Fujitsu Air Conditioner P N9359944058 User Manual

OPERATING MANUAL  
MODE D’EMPLOI  
MANUAL DE FUNCIONAMIENTO  
AIR CONDITIONER  
FLOOR CONSOLE/  
UNDER CEILING  
DUAL TYPE  
KEEP THIS MANUAL  
FOR FUTURE REFERENCE  
P/N9359944058  
FUJITSU GENERAL LIMITED  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES AND FUNCTIONS  
AUTOMATIC OPERATION  
COOLING MODEL  
Merely press the START/STOP button, and the unit will  
begin automatic operation in the Cooling or Dry mode as  
appropriate, in accordance with the thermostat setting  
and the actual temperature of the room.  
HEAT & COOL MODEL (REVERSE CYCLE)  
Merely press the START/STOP button, and the unit will  
begin automatic operation in either the Heating, Cooling  
or Monitor modes as appropriate, in accordance with the  
thermostat setting and the actual temperature of the room.  
SLEEP TIMER  
COOLING MODEL  
When the SLEEP timer button is pressed during Cooling  
or Dry mode, the thermostat setting is gradually rised  
during the period of operation. When the set time is  
reached, the unit automatically turns off.  
HEAT & COOL MODEL (REVERSE CYCLE)  
When the SLEEP timer button is pressed during Heating  
mode, the air conditioner’s thermostat setting is gradu-  
ally lowered during the period of operation; during Cool-  
ing or Dry mode, the thermostat setting is gradually rised  
during the period of operation. When the set time is  
reached, the unit automatically turns off.  
WIRELESS REMOTE CONTROL UNIT  
The WIRELESS REMOTE CONTROL UNIT allows convenient  
control of air conditioner operation.  
OMNI-DIRECTIONAL AIR FLOW  
(SWING OPERATION)  
Three-dimensional control over air direction swing is possi-  
ble through dual use of both an UP/DOWN air direction swing  
and RIGHT/LEFT air direction swing. Since UP/DOWN air  
direction flaps operate automatically according to the oper-  
ating mode of the unit, it is possible to set air direction based  
on the operating mode.  
MILDEW-RESISTANT FILTER  
The AIR FILTER has been treated to resist mildew growth,  
thus allowing cleaner use and easier care.  
En-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NAME OF PARTS  
Instructions relating to heating (*) are applicable only to HEAT & COOL MODEL(Reverse Cycle).  
Fig. 1  
Fig. 3  
Fig
En-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fig. 1 Indoor Unit  
Fig. 4 Remote Control Unit  
1 Operating Control Panel (Fig. 2)  
2 MANUAL AUTO button  
C SLEEP button  
D MASTER CONTROL button  
E SET TEMP./SET TIME buttons (  
F Signal Transmitter  
3 Remote Control Signal Receiver  
4 OPERATION Indicator Lamp (red)  
5 TIMER Indicator Lamp (green)  
6 SWING Indicator Lamp (orange)  
(VERTICAL SWING)  
)
G TIMER button  
H FAN CONTROL button  
I START/STOP button  
J AIR FLOW DIRECTION  
VERTICAL SET button  
K AIR FLOW DIRECTION  
VERTICAL SWING button  
L AIR FLOW DIRECTION  
HORIZONTAL SET button  
M AIR FLOW DIRECTION  
HORIZONTAL SWING button  
N TIME ADJUST button  
O ACL button  
7 SWING Indicator Lamp (orange)  
(HORIZONTAL SWING)  
If the TIMER indicator lamp flashes when  
the timer is operating, it indicates that a  
fault has occurred with the timer setting  
(See page 16 Auto Restart).  
8 Intake Grille (Fig. 3)  
9 Air Filter  
0 UP/DOWN Air Direction Flaps  
A RIGHT/LEFT Air Direction Louvers  
(behind UP/DOWN Air Direction Flaps)  
B Drain Hose  
Rear side (Fig. 5)  
P TEST RUN  
Touch the two metal contacts with a me-  
tallic object to send the signal to perform  
a test run.  
Perform a test run only when installing the  
air conditioner. If the signal to perform a  
test run is received during normal opera-  
tion, the air conditioners thermostat will  
malfunction.  
If the signal to perform a test run is re-  
ceived during normal operation, the unit  
will switch to the test operation mode and  
the indoor units OPERATION and TIMER  
indicator lamps will flash simultaneously.  
To stop the test operation mode, press the  
START/STOP button to stop the air condi-  
tioner.  
Q Remote Control Unit Display (Fig. 6)  
R Transmit Indicator  
S Clock Display  
T Operating Mode Display  
U Timer Mode Display  
V Fan Speed Display  
W Temperature Set Display  
X Timer Set Indicator  
Y Temperature Set Indicator  
En-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
CAUTION!  
Load Batteries (R03/LR03/AAA × 2)  
Take care to prevent infants from  
accidentally swallowing batteries.  
When not using the remote control unit  
for an extended period, remove the  
batteries to avoid possible leakage and  
damage to the unit.  
Press and slide the battery compartment lid on the re-  
1
verse side to open it.  
Slide in the direction of the arrow while pressing the  
mark.  
If leaking battery fluid comes in contact  
with your skin, eyes, or mouth, immedi-  
ately wash with copious amounts of  
water, and consult your physician.  
Dead batteries should be removed  
quickly and disposed of properly, either  
by placing in a public battery collection  
receptacle, or by returning to appropri-  
ate authority.  
Insert batteries.  
2
3
Be sure to align the battery polarities (  
) correctly.  
Close the battery compartment lid.  
Do not attempt to recharge dry batteries.  
Never mix new and used batteries, or  
batteries of different types.  
Batteries should last about one year  
under normal use. If the remote control  
units operating range becomes appre-  
ciably reduced, replace the batteries and  
press the ACL button with the tip of a  
ballpoint pen or other small object.  
Set the Current time  
Press the TIME ADJUST button.  
1
2
Use the tip of a ball-point pen or other small object to press the button.  
Use the (  
) SET TIME buttons to adjust the clock  
to the current time.  
button: Press to advance the time.  
button: Press to reverse the time.  
(Each time the buttons are pressed, the time will be advanced/reversed in  
one-minute increments; hold the buttons depressed to change the time  
quickly in ten-minute increments.)  
Press the TIME ADJUST button again.  
This completes the time setting and starts the clock.  
3
To Use the Remote Control Unit  
The remote control unit must be pointed at signal receiver to operate correctly.  
Operating range: About 7 meters.  
When a signal is properly received by the air conditioner, a beeping sound will  
be heard.  
If no beep is heard, press the remote control unit button again.  
Remote Control Unit Holder  
Slide up  
Insert  
Press in  
Pull out  
Screws  
1
Mount the Holder.  
2
Set the Remote Control Unit.  
3
To remove the Remote  
Control Unit (when use at  
hand).  
En-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
Instructions relating to heating (*) are applicable only to HEAT & COOL MODEL(Reverse Cycle).  
To Select Mode Operation  
Press the START/STOP button.  
1
The indoor units OPERATION indicator lamp (red) will light.  
The air conditioner will start operating.  
Press the MASTER CONTROL button to select the de-  
2
sired mode.  
Each time the button is pressed, the mode will change in the following  
order:  
s
s
s
AUTO  
COOL  
DRY  
t
t
*HEAT  
FAN  
About three seconds later, the entire display will reappear.  
Example: When set to COOL  
To Set the Thermostat  
Press the SET TEMP. buttons.  
button: Press to rise the thermostat setting.  
button: Press to lower the thermostat setting.  
Thermostat setting range:  
AUTO .................................. 64 to 88 °F  
* Heating ............................... 60 to 88 °F  
Cooling/Dry ........................ 64 to 88 °F  
The thermostat cannot be used to set room temperature during the FAN mode (the  
temperature will not appear on the remote control units display).  
About three seconds later, the entire display will reappear.  
The thermostat setting should be considered a standard value, and may differ  
somewhat from the actual room temperature.  
Example: When set to 88 °F  
To Set the Fan Speed  
Press the FAN CONTROL button.  
Each time the button is pressed, the fan speed changes in the following order:  
s
AUTO  
s
HIGH  
s
s
MED  
LOW  
About three seconds later, the entire display will reappear.  
When set to AUTO:  
* Heating : Fan operates so as to optimally circulate warmed air.  
However, the fan will operate at very low speed when the temperature  
of the air issued from the indoor unit is low.  
Cooling : As the room temperature approaches that of the thermostat setting,  
the fan speed becomes slower.  
Fan  
: The fan alternately turns on and off; when on, the fan runs at the low  
fan speed.  
Example: When set to AUTO  
The fan will operate at a very low setting during Monitor operation  
and at the start of the Heating mode.  
To Stop Operation  
Press the START/STOP button.  
The OPERATION indicator lamp (red) will go out.  
En-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
Instructions relating to heating (*) are applicable only to HEAT & COOL MODEL(Reverse Cycle).  
About Mode Operation  
AUTO:  
COOLING MODEL  
When the room temperature is 4 °F higher  
than the set temperature, the mode will  
Cooling Operation  
switch between Cooling and Drying.  
Dry Operation  
During the Drying mode operation, the  
FAN setting should be switched to LOW  
Thermostat control  
for a gently cooling effect during which  
the fan may temporarily stop rotating.  
4 °F  
If the mode automatically selected by the  
unit is not satisfactory, see page 6 for in-  
Setting temperature  
structions on changing the mode setting  
(COOL, DRY, FAN).  
AUTO (* AUTO CHANGEOVER):  
HEAT & COOL MODEL (Reverse cycle)  
When AUTO CHANGEOVER is selected, the air conditioner selects the appropri-  
ate operation mode (Cooling or Heating) according to your rooms present tem-  
perature.  
When AUTO CHANGEOVER is first selected, the fan will operate at very low speed  
for about one minute while the unit determines the current conditions of the  
room and accordingly selects the proper operation mode.  
When the air conditioner has adjusted your rooms temperature to near the ther-  
mostat setting, it will begin monitor operation. In the monitor operation mode,  
the fan will operate at low speed. If the room temperature subsequently changes,  
the air conditioner will once again select the appropriate operation (Heating, Cool-  
ing) to adjust the temperature to the value set in the thermostat. (The monitor  
operation range is 4 °F relative to the thermostat setting.)  
If the mode automatically selected by the unit is not satisfactory, see page 6 for  
instructions on changing the mode setting (HEAT, COOL, DRY, FAN).  
*Heating:  
Use to warm your room.  
When Heating mode is selected, the air conditioner will operate at very low fan  
speed for about 3 to 5 minutes, after which it will switch to the selected fan set-  
ting. This period of time is provided to allow the indoor unit to warm up before  
beginning full operation.  
* During Heating mode:  
Set the thermostat to a temperature set-  
ting that is higher than the current room  
temperature. The Heating mode will not  
operate if the thermostat is set lower than  
the actual room temperature.  
When the room temperature is very low, frost may form on the outside unit, and  
its performance may be reduced. In order to remove such frost, the unit will  
automatically enter the defrost cycle from time to time. During Automatic De-  
frosting operation, the OPERATION indicator lamp (red) will flash, and the heat  
operation will be interrupted.  
During Cooling/Dry mode:  
Set the thermostat to a temperature set-  
ting that is lower than the current room  
temperature. The Cooling and Dry modes  
will not operate if the thermostat is set  
higher than the actual room temperature  
(in Cooling mode, the fan alone will oper-  
ate).  
Cooling:  
Use to cool your room.  
During Fan mode:  
The heat and cool functions of this unit  
cannot operate at the same time.  
Dry:  
Use for gently cooling while dehumidifying your room.  
You cannot heat the room during Dry mode.  
During Dry mode, the unit will operate at low speed; in order to adjust room  
humidity, the indoor units fan may stop from time to time. Also, the fan may  
operate at very low speed when detecting room humidity.  
The fan speed cannot be changed manually when Dry mode has been selected.  
Fan:  
Use to circulate the air throughout your room.  
En-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIMER OPERATION  
Before using the timer function, be sure that the Remote Control Unit is set to the correct current time (See page 5).  
To Use the ON timer or OFF timer  
To Cancel the Timer  
Press the START/STOP button  
Use the TIMER button to select TIMER  
1
RESET.  
(if the unit is already operating, proceed to step 2).  
The indoor units OPERATION indicator lamp (red) will light.  
The air conditioner will return to normal  
operation.  
Press the TIMER button to select the OFF timer or ON  
timer operation.  
Each time the button is pressed the timer function changes in the follow-  
To Change the Timer Settings  
2
Perform steps 2 and 3.  
To Stop Air Conditioner Operation  
while the Timer is Operating  
ing order:  
Press the START/STOP button.  
s
s
s
RESET  
OFF  
ON  
PROGRAM (OFF ON, OFF ON)t  
To Change Operating Conditions  
If you wish to change the operating  
conditions (Mode, Fan Speed, Thermostat  
Setting), after making the timer setting,  
wait until the entire display reappears, then  
press the appropriate buttons to change  
the operating condition desired.  
The indoor units TIMER indicator lamp (green) will light.  
Use the SET TIME buttons to adjust the desired OFF  
time or ON time.  
Set the time while the time display is flashing (the flashing will continue  
for about five seconds).  
3
button: Press to advance the time.  
button: Press to reverse the time.  
About five seconds later, the entire display will reappear.  
To Use the PROGRAM timer  
Press the START/STOP button  
To Cancel the Timer  
Use the TIMER button to select TIMER  
RESET.  
The air conditioner will return to normal  
operation.  
1
(if the unit is already operating, proceed to step 2).  
The indoor units OPERATION indicator lamp (red) will light.  
Set the desired times for OFF timer and ON timer.  
To Change the Timer Settings  
2
See the section To Use the ON timer or OFF timerto set the desired  
1. Follow the instructions given in the section  
To Use the ON Timer or OFF Timerto se-  
lect the timer setting you wish to change.  
mode and times.  
About three seconds later, the entire display will reappear.  
The indoor units TIMER indicator lamp (green) will light.  
2. Press the TIMER button to select either  
OFF ON or OFF ON.  
Press the TIMER button to select the PROGRAM timer  
To Stop Air Conditioner Operation  
while the Timer is Operating  
3
operation (either OFF ON or OFF ON will display).  
The display will alternately show OFF timerand ON timer, then change  
to show the time setting for the operation to occur first.  
Press the START/STOP button.  
To Change Operating Conditions  
The PROGRAM timer will begin operation. (If the ON timer has been  
selected to operate first, the unit will stop operating at this point.)  
If you wish to change operating conditions  
(Mode, Fan Speed, Thermostat Setting),  
after making the timer setting, wait until  
the entire display reappears, then press the  
appropriate buttons to change the operat-  
ing condition desired.  
About five seconds later, the entire display will reappear.  
About the PROGRAM timer  
About the ON timer  
The PROGRAM timer allows you to integrate OFF timer  
and ON timer operations in a single sequence. The se-  
quence can involve one transition from OFF timer to ON  
timer, or from ON timer to OFF timer, within a twenty-  
four hour period.  
The timer function is designed to bring your room to a  
comfortable temperature by the set time; as a result, the  
unit automatically begins operation before the set time  
so that the room reaches the desired temperature by the  
time set on the timer.  
The first timer function to operate will be the one set near-  
est to the current time. The order of operation is indicated  
by the arrow in the remote control units display (OFF →  
ON, or OFF ON).  
The hotter it is in summer, or the colder it is in winter, the  
earlier that operation will begin.  
* During Heating Operation ....... from 45 to 10 minutes be-  
fore set time.  
One example of PROGRAM timer use might be to have  
the air conditioner automatically stop (OFF timer) after  
you go to sleep, then start (ON timer) automatically in  
the morning before you rise.  
During Cooling/Dry Operation ... from 20 to 10 minutes be-  
fore set time.  
During Fan Operation .............. at the set time.  
En-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SLEEP TIMER OPERATION  
Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operate is stopped.  
To Use the SLEEP timer  
To Cancel the Timer:  
While the air conditioner is operating or stopped, press the  
Use the TIMER button to select “TIMER  
RESET”.  
SLEEP button.  
The air conditioner will return to normal  
operation.  
Both the indoor unit’s OPERATION indicator lamp (red) and the TIMER indicator  
lamp (green) will light.  
To Stop the Air Conditioner During  
Timer Operation:  
To Change the Timer Settings  
Press the START/STOP button.  
Press the SLEEP button once again and set the time using the  
SET TIME buttons.  
Set the time while the Timer Mode Display is flashing (the flashing will continue for  
about five seconds).  
button: Press to advance the time.  
button: Press to reverse the time.  
About five seconds later, the entire display will reappear.  
About the SLEEP timer  
To prevent excessive warming or cooling during sleep, the SLEEP timer function automatically modifies the thermostat setting  
in accordance with the time setting. When the set time has elapsed, the air conditioner completely stops.  
During Heating operation (HEAT & COOL MODEL (Reverse  
cycle) only):  
When the SLEEP timer is set, the thermostat setting is  
automatically lowered 2 °F every thirty minutes. When the  
thermostat has been lowered a total of 8 °F, the thermostat  
setting at that time is maintained until the set time has elapsed,  
at which time the air conditioner automatically turns off.  
During Cooling/Dry operation:  
When the SLEEP timer is set, the thermostat setting is auto-  
matically rised 2 °F every sixty minutes. When the thermostat  
has been rised a total of 4 °F, the thermostat setting at that  
time is maintained until the set time has elapsed, at which  
time the air conditioner automatically turns off.  
SLEEP timer setting  
SLEEP timer setting  
2 °F  
Set time  
1 hour  
4 °F  
6 °F  
8 °F  
30  
minutes  
1 hour  
4 °F  
2 °F  
1 hour  
30 minutes  
Set time  
MANUAL AUTO OPERATION  
Use the MANUAL AUTO operation in the event the remote control unit is lost or otherwise unavailable.  
CAUTION!  
How To Use the Main Unit Controls  
Do not press the MANUAL AUTO button with  
wet hands or pointed objects, otherwise an  
electric shock or malfunction may occur.  
Press the MANUAL AUTO button on the main unit control  
panel.  
To stop operation, press the MANUAL AUTO button once again.  
G When the air conditioner is operated  
with the controls on the Main unit, it  
will operate under the same mode as  
the AUTO mode selected on the re-  
mote control unit (see page 7).  
G The fan speed selected will be “AUTO”  
and the thermostat setting will be  
74 °F.  
En-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADJUSTING THE DIRECTION OF AIR CIRCULATION  
Instructions relating to heating (*) are applicable only to HEAT & COOL MODEL(Reverse Cycle).  
Vertical (up-down) direction of airflow is adjusted by pressing the remote control units AIR FLOW DIRECTION VERTICAL SET  
button. Horizontal (right-left) direction of airflow is adjusted by pressing the remote control units AIR FLOW DIRECTION  
HORIZONTAL SET button.  
DANGER!  
Vertical Air Direction Adjustment  
Never place fingers or foreign objects inside  
the outlet ports, since the internal fan oper-  
ates at high speed and could cause personal  
injury.  
Press the AIR FLOW DIRECTION VERTICAL SET button.  
Each time the button is pressed, the air direction range will change as follows:  
1
2
3
4
5
6
7
Always use the remote control units  
AIR FLOW DIRECTION button to adjust  
the UP/DOWN air direction flaps or  
RIGHT/LEFT air direction louvers. At-  
tempting to move them manually  
could result in improper operation; in  
this case, stop operation and restart.  
The louvers should begin to operate  
properly again.  
Types of Air flow Direction Setting:  
1,2,3,4  
5,6,7  
:
:
During Cooling/Dry Mode
* During Heating mode  
The remote control units display does  
not change.  
During use of the Cooling and Dry  
modes, do not set the UP/DOWN air  
direction flaps in the Heating range (5  
to 7) for long periods of time, since  
water vapor may condense near the  
outlet louvers and drops of water may  
drip from the air conditioner.  
Use the air direction adjustments within the ranges shown above.  
The vertical airflow direction is set automatically as shown, in accordance with  
the type of operation selected.  
During Cooling/Dry mode : Horizontal flow 1  
* During Heating mode  
: Downward flow 7  
When used in a room with infants, chil-  
dren, elderly or sick persons, the air  
direction and room temperature  
should be considered carefully when  
making settings.  
During AUTO mode operation, for the first minute after beginning operation,  
airflow will be horizontal 1; the air direction cannot be adjusted during this pe-  
riod.  
Horizontal Air Direction Adjustment  
Press the AIR FLOW DIRECTION HORIZONTAL SET button.  
Each time the button is pressed, the air direction range will change as follows:  
1
2
3
4
5
The remote control units display does  
not change.  
Example: When set to vertical air direc-  
RIGHT/LEFT air direction louvers  
tion  
Use the air direction adjustments within the ranges shown above.  
Example: When set to horizontal air di-  
rection  
Fig. 8  
En-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SWING OPERATION  
Begin air conditioner operation before performing this procedure.  
To select Vertical airflow SWING Operation  
Press the AIR FLOW DIRECTION VERTICAL SWING button.  
The SWING indicator lamp (VERTICAL SWING) (orange) will light.  
In this mode, the UP/DOWN air direction flaps will swing automatically to direct the  
air flow both up and down.  
To Stop Vertical airflow SWING Operation  
Press the AIR FLOW DIRECTION VERTICAL SWING button  
once again.  
The SWING indicator lamp (VERTICAL SWING) will go out.  
Airflow direction will return to the setting before swing was begun.  
Example: When set to vertical swing  
About Swing Operation  
G The range of swing is relative to the currently set airflow  
direction.  
G If the swing range is not as desired, use the remote con-  
trol unit’s AIR FLOW DIRECTION VERTICAL SET button to  
change the range of swing.  
Air flow direction set  
Range of swing  
1 to 3  
G The SWING operation may stop temporarily when the air  
conditioner’s fan is not operating, or when operating at  
very low speeds.  
1
2
3
4
5
6
7
1 to 4  
2 to 5  
3 to 6  
4 to 7  
G During use of the Cooling and Dry modes, do not set the  
air UP/DOWN direction flaps, in the Heating range (5 to  
7) for long periods of time, since water vapor may con-  
dense near the outlet louvers and drops of water may  
drip from the air conditioner.  
5 to 7  
1 to 7 (All range)  
Air direction range (See page 10, Fig. 7)  
To select Horizontal airflow SWING Operation  
Press the AIR FLOW DIRECTION HORIZONTAL SWING button.  
The SWING indicator lamp (HORIZONTAL SWING) (orange) will light.  
In this mode, the RIGHT/LEFT air direction louvers will swing automatically to direct  
the airflow both right and left.  
To Stop Horizontal airflow SWING Operation  
Press the AIR FLOW DIRECTION HORIZONTAL SWING button  
once again.  
The SWING indicator lamp (HORIZONTAL SWING) will go out.  
Airflow direction will return to the setting before swing was begun.  
Example: When set to horizontal swing  
About Swing Operation  
G The range of swing is relative to the currently set airflow  
direction.  
G If the swing range is not as desired, use the remote con-  
trol unit’s AIR FLOW DIRECTION HORIZONTAL SET but-  
ton to change the range of swing.  
Air flow direction set  
Range of swing  
1 to 5 (All range)  
1 to 3  
2 to 4  
3 to 5  
1 to 5 (All range)  
G The SWING operation may stop temporarily when the air  
conditioner’s fan is not operating, or when operating at  
very low speeds.  
1
2
3
4
5
Air direction range (See page 10, Fig. 8)  
En-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLEANING AND CARE  
Before cleaning the air conditioner, be sure to turn it off and disconnect the power supply cord.  
CAUTION!  
Be sure the intake grille is installed securely.  
When removing and replacing the air filters, be sure not to touch the heat exchanger, as per-  
sonal injury may result.  
Cleaning the Air Filter  
1. Pull out both sides and the center of the  
intake grille.  
4. Re-attach the air filters to the intake grille.  
1 The air filters fit onto the inside of the intake grille.  
(figure 1)  
2 The bottom edges of the air filters should fit into the  
filter brackets. (figure 1)  
3 The air filters should be pushed down so that their  
top edges fit under the projections at the top of the  
intake grille. (figure 2)  
About 30 mm  
(1-3/16)  
Air Filter  
Side Panel  
Hook  
(Figure 1)  
(Figure 2)  
Notch  
Arm  
Arm  
Intake Grille  
Filter bracket  
2. Pull the air filters upward to remove them.  
Push the air filter handles away from the intake grille in  
direction 1, then pull out the air filters.  
5. Push in both sides and the center of the  
intake grille.  
1
Air Filter  
Bracket  
Base  
Handle  
Intake Grille  
Dust can be cleaned from the air filter either with a vacuum  
cleaner, or by washing the filter in a solution of mild de-  
tergent and warm water. If you wash the filter, be sure to  
allow it to dry thoroughly in a shady place before rein-  
stalling.  
3. Clean the air filters.  
Remove the dust from the air filters by vacuuming or  
washing them. After washing, allow the air filters to dry  
thoroughly in an area protected from sunlight.  
If dirt is allowed to accumulate on the air filter, air flow  
will be reduced, lowering operating efficiency and increas-  
ing noise.  
During periods of normal use, the air filters should be  
cleaned every two weeks.  
When used for extended periods, the unit may accumulate dirt inside, reducing its performance. We recommend that the  
unit be inspected regularly, in addition to your own cleaning and care. For more information, consult authorized service  
personnel.  
When cleaning the units body, do not use water hotter than 104 °F, harsh abrasive cleansers, or volatile agents like  
benzene or thinner.  
Do not expose the unit body to liquid insecticides or hairsprays.  
If the unit will not be operated for a period of one month or more, be sure to allow the inner parts of the unit to dry  
thoroughly, in advance, by operating the unit in fan mode for half a day.  
En-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SELECTING THE REMOTE CONTROL UNIT SIGNAL CODE  
When two or more air conditioners are installed in a room and the remote control  
unit is operating an air conditioner other than the one you wish to set, change the  
signal code of the remote control unit to operate only the air conditioner you wish  
to set (four selections possible).  
When two or more air conditioners are installed in a room, please contact your  
retailer to set the individual air conditioner signal codes.  
To operate only  
one of multiple  
air conditioners  
Selecting the Remote Control Unit Signal Code  
Use the following steps to select the signal code of the remote control unit. (Note  
that the air conditioner cannot receive a signal code if the air conditioner has not  
been set for the signal code.)  
Press the START/STOP button until only the clock is  
displayed on the remote control unit display.  
1
Press the MASTER CONTROL button for at least five  
seconds to display the current signal code (initially set  
to ).  
2
Press the  
tween  
air conditioner signal code.  
buttons to change the signal code be-  
. Match the code on the display to the  
3
4
Press the MASTER CONTROL button again to return to  
the clock display. The signal code will be changed.  
If no buttons are pressed within 30 seconds after the signal code is displayed, the system returns to the original clock  
display. In this case, start again from step 1.  
The air conditioner signal code is set to A prior to shipment. Contact your retailer to change the signal code.  
The remote control unit resets to signal code A when the batteries in the remote control unit are replaced. If you use a  
signal code other than signal code A, reset the signal code after replacing the batteries.  
If you do not know the air conditioner signal code setting, try each of the signal codes (  
code which operates the air conditioner.  
) until you find the  
En-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
Instructions relating to heating (*) are applicable only to HEAT & COOL MODEL(Reverse Cycle).  
In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the  
power supply plug, and consult authorized service personnel.  
Merely turning off the units power switch will not completely disconnect the unit from the power  
source. Always be sure to disconnect the power supply plug or turn off your circuit breaker to  
ensure that power is completely off.  
WARNING!  
Before requesting service, perform the following checks:  
Symptom  
Problem  
See Page  
NORMAL  
FUNCTION  
Doesnt operate immedi-  
ately:  
If the unit is stopped and then immediately started again, the com-  
pressor will not operate for about 3 minutes, in order to prevent  
fuse blowouts.  
Whenever the power supply plug is disconnected and then recon-  
nected to a power outlet, the protection circuit will operate for about  
3 minutes, preventing unit operation during that period.  
Noise is heard:  
During operation and immediately after stopping the unit, the  
sound of water flowing in the air conditioners piping may be  
heard. Also, noise may be particularly noticeable for about 2 to 3  
minutes after starting operation (sound of coolant flowing).  
During operation, a slight squeaking sound may be heard. This is  
the result of minute expansion and contraction of the front cover  
due to temperature changes.  
*During Heating operation, a sizzling sound may be heard occa-  
sionally. This sound is produced by the Automatic Defrosting op-  
eration.  
15  
Smells:  
Some smell may be emitted from the indoor unit. This smell is  
the result of room smells (furniture, tobacco, etc.) which have  
been taken into the air conditioner.  
Mist or steam are  
emitted:  
During Cooling or Dry operation, a thin mist may be seen emitted  
from the indoor unit. This results from the sudden Cooling of room  
air by the air emitted from the air conditioner, resulting in con-  
densation and misting.  
*During Heating operation, the outdoor units fan may stop, and  
steam may be seen rising from the unit. This is due to the Auto-  
matic Defrosting operation.  
15  
Airflow is weak or stops:  
*When Heating operation is started, fan speed is temporarily very  
low, to allow internal parts to warm up.  
*During Heating operation, if the room temperature rises above  
the thermostat setting, the outdoor unit will stop, and the indoor  
unit will operate at very low fan speed. If you wish to warm the  
room further, set the thermostat to a higher setting.  
*During Heating operation, the unit will temporarily stop opera-  
tion (between 7 and 15 minutes) as the Automatic Defrosting mode  
operates. During the Automatic Defrosting operation, the OPERA-  
TION indicator lamp will flash.  
15  
The fan may operate at very low speed during Dry operation or  
when the unit is monitoring the rooms temperature.  
6
6
In the monitor AUTO operation, the fan will operate at very low  
speed.  
Water is produced from  
the outdoor unit:  
*During Heating operation, water may be produced from the out-  
15  
door unit due to the Automatic Defrosting operation.  
En-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
Instructions relating to heating (*) are applicable only to HEAT & COOL MODEL(Reverse Cycle).  
Symptom  
Items to check  
Has there been a power failure?  
See Page  
CHECK ONCE Doesnt operate at all:  
MORE  
Has a fuse blown out, or a circuit breaker been tripped?  
8 to 9  
Is the timer operating?  
Poor Cooling (or *Heating) Is the air filter dirty?  
performance:  
Are the air conditioners intake grille or outlet port blocked?  
Did you adjust the room temperature settings (thermostat) cor-  
rectly?  
Is there a window or door open?  
In the case of Cooling operation, is a window allowing bright sun-  
light to enter? (Close the curtains.)  
In the case of Cooling operation, are there heating apparatus and  
computers inside the room, or are there too many people in the  
room?  
The unit operates differ- Are the remote control units batteries dead?  
ently from the remote con-  
trol units setting:  
5
Are the remote control units batteries loaded properly?  
Signal is not received after Are you using an air conditioner signal code other than signal  
13  
replacing the batteries for  
the remote control unit:  
code A?  
If the problem persists after performing these checks, or if you notice burning smells, or the TIMER indicator lamp flashes, stop  
operation immediately, disconnect the power supply plug, and consult with authorized service personnel.  
OPERATING TIPS  
Instructions relating to heating (*) are applicable only to HEAT & COOL MODEL(Reverse Cycle).  
Operation and Performance  
*Heating Performance  
*Microcomputer-controlled Automatic Defrosting  
This air conditioner operates on the heat-pump principle,  
absorbing heat from outdoor air and transferring that heat  
indoors. As a result, the operating performance is reduced  
as outdoor air temperature drops. If you feel that insuffi-  
cient heating performance is being produced, we recom-  
mend you use this air conditioner in conjunction with  
another kind of heating appliance.  
When using the Heating mode under conditions of low  
outdoor temperature and high humidity, frost may form  
on the outdoor unit, resulting in reduced operating per-  
formance.  
In order to prevent this kind of reduced performance, this  
unit is equipped with a Microcomputer-controlled Auto-  
matic Defrosting function. If frost forms, the air condi-  
tioner will temporarily stop, and the defrosting circuit will  
operate briefly (for about 7 to 15 minutes).  
Heat-pump air conditioners heat your entire room by  
recirculating air throughout the room, with the result that  
some time may be required after first starting the air con-  
ditioner until the room is heated.  
During Automatic Defrosting operation, the OPERATION  
indicator lamp (red) will flash.  
*When Indoor and Outdoor Temperature are High  
*Low Ambient Cooling  
When both indoor and outdoor temperatures are high  
during use of the heating mode, the outdoor units fan  
may stop at times.  
When the outdoor temperature drops, the outdoor units  
fans may switch to Low Speed.  
En-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING TIPS  
AUTO Restart  
In Event of Power Interruption  
Should the power supply to the air conditioner be inter-  
rupted by a power failure, the air conditioner will restart  
automatically in the previously selected mode once the  
power is restored.  
Use of other electrical appliances (electric shaver, etc.) or  
nearby use of a wireless radio transmitter may cause the  
air conditioner to malfunction. In this event, temporarily  
disconnect the power supply plug, reconnect it, and then  
use the remote control unit to resume operation.  
Should a power failure occur during TIMER operation, the  
timer will be reset and the unit will begin (or stop) oper-  
ating under the new timer setting. In this event, the TIMER  
indicator lamp (green) will flash (see page. 4).  
Multi-type Air conditioner  
This indoor unit can be connected to a multi-type outdoor unit. The multi-type air conditioner allows multiple indoor units to  
be operated in multiple locations. The indoor units may be operated simultaneously, in accordance with their respective  
output.  
Simultaneous Use of Multiple Units  
Instructions relating to inverter ( ) are applicable only to INVERTER MODEL.  
Operation can be done in the following different operat-  
When using a multi-type air conditioner, the multiple  
indoor units can be operated simultaneously, but when  
two or more indoor units of the same group are oper-  
ated simultaneously, the heating and cooling efficiency  
will be less than when a single indoor unit is used alone.  
Accordingly, when you wish to use more than one in-  
door unit for cooling at the same time, the use should  
be concentrated at night and other times when less out-  
put is required. In the same way, when multiple units  
are used simultaneously for heating, it is recommended  
that they be used in conjunction with other auxiliary  
space heaters, as required.  
ing modes.  
Cooling mode and dry mode  
Cooling mode and fan mode  
Dry mode and fan mode  
The operating mode (heating mode or cooling (dry)  
mode) of the outdoor unit will be determined by the op-  
erating mode of the indoor unit that was operated first.  
If the indoor unit was started in fan mode, the operating  
mode of the outdoor unit will not be determined.  
For example, if indoor unit (A) was started in fan mode  
and then indoor unit (B) was then operated in heating  
mode, indoor unit (A) would temporarily start opera-  
tion in fan mode but when indoor unit (B) started oper-  
ating in heating mode, the OPERATION indicator lamp  
(red) for indoor unit (A) would begin to flash (1 second  
on, 1 second off) and it would go into standby mode.  
Indoor unit (B) would continue to operate in heating  
mode.  
Seasonal and outdoor temperature conditions, the struc-  
ture of the rooms and the number of persons present  
may also result in differences of operating efficiency.  
We recommend that you try various operating patterns  
in order to confirm the level of heating and cooling out-  
put provided by your units, and use the units in the way  
that best matches your family's lifestyle.  
If you discover that one or more units delivers a low  
level of cooling or heating during simultaneous opera-  
tion, we recommend that you stop simultaneous opera-  
tion of the multiple units.  
Operation cannot be done in the following different op-  
erating modes.  
If the indoor unit is instructed to do an operating mode  
that it cannot perform, the OPERATION indicator lamp  
(red) on the indoor unit will flash (1 second on, 1 sec-  
ond off) and the unit will go into the standby mode.  
Heating mode and cooling mode (or dry mode)  
Heating mode and fan mode  
En-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING TIPS  
Notice  
Instructions relating to heating (*) are applicable only to HEAT & COOL MODEL(Reverse Cycle).  
*During use of the heating mode, the outdoor unit will  
occasionally commence the defrost operation for brief  
periods. During the defrosting operation, if the user sets  
the indoor unit for heating again, the defrosting mode  
will continue, and the heating operation will begin after  
completion of defrosting, with the result that some time  
may be required before warm air is emitted.  
*During use of the heating mode, the top of the indoor  
unit may become warm, but this is due to the fact that  
coolant is circulated through the indoor unit even when  
it is stopped; it is not a malfunction.  
En-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Cisco Systems Network Router 1417 User Manual
Cornelius Door Door Latch User Manual
Craftsman Lawn Mower Accessory 48624598 User Manual
Curtis DVD VCR Combo DVD7802 User Manual
Danby Freezer DCR033A1BSLDD User Manual
Danby Refrigerator DFF1044W BLS User Manual
Fellowes Paper Shredder H 6C User Manual
Fisher Paykel Garbage Disposal GD75IA1 User Manual
Fisher Price Automobile Accessories G5911 User Manual
Frigidaire Blender 900253211 UM User Manual