Fisher Price Automobile Accessories G5911 User Manual

Infant-to-Toddler Rocker  
Toddler Seat  
Infant Seat  
Model Number: G5911  
WARNING  
IMPORTANT! KEEP INSTRUCTIONS  
FOR FUTURE REFERENCE.  
Please keep this instruction sheet, as it contains important information.  
Use the upright position only when your child has developed enough upper body control to sit without leaning forward.  
Always use the restraint until your child is able to climb in and out of the chair unassisted.  
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).  
Requires one LR20 "D" alkaline battery (not included) for vibrations unit operation.  
c
i
f
w
w
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
IMPORTANT! Before assembly, inspect this product for  
damaged hardware, loose joints, missing parts or sharp  
edges. DO NOT use if any parts are missing or broken.  
Contact Mattel for replacement parts and instructions  
if needed. Never substitute parts.  
#8 x 1.9 cm (3/4") Screw  
Shown Actual Size  
Cross  
Brace  
CAUTION  
This package contains small parts  
in its unassembled state.  
Adult assembly is required.  
2
Side  
Rails  
• Insert a screw through the hole in the bottom of each side  
rail and into the cross brace. Tighten the screws with a  
Phillips screwdriver. Do not over-tighten.  
Cross Brace  
Button  
Push  
Seat Back Tube  
Push  
Side Rails  
1
• Position each side rail so that the button faces outward.  
• Fit the cross brace between the side rails, as shown.  
• Push the cross brace down to “snap” it into place. This may  
require a lot of force.  
3
• Insert the seat back tube into the socket in each side rail.  
• While pressing the tabs on the ends of the seat back tube,  
continue to insert the seat back tube into the sockets in  
each side rail, until the tabs “snap” into place. Make sure  
you hear a “snap” on each side.  
• Pull the seat back tube up to be sure it is secure in the  
side rail sockets.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Side  
Rail  
Side Rail  
Hole  
Front Tube  
Side  
Rail  
Front Tube  
Vibrations  
Unit  
Side Rail  
Hole  
5
4
#8 x 3 cm (11/8") Screw  
Shown Actual Size  
(1  
1/8")  
• Locate the hole in each side rail.  
• Insert a #8 x 3 cm  
screw through the  
outside of each side rail and  
• With the vibrations unit facing forward, fit the front tube  
to the side rails, as shown. Hold the front tube in place  
and proceed to step 5.  
into the ends of the front tube.  
IMPORTANT! Please follow the next assembly (step 6)  
carefully to completely secure the front tube to the  
side rails.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Retainer  
with Lock Nut  
Kickstand  
Press  
Tab  
Press  
Tab  
Rounded Side  
6
Receptacles  
7
M4 Lock Nut - 2  
(Inside Retainer)  
• Fit a retainer with lock nut  
onto the end of the screw  
and to the inside of a  
side rail.  
Shown Actual Size  
• Position the assembly face down, as shown.  
• While pressing the tab on each end of the kickstand,  
insert the kickstand into the receptacle in each side rail,  
as shown.  
• Push the kickstand into the receptacles until the  
tabs “snap” into place. Make sure you hear a “snap” on  
each side.  
Hint: A lock nut has been factory assembled to the retainer.  
During shipment, the lock nut may have fallen out of the  
retainer. If it has, please fit it into the hexagonal hole in the  
retainer so that the rounded side of the lock nut faces out.  
• Pull the kickstand to be sure it is secure in the receptacles.  
• Tighten the screw with a Phillips screwdriver. Do not  
over-tighten.  
• Repeat this procedure to fasten the screw in the other  
end of the front tube and side rail, using the remaining  
retainer with lock nut.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Pad  
Pad Slot  
Press  
Seat Back  
Seat Back  
Tube  
Hardboard  
8
9
Side  
Rail  
• Turn the assembly upright.  
• Fit the upper pocket on  
the pad onto the seat  
back tube.  
• Fasten the pad buckles  
around each side rail.  
• Turn the hardboard  
over and insert it into  
the slot in the front  
Pad  
Buckles  
edge of the pad.  
• Fasten the pad buckles on  
the front edge of the pad  
Pad  
Buckles  
and underneath the seat. Make sure you hear a “snap” on  
both sides.  
• Press the fasteners together in the seat back portion of  
the pad.  
Assembly is now complete.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Battery Installation  
Battery Safety Information  
1.5V  
LR20 "D"  
+
SHOWN ACTUAL SIZE  
Batteries may leak fluids that can cause a chemical burn  
injury or ruin your product. To avoid battery leakage:  
• Do not mix old and new batteries or batteries of different  
types: alkaline, standard (carbon-zinc) or rechargeable  
(nickel-cadmium).  
Battery  
Compartment  
• Insert batteries as indicated inside the battery compartment.  
• Remove batteries during long periods of non-use. Always  
remove exhausted batteries from the product. Dispose  
of batteries safely. Do not dispose of batteries in a fire.  
The batteries may explode or leak.  
• Locate the battery compartment on the bottom of the  
vibrations unit.  
• Loosen the screw in the battery compartment door with a  
Phillips screwdriver.  
• Lift to remove the battery compartment door.  
• Insert one LR20 "D" alkaline battery as indicated inside  
the battery compartment.  
• Never short-circuit the battery terminals.  
• Use only batteries of the same or equivalent type,  
as recommended.  
• Do not charge non-rechargeable batteries.  
• Remove rechargeable batteries from the product  
before charging.  
Hint: We recommend using an alkaline battery for longer  
battery life.  
• If removable, rechargeable batteries are used, they are only  
to be charged under adult supervision.  
• Replace the battery compartment door and tighten the  
screw with a Phillips screwdriver. Do not over-tighten.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Set-Up & Use  
Securing Your Infant  
IMPORTANT! Before each use, inspect this product for  
damaged hardware, loose joints, missing parts or sharp  
edges. DO NOT use if any parts are missing or broken.  
Contact Mattel for replacement parts and instructions if  
needed. Never substitute parts.  
WARNING  
To prevent serious injury or death:  
• Always use the restraint until child  
is able to climb in and out of the  
chair unassisted.  
• It is dangerous to use this product  
on an elevated surface.  
• Never leave child unattended.  
WARNING  
To prevent serious injury or death:  
Use the upright position only when child  
has developed enough upper body  
control to sit without leaning forward.  
Seat Position  
Restraint  
Restraint  
Belt  
Lower  
Belt  
Lift  
Press  
Button  
Press  
Button  
Restraint  
Pad  
1
Recline  
Upright  
Select a seat position for your childs comfort:  
Upright or Recline.  
2
Upright  
While pressing the button on each side rail, lift the seat back.  
• Place your child in the seat. Position the restraint pad  
between your child’s legs.  
Recline  
While pressing the button on each side rail, lower the  
seat back.  
• Fasten the restraint belts to each side of the restraint pad.  
Make sure you hear a “click” on both sides.  
• Check to be sure the restraint system is securely attached  
by pulling it away from your child. The restraint system  
should remain attached.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Securing Your Infant  
Toys  
Anchored End  
Anchored End  
Strap  
B
Strap  
Strap  
B
Toy  
Free End  
Toy  
Free End  
3
Loosen  
Tighten  
To tighten the belts:  
• Feed the anchored end of the restraint belt up through the  
buckle to form a loop  
• Pull the free end of the restraint belt  
• Repeat this procedure to tighten the other restraint belt.  
To loosen the belts:  
.
4
B
.
Toy  
• Feed the free end of the restraint belt up through the  
buckle to form a loop . Enlarge the loop by pulling on  
the end of the loop toward the buckle.  
• Fit the pad straps through  
the slot in the toy rings.  
Fasten the straps.  
• Or, attach the toys to the  
toy bar straps (please see  
Step 5).  
• Pull the anchored end of the restraint belt to shorten the  
B
free end of the restraint belt  
.
• Repeat this procedure to loosen the other restraint belt.  
Hint: Pull the monkey’s head for a short tune.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Toy Bar  
Calming Vibrations  
Toy Bar  
Plug  
Plug  
6
Toys  
Power Switch  
• Make sure your child is properly secured in the seat.  
• Slide the power switch to the on position for  
calming vibrations.  
• Slide the power switch to the off position to turn  
vibrations off.  
5
• Fit the plugs on each end  
of the toy bar into the  
sockets in each side rail.  
• Fit the toy bar straps  
through the slot in the toy  
rings. Fasten the straps.  
• Or, attach the toys to the  
pad straps (see Step 4).  
Hint: Pull the monkey’s head for a short tune.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Kickstand  
Storing the Restraint  
System for Toddler Use  
Small Slot  
Small  
Slot  
Large  
Slot  
7
Kickstand  
8
• Rotate the kickstand out.  
• Push down on the seat bottom to be sure the kickstand  
is in position.  
• Insert the restraint belts back through the small slots in  
the pad.  
• Insert the restraint pad down through the large slot in  
the pad.  
9
• Turn the rocker face down.  
• Tuck the ends of the restraint pad underneath the buckles,  
as shown.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care  
The frame, pad toy bar and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach.  
Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue.  
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.  
©2004 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.  
PRINTED IN CHINA  
G5911pr-0726  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Craftsman Lawn Mower Accessory 91724903 User Manual
Craftsman Pressure Washer 91976902 User Manual
Crown Audio Stereo Amplifier SST SBSC 3632T User Manual
Earthquake Sound Speaker HoLeeS 15 User Manual
Euro Pro Carpet Cleaner SC618HD User Manual
Exergen Scanner DT 1001 User Manual
Fender Mixer SRM 6302 User Manual
Fisher Price Motorized Toy Car X3419 User Manual
Glen Dimplex Home Appliances Ltd Cooktop CTC60 User Manual
Global Machinery Company Drill BN18SB User Manual