User’s Manual
DVI DL 201 Tx/Rx
Dual Link DVI Transmitter and Receiver
68-1531-01
Rev. B
12 08
Download from Www.Somanuals.com. All Manuals Search And Download.
警告
安全须知 • 中文
这个符号提示用户该设备用户手册中
电源 • 该设备只能使用产品上标明的电源。 设备
必须使用有地线的供电系统供电。 第三条线
（地线）是安全设施，不能不用或跳过。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后
或桌面电源的电源线，或任何接到市电系统的电源线。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴
露的危险电压，有触电危险。
维护 • 所有维修必须由认证的维修人员进行。 设备内部
没有用户可以更换的零件。为避免出现触电危险不要自
己试图打开设备盖子维修该设备。
注意
阅读说明书 • 用户使用该设备前必须阅读并理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用
与厂家推荐的相同或相近型号的电池。 按照生产厂的
建议处理废弃电池。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备，以避免危险。
声明
所使用电源为 A 级产品，在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用
户对其干扰采取切实可行的措施。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
N
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide — DVI DL 201 Tx/Rx
The DVI DL 201 Tx/Rx extends DVI-D signals up to 100' (30 m) at
resolutions up to 2560x1600 @ 60 Hz, using twisted pair (TP) cable.
Install, connect, and operate the DVI DL 201 Tx/Rx as follows:
Step 1
Turn off all equipment or disconnect it from power sources. Mount
the transmitter and receiver as desired (see page 2-2).
Step 2
Determine how the source device will obtain the EDID information
and perform one of the following procedures:
To capture the EDID of a desired display and store it in
the EDID Minder for future use:
a.
Connect the display to the local monitor output of
the transmitter.
b.
c.
Power on the transmitter and the local monitor.
Configure the DDC switches as shown in the figure
at right and described on page 3-2.
Press and release the EDID "Store" button (see
the figure at right). The rear panel LED turns
amber while the EDID information is read and
stored from the local monitor. Afterwards, the
LED turns green.
ON
ON
1
2
3
OFF
d.
EDID
STORE
e.
Power off and disconnect the display from the
transmitter.
f.
g.
h.
Connect the transmitter to the receiver.
Connect a source device to the transmitter.
Connect a display device to the receiver and, if required, a local
monitor to the transmitter.
i.
j.
Power on the display device(s), the transmitter, and the receiver.
Power on the source device.
To use the default EDID (2560x1600 @ 60 Hz):
a.
Configure the DDC switches as shown in the figure
at right and described on page 3-3.
ON
ON
b.
c.
Connect a source device to the transmitter.
Connect a display device to the receiver and, if
required, a local monitor to the transmitter.
Connect the transmitter and receiver.
1
2
3
OFF
d.
e.
Power on the transmitter, receiver, and display devices.
f.
Power on the source device.
DVI DL 201 Tx/Rx • Quick Start Guide
QS-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide — DVI DL 201 Tx/Rx, cont’d
To use DDC pass-through routed to the local monitor:
a.
Configure the DDC switches as shown in the figure
at right and described on page 3-4.
Connect a source device to the transmitter.
Connect a display device to the receiver and, if
required, a local monitor to the transmitter.
Connect the transmitter and receiver.
Power on the transmitter, receiver, and local
monitor.
b.
c.
ON
ON
d.
e.
1
2
3
OFF
f.
Power on the source device.
g.
Power on the display device.
To use DDC pass-through routed to the remote display:
a.
Configure the DDC switches as shown in the figure
at right and described on page 3-5.
Connect a source device to the transmitter.
Connect a display device to the receiver and, if
required, a local monitor to the transmitter.
Connect the transmitter and receiver.
Power on the transmitter, receiver, and display
devices.
b.
c.
ON
ON
d.
e.
1
2
3
OFF
f.
Power on the source device.
If there are any problems, consult the troubleshooting section
(page 3-6).
N
Extron
DVI DL 201 Rx
DVI Dual Link
Receiver
Twisted Pair
Cables (3) 100’
L
O
H
R
T
T
S
U
N
S
R
O
C
P
x
R
A
x
T
S
Extron
0
DVI-D
DVI DL 201 Rx SERIE
DVI DL 201 Tx
DVI Dual Link
Transmitter
3
OUTPUT
2
1
DVI Dual Link
T
DO NO
S
CONNECT
N
OUTPUT
OUTPUT
LA
O
T
LOCAL
VI-D INP
D
U
E
R
RS-232
SS-TH
UT
O
R
A
TE
P
DDC
R
REMO
WE
PO
12V
X
0.4A MA
LOCAL
ARE
SP
High Resolution
Projector with
Dual Link Input
Local Monitor
PC with Dual Link
DVI Output
DVI DL 201 Tx/Rx • Quick Start Guide
QS-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter One • Introduction.................................................... 1-1
About this Manual .................................................................... 1-2
About the DVI DL 201 Tx/Rx.................................................. 1-2
DVI DL 201 Tx/Rx Features ..................................................... 1-2
Chapter Two • Installation ...................................................... 2-1
Mounting the DVI DL 201 Tx/Rx........................................... 2-2
Tabletop placement ............................................................... 2-2
Rack mounting....................................................................... 2-2
UL guidelines for rack mounting...........................................2-2
Rack mounting procedures....................................................2-3
Under-desk mounting............................................................ 2-4
Through-desk mounting........................................................ 2-5
Pole mounting........................................................................ 2-6
Panel Features............................................................................. 2-8
DVI DL 201 Tx front panel features ...................................... 2-8
DVI DL 201 Tx rear panel features........................................ 2-9
DVI DL 201 Rx front panel features.................................... 2-10
DVI DL 201 Rx rear panel features...................................... 2-11
Cable Connections and Switches ....................................... 2-12
DVI-D input........................................................................... 2-12
DVI-D output........................................................................ 2-12
Twisted pair output/input................................................... 2-14
Terminating shielded cable..................................................2-14
Connections ..........................................................................2-15
Single Link/Dual Link DVI ....................................................2-16
DDC switches........................................................................ 2-17
Control pass-through........................................................... 2-18
RS-232 signals.......................................................................2-19
IR signals ...............................................................................2-19
Power input.......................................................................... 2-20
DVI DL 201 Tx/Rx • Table of Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont’d
Chapter Three • Configuration and Operation......... 3-1
Configuration.............................................................................. 3-2
Using the EDID Minder to read and store EDID from a
displaꢀ..................................................................................... 3-2
Using the EDID Minder with the default EDID .................... 3-3
Using pass-through mode with DDC routed to a local
monitor................................................................................... 3-4
Using pass-through mode with DDC routed to the remote
displaꢀ..................................................................................... 3-5
Setup.............................................................................................. 3-6
Troubleshooting......................................................................... 3-6
Appendix A • Reference Information ............................A-1
Specifications..............................................................................A-2
Included Parts .............................................................................A-5
Optional Accessories ................................................................A-5
All trademarks mentioned in this manual are the properties of their respective owners.
68-1531-01
Rev. B
12 08
DVI DL 201 Tx/Rx • Table of Contents
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI DL 201 Tx/Rx
Chapter One
1
Introduction
About this Manual
About the DVI DL 201 Tx/Rx
DVI DL 201 Tx/Rx Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About this Manual
This manual contains information about the DVI DL 201 Tx/Rx
signal transmitter and receiver, with information on how to
mount, install, and operate these units.
In this manual, unless otherwise specified, the terms
"DVI DL 201" or "DVI DL 201 Tx/Rx" refer to both the
transmitter (DVI DL 201 Tx) and the receiver (DVI DL 201 Rx).
The term "transmitter" refers to the DVI DL 201 Tx, and
"receiver" refers to the DVI DL 201 Rx.
About the DVI DL 201 Tx/Rx
The DVI DL 201 Tx and DVI DL 201 Rx are dual link DVI
transmitter/receiver units. They can be purchased as a pair or
as individual units.
Each purchased pair and each individual unit is shipped with a
single external desktop 12 VDC power supply. A single power
supply, connected to the transmitter, is able to power both
devices.
Using three CAT 5/5e/6/7 twisted pair cables, DVI-D signals
can be extended up to 100' (30 m) at resolutions up to 2560 x
1600 @ 60 Hz. This is significantly further than the 15' (5 m)
specified for standard dual link DVI cables.
The DVI DL 201 Tx/Rx works with unshielded twisted
pair (UTP) cable or shielded twisted pair (STP) cable.
However, STP cables are required to ensure FCC Class A
and CE compliance.
N
DVI DL 201 Tx/Rx Features
Transmits dual link DVI-D signals over three CAT 5/5e/6/7
cables — Standard twisted pair cables provide an economical,
easily installed cable solution.
Long distance transmission — Signals are transmitted up to
100' (30 m), which is significantly further than the 15' (5 m)
specified for standard dual link DVI cables.
Local monitor output — The transmitter has a DVI-D output for
connection to a local monitor.
DDC routing to local or remote display — A two pole switch
allows the user to determine whether DDC signals are routed to
the local or the remote display device.
DVI DL 201 Tx/Rx • Introduction
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
EDID Minder — The EDID Minder maintains continuous EDID
(Extended Display Identification Data) communication with
the attached source. This ensures that the DVI source powers
up correctly and maintains a proper video output, even if the
display is off.
Control communications pass-through — The DVI DL 201
passes through RS-232 (two way) or IR (one way) control
signals, to a remote display.
Compact design — The transmitter is 1U high, a half rack wide
and 3" deep, for easy rack mounting near the source device.
The receiver is 1" high, a quarter rack wide and 3" deep,
allowing multiple mounting options near the display device.
Remote powering of receiver — A single power supply,
connected to the transmitter, is able to power both the
transmitter and receiver.
Extron
DVI DL 201 Tx
CAT 5/5e/6/7 Cables
up to 200 feet
Dual Link DVI
Transmitter
3
2
1
T
DO NO
NECT
S
CON
N
OUTPUT
LA
O
T
TPUT OUT
LOCAL
T
U
I-D INP
V
D
232
THR
U
E
RS-
SS-
UT
O
R
A
TE
MO
P
DDC
R
RE
WE
PO
12V
0.4A MAX
L
LOCA
E
AR
SP
RS-232
Local
Monitor
Control
System
PC w/ Dual Link DVI
Output
L
O
H
R
T
x
T
S
R
U
R
N
S
O
C
P
A
x
T
RS-232
DVI DL 201 Rx
UT
DVI-D
Extron
DVI DL 201 Rx
Dual Link
DVI Cable
Dual Link DVI
Receiver
2560 x 1600 Flat Panel
Display with Dual-Link
DVI Input
Typical Application for the DVI DL 201 Tx/Rx
DVI DL 201 Tx/Rx • Introduction
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction, cont’d
DVI DL 201 Tx/Rx • Introduction
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI DL 201 Tx/Rx
Chapter Two
2
Installation
Mounting the DVI DL 201 Tx/Rx
Panel Features
Cable Connections and Switches
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Mounting the DVI DL 201 Tx/Rx
The transmitter is 1U high, a half rack wide and 3" deep, for
easy rack mounting near the source device.
The receiver is 1" high, a quarter rack wide and 3" deep,
allowing multiple mounting options near the display device.
Tabletop placement
Attach the four included rubber feet to the bottom of the unit
and place it in any convenient location.
Rack mounting
UL guidelines for rack mounting
The following Underwriters Laboratories (UL) guidelines are
relevant to the safe installation of the DVI DL 201 Tx/Rx in a
rack:
1.
Elevated operating ambient temperature — If the unit
is installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment
may be greater than room ambient temperature. Therefore,
install the equipment in an environment compatible with
the maximum ambient temperature (Tma: +122 °F, +50 °C)
specified by Extron.
2.
3.
4.
Reduced air flow — Install the equipment in the rack
so that the equipment gets adequate air flow for safe
operation.
Mechanical loading — Mount the equipment in the rack
so that uneven mechanical loading does not create a
hazardous condition.
Circuit overloading — Connect the equipment to
the supply circuit and consider the effect that circuit
overloading might have on overcurrent protection and
supply wiring. Give appropriate consideration to the
equipment nameplate ratings when addressing this
concern.
5.
Reliable earthing (grounding) — Maintain reliable
grounding of rack-mounted equipment. Pay particular
attention to supply connections other than direct
connections to the branch circuit (such as the use of power
strips).
DVI DL 201 Tx/Rx • Installation
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Rack mounting procedures
The unit can be mounted in the front or rear of:
•
•
•
•
RSU 126 (6" deep 1U universal rack shelf kit: PN 60-190-10)
RSB 126 (6" deep 1U basic rack shelf: PN 60-604-10)
RSU 129 (9.5" deep 1U universal rack shelf kit: PN 60-190-01)
RSB 129 (9.5" deep 1U basic rack shelf: PN 60-604-01)
To mount the unit, follow these instructions:
1. Remove rubber feet if these have been installed on the
bottom of the unit.
2. Align the unit on the shelf and secure it to the shelf with
two 4-40 x 3/16" screws in diagonally opposite corners (see
the figure below, which shows installation using the
RSU 129 shelf).
3. Install false faceplate(s) or other unit(s) to the rack shelf.
4. Attach the shelf to the rack with the four provided
10-32 x 3/4" bolts
1U Universal Rack Shelf
1/2 Rack Width Front False
Faceplate
Front false
faceplate
uses 2
screws.
(2) 4-40 x 3/16"
Screws
Use 2 mounting holes on
opposite corners.
Installing the DVI DL 201 Tx on a rack shelf
DVI DL 201 Tx/Rx • Installation
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Under-desk mounting
The figure below shows how to mount the DVI DL 201 Tx under
a desk or podium, using the optional Extron MBU 123 under
desk mounting kit (PN 70-212-01). To mount the
DVI DL 201 Rx, the optional Extron MBU 125 under desk
mounting kit (PN 70-077-01, not shown) must be used. For
either unit, follow these instructions:
1.
Remove rubber feet if these have been installed on the
bottom of the unit.
2.
Secure the mounting brackets to the unit, using the four
4-40 screws provided (see the figure below).
Under-desk mounting the DVI DL 201 Tx
3.
4.
5.
Hold the unit with the brackets attached against the
underside of the table or other furniture. Mark the location
of the screw holes of the bracket on the mounting surface.
Drill four pilot holes, each 3/32" (2 mm) in diameter by
1/4" (6.3 mm) deep in the mounting surface at the marked
screw locations.
Insert #8 wood screws into the four pilot holes. Tighten
each screw into the mounting surface until just less than
1/4" (6.3 mm) of the screw head protrudes.
6.
7.
Guide the mounting screws through the slots in the
brackets and place the unit tight against the surface.
Slide the unit slightly in or out so that it is held in place
by the screws; tighten all four screws to secure the unit in
place (see the figure above).
DVI DL 201 Tx/Rx • Installation
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Through-desk mounting
The DVI DL 201 Tx should not be mounted through a desk.
To mount the DVI DL 201 Rx through a desk or podium, use
the optional Extron MBD 129 through-desk mounting kit
(PN 70-077-02), and follow these instructions:
1.
Remove rubber feet if these have been installed on the
bottom of the unit.
2.
Attach the brackets to the receiver, using the four 4-40
screws provided; leave the screws slightly loose.
Through-desk mounting the DVI DL 201 Rx
3.
4.
5.
Hold the unit in position under the mounting surface.
Mark the location of the four screw holes and the
mounting hole to be cut in the table.
Cut away the table material. Test the fit by inserting the
front of the device through the hole. If necessary, use a
rasp or coarse file to enlarge the hole.
Hold the receiver, with the brackets attached, in position
and mark the location of the holes in the brackets. Drill
four pilot holes, each 3/32" (2 mm) in diameter by 1/4"
deep (6.3 mm) deep.
6.
7.
8.
Attach the brackets to the mounting surface, using the four
#8 wood screws provided with the kit.
Slide the device in or out until the front panel is flush with
the table surface. Tighten the screws installed in step 2.
If the screws are inaccessible to a screwdriver, mark the
location of the unit relative to the brackets, remove the unit
and brackets, tighten the screws holding the brackets and
replace the unit as described in step 6.
DVI DL 201 Tx/Rx • Installation
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Pole mounting
The instructions for mounting the receiver on the projector pole,
using the PMK 300 pole mounting kit (PN 70-374-01), are shown
below. For instructions on using any other Extron projector
mounting kit, consult the appropriate user guide.
1.
If necessary, remove the rubber feet from the bottom of the
DVI DL 201 Rx.
2.
Mount the receiver to any of the bracket's three mounting
plates. The unit should be vertically mounted with the
front panel (DVI output) facing towards the projector and
the rear panel (RJ-45 slots) facing towards the ceiling.
Backing
Brace
Rubber Pad
U-Bolt
Clamping
Plate
Extron
PMK 300
Multi Product Projector
Mount Kit
Projector mounting the DVI DL 201 Rx
DVI DL 201 Tx/Rx • Installation
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
On the side mounting plates, the device is typically
mounted on the outside of the bracket. On the front
mounting plate, the device is mounted on the inside of
the bracket.
N
a. Use the two 4-40 x 3/16" screws (provided) to secure
the receiver to the bracket
b. If required, secure the power supply using the plastic
ties provided with the kit.
The projector pole can be clamped to the back surface of
the clamping plate on the PMK 300, as shown in the
figure on the previous page.
N
Alternatively, the PMK 300 has a hole in the bottom
plate that allows the projector pole to be inserted through
the center of the plate. In this configuration, slide the
PMK 300 up from the bottom of the pole before the
projector is installed.
3.
4.
Attach the rubber pad to the surface of the clamping plate
that will be in contact with the pole.
Place the U-bolt around the projector pole and insert the
two ends through the slotted holes in the clamping plate
and then through the round holes in the backing brace.
The provided U-bolt fits a pole with an external diameter
of 1.5" to 2.0". For larger or smaller diameter poles,
obtain a U-bolt from a local hardware store. The slotted
holes in the clamping plate can accommodate U-bolts
that are 1.0" to 2.5" in width.
N
5.
Secure the bracket to the projector pole with the U-bolt and
the provided hex nuts and washers. Use an appropriately-
sized socket wrench to tighten the hex nuts.
DVI DL 201 Tx/Rx • Installation
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Panel Features
DVI DL 201 Tx front panel features
The illustration below shows the front panel features of the
DVI DL 201 Tx.
DVI DL 201 Tx
DVI DUAL LINK TRANSMITTER
1
DVI DL 201 Tx front panel features
LED — An amber light indicates that the DVI DL 201 Tx is
receiving power from a power supply or remotely, through
the receiver. A green light indicates that the transmitter is also
receiving a video signal.
a
DVI DL 201 Tx/Rx • Installation
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI DL 201 Tx rear panel features
The illustration below shows the rear panel features of the
DVI DL 201 Tx.
DVI DL 201 Tx
SN XXXXXXXX
DVI DL TX
E
XXXXX 00/00
DO NOT CONNECT
OUTPUTS TO LAN
OUTPUTS
2
POWER
12V
0.4A MAX
1
3
CONTROL
LOCAL OUTPUT
DVI-D INPUT
EDID
STORE
PASS THRU
ON
ON
Tx Rx
1
2
3
OFF
2
3
4
5
6
7
8
DVI DL 201 Tx rear panel features
Power input — The 12 VDC power supply (provided) connects
to this two-pole, 3.5 mm captive screw connector.
b
c
d
e
DVI-D input — One female DVI-I connector accepts a dual-link
DVI-D input from the source device.
Local monitor output — One female DVI-I connector provides a
dual-link DVI-D output to the local monitor.
EDID Minder Store switch and LED — When depressed, the
transmitter reads and stores the EDID information from the local
monitor. The LED gives the status of this process.
DDC route switches — Three DIP switches allow the unit to be
configured to use the EDID Minder or route the DDC directly to
the display.
f
g
h
Control signal pass-through — A three-pole, 3.5 mm captive
screw connector inputs pass-through RS-232 (two-way) or IR
signals (one-way).
Twisted pair outputs — Three RJ-45 jacks are used for
transmitting DVI video, remote power, and communications/
control signals.
The DVI DL 201 transmits high frequency signals via
these TP outputs. Connections between the transmitter
and receiver must be point to point. It is recommended
that there should be no couplers, adapter, or patch panels
between the transmitter and receiver units.
N
DVI DL 201 Tx/Rx • Installation
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
DVI DL 201 Rx front panel features
The illustration below shows the front panel features of the
DVI DL 201 Rx.
CONTROL
PASS THRU
Tx Rx
DVI-D OUTPUT
DVI 201 Rx SERIES
9
10
11
DVI DL 201 Rx front panel features
Power LED — An amber light indicates that the DVI DL 201 Rx
is receiving power from a power supply or remotely, through
the transmitter. A green light indicates that the receiver is also
receiving a video signal.
i
DVI-D output — One female DVI-I connector provides a
dual-link DVI-D output.
j
k
Control signal pass-through — A three-pole, 3.5 mm captive
screw connector inputs pass-through RS-232 (two-way) or IR
signals (one-way).
DVI DL 201 Tx/Rx • Installation
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI DL 201 Rx rear panel features
The illustration below shows the rear panel features of the
DVI DL 201 Rx.
INPUTS
POWER
1
2
3
12V
0.4A MAX
DO NOT
CONNECT
INPUTS TO
LAN
12
13
DVI DL 201 Rx rear panel features
Power input — An optional 12 VDC power supply (not
provided) connects to this two-pole, 3.5 mm captive screw
connector.
l
m
The receiver can be remotely powered by the transmitter.
N
Twisted pair inputs — Three RJ-45 jacks receive video, remote
power, and pass-through communications/control signals from
the transmitter. They can also send pass-through control signals
via the transmitter.
The DVI DL 201 transmits high frequency signals via
these TP outputs. Connections between the transmitter
and receiver must be point to point. It is recommended
that there should be no couplers, adapter, or patch panels
between the transmitter and receiver units.
N
DVI DL 201 Tx/Rx • Installation
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Cable Connections and Switches
DVI-D input
Connect the DVI-D source device to the female DVI-I input
connector.
The dual link DVI-D input carries a signal with a resolution up
to 2560x1600 @ 60 Hz.
For sources providing HDMI signals, use an HDMI to DVI
adapter, such as the Extron HDMIF-DVIDM female HDMI to
male DVI-D adapter (PN 26-616-01). The pin assignments for
the DVI-I input connectors are shown in the table on the next
page.
DVI-D output
Connect the local display device to the female DVI-I output
connector on the rear panel of the transmitter and the remote
display device to the output connector on the front panel of the
receiver.
The dual link DVI-D output carries a signal with a resolution up
to 2560x1600 @ 60 Hz.
The pin assignments for the DVI-I output connectors are the
same as those for the input connectors and are shown in the
table on the next page.
Although DVI-I connectors are used, the DVI DL 201 is
compatible only with DVI-D signals.
N
DVI DL 201 Tx/Rx • Installation
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI Dual Link - Female
1
8
9
17
24
Pin
1
Signal
Pin
Signal
Pin
Signal
TMDS data 2–
TMDS data 2+
9
TMDS data 1–
17 TMDS data 0–
18 TMDS data 0+
2
10 TMDS data 1+
TMDS data
2/4 shield
TMDS data
11
TMDS data
19
3
1/3 shield
0/5 shield
4
5
12
20
TMDS data 4-
TMDS data 3-
TMDS data 5-
TMDS data 4+ 13
TMDS data 3+ 21 TMDS data 5+
TMDS clock
6
7
8
DDC clock
14
15
16
+5 V power
22
shield
DDC data
Ground
23 TMDS clock+
CEC control*
Hot plug detect
TMDS clock–
24
*CEC control on pin 8 is a proprietary usage and is not the
industry standard
DVI DL 201 Tx/Rx • Installation
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Twisted pair output/input
Terminating shielded cable
CAT 5/5e/6/7 twisted pair cable is not provided with the
transmitter/receiver pair. You may purchase cables that have
been precut to the required length and terminated to the T586A
or T586B standard (see the table on the next page).
Alternatively, purchase bulk cable and use the RJ-45 connectors
(provided) to prepare your own terminated cables as described
below.
The transmitter and receiver pair works with unshielded
twisted pair (UTP) or shielded twisted pair (STP) cables.
To ensure FCC Class A and CE compliance, and for
optimum performance, STP cables are recommended.
N
Do not use Extron Skew Free Cable with this product.
N
1.
2.
Cut the cables to the required length. All three cables
should be the same length.
Remove about 7/8" (2.2 cm) of the outer coat. If using STP
cable, peel back the shielding and fold it over the top of the
outer coat.
Peel back shield and
fold back.
3.
4.
Cut away and discard the clear cellophane inner wrapper
that extends beyond the folded back shielding.
Cut a piece of self-adhesive shielded aluminum tape
(provided), remove the backing, and wrap it around the
folded back shielding.
Wrap tape around folded foil shielding.
Aluminum Tape
Slightly overlap.
Cut and save the excess tape
for other connectors.
5.
Separate the individual wires, and arrange them so that all
eight wires are side by side in the same order as the T586A
or T586B standard shown at the top of the next page. Both
ends of a cable must be wired to the same standard (T586A
or T586B).
DVI DL 201 Tx/Rx • Installation
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
TIA/EIA
Pin # T 586 A
TIA/EIA
T 586 B
Cable 1 Cable 2
Cable 3
Wire color
Wire color
1
2
3
4
5
6
7
8
White-green
Green
White-orange Data 0+
CEC
HPD
Data 3+
Data 3+
Orange
Data 0+
IDCK+
Data 1+
Data 1+
IDCK-
White-orange White-green
RS-232 Tx/IR+ N/C
Blue
Blue
DDC Clock
+12 V
Data 4+
White-blue
Orange
White-blue
Green
Data 4+
N/C
RS-232 Rx
DDC Data
Ground
White-brown White-brown Data 2+
Brown Brown Data 2+
Data 5+
Data 5+
Side
Pins:
12345678
6.
Feed the wires into the RJ-45
connector (see the figure at right)
and crimp the cable in the normal
manner (see the figure below),
folding the tangs of the connector
over the shielded tape.
Insert
Twisted
Pair Wires
Crimped Connector
Connections
Use RJ-45 connectors to link the output from the transmitter
to the appropriate input on the receiver. Three CAT 5/5e/6/7
twisted pair (TP) cables connect the transmitter with the
receiver.
The transmitter and receiver pair works with unshielded
twisted pair (UTP) or shielded twisted pair (STP) cables.
To ensure FCC Class A and CE compliance, and for
optimum performance, STP cables are recommended.
N
Connect the output from the transmitter to the input of the
receiver that has the same number:
•
•
•
Transmitter port 1 connects to receiver port 1.
Transmitter port 2 connects to receiver port 2.
Transmitter port 3 connects to receiver port 3.
DVI DL 201 Tx/Rx • Installation
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Single Link/Dual Link DVI
Dual Link DVI carries signals at resolutions up to
2560x1600 @ 60 Hz. Single Link DVI carries signals at
resolutions up to 1920x1200 @ 60 Hz.
Single Link Mode Dual Link Mode
Video Resolution
(60 Hz)
UTP
STP
UTP
STP
1024x768
720p
200'
(60 m)
200'
(60 m)
200'
(60 m)
200'
(60 m)
1080i
1920x1200
1600x1200
1080p
100'
(30 m)
125'
(38 m)
200'
(60 m)
200'
(60 m)
2560x1600
N/A
N/A
100'
(30 m)
125'
(38 m)
The transmission distance varies greatly depending on
signal resolution and on the type of cable, graphic card,
and display used in the system.
N
•
•
•
To operate in Dual Link mode, all three TP cables are
required and both the source and display devices must
support Dual Link DVI signals.
To operate in Single Link mode, only TP cables 1 and 2 are
required. Dual Link DVI is backwards compatible with
Single Link DVI.
The DVI/HDMI 201 (Single Link) receivers can be used
with the DVI DL 201 transmitter, in Single Link mode
(using only TP cables 1 and 2).
DVI DL 201 Tx/Rx • Installation
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
DDC switches
When the DVI-D source device boots up, it uses the Display
Data Channel (DDC), a two-way communication protocol, to
obtain Extended Display Identification Data (EDID) from the
display device. This allows the source to output a resolution
that matches the capabilities of the display.
A bank of three switches allows the user to determine how the
source device will obtain the EDID. The EDID can be obtained
directly from the display device, or from the internal memory
within. The three switches are:
EDID Minder — This switch must be on for the EDID Minder
function to be enabled. The factory default for this switch is the
off position.
Default EDID — When the Default EDID switch
is on (factory default; see figure at right), an EDID
showing a typical Dual Link DVI display resolution
ON
of 2560x1600 @ 60 Hz is passed to the source device.
ON
The EDID Minder switch must also be on for the
Default EDID switch to function.
1
2
3
OFF
Remote DDC — When this switch is off, the DDC
is routed to the local monitor. When the switch is on, the DDC
is routed to the remote display device.
See page 3-2 for more information about configuring these
switches to provide the source device with the correct EDID.
DVI DL 201 Tx/Rx • Installation
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Control pass-through
Tx Rx
The DVI DL 201 Tx/Rx cannot be
controlled by RS-232 or IR controls.
However, they are able to pass signals
from a control device to a remote device
that is controlled by those signals.
The RS-232 and IR
N
communications are via a
passive pass-through only;
the transmitter and receiver
neither generate nor respond
to these signals.
3/16" (5 mm)
MAX
Use the three-pole, 3.5 mm captive
screw connector on the transmitter
to input RS-232 or IR signals from a
control device. Use the corresponding
connector on the receiver to pass signals
to the output display.
Tx Rx
3-Pole
Captive Screw
Connector
The ideal length of exposed wire in the stripping
process is 3/16" (5 mm). If longer than 3/16", the
exposed wires may touch, causing a short circuit.
If shorter than 3/16", the wires can be easily pulled
out even if tightly fastened.
C
Do not tin the wires. Tinned wire does not hold its
shape and comes loose over time.
DVI DL 201 Tx/Rx • Installation
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL
RS-232 signals
RS-232 signals are bidirectional —
PASS THRU
Tx Rx
DVI DL 201
Transmitter
or Receiver
signals pass from the control device and
replies return from the remote device.
To connect the control device to the
transmitter, or the receiver to the remote
device, make the following connections,
as shown at right:
RS-232 Control
or Display Device
• Tx to Tx
• Rx to Rx
Tx Rx
•
(ground) to
For information about controlling display devices with
RS-232 commands, please refer to the user's manual of
that device.
N
IR signals
IR signals are one-way (from control device
to the IR emitter that broadcasts the IR
signal remotely). There are no responses
and no requirement for a reverse pathway.
To connect the control device to the
transmitter or the receiver to the IR emitter,
make the following connections, as shown
at right:
CONTROL
PASS THRU
Tx Rx
DVI DL 201
Transmitter
or Receiver
• The Signal (S), from the control device to
Tx of the transmitter.
IR Control
or IR emitter
S
G
• The ground (G) of the control device is
connected to the ground ( ) of the transmitter.
• The Tx of the receiver to the S of the IR emitter.
• The ground ( ) of the receiver to the ground (G) of the IR
emitter.
DVI DL 201 Tx/Rx • Installation
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Power input
1.
Connect the captive screw connector from the supplied
12 VDC power supply into the power receptacle.
Twisted pair cable 2, pin 5 carries a 12 VDC power signal.
This remote powering feature allows a single power
supply, connected to the transmitter, to power both the
transmitter and receiver.
Power supply voltage polarity is critical. Incorrect
voltage polarity can damage the power supply, the
transmitter, and/or the receiver. Identify the ground
( ) lead by the ridges on the side of the cord (see the
figure below).
C
POWER
12V
0.4A MAX
Power Receptacle
Smooth
Ridges
A
A
DC Power Cord
Captive Screw Connector
Ground
+12 VDC
External
Power Supply
(12 VDC, 1 A )
AC Power Cord
Connecting power to DVI DL 201 Tx/Rx
The ideal length of exposed wire in the stripping
C
process is 3/16" (5 mm). If longer than 3/16", the
exposed wires may touch, causing a short circuit.
If shorter than 3/16", the wires can be easily pulled
out even if tightly fastened.
Do not tin the wires. Tinned wire does not hold its
shape and comes loose over time.
2.
3.
Connect the AC power cord of the power supply unit to a
110 or 220 VAC electrical source.
When the transmitter or receiver is getting power, either
directly from the power supply or indirectly through the
remote powering feature (receiver), the front panel LED
lights amber.
DVI DL 201 Tx/Rx • Installation
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI DL 201 Tx/Rx
Chapter Three
3
Configuration and Operation
Configuration
Setup and Operation
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration and Operation
Configuration
Using the EDID Minder to read and store EDID
from a display
During boot up, the DVI-D source device uses Display Data
Channel (DDC) to obtain Extended Display Identification Data
(EDID) from the display device. This allows the output signal to
match the resolution and refresh rate of the display device.
The DVI DL 201 Tx/Rx uses Extron's EDID Minder, which
allows the user to store and use EDID from any display device.
To use this feature, follow these steps:
1.
Disconnect all devices and cables from the transmitter and
receiver.
2.
Connect the desired display to the transmitter's Local
Monitor output. For best results, the cable for this
connection should be 15' (4.5 m) or shorter.
3.
4.
5.
6.
Apply power to the transmitter and the display device. If
necessary, connect the power supply to the transmitter.
Set the EDID Minder switch on the transmitter
to the on (up) position (see the figure at right).
Set the Default EDID switch to the off (down)
position (see the figure at right).
ON
ON
Set the Remote DDC to the off (down)
position to allow DDC routing to go to the
local monitor (see the figure at right).
1
2
3
OFF
The EDID Minder extracts information only from the
local monitor, not from the remote display.
N
EDID
7.
Press and release the EDID Minder Store
button. The LED next to the switch turns
from green to amber. This indicates that
the transmitter is reading and extracting
the EDID from the display connected to
the local monitor output.
STORE
When the information has been successfully extracted and
stored in non-volatile memory, the LED returns to green.
8.
9.
Turn off the display and disconnect it from the transmitter.
Connect the transmitter to the receiver with the three
twisted pair cables.
•
•
•
Transmitter port 1 connects to receiver port 1.
Transmitter port 2 connects to receiver port 2.
Transmitter port 3 connects to receiver port 3.
DVI DL 201 Tx/Rx • Configuration and Operation
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Power up the transmitter and the receiver. A single power
supply can provide power to both units through the
remote power connection.
11. Connect the remote display to the receiver output. A local
monitor display can also be connected to the transmitter
output at this time.
12. Connect the DVI source to the transmitter input.
13. Check that the transmitter switches are in the positions
described in steps 4-6.
14. Power on the DVI source device. The source device reads
and uses the EDID information stored in the transmitter
memory and boots up with that resolution.
15. Power on the remote (and local) display device(s).
All display devices must be capable of handling
resolutions equal to or greater than that of the device
used to set the EDID.
N
Using the EDID Minder with the default EDID
1.
Set the EDID Minder switch to the on (up)
position and the Default EDID switch to the
on (up) position (see the figure at right). The
position of the Remote DDC switch is not
relevant.
ON
ON
2.
3.
Connect the source device to the transmitter
input.
1
2
3
OFF
Connect the display device to the receiver
output and, if required, the local monitor to the transmitter
output.
4.
Connect the transmitter to the receiver with the three
twisted pair cables.
•
•
•
Transmitter port 1 connects to receiver port 1.
Transmitter port 2 connects to receiver port 2.
Transmitter port 3 connects to receiver port 3.
5.
6.
Power on all devices.
The source boots using EDID showing a native resolution
of 2560x1600, regardless of the display device.
All display devices must be capable of handling
resolutions equal to or greater than the default values.
N
DVI DL 201 Tx/Rx • Configuration and Operation
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration and Operation, cont’d
Using pass-through mode with DDC routed to a
local monitor
1.
Set the EDID Minder switch to the off (down)
position and the Default EDID switch to the
off (down) position (see the figure at right).
The position of the Remote DDC switch is not
relevant.
ON
ON
2.
3.
Connect the source device to the transmitter
input.
1
2
3
OFF
Connect the display device to the receiver
output and, if required, the local monitor to the transmitter
output.
4.
Connect the transmitter to the receiver with the three
twisted pair cables.
•
•
•
Transmitter port 1 connects to receiver port 1.
Transmitter port 2 connects to receiver port 2.
Transmitter port 3 connects to receiver port 3.
5.
6.
Power on the local monitor.
Boot up the source device. The source boots with the
resolution and refresh rate of the local monitor.
Because the local monitor is the source of EDID, it must
be powered on before the source device is booted.
N
7.
Power on the display device.
The remote display device must be capable of handling
a resolution equal to or greater than that of the local
monitor.
N
DVI DL 201 Tx/Rx • Configuration and Operation
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Using pass-through mode with DDC routed to the
remote display
This is the factory default setting.
N
Although DDC can be routed to the remote display, there
may be instances when the signals become corrupted or
weak. In those cases, the source device may be unable to
boot up correctly.
N
1.
Set the EDID Minder switch to the off (down)
position and the Remote DDC switch to the
on (up) position (see the figure at right). The
position of the Default EDID switch is not
relevant.
ON
ON
1
2
3
OFF
2.
3.
4.
Connect the source device to the transmitter
input.
Connect the display device to the receiver output and, if
required, the local monitor to the transmitter output.
Connect the transmitter to the receiver with the three
twisted pair cables.
•
•
•
Transmitter port 1 connects to receiver port 1.
Transmitter port 2 connects to receiver port 2.
Transmitter port 3 connects to receiver port 3.
5.
6.
Power on the remote display.
Boot up the source device. The source boots with the
resolution and refresh rate of the remote display.
Because the remote display is the source of EDID, it
must be powered on before the source device is booted.
N
7.
Power on the local monitor, if required.
If used, the local monitor must be capable of handling
a resolution equal to or greater than that of the remote
display.
N
DVI DL 201 Tx/Rx • Configuration and Operation
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration and Operation, cont’d
Setup
1.
Determine which source will be used for the EDID
information and configure the DDC switches appropriately
(see pages 3-2 to 3-5). If necessary, use the EDID Minder to
read and store information from a display (see pages 3-2 to
3-3).
2.
3.
4.
Prepare twisted pair cables (see "Terminating shielded
cable" on page 2-14).
Connect the transmitter to the receiver (see "Connections"
on page 2-15)
Connect the source device to the transmitter (see "DVI-D
input" on page 2-12). Do not power on the source device at
this time.
5.
Connect the display device to the receiver (see "DVI-D
output" on page 2-12). If required, connect a local monitor
to the transmitter.
6.
7.
If required, connect any RS-232 or IR control devices (see
"Control pass-through" on pages 2-18 to 2-19).
Connect the power supply to the transmitter (see "Power
input" on page 2-20).
8.
9.
Power on the display device.
Power on and boot up the source device.
Troubleshooting
If the DVI DL 201 Tx/Rx does not provide a high quality output
signal, check the following possibilities before contacting
your Extron representative (see the back cover for contact
information). Be sure to read all the suggestions as many of the
issues have several possible solutions.
No output signal — Check that the front panel LEDs for both
the transmitter and receiver are on (lit amber). If they are not,
check the power supply connections to the units.
If a single power supply is being used to power both units, it
must be connected to the transmitter.
Do not try to power both units with a single power
supply connected to the receiver as that will not provide
adequate power to the transmitter.
N
There are some circumstances, particularly with longer
Unsheilded Twisted Pair (UTP) cable runs, where the receiver
may not get adequate power. Under these circumstances, it may
be necessary to use two separate power supplies, one for the
transmitter and one for the receiver.
DVI DL 201 Tx/Rx • Configuration and Operation
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Insure all three twisted pair cables are firmly seated in the
correct receptacles.
No output signal or poor quality signal — Check the integrity
of the UTP or STP cables between the transmitter and the
receiver.
The transmitter and receiver pair works with unshielded
twisted pair (UTP) or shielded twisted pair (STP) cables.
To ensure FCC Class A and CE compliance, and for
optimum performance, STP cables are recommended.
N
•
•
•
Ensure that the twisted pair cables are terminated correctly
and to the same standard at both ends (see "Terminating
shielded cable" on page 2-14).
Ensure that each RJ-45 connector is firmly seated in its
receptacle and that each transmitter port is connected to
the correct receiver port (see pages 2-14 and 2-15).
Ensure that the length of the twisted pair cable does
not exceed the guidelines for single link or dual link
connections (see page 2-16).
Image loss or jitter — DVI signals run at very high frequency
and are especially susceptible to bad video connections, too
many adapters, or cables that are too long. To avoid loss of an
image or introduction of image jitter:
•
The DVI cable on the input to the transmitter or the output
from the receiver should not exceed 10' (3 m).
•
•
Use only cable designed for DVI signals.
Limit or avoid the use of adapters, patch panels, or
couplers with the input DVI cables, the output DVI cables,
and/or the twisted pair cables. Additional links in the
chain reduce signal integrity and overall cable length
performance.
•
Always turn on the display before the DVI video source in
order for the source to retrieve the DDC from the display.
No video signal or incorrect resolution or refresh rate — If the
source device is not able to obtain EDID information when it is
being powered on, it may not be able to send a video signal or
the signal may have the wrong resolution or refresh rate.
•
Ensure that the DDC DIP switches are set correctly for the
EDID source (see pages 3-2 to 3-5).
•
The source device must be powered on after the display
device providing the EDID source has been powered on.
Incorrect color or tint — Ensure that the twisted pair cables are
terminated correctly and to the same standard on both ends of
the cable (see page 2-14 and 2-15).
DVI DL 201 Tx/Rx • Configuration and Operation
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration and Operation, cont’d
Display device displays a flashing black or blue screen, snow,
or other distortion — A device that is not High-Bandwidth
Digital Content Protection (HDCP) compliant may be receiving
HDCP-encrypted signals.
The DVI DL 201 Tx/Rx is compatible with HDCP signals only
when the EDID Minder is disabled. HDCP signals can be
passed through to only one display (remote or local) and only
that display shows the signal correctly.
Signal on local monitor but not on remote display — Check
that both output devices (local and remote) can handle
resolutions equal to or greater than the EDID source.
DVI DL 201 Tx/Rx • Configuration and Operation
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI DL 201 Tx/Rx
Appendix A
A
Reference Information
Specifications
Included Parts
Optional Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Information
Specifications
Video
Maximum data rate....................... 10 Gbps (3.3 Gbps per color)
Maximum pixel clock ................... 330 MHz (165 MHz per link)
Resolution range ........................... Up to 2560x1600 @ 60 Hz
Formats........................................... RGB and YCbCr digital video
Standards........................................ DVI 1.0, HDMI 1.2
Video input and loop-through — transmitter
Number/signal type..................... 1 dual link DVI-D input
1 dual link DVI-D local loop-through
Dual link DVI is backwards compatible with all single link
DVI/HDMI signals.
N
Connectors ..................................... 2 DVI-I female (1 for input, 1 for
loop-through)
Interconnection between transmitter and receiver
Connectors ..................................... (3) RJ-45 per unit for 2 CAT 5/5e/7 or STP
(shielded twisted pair) cables connecting
the transmitter and receiver.
Termination standards.................. TIA/EIA T568A or T568B. Pin
configurations for each standard are
available in the "Installation" chapter.
Signal transmission distance
2560x1600 @ 60 Hz
CAT 5/5e/6/7 STP cable
Up to 125' (38 m)
CAT 5/5e/6 UTP (unshielded twisted pair) cable
Up to 100' (30 m)
Longer distances are possible with lower
rates
The transmission distance varies greatly depending on the signal
resolution and on the type of cable, graphics card, and display
used in the system.
N
DVI DL 201 Tx/Rx • Reference Information
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Video output — receiver
Number/signal type..................... 1 dual link DVI-D
Dual link DVI is backwards compatible with all single link
DVI/HDMI signals.
N
Connectors ..................................... 1 DVI-I female
Control/remote — external device (pass-through)
Serial control port input
Transmitter......................... RS-232 via (1) 3.5 mm, 3 pole captive screw
connector
Receiver .............................. 1 set of proprietary signals on a female
RJ-45 jack
Serial control port output
Transmitter......................... 1 set of proprietary signals on a female
RJ-45 jack
Receiver .............................. RS-232 via (1) 3.5 mm, 3 pole captive screw
connector
Protocol is mirrored between the transmitter and the receiver.
N
Serial control pin configuratins... Captive screw connectors: 1-TX, 2=RX,
3=GND
General
Recommended cable type............ CAT 5/5e/6/7 (shielded or unsheilded)
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, 6 W max.,
external; to 12 VDC, 2 A, regulated
Power input requirements........... 12 VDC, 0.4 A for both transmitter and
receiver
Each transmitter and receiver can be powered locally by an
external power supply. The receiver can be powered remotely by
a power supply connected to the transmitter on the other end of
the CAT 5/5e/6/7 UTP or STP cable.
N
Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C)/
10% to 90% noncondensing
Operating: +32 to +122 °F (0 to +50 °C)/
10% to 90% noncondensing
DVI DL 201 Tx/Rx • Reference Information
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Information
Cooling ........................................... Convection, no vents
Mounting
Rack mount........................ Yes, with optional 1U, 9.5" deep rack
shelf (RSU 129, #60-190-01 or RSB 129,
60-604-01); 1U, 6" deep rack shelf
(RSU 126, #60-190-10 or RSB 126,
60-604-10); or VersaTools® 1U, 3.5" deep
rack shelf (RSF 123, #60-190-20 or RSB 123,
#60-604-20)
Furniture mount................ Yes, with optional MBD 129 Through-Desk
Mounting Kit (#70-077-02)
Pole mount......................... Yes, with optional PMK 300 kit
(#70-374-01)
Enclosure type ............................... Metal
Enclosure dimensions
DVI DL 201 TX................... 1.75" H x 8.75" W x 3.0" D
(1U high, half rack wide)
(4.4 cm H x 22.2 cm W x 7.6 cm D)
(Depth excludes connectors)
DVI DL 201 RX .................. 1.0" H x 4.3" W x 3.0" D
(quarter rack wide)
(2.5 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors)
Product weight .............................. Transmitter: 0.6 lbs (0.3 kg)
Receiver: 0.3 lbs (0.1 kg)
Transmitter and receiver: 0.9 lbs (0.4 kg)
Shipping weight ............................ 2 lbs (1 kg)
Vibration......................................... ISTA 1A in carton (International Safe
Transit Association)
Regulatory compliance
Safety................................... CE, CUL, UL
EMI/EMC .......................... CE, C-tick, FCC Class A**, ICES, VCCI
MTBF............................................... 30,000 hours
Warranty ........................................ 3 years parts and labor
**FCC testing is conducted with STP (shielded twisted pair)
cable.
N
All nominal levels are at 10%.
N
N
Specifications are subject to change without notice.
DVI DL 201 Tx/Rx • Reference Information
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Included Parts
Included parts
Replacement
part number
(1 pair) DVI DL 201 Tx/Rx
or (1) DVI DL 201 Tx
60-957-01
60-957-12
60-957-13
or (1) DVI DL 201 Rx
(1) 12 VDC, 2A power supply
DVI DL 201 Tx/Rx User's Manual
Optional Accessories
Accessory
Part number
RSF 123 (3.5" deep, 1U VersaTools®
rack shelf kit)
60-190-20
RSB 123 (3.5" deep, 1U VersaTools
basic rack shelf)
60-604-20
RSU 126 (6" deep, 1U rack shelf kit)
RSB 126 (6" deep, 1U basic rack shelf)
RSU 129 (9.5" deep, 1U rack shelf kit)
RSB 129 (9.5" deep, 1U basic rack shelf)
PMK 300 Projector mounting kit
60-190-10
60-604-10
60-190-01
60-604-01
70-374-01
70-077-02
MBD 129 Through-desk mounting kit
(for DVI DL 201 Rx)
MBD 123 Through-desk mounting kit
(for DVI DL 201 Tx)
70-485-01
70-077-01
70-212-01
MBU 125 Under-desk mounting kit
(for DVI DL 201 Rx)
MBU 123 Under-desk mounting kit
(for DVI DL 201 Tx)
DVI DL 201 Tx/Rx • Reference Information
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Information
DVI DL 201 Tx/Rx • Reference Information
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
China:
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Middle East:
Extron Asia
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or non-
Extron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron USA - West Extron USA - East Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
Headquarters
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
Inside China Only
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
+86.21.3760.1568
+86.21.3760.1566 FAX
+1.714.491.1500
+1.714.491.1517 FAX
© 2008 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|