢀ\ꢊꢇꢒꢐꢔꢀꢀ
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢋꢏꢖꢓꢍꢂꢇꢈꢉꢀꢎꢇꢋꢌꢀꢍꢈꢉꢇꢈꢍꢀꢐꢓꢍꢍꢒꢀꢉꢁꢗꢍꢂꢈꢁꢂꢀꢁꢂꢀꢍꢖꢇꢐꢐꢇꢁꢈꢀꢑꢁꢖꢓꢁꢈꢍꢈꢋꢐꢛꢀꢁꢂꢀꢂꢊꢈꢈꢇꢈꢉꢀꢍꢈꢉꢇꢈꢍꢐꢀꢏꢃꢁꢗꢍꢀꢐꢓꢍꢑꢇꢅꢍꢒꢀꢏꢈꢒꢀꢂꢍꢑꢁꢖꢖꢍꢈꢒꢍꢒꢀ
engine speeds as listed in your operator’s manual.
#ꢀ
#ꢀ
#ꢀ
#ꢀ
#ꢀ
#ꢀ
$ꢓꢍꢂꢏꢋꢇꢁꢈꢀꢁꢙꢀꢋꢌꢍꢀꢊꢈꢇꢋꢀꢎꢇꢋꢌꢀꢇꢖꢓꢂꢁꢓꢍꢂꢆꢄꢀꢖꢏꢇꢈꢋꢏꢇꢈꢍꢒꢂꢍꢖꢁꢗꢍꢒꢀꢑꢊꢋꢋꢇꢈꢉꢀꢐꢌꢇꢍꢆꢒꢀꢁꢂꢀꢂꢍꢖꢁꢗꢍꢒꢒꢏꢖꢏꢉꢍꢒꢀꢏꢇꢂꢀꢅꢆꢋꢍꢂꢔꢀꢀ
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢒꢇꢂꢋꢛꢀꢓꢂꢍꢐꢐꢊꢂꢍꢀꢁꢂꢀꢐꢋꢍꢏꢖꢀꢑꢆꢍꢏꢈꢇꢈꢉꢀꢋꢌꢍꢀꢊꢈꢇꢋꢛꢀꢐꢏꢆꢋꢀꢎꢏꢋꢍꢂꢛꢀꢑꢁꢂꢂꢁꢐꢇꢁꢈꢛꢀꢂꢊꢐꢋꢛꢀꢗꢏꢂꢈꢇꢐꢌꢛꢀꢏꢃꢂꢏꢐꢇꢗꢍꢐꢛꢀꢏꢈꢒꢀꢖꢁꢇꢐꢋꢊꢂꢍꢔ
Xꢍꢙꢍꢑꢋꢐꢛꢀꢖꢏꢆꢙꢊꢈꢑꢋꢇꢁꢈꢐꢀꢁꢂꢀꢙꢏꢇꢆꢊꢂꢍꢐꢀꢂꢍꢐꢊꢆꢋꢇꢈꢉꢀꢙꢂꢁꢖꢀꢏꢃꢊꢐꢍꢛꢀꢖꢇꢐꢊꢐꢍꢛꢀꢈꢍꢉꢆꢍꢑꢋꢛꢀꢖꢁꢒꢇꢅꢑꢏꢋꢇꢁꢈꢐꢛꢀꢏꢆꢋꢍꢂꢏꢋꢇꢁꢈꢐꢛꢀꢈꢁꢂꢖꢏꢆꢀꢎꢍꢏꢂꢛꢀꢇꢖꢓꢂꢁꢓꢍꢂꢀꢐꢍꢂꢗꢇꢑꢇꢈꢉꢛꢀꢁꢂꢀꢊꢐꢍꢀ
of unauthorized attachments.
#ꢀ
#ꢀ
@ꢈꢑꢁꢂꢂꢍꢑꢋꢀꢐꢋꢁꢂꢏꢉꢍꢀꢓꢂꢁꢑꢍꢒꢊꢂꢍꢐꢛꢀꢐꢋꢏꢆꢍꢀꢙꢊꢍꢆꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢙꢏꢇꢆꢊꢂꢍꢀꢋꢁꢀꢓꢂꢁꢗꢇꢒꢍꢀꢁꢂꢀꢓꢍꢂꢙꢁꢂꢖꢀꢂꢍ€ꢊꢇꢂꢍꢒꢀꢖꢏꢇꢈꢋꢍꢈꢏꢈꢑꢍꢀꢐꢍꢂꢗꢇꢑꢍꢐꢀꢏꢐꢀꢓꢂꢍꢐꢑꢂꢇꢃꢍꢒꢀꢇꢈꢀꢋꢌꢍꢀꢁꢓꢍꢂꢏꢋꢁꢂꢐꢀ
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.
'ꢏꢇꢆꢊꢂꢍꢐꢀꢒꢊꢍꢀꢋꢁꢀꢇꢖꢓꢂꢁꢓꢍꢂꢀꢐꢍꢋ*ꢊꢓꢛꢀꢓꢂꢍ*ꢒꢍꢆꢇꢗꢍꢂꢄꢀꢐꢍꢂꢗꢇꢑꢍꢀꢁꢂꢀꢂꢍꢓꢏꢇꢂꢀꢐꢍꢂꢗꢇꢑꢍꢀꢃꢄꢀꢏꢈꢄꢁꢈꢍꢀꢁꢋꢌꢍꢂꢀꢋꢌꢏꢈꢀꢏꢊꢋꢌꢁꢂꢇ%ꢍꢒꢀ!"#$ꢀꢐꢍꢂꢗꢇꢑꢇꢈꢉꢀꢒꢍꢏꢆꢍꢂꢀꢒꢊꢂꢇꢈꢉꢀꢋꢌꢍꢀ
warranty period.
"ꢍꢂꢋꢏꢇꢈꢀparts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
Bꢐꢍꢀꢁꢙꢀꢐꢓꢏꢂꢘꢀꢓꢆꢊꢉꢐꢀꢁꢋꢌꢍꢂꢀꢋꢌꢏꢈꢀꢋꢌꢁꢐꢍꢀꢖꢍꢍꢋꢇꢈꢉꢀꢓꢍꢂꢙꢁꢂꢖꢏꢈꢑꢍꢀꢏꢈꢒꢀꢒꢊꢂꢏꢃꢇꢆꢇꢋꢄꢀꢂꢍ€ꢊꢇꢂꢍꢖꢍꢈꢋꢐꢀꢁꢙꢀꢋꢌꢍꢀ$!/ꢀꢐꢓꢏꢂꢘꢀꢓꢆꢊꢉꢀꢆꢇꢐꢋꢍꢒꢀꢇꢈꢀꢋꢌꢍꢀ$ꢓꢍꢂꢏꢋꢁꢂꢐꢀ
Manuals.
$ꢗꢍꢂꢌꢍꢏꢋꢇꢈꢉꢀꢁꢂꢀꢑꢏꢂꢃꢁꢈꢀꢐꢑꢁꢂꢇꢈꢉꢀꢙꢏꢇꢆꢊꢂꢍꢐꢀꢒꢊꢍꢀꢋꢁꢀꢂꢍꢐꢋꢂꢇꢑꢋꢍꢒꢛꢀꢑꢆꢁꢉꢉꢍꢒꢀꢍꢜꢌꢏꢊꢐꢋꢀꢓꢁꢂꢋꢀꢁꢂꢀꢑꢁꢖꢃꢊꢐꢋꢇꢁꢈꢀꢑꢌꢏꢖꢃꢍꢂꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢒꢏꢖꢏꢉꢍꢀꢋꢁꢀꢐꢓꢏꢂꢘꢀꢏꢂꢂꢍꢐꢋꢍꢂꢀ
screen.
#ꢀ
#ꢀ
#ꢀ
#ꢀ
#ꢀ
<ꢒƒꢊꢐꢋꢖꢍꢈꢋꢐꢀꢏꢙꢋꢍꢂꢀꢋꢌꢍꢀꢅꢂꢐꢋꢀ[^J]ꢀꢋꢌꢇꢂꢋꢄꢀꢒꢏꢄꢐꢀꢏꢈꢒꢀꢃꢍꢄꢁꢈꢒꢛꢀꢐꢊꢑꢌꢀꢏꢐꢀꢑꢏꢂꢃꢊꢂꢍꢋꢁꢂꢀꢏꢒƒꢊꢐꢋꢖꢍꢈꢋꢀꢏꢈꢒꢀꢋꢌꢂꢁꢋꢋꢆꢍꢀꢑꢏꢃꢆꢍꢀꢏꢒƒꢊꢐꢋꢖꢍꢈꢋꢔꢀ
Xꢏꢖꢏꢉꢍꢀꢋꢁꢀꢉꢍꢏꢂꢐꢀꢁꢂꢀꢉꢍꢏꢂꢀꢑꢏꢐꢍꢐꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢑꢁꢈꢋꢏꢖꢇꢈꢏꢋꢍꢒꢀꢉꢂꢍꢏꢐꢍꢀꢁꢂꢀꢁꢇꢆꢛꢀꢊꢐꢍꢀꢁꢙꢀꢇꢈꢑꢁꢂꢂꢍꢑꢋꢀꢋꢄꢓꢍꢀꢁꢂꢀꢗꢇꢐꢑꢁꢐꢇꢋꢄꢀꢁꢙꢀꢆꢊꢃꢂꢇꢑꢏꢈꢋꢐꢛꢀꢏꢈꢒꢁꢂꢀꢙꢏꢇꢆꢊꢂꢍꢀꢋꢁꢀꢑꢁꢖꢓꢆꢄꢀ
with recommended grease or oil change intervals.
#ꢀ
#ꢀ
#ꢀ
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢆꢁꢏꢒꢇꢈꢉꢀꢚ#ꢕ!Xꢀ?ꢀ„<"® beyond recommended capacity.
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢓꢊꢖꢓꢀꢁꢂꢀꢐꢓꢂꢏꢄꢍꢂꢀꢂꢊꢈꢈꢇꢈꢉꢀꢒꢂꢄꢛꢀꢓꢊꢖꢓꢇꢈꢉꢀꢁꢂꢀꢐꢓꢂꢏꢄꢇꢈꢉꢀꢑꢏꢊꢐꢋꢇꢑꢀꢁꢂꢀ\ꢏꢖꢖꢏꢃꢆꢍꢀꢖꢏꢋꢍꢂꢇꢏꢆꢐꢛꢀꢁꢂꢀꢆꢏꢑꢘꢀꢁꢙꢀꢁꢂꢀꢃꢂꢁꢘꢍꢈꢀꢐꢋꢂꢏꢇꢈꢍꢂꢐꢔꢀ
<ꢒꢒꢇꢋꢇꢁꢈꢏꢆꢀꢒꢏꢖꢏꢉꢍꢀꢋꢁꢀꢓꢏꢂꢋꢐꢀꢁꢂꢀꢑꢁꢖꢓꢁꢈꢍꢈꢋꢐꢀꢒꢊꢍꢀꢋꢁꢀꢑꢁꢈꢋꢇꢈꢊꢍꢒꢀꢊꢐꢍꢀꢏꢙꢋꢍꢂꢀꢁꢓꢍꢂꢏꢋꢇꢁꢈꢏꢆꢀꢓꢂꢁꢃꢆꢍꢖꢀꢁꢂꢀꢙꢏꢇꢆꢊꢂꢍꢀꢁꢑꢑꢊꢂꢐꢔꢀꢚꢌꢁꢊꢆꢒꢀꢁꢓꢍꢂꢏꢋꢇꢁꢈꢏꢆꢀꢓꢂꢁꢃꢆꢍꢖꢀꢁꢂꢀ
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting
WWW.ECHO-USA.COMꢔꢀZꢁꢊꢂꢀꢂꢍꢑꢍꢇꢓꢋꢀꢁꢙꢀꢓꢊꢂꢑꢌꢏꢐꢍꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢒꢏꢋꢍꢛꢀꢖꢁꢒꢍꢆꢀꢏꢈꢒꢀꢐꢍꢂꢇꢏꢆꢀꢈꢊꢖꢃꢍꢂꢀꢖꢊꢐꢋꢀꢃꢍꢀꢖꢏꢇꢈꢋꢏꢇꢈꢍꢒꢀꢏꢈꢒꢀꢓꢂꢍꢐꢍꢈꢋꢍꢒꢀꢋꢁꢀꢏꢈꢀꢏꢊꢋꢌꢁꢂꢇ%ꢍꢒꢀ
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or
ꢑꢁꢈꢐꢍ€ꢊꢍꢈꢋꢇꢏꢆꢀꢒꢏꢖꢏꢉꢍꢐꢛꢀꢐꢁꢀꢄꢁꢊꢀꢖꢏꢄꢀꢏꢆꢐꢁꢀꢌꢏꢗꢍꢀꢁꢋꢌꢍꢂꢀꢐꢓꢍꢑꢇꢅꢑꢀꢆꢍꢉꢏꢆꢀꢂꢇꢉꢌꢋꢐꢀꢎꢌꢇꢑꢌꢀꢗꢏꢂꢄꢀꢙꢂꢁꢖꢀꢐꢋꢏꢋꢍꢀꢋꢁꢀꢐꢋꢏꢋꢍꢔꢀ9ꢌꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢇꢐꢀꢉꢇꢗꢍꢈꢀꢃꢄꢀ!"#$ꢀ
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES
9ꢌꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢇꢐꢀꢇꢈꢀꢆꢇꢍꢊꢀꢁꢙꢀꢏꢆꢆꢀꢁꢋꢌꢍꢂꢀꢍꢜꢓꢂꢍꢐꢐꢍꢒꢀꢁꢂꢀꢇꢖꢓꢆꢇꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢇꢍꢐꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢏꢈꢄꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢁꢙꢀ'@9?!ꢚꢚꢀ'$ꢕꢀ<ꢀ><ꢕ9@"B:<ꢕꢀ>Bꢕ>$ꢚ!ꢀ
OR USE and any implied warranty of MERCHANTABILITYꢀꢁꢋꢌꢍꢂꢎꢇꢐꢍꢀꢏꢓꢓꢆꢇꢑꢏꢃꢆꢍꢀꢋꢁꢀꢋꢌꢇꢐꢀꢓꢂꢁꢒꢊꢑꢋꢔꢀ!"#$ꢀꢏꢈꢒꢀꢇꢋꢐꢀꢏꢙꢅꢆꢇꢏꢋꢍꢒꢀꢑꢁꢖꢓꢏꢈꢇꢍꢐꢀꢐꢌꢏꢆꢆꢀꢈꢁꢋꢀꢃꢍꢀ
ꢆꢇꢏꢃꢆꢍꢀꢙꢁꢂꢀꢏꢈꢄꢀꢐꢓꢍꢑꢇꢏꢆꢀꢇꢈꢑꢇꢒꢍꢈꢋꢏꢆꢀꢁꢂꢀꢑꢁꢈꢐꢍ€ꢊꢍꢈꢋꢇꢏꢆꢀꢒꢏꢖꢏꢉꢍꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢆꢁꢐꢋꢀꢓꢂꢁꢅꢋꢐꢔꢀ9ꢌꢍꢂꢍꢀꢏꢂꢍꢀꢈꢁꢀꢎꢏꢂꢂꢏꢈꢋꢇꢍꢐꢀꢍꢜꢋꢍꢈꢒꢍꢒꢀꢁꢋꢌꢍꢂꢀꢋꢌꢏꢈꢀꢏꢐꢀꢓꢂꢁꢗꢇꢒꢍꢒꢀꢌꢍꢂꢍꢇꢈꢔꢀ
9ꢌꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢖꢏꢄꢀꢃꢍꢀꢖꢁꢒꢇꢅꢍꢒꢀꢁꢈꢆꢄꢀꢃꢄꢀ!"#$ꢔ
99922201032
11/18/2011
34
X7722271109
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SRM-225
NOTES
NOTES
X7722271109
35
© 2/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
S04011051023/S04011999999
S96811001001/S96811999999
S03912425291/S03912999999
S89312001001/S89312999999
ECHO, INCORPORATED
400 Oakwood Road
Lake Zurich, IL 60047
36
Download from Www.Somanuals.com. All Manuals Search And Download.
|
