Power Blower
Operator’s Manual
MODEL PB-410
WARNING
Read rules for safe operation and all instructions carefully. ECHO provides this
DANGER
Operator’s Manual which must be read and understood for proper and safe operation.
X750-006 20 1
X750109-290 1
Printed in Japan 0501Gjb 0044 ES
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
3
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words. The following is an explanation of those symbols and key
words and what they mean to you.
This symbol accompanied by the words WARN-
ING and DANGER calls attention to an act or
condition that can lead to serious personal injury
to operator and bystanders.
IMPORTANT The enclosed message
provides information necessary for the
protection of the unit.
The circle with the slash symbol means whatever is
shown within the circle is prohibited.
NOTE This enclosed message provides
tips for use, care and maintenance of the
unit.
SAFETY
HOT DECAL
DECALS
Locate these safety decals on your unit. The complete unit illustration,
found in the “DESCRIPTION” section, will help you locate them.
Make sure the decals are legible and that you understand and follow the
instructions on them. If a decal cannot be read, a new one can be
ordered from your ECHO dealer.
P/N89016006361
P/N89016003360
-WARNING-
-DANGER-
- ADVERTENCIA
- PELIGRO
Lea y obedezca todas las
precaucionesdeseguridadque
aparecen en el Manual del
Operador.Losoperadores,los
asistentes y los espectadores
puedenrecibirlesionesgraves
debido a los objetos que se
soplan y tienen que usar la
protección para ojos ANSI
Z87.1.Siempreuseprotección
para los oídos cuando opere.
Read and follow all safety
precautions in the operator’s
manual. Operators, helpers &
bystanders can be severely
injured by blown objects and
must wear specified ANSI
Z87.1 eye protection. Always
wear hearing protection when
operating.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
INTERNATIONAL SYMBOLS
Symbol
Symbol
description/application
Symbol
description/application
Symbol
description/application
Symbol form/shape
Symbol form/shape
Symbol form/shape
Symbol form/shape
description/application
Read and under-
stand Operator’s
Manual.
Fuel and oil
mixture
Ignition
ON/OFF
Engine choke
control.
Wear eyes, ears and
head protection
Finger Severing
Emergency stop
Primer bulb
Wear hand
protection. Use
two handed.
Carburetor
adjustment
- Low speed mixture
Carburetor
adjustment
- High speed mixture
Hot
Surface
Choke Control
"Run"
Position
Wear slip resistant
foot wear.
Carburetor
adjustment
- Idle speed
Safety/Alert
(ChokeOpen)
DO NOT allow
flames or sparks
near fuel.
DO NOT smoke
near fuel.
EQUIPMENT
Before operation a complete check of the unit must be performed:
• Check unit for loose/missing nuts, bolts and screws. Tighten
and/or replace as needed.
• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO
NOT operate unit if leaks are found.
Spark Arrestor - Catalytic Muffler / Muffler
• The muffler or catalytic muffler controls the exhaust noise and
emissions. The spark arrestor screen prevents hot, glowing particles
of carbon from leaving the muffler. Make sure the spark arrestor
screen is in good repair and properly seated in the muffler. Keep
exhaust area clear of flammable debris. Avoid contact during and
immediately after operation.
Parts
ATTACHMENTS
AND
• Do not use blower if any part is missing or damaged.
• Have repairs done only by an authorized ECHO Service dealer.
• Do not use any attachment, accessory or replacement part unless it is
recommended in this Operator’s Manual.
ACCESSORIES
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
5
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING
DANGER
Power Blower users risk injury to themselves and others if the Power Blower is used improperly and/or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating a Power Blower.
Physical Condition --
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection --
Wear eye protection that meets ANSI Z87.1 or CE requirements
whenever you operate the blower.
Hand Protection --
Wear no-slip, heavy duty work gloves to improve your grip on the
blower handle. Gloves also reduce the transmission of machine
vibration to your hands.
Breathing Protection --
Wear a face mask to protect against dust.
Hearing Protection --
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing --
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY.
Wear sturdy work shoes with nonskid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Keep long hair away from engine and blower intake. Retain hair with
cap or net.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Hot Humid Weather --
Heavy protective clothing can increase operator fatigue which may lead
to heat stroke. Schedule heavy work for early morning or late afternoon
hours when temperatures are cooler.
SAFE OPERATION
Determine Operation Area --
•
•
•
Do not operate this product indoors or in inadequately ventilated
areas.
Review area to be cleared. Look for potential hazards such as stones
or metal objects.
Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the
blower is in use.
•
•
Take wind conditions into account: avoid open doors and windows.
Provide all operators of this equipment with the Operator's Manual
and instructions for safe operation.
•
Do not point blower at people or animals.
Use Proper Clothing & Equipment
•
Before starting the unit, equip yourself and any other person
working within the 15 m (50 ft.) Safety Zone with the required
Protective Equipment and clothing.
•
•
Keep long hair away from engine and blower intake. Retain hair
with cap or net.
Start unit on ground with throttle at idle. Check that blower pipe is
not blocked by the ground or by any objects.
15 m (50 ft.)
Keep A Solid Stance
•
Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders.
Do not perform Maintenance or Assembly procedures with engine
running.
•
Noise Control
•
•
•
Follow local noise regulations on sound levels and hours of opera-
tions. Use only during appropriate hours.
Never use a higher speed setting then necessary to perform a task.
The higher the engine speed the louder the blower noise.
Be a good neighbor.
Avoid Hot Surfaces
•
During operation, the muffler or catalytic muffler and surrounding
cover may become extremely hot. Avoid contact during and
immediately after operation. Always keep exhaust area clear of
flammable debris. Allow the engine and muffler to completely cool
before performing any maintenance activity.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
7
EXTENDED OPERATION / EXTREME CONDITIONS
Vibration and Cold --
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommended because the minimum exposure which might trigger the
ailment is unknown.
•
•
•
Keep your body warm, especially the head, neck, feet, ankles, hands
and wrists.
Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks and also by not smoking.
Limit the hours of operation. Try to fill each day with jobs where
operating the blower or other hand-held power equipment is not
required.
•
If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Repetitive Stress Injuries --
It is believed that overusing the muscles and tendons of the fingers,
hands, arms and shoulders may cause soreness, swelling, numbness,
weakness and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged exposure
to vibration may contribute to CTS. CTS can cause severe pain for
months or even years. To reduce the risk of RSI/CTS, do the following:
•
Avoid using your wrist in a bent, extended or twisted position.
Instead try to maintain a straight wrist position. Also, when grasp-
ing, use your whole hand, not just the thumb and index finger.
Take periodic breaks to minimize repetition and rest your hands.
Reduce the speed & force in which you do the repetitive movement.
Do exercises to strengthen the hand and arm muscles.
Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness or pain in the fingers, hands, wrists or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
•
•
•
•
Download from Www.Somanuals.com. All Manuals Search And Download.
8
DESCRIPTION
EMISSION CONTROL
EPA Phase II
The emission control system for these engines are
EM (Engine Modification).
An Emission Control Label is located on the engine. (This is an
EXAMPLE ONLY, information on label varies by engine FAMILY).
PRODUCT EMISSION DURABILITY
The 300 hours emission durability period is the time span selected by the manufacturer certifying the engine
emissions output meets applicable California emissions regulations, provided that approved maintenance
procedures are followed as listed in the Maintenance Section of this manual.
CONTENTS
1 - Power Head
1 - Blower Pipe Assembly
1 - Operator’s Manual
1 - Warranty Registration Card
1 - ECHO Emissions and Warranty Statement
1 - Echo Power Blend TM 2-stroke oil sample
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
9
1
P/N89016003360
2
8
10
5
4
6
7
11
9
P/N89016006361
3
1. AIR CLEANER - Contains replaceable air filter element.
2. SPARK PLUG - Provides spark to ignite fuel mixture.
3. MUFFLER/SPARK ARRESTOR -The spark arrestor muffler controls the exhaust noise while the spark arrestor
prevents hot, glowing particles of carbon from leaving the muffler.
4. RECOIL STARTER HANDLE - Pull recoil handle slowly until starter engages, then return handle slowly. DO
NOT let handle snap back or damage to unit will occur.
5. CHOKE LEVER - Push lever DOWN to close choke (starting position) and for emergency stopping.
Lift UP to open choke (run position).
6. FUEL TANK CAP - For closing the fuel tank.
7. THROTTLE LEVER - Controls engine speed.
8. STOP SWITCH - “Toggle Switch”
9. SHOULDER HARNESS - Used to support unit on operator’s back. The straps are adjustable.
10. BLOWER PIPES -
11. FLEXIBLE PIPE - Allows for full range of movement.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
SPECIFICATIONS
MODEL
PB-410
Length
330 mm (13.0 in.) (w/o pipes)
Width
440 mm (17.3 in.)
Height
440 mm (17.3 in.)
Mass (dry)
Engine Type
Displacement
Bore
9.7 kg (21.4 Ib.) (w/o pipes)
Air cooled, two-stroke, single cylinder gasoline engine
39.7 mL (2.42 cu. in.)
38.0 mm (1.50 in.)
Stroke
35.0 mm (1.38 in.)
Carburetor
Ignition System
Spark Plug
Exhaust System
Fuel
Walbro Diaphragm, model WT-684
Flywheel Magneto, capacitor discharge ignition type
NGK BPM-8Y Gap 0.65 mm (0.026 in.)
Spark Arrestor Muffler w / Catalyst
Mixed (Gasoline and Two-stroke Oil)
50:1 ECHO High Performance, two-stroke air cooled engine oil
89 Octane unleaded. DO NOT use fuel containing methyl alcohol.
Gasoline may contain 15 % MTBE (methyl tertiary-butyl ether).
50:1 ECHO High Performance, two-stroke air cooled engine oil
1.5 L (50.7 US fl. oz.)
Fuel/Oil Ratio
Gasoline
Oil
Fuel Tank Capacity
Recoil Starter System
Wide Open Throttle Speed (r/min)
Idle Speed (r/min)
Automatic Recoil Starter Centrifugal Type
7000 - 7600
2200 - 3000
Maximum Air Volume
Maximum Air Speed w/pipes (m/s)
10.6 m3/min. (375 cu. ft./min.)
78 (175 mph)
Sound Level at 50 ft. dB(A) scale per 72 dB(A)
ANSI B175.2
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
11
ASSEMBLY
WARNING
DANGER
Never perform maintenance or assembly procedures with engine
running or serious personal injury may result.
Stick handle
Clamp
INSTALL BLOWER PIPES
1. Assemble throttle lever bracket to the fancase using four screws.
- Set stop lead into the recess of bracket.
Elbow
2. Assemble the flexible pipe thru elbow to the blower and tighten
clamp.
3. Assemble the flexible pipe and the straight pipe w/swivel and
tighten the clamp.
Pipe
Flexible pipe
4. Assemble straight section of the pipe to the other end of the pipe.
5. Assemble the curved pipe and rotate the desired angle.
6. Shoulder harness is adjustable to fit any operator.
7. Adjust the length of strap for easier operation.
Screws
Stop lead
INSTALL STICK HANDLE
1. Remove blower pipe from swivel tube.
Stick handle
Wing nut
2. Loosen wing nut completely and expand open stick handle.
3. Align notches in handle clamp with pipe pegs. Handle should be
angled away from operator.
Notch
Pipe pegs
Swivel
tube
4. Slide handle onto swivel tube.
5. Position handle for comfortable operation and tighten wing nut.
6. Install blower pipe to swivel tube.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
PRE-OPERATION
FUEL
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline
known to be good quality. Gasoline may contain up to 15% MTBE
(methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol
is NOT approved.
TwoStrokeOil-Atwo-strokeengineoilmeetingISO-L-EGD(ISO/CD
13738) and J.A.S.O. FC Standards must be used. Echo brand premium
Power Blend TM Universal 2-Stroke Oil meets these standards. Engine
problems due to inadequate lubrication caused by failure to use an
ISO-L-EGDandJ.A.S.O.FCcertifiedoil,suchasEchopremiumPower
Blend TM, will void the two-stroke engine warranty. (Emission related
parts only are covered for two years, regardless of two-stroke oil used,
per the statement listed in the Emission Defect Warranty Explanation.)
Fuel to Oil Mix - 50:1 Ratio
U.S.
METRIC
GAS
GAS
OIL
OIL
cc.
Gallons
Fl. oz.
Liter
1
2
5
2.6
5.2
13
4
8
20
80
160
400
IMPORTANT
EchopremiumPowerBlendTM Universal2-StrokeOilmaybemixed
at 50:1 ratio for application in all Echo engines sold in the past
regardless of ratio specified in those manuals.
Handling Fuel
WARNING
DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling or serious personal injury may result.
• Use an approved fuel container.
• DONOTsmokenearfuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps
slowly allowing pressure to equalize.
• NEVERrefuelaunitwhentheengineisHOTorRUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors
over bare ground.
• DO NOT overfill fuel tank. It is not permitted to fill fuel above the
shoulder level of fuel tank. Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after
refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.
Shoulder
level
Fueltank
• Move at least 3m (10 ft.) from refueling location before starting
the engine.
3 m (10 ft.)
MINIMUM
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
13
Mixing Instructions
1. Fill an approved fuel container with half of the required amount of
gasoline.
2. Add the proper amount of 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Add remaining gasoline, close fuel container, and remix.
IMPORTANT
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers
to reduce fuel spillage.
After use
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.
Storage - Fuel storage laws vary by locality. Contact your local
government for the laws affecting your area. As a precaution, store fuel
in an approved, airtight container. Store in a well-ventilated, unoccu-
pied building, away from sparks and flames.
S M T W T F
S
7
1
8
2
3
4 5 6
IMPORTANT
Stored fuel ages. Do not mix more fuel than you expect to use in
thirty (30) days, ninety (90) days when a fuel stabilizer is added.
9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31
Stored two-stroke fuel may separate. ALWAYS shake fuel
container thoroughly before each use.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
OPERATION
Recoil starter handle
- Provide all operators of this equipment with the Operator’s Manual
and instructions for safe operation.
- Check unit for loose nuts, bolts and screws daily.
- Recoil starter: Use short pulls - only 1/2 - 2/3 of rope length for
starting. Do not allow the rope to snap back in. Always hold the unit
firmly.
- Rotate spring loaded throttle handle downward to a comfortable
operating position.
STARTING COLD ENGINE
Choke lever
Open choke
WARNING
DANGER
When engine is started, confirm if there is not any abnormal
vibration or sound. If there is abnormal vibration or sound, ask your
dealer to repair.
1. Turn switch to “RUN” position.
Close choke
2. Close choke (move choke lever down) and pull recoil starter
handle until engine fires.
3. Open choke and if necessary, restart engine.
NOTE
Allow engine to warm up before use.
STARTING WARM ENGINE
1. Turn switch to “RUN” position.
STOP
RUN
2. Move throttle lever to start/idle position, pull recoil starter handle
5 times and engine should start. Do not use choke.
NOTE
If engine does not start after 4 pulls, use cold start procedures.
STOPPING ENGINE
1. Move throttle lever to idle position and allow engine to run at idle
for a few minutes.
High speed
2. Move switch to “STOP” position.
WARNING
DANGER
START
If engine does not stop, move choke lever to closed position to stall
engine. Check and repair stop switch before starting engine again or
serious personal injury may result.
Idling
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
15
OPERATING BLOWER
WARNING
DANGER
Always wear safety glasses, hearing protection, a face filter mask
and take all safety precautions or serious personal injury may result.
Do not point the blower pipe in the direction of people or pets.
Read the Safety Section carefully.
IMPORTANT
To avoid engine damage due to over revving, do not block
blower pipe opening.
1. Use only during appropriate hours.
2. Make sure bevel at end of pipe faces downward.
3. Allow the engine to warm up at a fast idle for a few minutes.
4. Set engine speed.
5. Use lower speed to blow dry leaves from a lawn or flower bed.
6. Additional speed may be necessary to clean grass and leaves from
walks, patios and drives.
7. Higher speed may be necessary to move gravel, dirt, snow, bottles
or cans from a driveway, street, parking lot or stadium.
NOTE
Never use a higher speed setting than necessary to perform a task.
Remember, the higher the engine speed, the louder the blower
noise. Minimize dust by using blower at lower speeds when
necessary. Keep debris on your property.
Be a good neighbor.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
MAINTENANCE
Your ECHO blower is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
your blower achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your
unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have
the ECHO Dealer do it, each maintenance task has been graded. If task is not listed, see your ECHO Dealer for repairs.
SKILL LEVELS
Level 1 = Easy to do. Most required tools come with unit.
Level 2 = Moderate difficulty. Some specialized tools may be required.
Level 3 = Experience required. Specialized tools are required. ECHO recommends
that the unit be returned to your ECHO dealer for service.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. Just below each task
heading are listed the various part numbers required for that task. See your ECHO dealer for these parts.
MAINTENANCE INTERVALS
DAILY
OR
3
6
REQ'D
SKILL
LEVEL
COMPONENT/
SYSTEM
MAINTENANCE
PROCEDURE
EVERY MONTHS MONTHS
YEARLY
BEFORE REFUEL
USE
OR 90
OR 270
HOURS
HOURS
Recommended ECHO Dealer Maintenance Procedures
Cylinder Exhaust Port Inspect/Clean/Decarbon
3
3
I/C
Fuel System, Leaks
Replace
R*
Do-It-Yourself Maintenace Procedures
Air Filter
Inspect/Clean/Replace
Inspect/Clean
Inspect/Replace
Inspect
1
2
1
1
2
2
1
2
1
I/C
I/C
R*
I
Choke
Fuel Filter
R*
Fuel System, Leaks
Cooling System
I
I
Inspect/Clean
I/C
Muffler Spark Arrestor Inspect/Replace
I/R*
I/C
Recoil Starter Rope
Spark Plug
Inspect/Clean
I/C
I/R*
Inspect/Clean
R*
Screws/Nuts/Bolts
Inspect/Tighten/Replace
I/R*
MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN
Time intervals shown are maximum. Actual use and your experience will determine the frequency
IMPORTANT NOTE -
of required maintenance.
MAINTENACE PROCEDURE NOTES:
*All recommendations to replace are based on the finding damage or wear during inspection.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
17
AIR FILTER
Level 1.
NOTE
Clean daily.
1. Close choke (Cold Start Position). This prevents dirt from
entering the carburetor throat when the air filter is removed.
Brush accumulated dirt from the air cleaner area.
Air cleaner cover
Element
Clamp
2. To take out a air filter, loosen both clamps of air cleaner and
remove filter cover as shown.
3. Clean and inspect the element for damage. If element is fuel
soaked and very dirty, replace it.
4. If element can be cleaned and reused, be certain it:
•still fits the cavity in the air cleaner cover.
•is installed with the original side out.
FUEL FILTER
Level 1.
WARNING
Fuel is VERY flammable. Use extreme care when mixing, storing
DANGER
or handling.
1. Use a clean rag to remove loose dirt from around fuel cap and
empty fuel tank.
2. Use the “fuel line hook” to pull the fuel line and filter from the
tank.
Fuel filter
3. Remove the filter from the line and install the new filter.
CHECK FUEL SYSTEM
Level 1 or 3.
1. Check before every use. (Level 1)
2. After refueling make sure fuel does not leak or exude from around
fuel pipe, fuel grommet or fuel tank cap. (Level 1)
3. In case of fuel leakage or exudation there is a danger of fire. Stop
using the machine immediately and request your dealer to inspect
or replace. (Level 3)
Download from Www.Somanuals.com. All Manuals Search And Download.
18
WARNING
DANGER
Muffler and catalytic mufflers operate at extremely high tempera-
tures. Muffler area must be kept clean. Do not perform maintenance
on the engine or muffler until engine and muffler are completely
cool, otherwise serious personal injury may occur.
SPARK PLUG
Level 2.
1. Remove spark plug and check for fouling, worn and rounded
center electrode.
2. Clean the plug or replace with a new one. DO NOT sand blast to
clean. Remaining sand will damage engine.
3. Adjust spark plug gap by bending outer electrode.
4. Tighten spark plug to 15 - 17 N•m (130 - 145 in. lb.).
0.65 mm
(0.026 in.)
COOLING SYSTEMS
Level 2.
IMPORTANT
To maintain proper engine operating temperatures, cooling air must
pass freely through the cylinder fin area. This flow of air carries
combustion heat away from the engine.
INTAKE
GRILL
Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from reaching the
cylinder.
• Dust and grass build up on the outside of the cylinder. This build up
insulates the engine and prevents the heat from leaving.
Removal of cooling passage blockages or cleaning of cooling fins is
considered “Normal Maintenance”. Any failure attributed to lack of
maintenance is not warranted.
Cleaning Grill
• Brush accumulated debris from intake grill.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
19
Cleaning Cylinder Fins
• Check periodically.
- Clogged fins result in poor engine cooling.
- Clean the passage of air between the cylinder fins to let cooling air
pass easily.
Cylinder fins
EXHAUST SYSTEM
Spark Arrestor Screen
Level 2.
IMPORTANT
Carbon deposits in muffler will cause a drop in engine output and
overheating. Spark arrestor screen must be checked periodically.
1. Remove spark arrestor cover, gaskets and spark arrestor screen
from muffler. Replace screen if plugged with carbon deposits.
Spark arrestor screen
NOTE
When cleaning carbon deposit, be careful not to damage the
catalytic body.
2. Install spark arrestor screen, gaskets, and cover.
3. Tighten all screws securely.
Cylinder Exhaust Port
Level 3.
Gaskets
IMPORTANT
Spark arrestor cover
The cylinder exhaust port must be inspected and cleaned of excess
carbon every 3 months or 90 hours of operation in order to maintain
this engine within the emissions durability period. ECHO strongly
recommends that you return your unit to your ECHO dealer for this
important maintenance service.
• In the event that the engine should lose power and overheat, the
muffler should be removed and checked for excessive deposits.
• Carbon build up in the exhaust port should be removed with a piece
of wood, ensuring that particles of carbon are not allowed to enter the
cylinder.
• Remove all carbon deposits from the muffler flange area and wash
the complete unit in a suitable solvent.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
CARBURETOR ADJUSTMENT
Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel
break-in before carburetor adjustments can be made. During the break-
in period your engine performance will increase and exhaust emissions
will stabilize. Idle speed can be adjusted as required.
High Altitude Adjustment
High altitude adjustment is not required for proper operation of this
engine.
Level 2.
NOTE
Every unit is run at the factory and the carburetor is set in
compliance with California Emission Regulations.
In addition, the carburetor is equipped with “H” (High Speed
Needle) and “L” (Low Speed Needle) needle adjustment limiters
that prevent settings outside acceptable limits.
1. Before adjusting carburetor clean or replace air filter and
muffler, “Spark Arrestor Screen”.
High speed needle (H)
Low speed needle (L)
Idle adjustment needle
2. Start engine and run several minutes to bring to operating
temperature. Flash choke twice during warm-up to clear any
air from the fuel system.
3. Stop engine. Turn “H” speed needle CCW (Counterclock-
wise) to stop. Turn “L” speed needle midway between full CW
(Clockwise) stop and CCW stop.
4. Idle Speed Adjustment
• Before adjusting blower, install all blower pipes.
Start engine, turn “idle” speed adjustment screw either CW
or CCW until the tip just contacts the throttle plate.
Then turn (2) two additional turns CW for initial setting.
Blower should operate with an even idle at low r/min.
5. Accelerate to full throttle for 2 - 3 seconds to clear any excess
fuel in the engine, then return to idle. Accelerate engine to full
throttle to check for smooth transition from idle to high speed.
If engine hesitates turn “L” needle CCW 1 /8 turn and repeat
acceleration. Continue adjustment until smooth acceleration
results.
6. Check idle speed and reset if necessary as described in item 4.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
21
TROUBLESHOOTING
TROUBLESHOOTING CHART
Status
Problem
Check
Cause
Remedy
Clean or replace
Fuel at carburetor
No fuel at carburetor Fuel strainer clogged
Fuel line clogged
Clean or replace
Carburetor
Ask your ECHO dealer
Ask your ECHO dealer
Fuel at cylinder
No fuel at cylinder
Carburetor
Muffler wet with fuel Fuel Mixture is too rich Open choke
Clean/replace air filter
Engine cranks -
starts hard/
Adjust carburetor
Ask your ECHO dealer
Turn switch to ON
doesn't start
No spark
No spark
Stop switch off
Spark at end of plug
wire
Electrical problem
Spark gap incorrect
Covered with carbon
Fouled with fuel
Plug defective
Ask your ECHO dealer
Spark at plug
Adjust to 0.65 mm (0.026 in.)
Clean or replace
Clean or replace
Replace plug
Air filter
Air filter dirty
Normal wear
Clean or replace
Fuel filter
Fuel filter dirty
Contaminants/residues Replace
in fuel
Fuel vent
Fuel vent plugged
Contaminants/residues Clean or replace
in fuel
Engine runs, but
dies or does not
accelerate
Spark plug
Plug dirty/worn
Normal wear
Clean and adjust or replace
Carburetor
Improper adjustment Vibration
Adjust
Clean
properly
Cooling system
Cooling system
dirty/plugged
Extended operation in
dirty/dusty locations
Spark arrestor
screen
Spaek arrestor screen Normal wear
plugged
Replace
Engine does not
crank
N/A
N/A
Internal engine problem Ask your ECHO dealer
Engine runs,
blower doesn't
work or is
Blower pipe
Pipe clogged
Pipe loose
Build-up of debirs
Vibration
Unclog
Tighten
Replace
Pipe damaged
Wear/Misuse
weak/uneven
WARNING DANGER
Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by ground-
ing spark plug near cylinder plug hole, otherwise serious personal injury may result.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
STORAGE
WARNING
DANGER
During operation the muffler or catalytic muffler and surrounding cover becomes hot. Always keep exhaust area
clear of flammable debris during transportation or when storing, otherwise serious property damage or personal
injury may result.
Long Term Storage (Over 30 Days)
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage mainte-
nance which includes the following:
1. Store unit in a dry, dust free place, out of the reach of children.
WARNING
DANGER
Do not store where fuel fumes may accumulate or reach an open
flame or spark.
2. Place the stop switch in the “STOP” position.
Stop switch
3. Remove accumulation of grease, oil, dirt and debris from exterior
of unit.
4. Perform all periodic lubrication and services that are required.
5. Tighten all screws and nuts.
6. Drain the fuel tank completely and pull the recoil starter handle
several times to remove fuel from the carburetor.
7. Remove the spark plug and pour 7 mL (1/4 oz.) of fresh, clean
ECHO 2-stroke engine oil into the cylinder through the spark plug
hole.
A. Place a clean cloth over the spark plug hole.
B. Pull the recoil starter handle 2 or 3 times to distribute the oil
inside the engine.
C. Observe the piston location through the spark plug hole.
Pull the recoil starter handle slowly until the piston reaches the
top of its travel and leave it there.
8. Install the spark plug (do not connect ignition cable).
9. Remove blower pipe assembly from unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR’S MANUAL
23
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING INFORMATION
PARTS
GenuineECHOPartsandECHOREPOWER™PartsandAssembliesfor
your ECHO products are available only from an Authorized ECHO
Dealer. When you do need to buy parts always have the Model
Number and Serial Number of the unit with you. You can find these
numbers on the engine housing. For future reference, write them in the
space provided below.
Model Number _____________ Serial Number ____________
SERVICE
DEALER?
Call
1-800-432-ECHO
or
An Authorized ECHO Service Dealer must perform Service of this
product during the warranty period. For the name and address of the
Authorized ECHO Service Dealer nearest you, ask your retailer or call:
1-800-432-ECHO(3246). Dealerinformationisalsoavailableonour
Web Site. When presenting your unit for Warranty service/repairs,
proof of purchase is required.
ECHO CONSUMER PRODUCT SUPPORT
If you require assistance or have questions concerning the application,
operation or maintenance of this product you may call the ECHO
ConsumerProductSupportDepartmentat1-800-673-1558from8:30am
to 4:30 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
WARRANTY REGISTRATION
You may register your Echo equipment using the warranty registration
direct link between you and Echo if we find it necessary to contact
you.
ADDITIONAL OR REPLACEMENT MANUALS
Safety Manuals in English/Spanish or English/French are available, free of charge, from your ECHO dealer or at
Operator’sandPartsManualsareavailableby:
• Downloadingfreefromwww.echo-usa.com
• Purchasing from your Echo Dealer.
• Manuals are available by sending a written request stating the model number and serial number of your Echo unit,
part number of the manual, your name and address, and mail to the address below.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
ECHO, INCORPORATED
400 Oakwood Road
Lake Zurich, IL 60047-1564
Download from Www.Somanuals.com. All Manuals Search And Download.
|