Eclipse Fujitsu Ten Car Stereo System CD5415 User Manual
OWNER'S MANUAL  
CUSTOMER NOTICE  
Please retain this booklet and write in the serial number  
of your CD5415 for identification.  
The serial number is labeled or stamped on the chassis.  
Serial No.  
CD5415  
ESN E5 High-Power CD Receiver with  
MP3 Decoder  
We appreciate your purchase of this receiver.  
Please read through this manual for correct operation.  
We suggest that after reading it you keep this manual  
in a safe place for future reference.  
FUJITSU TEN LIMITED  
Contact:FUJITSU TEN CORP. OF AMERICA  
19600 So. Vermont Avenue, Torrance, CA 90502  
Call:800-233-ECLIPSE  
"ECLIPSE" is a registered trademark of  
FUJITSU TEN LIMITED in 48 countries  
including the U.S. and Japan.  
www.eclipse-web.com  
(
)
090001-1465A700 0501MT F.O  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For your safety in using the  
CD5415  
Warnings and caution signs, illustrated below, are posted  
throughout this manual as well as on the CD5415. They show safe  
and correct ways to handle the product so as to prevent personal  
injury to you, others and to avoid property damage.  
Before reading through the manual, take time to read through and  
learn the important information listed in this section.  
This sign indicates a situation in which  
incorrect handling or disregard of this sign  
might result in death or serious personal injury.  
Warning  
This sign indicates a situation in which  
incorrect handling or disregard of this sign  
Caution  
might result in personal injury or may result  
solely in damage to property.  
Warning  
• Do not modify this system for use other than that specified  
herein. Also, do not deviate from the installation procedures  
described herein; Eclipse will not be held liable for damages  
including, but not limited to serious injury, death or property  
damage resulting from installations that enable unintended  
operation.  
• This equipment requires 12V DC and should only be installed in  
a vehicle with a 12V negative ground electrical system. Any  
other installation may cause a fire or other severe damage to  
the equipment and the vehicle.  
• Never install this equipment where it will interfere with safe  
operation of the vehicle. Never block the driver's view. Do not  
install equipment where it may interfere with operation of the  
brakes, the steering or any safety equipment, including seat  
belts and air bags.  
• Before drilling holes in a vehicle for installation, you must  
confirm the locations of pipes, tanks, electrical wiring, and  
other vehicle systems and components to ensure that there will  
be no interference or contact. In addition, you must also apply  
rust prevention and leak prevention measures at the drilling  
area. Otherwise, fire or electric shock could occur.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
Warning  
• When installing equipment do not remove or alter existing  
vehicle fasteners, including nuts, bolts, screws, clips, and  
fittings. Never detach, move or alter existing vehicle wiring,  
including electrical grounds and straps. Alteration of existing  
vehicle components may make vehicle unsafe to operate.  
• Before installation, remove the negative (-) battery terminal to  
prevent shocks, electrical arcing, fires, and damage to vehicle  
wiring and the equipment you are installing.  
• Secure wiring with tape or plastic ties so that wires do not  
interfere with vehicle operation, including brake pedal, gear  
shifter and steering. Position wires so that they will not be  
rubbed, abraded, or damaged by moving vehicle components,  
including power seats.  
• To avoid equipment and vehicle damage, including fire, never  
supply power to installed equipment in a way which will  
overload the capacity of an existing vehicle circuit. Never  
leave a power supply wire or connection uninsulated. Always  
install supplied fuses, circuit breakers, and relays.  
•
Air bags are vital safety equipment. Never install equipment in a way  
which will alter air bag wiring or interfere with air bag deployment.  
Air bags must function properly in the event of an accident.  
• When installation is complete, test all vehicle electrical systems  
for proper operation, including lights, horn, brake lights, and  
emergency flashers.  
• For your protection, never use a power drill without safety  
glasses or goggles. Debris or broken drill bits may cause  
severe eye injuries, including blindness.  
• Use electrical tape to insulate the ends of all wires, even if not  
used. Proper insulation prevents arcs, shocks and fires.  
• Some equipment uses batteries. Never install equipment  
where young children can get access to batteries. If a battery  
is swallowed, seek medical attention immediately.  
•
When vehicle is moving, never take your eyes off the road to make  
adjustments to the equipment. You must pay attention to the road  
to avoid accidents, do not let the operation or adjustment of the  
equipment distract you from proper vehicle operation.  
• The driver should not look at the screen while driving.  
Accidents may result if you are not paying attention to the  
forward direction.  
• Do not put foreign objects in the loading slot of disc. Fires or  
shocks may result.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Warning  
• Do not disassemble or alter this equipment. Accidents, fires or  
shocks may result.  
• Do not let water or foreign objects enter the internal parts of this  
equipment. Smoke, fires or shocks may result.  
• Pay attention to where the remote control is left. Traffic  
accidents or problems with driving may result if the remote  
control makes its way under the brake pedal etc. when the  
vehicle is stopped or when it goes around a corner.  
• Do not use when it is broken (the screen is not lit or no sound  
comes out). Accidents, fires or shocks may result.  
• Always replace fuses with fuses of identical capacity and  
characteristics. Never use a heavier fuse than the original.  
Using the wrong type of fuse may cause a fire or severe  
damage.  
• If foreign objects or water enters the equipment, smoke comes  
out, or there is a strange odor, stop using it immediately, and  
contact your dealer. Accidents, fires, or shocks may result if  
you continue to use it in these conditions.  
• The driver should not change the CD while driving. As  
accidents may result if you are not paying attention to the  
forward direction, first stop the car at a safe location and then  
proceed.  
• Plastic bags and wrappings may cause suffocation and death.  
Keep away from babies and children. Never put bag over your  
head or mouth.  
Caution  
•
•
Wiring and installing this equipment requires expertise and  
experience. Professional installation is recommended. Consult  
with your dealer or a professional installer. Incorrect wiring may  
damage the equipment or interfere with safe vehicle operation.  
Use only the accessory parts as specified. Using other parts may cause  
damage to the equipment or cause parts to fall or fly off the equipment.  
• Do not install the unit in places where it may get dew  
condensation on (around the air conditioning hose, etc.), come  
in contact with water, or in condition of high moisture, dust or  
oily smoke. If water, moisture, dust or oily smoke enters this  
unit, smoke, fires or malfunctions may result.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Caution  
• Avoid installing in places where it cannot be fastened securely  
or where there are strong vibrations. Also, if you installed the  
unit with double-sided tape, first wipe away dirt and wax from  
the installation area. Otherwise, the unit may come loose due  
to vibration while driving, causing problems for driving and  
resulting in traffic accidents or injuries.  
•
Do not install in places with direct sunlight or where it will be hit  
directly by hot air from the heater. This may increase the temperature  
of the interior of this equipment, resulting in fires and malfunctions.  
• Do not block the fan, heat sink or vents for this unit. When fan,  
heat sink or vent is blocked, the interior overheats, and fires  
may result.  
• Connect as specified in the installation manual. If not  
connected normally, fires or accidents may result.  
• When installing in vehicles equipped with air bags, check the  
manufacturer's cautions regarding operation before operating.  
Airbags may not operate properly.  
• Carry out the wiring such that cords are not pinched by  
movable parts such as seat rails, and screw parts of the vehicle  
body. Accidents, fires and shocks may result from  
disconnection and electrical shorts.  
• Carry out the wiring such that the cord does not make contact  
with metal parts. The cord is may be damaged by contact with  
metal parts, resulting in fire and shocks.  
• Avoid hot surfaces when wiring equipment. High temperatures  
may damage wiring, causing shorts, arcing and fires.  
• When changing the installation location for this equipment,  
please consult the dealer where you bought it for safety  
reasons. Expertise is necessary for removal and installation.  
• Keep volume to a reasonable level so that you can hear sounds  
from outside the vehicle, including warning sounds, voices, and  
sirens. Failure to do so may cause an accident.  
• Do not put your hands or fingers into the loading slot of disc.  
Injuries may result.  
• Do not touch the heat dissipating part of the amp. Burns may  
result from the heat of this part.  
• Do not recharge dry batteries. Dry batteries may rupture,  
resulting in injuries.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Caution  
• Do not use batteries other than those specified. Also, do not  
mix old and new batteries. Injuries or pollution to the  
surroundings may result from battery ruptures and leakage.  
• When inserting batteries into the equipment, be careful of the  
polarity (positive/negative), and insert them as indicated. If the  
battery polarities are incorrect, injuries and pollution to the  
surroundings may result from battery ruptures and leakage.  
• Replace used batteries as soon as possible; they may leak and  
damage equipment. Battery leakage can burn your skin or  
your eyes. Wash hands after handling.  
•
If alkaline solution from alkaline dry batteries makes contact with your  
skin or clothes, flush with clean water. If any of the solution gets in your  
eyes, also flush clean with water and then seek medical attention.  
•
When disposing of lithium dry batteries, affix insulating tape to  
the positive and negative terminals, and after they are insulated,  
dispose of them according to the "Local municipal directives".  
Shorts, fires and ruptures may result from disposal together with  
other electrically conductive objects such as metal parts, etc.  
•
Do not short, disassemble or heat the batteries, or place them in fire or  
water. Fire and injuries may result from battery rupture and leakage.  
• Store the remote control in a place away from direct sunlight,  
high temperatures, and high moisture levels. The case may  
change shape, and the batteries may rupture and leak.  
• Do not use this equipment except for in-vehicle use. Shocks or  
injuries may result.  
• Be careful of the position of the volume when turning the power  
source ON. Hearing damage may result if very loud noise is  
emitted when the power is turned ON.  
• Do not operate under abnormal conditions such as when the  
sound is broken or distorted. Fires may result.  
• This equipment uses invisible laser light. Do not disassemble  
or alter this equipment. If trouble occurs, contact the dealer  
where you bought the equipment. Altering this equipment may  
cause exposure to laser emissions (worsening eyesight), or  
result in accidents, fires or shocks.  
• If the equipment is dropped or the cabinet is broken, turn off  
the power to the main unit and contact your dealer. If used in  
this condition, fires or shocks may result.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Table of Contents  
Operating precautions ............................................ 11  
Notes on operation ..................................................................... 11  
About compact discs .................................................................. 12  
About cleaning a CD .................................................................. 14  
Names of controls and parts .................................. 15  
ESN security operating procedure ......................... 16  
About ESN .................................................................................. 16  
How to operate the ESN (Key CD) security ............................... 17  
How to program the Key CD ................................................ 17  
How to cancel the Key CD ................................................... 18  
How to change the Key CD .................................................. 19  
How to resume normal operation (ESN security lock out) ... 19  
What happens if an incorrect CD is inserted? ...................... 20  
How to turn the security indicator on/off ..................................... 21  
How to read the Electronic Serial Number ................................. 21  
Basic operation ........................................................ 22  
Turning the power on and off ..................................................... 22  
Listening to a CD ........................................................................ 23  
Listening to the tuner .................................................................. 24  
Adjusting audio volume .............................................................. 25  
Switching audio control modes ................................................... 26  
VOL (VOLUME) Mode ......................................................... 26  
BASS Mode ......................................................................... 26  
MID (MIDDLE) Mode ........................................................... 26  
TREB (TREBLE) Mode ........................................................ 27  
BAL (BALANCE) Mode ........................................................ 27  
FAD (FADER) Mode ............................................................ 27  
NON-F (NON-FADER) Mode ............................................... 27  
NF-P (NON-FADER PHASE) Mode ..................................... 28  
LOUD Mode ......................................................................... 28  
Storing user presets for the equalizer ........................................ 29  
Changing the equalizer mode .................................................... 30  
Making changes with Function Mode ......................................... 31  
Disabling the guide tone feature (for button operation) ........ 31  
Setting the time .................................................................... 32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
How to operate the CD player ................................. 33  
Listening to CDs ......................................................................... 33  
Advancing to the next track or returning to the beginning of the  
track being played ...................................................................... 34  
Fast Forward/Rewind ................................................................. 34  
Playing the beginning of tracks (SCAN) ..................................... 34  
Repeating the same track (REPEAT) ......................................... 35  
Playing tracks in random order (RANDOM) ............................... 35  
Ejecting the disc ......................................................................... 36  
Displaying CD TEXT .................................................................. 36  
How to operate the MP3 player ............................... 37  
About MP3 .................................................................................. 37  
What is MP3? ....................................................................... 37  
Playable MP3 file standards ................................................ 37  
ID3 tags ................................................................................ 37  
Media ................................................................................... 38  
Format of discs .................................................................... 38  
File names ........................................................................... 39  
Multi-sessions ...................................................................... 39  
Playing MP3 ......................................................................... 39  
MP3 playing time display ..................................................... 39  
Display order of MP3 file/folder names ................................ 39  
Listening to MP3 file ................................................................... 40  
Advancing to the next track (file) or returning to the beginning  
of the track (file) being played .................................................... 41  
Fast Forward/Rewind ................................................................. 41  
Skipping to the next or previous folder ....................................... 41  
Return to the root directory of the CD ........................................ 42  
Playing the beginning of files (SCAN) ......................................... 43  
Repeating the same file (REPEAT) ............................................ 43  
Playing files in random order (RANDOM) .................................. 44  
Displaying title ............................................................................ 45  
How to operate the tuner ........................................ 46  
Tuning to a station ...................................................................... 46  
Entering stations into memory automatically  
(The automatic preset mode: ASM) .......................................... 47  
Manually setting stations into memory ....................................... 48  
Preset station scan ..................................................................... 49  
Switching the display .................................................................. 49  
Changing the reception sensitivity for automatic scanning ........ 50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Changing the radio band location ............................................... 51  
FM reception characteristics ...................................................... 52  
FM reception differs from AM ............................................... 52  
Fading out ............................................................................ 52  
Reception area of FM broadcasts ........................................ 53  
Multipath .............................................................................. 53  
How to use an optional remote control ................. 54  
Precautions in use of the remote control .................................... 54  
Cleaning the remote control ....................................................... 54  
Turning the power on/off ............................................................ 55  
Adjusting the audio volume ........................................................ 55  
Muting the volume ................................................................ 55  
Switching playback modes ......................................................... 56  
How to play the tuner ................................................................. 56  
Selecting the FM/AM band ................................................... 56  
Selecting a station (manually or automatically) .................... 57  
Selecting preset stations ...................................................... 57  
How to play CDs ......................................................................... 57  
Switching disc mode ............................................................ 57  
Advancing to the next track or returning to the beginning  
of the track being played ...................................................... 58  
Skipping to the next or previous disc ................................... 58  
Listening to MP3 file.................................................................... 59  
Switching the disc mode ...................................................... 59  
Advancing to the next file or returning to the beginning  
of the file being played.......................................................... 60  
Skipping to the next or previous folder ................................. 60  
Fast Forward/Rewind ........................................................... 60  
Replacing the battery ................................................................. 61  
How to operate the receiver with an optional  
CD changer connected............................................. 62  
Listening to a CD......................................................................... 62  
Advancing to the next track or returning to the beginning of  
the track being played ................................................................. 62  
Fast Forward/Rewind .................................................................. 62  
Playing the beginning of tracks (SCAN)...................................... 63  
Repeating the same track (REPEAT).......................................... 63  
Playing tracks in random order (RANDOM) ................................ 64  
Skipping to the next or previous CD............................................ 64  
Specifying a CD to play............................................................... 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Switching the display .................................................................. 65  
How to operate the tuner with an optional  
HD RADIO tuner connected (U.S.A. only) .............. 66  
About HD Radio ......................................................................... 66  
Tuning to a station ...................................................................... 67  
Entering stations into memory automatically  
(The automatic preset mode: ASM) ........................................... 68  
Manually setting stations into memory ....................................... 69  
Preset station scan ..................................................................... 70  
Switching between displays when receiving HD Radio .............. 71  
HD Radio reception settings ....................................................... 72  
How to operate the tuner with an optional SIRIUS  
satellite radio tuner connected (U.S.A. only) ........ 73  
About SIRIUS satellite radio ....................................................... 73  
Selecting the radio mode ............................................................ 74  
Tuning to a channel .................................................................... 74  
Category selection ...................................................................... 75  
Direct channel selection ............................................................. 75  
Manually setting channels into memory ...................................... 76  
Preset channel scan ................................................................... 77  
Switching displays when using the SIRIUS satellite radio .......... 77  
If you have a question: ............................................ 78  
Displayed information (for troubleshooting) ................................ 79  
Specifications .......................................................... 82  
Before installation ................................................... 83  
Components ............................................................................... 83  
Installation angle ........................................................................ 83  
Mounting instruction ............................................... 84  
Mounting the main unit ............................................................... 84  
Names of lead wires and destinations ........................................ 87  
System ....................................................................................... 88  
How to contact customer service .......................... 93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Operating precautions  
Operating precautions  
<Your CD5415 will perform well over a long period of time through correct  
handling and care.>  
Notes on operation  
• For your safety, play only at volume levels that allow outside sounds to be  
heard.  
• We recommend using with this player a disc with  
the logo shown to the left.  
• You can play music CDs(CD-R/CD-RW) on this  
player. Be sure to use discs that have been  
properly processed.  
Depending on the editing equipment used, some  
discs may not play properly.  
• Do not insert anything other than a CD into the  
disc slot.  
Do not insert any foreign objects, such as coins or  
credit cards, into the disc slot. Be especially  
watchful of children’s mischief in this regard.  
• Avoid severe mechanical shock.  
When the player is subjected to severe vibration  
while traveling over a rough surface, playback  
may be intermittent. When a situation like this  
occurs, resume playback after returning to a  
smoother road.  
• About dew condensation.  
In cold or rainy weather, just as the interior glass  
surface gets fogged, dew (water condensation)  
may also settle on the deck. When this occurs,  
disc playback may become intermittent or  
impossible. Dehumidify the air in the vehicle for a  
while before resuming playback.  
• Cleaning the disc slot.  
The disc slot tends to get dusty. Clean it  
occasionally to prevent accumulated dust from  
scratching the discs.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Operating precautions  
About compact discs  
• The signal recorded on a compact disc is read by a laser beam, so  
nothing touches the disc surface. A scratch on the recorded surface or a  
badly warped disc may cause deteriorated sound quality or intermittent  
playback. Observe the following precautions to ensure high quality sound  
performance:  
• Do not leave an ejected disc in the disc slot  
for very long; the disc may warp. Discs  
should be stored in their cases and kept  
away from high temperature and humidity.  
• Do not stick a piece of paper or tape on, nor  
write on or scratch either side of a disc.  
• Discs spin at a high speed inside the deck.  
Keep cracked or warped discs out of the  
player to avoid damaging it.  
• Avoid touching the recorded surface when  
handling a disc; handle discs by their edges.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Operating precautions  
About brand new CDs  
About CD accessories  
• You may notice that some brand  
new discs are rough around the  
center hole or outside edge.  
Remove the rough edges with  
the side of a ballpoint pen, etc.  
Rough edges may prevent  
proper loading in the deck.  
Flakes from the rough edges  
may also stick to the recorded  
surface and interfere with  
playback.  
• Do not use accessories  
(stabilizers, protective seals, laser  
lens cleaners, etc.) sold for  
“improving sound performance”  
or “protecting CDs.” The changes  
in CD thickness or outside  
dimensions made by these  
accessories may cause problems  
in the player.  
Rough Edges  
Ballpoint  
pen  
• Please be sure NOT to attach any  
ring-shape protector (or other  
accessory) to your discs. Those  
protectors are commercially  
available and said to protect disc  
and to improve sound quality  
(and antivibration effect), but they  
can do more harm than good in  
regular uses. The most common  
problems are disc insertion, disc  
ejections, and won't play  
problems due to the protector  
ring that came off in the disc  
mechanism.  
Rough  
Edges  
Flakes  
Recorded surface  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Operating precautions  
About borrowed CDs  
About irregularly-shaped CDs  
• Specially-shaped CDs, like  
heart-shaped or octagonal CDs,  
cannot be played. Do not  
attempt to play them, even with  
an adapter, since they may  
damage the player.  
• Do not use a CD with glue or  
remnants of adhesive tape or  
labels. They may cause the CD  
to get stuck inside or damage  
the deck.  
How to remove CDs  
• When removing the ejected disc,  
pull it straight out along the slot.  
Pressing downward in the  
process may scratch the  
recorded surface of the disc.  
OKAY  
About cleaning a CD  
• Use a commercially available compact disc  
cleaner to clean a CD, wiping lightly from the  
center to the edge.  
• Do not use benzine, thinner, LP record spray  
or other cleaners on CDs. They may damage  
a CD’s finish.  
XXXX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Names of controls and parts  
Names of controls and parts  
①
② ③  
④
⑤ ⑥ ⑦ ⑧  
⑭
⑨
⑬
⑫
⑩⑧  
⑪
Ejects compact disc.  
[CD  
(EJECT) ] button  
Switches between disc modes.  
[DISC] button  
[FM AM] button  
Disc slot  
Switches to radio mode and switches radio bands.  
Inserts compact discs.  
Switches screen display and turns function mode ON/OFF.  
Sets the equalizer settings.  
[DISP FUNC] button  
[SOUND] button  
[SEL] button  
Selects radio stations and CD tracks.  
Automatically finds radio reception or to fast forward/rewind.  
Returns to previous screen.  
[
/
] button  
[RTN] button  
Resets deck functions to default settings.  
Selects radio preset channels and performs disc mode  
functions.  
[RESET] button  
Buttons [1] to [6]  
Adjusts volume and performs other functions.  
Turns deck power ON/OFF.  
[AUDIO CONTROL] button  
[PWR] button  
Mutes or cancels muting.  
[MUTE] button  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
ESN security operating procedure  
ESN security operating procedure  
About ESN  
This deck incorporates ESN (ECLIPSE Security Network). The ESN is  
a security system which disables all deck functions when the power  
is restored if the deck is stolen from the vehicle. Once the ESN is  
activated, removing power to the desk or vehicle will activate the  
security feature.  
Setting or canceling of the security feature can be done with a "Key  
CD". It is necessary to register a music CD as the "Key CD" in  
advance.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
ESN security operating procedure  
Button [6]  
[DISP FUNC] button  
How to operate the ESN (Key CD) security  
How to program the Key CD  
Check that the unit is in standby.  
1
Press and hold button [6], then the [DISP FUNC]  
button, and hold both for more than one second.  
2
A [SEC] message appears, then in two seconds it will  
change to [DISC].  
The CD5415 is now ready to accept your Key CD in the  
CD slot.  
•If a CD has already been inserted, a [SEC] message appears,  
and then the CD is ejected.  
ATTENTION  
•If a security is activated, programming the Key CD is not  
available.  
Insert the CD into the slot.  
3
A [SEC] message appears, then the Key CD is ejected.  
•If there is a problem with the inserted CD, an [ERR] message  
will appear for two seconds and the CD will be ejected. Reinsert  
ATTENTION  
the ejected CD.  
•If a CD causes the [ERR] message to appear twice in a row, a  
[CHANGE] message will appear for two seconds. Try another  
CD.  
•Copy protected CD and MP3 CD-ROM cannot be programmed  
for Key CD security.  
•The Security indicator will flash whenever the vehicle’s ignition  
is switched off.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
ESN security operating procedure  
Button [6]  
[DISP FUNC] button  
How to cancel the Key CD  
Check that the unit is in standby.  
1
2
Press and hold button [6], then the [DISP FUNC]  
button, and hold both for more than one second.  
A [SEC] message appears, then in two seconds it will  
change to [DISC].  
The CD5415 is now ready to accept your Key CD in the  
CD slot.  
If a CD has already been inserted, a [SEC] message appears,  
and then the CD is ejected.  
ATTENTION  
Insert your Key CD into the slot.  
3
A [CANCEL] message appears, then the Key CD is  
ejected.  
The Key CD is canceled.  
•This process cancels the protection for the ESN deck.  
•If power to the ESN deck is disconnected, then reconnected, a  
Key CD will not need to be inserted in order to return the unit to  
normal operation.  
ATTENTION  
•Inserting a CD other than the Key CD will not cancel the  
protection. Instead, the display [ERR] for two seconds, then the  
normal CD playback mode will activate.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
ESN security operating procedure  
How to change the Key CD  
First, cancel the existing Key CD.  
1
2
Refer to “How to cancel the Key CD.”  
Next, program a new Key CD.  
Refer to “How to program the Key CD.”  
How to resume normal operation (ESN security lock out)  
If power is disconnected while ESN security is active (a Key  
CD was programmed), operation is disabled until power is  
restored and the unit unlocked. Follow this procedure to  
resume normal operation.  
When the power is turned on after disconnecting  
1
the battery power, a [SEC] message will appear for  
two seconds. Thereafter, the message changes to  
[DISC] and the CD5415 is ready to accept your Key  
CD into the slot.  
Insert your Key CD into the slot.  
2
If the correct CD is inserted, an [OK] message will  
appear for two seconds and the CD will begin playing.  
•If an incorrect CD is inserted, an [ERR_] ("ERR" and error  
number) message will appear for two seconds, after which the  
ATTENTION  
CD will be ejected.  
•If [ERR5] (the 5th time an error has occurred) appears, [HELP]  
will appear, after which the CD will be ejected. When [HELP]  
appears, carry out the operations for an ESN security lock out  
by following the procedure in "What happens if an incorrect CD  
is inserted?" (See next page).  
•You must use the same CD used for Key CD programming; a  
duplicate CD may not work properly.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
ESN security operating procedure  
Button [6]  
[DISP FUNC] button  
What happens if an incorrect CD is inserted?  
After the 5th incorrect attempt, the display reads  
[HELP] for five seconds.  
1
[HELP] will appear for five seconds, after which the serial  
number will appear.  
Press button [6], then the [DISP FUNC] button, and  
hold them for five seconds.  
2
After the [SEC] message will appear for two seconds,  
rolling code will appear.  
3
Press the [DISP FUNC] button.  
A [DISC] message appears.  
You will have five more attempts the correct disc.  
4
Insert your Key CD into the slot.  
If the correct CD is inserted, an [OK] message will  
appear for two seconds and CD will be ejected.  
•If an incorrect CD is inserted, an [ERR_] ("ERR" and error  
number) message will appear for two seconds, after which the  
ATTENTION  
CD will be ejected.  
•This process cancels the protection for the ESN deck.  
ꢀ Note ꢀ  
If after five tries the correct Key CD is not inserted, the display  
reads [CALL800]; the unit must be returned to Eclipse to be  
reset. In this case, please contact your Eclipse dealer for  
assistance. For country-specific customer service information,  
refer to "How to contact customer service" on page 93.  
Your key CD can be easily forgotten. Write the  
album name in a reminder note (See Page 95).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
ESN security operating procedure  
Button [2]  
[DISP FUNC] button  
Button [4]  
How to turn the security indicator on/off  
Once ESN security is activated, the indicator flashes whenever the  
vehicle’s ignition is turned off, warning potential thieves that the unit  
is protected. However, if you do not want this visible deterrent, it may  
be turned off.  
With the unit in standby, press button [2], then the [DISP  
FUNC] button and hold both for more than one second.  
1
[IND. FLASH] or [IND. -----] appears on the display.  
2
[IND. FLASH] means the security indicator will flash when the  
vehicle’s ignition is off, and [IND. -----] means it will not. Repeat  
the above steps to reactivate the flash mode.  
How to read the Electronic Serial Number  
Check that the unit is in standby.  
1
Press button [4], then the [DISP FUNC] button, and hold  
both for more than one second.  
2
[ESN] appears on the display, followed by an eight-digit  
number; this number is your electronic serial number (ESN).  
You may use this number to identify your Eclipse CD5415 in  
the event it is recovered after being stolen.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
Basic operation  
Basic operation  
[PWR] button  
This section covers basic operating procedures. For additional  
details, please refer to the sections on specific functions.  
Turning the power on and off  
Turning the power on and off.  
When the power is turned on, the state used when the power was  
turned off such as CD and tuner playback is restored.  
When the vehicle has no ACC position on the ignition switch, care is  
needed when turning off the deck. Follow Step 2 or Step 3 when  
turning off the power.  
When power is OFF, press the [PWR] button.  
1
The power will come ON.  
When the deck's power is turned on for the first time or if the  
battery terminals have been disconnected because of a reason  
ATTENTION  
such as vehicle maintenance and the power is then turned back  
on, the deck will start up in FM1 mode. After this, the broadcast  
stations will be searched for automatically and stored in buttons  
[1] to [6].  
When power is ON, press the [PWR] button for less than  
two seconds.  
2
The power will go OFF and the deck will be in Standby.  
If you press the [PWR] button again for more than one second,  
the power will go completely off.  
When power is ON, press the [PWR] button for more  
than two seconds.  
3
The power will go completely OFF.  
If a car is not equipped with an ACC position (for example, a  
European car), keep the [PWR] button depressed for more than  
ATTENTION  
two seconds.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
Basic operation  
[DISC] button  
Listening to a CD  
Insert a CD into the disc slot, label side up.  
1
The CD will start playing.  
When a CD is already loaded, press the [DISC] button to switch  
to the CD mode.  
ATTENTION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
Basic operation  
[FM AM] button  
[
] button  
[SEL]  
button  
[
] button  
Buttons [1] to [6]  
Listening to the tuner  
Press the [FM AM] button.  
1
This will turn the tuner on.  
Press the [FM AM] button to switch to the desired FM or  
AM bands.  
2
3
4
Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in  
order each time the button is pressed.  
Turn the [SEL] button to the left or right to tune to a  
station.  
Turn to the right: Tunes to higher frequencies.  
Turn to the left: Tunes to lower frequencies.  
Press the [ ] or [ ] button to start the automatic station  
search.  
[
[
] button:  
] button:  
Starts searching toward higher frequencies.  
Starts searching toward lower frequencies  
•If stations have been stored in memory, pressing a button  
from [1] to [6] will directly select a station. (Refer to the section  
“Manually setting stations into memory” on page 48)  
ATTENTION  
•When an optional HD Radio tuner unit is connected, digital  
broadcasts have reception priority. (USA only)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
Basic operation  
[AUDIO CONTROL] button  
[MUTE] button  
Adjusting audio volume  
Turn the [AUDIO CONTROL] button to the left or right.  
1
Turn to the right: Increases the volume.  
Turn to the left: Decreases the volume.  
Press the [MUTE] button for less than one second to cut the  
volume or restore it instantly.  
ATTENTION  
Warning  
Do not adjust the volume or other controls while driving the  
vehicle. Do so only while parked in a safe location.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
Basic operation  
[AUDIO CONTROL] button  
Switching audio control modes  
Various audio control modes may be fine-tuned using this  
procedure.  
Press the [AUDIO CONTROL] button for less than one  
second to select the item to be adjusted.  
1
Modes will switch in the order shown below each time the  
button is pressed.  
VOL  
BASS  
NF-P  
MID  
NON-F  
TREB  
BAL  
FAD  
LOUD  
VOL (VOLUME) Mode  
Adjusts volume.  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Increases the volume.  
Turn to the left: Decreases the volume.  
BASS Mode  
Adjusts bass level. Bass mode can be adjusted for each  
source (CDP/CDC, FM and AM).  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Emphasizes low sounds.  
Turn to the left: Softens low sounds.  
MID (MIDDLE) Mode  
Adjusts middle level. Mid mode can be adjusted for each  
source (CDP/CDC, FM and AM).  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Emphasizes medium sounds.  
Turn to the left: Softens medium sounds.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
Basic operation  
[AUDIO CONTROL] button  
TREB (TREBLE) Mode  
Adjusts treble level. Treble mode can be adjusted for each  
source (CDP/CDC, FM and AM).  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Emphasizes high sounds.  
Turn to the left: Softens high sounds.  
BAL (BALANCE) Mode  
Adjusts left/right speaker balance.  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Emphasizes right speakers.  
Turn to the left: Emphasizes left speakers.  
FAD (FADER) Mode  
Adjusts front/rear speaker balance.  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Emphasizes front speakers.  
Turn to the left: Emphasizes rear speakers.  
NON-F (NON-FADER) Mode  
Adjusts non-fader level (for connected sub-woofers, etc.).  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Increases level.  
Turn to the left: Decreases level.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
Basic operation  
[AUDIO CONTROL] button  
NF-P (NON-FADER PHASE) Mode  
The merging of sound between the front and rear speakers and  
the woofer can be improved by selecting the phase.  
Switch the phase to a phase which lets the speakers combine  
without any disharmony.  
Turn the [AUDIO CONTROL] button to select NORMAL or  
REVERSE.  
NOR: Normal phase  
REV: Reverse phase  
LOUD Mode  
The loudness control may be turned on to emphasize low and  
high frequencies at low volume levels.  
Loudness compensates for the apparent weakness of low and  
high frequencies at low volume by boosting the bass and  
treble levels.  
Turn the [AUDIO CONTROL] button until the [LOUD ON]  
display appears on the screen.  
To disable the loudness feature, repeat the above procedure to  
display the [LOUD OFF] indication.  
ATTENTION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28  
Basic operation  
[AUDIO CONTROL] button  
Storing user presets for the equalizer  
The adjustment values for BASS, MIDDLE and TREBLE settings  
made in the audio control mode can be stored. The stored  
adjustment values can be called by changing the equalizer mode.  
For detail, see“Changing the equalizer mode”on page 30.  
Press the [AUDIO CONTROL] button for more than one  
second.  
1
The adjusted values are stored.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
Basic operation  
[SOUND] button  
Changing the equalizer mode  
EQ (equalizer) mode can be used to adjust the frequency of the  
audio channels being played back in accordance with the genre and  
instruments of the music being played.  
Apart from four equalizer modes, this deck offers the audio  
adjustment mode in which you can store set BASS, MIDDLE, and  
TREBLE adjustment values, and the CUSTOM Mode in which and  
you can apply these adjustment values.  
1
Press the [SOUND] button for less than one second.  
Each time the button is pressed, the equalizer mode changes  
in the following order.  
DEFEAT (equalizer OFF)  
POWER (bass tones emphasized)  
SHARP (high tones emphasized)  
VOCAL (mid tones emphasized)  
CUSTOM (stored user-preset values for the equalizer)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30  
Basic operation  
[DISP FUNC] button  
[SEL] button  
[RTN]  
button  
Making changes with Function Mode  
A variety of settings can be changed.  
Press the [DISP FUNC] button for more than one  
second.  
The function mode is activated.  
Turn the [SEL] button in either direction to display setting  
items for selection.  
1
2
Setting items will be displayed in the following order when the  
[SEL] button is turned to the right.  
BEEP  
CLOCK  
If the optional HD RADIO tuner is connected, the  
selections will switch in the following order.  
ATTENTION  
HD RADIO  
BEEP  
CLOCK  
Disabling the guide tone feature (for button operation)  
The receiver is set at the factory to emit a beep tone in  
response to button operation. The guide tone feature may be  
disabled in the following procedure:  
Turn the [SEL] button to select BEEP.  
1
Press the [SEL] button.  
2
The Guide Tone Mode will be switched ON/OFF.  
Turn the [SEL] button to select ON or OFF.  
3
Press the [SEL] button to select current setting.  
4
Press the [RTN] button.  
5
At this time, other adjustments can also be made in  
Function Mode.  
Press the [DISP FUNC] or [RTN] button to exit  
6
Function Mode.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
Basic operation  
[SEL] button  
[RTN]  
button  
[DISP FUNC] button  
Setting the time  
This receiver uses the 12-hour display notation.  
Turn the [SEL] button to select CLOCK.  
1
Press the [SEL] button.  
2
The clock adjustment mode is activated.  
Press the [SEL] button to display the item to be  
selected for adjustment.  
3
Hours or minutes will be switched each time the button is  
pressed.  
Turn the [SEL] button to the left or right.  
4
5
6
Turn to the right: Turns the time forward.  
Turn to the left: Turns the time back.  
Press the [RTN] button.  
At this time, other adjustments can also be made in  
Function Mode.  
Press the [DISP FUNC] or [RTN] button to exit  
Function Mode.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
32  
How to operate the CD player  
How to operate the CD player  
[DISC] button  
First press the [DISC] button to switch to the disc mode. It is  
assumed here that a CD has already been loaded into the unit.  
Listening to CDs  
Press the [DISC] button.  
1
This starts CD play.  
If an external CD changer is connected, each additional press  
of the [DISC] button will switch modes from CD changer 1 ➔  
CD changer 2 ➔ CD player.  
A changer or player with no discs loaded will be skipped.  
•Playback may be intermittent when there is a scratch on a CD  
or when the recorded side is dirty.  
Caution  
•Only two external CD changers may be connected.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
How to operate the CD player  
[
] button  
[SEL] button  
Button [4]  
[
] button  
Advancing to the next track or returning to  
the beginning of the track being played  
Turn the [SEL] button to the left or right.  
1
Turn to the right: Advances to the next track.  
Turn to the left: Returns to the beginning of the track being  
played. (Repeat turning for previous tracks.)  
Fast Forward/Rewind  
Fast forward or rewind the song currently being played.  
Press and hold the [ ] or [ ] button.  
1
[
[
] button: Fast forward.  
] button: Rewind.  
Playing the beginning of tracks (SCAN)  
Press button [4].  
1
Pressing the button causes the player to move up to the next  
track and play it for 10 seconds, then move up to the next track  
and play it for 10 seconds, and so on until the button is  
pressed again.  
•To continue playing a desired track, press the button again to  
stop scanning.  
ATTENTION  
•After the entire disc is scanned once, ordinary playback starts  
from the point where scanning started.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
34  
How to operate the CD player  
Buttons [5] and [6]  
Repeating the same track (REPEAT)  
Press button [5] to repeat the track being played.  
1
To cancel, press button [5] again.  
Playing tracks in random order (RANDOM)  
Press button [6] to play the tracks in random order.  
1
To cancel, press button [6] again.  
•During random playback, press button [5] to repeat the track  
being played. To cancel repeat play (go back to random play),  
ATTENTION  
press button [5] again.  
During playback of a particular track: The track being played is  
played repeatedly.  
While searching: The following track is played repeatedly.  
•Occasionally the same track happens to be played (selected)  
two or more times in a row; this is normal operation and is not a  
sign of a problem.  
•When any of the functions - “Playing the beginning of tracks,”  
“Repeating the same track” and “Playing tracks in random  
order” - is selected, a message such as [SCAN], [REPEAT] or  
[RANDOM] appears on the display to verify the current function.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
How to operate the CD player  
[CD  
(EJECT)] button  
[DISP FUNC] button  
Ejecting the disc  
Press the [CD  
(EJECT)] button.  
1
Disc is ejected.  
Displaying CD TEXT  
Only the built-in CD player supports CD TEXT. It can not be  
displayed with the optional CD changer. If the CD came with a logo  
shown below, it is recorded with a disc title and track titles. These  
information will be displayed during playback.  
Press the [DISP FUNC] button for less than one second.  
1
Each time the button is pressed, the following will be displayed  
in order.  
Elapsed time ➔ Disc title/Track title* ➔ Clock  
*: The display are shows a maximum of 8 characters and then scrolls to  
display the remaining characters.  
After the disc title is displayed, the track title will be displayed by  
scrolling. After the track title is scrolled the display will be fixed.  
If the CD does not contain any text data, "NO TITLE" will appear.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
36  
How to operate the MP3 player  
How to operate the MP3 player  
About MP3  
The making of MP3 files by recording from sources such as  
broadcasts, records, recordings, videos and live performances  
ATTENTION  
without permission from the copyright holder for uses other than  
personal enjoyment is prohibited.  
What is MP3?  
MP3 (MPEG Audio Layer III) is a standard format for audio compression  
technology. By using MP3, a file can be compressed to one-tenth the size  
of the original.  
This deck has limitations on MP3 file standards and recorded media and  
formats that can be used.  
Playable MP3 file standards  
• Supported standards: MPEG-1 Audio Layer III  
• Supported sampling frequencies: 44.1, 48 (kHz)  
• Supported bit rate: 64, 80, 96, 112, 128, 160, 192, 224, 256, 288, 320  
(kbps)  
* Supports VBR.  
* Does not support free format.  
• Supported channel modes: stereo  
ID3 tags  
MP3 files have an "ID3 Tag" that allows input of information so that data  
such as song title and artist can be saved.  
This deck supports ID3v.1.0, ID3v.1.1, ID3v.2.2 and ID3v.2.3 tags.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
How to operate the MP3 player  
Media  
Media capable of playing MP3 includes CD-R and CD-RW discs.  
Compared to CD-ROM media commonly used for music discs, CD-R discs  
are fragile in high temperature/high humidity environments and one section  
of the CD-R may become incapable of playback. Fingerprints or scratches  
on the disc may prevent playback or cause skipping during playback.  
Sections of a CD-R may deteriorate if left inside a vehicle for long periods of  
time. It is also recommended that CD-R discs be kept in a light-blocking  
case because the discs are vulnerable to ultra-violet light.  
Format of discs  
The format of discs to be used must be ISO9660 Level 1 or Level 2.  
Control items for this standard are as follows:  
• Maximum directory layers:  
8 layers  
• Maximum characters for folder names/file names: 128 (including "." and 3  
letter file extension)  
• Allowable characters for folder names/file names: A~Z, 0~9, _ (underscore)  
• Number of files/folders possible on a single disc: 512  
[Configuration example for CD supporting MP3]  
Root directory (F1)  
F2  
Folder 2  
001.mp3  
002.mp3  
003.mp3  
004.txt  
Number of files/folders possible on a single  
disc is 512.  
005.mp3  
Files aside from MP3 files (Example: 004.txt)  
also count as single files.  
Folder 158  
Folder 159  
F158  
F159  
001.mp3  
002.mp3  
Folder 255  
F255  
• Total number of folders possible on a single disc: 255  
• Maximum files/folders this deck can recognize:  
512*  
*: A root directory is counted as one folder.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
38  
How to operate the MP3 player  
File names  
Only files with the MP3 file extension ".mp3" can be recognized as MP3 and  
played. Be sure to save MP3 files with the ".mp3" file extension. The "MP"  
letters of the file extension will be recognized whether entered as  
uppercase letters or lowercase letters.  
If the ".mp3" file extension is attached to a file other than an MP3  
file, that file will be mistakenly recognized by the deck as an MP3  
Caution  
file and played, resulting in loud noise output that can damage  
the speakers. Be sure to avoid attaching the ".mp3" file extension  
to files that are not MP3 files.  
Multi-sessions  
Multi-sessions are supported, and playing of CD-R and CD-RW discs with  
annotated MP3 files is possible. However, when "Track at once" has been  
written, close the session or process the warning message. Standardize the  
format of each session without changing the format.  
Playing MP3  
When a disc with recorded MP3 files is inserted, the deck first checks all the  
files on the disc. No sound is output while the deck is checking the files on  
the disc. It is recommended that the disc be recorded without files other  
than MP3 files and without unnecessary folders in order to speed up the  
checking of disc files by the deck.  
MP3 playing time display  
It is possible that playing time will not be correct, depending on the writing  
condition of the MP3 file.  
* It is possible that playing time will not be correct when VBR Fast Up/Down  
is operated.  
Display order of MP3 file/folder names  
Names of MP3 folders and files within the same level are displayed in the  
following order.  
1. MP3 folders displayed first, by ascending order of numbers, letters.  
2. Files displayed next, by ascending order of numbers, letters.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
How to operate the MP3 player  
[DISC] button  
Button [3]  
Listening to MP3 file  
Press the [DISC] button.  
1
This starts MP3 file play.  
If an external CD changer is connected, each additional press  
of the [DISC] button will switch modes from CD changer 1 ➔  
CD changer 2 ➔ CD player.  
A changer or player with no discs loaded will be skipped.  
•Playback may be intermittent when there is a scratch on a CD  
or when the recorded side is dirty.  
Caution  
•Only two external CD changers may be connected.  
ꢀ Note ꢀ  
•When music data recorded in the normal way (CD-DA) is  
present on the same disc with MP3 music files, the normally  
recorded music data will be played. To listen to the MP3  
music files, press button [3] for more than one second.  
•When a non-MP3 file is played, [STBY ERR] will appear.  
•The optional CD changer cannot be used to play MP3 files.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
40  
How to operate the MP3 player  
[
] button  
[SEL] button  
[
] button  
Buttons [1] and [2]  
Advancing to the next track (file) or returning to  
the beginning of the track (file) being played  
Turn the [SEL] button to the left or right.  
1
Turn to the right: Advances to the next track (file).  
Turn to the left: Returns to the beginning of the track (file)  
being played.  
Repeat turning for previous tracks (files).  
Fast Forward /Rewind  
Fast forward or rewind the song currently being played.  
Press and hold the [ ] or [ ] button.  
1
[
[
] button: Fast forward.  
] button: Rewind.  
Skipping to the next or previous folder  
Press button [1] or [2].  
1
Button [1]: Selects the next lower folder.  
Button [2]: Selects the next folder.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
41  
How to operate the MP3 player  
[RTN]  
button  
Return to the root directory of the CD  
In the root directory, when a file cannot replay, the system will  
return to the first file that can perform a replay. (In the  
configuration example, the file is returning to 001.mp3. See  
page 38.)  
Press the [RTN] button.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
42  
How to operate the MP3 player  
Buttons [4] and [5]  
Playing the beginning of files (SCAN)  
Press button [4].  
1
Press the button briefly to play just the first 10 seconds of each  
song for all the files in the current folder being played.  
Pressing the button until [ALL SCAN] is displayed will play just  
the first 10 seconds of the first song in each folder.  
•To continue playing a desired track, press the button again to  
ATTENTION  
stop scanning.  
•After the entire disc is scanned once, ordinary playback starts  
from the point where scanning started.  
Repeating the same file (REPEAT)  
Press button [5].  
1
Press the button briefly to repeat the file being played.  
Pressing the button until [ALL REPEAT] is displayed will repeat  
all the files in the current folder being played.  
To cancel, press button [5] again.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
How to operate the MP3 player  
Buttons [5] and [6]  
Playing files in random order (RANDOM)  
Press button [6].  
1
Press the button briefly to randomly play the files in the current  
folder being played.  
Pressing the button until [ALL RANDOM] is displayed will  
randomly play the files in all the folders.  
To cancel, press button [6] again.  
•During random playback, press button [5] to repeat the file  
being played. To cancel repeat play (go back to random play),  
ATTENTION  
press button [5] again.  
During playback of a particular file: The file being played is  
played repeatedly.  
While searching: The following file is played repeatedly.  
•Occasionally the same file happens to be played (selected) two  
or more times in a row; this is normal operation and is not a sign  
of a problem.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
44  
How to operate the MP3 player  
[DISP FUNC] button  
Displaying title  
Press the [DISP FUNC] button for less than one second.  
1
Each time the button is pressed the following will be displayed  
in order.  
Folder Name/File Name*1 ➔ Tag*2 ➔ Folder Number/File  
Number ➔ Clock ➔ Elapsed Time  
*1: The display area shows a maximum of 8 characters and  
then scrolls to display the remaining characters.  
After the folder name is displayed, the file name will be  
displayed by scrolling. After the file name is scrolled, the  
display will be fixed.  
*2: If there is no tag data, "NO TAG" will appear.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
45  
How to operate the tuner  
How to operate the tuner  
[FM AM] button  
[SEL] button  
[
] button  
[
] button  
First, press the [FM AM] button to start tuner operation.  
There are automatic and manual methods for setting stations in  
memory. The receiver will accept up to 24 stations in memory: 6 in  
AM and 18 in FM (6 each for FM1, FM2 and FM3.) (Initial setting)  
Tuning to a station  
Press the [FM AM] button for less than one second to  
switch to the desired FM or AM bands.  
1
Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in  
order each time the button is pressed.  
Turn the [SEL] button to the left or right to tune to a  
station.  
2
Turn to the right: Tunes to higher frequencies.  
Turn to the left: Tunes to lower frequencies.  
Press the [ ] or [ ] button to start the automatic station  
search.  
3
[
[
] button: Starts searching toward higher frequencies.  
] button: Starts searching toward lower frequencies.  
•At times, it may be difficult to maintain optimum reception  
because the antenna affixed to your vehicle is in motion  
constantly (relative to the broadcast antenna), encountering  
continuous variation in the received radio signals’ strength.  
Other factors affecting reception include interference from  
natural obstacles, sign posts, etc.  
ATTENTION  
•When an optional HD Radio tuner unit is connected, digital  
broadcasts have reception priority. (USA only)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
46  
How to operate the tuner  
[FM AM] button  
[SEL]  
button  
Buttons [1] to [6]  
Entering stations into memory automatically  
(The automatic preset mode: ASM)  
Press the [FM AM] button for less than one second to  
switch to the desired FM or AM bands.  
1
Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in  
order each time the button is pressed.  
Press the [SEL] button for more than two seconds until a  
beep is heard.  
2
The automatic preset mode starts.  
The [ASM ON] indicator on the screen flashes, and stations are  
automatically entered in memory under buttons [1] to [6].  
These buttons are called preset buttons.  
•Pressing the preset buttons ([1] to [6]) allows you to make one-  
touch station selections. The frequency of the selected station  
ATTENTION  
is indicated on the display.  
•When a new station is set in memory, the station previously set  
in memory will be deleted.  
•If there are fewer than six receivable stations, the stations set in  
the remaining buttons will be retained.  
If the vehicle’s battery is disconnected (for repairs to the vehicle  
or for removing the receiver), all stations in memory will be lost.  
Caution  
In such a case, set stations in memory again.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
47  
How to operate the tuner  
[FM AM] button  
[SEL]  
button  
Buttons [1] to [6]  
Manually setting stations into memory  
This section covers the setting of stations in memory under the  
numbered buttons.  
Press the [FM AM] button for less than one second to  
switch between FM and AM.  
1
Turn the [SEL] button to the right or left to tune to the  
station to be entered in memory.  
2
Select any button, from [1] to [6], and press it for more  
than two seconds.  
3
The tuned station is now memorized and set in the button  
selected. Repeat the procedure to set additional manually  
tuned stations in memory, in turn, for buttons [1] to [6]. These  
buttons are called the preset buttons.  
•Pressing the preset buttons ([1] to [6]) allows you to make one-  
touch station selections. The frequency of the selected station  
ATTENTION  
is indicated on the display.  
•When a new station is set in memory, the station previously set  
in memory will be deleted.  
If the vehicle’s battery is disconnected (for repairs to the vehicle  
or for removing the receiver), all stations in memory will be lost.  
Caution  
In such a case, set stations in memory again.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
48  
How to operate the tuner  
[SEL]  
button  
Buttons [1] to [6]  
[DISP FUNC] button  
Preset station scan  
This function enables reception of all the stations in the preset  
buttons for five seconds each.  
Press the [SEL] button for less than one second.  
1
[P SCAN] will appear on the display, and stations stored under  
preset buttons [1] through [6] will be played for five seconds  
each.  
To stop the preset scan mode at a desired station, press  
the [SEL] button again.  
2
The receiver will stay tuned to the desired station.  
Switching the display  
Press the [DISP FUNC] button for less than one second.  
1
Each press of the button swicthes the display the clock and  
current frequency.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
49  
How to operate the tuner  
[FM AM] button  
Button [1]  
Changing the reception sensitivity for automatic scanning  
The deck lets you select the reception sensitivity to be used for  
automatic scanning of stations. The two sensitivity modes available  
for this deck are AUTO mode and DX mode.  
When an optional HD Radio tuner unit is connected, reception  
sensitivity is set to the AUTO Mode. The DX Mode is unavailable.  
ATTENTION  
(U.S.A. only)  
During automatic scanning, the reception sensitivity  
switches automatically to one of two levels. Initially the  
reception sensitivity is set to the low level so that only  
stations with strong signals are received. If no stations  
could be received, the reception sensitivity is increased  
so that stations with weaker signals can also be  
received.  
AUTO Mode  
DX Mode  
Because the reception sensitivity for automatic scanning  
is set to the high level from the start, even stations with  
weaker signals can be received. (Signal crossover may  
result in some stations being hard to hear.)  
Check that the deck is in standby mode.  
1
2
Press and hold the [FM AM] button, then button [1], and  
hold both for more than three seconds.  
The mode switches between AUTO mode and DX mode each  
time the buttons are pressed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
50  
How to operate the tuner  
[FM AM] button  
Button [3]  
Changing the radio band location  
The location for the radio bands used between the North America  
region and the Asia/Australia/Latin region can be switched. The  
default setting is USA (North America).  
When an optional HD Radio tuner unit is connected, radio band  
ATTENTION  
location is set to USA. Other radio band locations are  
unavailable.(U.S.A. only)  
Check that the deck is in standby mode.  
1
Press and hold the [FM AM] button, then button [3], and  
2
hold both for more than three seconds.  
The radio band switches in the order shown below each time  
the buttons are pressed.  
USA  
ASIA  
AUS  
LATIN  
After this, the broadcast stations will be searched for  
automatically and stored in buttons [1] to [6].  
Download from Www.Somanuals.com. All Manuals Search And Download.  
51  
How to operate the tuner  
FM reception characteristics  
In general, FM has much better tonal quality than AM. However, FM  
and FM stereo reception encounter several characteristic problems  
not encountered with AM. FM is more difficult to receive than AM in a  
moving vehicle. The following are explanatory notes on what to  
expect from FM reception and on how to get satisfactory  
performance.  
FM reception differs from AM  
A characteristic of transmitted signals is that lower frequencies  
travel further. FM frequencies are much higher than AM’s  
(similar to a ray of light): they won’t bend but they will reflect.  
Often, they will be interrupted by tall buildings, mountains, etc.,  
taking direct and indirect paths to your vehicle’s antenna. The  
distance at which FM stations can be received satisfactorily is  
usually not nearly as far as that which AM stations can be  
received.  
AM Radio Waves  
Ionosphere  
FM Radio Waves  
Ionosphere  
Fading out  
In weak signal or “fringe” reception areas, FM stations may  
fade out completely, or fade in and out. When driving in weak  
signal areas, such as near hills, through valleys or tunnels,  
among tall buildings, etc., you may encounter unusual noise  
interference. THIS IS NOT A TUNER PROBLEM. In this case,  
you can only wait until you are in a better reception area, tune  
to a stronger station, or reduce the treble level.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
52  
How to operate the tuner  
Reception area of FM broadcasts  
A home receiver can catch weak FM stereo signals through the  
use of a tall, directional or ultra-sensitive antenna. In a moving  
vehicle, the area for good reception is limited because of  
varying conditions encountered while driving, including the  
types and heights of broadcast antenna structures, signal  
strength, engine noise, etc. For best reception with manual  
antenna, extend the antenna mast as far as possible.  
Transmitting Antenna 100 Meters High  
Effective Radiation Power 1kW  
FM Stereo Auto Radio 12.4 miles  
FM Monaural Auto Radio 31 miles  
Home FM Stereo Receiver 62 miles  
Reception quality varies depending on the power of the FM  
station, natural and artificial barriers,weather conditions, etc.  
Multipath  
The reflection characteristics of FM waves cause another  
problem called multipath–FM wave signals reflecting off of  
buildings, mountains, etc. When the antenna receives direct  
and reflected waves at the same time, distortion of sound in the  
treble range often occurs, such as static or harsh-sounding  
voices. THIS IS NOT A TUNER PROBLEM. Only moving to  
another area with a clearer signal path can remedy the  
situation.  
DIRECT  
WAVE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
53  
How to use an optional remote control  
How to use an optional remote control  
Precautions in use of the remote control  
• Be careful when handling the remote control, especially  
because it is small and light. Dropping or striking it hard may  
damage it, wear out the battery or cause a malfunction.  
• Keep the remote control free of moisture, dust and water. Do  
not subject it to shock.  
• Do not place the remote control unit where it will get hot, such  
as on the dashboard or near a heater vent. Allowing the  
remote control unit to overheat may warp its case or cause  
other problems.  
• Do not operate the remote control unit while driving because  
doing so could cause an accident.  
• When using the remote control, point it directly at the remote  
control light receptor.  
• The light receptor may not operate correctly if it is exposed to  
bright light such as direct sunlight.  
• Be sure to press the [PWR] button on the main unit for more  
than two seconds to shut it down before leaving the car, or the  
car battery may be run down. When the main unit is shut down,  
the remote control will not work.  
• Remove the batteries from the remote control unit whenever it  
is not to be used for a long time.  
Cleaning the remote control  
• Use a dry cloth to keep the unit clean. If the remote control unit  
gets extremely dirty, clean it with a cloth moistened in diluted  
liquid detergent. Do not use alcohol or thinner; these  
compounds may damage the finish.  
• In no event should benzine or thinner be used. These  
substances will damage the case or finish.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
54  
How to use an optional remote control  
Remote-control  
light receptor  
[PWR]  
button  
[
] button  
[MUTE]  
button  
[
] button  
Turning the power on/off  
When the power is turned on, the state used when the power was  
turned off such as CD and tuner playing is restored.  
Press the [PWR] button.  
1
The power turns on or off each time the button is pressed.  
When the main unit is shut down, the remote control will not work.  
ATTENTION  
Adjusting the audio volume  
Press the [ ] or [ ] button.  
1
[
[
] button: Increases the volume.  
] button: Decreases the volume.  
Muting the volume  
Press the [MUTE] button to cut the volume or restore it  
instantly.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
55  
How to use an optional remote control  
[MODE] button  
[TU] button  
[BAND] button  
Switching playback modes  
Press the [MODE] button.  
1
Press the button to switch modes in the following sequence:  
Tuner  
Disc  
How to play the tuner  
Select the tuner mode first.  
Selecting the FM/AM band  
Press the [BAND] or [TU] button.  
1
Each press will switch tuner modes from FM1 ➔ FM2 ➔  
FM3 ➔ AM.  
•It is not possible to switch between FM/AM modes and SIRIUS  
ATTENTION  
with the remote control.  
•If the optional SIRIUS tuner is connected, the selections will  
switch the modes from SR1  
➔
SR2  
➔
SR3  
➔
SR4 in order.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
56  
How to use an optional remote control  
[DISC] button  
[BAND] button  
[
PRESET CH ] buttons  
[
TUNE SEEK ] buttons  
・
Selecting a station (manually or automatically)  
A short tap of the button will allow manual station tuning.  
Pressing for more than one second will start automatic tuning.  
Press the [ TUNE•SEEK ] button.  
1
[
[
] button: Tunes to higher frequency stations.  
] button: Tunes to lower frequency stations.  
Selecting preset stations  
A total of six stations may be selected (preset tuning) out of  
those already set in memory through the main unit. (Refer to  
“Manually setting stations into memory,” page 48.)  
Press the [ PRESET CH ] button.  
1
[
[
] button: Select the next higher number preset button.  
] button: Select the next lower number preset button.  
How to play CDs  
Select the disc mode first.  
Switching disc mode  
Press the [BAND] or [DISC] button.  
1
When one or two CD changers are connected, press the  
[BAND] or [DISC] button to change modes from CD  
player ➔ CD changer 1 ➔ CD changer 2.  
The indicator will skip a changer or player that has no  
discs loaded.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
57  
How to use an optional remote control  
[
DISC ] buttons  
[
TRACK ] buttons  
Advancing to the next track or returning to  
the beginning of the track being played  
Press the [  
TRACK  
] button.  
1
[
[
] button: Skips to the next track.  
] button: Returns to the beginning of the track being  
played. (Press repeatedly to move to  
previous tracks.)  
Hold the [  
] button down to fast forward, or the [  
] button  
to rewind through the track being played.  
ATTENTION  
Skipping to the next or previous disc  
Press the [ DISC ] button.  
1
[
[
] button: Selects the next higher number disc.  
] button: Selects the next lower number disc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
58  
How to use an optional remote control  
[DISC] button  
Listening to MP3 file  
Switching the disc mode  
Press the [DISC] button.  
1
The disc mode changes and the disc starts playing.  
Each press will switch the modes from CD player ➔ CD  
changer 1 ➔ CD changer 2.  
Any device that has no CD loaded or that is not  
connected is skipped.  
•The optional CD changer cannot be used to play MP3 files.  
•If normally recorded music data (CDDA) and MP3 music files  
are mixed, then normally recorded music data will be played.  
ATTENTION  
Caution  
Playback may be intermittent when there is a scratch on a CD or  
when the recorded side is dirty.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
59  
How to use an optional remote control  
[
DISC ] buttons  
[
TUNE•SEEK ] buttons  
Advancing to the next file or returning to  
the beginning of the file being played  
Advancing to the next file or returning to the beginning of the  
file being played.  
Press the [ TUNE•SEEK ] button.  
1
[
[
] button: Advances to the next track (file).  
] button: Returns to the beginning of the track (file)  
being played.  
Repeat pressing for previous tracks (files).  
Skipping to the next or previous folder  
Skipping to the next folder or returning the previous folder.  
Press the [ DISC ] button.  
1
[
[
] button: Selects the next folder.  
] button: Selects the next lower folder.  
Fast Forward /Rewind  
Press and hold the [ TUNE•SEEK ] button.  
1
[
[
] button: Fast forward.  
] button: Rewind.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
60  
How to use an optional remote control  
Replacing the battery  
To prevent accidents, store batteries out of the reach of  
children. If a child has swallowed one, consult a doctor  
immediately.  
Warning  
Use two AAA-size batteries.  
Remove the back cover of the remote control unit by  
gently pressing and sliding it in the direction indicated by  
the arrow.  
1
Install the two batteries provided into the compartment  
as illustrated inside the compartment.  
2
Return the back cover into place by sliding it in the  
direction indicated by the arrow.  
3
•Be extremely careful not to swallow the battery.  
•The battery life is approximately one year. If the remote  
Caution  
control unit does not operate correctly or if the button lamp  
gets dim, replace the batteries.  
•Be sure to orient the batteries correctly so that the positive  
and negative poles match the diagram.  
•Do not use one new battery and one old one; use two new  
batteries.  
•Use only two of the same kind of battery.  
•If any liquid is seen leaking from the batteries, remove both  
batteries and dispose of them properly. Thoroughly clean the  
battery compartment with a dry cloth. Then install new  
batteries.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61  
How to operate the receiver with an optional CD changer connected  
How to operate the receiver with an  
optional CD changer connected  
[SEL] button  
[DISC] button  
[
] button  
[
] button  
This section covers the operation of an optional CD changer that is  
connected to the receiver.  
To switch from another mode, press the [DISC] button.  
Listening to a CD  
Press the [DISC] button.  
1
Each press of the button switches the mode from CD Player ➔  
CD Changer 1 ➔ CD Changer 2.  
Advancing to the next track or returning to  
the beginning of the track being played  
Turn the [SEL] button to the left or right.  
1
Turn to the right: Advances to the next track.  
Turn to the left: Returns to the beginning of the track being  
played. (Repeat turning for previous tracks.)  
Fast Forward/Rewind  
Fast forward or rewind the song currently being played.  
Press and hold the [ ] or [ ] button.  
1
[
[
] button: Fast forward.  
] button: Rewind.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
62  
How to operate the receiver with an optional CD changer connected  
Buttons [4] and [5]  
Playing the beginning of tracks (SCAN)  
Press button [4].  
1
Pressing the button causes the changer to move up to the next  
track and play it for 10 seconds, then move up to the next  
track and play it for 10 seconds, and so on, on one CD, until  
the button is tapped again.  
Hold the button until the [ALL SCAN] display appears to play  
the first 10 seconds of the first track of every CD loaded.  
•To continue playing a desired track, press the button again to  
stop scanning.  
ATTENTION  
•After the entire disc is scanned once, ordinary playback starts  
from the point where scanning started.  
Repeating the same track (REPEAT)  
Press button [5].  
1
Pressing on the button causes the changer to repeat the track  
currently being played, until the button is tapped again.  
Hold the button until the [ALL RPT] display appears to repeat  
all tracks on the CD being played.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
63  
How to operate the receiver with an optional CD changer connected  
Buttons [1] and [2]  
Buttons [5] and [6]  
Playing tracks in random order (RANDOM)  
Press button [6].  
1
Pressing on the button causes the changer to play the tracks  
on the currently playing CD in random order, until the button is  
pressed again.  
Hold the button until the [ALL RAND] display appears to play  
tracks from all of CDs loaded in the currently selected  
changer, in random order.  
•During random playback, press button [5] to repeat the track  
being played. To cancel repeat play (go back to random play),  
ATTENTION  
press button [5] again.  
During playback of a particular track: The track being played is  
played repeatedly.  
While searching: The following track is played repeatedly.  
•Occasionally the same track happens to be played (selected)  
two or more times in a row, but it is not a sign of a problem.  
•When any of the functions - “Playing the beginning of tracks,”  
“Repeating the same track” and “Playing tracks in random  
order” - is selected, a message such as [SCAN], [ALL SCAN],  
[REPEAT], [ALL RPT], [RANDOM] or [ALL RAND] appears on  
the display to verify the current function.  
•Random play is not canceled even if a magazine is ejected.  
Skipping to the next or previous CD  
Press button [1] or [2].  
1
Button [1]: Selects the next lower number disc.  
Button [2]: Selects the next higher number disc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
64  
How to operate the receiver with an optional CD changer connected  
[SEL]  
button  
[DISP FUNC] button  
Buttons [1] to [6]  
Specifying a CD to play  
A CD of your choice is directly selectable out of the loaded discs.  
Press the [SEL] button.  
1
Press a button from [1] to [6].  
2
Buttons  
CD  
1
1
7
2
2
8
3
3
9
4
4
5
5
6
6
10 11 12  
To select a CD from nos. 7 to 12, press the desired button  
considerably longer.  
Switching the display  
Press the [DISP FUNC] button for less than one second.  
1
Each time the button is pressed the following will be displayed  
in order.  
track No./elapsed time ➔ disc No./track No. ➔ clock.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
65  
How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only)  
How to operate the tuner with an optional  
HD RADIO tuner connected (U.S.A. only)  
About HD Radio  
If the optional HD Radio (High Definition Radio) tuner unit is  
connected, terrestrial digital broadcasts can be received. When  
terrestrial digital broadcasts are received, FM reception has the  
same quality as a CD, and AM reception has the same quality as  
conventional FM sound. Depending on the reception status, HD  
Radio can also receive analog broadcasts, which means reception is  
still possible in regions with no digital coverage.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
66  
How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only)  
[FM AM] button  
[SEL] button  
[
] button  
[
] button  
First, press the [FM AM] button to start tuner operation.  
There are automatic and manual methods for setting stations in  
memory. The receiver will accept up to 24 stations in memory: 6 in  
AM and 18 in FM (6 each for FM1, FM2 and FM3.) (Initial setting)  
Tuning to a station  
Press the [FM AM] button for less than one second to  
switch to the desired FM or AM bands.  
1
Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in  
order each time the button is pressed.  
If the optional SIRIUS satellite radio tuner unit is connected, radio  
mode will be switched between the satellite radio mode and FM  
ATTENTION  
AM radio mode by pressing the [FM AM] button for more than  
one second.  
Turn the [SEL] button to the left or right to tune to a  
station.  
2
Turn to the right: Tunes to higher frequencies.  
Turn to the left: Tunes to lower frequencies.  
Press the [ ] or [ ] button to start the automatic station  
search.  
3
[
[
] button: Starts searching toward higher frequencies.  
] button: Starts searching toward lower frequencies.  
At times, it may be difficult to maintain optimum reception  
because the antenna affixed to your vehicle is in motion  
constantly (relative to the broadcast antenna), encountering  
continuous variation in the received radio signal's strength. Other  
factors affecting reception include interference from natural  
obstacles, sign posts, etc.  
ATTENTION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
67  
How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only)  
[FM AM] button  
[SEL] button  
Buttons [ ] to [ ]  
1
6
Entering stations into memory automatically  
(The automatic preset mode: ASM)  
Press the [FM AM] button for less than one second to  
switch to the desired FM or AM bands.  
1
Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in  
order each time the button is pressed.  
If the optional SIRIUS satellite radio tuner unit is connected, radio  
mode will be switched between the satellite radio mode and FM  
ATTENTION  
AM radio mode by pressing the [FM AM] button for more than  
one second.  
Press the [SEL] button for more than two seconds until a  
beep is heard.  
2
The automatic preset mode starts.  
The [ASM ON] indicator on the screen flashes, and stations  
are automatically entered in memory under buttons [1] to [6].  
These buttons are called preset buttons.  
•When a new station is set in memory, the station previously set  
in memory will be deleted.  
ATTENTION  
•If there are fewer than six receivable stations, the stations set in  
the remaining buttons will be retained.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
68  
How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only)  
[FM AM] button  
[SEL] button  
Buttons [ ] to [ ]  
1
6
Manually setting stations into memory  
This section covers the setting of stations in memory under the  
numbered buttons.  
Press the [FM AM] button for less than one second to  
switch between FM and AM.  
1
If the optional SIRIUS satellite radio tuner unit is connected, radio  
mode will be switched between the satellite radio mode and FM  
ATTENTION  
AM radio mode by pressing the [FM AM] button for more than  
one second.  
Turn the [SEL] button to the right or left to tune to the  
station to be entered in memory.  
2
Select any button, from [1] to [6], and press it for more  
than two seconds.  
3
The tuned station is now memorized and set in the button  
selected. Repeat the procedure to set additional manually  
tuned stations in memory, in turn, for buttons [1] to [6]. These  
buttons are called the preset buttons.  
If the vehicle's battery is disconnected (for repairs to the  
vehicle or for removing the receiver), all stations in memory will  
Warning  
be lost. In such a case, set stations in memory again.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
69  
How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only)  
[SEL] button  
Buttons [ ] to [ ]  
1
6
Preset station scan  
This function enables reception of all the stations in the preset  
buttons for five seconds each.  
Press the [SEL] button for less than two seconds.  
1
[P SCAN] will appear at the display, and stations stored under  
preset buttons [1] through [6] will be played for five seconds  
each.  
To stop the preset scan mode at a desired station, press  
the [SEL] button again.  
2
The receiver will stay tuned to the desired station.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
70  
How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only)  
[DISP FUNC] button  
Switching between displays when receiving HD Radio  
During digital reception, the name of the station being received and  
other information can be displayed.  
Press the [DISP FUNC] button for less than one second.  
1
Each time the button is pressed, the display item changes in  
the following order:  
station name ➔ title* ➔ artist* ➔ album* ➔ genre.  
* Depending on the nature of the broadcast, no information  
may be shown.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
71  
How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only)  
[DISP FUNC] button  
[RTN]  
button  
[SEL] button  
HD Radio reception settings  
The HD Radio reception method can be selected. When the HD  
Radio tuner is connected to this deck for the first time, it will be set  
at [AUTO] (automatic digital/analog selection).  
Press the [DISP FUNC] button for more than one  
second.  
1
The function mode is activated.  
Turn the [SEL] button to select HD RADIO.  
2
Press the [SEL] button.  
3
The mode will change to reception setting mode.  
Turn the [SEL] button to select AUTO or OFF.  
4
In the [AUTO] setting, the selection is switched between digital  
and analog reception automatically. In areas where digital  
reception is not possible, reception is automatically switched  
to analog to avoid loss of reception.  
During digital reception, [DIGITAL] is shown on the display.  
This is cleared during analog reception.  
In the [OFF] setting, reception is always analog.  
Press the [SEL] button.  
5
Press the [RTN] button.  
6
At this time, other adjustments can also be made in Function  
Mode.  
Press the [DISP FUNC] or [RTN] to exit Function Mode.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
72  
How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only)  
How to operate the tuner with an optional SIRIUS  
satellite radio tuner connected (U.S.A. only)  
About SIRIUS satellite radio  
If the optional SIRIUS satellite radio tuner unit is connected, satellite  
radio can be received.  
With SIRIUS satellite radio, over 100 channels are available  
including music, sports, news, and entertainment programs.  
The channel can be selected from categories such as POP and  
ROCK, or select a channel by direct input.  
Reception of SIRIUS satellite radio is charged; you have to  
subscribe to it.  
It is possible to subscribe from the SIRIUS radio website.  
URL: http://cdn.sirius.com  
For information about the operation and set-up of the SIRIUS  
satellite radio tuner unit, see the SIRIUS satellite radio unit’s  
ATTENTION  
owner’s manual.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
73  
How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only)  
[FM AM] button  
[SEL] button  
[
[
] button  
] button  
Selecting the radio mode  
Press the [FM AM] button for more than two seconds.  
1
The mode switches between satellite radio mode and FM/AM  
radio mode each time the button is pressed.  
Tuning to a channel  
Press the [FM AM] button for less than one second to  
1
2
3
switch to the desired SR channels.  
Radio bands will switch from SR1 ➔ SR2 ➔ SR3 ➔ SR4 in  
order each time the button is pressed.  
Turn the [SEL] button to the left or right to tune to a  
channel.  
Turn to the right: Tunes to higher channels.  
Turn to the left: Tunes to lower channels.  
Press the [ ] or [ ] button for less than one second to  
start the automatic channel search.  
Reception is enabled for all channels within the currently  
selected category.  
(Refer to page 75 for details on “Category selection”.)  
[
[
] button: Starts searching toward higher channels.  
] button: Starts searching toward lower channels.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
74  
How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only)  
[
] button  
[SEL] button  
Buttons [1] to [3]  
Buttons [5] and [6]  
[
] button  
Category selection  
The channel can be selected from among categories such as POP  
and ROCK. Consult the SIRIUS website for details of categories.  
Press the [ ] or [ ] button for more than one second.  
1
[
[
] button: Advance to next category.  
] button: Return to previous category.  
Direct channel selection  
The channel can be selected by inputting the channel directly.  
Press the [SEL] button for more than two seconds.  
1
The mode will change to direct channel selection mode.  
Press the buttons [1], [2] and [3] to select the channel  
number to be input.  
2
[1] button : Hundreds  
[2] button : Tens  
[3] button : Units  
Each time the buttons are pressed, the numerals change in the  
following order.  
0 ➔ 1 ➔ 2 ➔ 3 ➔ 4 ➔ 5 ➔ 6 ➔ 7 ➔ 8 ➔9  
Pressing the [6] button clears the numeral at the previous digit.  
Press button [5].  
3
Starts reception.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
75  
How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only)  
[SEL] button  
Buttons [ ] to [ ]  
1
6
Manually setting channels into memory  
This section covers the setting of channels in memory under the  
numbered buttons.  
Turn the [SEL] button to the right or left to tune to the  
channel to be entered in memory.  
1
Select any button, from [1] to [6], and press it for more  
than two seconds.  
2
The tuned channel is now memorized and set in the button  
selected. Repeat the procedure to set additional manually  
tuned channels in memory, in turn, for buttons [1] to [6].  
These buttons are called the preset buttons.  
If the vehicle's battery is disconnected (for repairs to the  
vehicle or for removing the receiver), all channels in memory  
Warning  
will be lost. In such a case, set channels in memory again.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
76  
How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only)  
[SEL] button  
Buttons [ ] to [ ]  
[DISP FUNC] button  
1
6
Preset channel scan  
This function enables reception of all the channels in the preset  
buttons for five seconds each.  
Press the [SEL] button for less than two seconds.  
1
[P SCAN] will appear at the display, and channels stored  
under preset buttons [1] through [6] will be played for five  
seconds each.  
To stop the preset scan mode at a desired channel,  
press the [SEL] button again.  
2
The receiver will stay tuned to the desired channel.  
Switching displays when using the SIRIUS  
satellite radio  
Press the [DISP FUNC] button for less than one  
second.  
1
Each time the button is pressed the display item  
changes in the following order:  
channel name ➔ category name ➔ title ➔ artist ➔  
SIRIUS unit ID.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
77  
If you have a question:  
If you have a question:  
[RESET] button  
First check the items mentioned below before attempting to  
troubleshoot problems.  
If a problem occurs, for instance when the unit does not respond  
to any button presses, or the display doesn't work correctly,  
Caution  
press the [RESET] button using a paper clip or similar item.  
Pressing the [RESET] button will delete all the entries from  
memory. The settings will return to those made at the factory  
prior to shipment.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
78  
If you have a question:  
Displayed information (for troubleshooting)  
The information listed in the chart below is displayed to show the  
status of the CD, CD changer and SIRIUS tuner. Refer to the chart  
for the appropriate action.  
Information Contents  
Explanation and remedial action to take  
INFO 2  
INFO 3  
INFO 5  
NO DISC LOADED IN  
THE MAGAZINE  
There is no disc in the magazine or player. Load  
a disc in the magazine. (Load a music disc.)  
DISCS ARE DIRTY OR The loaded disc is dirty or upside down. Check  
DAMAGED  
it for proper orientation and verify it is clean.  
CD PLAYER AND CD  
CHANGER FAILS  
MECHANICALLY  
•
The CD player and CD changer is inoperative for  
some reason. Go through the magazine removal  
procedure.  
•
•
If a magazine fails to eject, have your dealer fix  
the problem.  
INFO 6  
WHEN THE CD PLAYER  
AND CD CHANGER  
INTERNAL TEMPERATURE  
IS HIGH (TO PROTECT  
PICKUP UNIT)  
The temperature in the CD player and CD  
changer is too high for operation. Wait till it  
cools down.  
Resume playing after the “High temperature  
sensed and CD stopped" display disappears. If  
the CD still cannot play, have your dealer  
repair it.  
•
INFO 7  
AN INTERNAL POWER  
SUPPLY FAILURE IS  
OCCURRING  
•
Turn the ACC off once before turning it on once  
again to resume the operation.  
If the function still cannot be restricted, contact  
your dealer.  
•
ANTENNA  
SIRIUS ANTENNA  
IS DISCONNECTED  
Connect the SIRIUS antenna.  
CALL 888-539- NO SUBSCRIPTION  
Subscribe to SIRIUS to receive the service  
by SIRIUS satellite radio.  
SIRIUS  
TO THE SELECTED  
CHANNEL  
ACQUIRING  
SIRIUS SATELITE  
RADIO SIGNAL  
Select another channel.  
RECEIVING FAILS  
LOAD  
CD changer is in the process of verifying the  
presence of CDs after a magazine has been  
inserted into the CD changer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
79  
If you have a question:  
Remedial action  
to take  
Refer  
to page  
Mode  
Problem  
Causes  
Is the volume control up sufficiently?  
Is MUTE functioning?  
Turn up the volume control.  
25  
25  
Cancel MUTE.  
Readjust the fader and  
balance controls to more  
normal positions.  
Dead or  
weak sound  
Is the fader or balance control set  
far to one side?  
27  
Other probable causes include  
broken audio-signal wiring or a  
faulty speaker.  
Have your dealer check  
the problem.  
Are too many electrical items  
installed, causing a lack of power?  
Have your dealer check  
the problem.  
Power does  
not turn on.  
Other probable causes include a  
run-down car battery, broken power  
or interconnection wiring.  
Have your dealer check  
the problem.  
Has the car battery been disconnected  
for repair or checked out?  
Reenter them into  
memory.  
47,  
48  
Common  
to all  
Frequencies Are too many electrical items  
or titles set in installed and causing lack of  
memory are available power?  
deleted.  
Have your dealer check  
the problem.  
Other probable causes include  
run-down car battery, broken power  
or interconnection wiring.  
Have your dealer check  
the problem.  
No guide  
Is the guide tone disabled?  
tone sounds.  
Enable the guide tone.  
Replace battery.  
31  
61  
61  
Is the battery low?  
Is the battery installed in reverse  
polarity?  
Reinstall the battery in the  
correct polarity.  
The remote  
control does  
not work.  
Is direct sunlight hitting the remote  
control light receptor?  
Use the remote control  
close to the receptor.  
Other probable causes include a  
malfunctioning remote control.  
Have your dealer check  
the problem.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
80  
If you have a question:  
Remedial action  
to take  
Refer  
to page  
Mode  
Problem  
Causes  
Is an extra label or seal  
applied to the disc?  
Do not apply labels or seals  
to the disc.  
The disc cannot be inserted.  
The disc is ejected as soon  
as it is inserted.  
12  
Are there rough edges,  
deformations or  
damaged areas on the  
disc?  
Try inserting another disc.  
Removed any burrs.  
Do not use a deformed or  
damaged disc.  
Or, the disc cannot be  
ejected.  
The disc cannot be  
changed.  
13  
Is the disc damaged?  
(scratched, warped, etc.) play a damaged disc.  
Try another disc. Do not  
12  
14  
CD  
Is the disc clean?  
Clean the disc.  
Sound skips around.  
Sound is intermittent.  
Sound is bad in quality.  
Is the player mounted at  
a proper angle?  
Is the player mounted  
loosely?  
Have your dealer check it  
out.  
Are you driving over a  
rough surface?  
Avoid playback while  
driving over rough surfaces.  
11  
Press the [DISC] button a  
bit longer (forced Eject).  
The disc cannot be  
ejected.  
If unknown  
Remedial action  
to take  
Refer  
to page  
Mode Problem  
Causes  
Is the antenna retracted?  
Extend the antenna.  
Is the tuner correctly tuned to a  
station?  
Tune to a station.  
46  
46  
Tune to a local station.  
(Please note, there may  
be no local stations  
servicing the area where  
you are currently driving.)  
Receives  
no  
Are you driving outside the service  
area of your preset stations?  
stations,  
or  
Tuner  
receives  
static  
noise.  
Are you operating other equipment  
with a computer, or a mobile phone,  
in your vehicle at the same time as  
your receiver?  
Avoid operating such  
equipment while using  
the receiver.  
Other problems may include a loose Have your authorized  
or disconnected antenna cable, a  
bad antenna cable or a bad  
Eclipse retailer check the  
problem.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
81  
Specifications  
Specifications  
<GENERAL>  
Power Supply  
Current Drain  
14.4V DC (11-16V)  
3A  
Dimensions (W x H x D)  
In-Dash Unit  
Mass (weight)  
7" x 2" x 6-1/8" (178 x 50 x 155mm)  
Approx. 1.4kg  
Usage temperature range  
Storage temperature range  
-20°C to + 65°C (-4°F to 149°F )  
-40°C to + 85°C (-20°F to 185°F )  
<FM TUNER>  
Frequency Range  
USA:  
87.75~107.9MHz (0.2MHz step)  
87.5~108MHz (0.05MHz step)  
87.5~108MHz (0.1MHz step)  
87.75~107.9MHz (0.1MHz step)  
13dBf  
14dBf  
30~15,000Hz, 3dB  
38dB (1kHz)  
Asia:  
Australia:  
Latin America:  
Usable Sensitivity  
50dB Quieting Sensitivity  
Frequency Response  
Stereo Separation  
<AM TUNER>  
Frequency Range  
USA:  
Asia:  
Australia:  
Latin America:  
Usable Sensitivity  
530~1,710kHz (10kHz step)  
522~1,629kHz (9kHz step)  
522~1710kHz (9kHz step)  
530~1710kHz (10kHz step)  
20µV  
<CD SECTION>  
Frequency Response  
Wow & Flutter  
20~20,000Hz, 3dB  
Below measurable limits  
Stereo Separation  
S/N Ratio (A-weighted)  
Dynamic Range  
80dB  
95dB  
95dB  
Total Harmonic Distortion  
0.008%  
<AUDIO AMPLIFIER>  
Power Output  
14W x 4 (20Hz~20kHz, 1% THD,  
4Ω, Vcc=14.4V) Max 50W x 4  
5V/55Ω line-out impedance  
Output Level/Impedance  
Tone Action  
Bass  
:
12dB at 80Hz  
Middle : 12dB at 630Hz  
Treble : 12dB at 10kHz  
Loudness  
+10dB at 100Hz/+6.5dB at 10kHz  
Download from Www.Somanuals.com. All Manuals Search And Download.  
82  
Before installation  
Before installation  
ꢀ Note ꢀ  
Be sure to disconnect the vehicle battery's negative terminal  
before installing the receiver.  
Components  
No.  
Item  
Main unit  
Mounting sleeve  
Side bracket  
Rear bracket  
Q'ty  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
1
1
2
1
1
1
1
1
4
4
1
1
1
1
Bezel  
Bushing  
Self-tapping screw (6 x 16 mm)  
Stud bolt  
Flat head screw (red: 5 x 8 mm)  
Hex-head bolt (red: 5 x 8 mm)  
Hex-head bolt (6 x 20 mm)  
Hex nut (5 mm)  
Hex nut (6 mm)  
Interconnecting cable  
Installation angle  
In order to maintain proper functioning, install the unit within an angle  
of 30 degrees from horizontal (standard). If this is not done, sound  
skipping or ejection of the CD may occur.  
FRONT  
WITHIN AN ANGLE  
OF 30 DEGREES  
STANDARD  
Download from Www.Somanuals.com. All Manuals Search And Download.  
83  
Mounting instruction  
Mounting instruction  
Mounting the main unit  
-If installing the main unit by the mounting sleeve-  
Insert the mounting sleeve into the opening in the vehicle  
dash board or console box.  
1
Use a screwdriver or the like to bend the tabs in the  
mounting sleeve to secure the mounting sleeve.  
2
BEND THE MOUNTING  
TABS.  
DASH BOARD  
OR CONSOLE BOX  
2 MOUNTING  
SLEEVE  
Attach the side brackets to the main unit using flathead  
screws.  
3
1 MAIN UNIT  
9 FLAT HEAD  
SCREWS [ x 2 ]  
(red: 5 x 8mm)  
3
SIDE BRACKETS [ x 2 ]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
84  
Mounting instruction  
Mount the stud bolt to the main unit.  
4
5
Insert the main unit into the mounting sleeve until it locks  
in place.  
Fasten the rear of the main unit using either method [A]  
or [B].  
6
Select method [A] or [B] to suit the interior configuration of the  
vehicle.  
Install the bezel on the main unit.  
7
[A]  
METAL OF  
VEHICLE  
DASH BOARD  
OR CONSOLE BOX  
6
BUSHING  
8
STUD BOLT  
2
MOUNTING SLEEVE  
5
BEZEL  
[B]  
7 SELF TAPPING  
13  
HEX NUT (6mm)  
SCREW (6 x 16mm)  
11  
HEX  
HEAD  
BOLT  
(6 x 20mm)  
DASH BOARD  
OR CONSOLE BOX  
METAL OF  
VEHICLE  
12  
HEX NUT (5mm)  
4
REAR BRACKET  
8
STUD BOLT  
2
MOUNTING SLEEVE  
5
BEZEL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
85  
Mounting instruction  
-If installing the main unit by the side brackets of the vehicle-  
Remove the pocket and any other accessories from the  
center cluster to make room for the main unit.  
1
2
Remove the mounting side brackets for the pocket.  
CENTER CLUSTER  
POCKET  
SCREWS  
3
Attach the side brackets to the main unit.  
4
Install the main unit in the vehicle.  
1
MAIN UNIT  
POCKET  
10  
HEX HEAD BOLT  
(red: 5 x 8mm)  
SCREWS [x4]  
SIDE BRACKETS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
86  
Mounting instruction  
Names of lead wires and destinations (refer to Page 89)  
ꢀ Caution ꢀ  
Never connect the power supply to the speaker leads,  
otherwise it cause damage to the main unit.  
ꢀ Note ꢀ  
To prevent unconnected leads from shorting out, insulate them  
by wrapping their tips with electrical tape. Similarly, insulate the  
ends of connected leads.  
If an external amplifier is to be connected to the receiver, be  
sure to ground its outside housing to the vehicle body (a metal  
part).  
No.  
1
Name  
ACC  
Wire color  
Red  
Destination  
Connect where the power comes on  
when the ignition is in the ACC  
position.  
2
B+  
Yellow  
Black  
Connect where the power is  
constantly available, regardless of the  
ignition switch's position.  
3
4
5
6
Ground  
Connect where good body  
grounding is available.  
Antenna power supply Blue  
Connect to the automatic-antenna  
control terminal of the vehicle.  
Illumination power supply Orange/White  
Control power supply Blue/White  
Connect to where power comes on  
when the headlights are turned on.  
Connect to the control terminal for  
the external amplifier, or to the RCA  
output connectors of a DSP or EQ.  
7
E-LAN terminal  
Connect to the E-LAN terminal of the  
CD changer, DSP, etc.  
8 & 9 Line-out terminals  
Connect to the RCA input connectors  
of an external amplifier.  
10  
11  
Line-out terminals (Nonfader)  
Connect to the RCA input connectors of  
a DSP or EQ, or the RCA connectors of  
a woofer amplifier.  
Speaker leads  
Connect them to their respective  
speaker leads.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
87  
Mounting instruction  
System  
CD5415  
CD5415  
CH3083  
CD5415  
CH3083  
CH3083  
CD5415  
HDR105  
HD RADIO TUNER  
CH3083  
Download from Www.Somanuals.com. All Manuals Search And Download.  
88  
Mounting instruction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
89  
Mounting instruction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
90  
Mounting instruction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
91  
Mounting instruction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
92  
How to contact customer service  
How to contact customer service  
Should the product require service, please contact your nearest  
following Eclipse dealer.  
<U.S.A/CANADA>  
DIVISION OF FUJITSU TEN CORP. OF AMERICA  
19600 SOUTH VERMONT AVENUE, TORRANCE, CA 90502  
Phone: (310) 327-2151  
<AUSTRALIA>  
FUJITSU TEN (AUSTRALIA) PTY LTD.  
ECLIPSE AUSTRALIA  
Phone: 1800-211-411  
<MALAYSIA>  
Cobra Malaysia Sdn, bhd.  
Level 5, Axis Plaza, Jalan U1/44, Glenmarie, 40150 Shah Alam,  
Selangor D.E., Malaysia.  
Phone: 03-5569-4200  
Fax: 03-5569-4201  
<SINGAPORE>  
Cobra Singapore Pte Ltd  
Trademart  
60, Martin Road, # 05-20, Singapore 239065  
Phone: 6737 2568  
Fax : 6737 9538  
Download from Www.Somanuals.com. All Manuals Search And Download.  
93  
How to contact customer service  
<KOREA>  
Transpectra Co., Ltd.  
115-16 nonhyun dong kangnam ku Seoul, Korea.  
Phone: 02-540-4595  
Fax: 02-2-540-4666  
HYUNDAI AUTONET Co., LTD.  
1st FL. Namhyoung Bldg, 746-23 Yeoksam-Dong, Kangnam-Ku,  
Seoul, Korea 135-080  
Phone: 02-508-6001  
Fax: 02-2-508-6067  
<TAIWAN>  
Sentrek Taiwan, LTD.  
1, 9F, Lane 155, Section 3, Peishen RD., Shenkeng, Taipei Hsien,  
222  
Taiwan, R.O.C.  
Phone: 02-2662-8110  
Fax: 02-2662-8117  
<THAILAND>  
Sho-Ten Co., Ltd.  
114/9 Soi Suwansawadi, Thungmahamek, Rama 4 Rd., Sathorn,  
Bangkok 10120, Thailand.  
Phone: 02-671-9610-12  
Fax: 02-671-9614  
Download from Www.Somanuals.com. All Manuals Search And Download.  
94  
IMPORTANT  
RECORD YOUR “KEY CD”  
HERE…  
STORE YOUR “KEY CD”  
ALONG WITH YOUR  
OWNER’S MANUAL  
TAKE THIS OUT.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
95  

Cobra Digital Digital Camera DCA1620 User Manual
Craftsman Garage Door Opener 1395391 User Manual
Crown Boiler Boiler 16 325 500506 User Manual
Cypress Computer Hardware CY7C68033 User Manual
Delta Electronics Power Supply S24SA User Manual
Ducane Gas Grill 1605NG User Manual
Dymo Scale P100S User Manual
EAW DJ Equipment MX8750 User Manual
Fisher CRT Television PC 25S00 PC 27S90 User Manual
GE Answering Machine 347A8232 0001 User Manual