DMP Electronics Home Security System XR500 User Manual

Programming guide

Xr500 SerieS Canadian

Command ProCeSSor™ Panel

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of ConTenTS

1.1

Before you Begi n ................................................................. 1

Programming Information Shee t ........................................... 1

Getting Starte d .................................................................... 1

Encrypted Communications (XR500N/XR500E only)................ 2

Programmer Operation......................................................... 2

Programmer Lockout Codes.................................................. 2

Reset Timeou t ..................................................................... 2

Power U p ............................................................................ 3

Keypads ............................................................................. 3

Special Key s ........................................................................ 3

Entering Alpha Characters .................................................... 4

Entering Non-Alpha Characters ............................................. 4

Keypad Displays Current Programmin g .................................. 4

Multiple Displays.................................................................. 5

Asterisks in Programmin g ..................................................... 5

Initialization......................................................................6

Initialization ........................................................................ 6

Clear All Memory ................................................................. 6

Clear All Codes .................................................................... 6

Clear All Schedules .............................................................. 6

Clear Display Events Memory................................................ 6

Clear Zone Information ........................................................ 6

Clear Area Information......................................................... 6

Clear Output Information ..................................................... 6

Clear Communication and Remote Options ............................ 7

Set to Factory Default s ......................................................... 7

Communicatio n .................................................................8

3.1

Communication ................................................................... 8

Account Number.................................................................. 8

Transmit Delay .................................................................... 8

Communication Pat h ............................................................ 8

Communication T y pe............................................................ 8

Path Type............................................................................ 9

T e st Report ......................................................................... 9

T e st Frequenc y .................................................................... 9

T e st Day ............................................................................. 9

T e st Tim e ............................................................................ 9

Check In ............................................................................. 9

Fail Tim e ............................................................................. 9

Encryption (XR500E only)..................................................... 9

Receiver IP.......................................................................... 9

Receiver Por t ......................................................................10

First T e lephone Number ......................................................10

Second T e lephone Numbe r ..................................................10

Advanced Programming ......................................................10

First GPRS APN / Second GPRS AP N .....................................10

Fail Test Hours....................................................................10

Protocol ............................................................................10

Retry Seconds ....................................................................11

Substitution Code ...............................................................11

232 Communication Port .....................................................11

232 Setup String.................................................................11

893A..................................................................................11

Alarm Switc h ......................................................................11

Duplicate Alarms.................................................................11

Alarm Reports ....................................................................12

Supervisory/T rouble Report s ................................................12

Opening/Closing and User Report s .......................................12

Door Access Report.............................................................12

Send Communication T rouble ..............................................12

Send Path Information ........................................................12

Network Options (XR500N/XR500E only) ........................... 13

4.1

4.2

DHCP Mode Enabled ...........................................................13

Local IP Addres s .................................................................13

XR500 Series Canadian Programming Guide

Digital Monitoring Products

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of ConTenTS

Gateway Addres s ................................................................13

Subnet Mask ......................................................................13

DNS Server ........................................................................13

Passphrase (XR500E only )...................................................13

Messaging Setu p .............................................................14

5.1

Messaging Setup ................................................................14

Enable Messagin g ...............................................................14

System Nam e .....................................................................14

Destination 1......................................................................14

Destination 1 User Number .................................................14

Destination 2......................................................................14

Destination 2 User Number .................................................14

Destination 3......................................................................14

Destination 3 User Number..................................................15

Email Communication T y pe..................................................15

O/C Email ..........................................................................15

O/C SM S ............................................................................15

Monthly Limit .....................................................................15

SMTP Server ......................................................................15

SMTP Server Port................................................................15

SMTP Username .................................................................15

SMTP Passwor d ..................................................................15

From Email Addres s ............................................................15

Device Setup ...................................................................16

6.1

Device Setu p ......................................................................16

Device Number...................................................................16

Door Name .......................................................................16

Access Area s ......................................................................16

Egress Areas ......................................................................16

Display Areas .....................................................................17

Strike Time.........................................................................18

Strike Delay........................................................................18

Fire Exit Releas e .................................................................18

Output Grou p .....................................................................18

Schedule Override ..............................................................18

Auto Force Arm Device? ......................................................18

Door Real-Time Status ?.......................................................18

Send Door Forced Message?................................................18

Program 734 Option s ..........................................................19

6.15.1 Activate Zone 2 Shun t .........................................................19

6.15.2 Zone 2 Soft-Shunt Time ......................................................19

6.15.3 Relock on Zone 2 Fault? ......................................................19

6.15.4 Activate Zone 3 Request to Exit ..........................................19

6.15.5 Zone 3 REX Strike Time.......................................................19

6.15.6 Activate Onboard Speaker ...................................................20

6.15.7 Card Option s ......................................................................20

6.15.8 Custom Card Deﬁnition s ......................................................20

6.15.8.1 Site Code Positio n ...............................................................20

6.15.8.2 Site Code Lengt h ................................................................20

6.15.8.3 User Code Position..............................................................20

6.15.8.4 User Code Lengt h ...............................................................20

6.15.9 Require Site Cod e ...............................................................21

6.15.9 . Site Code Display................................................................21

6.15.10 Number of User Code Digits ................................................21

6.15.11 Degraded Mod e ..................................................................21

Remote Options ..............................................................22

7.1

Remote Options..................................................................22

Remote Key .......................................................................22

Remote Disarm ..................................................................22

Allow Dialer Remote............................................................22

Armed Answer Rings...........................................................22

Disarmed Answer Rings.......................................................22

PC Modem ........................................................................23

Manufacturer Authorizatio n .................................................23

Allow Network Remot e ........................................................23

Network Programming Port..................................................23

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of ConTenTS

7.5.2

7.6

Encrypt Network Remote.....................................................23

Allow Cellular Remote .........................................................23

First GPRS APN / Second GPRS AP N .....................................23

Encrypt Cellular Remot e ......................................................23

Allow RS-232 Remote..........................................................23

Entré Connectio n ................................................................23

Entré Incoming TCP Por t .....................................................23

Entré IP Address.................................................................23

Entré Outbound TCP Port ....................................................23

Entré Backup IP Addres s .....................................................24

Entré Backup TCP Por t ........................................................24

Entré Checki n .....................................................................24

Entré Passphras e ................................................................24

Send Local Changes............................................................24

Remote Change IP..............................................................24

Remote Change Por t ...........................................................24

Remote T e lephone Number .................................................24

System Reports...............................................................25

System Reports ..................................................................25

Abort Report ......................................................................25

Restoral Report s .................................................................25

Bypass Reports...................................................................25

Schedule Change Reports....................................................25

Code Change Reports .........................................................25

Access Keypad s ..................................................................25

Ambush ............................................................................26

Panic T e st Communication (XR500N/XR500E only) ...............26

System Option s ...............................................................27

9.1

System Options ..................................................................27

System ..............................................................................27

Instant Arming ...................................................................27

Closing Wai t .......................................................................27

Entry Delay 1 .....................................................................27

Cross Zone Time.................................................................28

Zone Retard Dela y ..............................................................28

Power Fail Dela y .................................................................28

Swinger Bypass T r ips ..........................................................28

Reset Swinger Bypass .........................................................28

Time Zone Change s ............................................................28

Latch Supervisory Zones......................................................29

Programming Menu Language ............................................29

User Menu and Status List Language ...................................29

Bypass Limit.......................................................................30

Card Plus PIN (XR500E only) ...............................................30

House Code........................................................................30

Detect Wireless Jamming ....................................................30

Wireless Audible Annunciation .............................................31

Enable Keypad Panic Keys ...................................................31

Occupied Premises..............................................................31

Enhanced Zone T e st............................................................31

Dual EOL............................................................................31

Send 16 Character Name s ...................................................31

Bell Options.....................................................................32

Bell Options........................................................................32

Bell Cutoff Time..................................................................32

Automatic Bell T e st ............................................................32

Bell Output.........................................................................32

Bell Action..........................................................................32

10.5.1 Fire Bell Action ...................................................................32

10.5.2 Burglary Bell Action.............................................................32

10.5.3 Supervisory Bell Action........................................................32

10.5.4 Panic Bell Actio n .................................................................32

10.5.5 Emergency Bell Action.........................................................32

10.5.6 Auxiliary 1 Bell Action..........................................................32

10.5.7 Auxiliary 2 Bell Action..........................................................32

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

iii

Table of ConTenTS

Output Options................................................................33

11.1

Output Options...................................................................33

11.2.1 Cutoff Output ....................................................................33

11.2.2 Output Cutoff Tim e .............................................................33

11.3

Communication T rouble Output............................................33

Fire Alarm Outpu t ...............................................................33

Fire T rouble Output.............................................................33

Panic Alarm Output.............................................................34

Ambush Outpu t ..................................................................34

Entry Output ......................................................................34

Exit Output.........................................................................34

Ready Outpu t .....................................................................34

T e lephone T rouble Output ...................................................34

Late T o C lose Output ..........................................................34

Device Fail Output ..............................................................34

Sensor Reset Outpu t ...........................................................34

Closing Wait Outpu t ............................................................35

Arm-Alarm Output ..............................................................35

Output Information ........................................................36

Output Informatio n .............................................................36

Output Number .................................................................36

Output Name .....................................................................36

Output Real-Time Status .....................................................36

Serial Number ....................................................................36

Supervision Tim e ................................................................36

Output Groups ................................................................37

Output Groups....................................................................37

Group Number....................................................................37

Group Name ......................................................................37

Output Number ..................................................................37

Menu Display...................................................................38

Menu Display .....................................................................38

Armed Status .....................................................................38

Time .................................................................................38

Arm/Disarm........................................................................38

Status List .......................................................................39

Status List .........................................................................39

Display Keypads .................................................................39

System Monitor T rouble s .....................................................39

Fire Zone s ..........................................................................39

Burglary Zones ...................................................................40

Supervisory Zones ..............................................................40

Panic Zones........................................................................40

Emergency Zones ...............................................................40

Auxiliary 1 Zones ................................................................40

Auxiliary 2 Zones ................................................................40

Communication T rouble.......................................................40

Printer Reports ...............................................................41

Printer Reports ...................................................................41

Arm and Disarm Reports .....................................................41

Zone Reports......................................................................41

User Command Reports.......................................................41

Door Access Report s ...........................................................41

Supervisory Report s ............................................................41

PC Log Reports................................................................42

PC Log Reports...................................................................42

Communication T y pe...........................................................42

Net IP Address ...................................................................42

Net Por t .............................................................................42

232 Communication Port .....................................................42

232 Setup ..........................................................................42

Arm and Disarm Reports .....................................................42

Zone Reports......................................................................42

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of ConTenTS

17.9

User Command Reports.......................................................42

17.10

17.11

17.12

Door Access Report s ...........................................................43

Supervisory Report s ............................................................43

PC Log Real-Time Status .....................................................43

Area Information ............................................................44

Area Information ................................................................44

Exit Delay...........................................................................44

Burglary Bell Output............................................................44

Opening/Closing Report s .....................................................44

Closing Check.....................................................................45

Closing Code ......................................................................45

Any Bypass ........................................................................45

Area Schedules...................................................................45

Early Morning Ambush (XR500N/XR500E only) ....................45

Area Number......................................................................45

18.10.1 All/Perimeter Programming..................................................45

18.10.2 Home/Sleep/Away Programming..........................................46

Area Nam e .........................................................................46

Account Number.................................................................46

Automatic Armin g ...............................................................46

Bad Zone s ..........................................................................46

Automatic Disarming...........................................................46

Armed Output Number........................................................47

Late Output Numbe r ...........................................................47

Late Arm Delay...................................................................47

Bank Safe & Vault (XR500N/XR500E only) ............................47

Common Area ....................................................................47

Arm First Are a ....................................................................47

T w o Man Rule (XR500N/XR500E only )..................................47

Zone Information............................................................48

Zone Information................................................................48

Zone Number .....................................................................48

Zone Name ........................................................................48

Zone Typ e ..........................................................................49

Area Assignment.................................................................49

Fire Bell Output ..................................................................49

Arming Zone Area Assignmen t .............................................50

Styl e ..................................................................................50

Next Zon e ..........................................................................51

Wireles s .............................................................................51

19.10.1 Serial Number Entry............................................................51

19.10.2 Contac t ..............................................................................51

19.10.3 Supervision Tim e ................................................................52

19.10.4 LED Operatio n ....................................................................52

19.10.5 Disarm/Disabl e ...................................................................52

19.10.6 PIR Pulse Count..................................................................52

19.10.7 PIR Sensitivity ....................................................................52

1100 Series Key Fob s ........................................................................53

19.11.1 Key Fob User Number ............................................. 53

19.11.2 Key Fob Serial Number........................................................53

19.11.3 Key Fob Supervision Time ...................................................53

19.11.4 Number of Key Fob Buttons ...................................... 53

19.11.5 Key Fob Button Selection (Four Buttons)...............................53

19.11.6 Key Fob Button Selection (T w o Buttons) ........................ 53

19.11.7 Button Action .....................................................................54

19.11.8 Button Press Time ..............................................................54

19.11.9 Arm/Disarm Area Selection..................................................54

19.11.10 Output Number ..................................................................55

19.11.11 Output Actio n .....................................................................55

19.11.12 Next Zon e ..........................................................................55

19.12

Wireles s .............................................................................56

19.12.1 Check-in Time ....................................................................56

19.12.2 Internal Contact .................................................................56

19.12.3 End-of-Line ........................................................................56

19.12.4 Normally Open ..................................................................56

19.12.5 Next Zon e ..........................................................................56

XR500 Series Canadian Programming Guide

Digital Monitoring Products

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of ConTenTS

Alarm Action.......................................................................56

Disarmed Open .................................................................56

Report to Transmi t ..............................................................57

Output Number ..................................................................57

Output Actio n .....................................................................57

Swinger Bypass ..................................................................58

Prewarn Keypad Addresses..................................................58

Entry Delay ........................................................................58

Zone Retard Dela y ..............................................................58

Presignal Keypad Addresses ................................................58

Fast Response ....................................................................58

Cross Zon e .........................................................................58

Priority ..............................................................................59

Fire Panel Slave Input ........................................................59

Area Follower .....................................................................59

Zone Real-Time Status ........................................................59

19.28.1 Door Number .....................................................................59

19.29

19.30

Zone Audit Days .................................................................59

Report with Account Number for Area ..................................59

Stop.................................................................................60

20.1

Stop ..................................................................................60

Set Lockout Code ............................................................60

21.1

Set Lockout Code................................................................60

Feature Upgrade .............................................................61

22.1

Feature Upgrade.................................................................61

22.1.1 Encryption..........................................................................61

22.1.2 All No Yes Option................................................................61

22.1.3 Service User Authenticatio n .................................................61

Purchasing Feature Upgrades ..............................................61

Appendi x .........................................................................62

23.1

False Alarm Reduction.........................................................62

System Recently Armed report.............................................62

Diagnostics function............................................................62

Using the 984 Command Function........................................64

Keypad Displays .................................................................64

Using the Walk T e st ............................................................65

Walk Test ..........................................................................65

Zone Types.........................................................................65

T r ip Counter For Walk T e st ..................................................65

T r ip Counter For DMP Wireless Check-in T e st (WLS) ..............66

T e st End Warning ...............................................................66

Local Printer for Walk T e s t ...................................................66

Keypad Speaker Operation ..................................................66

Cross Zoning ......................................................................67

Events Manager..................................................................67

User Proﬁle s .......................................................................67

User Proﬁles Record ............................................................67

FA Series Transmitter Informatio n ........................................68

Cross T a lk ..........................................................................68

23.10.1 Wireless Check-in and Supervision Deﬁnition s ..........................

23.11

23.12

Keypad Bus and LX-Bus Zone Type Description s....................69

Zone Type Speciﬁcations ....................................................69

23.12.1 Keypad Bus Zone Type Defaults .............................................70

23.14 Area Account Number Messages .............................................73

Revisions to This Document............................................74

Listings and Approvals ......................................................................75

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

This page intentionally left blank.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

vii

inTroduCTion

Introduction

1.1

Before you Begin

This guide provides programming information for the DMP XR500, XR500N, and XR500E Command

Processor™ Panel. After this Introduction, the remaining sections describe the functions of each

programming menu item along with the available options. Before starting to program, we recommend

that you read through the contents of this guide. The information contained here allows you to quickly

learn the programming options and operational capabilities of the XR500, XR500N, and XR500E panels.

In addition to this guide, you should also read and be familiar with the following XR500 Series Canadian

documents:

• XR500 Series Canadian Installation Guide (LT-0681CAN)

• XR500 Series Canadian Programming Sheet (LT-0678CAN)

• XR100/XR500 Canadian Security Command^®User’s Guide (LT-0683CAN)

Internal Programmer

The panel contains all of its programming information in an on-board processor and does not require an

external programmer. You can perform all programming tasks through a 32-character DMP alphanumeric

keypad set to address one.

Programming Information Sheet

Included with each panel are the Programming Information Sheets. These list the various programming

prompts and available options for programming the panel. Before starting to program, we recommend you

completely ﬁll out each sheet with the programming options you intend to enter into the panel.

Having completed programming sheets available before entering data helps prevent errors and can shorten

the time you spend programming. Completed sheets also provide you with an accurate panel program

record you can keep on ﬁle for future system service or expansion. The remainder of this Introduction

provides instructions for starting and ending a programming session using the alphanumeric keypad.

1.2

Getting Started

Ground Yourself Before Handling the Panel! Touch any grounded metal, such as the enclosure, before

touching the panel to discharge static.

Remove All Power From the Panel! Remove all AC and Battery power from the panel before installing or

connecting any modules, cards, or wires to the panel.

Before starting to program the XR500 Series Canadian panel, make sure the panel is properly grounded and

AC and battery power is applied to the appropriate panel terminals. All wiring connections and grounding

instructions are detailed in the XR500 Series Canadian Installation Guide (LT-0681).

(LT-0759).

Accessing the Programmer

1. Install the reset jumper across the two J16

Phone Line

Tamper

Interface

Card

reset pins for two seconds.

2. Remove the reset jumper and place it over just

one pin for future use.

3. Enter the code 6653 (PROG) into a

32-character alphanumeric keypad set

to address one, supervised mode. Press

COMMAND.

Link LED

Activity LED

Expansion

Connector

Momentarily place the Reset

jumper over both of the J16

pins to reset the panel.

Ethernet

J21

J23

Power

LED

RS-232

J22

LX-Bus

OVC

Output 1

Output 2

J10

Battery

Start

J11

J16

Reset

PROG

Outputs 3-6

AC AC +B –B BELLGND RED YEL GRN BLK SMK GND Z1 GND Z2 Z3 GND Z4 Z5 GND Z6 Z7 GND Z8 Z9+ Z9– Z10+Z10–

4. The keypad displays PROGRAMMER.

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

You are now ready to start programming the panel.

Figure 1: XR500 Series Canadian Panel Showing Reset

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

inTroduCTion

1.3

Encrypted Communications (XR500N/XR500E only)

Some installations require secure data communications. DMP offers NIST approved AES encrypted

communication. Use a unique passphrase to enable encrypted communications and provide a secure

means for data communications. See Network Options.

An XR500E panel communicates using AES encryption. If you currently have an XR500N panel installed, you

may purchase a separate feature key to activate encrypted communications using the Feature Upgrade

process. Encrypted communication cannot be enabled on a standard XR500 panel. For more information

on the Feature Upgrade process see Section 21 in this document.

1.4

Programmer Operation

There are 21 programming sections to choose from:

Programming Item

Initialization

Section in This Manual

Programming Item

Output Information

Output Groups

Menu Display

Section in This Manual

Communication

Network Options

Messaging Setup

Device Setup

Status List

Printer Reports

PC Log Reports

Area Information

Zone Information

Stop

Remote Options

System Reports

System Options

Bell Options

Output Options

Set Lockout Code

Feature Upgrade

To choose a section for programming, press any top row Select key when the keypad displays the name of

that section. Sections 2 through 22 contain detailed instructions for each programming step.

1.5

Programmer Lockout Codes

The panel allows you to enter the programming function without entering a lockout code using steps

1 to 4 listed in Getting Started. We recommend, however, that you install a Lockout Code to restrict

programming to only those persons your company authorizes. You can do this by using the SET LOCKOUT

CODE feature in the Programmer. The Lockout Code restricts any unauthorized panel programming.

After resetting the panel and entering the code 6653, the keypad displays PROGRAMMER. Press COMMAND

to advance through the programming sections until SET LOCKOUT CODE displays (after STOP). Press any

top row Select key. The keypad displays ENTER CODE: – . Enter a 3 to 5 digit Programmer Lockout Code

and press COMMAND. The keypad displays ENTER AGAIN followed by ENTER CODE: –. Enter the same 3 to

5 digit code a second time and press COMMAND. The keypad displays CODE CHANGED.

Note: The panel does not accept a 5-digit Lockout Code higher than 65535.

Before accessing programmer functions enter the new code number. Write the Lockout Code number down

and keep it in a secure place with access limited to authorized persons only. Lost Lockout Codes require

the panel to be sent back to DMP for repair. You may cancel a Lockout Code by entering 00000 at the Set

Lockout Code command.

1.6

Reset Timeout

The panel has a feature that requires you to enter the Programmer within 30 minutes of resetting the

panel. After 30 minutes, if you attempt to program by entering the 6653 (PROG) code, the keypad

displays: RESET PANEL. You must reset the panel and enter the program code then begin programming

within the next 30 minutes.

If you are already in the Programmer and do not press any keys on the programming keypad for 30

minutes, the panel terminates programming. All data entered up to that time is Not saved unless you run

the Stop routine.

Note: Use the Stop routine to exit panel Programming. Ensure the keypad displays “SAVING PROGRAM” to

save all programming changes entered.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

inTroduCTion

1.7

1.8

Power Up

When the XR500 Series Canadian panel is powered up after an AC power failure, any zone transitions are

not recognized for 60 seconds. Normal zone processing resumes at the end of the 60 seconds.

Keypads

DMP offers multiple keypads in a variety of styles. All DMP keypads provide the same programming

capabilities. Each keypad and its operation are shown and described in the following sections.

32-Character Display

Power LED

Armed LED

Power LED

Armed LED

ABC PRINTING

FR I 2 : 51 AM

JONES RESIDENCE

FRI

12:51 PM

Select Keys

A B C

D EF

J KL

Backlit Logo

and Proximity

Antenna

VWX

S T U

COMMAND

COMMAND Key

Back Arrow Key

COMMAND Key

Back Arrow Key

Data Entry Digit keys

Figure 3: Security Command Keypad

Figure 4: Thinline/Aqualite Keypad

1.9

Special Keys

The following special keys/areas are common to all DMP keypads.

COMMAND (CMD) Key

Pressing the COMMAND key allows you to go forward through the programming menu and through each

step of a programming section. As you go through the programming, the keypad display shows any current

programming already stored in the panel memory. If no change is required for a prompt, press the

COMMAND key to advance to the next step.

The COMMAND key is also used to enter information into the panel’s memory such as phone numbers or

zone names. Press the COMMAND key after entering information.

Back Arrow (<—) Key

Use the Back Arrow key to back up one step while programming. The Back Arrow key is also used when

an error is made while entering information. Press the Back Arrow key once to erase the last character

entered.

Select Keys/Areas

The top row of keys are called the Select keys on Security Command, Thinline, and Aqualite keypads.

Each time you need to press a Select key, the keypad displays the function or options above one of the

keys or in the Select Area. Displaying choices above individual Select keys or in Select Areas allows them

to be used for many different applications. For example, you can enter AM or PM when programming the

automatic test time or answer YES or NO for a system option.

During programming, the Select keys/areas also allow you to change information currently in panel

memory by pressing the appropriate Select key/area under or on the display. You then enter the new

information using the keypad data entry digit keys.

When there are more than four response options available, press the COMMAND key to display the next one

to four options. Pressing the Back Arrow key allows you to review the previous four choices.

The Select keys/areas are also used for choosing a section from the programming menu. Press any Select

key or touch the Select Area when the programming section name you want displays.

Note: On Security Command, Thinline and Aqualite keypads, when instructed to press the ﬁrst Select

key, press the far left Select key; the second Select key is the second from the left; third Select key is

second from the right; and the fourth Select key is the far right key. See Figures 6 and 7.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

inTroduCTion

1.10 Entering Alpha Characters

Some options during programming require you to enter alpha characters. To enter an alpha character,

press or touch the key that has that letter written below it. The keypad displays the number digit of the

key. Next, press the Select key/area that corresponds to the location of the letter under the key. Pressing

a different Select key/area changes the letter. When another digit key is pressed, the last letter displayed

is retained and the process starts over.

(

First Letter

Second Letter

Third Letter

Special Character

First Letter Second Letter Third Letter Special Character

Figure 5: Security Command Select Keys

Figure 6: Thinline/Aqualite Select Keys

1.11 Entering Non-Alpha Characters

To enter a space in an alpha entry, press the 9 digit key followed by the third Select key/area. The three

characters on the 9 digit key are Y, Z, and space. You can also enter the following characters: – (dash),

. (period), * (asterisk), and # (pound sign) using the 0 (zero) key and the four Select keys/areas from left

to right. For example, to enter a – (dash), press the 0 (zero) key and then the left Select key/area. A

dash now appears in the keypad display. Figures 7 and 8 show the character location for

Security Command, Thinline, and Aqualite keypads.

CMD

Figure 7: Security Command

Special Characters

Figure 8: Thinline/Aqualite

Special Characters

1.12 Keypad Displays Current Programming

Each programming prompt displayed at the keypad shows the currently selected option in the panel

memory. These options are either shown as a number, a blank, or a NO or YES. To change a number or

blank to a new number, press any top row Select key or touch any Select Area. The current option is

replaced with a dash. Press the number(s) on the keypad you want to enter as the new number for that

prompt. It is not necessary to enter numbers with leading zeros. The panel automatically right justiﬁes

the number when you press the COMMAND key.

To change a programming prompt that requires a NO or YES response, press the Select key or touch the

Select Area for the response not selected. See Figure 12.

For example, if the current prompt is selected as YES and you want to change it to NO, on Security

Command, Thinline, or Aqualite keypads press the third top row Select key. The display changes to NO.

Press the COMMAND key to display the next prompt.

Press the black colored top

row Select key/area.

The keypad displays the new

selection. Press CMD to advance.

THEN

Security

Command

Keypads

BELL TST

YES

Thinline

Aqualite

Keypads

BELL TST

YES

BELL TST

Figure 9: Changing the Current Programming Option

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

inTroduCTion

1.13 Multiple Displays

For many programming and user options, such as Area selections, Menu Displays, and Status Lists, there

are several displays containing programming. For example, when programming Menu Displays, keypads 1

through 16 display on two separate displays. First, keypads 1 through 8 display. Press the COMMAND key

to display keypads 9 through 16. This same scheme is used for areas 1 through 32.

Note: Areas not pre-programmed at installation to display at this keypad cannot be viewed.

1.14 Asterisks in Programming

Asterisks display next to a programming option that is already selected. As shown in the example, options

that are selected to display the current programming selection have an asterisk next to the number. Those

that are not selected simply display the number. In the Devices example, keypads 3, 8, 9, and 15 are not

selected. In the Areas example, areas 3, 8, 9, 15, 19, 23, 25, and 31 are not selected. In both examples

the numbers with asterisks are selected.

Devices

Areas

*1 *2

*5 *6

*10 *11 *12

*1 *2

*5 *6

*4 *17 *18

19 *20

23 *24

*13 *14 15 *16

*21 *22

25 *26 *27 *28

*29 *30 31 *32

9 *10 *11 *12

*13 *14 15 *16

To select or deselect a number, simply enter the number using the digit keys on the keypad. This same

scheme is used when viewing the panel armed status and other programming and operational functions.

Remember to press the COMMAND key to display the rest of the device or area numbers.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

iniTializaTion

Initialization

NOTE: WHEN ANY PANEL PROGRAMMING IS CHANGED, THE STOP ROUTINE MUST BE RUN AND ‘SAVING

PROGRAM’ MUST DISPLAY ON THE KEYPAD IN ORDER TO SAVE THE PROGRAMMING CHANGES. SEE SECTION 17.1.

INITIALIZATION

2.1

Initialization

This function allows you to clear selected parts of the panel program back to the

factory defaults in preparation for system programming. Run the initialization

function on all new installations.

For each section of the panel program you

can initialize, a NO or YES option is provided.

CODES?

NO YES

Selecting YES advances you to

a confirmation prompt.

SURE?

YES NO

Selecting NO advances

you to the next prompt.

If you select YES, the panel initializes that section of

the program and advances you to the next prompt.

If you select NO, the panel advances you to the next

section prompt but does not initialize that section of

the program.

SCHEDS?

NO YES

INIT ALL? NO YES

2.2

2.3

Clear All Memory

NO - Leaves existing programming intact then displays Clear All Codes.

SURE?

YES NO

YES - Clears all memory then displays Reset Panel. Reset the panel by shorting J16

and re-enter programming mode to continue.

CODES?

SURE?

NO YES

YES NO

Clear All Codes

NO - Leaves existing codes intact.

YES - Clears the user code and user proﬁle memory and assigns user code number 99

to the highest user position.

Note: The user name for the default user code is created using the current

programmed primary user language.

SCHEDS?

SURE?

NO YES

YES NO

2.4

2.5

2.6

Clear All Schedules

NO - Leaves existing schedules intact.

YES - Clears all shift, and output schedules.

EVENTS?

SURE?

NO YES

YES NO

Clear Display Events Memory

NO - Leaves existing event memory intact.

YES - Clears the events memory.

ZONES?

SURE?

NO YES

YES NO

Clear Zone Information

NO - Leaves existing zone information intact.

YES - Clears the zone information for all zones. All zones are marked * UNUSED *

and must be renamed before being able to display on any system keypad.

AREAS?

SURE?

NO YES

YES NO

2.7

2.8

Clear Area Information

NO - Leaves existing area information intact.

YES - Clears the area information for all areas. All areas are marked * UNUSED * and

must be renamed before being able to display on any system keypad.

OUTPUTS? NO YES

SURE?

Clear Output Information

NO - Leaves existing output information intact.

YES NO

YES - Clears all programmed Output names and any output cutoff assignment.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

iniTializaTion

COM/RMT? NO YES

2.9

Clear Communication and Remote Options

NO - Leaves existing communication and remote options intact.

YES NO

SURE?

YES - Clears communication and remote options programming to factory defaults.

DEFAULTS NO YES

2.10

Set to Factory Defaults

NO - Leaves existing panel programming intact.

YES NO

SURE?

YES - Sets the remainder of the panel programming back to the factory defaults.

Note: Sets the Programming and User language to English.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

CommuniCaTion

Communication

Conﬁgure the communication options for the panel. The information you program

3.1

3.2

COMMUNICATION

varies with the Communication Type you select.

Account Number

The Account Number is a 1 to 5 digit number used to identify which panel is sending

a message. Enter the account number sent to the SCS-1R Receiver. Messages may

be sent to a central station or via PC Log Reports to a PC. The default is 12345.

ACCOUNT NO: 12345

NET, CELL, 232 and DD - The range of valid account numbers for a panel is 1 to

65535. For accounts of four digits or less, do not enter leading zeros.

CID - Choose an account number between 1 and 9999.

3.3

Transmit Delay

XMIT DELAY:

Enter the number of seconds (15 to 45) the panel waits before sending burglary

zones (Night, Day, or Exit) reports to the receiver. Other zone type reports are

sent immediately. Alarm bells and relay outputs are not delayed during this

period. Program Burglary Outputs for pulsed or steady, and set Abort Reports to

YES if Opening and Closing reports are not being sent. Enter 0 (zero) to disable this

function. The default is 30.

If the area where the alarm occurred is disarmed during the Transmit Delay time,

only an Abort Report (S45) message is sent to the receiver. If the area where

the alarm occurred is disarmed after the alarm message is sent to the receiver

but before the Bell Cutoff time expires even if the alarm was silenced, an Alarm

Cancelled (S49) message is sent. Otherwise the alarm is sent at the end of the

delay. The Alarm Cancelled report cannot be disabled.

Note: For Commercial Burglary Installations, the combined Transmit Delay

(Abort Window) and Entry Delay must not exceed one (1) minute.

3.4

3.5

Communication Path

PATH: -

Up to eight communication paths may be programmed. Each path is designated as

a primary or backup communication route. Path 1 is always Primary but other paths

may be programmed as additional primary or backup.

Each primary path establishes a new path group. A path group is made up of the

primary path and its subsequent backup paths. Typical communication takes place

on the primary path with backup paths being used only when the primary path fails

or when the backup path is programmed to duplicate messages. There is no option

to backup path 8.

Communication Type

Speciﬁes the communication method the panel uses on this path to report system

events to DMP SCS-1R Receivers or non-DMP receivers. Default is DD for Path 1, and

NONE for Path 2-8.

COMM TYPE:

NONE DD NET CID

NONE - For local systems. Selecting NONE ends communication programming.

DD - Digital Dialer communications to a DMP SCS-1R Receiver.

NET - Network communication using the panel onboard network connection. The

DMP Network/Output reporting format is transmitted over a data network to the

SCS-1R Receiver.

CID - This option allows the panel to communicate to non-DMP receivers using the

Contact ID format.

CELL - This option allows communication over the GPRS network using digital

cellular technology with the 463G or CellCom Series Digital Cellular Communicator.

CELL 232

232 - This option sends serial data and can be used for radio backup or other

communication options, and uses the on-board serial port.

Select 232 when using a 462N Interface Card or DB-9 backup communications by

directly connecting to the RS-232 port on the panel. If using the on-board RS-232

port, set the XR500 Series Canadian panel J23 jumper to R and brieﬂy reset the

panel using the J16 jumper to activate RS-232 operation. Refer to the XR500 Series

Canadian Installation Guide (LT-0681CAN).

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

CommuniCaTion

3.6

3.7

Path Type

PATH TYPE: BACKUP

The Path Type deﬁnes if the path is Primary or Backup. Because Path 1 is Primary,

this prompt only displays for paths 2-8. Default is Backup.

PRIMARY

BACKUP

Note: If the Primary Communication Type is CELL, then the backup Communication

Type can only be NET or 232.

Test Report

TEST RPT: YES

Test Report determines if test reports are sent on this path. Reports are sent

according to the programming in Test Frequency and Test Time. Default is Yes.

Select YES to allow the programmed test report to be sent on the path currently

being programmed.

NO YES DEFER

Select DEFER to not send a test report if the panel communicates any message to the

receiver within the time set in Test Frequency. Select NO to not send test reports on

this path.

3.8

3.9

TEST FREq: 1 DY Test Frequency

Test Frequency determines the frequency of the test report. Enter a number from

1 to 60 and select DY (Day) or HR (Hour) by pressing the far right top row select key.

Default is 1 Day.

Test Day

TEST DAY: SUN

Use this option to set the day of the Test Report. This prompt appears only when Test

Report is Yes, Test Frequency is Day and a multiple of seven. Press the COMMAND key

to display the ﬁrst four days of the week. Press the COMMAND key to display the last

three days. Select the day of the week to send the test report. Default is Sunday.

3.10

3.11

Test Time

TEST TIME:

0:00 AM

Use this option to select the time of day for Test Reports. Select the hour, minute

and AM/PM. Enter 0:00 AM to disable this feature. Default is 0:00 AM.

Check In

NO YES

CHECKIN:

This option displays if the COMM TYPE is NET, 232 or CELL. Check-in reports are a

method of supervising the panel for communication with the receiver. For NET the

default is YES. For CELL or 232 the default is NO.

Select RND (Random) for the panel to check-in at random times from 6 to 60 minutes

CHECKIN:

NO YES RND ADPT when all areas are disarmed. If any area is armed a check-in is sent every 6 minutes.

Select ADPT (Adaptive) for a backup path to adapt to the check-in programming

from this groups primary path if the primary path becomes unavailable. Check-in

programming includes Check-in and Fail Time.

Select ADP3 (Adaptive 3) for a backup path to adapt using a 3 minute Check-in and

Fail Time if the primary path becomes unavailable. This option also indicates a

Communication Trouble (S10) if the cell tower is unavailable for 3 minutes.

When YES is selected, enter the number of minutes between check-in reports, from

2 to 240 for NET and 232 or 3 to 240 for CELL, when the panel is armed or disarmed.

For CELL or 232 the default is 0. For NET the default is 200.

CHECKIN:

ADP3

CHECKIN MINS: 200

FAIL TIME:

240

3.12

Fail Time

This option displays if CHECKIN is set to YES. Entering a FAIL TIME allows the

receiver to miss multiple check-ins before logging that the panel is missing. The

maximum fail time is 240 minutes. For example, if CHECKIN is 10 and FAIL TIME is

30, the receiver only indicates a Panel Not Responding after 30 minutes. The FAIL

TIME must be equal to or greater than the CHECKIN time. Default is 0 for CELL and

232. Default is 240 for NET.

3.13

3.14

Encryption (XR500E only)

ENCRYPT NO YES

Select Yes to enable encryption for the path currently being programmed. Default is NO.

Receiver IP

RECEIVER IP

This option displays only if the Communication Type is NET or CELL. Enter the

Receiver IP address where the panel sends network messages. The Receiver IP

Address must be unique and cannot be duplicated on the network. Enter all 12

digits and leave out the periods. For example, enter IP address 192.168.0.250 as

192168000250. The periods display automatically.

000.000.000.000

XR500 Series Canadian Programming Guide

Digital Monitoring Products

Download from Www.Somanuals.com. All Manuals Search And Download.

CommuniCaTion

3.15

Receiver Port

RECEIVER PORT -

2001

Enter the receiver port number. Valid range is 1 to 65,535. Default is 2001.

3.16

First Telephone Number

This option displays only if the Communication Type is DD or CID.

FIRST PHONE NO.

This is the ﬁrst number the panel dials when sending reports to the receiver. Phone

numbers can have two lines of 16 characters each to equal up to 32 characters.

Enter P to program a three-second pause in the dialing sequence. The P character

counts as part of the 32 allowable characters.

Enter R as the ﬁrst character for rotary (pulse) phone function. The R character

counts as part of the 32 allowable characters.

Call Waiting: You can place the “* 7 0 P” (Star, Seven, Zero, Pause) in the telephone

number ﬁrst position to cancel Call Waiting. For example, program NET with second

line DD and phone number *70P555-1212, and you have NET with Call Waiting

cancelled on the second line.

Caution: A call waiting cancel programmed on a non-call waiting telephone line

would prevent communication to the central station.

3.17

Second Telephone Number

SECOND PHONE NO.

The panel dials the second number when two successive tries using the ﬁrst number

fail. If the panel cannot reach the receiver after two attempts using the second

number, it returns to the ﬁrst number and makes two additional attempts. A total of

ten dialing attempts are made using the ﬁrst and second phone numbers.

Each number can be up to 32 characters in length including any P or R characters

entered for pause or rotary connections or call waiting cancel option.

Should all ten attempts fail, the panel continues to attempt sending the message

using the next programmed path. If all programmed communication paths fail, the

panel clears the communication buffer and makes one communication attempt each

hour to send a TRANSMIT FAILED (S87) report to the receiver. Access the User Menu

Display Events feature to view the report information not sent to the receiver or

download the report with DMP Remote Link™ software.

3.18

3.19

Advanced Programming

ADVANCED? NO YES

Select Yes to enter the Advanced Programming menu for the communication path

currently being programmed.

First GPRS APN

FIRST GPRS APN

SECURECOM400

Enter the ﬁrst APN (Access Point Name). This allows an access point for cellular

communication and is used to connect to a DNS network. The APN may contain two

lines of 16 characters to equal 32 characters. Default is set to SECURECOM400.

Second GPRS APN

SECOND GPRS APN

Enter the second APN (Access Point Name). This works as a backup in case the ﬁrst

APN fails. The APN may contain two lines of 16 characters to equal 32 character

Default is set to SECURECOM400.

SECURECOM400

3.20

3.21

FAIL TEST HRS:

Fail Test Hours

This option sets the frequency for a Backup or Adaptive path to send a test report

when the closest previous path fails within its path group.

For example, if a backup path is programmed to send a weekly test report and the

Fail Test Frequency is set to 2 hours, when the previous path fails within its group,

the backup path starts sending a test every 2 hours until the previous path restores.

If Fail Test Frequency is set to 0, test reports are sent only according to Test Report

programming. Range is 0 to 24 hours. Default is 0.

PROTOCOL: TCP

Protocol

This option displays only when Communication Type is NET.

Select TCP to communicate over the network using TCP protocol. Select UDP to

communicate using UDP protocol. Default is TCP.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

CommuniCaTion

RETRY SECONDS: 6

3.22

Retry Seconds

This option displays for NET or 232 Communication Types.

Enter the number of seconds (between 6 and 15) the panel should wait before

retrying to send a message to the receiver if an acknowledgment was not received.

The panel retries as many times as possible for a period of one minute before

sending a network trouble message. For example, if retry time is set to 15, the

panel retries four times. The default Retry Time is 6 seconds.

Note: If TCP is enabled, the minimum Retry Time programmed is 6 seconds.

3.23

3.24

Substitution Code

SUB CODE

This option displays when the Communication Type is NET, CELL or 232. The Panel

Substitution Code increases the level of security by helping to ensure that the panel

sending the message to the receiver has not been substituted by another panel. The

default is NO.

NO YES SHARED

Select YES to send a substitution code with every message.

Select SHARED (SHR) to use the same substitution code as operating in the previous

path.

232 Communication Port

This option displays when Communication Type is 232.

232 COMM PORT:

This option sets the physical RS-232 port to the on-board connector or one of the DMP

Model 461 Interface Adaptor Card slots labeled A, B, C, D, or E. Use slot A if using a

462N Network Interface Card with or without the 461 card.

Enter O to use the on-board connector. Set the XR500 Series Canadian panel J23

jumper to R and brieﬂy reset the panel using the J16 jumper to activate RS-232

operation. Default is O (On-board).

3.25

3.26

232 Setup String

232 SETUP:

This option displays when the Communication Type is 232. Enter up to two lines of 16

characters to equal up to 32 characters for the destination address that may include

an IP address. Example: If using a DMP iCOM, enter AT#UCXXX.XXX.XXX.XXX#PPPPP

where X is the IP address and P is the port number.

893A

NO YES

893A:

This option displays when the Communication Type is DD or CID.

The 893A option allows reports to be sent to the receiver on a second DD line using

the 893A module. Default is No.

When using this option, Test Report messages (S07 Automatic Recall Test or

S88 Unrestored System Recall Test) are sent to the receiver at the frequency

programmed in Test Frequency, alternating between the ﬁrst and second phone line.

For example, a DD path with an 893A module set for daily test report frequency

sends a test report through phone line 1 one day and phone line 2 the next day.

If 893A option is set to YES, enter up to a 3 digit preﬁx to be dialed before the

second phone number. If no preﬁx is entered, the second phone number is dialed as

originally entered.

2ND LINE PREFIX:

3.27

3.28

Alarm Switch

ALARM SWITCH:

This prompt displays for DD or CID Communication Types.

Enter the number of attempts to send an alarm message before switching to the next

path. Range is from 1 to 10. All non-alarm messages are sent for 10 attempts on the

dialer before a switch is initiated. If the path immediately following this channel is

not a backup path, this option has no effect. Default is 1.

NO YES

DUPLICATE ALARMS

Duplicate Alarms

This prompt displays for BACKUP paths. If Yes is selected, the current backup path

duplicates all alarms occurring on its group primary path. Default is No.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

CommuniCaTion

3.29

Alarm Reports

ALARM

YES

This prompt displays when the Path Type is Primary. All backup paths within the

group follow the same programming for Alarm Reports. Default is Yes.

When YES is selected, the following reports are sent to the receiver for all zone

types:

NO YES FIRE

• Alarm

• Bypass

• Reset

• Restore

When FIRE is selected, the following reports are sent for Fire, Fire Verify and

Supervisory Zones:

• Alarm

• Bypass

• Reset

• Restore

3.30

SPV/TRBL YES

NO YES FIRE

Supervisory/Trouble Reports

This prompt displays when the Path Type is Primary. All backup paths within the

group follow the same programming for Supervisory/Trouble Reports. Default is Yes.

When YES is selected, the following reports are sent for all zone types:

• Trouble

• Low Battery

• Missing

• Fault

• Restorals

• System Troubles

• System Restoral

When FIRE is selected, the following reports are sent for Fire, Fire Verify, and

Supervisory Zones:

• Trouble

• Low Battery

• Missing

• Fault

• Restorals

• System Troubles

• System Restoral

3.31

3.32

Opening/Closing and User Reports

O/C USER NO YES

This prompt displays when the Path Type is Primary. All backup paths within the

group follow the same programming for Opening/Closing and User Reports. Default

is Yes.

When YES is selected, the following reports by user are sent to this receiver.

• Opening

• Closing

• Bypass

• Reset

• Code changes (including adding, deleting, changing)

• Schedule changes (temporary, permanent, shift)

• Holiday date changes

Door Access Report

YES

DOOR ACS

This prompt displays when the Path Type is Primary. All backup paths within the

group follow the same programming for Door Access Reports. Default is Deny.

Select YES to enable Door Access Granted and Denied reports to this receiver

whenever a door access is granted to a user. The Door Access Granted report is

only sent if the keypad number has also been selected in Access Keypads under the

SYSTEM REPORTS programming.

NO YES DENY

Note: To minimize cellular data, Door Access Granted reports are not sent on a CELL

path type.

Select DENY to enable Door Access Denied reports only to this receiver when a door

access is denied to a user.

SEND COMM TRBL:

NO YES

3.33

3.34

Send Communication Trouble

This prompt displays for each path and determines if and how communication

trouble on the path is sent to the receiver. A trouble message indicates both the

path number and communication type that failed. Default is Yes.

SEND PATH INFO:

NO YES

Send Path Information

This prompt displays for each path and if YES, each panel message includes path

information such as path number, communication type, and path type. Default is No.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

neTwork oPTionS

Network Options (XR500N/XR500E only)

Network Options are provided to deﬁne the network conﬁguration for the panel. This information will be

used during communication of messages via network or email.

Note: IP addresses and port numbers may need to be assigned by the network administrator. When

entering an IP, Gateway, or Subnet Mask address be sure to enter all 12 digits and leave out the periods.

For example, IP address 192.168.000.250 is entered as 192168000250.

DHCP

NO YES

4.1

DHCP Mode Enabled

If the panel uses a dynamic IP address select YES. When set to YES, the panel

operates using DHCP and does not use the Local IP Address number. When the DHCP

option is set to NO, the panel uses the IP address entered in Local IP Address. The

default value for DHCP mode is YES.

LOCAL IP ADDRESS

4.2

4.3

4.4

Local IP Address

Enter the local IP address. The Local IP Address must be unique and cannot be

duplicated. The default local IP address is 192.168.0.250.

192.168.0.250

GATEWAY ADDRESS

Gateway Address

192.168.0.1 Enter the local gateway address. The Gateway IP Address is needed to exit your

local network. The default gateway address is 192.168.0.1.

SUBNET MASK

255.255.255.000

Subnet Mask

Enter the local subnet mask assigned to the panel. The default subnet mask address

is 255.255.255.000.

DNS SERVER

192.168.0.1

4.5

4.6

DNS Server

Enter the IP address of the DNS (Domain Name System) used by the panel to resolve

domain names into IP addresses. The default address is 192.168.0.1.

PASSPHRASE

Passphrase (XR500E only)

To enable encryption type an 8 to 16-character Passphrase using alphanumeric

characters. If you leave the Passphrase blank, the panel communicates with the

SCS-1R Receiver, but the data is not encrypted. The Passphrase is blank by default.

The XR500E panel is capable of communicating encrypted data to an SCS-101

Network Line Card installed at the receiver. The XR500E panel and the SCS-101 must

have the same secret password called a Passphrase.

Note: DO NOT LOSE THE PASSPHRASE. A lost or forgotten Passphrase requires that

the XR500E panel and every iCOM-E unit reporting in to the same iCOM-E unit at the

receiver be individually reprogrammed with a new passphrase.

Note: An XR500E panel communicates using AES encryption. If you currently have

an XR500N panel installed, you may purchase a separate feature key to activate

encrypted communications using the Feature Upgrade process described in the

Feature Upgrade Section. Encrypted communication cannot be enabled on a

standard XR500 panel.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

meSSaging SeTuP

Messaging Setup

MESSAGING SETUP

5.1

Messaging Setup

This section allows you to enter the information needed to receive messages

directly from the panel via email and In Touch™ SMS Text using Network or Cellular

communication. All of the name and password options below allow up to 32

lowercase characters to be entered. The Destination addresses allow up to 48

characters to be entered. System Name is displayed with initial caps.

The transmitted messages are:

• Zone Alarms by Zone Name

• Zone Troubles by Zone Name

• Zone Bypass by User

• Arming (Closings) by User

• Disarming (Openings) by User

• Late to Close

• AC Power Trouble and Restoral

• System Low Battery

• Ambush

• Abort, Cancel and Alarm Veriﬁed by User

• Check-in by user

5.2

5.3

Enable Messaging

Select YES to allow the panel to send messages to three programmed destinations.

Default is NO.

ENABLE MESSAGING

NO YES

System Name

SYSTEM NAME

Enter a unique name for the panel. The panel name is used as the sender of the

message. The text entered is displayed with initial caps. If this ﬁeld is left blank, the

panel account number is sent.

DESTINATION 1

5.4

Destination 1

Enter the ﬁrst email address or cell phone number where messages will be sent. The

message can be sent to any device (computer, cell phone, PDA) as long as a valid

email address or cell phone number is entered. When entering email addresses,

press the 7 digit key followed by the fourth Select Key to add the @ symbol and the

9 digit key followed by the fourth Select Key to add the _ symbol. See the Entering

Non-Alpha Characters section for additional symbols.

Note: Mail servers that require Transport Layer Security (TLS) encryption are not

supported by the XR500 Series.

5.5

Destination 1 User Number

DESTINATION 1

USER NUMBER:

If Destination 1 is a 10-digit cellular number, enter a user’s user number from this

account. This option is used when sending commands such as arming or disarming

back to the panel using In Touch™ SMS Text from the same cell phone or PDA. The

user number must have the authority to perform the commands as if it occurred at the

keypad. In Touch™ SMS Text command operation is available in XR500 Series panels

using version 205 or higher. Entering 0 (zero) disables this option. Default is 0.

DESTINATION 2

5.6

5.7

Destination 2

Enter the second destination email address or cell phone number.

Destination 2 User Number

If Destination 2 is a cellular number, enter the user’s User Number for

arming/disarming authorization.

DESTINATION 2

USER NUMBER:

DESTINATION 3

5.8

Destination 3

Enter the third destination email address or cell phone number.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

meSSaging SeTuP

5.9

Destination 3 User Number

If Destination 3 is a cellular number, enter the user’s User Number for

DESTINATION 3

USER NUMBER:

arming/disarming authorization.

5.10

EMAIL COMM TYPE

NET CELL

Email Communication Type

Choosing NET sends email messages over the network. Choosing CELL sends email

messages via cellular communication. Default is NET. This prompt appears only if

any destination above is an e-mail address and the panel is a network panel (has an

Ethernet connector).

O/C EMAIL NO YES

5.11

5.12

O/C Email

Select YES to allow the panel to send Opening and Closing reports via email. Default

is NO. This prompt displays if any destination above is an email address.

O/C SMS

NO YES

O/C SMS

Select YES to allow the panel to send Opening and Closing messages to a cell phone

via SMS protocol. Default is NO. This option displays if any destination above is a

cell phone number.

MONTHLY LIMIT:

5.13

Monthly Limit

This option displays if any programmed destination is a cell phone number using

NET or CELL communication or an email address using CELL communication. If

all destinations are email addresses using NET communication, this option does

not display. This number limits the monthly incoming and outgoing SMS messages

allowed to be sent or received by the panel.

A panel event that causes messages to be sent to destination cell phone numbers

or destination email addresses is counted towards the panel’s monthly limit. For

example, if an alarm message is sent to a cell phone number and an email address

using CELL communication, a total of 2 messages are counted towards the monthly

limit for the panel. SMS messages sent from a cell phone to the panel, including

status requests and In Touch™ SMS Text messaging commands, also count toward the

monthly limit. The limit is reset at midnight on the 14th of every month. Range is

from 0 to 999. When 0 is entered, there is no limit on the number of messages able

to be sent or received by the panel. Default is 0.

Note: The SecureCom Wireless text plan selected for the panel should match or

exceed the programmed Monthly Limit.

The remaining options only appear if email messaging has been selected to be sent via network. The options allow

the email server to be selected by the installing dealer. Typically this is the email service provided by the installing

dealer. This allows opportunity for additional services to be provided to the end user.

SMTP SERVER

5.14

SMTP Server

Enter the SMTP (Simple Mail Transfer Protocol) Server name. The SMTP email server

is responsible for sending the email to its destination. An example SMTP email

server name is: mail.somedomain.com. The domain should be the email server that

provides email support for your alarm customers.

SMTP PORT:

5.15

5.16

SMTP Server Port

The SMTP server port number is the port that the panel uses to initiate a TCP

connection with the email server. The default port is 25.

SMTP USERNAME

SMTP Username

Most SMTP servers require a username to send email. This is sent to the SMTP server

in conjunction with the SMTP Password to provide email authentication to the server.

SMTP PASSWORD

5.17

5.18

SMTP Password

Most SMTP servers require a password to send email. This is sent to the SMTP server

in conjunction with the SMTP Username to provide email authentication to the server.

Passwords display as lowercase.

FROM EMAIL

From Email Address

Enter the email address on ﬁle with the email service. This displays in the email

message as the sender’s address.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

deviCe SeTuP

Device Setup

DEVICE SETUP

6.1

This section allows you to deﬁne the XR500 Series Canadian panel physical

conﬁguration. You can install and address up to sixteen supervised devices on the

keypad data bus.

DEVICE NO:-

6.2

Device Number

DEVICE 1: DOOR

Enter the device number on the keypad bus you are programming. The keypad bus

can have up to 16 devices.

Note: After you program each option for the ﬁrst device, repeat these programming

steps for each additional devices.

DOOR - (XR500 Version 205) The device is an access control device and is either a

keypad or a Wiegand Interface Module.

DOOR KPD FI NONE

KEYPAD - (XR500 Version 205) The device is either a keypad or a zone expander

device.

FIRE - The device is a Remote Fire Command Center.

NONE - No device is set for this address.

6.3

6.4

Door Name

DOOR NAME 1

ACCESS AREAS:

The door name displays. To change the name, press any top row Select key then

enter up to 16 characters for the door name. Press COMMAND to continue device

setup programming.

Access Areas

Press the COMMAND key to program Access Areas. To select an area, enter the area

number using the digit keys on the keypad. When an area is selected, an asterisk

appears next to the area number. Enter the number again to deselect the area.

Press COMMAND to display the next set of areas. Refer to the Multiple Displays

section at the beginning of this document.

Users must have matching access area numbers assigned to their code to receive a

door access at this device.

If you do not enter any area numbers, all users with Door Access authority receives a

door access without regard to schedules. If the user code is programmed for Anti-Pass

YES, then the user is logged into all matching areas. This user is not allowed to access

these areas again until they have egressed the area. See Egress Areas.

When all areas accessed by a door are armed, the door is locked by the panel.

Note: For an All/Perimeter, Home/Sleep/Away, or Home/Sleep/Away with Guest

system, Access Areas should be left at factory default settings.

6.5

EGRESS AREAS:

Egress Areas

Press the COMMAND key to program Egress Areas. To select an area, enter the area

number using the digit keys on the keypad. When an area is selected, an asterisk

appears next to the area number. Enter the number again to deselect the area.

Press COMMAND to display the next set of areas. Refer to the Multiple Displays

section at the beginning of this document.

Note: For an All/Perimeter, Home/Sleep/Away, or Home/Sleep/Away with Guest

system, Egress Areas should be left at factory default settings.

Note: If an area is programmed as an access area, it cannot be programmed as an

egress area and therefore does not display during Egress Areas programming.

Use this option to detect Anti-passback violations. Anti-passback requires a user to

properly exit (egress) an area they have previously accessed. If users fail to exit

through the proper card reader location they are not granted access on their next

attempt. Users must have matching access area numbers assigned to their proﬁle,

to receive a door access at this device. If the user is programmed for Anti-Pass

YES, then the user is logged out of all matching areas. This allows the user to again

access the area. See Access Areas section.

If you do not enter any area numbers, all users with Door Access authority receives a

door access without regard to schedules. If you are not using the Anti-Pass feature

leave Egress Areas blank.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

deviCe SeTuP

DISPLAY AREAS:

6.6

Display Areas

Press the COMMAND key to program Display Areas. To select an area between 1 and

32, enter the area number using the keypad digit keys. When an area is selected, an

asterisk appears next to the area number. Enter the number again to deselect the

area. Press COMMAND to display the next set of areas. Default is all area numbers.

Refer to the Multiple Displays section at the beginning of this document.

*1 *2 *3 *4

*5 *6 *7 *8

*9 *10 *11 *12

*13 *14 *15 *16

Display Areas allows the XR500 Series burglary activities to be segmented so that

only speciﬁc area(s) and their associated operation appear at a particular keypad.

Area number(s) selected in this ﬁeld affect the way users interact with the system

from this particular device. For example: Program Device 1 to show only the zone

activities and armed status of Area 1.

*17 *18 *19 *20

*21 *22 *23 *24

*25 *26 *27 *28

*29 *30 *31 *32

Enter the area number(s) that this keypad is to display. This allows speciﬁc area control

from speciﬁc keypads, as well as annunciation of zones assigned to those area(s). When

Display Areas is left defaulted (all areas selected), Menu Display and Status List items

determine whether zone alarms and troubles display at this device, regardless of area

assignment. Also, all system areas may be armed and disarmed from this device.

Note: For an All/Perimeter or Home/Sleep/Away system, Display Areas should be

left at factory default settings.

For Home/Sleep/Away with Guest arming systems, the Display Areas selection

determines which system the keypad arms and disarms. With areas 1, 2 or 3 being

the ﬁrst areas selected, the keypad is assigned to the Main system. With area 4, 5 or 6

being the ﬁrst areas selected, the keypad is assigned to the Guest 1 system. With area

7, 8 or 9 being the ﬁrst areas selected, the keypad is assigned to the Guest 2 system.

Keypads can have additional areas assigned for Event Display.

User Action Allowed

When an area(s) is selected, the following user actions are allowed:

• Arming or Disarming of the area(s) selected from the ARM or DISARM menu

• Alarm Silence for the area(s) selected

• Zone Bypass of zones assigned to the area(s) selected

• Zone Monitor of zone assigned to the area(s) selected

• Shift schedule changes allowed for the area(s) selected

• Closing Check Schedule Extend is allowed for the area(s) selected

• Door Schedules changes are allowed for devices that have a matching area(s)

as deﬁned in Device Access Areas

• Door On/Off Menu operation is allowed for devices that have a matching area(s)

as deﬁned in Device Access Areas

Note: The previous user actions also require the matching area(s) be programmed in

User Proﬁle: Arm/Disarm area(s).

Status Display Allowed

When an area(s) is chosen, the following displays are allowed:

• Armed Status of the selected area(s)

• Zone Alarms and troubles for burglary (NT, DY, EX, A1, A2) type zones assigned to

the selected area(s)

• Late to Close status of the selected area(s)

• Zone Status (normal/fault) of zones that are assigned to the selected area(s)

Options and Actions Not Affected

The following options are not affected by the Display Areas operation. The User

Code authority level controls access to these items.

• Sensor Reset Menu

• Outputs On/Off Menu

• System Status Menu

• Forgive Anti-Passback

• System Test/Panic Test • User Proﬁles

• Service Request

• Fire Drill

• Set System Time and Date

• Display Events

• 24-hour zones display at keypads based on Status List programming only

Note: A common area and its operations cannot be assigned to a speciﬁc keypad.

Display Areas example: When Device 1 has Display Areas set to 20, 21, and 22, it

annunciates troubles and alarms only for zones assigned to those areas.

When arming/disarming from Device 1, only areas 20, 21, and 22 may be armed/

disarmed, even when the User Proﬁle has authority to arm/disarm other system areas.

Exception: Disarming of other areas not selected in Display Areas can be

accomplished by presenting a card that has disarming authority and matching proﬁle

areas with areas assigned in Device Access Areas.

XR500 Series Canadian Programming Guide

Digital Monitoring Products

Download from Www.Somanuals.com. All Manuals Search And Download.

deviCe SeTuP

STRIKE TIME:

6.7

Strike Time

This option displays if DOOR is selected as Device Type.

Enter a door access time, between 1 and 250 seconds, during which a keypad or access

control device relay is activated. Magnetic locks or electric door strikes are connected

to the relay and released for the length of the strike time. Default is 5 seconds.

Enter 0 (zero) to activate the device relay with a toggle action. This allows the user

to activate or deactivate the device relay each time a valid user code is entered.

The device relay is activated or deactivated until a user code is entered again.

Note: The Request to Exit door access time of a keypad or Model 733 Wiegand

Interface Module is not affected by this selection. It remains at 5 seconds.

Strike Delay

STRIKE DELAY:

6.8

6.9

This option displays if DOOR is selected as Device Type.

Enter the number of minutes, 0 to 9, to delay a door strike after a valid code is entered

or a card read occurs. When a valid code or card read or code is received, the activation

of the door strike is delayed for the number of minutes programmed. The standard door

strike message is sent to the Central Station receiver and logged in the Display Events at

the time of card read or code entry and is not delayed. During this delay, all subsequent

codes entered or cards presented to the reader for a door strike are ignored and no

record of the attempt is stored. Enter 0 (zero) to disable. Default is 0 (zero).

Fire Exit Release

FIRE EXIT NO YES

Select YES to allow the door access relay at this address to be released whenever

Fire panic keys are pressed or a Fire or Fire Verify zone alarm is in the Status List.

The relay is reset whenever a Sensor Reset is performed to remove all Fire and Fire

Verify zone alarms from the Status List. Select NO to not allow the door access relay

at this address to be released.

OUT GROUP NO YES

OVERRIDE NO YES

6.10

6.11

Output Group

Select YES to allow the output group (relays) assigned to the user proﬁle to turn ON

when the device relay is activated for the programmed strike time. This could be

used to operate an elevator control. Default is NO. See the User Proﬁles section in

the Appendix of this document for more information about proﬁles.

Schedule Override

Use this option to allow door ON/OFF schedules to be overridden by the armed

condition of the system. Selecting YES causes the on time for a door schedule to be

ignored when all areas assigned to Access Areas for this device are armed. Should

any area become disarmed after the door schedule on time, the device output turns

on. A door output which is on during a disarmed period automatically turns off when

all access areas assigned to the device become armed, even if the scheduled off

time has not been reached. This feature can be used to keep doors locked when a

factory opens late, or is forced to close early, due to a snow storm or other cause.

Select NO to allow door schedules to operate independent of system armed status.

Note: When OVERRIDE is YES and there are no areas programmed in ACCESS AREAS,

the door schedule for that device does not work. Either set OVERRIDE to NO or

enter an area number in ACCESS AREAS.

AUTO FORCE ARM

6.12

Auto Force Arm Device?

Select YES to have all Display Areas assigned to this keypad automatically arm and

force arm faulted zones at arming. The user is not prompted to select areas to

arm or force arm faulted zones after choosing ARM at the keypad. If Closing Code

is programmed as YES, only the matching areas between the Display Areas and

the User Code’s authorized areas arm. Also, when YES is selected, the user is not

prompted to select areas to disarm after entering a code at Entry Delay or after

choosing Disarm at the keypad. All matching areas assigned to the User Code and to

this keypad are automatically disarmed. When NO is selected, the user is prompted

to select areas (ALL NO YES) and choose to force arm or bypass at arming and

disarming. Default is NO.

DEVICE?

NO YES

DOOR REAL-TIME

6.13

6.14

Door Real-Time Status?

Select YES to have real-time door status messages sent to PC Log reporting and Entré

reporting for this device. Messages are sent anytime the panel turns the door relay on or

off. Default is NO.

STATUS?

NO YES

SEND DOOR FORCED

Send Door Forced Message?

Select YES to have the panel send a real-time door status message of Forced Open (FO)

to PC Log reporting and Entré reporting when the door relay is off, but the door zone has

transitioned from its normal state. Default is NO.

MESSAGE? NO YES

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

deviCe SeTuP

6.15

Program 734 Options

PROGRAM 734

Select YES to program the 734 Wiegand Interface Module. Device type must be set to

OPTIONS? NO YES

DOOR.

6.15.1

Activate Zone 2 Shunt

ACTIVATE ZONE 2

SHUNT?

Select YES to activate the Soft-Shunt™ option.

NO YES

Selecting NO allows standard zone operation on Zone 2 and displays the ACTIVATE

ZONE 3 REX option. Default setting is NO.

If the door being released by the 734 module is protected (contact installed), you

can provide a programmable Soft-Shunt entry/exit timer by connecting its contact

wiring to the 734 module Zone 2. When the on-board Form C relay activates and

the user opens the door connected to Zone 2, the zone is shunted for the number of

seconds programmed in ZONE 2 SOFTSHUNT TIME allowing the user to enter/exit.

If Zone 2 does not restore (door closed) within the programmed time minus ten

seconds, the piezo sounds every other second during the timer last ten seconds. If

Zone 2 restores prior to the end of the programmed time, the piezo silences. If the

zone does not restore after the ten second piezo time, the 734 ends the shunt and

indicates the open or short zone condition to the panel.

If you select YES, pressing the COMMAND key displays ZONE 2 SOFTSHUNT TIME. The

Back Arrow returns to the Program 734 Options.

6.15.2

Zone 2 Soft-Shunt Time

ZONE 2 SOFTSHUNT

Enter the number of Soft-Shunt seconds to elapse before the Soft-Shunt timer

expires. Range is from 20 to 250 seconds. Press any top row select key to enter the

number of seconds. If the door remains open when the timer expires a zone open/

short is sent to the panel for Zone 2. The default is 40 seconds.

Press the COMMAND key to move forward to RELOCK ON ZONE 2 FAULT. The Back

Arrow returns to the ACTIVATE ZONE 2 SHUNT option.

TIME:

6.15.3

6.15.4

Relock on Zone 2 Fault?

RELOCK ON ZONE 2

Selecting NO leaves the relay on when Zone 2 faults to an open or short condition

during Soft-Shunt. Selecting YES turns the relay off when Zone 2 faults open or short

during Soft-Shunt. The default is NO.

FAULT?

NO YES

Press the COMMAND key to display ACTIVATE ZONE 3 REX:. The Back Arrow returns to

the ZONE 2 SOFTSHUNT TIME: option.

Activate Zone 3 Request to Exit

ACTIVATE ZONE 3

REX?

Selecting YES activates the Zone 3 Request to Exit (REX) option.

NO YES

Selecting NO allows standard zone operation on Zone 3 and displays the ACTIVATE

ONBOARD SPEAKER option. Default setting is NO.

Optionally connect a PIR (or other motion sensing device) or a mechanical switch to

Zone 3 to provide REX capability to the system. When Zone 3 shorts, the on-board

Form C relay activates for the programmed number of seconds. During this time,

the user can open the protected door to start the programmed Soft-Shunt™ entry/

exit timer. After the programmed number of seconds, the relay restores the door to

its locked state.

The 734 module provides a shunt-only option for REX on Zone 3. When Zone 3 opens

from a normal state, only a Soft-Shunt occurs: the on-board relay does not activate.

This shunt-only option uses two methods of REX. The ﬁrst REX device provides the

programmed Soft-Shunt entry/exit timer. The second REX device, or manual device

such as a door knob, unlocks the door.

An example of the shunt-only conﬁguration is a door to an ofﬁce that is locked 24

hours a day. Users pass a REX motion detector positioned by the door to begin the

programmed exit timer. Within the programmed number of seconds the user must

then manually activate a second device, such as a REX device or manual door knob,

to unlock the door. If the door is opened after the programmed number of seconds,

the zone goes into alarm.

If you select YES, pressing the COMMAND key displays ZONE 3 REX STRIKE TIME. The

Back Arrow returns to the ACTIVATE ZONE 2 SHUNT option.

ZN 3 REX STRIKE

TIME:

6.15.5

Zone 3 REX Strike Time

Enter the number of REX seconds to elapse. Range is from 5 to 250 seconds. Press

any top row select key to enter the number of seconds. The default is 5 seconds.

Press the COMMAND key to move forward to the ACTIVATE ONBOARD SPEAKER option.

The Back Arrow returns to ACTIVATE ZONE 3 REX.

XR500 Series Canadian Programming Guide

Digital Monitoring Products

Download from Www.Somanuals.com. All Manuals Search And Download.

deviCe SeTuP

6.15.6

Activate Onboard Speaker

Select YES to enable the onboard piezo speaker for local annunciation. Select NO to

turn the piezo off for all operations. This does not affect remote annunciator open

collector (RA) operation. The default is YES.

ACTIVATE ONBOARD

SPEAKER? NO YES

Press the COMMAND key to display the CARD OPTIONS option. The Back Arrow

returns to ACTIVATE ZONE 3 REX.

CARD OPTIONS:

6.15.7

Card Options

DMP

Press any top row Select key to display options. Press the select key under DMP or

CUSTOM to select that option. Select DMP to indicate the reader sends a 26-bit DMP

data string. Press the COMMAND key to display REQUIRE SITE CODE.

DMP

CUSTOM

Note: When set to DMP, the 734 converts 17 bits of the 26-bit data string into a

5-digit number.

Select CUSTOM if using a non-DMP card or user code length of 6 to 10 digits.

Default is DMP.

6.15.8

Custom Card Deﬁnitions

26 When using a custom product, enter the total number of bits to be received in

Wiegand code including parity bits.

WIEGAND CODE

LENGTH:

Press any top row Select key to enter a number between 0-255 to equal the number

of bits. Default is 26 bits.

Typically, an access card contains data bits for a site code, a user code, and start/

stop/parity bits. The starting position location and code length must be determined

and programmed into the 734 Module.

0 1 1 1 0 1 0 1 1 0 1 1 0 1 0 1 0 0 0 1 1 0 0 1 1 1

Site Code

Position = 1

Length = 8

User Code

Position = 9

Length = 16

Last Bit

Received

Position = 25

First Bit

Received

Position = 0

In this example the Wiegand Code Length = 26 bits.

SITE CODE

POSITION:

6.15.8.1

6.15.8.2

Site Code Position

Enter the site code start position in the data string. Press any top row Select

key to enter a number between 0-255. Default is 1.

SITE CODE

LENGTH:

Site Code Length

Enter the number of characters the site code contains. Press any top row

Select key to enter a number between 1-16. Default is 8.

USER CODE

POSITION:

6.15.8.3

6.15.8.4

User Code Position

Deﬁne the User Code start bit position. Press any top row Select key to

enter a number between 0-255. Default is 9.

USER CODE

LENGTH:

User Code Length

Deﬁne the number of User Code bits. Press any top row Select key to enter

a custom number. Custom numbers can only be a number between 16-32.

The default is the DMP value of 16 which is pre-programmed.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

deviCe SeTuP

6.15.9 REqUIRE SITE

Require Site Code

Press the top row Select key under YES to use a site code.

CODE?

NO YES

In addition to User Code veriﬁcation, door access is only granted when any one site

code programmed at the SITE CODE ENTRY option matches the site code received in

the Wiegand string.

6.15.9 .1

Site Code Display

You can program up to eight three-digit site codes. Site code range is 0-999.

Any previously programmed site codes display. Dashes represent blank site

codes.

SITE CODE 1: -

Site Code 1 displays ﬁrst. Enter a three-digit site code number followed by

the command key to advance to the next prompt, Site Code 2. To delete

an existing site code, press any select key. Either enter a new site code

followed by command, or press command to leave blank and continue to the

next site code. Repeat these steps to change, delete, or add up to 8 site

codes.

Note: A card with a site code greater than three digits cannot be used.

Use only cards with three-digit site codes.

NO OF USER CODE

6.15.10

6.15.11

Number of User Code Digits

DIGITS:

The 734 module recognizes user codes from four to ten digits in length. Press any

top row Select key to enter a user code digit length between 4-10 digits. This

number must match the user code number length being used by the panel. Default

is 5. For an XR500 Area System, use 4 to 10 digits (typically 5). For all other systems

and panels, use 4 digits.

Any selection above 5 digits require entry of the custom card deﬁnitions with custom

site and user code positions for the Wiegand string. When searching the bit string

for the user code, the digits are identiﬁed and read from left to right.

Degraded Mode

This option deﬁnes the relay action when communication with the panel has not

occurred for ﬁve seconds. Press any top row Select key to display relay action

options. Press the Back Arrow key to return to the NO OF USER CODE DIGITS:.

Choose the Degraded Mode Action required.

DEGRADED MODE:

OFF SITE ANY ON

Press the ﬁrst Select key to choose OFF [Default] (Relay Always Off) — The relay

does not turn on when any Wiegand string is received. Off does not affect any REX

operation.

DEGRADED MODE:

RELAY ALWAYS OFF

DEGRADED MODE:

ACCEPT SITE CODE

Press the second Select key to choose SITE (Accept Site Code) — Door access

is granted when the Wiegand site code string received matches any site code

programmed at SITE CODE ENTRY. For details refer back to the REQUIRE SITE CODE

option.

DEGRADED MODE:

ANY WIEGAND READ

Press the third Select key to choose ANY (Any Wiegand Read) — Door access is

granted when any Wiegand string is received.

DEGRADED MODE:

RELAY ALWAYS ON

Press the fourth Select key to choose ON (Relay Always On) — The relay is always on.

Press the COMMAND key to display the next action.

DEGRADED MODE:

LAST

Press the ﬁrst Select key to choose LAST (Keep Last State) — The relay remains in the

same state and does not change when communication is lost.

DEGRADED MODE:

PRESERVE LAST

After choosing the action, the DEGRADED MODE option and the newly deﬁned action

display.

Programming is now complete. Press the COMMAND key to display DEVICE NO. Press

the Back Arrow to return to the NO OF USER CODE DIGITS option.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

remoTe oPTionS

Remote Options

REMOTE OPTIONS

REMOTE KEY:

7.1

7.2

Remote Options

This section allows you to enter the information needed for Remote Command/

Remote Programming operation.

Remote Key

This option allows you to enter a code of up to 16 characters. The Remote Link™

program must give the correct key to the panel before being allowed any remote

functions. All panels are shipped from the factory with the key preset as blank.

To enter a remote key or change the current one, press a top row Select key and

enter any combination of up to 16 digits. Press COMMAND. The current key display

as astericks.

7.3

7.4

Remote Disarm

REMOTE DISARM?

YES allows the panel to be disarmed remotely. NO disables remote disarming.

Default is NO.

NO YES

Allow Dialer Remote

ALLOW DIALER

YES allows remote programming over the phone line. Default is YES.

Receiver Key Operation:

REMOTE?

NO YES

With YES selected, the panel requests the receiver’s key during its ﬁrst message to

the SCS-1R Receiver and this becomes the alarm receiver key. A receiver key is an

alphanumeric code programmed into the receiver and identiﬁes it to alarm panels.

The panel retains this alarm receiver key in memory and allows remote commands

to be accepted over the dialer from the alarm receiver. If an alarm occurs during

a remote connect, the alarm report is immediately sent to the alarm receiver and

does not appear at the remote programming software.

YES also enables remote commands and programming to be accepted from a

secondary receiver other than the alarm SCS-1R Receiver. The panel requests

the service receiver key the ﬁrst time it is contacted by another receiver and this

becomes the service receiver key. The panel retains this service receiver key in

memory and accepts remote commands from the service receiver. If an alarm occurs

during a remote connect, the panel disconnects from the service receiver and calls

the alarm receiver. Alarm reports are only sent to the alarm receiver.

It is important that the alarm receiver key and the service receiver key programmed

into the receiver at the central station are NOT the same so the panel can determine

the difference between receivers.

When NO is selected, remote commands and programming are not accepted from the

SCS-1R Receiver using digital dialer and all memory of receiver keys is cleared.

7.4.1

Armed Answer Rings

ARMED ANSWER

RINGS:

Enter the number of rings the panel counts before answering the phone line when

all system areas are armed. Any number from 0 to 15 can be entered. If 0 (zero)

is entered, the panel does not answer the phone when all system areas are armed.

The default is 8 (eight).

Answering machine bypass procedure: Entering a number greater than 0 (zero) into

either Armed Rings or Disarmed Rings, allows a central station operator to connect

remotely with the panel.

How it works: The operator calls the panel, allows the telephone to ring one time,

and then hangs up. The panel stores this as an attempt to communicate. The

operator then calls back within 30 seconds. The panel seizes the telephone line to

allow remote programming.

Note: This feature does not interfere with the normal operation of the Arm Rings or

Disarm Rings functions.

7.4.2

Disarmed Answer Rings

DISARMED ANSWER

RINGS:

Enter the number of rings the panel counts before answering the phone line while

any system areas are disarmed. Any number from 0 to 15 can be entered. If 0 (zero)

is entered, the panel does not answer the phone when any system area is disarmed.

The default number is 8 (eight).

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

remoTe oPTionS

7.4.3

7.4.4

PC Modem

PC MODEM NO YES

YES allows the panel to answer the telco link and connect with Remote Link through

the PC Modem at 2400 baud. NO disables PC Modem communication.

Manufacturer Authorization

MANUFACTURER

Select YES to allow DMP Technical Support technicians to access the panel during

system service or troubleshooting. This authorization automatically expires within

one hour.

AUTH?

NO YES

DMP remote service is provided on a read only basis: DMP technicians can look

at the system programming and make suggestions only. Alterations can only be

accomplished by installing company service personnel.

ALLOW NETWORK

7.5

Allow Network Remote

REMOTE?

NO YES

This option displays only if the panel has network capability. YES allows remote

programming over the network. Changing this prompt does not change any other

network programming prompts. Default is YES.

7.5.1

Network Programming Port

Enter the programming port number. The programming port identiﬁes the port used

to communicate messages from the panel. The default Programming Port setting is

2001.

NETWORK PROG

PORT:

2001

7.5.2

7.6

Encrypt Network Remote

ENCRYPT NETWORK

YES encrypts data sent over network. Default is NO.

REMOTE?

NO YES

Allow Cellular Remote

ALLOW CELL

REMOTE?

YES allows remote programming using cellular connection. Default is YES.

NO YES

7.6.1

First GPRS APN

FIRST GPRS APN:

Enter the ﬁrst APN (Access Point Name). This allows an access point for cellular

communication and is used to connect to a DNS network. The APN may contain two

lines of 16 characters to equal 32 characters. Default is set to SECURECOM400.

SECURECOM400

Second GPRS APN

SECOND GPRS APN:

Enter the second APN (Access Point Name). This works as a backup in case the ﬁrst

APN fails. The APN may contain two lines of 16 characters to equal 32 character

Default is set to SECURECOM400.

SECURECOM400

ENCRYPT CELL

7.6.2

Encrypt Cellular Remote

REMOTE?

NO YES

YES encrypts data sent over a cellular connection. Default is NO.

7.7

7.8

Allow RS-232 Remote

ALLOW 232

REMOTE?

YES allows remote programming over the on-board RS-232 port. Default is YES.

NO YES

Entré Connection

ENTRE

CONNECTION: NONE

This option displays only if the panel has network capability. Select NET to allow

a dedicated network connection with Entré. Options are NONE or NET. Default is

NONE.

7.8.1

7.8.2

Entré Incoming TCP Port

ENTRE INCOMING

This option displays only if NET is chosen for the Entré connection. Enter the

programming port number for the incoming Entré connection. The programming port

identiﬁes the port used to communicate messages to and from the Entré software.

This port cannot be the same port as programmed in Network Programming Port.

The default Programming Port setting is 2011.

TCP PORT:

2011

Entré IP Address

ENTRE IP

This option displays only if NET is chosen for the Entré connection. Enter the Entré

IP address where the panel sends network messages. The Entré IP Address must be

unique and cannot be duplicated on the network. Enter all 12 digits and leave out

the periods. For example, enter IP address 192.168.0.250 as 192168000250. The

periods display automatically. Default is 0.0.0.0

000.000.000.000

7.8.3

Entré Outbound TCP Port

ENTRE OUTBOUND

TCP PORT: 2001

This option displays only if NET is chosen for the Entré connection. Enter the

programming port number for the outbound Entré connection. The programming port

identiﬁes the port used to communicate messages to the Entré software. Default is

2001.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

remoTe oPTionS

7.8.4

Entré Backup IP Address

ENTRE BACKUP IP:

000.000.000.000

This option displays only if NET is chosen for the Entré connection. Enter the IP

backup address where the panel sends network messages if the ﬁrst Entré IP Address

fails. The Entré IP Address must be unique and cannot be duplicated on the network.

Enter all 12 digits and leave out the periods. For example, enter IP address

192.168.0.250 as 192168000250. The periods display automatically. Default is

0.0.0.0

7.8.5

7.8.6

7.8.7

7.9

Entré Backup TCP Port

ENTRE BACKUP TCP

This option displays only if NET is chosen for the Entré connection. Enter the

backup programming port number for the outbound Entré connection in case the

connection to the primary IP fails. Default is 2001.

PORT:

2001

Entré Checkin

ENTRE CHECKIN

MINUTES:

Select the rate at which check-in messages are sent over the Entré connection.

Select 0 (zero) to disable check in messages. Range is 0, 3-240 minutes.

Default is 0.

Entré Passphrase

To enable encryption enter an 8 to 16-character Passphrase using alphanumeric

characters. If you leave the Passphrase blank, the panel communicates with Entré,

but the data is not encrypted. The Passphrase is blank by default.

ENTRE PASSPHRASE

Send Local Changes

This option allows the panel to automatically update Remote Link at the central

station with any changes made to the panel.

SEND LOCAL

CHANGES? NO

Select NET or DD to send local programming changes or User Menu changes to user

codes, user proﬁles, schedules, or holiday dates to Remote Link after exiting the

programming or User Menu. If NET is selected, changes are sent using Network. If

DD is selected, changes are sent using Dialer. Default is NO to disable this feature.

SEND LOCAL

NO NET DD

7.9.1

Remote Change IP

REMOTE CHANGE IP

000.000.000.000

This option displays when NET is selected for Send Local Changes. Enter the IP

address containing up to 12 digits. The Net IP Address must be unique and cannot

be duplicated on the network. Enter all 12 digits and leave out the periods. For

example, enter IP address 192.168.0.250 as 192168000250. The periods display

automatically. Default is 000.000.000.000

REMOTE CHANGE

7.9.2

7.9.3

Remote Change Port

This option displays when NET is selected for Send Local Changes. Enter the Port

number. Valid numbers are from 0 to 65535. Default is 2002.

PORT:

2002

Remote Telephone Number

This option displays when DD is selected for Send Local Changes. Press COMMAND to

enter the phone number the panel dials when sending programming changes. After

entering a phone number, the panel sends any panel changes to Remote Link.

REMOTE PHONE NO.

The phone number can have two lines of 16 characters each to equal 32. Enter a

P to program a two second pause in the dialing sequence. The P character counts

as part of the 32 allowable characters. Enter *70P as the string ﬁrst characters to

cancel call waiting. Dial tone detect is an automatic panel function.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

SySTem rePorTS

System Reports

SYSTEM REPORTS

8.1

8.2

System Reports

Select speciﬁc system reports the panel sends to the receiver.

ABORT

NO YES

Abort Report

YES allows the panel to send an alarm abort report to the receiver any time an area

is disarmed during Transmit Delay before an alarm report is sent and the Bell Cutoff

Time has not expired. After disarming an area, if any other area remains armed and

has zone(s) in alarm, the alarm abort report is not sent.

If the communication type is set to DD, a Warning: Alarm Bell Silenced report is also

sent if the alarm bell is silenced.

Note: Abort Reports are not sent for Fire, Fire Verify, or Supervisory type zones.

RESTORAL:

YES

8.3

Restoral Reports

This option allows you to control when and if a zone restoral report is sent to the

central station receiver. Press any Select key to display the following options:

YES

DISARM

NO - Disables the zone restoral report option. Zones continue to operate normally

but do not send restoral reports to the receiver.

YES - Enables the zone restoral report option. Zone restorals are sent whenever a

zone restores from a trouble or alarm condition.

DISARM - Causes the panel to send restoral reports for a non-24-hour zone whenever

a zone that has restored from a trouble or alarm condition is disarmed. All 24-hour

zones send restoral reports as they restore.

BYPASS

NO YES

8.4

8.5

8.6

Bypass Reports

YES allows the panel to send all zone bypasses, resets, and force arm reports to the

receiver. The bypass report includes the zone number, zone name, and the user

name and number of the individual operating the system. Reports are only sent if

O/C User in Communications is set YES for Receiver 1 or Receiver 2.

SCHD CHG NO YES

CODE CHG NO YES

Schedule Change Reports

YES allows the panel to send all schedule changes to the receiver. The report

includes the day, opening time, closing time, extend schedule time, and the user

name and number of the individual making the change. Schedule changes made

through Remote Link™ are not sent to the printer or Display Events.

Code Change Reports

YES allows the panel to send all code additions, changes, and deletions to the

receiver. The code change report includes the user name and number added or

deleted and the user name and number of the individual making the change. Code

changes made through Remote Link™ are not sent to the printer or Display Events.

Reports are only sent if O/C User in Communications is set YES for Receiver 1 or

Receiver 2. The default setting is YES.

ACCESS KEYPADS:

8.7

Access Keypads

Select the keypad addresses (1 through 16) that send door access reports to the

receiver. Enter the keypad number using the digit keys. An asterisk next to the

number indicates that the keypad is selected. Press COMMAND to display the next

set of keypads.

A report is sent with each door access made from the selected keypads. Keypads at

addresses not selected still operate the door relay but do not send access reports.

The report includes the user number, user name, keypad address, and device name.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

SySTem rePorTS

AMBUSH

NO YES

8.8

Ambush

YES allows an ambush report to be sent anytime user code number 1 is entered at

a keypad. NO disables the ambush report and allows user number 1 to operate the

same as all other codes.

PANIC TST NO YES

8.9

Panic Test Communication (XR500N/XR500E only)

YES allows the panic zone test veriﬁcation and failure results to be sent to the

central station receiver. NO disables the panic test report. The default setting is

NO. The system test start, stop, panic zone veriﬁcation, and panic zone failure

messages sent to the central station and the trips count operation are the same as

used under the Walk test. See Using the Walk Test section in the Appendix.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

SySTem oPTionS

System Options

SYSTEM OPTIONS

9.1

9.2

System Options

This section allows you to select system-wide parameters.

System

This option allows you to program how the areas operate for arming and disarming.

The options you can choose are listed below:

SYSTEM:

AREA

AREA - All 32 areas can be programmed and operated independently.

ALL/PERIMETER - Area 1 is the Perimeter and Area 2 is the Interior.

AREA A/P H/A GST

HOME/SLEEP/AWAY - Area 1 is the Perimeter, Area 2 is the Interior, and Area 3 is the

Bedrooms. With the HOME/SLEEP/AWAY option, the user can:

1. Select HOME to arm just the perimeter.

2. Select SLEEP to arm the perimeter and interior (non bedroom areas).

3. Select AWAY to arm all three areas.

Note: A Home/Sleep/Away system can be conﬁgured to use all three areas or

only use the Home and Away areas.

HOME/SLEEP/AWAY WITH GUEST- This allows the alarm system to be divided into a

main house HOME/SLEEP/AWAY system and two other guest houses that also are set

up as HOME/SLEEP/AWAY systems.

Areas 1, 2, and 3 are the Perimeter, Interior, and Bedrooms for the Main house

system. Areas 4, 5, and 6 are the Perimeter, Interior, and Bedrooms for the Guest

1 house system. Areas 7, 8, and 9 are the Perimeter, Interior, and Bedrooms for

the Guest 2 house system. These areas are automatically assigned per system and

cannot be changed. See Display Areas in Device Setup to assign keypads to a system.

Zones are assigned to a system by assigning the system’s area numbers to the zone in

Zone Information programming.

When either All/Perimeter or Home/Sleep/Away is selected, the area names are

automatically assigned and cannot be modiﬁed.

Note: Areas 3-32 in an All/Perimeter system, areas 4-32 in a Home/Sleep/Away

system, and areas 10-32 in a Home/Sleep/Away with Guest system are not available

for use and are initialized.

INST ARM NO YES

9.3

Instant Arming

When YES is selected, the arming keypad displays INSTANT for selection during the exit

countdown delay when arming fewer than all areas of the system. At the time instant

arming is selected, any entry and exit delays programmed for the areas being armed

are ignored. The entry delay for previously armed areas is not affected by instant

arming. When NO is selected, INSTANT does not display during arming. Default is NO

for an Area System, and YES for an All/Perimeter or Home/Sleep/Away system.

CLS WAIT NO YES

9.4

9.5

Closing Wait

When YES is selected, the keypad displays ONE MOMENT... while waiting for

an acknowledgement from the receiver before arming the selected area(s) and

performing a Bell Test (if selected). Exit delays begin after the Closing Wait.

Opening/Closing reports must be YES to enable Closing Wait.

ENTRY DLY 1:

ENTRY DLY 2:

ENTRY DLY 3:

ENTRY DLY 4:

Entry Delay 1

Enter the Entry Delay time for all Exit type zones programmed to use Entry Delay 1.

When an armed Exit type zone is faulted, the keypad prewarn tone begins sounding.

All keypads programmed to prewarn for that zone display ENTER CODE:- and the

name of the zone causing the entry delay. When the ﬁrst digit of a code is entered,

the prewarn tone stops at that keypad. If an invalid code is entered, the prewarn

tone begins sounding again. The area must be disarmed before the delay expires

or an alarm report is sent to the receiver and an alarm sounds. All zones in that

area are delayed along with the Exit zone. Entry Delay times can be from 30 to 250

seconds. Repeat the above for each entry delay being used in the system.

120

Note: Speciﬁc Exit Error operation is based on the Entry Delay used (1-4) with an EX

type zone. See Exit Delay.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

SySTem oPTionS

CRS ZONE TM:

9.6

Cross Zone Time

Enter the time allowed between zone faults. When zones are cross zoned, the same

zone or a second cross zoned zone must fault within this time in order for an alarm

report for both zones to be sent to the receiver. If the cross zone time expires

without the second zone faulting, only a zone fault from the ﬁrst zone is reported.

Cross-zone time can be from 4 to 250 seconds. Entering 0 (zero) disables this

function. Default is 4. See the Appendix.

RETARD DELAY:

PWR FAIL HRS:

9.7

9.8

Zone Retard Delay

Enter the retard time assigned to Fire, Supervisory, Auxiliary 1, Auxiliary 2, Arming,

and Panic type zones. The retard delay only functions when the zone is shorted.

The zone must remain shorted for the entire length of the Retard Delay before being

recognized by the panel. The Zone Retard Delay can be from 1 to 250 seconds.

Entering a 0 (zero) disables this function.

Power Fail Delay

This option tracks the duration of an AC power failure. When the AC power is off for

the length of the programmed delay time, an AC power failure report is sent to the

receiver. The delay time can be from 1 to 15 hours. Entering a 0 (zero) sends the

power failure report after a 15-second delay. The default setting is 1.

SWGRBYPS TRIPS: 1

9.9

Swinger Bypass Trips

Enter the number of times (1 or 2) a zone can go into an alarm or trouble condition

within one hour before being automatically bypassed. You can select one or two

trips. Bypassed zones are automatically reset when the area they are assigned to is

disarmed. All 24-hour zones are reset when any area of the system is disarmed. A

programming Stop operation restores a bypassed zone. Entering 0 (zero) disables

this function. Default is 1.

How it works

The panel hour timer starts at 59 minutes past the hour. If the hour timer expires

before the trip counter is exceeded, the trip counter returns to 0 (zero). If the trip

counter is exceeded before the hour expires, the zone is automatically bypassed by

the panel. A Bypass Report is sent to the receiver if Bypass Reports is YES.

9.10

9.11

Reset Swinger Bypass

RST SBYP NO YES

When YES is selected, an automatically bypassed zone is reset if it remains in a

normal condition for one complete hour after being bypassed. A report of the

automatic reset is sent to the receiver if Bypass Reports has been selected as YES.

Default is NO.

TIME CHG NO YES

Time Zone Changes

This function allows the panel to request automatic time changes from the DMP

SCS-1R Receiver on Path 1. For the receiver to send time changes, it must be

programmed to send time changes and must be receiving time change updates from

the network automation computer at least every 24 hours. Default is YES.

HRS FROM GMT:

When time zone is programmed YES, enter the number (0-23) that indicates the

Greenwich Time zone (GMT) where the panel is located. The default is 6.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

SySTem oPTionS

GMT City/Time Zone

London, Monrovia, Lisbon, Dublin, Casablanca, Edinburgh

New Cadelonia

Cape Verde Island, Azores

Guam, Sydney

Mid-Atlantic, Fernando de Noronha

Buenos Aires, Georgetown, Brasilia, Rio de Janeiro

Atlantic Time (Canada), Caracas, La Paz, Santiago

Eastern Time (US, Canada) Bogota, Lima, Arequipa

Central Time (US, Canada), Mexico City, Saskatchewan

Mountain Time (US, Canada), Edmonton

Paciﬁc Time (US, Canada), Tijuana

Alaska

Tokyo, Seoul

Hong Kong, Singapore

Bangkok, Hanoi

Dhaka, Almaty

Islamabad, Karachi

Abu Dhabi, Kazan

Moscow, Bagdad

Eastern Europe

Rome, Paris, Berlin

Hawaii

Midway Island, Samoa

Fiji, Marshall Island, Wellington, Auckland, Kwajalein, Kamchatka

LATCH SV NO YES

9.12

9.13

Latch Supervisory Zones

Selecting YES latches supervisory zone alarms on the keypad display until the sensor

reset operation is performed. Selecting NO automatically clears the alarm from the

keypad display when the supervisory zone restores to a normal condition. Default is YES.

PROG LANGUAGE

Programming Menu Language

Press the COMMAND key to select the programming language. Any changes in PROG

LANGUAGE do not take effect until the STOP routine completes.

PRI LANG: ENGLSH

The current primary programming language displays. The default language is

English. Press a Select key to change the primary programming language.

ENG SPN FRN

Select the primary programming language.

ENG = English (ENGLISH)

SPN = Spanish (ESPANOL)

FRN = French (FRANCAIS)

SEC LANG:

NONE

The current secondary programming language displays. Selecting a secondary

language allows the installer to view programming in English, Spanish, or French.

When the Programming Menu is accessed, the installer is prompted to choose the

programming display language. If SEC LANG: is set to NONE, the option to choose

a language does not display. To select a secondary language, press the Select key

below the language. Default is NONE.

NONE ENG SPN FRN

Select the secondary programming language.

NONE = No secondary language options are displayed

ENG = English (ENGLISH)

SPN = Spanish (ESPANOL)

FRN = French (FRANCAIS)

USER LANGUAGE

9.14

User Menu and Status List Language

Press the COMMAND key to select User language.

PRI LANG: ENGLSH

ENG SPN FRN

The current primary user language displays. The default language is English. Press a

Select key to change the primary User language.

Select the primary user language.

ENG = English (ENGLISH)

SPN = Spanish (ESPANOL)

FRN = French (FRANCAIS)

SEC LANG:

NONE

The current secondary user language displays. Selecting a secondary user language

allows the user to view the User Menu and Status List text in English, Spanish, or

French. When the User Menu is accessed, the user is prompted to choose the display

language. Status List text displays in the selected language until another language

is chosen. If SEC LANG: is set to NONE, the option to choose a language does not

display. To select a secondary language, press the Select key below the language.

Default is NONE.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

SySTem oPTionS

For example, when Spanish is selected at a keypad, the User Menu and Status List

text display in Spanish at that keypad. When the user later accesses the keypad,

pressing the COMMAND key once displays the option for English, Spanish, or French.

Pressing the COMMAND key again continues to display the Status List text in Spanish.

Later on, if English or French is selected at that keypad, the User Menu and Status

List text display in the selected language at that keypad.

NONE ENG SPN FRN

Select the secondary user language.

NONE = No secondary language options are displayed

ENG = English (ENGLISH)

SPN = Spanish (ESPANOL)

FRN = French (FRANCAIS)

BYPASS LIMIT

9.15

9.16

Bypass Limit

Enter the maximum number of zones (0 to 8) that can be bypassed in any single area

when that area is being armed at a keypad. If more zones than the limit are in a

non-normal state or already bypassed at arming, arming does not occur and Arming

Stopped displays. The Bypass limit does not affect auto arming or keyswitch arming.

Entering 0 (zero) allows no limit. Default is 0 (zero).

Card Plus PIN (XR500E only)

CARD PLUS PIN:

Select YES to require all users to present a proximity credential and enter a PIN

number wherever user code entry is required for system functions accessed from a

keypad. Select NO to disable Card Plus PIN operation. Default is NO.

Note: The Card Plus PIN option is not designed to operate with All/Perimeter or

Home/Sleep/Away systems.

NO YES

For an XR500E system using Card Plus PIN, two code entries are required by a user to

operate the system from a keypad. The ﬁrst must be a code entered from a Wiegand

interface device (card, fob, etc.) using a reader such as the built-in reader of a DMP

Keypad. An external reader may also be used. The second code (User Pin) is keyed

in at the keypad or could be a second card or fob.

For a Card Plus PIN system, user codes (Card and PIN) are typically administered

using DMP System Link software.

When this option is ﬁrst turned on at a keypad, the factory default (user number

9999, user code 99) must be available to enter the user menu at a keypad to then

add user codes and PIN numbers or to change existing users to add their PIN number.

If user 9999 was previously removed, re-enter this user and then set Card Plus

Pin = YES. Afterwards, user 9999 can be removed and the system only allows card

plus PIN entries.

Note: Current users of an existing system are immediately affected in that they must

have their user code information changed to add the user PIN.

9.17

House Code

WIRELESS

HOUSE CODE: 0

When using a DMP wireless system, enter a house code between 1 and 50. When

using FA Series wireless enter 99. See Wireless programming in Zone Information.

Default is 0 indicating no wireless system is being used.

The DMP house code identiﬁes the panel, DMP receiver, and DMP transmitters to

each other. When operating, the DMP receiver listens for transmissions that have

the programmed house code and transmitter serial number.

Note: The ﬂexibility of DMP two-way wireless operation allows an existing house

code to be changed in the panel at any time. The transmitters may take up to two

minutes to learn the new house code and continue operation.

Note: When any wireless zone programming is changed in the panel, wireless

receiver zone programming is updated. At that point, all wireless zones display as

normal for approximately 1 minute, regardless of the actual state of the zone.

9.18

Detect Wireless Jamming

DETECT WIRELESS

JAMMING: NO YES

This option displays when the House Code entered is for a DMP 1100 Series Wireless

system (1-50). When enabled and the wireless receiver detects jamming, a trouble

or alarm message displays in the Status List and is sent to the central station

receiver. Select YES to enable jamming messages to display in the Status List.

Select NO to disable jamming messages. Default is NO.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

SySTem oPTionS

9.19

Wireless Audible Annunciation

WLS AUDIBLE: DAY This option displays when the House Code entered is for a DMP 1100 Series Wireless

system (1-50). Press any top row key to select the keypad buzzer annunciation

WIRELESS AUDIBLE

ANY DAY MIN

method for wireless low battery and missing messages. Select ANY to enable

annunciation anytime. Select DAY to enable annunciation except during sleeping

hours (9 PM to 9 AM). Select MIN (minimum) to annunciate only Fire and Fire Verify

zones during daytime hours (9 AM to 9 PM). Default is DAY.

9.20

9.21

Enable Keypad Panic Keys

KEYPAD PANIC KEYS

This option allows the two-button panic key operation selected at the keypad to

send the Panic, Emergency, or Fire message to the central station receiver. Select

YES to enable the two-button panic operation to operate. To disable the two-button

panic operation, select NO. Default is YES.

ENABLED: NO YES

Occupied Premises

OCCUPIED

PREMISES: NO YES

For All/Perimeter or Home/Sleep/Away systems, select YES to allow the panel to

automatically disarm the interior area(s) when arming all areas and a perimeter

zone is not tripped during the exit delay. Select NO to disable this feature. Default

is YES.

Note: With a Home/Sleep/Away with Guest arming system, this feature only applies

to the main system.

9.22

Enhanced Zone Test

ENHANCED ZONE

Select YES to allow enhanced zone test operation. The default is NO.

NO YES

TEST:

Enhanced operation allows:

• Panic Test and Walk Test functions can be restricted to operate only during an

Area 32, Shift 4 schedule if programmed. If no schedule is entered, the walk

test always operates.

• A Verify message is sent each time a zone is tested. If a zone is tripped

multiple times, a Verify message is sent for each trip. This allows the Central

Station to record the number of devices per zone.

• The Verify message for each zone test is sent at the time the trip occurs

instead of at the end of Walk Test.

• The System Test Begin and System Test End Central Station messages indicate

the type of zone being tested. The System Test Begin message also includes

the user name and number.

9.23

9.24

Dual EOL

DUAL EOL NO YES

Select YES to enable the use of dual 1K EOL resistors on panel zones one to eight.

This zone operation is used for medium or high risk ULC Listed applications. Please

see Dual EOL section in the XR500 Series Canadian Installation Guide for complete

details. Select NO to disable this feature. Default is YES.

Send 16 Character Names

This option allows central stations to select being sent either the ﬁrst 16 characters

of the name ﬁeld or the entire programmed name, up to 32 characters, for user

name, user proﬁle, zone name, area name, output name, and group name.

SEND 16 CHAR

NAMES:

NO YES

Select YES to have the ﬁrst 16 characters of the name ﬁeld sent to the central

station. Select NO to send the exact number of characters entered in the name ﬁeld

from 1 up to the maximum of 32 characters. Default is YES.

Note: Using 32 character names increases the length of the DMP Serial 3 message

from the panel to the receiver. The SCS-1R receiver does not require an update to

pass these messages to the Host Automation System of the Central Station. Before

using names longer than 16 characters, determine whether the Host Automation

System of your Central Station can accept 17 to 32 character names. If not, only use

16 character names.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

bell oPTionS

Bell Options

10.1

10.2

Bell Options

This section allows you to program the panel bell output functions.

BELL OPTIONS

Bell Cutoff Time

Enter the maximum time from 1 to 99 minutes the Bell Output remains on. If the

area is disarmed, the cutoff time resets. Enter 0 (zero) to provide continuous bell

output. The default is 15 minutes.

BELL CUTOFF: 15

Note: To support the Alarm Verify feature on an All/Perimeter or Home/Sleep/Away

system, set the Bell Cutoff Time to greater than 0.

Note: For SIA CP-01 False Alarm Reduction Installations, the Bell Cutoff Time must

be set to a minimum of six (6) minutes.

10.3

Automatic Bell Test

Select YES to turn on the Bell Output for 2 seconds each time the system is

completely armed from a keypad. This test is delayed until the Closing Wait

acknowledge is received (if programmed). If the Closing Wait acknowledge is not

received within 90 seconds, the bell test does not occur. Arming performed from an

Arming zone or from Remote Link™ does not activate the Bell Test.

BELL TST NO YES

10.4

10.5

Bell Output

Enter the output number when needed to follow the panel Bell Output operation for

all action and off conditions. Enter 0 (zero) to disable.

BELL OUTPUT:

Note: When BELL ACTION is set to T for Temporal Code 3, the Bell Output action for

an LX-Bus output is pulse.

Bell Action

This section deﬁnes the type of Bell Output for zone alarms. Press COMMAND to

display the default Bell Output for each zone type. Press any Select key and enter

S for a Steady Bell Output, P for a Pulsed output, T for a Temporal Code 3 output,

and N for no Bell Output.

BELL ACTION . . . . .

Note: Trouble conditions do not activate the Bell Output.

10.5.1

10.5.2

10.5.3

10.5.4

10.5.5

10.5.6

10.5.7

Fire Bell Action

Deﬁnes Bell Action for Fire Type zones. The default is P.

FIRE

TYPE:

Burglary Bell Action

Deﬁnes Bell Action for Burglary Type zones and Exit Error output. The default is S.

BURGLARY TYPE: S

SUPRVSRY TYPE: N

Supervisory Bell Action

Deﬁnes Bell Action for Supervisory Type zones. The default is N.

Panic Bell Action

Deﬁnes Bell Action for Panic Type zones. The default is N.

PANIC TYPE:

EMERGNCY TYPE:

AUXLRY 1 TYPE:

AUXLRY 2 TYPE:

Emergency Bell Action

Deﬁnes Bell Action for Emergency Type zones. The default is N.

Auxiliary 1 Bell Action

Deﬁnes Bell Action for Auxiliary 1 Type zones. The default is N.

Auxiliary 2 Bell Action

Deﬁnes Bell Action for Auxiliary 2 Type zones. The default is N.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

ouTPuT oPTionS

Output Options

11.1

Output Options

This section allows you to program panel output options. The panel provides two

Form C relays (1 and 2) and four switched ground (open collector) outputs numbered

3 to 6. Expand the system up to 500 additional relay outputs using J22 LX-Bus on

the panel, multiple 716 Output Expander Modules, and up to ﬁve interface cards. In

addition, 45 wireless outputs are available when using the 1100X wireless receiver.

Refer to the XR500 Series Canadian Installation Guide (LT-0681) for complete

information.

OUTPUT OPTIONS

Select from the following output numbers:

• 1 to 6

• 450 to 474 — Slow response time* wireless outputs (activates within 15 seconds)

• 480 to 499 — Fast response time* wireless outputs (activates within 1 second)

• 500 to 999 — LX-Bus output, Relay output, Zone expansion output

• D1 to D16 — Keypad door strike relay for addresses 1-16

• G1 to G20 — Output group

* The response time of a wireless output is the time it takes for a wireless output to

activate once the panel event occurs. You determine whether a wireless output is a

slow or fast response based on the output number assigned. A slow response output

number extends battery life, but response time may be up to 15 seconds. A fast

response output number responds within 1 second, but reduces battery life. Refer

to the speciﬁc wireless output installation guide to determine battery life.

11.2.1

Cutoff Output

Outputs 1 to 6 can be entered here to turn off after a time speciﬁed in CUTOFF

TIME. To disable this option, press any Select key to clear the display then press

COMMAND. The Cutoff Output displays dashes when no outputs are selected.

CO OUTS: - - - - - -

11.2.2

11.3

Output Cutoff Time

If a Cutoff Output (1-6) is assigned, enter a Cutoff Time of 1 to 99 minutes for the

output to remain on. Enter 0 (zero) for continuous output.

CUTOFF TIME:

Communication Trouble Output

Enter the output number to turn on when a DD system fails to communicate on

three successive dial attempts or if the backup communication line transmits a

report. The Communication Trouble Output also turns on when NET is selected

as the primary communication method and NET communication fails after one

minute. When NET communication is restored the Communication Trouble Output

automatically turns off.

COMM TRBL OUT: 0

To manually turn the output off, disarm any area or select Off for the output number

in the User Menu Outputs On/Off section. Enter 0 (zero) to disable this output.

11.4

11.5

Fire Alarm Output

Enter the output number to turn on when a ﬁre type zone is placed in alarm. The

output is turned off using the Sensor Reset option while no additional ﬁre type zones

are in alarm. Enter 0 (zero) to disable. This output is not compatible with Cutoff

Outputs.

FIRE ALR OUT:

FIRE TRB OUT:

Fire Trouble Output

Enter the output number to turn on when a ﬁre type zone is placed in trouble, when

a supervisory type zone is placed in alarm or trouble, or when any system monitor

(AC, Battery, Phone Line 1 or Phone Line 2) is placed in trouble. The output turns off

when all ﬁre and supervisory type zones, or system monitors are restored to normal.

Enter 0 (zero) to disable this output. This output is not compatible with Cutoff

Outputs. This output can be connected to a lamp, LED, or buzzer using the DMP

Model 716 Output Expansion Module.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

ouTPuT oPTionS

11.6

Panic Alarm Output

Enter the output number to turn on when any Panic type zone is placed in an alarm

condition. The output is turned off after all Panic zones are restored from an alarm

condition and a Sensor Reset is performed. Enter 0 (zero) to disable.

PANIC ALM OUT:

Wireless Outputs

• The Panic Alarm is compatible with the Model 1118 Wireless Remote Indicator

Light and the Model 1116 Wireless Relay Output connected to a Model 572

Indicator LED.

• When a Panic Alarm occurs, the LED turns on steady for ﬁve minutes and then

turns off.

• When a Panic Test is initiated from the keypad, the LED ﬂashes quickly for ﬁve

minutes.

• For a Panic Alarm, a fast response wireless output number is recommended.

11.7

11.8

Ambush Output

Enter the output number to turn on when an Ambush code is entered at a keypad.

The output is turned off using the Sensor Reset option. Enter 0 (zero) to disable.

AMBUSH OUT:

ENTRY OUT:

Entry Output

Enter the output number to turn on at the start of the entry delay time. The output

turns off when the area is disarmed or the entry delay time expires. Enter 0 (zero)

to disable.

11.9

Exit Output

Enter the output number to turn on when an exit delay time starts in any area of

the system. The output turns off when the area arms or when the arming has been

stopped. Enter 0 (zero) to disable.

EXIT OUT:

11.10

Ready Output

Enter the output number to turn on when all disarmed burglary zones are in a

normal state. The output is turned off when any disarmed burglary type zone is in

a bad state. Enter 0 (zero) to disable. This output is not compatible with Cutoff

Outputs.

READY OUT:

11.11

11.12

Telephone Trouble Output

Enter the output number to turn on when the phone line monitor on the panel phone

line is lost. Enter 0 (zero) to disable this output.

PH TRBL OUT:

LATE CLS OUT:

Late To Close Output

Enter the output number to turn on at the expiration of a Closing schedule. The

output activates simultaneously with the CLOSING TIME! keypad display. The output

is turned off when the area is armed, the Closing is extended, or the schedule is

changed. Enter 0 (zero) to disable this output.

11.13

11.14

Device Fail Output

Enter the output number to turn on when an addressed device fails to respond to

polling from the panel. A Missing Device report is sent to the receiver. The output

is turned off when the device responds to polling or is removed from programming in

the system. Enter 0 (zero) to disable this output and LX-Bus™ device fail reporting

to the receiver. If any addressed device is unsupervised, this output cannot be used.

DVC FAIL OUT:

SNSR RST OUT:

Sensor Reset Output

Enter the output number to turn on when a Sensor Reset is performed at a keypad.

The output turns off automatically 5 seconds later. This function can be used to

reset smoke detectors that are operated by an external power supply through a

Model 716 Output Expander Module. Enter 0 (zero) to disable this output.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

ouTPuT oPTionS

11.15

11.16

Closing Wait Output

Enter the output number to turn on for approximately four (4) seconds when Closing

Wait is programmed as YES and the panel successfully communicates the closing

message at arming. If the closing message does not communicate successfully, this

output does not turn on.

CLS WAIT OUT:

Arm-Alarm Output

Enter the output number to turn on steady when any area of the system is armed. If

an alarm occurs causing the keypads to turn Red, this output pulses and continues to

pulse for approximately ﬁve (5) minutes after the panel is disarmed. Enter 0 (zero)

to disable.

ARM-ALARM OUT: 0

Wireless Outputs

• The Arm-Alarm Output is compatible with the Model 1117 Wireless LED

Annunciator and the Model 1116 Wireless Relay Output connected to a Model

572 Indicator LED.

• When the Model 1117 is battery operated, the LED is off when the system is

armed to conserve battery life. If an alarm occurs, the output ﬂashes quickly.

• When using the Model 1116 connected to a Model 572, the LED is on when the

system is armed. If an alarm occurs, the output pulses.

• To operate the Arm-Alarm output within one second, program a fast response

number from 480 to 499. Fast response operation reduces overall wireless

output battery life.

• To operate the Arm-Alarm output within 15 seconds, program a slow response

number from 450 to 474. Slow response operation increases overall wireless

output battery life.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

ouTPuT informaTion

Output Information

12.1

12.2

Output Information

This section allows you to program wireless outputs and name wired outputs.

OUTPUT INFO

Output Number

Enter an output number. Entry range is 1 to 6, 450 to 474, 480 to 499, 500 to 999.

OUTPUT NO. X X X

12.3

Output Name

This section allows you to deﬁne a 32 character alphanumeric name for any output

numbers. The name can display on the keypad when a user performs the browser

feature at Outputs On/Off. See the XR100/XR500 User’s Guide (LT-0683CAN)

Appendix for browser operation.

OUTPUT NAME

12.4

12.5

Output Real-Time Status

OUTPUT REAL-TIME

Selecting YES allows Real-Time Status reports, such as Output ON, OFF, PULSE, or

TEMPORAL to be sent using PC Log reports. Selecting NO disables Real-Time Status

for this output device. Default is NO.

STATUS

NO YES

Serial Number

This option and the next option only display when the output number entered is for

a wireless output. Enter the eight-digit serial number found on the wireless device.

SERIAL#: XXXXXXXX

This message displays when the serial number is already programmed for another

output. The programmed output number displays.

ALREADY IN USE

OUTPUT NO: XXX

12.6

Supervision Time

Press any top row key to select the supervision time required for the wireless

output. Press COMMAND to accept the default time. Default is 240 minutes.

SUPRVSN TIME: 240

Note: Refer to the Wireless Check-in and Supervision Time Deﬁnitions section of the

Appendix for supervision information.

Press the Select key under the required number of minutes. The wireless output

must check in at least once during this time or a missing condition is indicated for

that output. Zero (0) indicates an unsupervised transmitter.

SELECT MINUTES:

240

Note: When the panel is reset, a receiver is installed or powered down and powered

up, or programming is complete, the supervision timer restarts for all wireless

outputs.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

ouTPuT grouPS

Output Groups

OUTPUT GROUPS

13.1

Output Groups

This function allows you to assign outputs to groups. Output groups can be assigned

to other areas of programming such as Output Options or Alarm Action of Zone

Information, just like single outputs are assigned. This allows the entire group of

outputs to turn on and off as required by the programming option.

GROUP NO: -

13.2

13.3

Group Number

Enter a group number from 1 to 20. Up to 20 different groups may be assigned.

GROUP NAME X X

Group Name

The group name displays. To change the default name, press any top row Select key

then enter up to 32 characters for the group name. Press COMMAND to enter the

outputs to be assigned to the group.

OUTPUT NO 1:

OUTPUT NO 2:

OUTPUT NO 3:

OUTPUT NO 4:

OUTPUT NO 5:

OUTPUT NO 6:

OUTPUT NO 7:

OUTPUT NO 8:

13.4

Output Number

Enter the Output number. Entry range is 1 to 6, 450 to 474, 480 to 499, 500 to 999

(outputs), D1 to D16 (doors), and G1 to G20 (groups). The maximum number of

outputs that can be assigned to a speciﬁc group is eight.

An output group may be assigned as one of the output numbers in another output

group.

Example: Output Group 1 consists of only four assigned outputs. Output Group

1 could be assigned as one output in Output Group 2. Output Group 2 could still

have 7 other outputs assigned to that group. When Output Group 2 is turned on, 11

outputs could be turned on. This allows Output Groups to be assigned within other

Output Groups providing many combinations.

Output groups 1 to 10 can be assigned by a user proﬁle for applications such as

elevator control. See the XR500 User’s Guide (LT-0683CAN) Output Group section for

additional information.

Output groups 11 to 20 cannot be assigned to a proﬁle and are available for

installation applications such as special lighting, etc. To assign these groups to a

proﬁle, use Remote Link™ or System Link™ software from DMP.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

menu diSPlay

Menu Display

14.1

MENU DISPLAY

Menu Display

Menu Display allows you to select at which keypad addresses the user can access the

following functions.

To select a keypad, enter the device number (keypad address) using the digit keys

on the keypad. When a keypad is selected, an asterisk appears next to the keypad

address. Enter the number again to deselect the keypad. Press the COMMAND key

to display the next set of keypads (9 through 16). Refer to the Multiple Displays

section at the beginning of this document.

14.2

ARMED STATUS:

Armed Status

Enter the keypad addresses (1 through 16) that show the armed areas. The User

Menu Armed Areas function also displays the custom area name you enter in Area

Information.

When only areas one to eight are used, the Armed Status display is 1 2 3 4 5 6 7 8.

When areas nine or higher are used the system Armed Status display reads ALL

SYSTEM ON or SYSTEM ON. Press the COMMAND key to display additional areas.

Refer to the Multiple Displays section at the beginning of this document and in the

XR500 User’s Guide (LT-0683CAN).

14.3

14.4

TIME DISPLAY:

Time

Enter the keypad addresses that can display the time and day of the week.

ARM/DIS DISPLAY:

Arm/Disarm

Enter the keypad addresses from which users can arm and disarm areas.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

STaTuS liST

Status List

15.1

STATUS LIST

Status List

This function allows you to select the zone alarms and troubles, and system monitor

troubles displayed at the keypads. The Status List function operates automatically

when the keypad is not performing any other function.

The keypad stays in the Status List until the user arms or disarms or selects a menu

option. Status List alternates with the Armed Status on keypad addresses selected

in the Menu Display - Armed Status section. You can choose to have System Monitor

troubles placed in the list, the different zone types placed in the list, and at which

keypad addresses they display.

To select a keypad, enter the device number (keypad address) using the digit keys

on the keypad. When a keypad is selected, an asterisk appears next to the keypad

address. Enter the number again to deselect the keypad. Press the COMMAND key

to display the next set of keypads (9 through 16). Refer to the Multiple Displays

section at the beginning of this document.

15.2

15.3

DISPLAY KEYPADS:

Display Keypads

This option deﬁnes which keypad addresses display the various status information.

Any combination of addresses can be entered to display the status items that follow.

If you do not want a particular status item to display, do not enter any addresses.

SYSTEM TROUBLES: System Monitor Troubles

Speciﬁes the keypad addresses (1 through 16) where any trouble on a System Monitor

displays. The System Monitors include the following:

•

AC Power

Battery Power

Closing Check

Panel Box Tamper

Phone Line 1

Phone Line 2

Wireless Receiver Trouble

Wireless Jamming Trouble or Alarm

(requires the 893A Dual Phone Line Module)

The System Monitor name is placed in the Status List and the keypad steady trouble

buzzer sounds. The buzzer remains on until any keypad top row Select key is

pressed. The name remains in the list until the condition is restored. The buzzer

sounds at 10:00 am daily until the system trouble is cleared from the Status List.

15.4

FIRE ZONES:

Fire Zones

Speciﬁes the keypad addresses (1 through 16) where all ﬁre zone alarms and troubles

display. The zone name displays and, if it is a trouble condition, the keypad steady

trouble buzzer sounds. The buzzer remains on until any top row Select key is

pressed and a user code is entered. If a trouble condition remains in the display, the

buzzer sounds at 10:00 am daily until the trouble is cleared from the Status List.

When using LCD Keypads, the panel provides distinct speaker tones from the keypad

for Fire:

On - Fire zone alarm and Bell Output or Fire Bell Output is ON.

Off - Alarm Silence

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

STaTuS liST

15.5

Burglary Zones

BURGLARY ZONES:

Speciﬁes the keypad addresses (1 through 16) where all burglary zone alarms and

troubles display. Burglary zones include Night, Day, and Exit type zones. Burglary

zone troubles remain in the list until the zone restores. All keypads are selected by

default.

For zone alarms, only the last burglary zone tripped remains in the list. The alarm

remains in the list until another burglary zone goes into alarm, any area of the

system is disarmed, or 10 minutes elapse without an alarm. This ensures that if a

burglary is in progress the last zone tripped remains in the list even if the zone is

restored.

The keypad buzzer sounds for one second on burglary alarms.

When using LCD Keypads, the panel provides distinct speaker tones from the keypad

for Burglary:

On - Burglary zone alarm and Bell Output or Burglary Bell Output is ON.

Off - Alarm Silence.

You can further deﬁne which keypad address shows a Burglary Zone event by

entering that area number in the Display Areas menu during Device Setup.

15.6

SPRVISORY ZONES:

PANIC ZONES:

Supervisory Zones

Speciﬁes the keypad addresses (1 through 16) where all supervisory zone alarms

and troubles display. Supervisory zones are entered in the status list and sound the

keypad buzzer until a valid user code is entered at any keypad address. If a trouble

condition remains in the display, the buzzer sounds at 10:00 am daily until the

supervisory trouble is cleared from the Status List.

15.7

15.8

15.9

Panic Zones

Speciﬁes the keypad addresses (1 through 16) where all panic zone alarms and

troubles display. The name of the zone remains in the list until the zone restores.

The keypad buzzer does not sound for panic alarms or troubles.

EMERGENCY ZONES: Emergency Zones

Speciﬁes the keypad addresses (1 through 16) where all emergency zone alarms and

troubles display. The name of the zone remains in the list until the zone restores.

The keypad buzzer does not sound for emergency alarms or troubles.

AUX 1 ZONES:

Auxiliary 1 Zones

Speciﬁes the keypad addresses (1 through 16) where all Auxiliary 1 zone alarms and

troubles display. The name of the zone remains in the list until the zone restores.

The keypad buzzer does not sound for Auxiliary 1 alarms or troubles.

You can further deﬁne which keypad address shows an Auxiliary 1 Zone event by

entering that area number in the Display Areas menu during Device Setup.

15.10 AUX 2 ZONES:

Auxiliary 2 Zones

Speciﬁes the keypad addresses (1 through 16) where all Auxiliary 2 zone alarms and

troubles display. The name of the zone remains in the list until the zone restores.

The keypad buzzer does not sound for Auxiliary 2 alarms or troubles.

You can further deﬁne which keypad address shows an Auxiliary 2 Zone event by

entering that area number in the Display Areas menu during Device Setup.

15.11

Communication Trouble

Speciﬁes when communication troubles are displayed on keypads that are

programmed to display System Monitor Troubles. Default is NO.

COMM PATH TRBL:

ALL NO YES

Select YES to display communication trouble when any communication path fails.

Select ALL to display communication trouble only when all paths have failed.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

PrinTer rePorTS

Printer Reports

16.1

PRINTER REPORTS Printer Reports

This section allows you to deﬁne the operation of a local printer connected to the

panel through the use of a DMP 462P Printer Interface Card. The 462P allows you to

connect the DMP SCS-PTR or other compatible 40-character or 80-character serial

printer to the panel.

Printing the panel event buffer

The Display Events option in the User Menu contains a PRINT command that allows

the user to send the contents of the panel event buffer to a local printer. The PRINT

option is visible whether or not a 462P Printer Interface Card is attached to the

panel.

16.2

16.3

ARM/DIS NO YES Arm and Disarm Reports

Prints arming, disarming, and Late to Close reports. Includes the area number,

name, and action (armed, disarmed, or late), the user number, user name, and time

and date.

ZONE

NO YES Zone Reports

Prints changes in the active zones status. Includes the zone number, name, and type

as well as the action (alarm, trouble, bypass, etc.) user number (if applicable) and

area name. When the Walk Test or Panic Zone Test is performed, Verify and Fail

messages also print for each zone.

16.4

USR CMDS NO YES User Command Reports

Prints user code changes, outputs turned ON or OFF (if operated by a schedule, SCH

is shown in Display Events in place of the user number), schedule changes, and User

Menu functions.

16.5

16.6

DOOR ACS NO YES Door Access Reports

Prints door access activity. Includes the door number, ﬁrst and second user number,

ﬁrst and second user name, and the time and date of the door access.

SUPV MSG NO YES Supervisory Reports

Prints System Monitor Troubles and system events. See Status List - System Monitor

Troubles.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

PC log rePorTS

PC Log Reports

17.1

PC LOG REPORTS PC Log Reports

This section allows you to program the types of PC Log Reports the panel sends

through the 462N Network Interface Card or through the J21 Serial Connector

directly on the XR500 Series Canadian panel. The reports include information such

as the type of activity, time and date of the activity, and user name and number.

These data reports can be accessed from a PC using the Advanced Reporting Module.

See the Installation Guide (LT-0681CAN) for detailed J21 setup information or the

User’s Guide (LT-0683CAN) for more information.

Note: The network connection that sends PC Log Reports is not monitored for

network trouble. The PC Log Reports option should NOT replace the primary

communication method or act as a backup communication method.

If there is trouble with the network connection, the panel continues to attempt to

send the PC Log Reports until the connection is reestablished. The panel then sends

the reports. A Network Trouble message is NOT sent if the connection is lost since

this report tool is not designed to be monitored by a receiver. The PC Log Reports

have the lowest priority of panel reports sent.

For information about the 462N card capabilities with PC Log Reports and Network

Communication method, see 462N Card Examples in the Appendix.

Note: The PC Log Address String entered CANNOT be the same as that entered in

Communication.

COMM TYPE: NONE

17.2

17.3

Communication Type

Select the Communication Type to send the PC Log Reports. Default is NONE.

NONE NET 232

Net IP Address

NET IP ADDRESS

This option displays when the Communication Type for PC Log Reports is NET. Enter

the IP address containing up to 16 characters. The Net IP Address must be unique and

cannot be duplicated on the network. Enter all 12 digits and leave out the periods.

For example, enter IP address 192.168.0.250 as 192168000250. The periods display

automatically.

NET PORT 2001

17.4

17.5

Net Port

This option displays when Communication Type for PC Log Reports is Net. Enter the

Port number. Valid numbers are from 0 to 65535. Default is 2001.

232 COMM PORT:

232 Communication Port

This option displays when Communication Type for PC Log Reports is 232. To enable

PC Log Reports, select either the on-board connector (O) or select A, B, C, D or E for

the corresponding slot in use on the DMP Model 462N Network Interface card. The

slots are labeled from left to right, beginning with A. Default is O.

Set the XR500 Series panel J23 jumper to R and brieﬂy reset the panel using the J16

jumper to activate RS-232 operation.

17.6

17.7

17.8

232 SETUP:

232 Setup

This option displays when Communication Type for PC Log Reports is 232. Enter up

to 32 characters.

ARM/DIS NO YES Arm and Disarm Reports

Sends arming, disarming and Late to Close events. Includes the area number, name

and action, the user number and name, and the time and date.

ZONE

NO YES Zone Reports

Sends changes in the status of active zones. Includes the zone number, name, type,

the action (alarm, trouble, bypass, etc.), user number (if applicable), and area

name. For a Walk Test, Verify and Fail messages are sent for each zone.

17.9

USR CMDS NO YES User Command Reports

Sends user code changes, schedule changes, and door access denied events.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

PC log rePorTS

17.10 DOOR ACS NO YES Door Access Reports

Sends door access activity: door number, user number and name, and time and date.

17.11 SUPV MSG NO YES Supervisory Reports

Sends system monitor reports, such as AC and battery, and system event reports.

Supervisory Reports also sends the following reports:

• Abort

• Exit Error

• Ambush

• System Recently Armed

• *Late to Close

• Alarm Bell Silenced

• Unauthorized Entry

* Only sent as a Supervisory Report if Area Schedules is not enabled, Closing

Check is enabled, and an opening/closing schedule has been programmed.

Note: To send these reports to the PC Log, you must enable SUPV MSG.

17.12

PC Log Real-Time Status

Select YES to send Real-Time Status reports for zones, doors, and outputs. The

speciﬁc reports must also be selected by individual zone or output. The Real-Time

Status messages are sent to a PC running a graphic display software. Default is NO.

PC LOG REAL-TIME

STATUS NO YES

The messages that can be sent are:

•

Door Open with zone number

Door Closed with zone number

Door Open with door number

Door Closed with door number

Output On

Output Off

Output Pulse

Output Temporal

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

area informaTion

Area Information

18.1

AREA INFORMATION Area Information

Allows you to assign functions to the different areas in the system. All non-24-hour

zones must be assigned to an active area. See Zone Information.

You activate an area by assigning it a name. See Area Name. A name is given to

each active area in place of a number to assist the user during arming and disarming.

When only areas one to eight are used, the Armed Status display is 1 2 3 4 5 6 7 8.

When areas nine or higher are used the system Armed Status display reads ALL

SYSTEM ON or SYSTEM ON. Press the COMMAND key to display additional areas.

Refer to the Multiple Displays section at the beginning of this document and in the

XR500 User’s Guide (LT-0683CAN).

18.2

EXIT DELAY:

60 Exit Delay

Enter the exit delay time for all Exit type zones in this area. When the exit delay

time starts, all activity on that zone and other non-24-hour zone types in the area

is ignored until the exit delay expires. The keypad displays the Exit Delay time

countdown and annunciates the Exit Delay tone at 8 second intervals until the last

10 seconds when annunciation is at 3 second intervals.

The exit delay can be from 30 to 250 seconds. Default is 60 seconds.

During Exit Delay, if an exit zone trips, then restores, and trips again, the Exit Delay

timer restarts. This restart can occur only once. The Exit Delay restart is disabled

when programmed for High Line Security operation.

Exit Error Operation: At arming, when an entry/exit zone (EX) is faulted at the end

of the exit delay then one of two sequences occur:

For Entry Delay 1 EX type zones:

• the bell sounds for the length of time set in Bell Cutoff programming.

• the Entry Delay operation starts requiring code entry to disarm

• if not disarmed, a zone alarm and an exit error are sent to the receiver.

For Entry Delay 2-4 EX type zones:

• the zone is force armed and a zone force arm message is sent to the receiver

• an Exit Error is sent to the receiver

• the bell sounds for the length of time set in Bell Cutoff programming

18.3

18.4

BURG BELL OUT:

Burglary Bell Output

Enter the output number (0 to 6, 500 to 999, G1 to G20, or D1 to D16) that is turned

on any time a Burglary type zone is placed in alarm. The output is turned off when

you disarm any area and no other Burglary type zones are in alarm. The output can

also be turned off using the Alarm Silence option in the User Menu or by entering

a user code with the authority to silence alarms. The duration of this bell output

follows the time entered in the System Options>Bell Cutoff Time prompt. See the

Output Options - Bell Cutoff Time section. If Bell Test is selected YES, the Burglary

Bell Output entered here is turned on for two seconds each time the system is

armed.

Opening/Closing Reports

This option allows an Opening report to be sent to the receiver whenever any area is

disarmed. A Closing report is also sent to the receiver when any area is armed.

O/C RPTS NO YES

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

area informaTion

18.5

CLS CHK

NO YES Closing Check

Select YES to enable the panel to verify that all areas in the system are armed

after permanent or extended schedules expire. If the Closing Check ﬁnds any areas

disarmed past the scheduled time, the keypads selected to display System Trouble

Status displays CLOSING TIME! and emits a steady beep. When Area Schedules is set

to YES in Area Information, the speciﬁc area and name display followed by — LATE.

When Auto Arm is NO, if within ten minutes the system is not armed or if the

schedule is not extended, a Late to Close report is sent to the SCS-1R Receiver.

When Auto Arm is YES, the area arms. See Automatic Arming section.

If the area becomes disarmed outside of any schedule, the Closing Check sequence

occurs after the Late Arm Delay time. See Late Arm Delay.

When Closing Check is NO and Auto Arm is YES, the system immediately arms when

the schedule expires. No warning tone occurs.

In addition, when Closing Check is NO, the option to extend a schedule does not

display when the schedule expires.

18.6

18.7

CLS CODE NO YES Closing Code

When YES is selected, a code number is required for system arming. If NO is

selected, a code number is not required for system arming.

ANY BYPS NO YES Any Bypass

When YES is selected, zones can be bypassed without a code number during the

arming sequence. A code number is always required to use the Bypass Zones option

from the menu.

18.8

18.9

AREA SCH NO YES Area Schedules

Select YES to allow each area to set its own shift schedules 1 to 4. Enter NO to

provide one set of schedules for this system.

Note: Area Schedules are not designed to operate with All/Perimeter or Home/

Sleep/Away systems.

EARLY AMBUSH:

Early Morning Ambush (XR500N/XR500E only)

Enter the number of minutes (1 to 15) before a silent alarm (Early Morning Ambush S33)

is sent to the central station using the area 1 account number. Enter 0 (zero) to disable

this option.

When a user code is entered to disarm area 1 at a keypad or reader with Access

Areas assigned to area 1, the same or different user code must be entered within the

programmed number of minutes to prevent an ambush message from being sent to

the receiver. The second user code also must have authority to disarm area 1.

In addition, a zone activation with Alarm Action Message C also cancels the Early

Morning Ambush timer and stops an Ambush message from being sent to the receiver.

See Report to Transmit section in Zone Information.

The keypad does not display any indication that the ambush timer is running.

Indications can be provided by assigning an output number to Entry Out and Ambush

Out in Output Options. Entry Out turns on one minute before the timer expires and

turns off at expiration. Ambush Out turns on at the timers’ expiration and turns off

when Sensor reset is performed.

18.10

AREA NO: -

Area Number

Enter the number of the area to program. After entering the area number, press

COMMAND to enter the area name. Only Area systems allow the area name to be

changed.

Note: When All/Perimeter or Home/Sleep/Away is selected as the system type, the

Area Number does not display.

18.10.1

All/Perimeter Programming

When All/Perimeter is selected as the system type, program the Interior and

Perimeter areas as needed.

INT

PERIM

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

area informaTion

18.10.2

Home/Sleep/Away Programming

When Home/Sleep/Away is selected as the system type, program the Interior,

INT BDRM PERIM

* UNUSED *

Bedroom, and Perimeter areas as needed.

18.11

Area Name

The area name can be up to 32 alphanumeric characters. To add an area name to the

system, press any Select key and then enter up to 32 characters for the new area name.

Press COMMAND to continue. For instructions on entering alphanumeric characters see

section 1.7 Entering Alpha Characters. Inactive areas are marked * UNUSED *. Only

systems programmed for Area arming have the option available to change the area name.

To mark an active area unused, press any top row Select key to delete the old name,

then press the COMMAND key. The programmer automatically programs the name

as *UNUSED*. If you have already cleared Area Information during Initialization, all

areas are marked * UNUSED *. See Initialization section.

Home/Sleep/Away with Guest systems display the area name, but the names cannot

be changed. The following are the display names that appear on the keypad:

Area Display

Perimeter

Guest1 Perimeter

Guest2 Perimeter

Interior

Guest1 Interior

Guest2 Interior

Bedrooms

Guest1 Bedrooms

Guest2 Bedrooms

18.12 ACCOUNT NO: 12345 Account Number

Enter the account number to be sent to the receiver for this area. Choose an account

number compatible with the Communication Type selected in Communications. The

default Account Number is the one previously entered in Communications. This

account number is used when sending area messages and events to the central station

See the Area Account Number Messages in the Appendix.

18.13 AUTO ARM NO YES Automatic Arming

Select YES to allow this area to arm automatically according to permanent, temporary,

or extended schedules. If no schedules are programmed, the area auto arms every hour.

If closing check is selected as YES, the automatic arming function does not take

place until the expiration of a ten minute Closing Check delay. See Closing Check.

If the area has been disarmed outside of any permanent or temporary schedule, the

closing check sequence occurs one hour after the area is disarmed.

At arming, bad zones are handled according to the option selected in section Bad

Zones. If a closing report is sent, the user number is indicated as SCH on the SCS-1R

Receiver. NO disables automatic arming for this area.

18.14 BAD ZONES:

BYP Bad Zones

At the time of automatic arming, some zones in the area may not be in a normal

condition. This option allows you to program the panel response to these bad zones.

This option does not display if AUTO ARM is NO.

BYP - All bad zones are bypassed. A report of the bypass is sent to the receiver if

REF

BYP FORC

Bypass Reports is YES. The report indicates SCH as the user number.

FORC - All bad zones are force armed. Zones force armed in a bad condition are

capable of restoring and reporting an alarm if tripped. A forced zone report is

transmitted if Bypass Reports is YES. The report indicates SCH as the user number.

REF - The automatic arming is refused and no arming takes place. A No Closing

report is sent to the receiver regardless of the Closing Check selection.

18.15 AUTO DIS NO YES Automatic Disarming

NO disables automatic disarming by schedule for this area. When YES is selected,

the area automatically disarms according to permanent or temporary schedules. If

an opening report is sent to the receiver, the user number is indicated as SCH.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

area informaTion

18.16

Armed Output Number

ARMED OUTPUT:

Enter the output to turn on when this area is armed. If an exit delay is used for this

area, the Armed Output turns on at the start of the exit delay. The output is turned

off when this area is disarmed. The output cannot be turned on from the User Menu

Outputs On/Off option.

18.17 LATE OUTPUT:

Late Output Number

Enter the output to turn on when this area is not armed by its scheduled time and

Area Late or Closing Time displays at a keypad and the keypad buzzer is on. The

output is turned off when the keypad buzzer is silenced by pressing any key. Default

is 0 (zero).

18.18 LATE/ARM DLY: 60 Late Arm Delay

Enter 4 to 250 minutes to delay before automatic re-arming occurs after the area

becomes disarmed outside of schedules. See Closing Check. Default is 60 minutes.

Note: The Late Arm Delay can be superseded by the Re Arm Delay setting of the

User Proﬁle assigned to the user who disarmed the area. Refer to the Re Arm Delay

section in the XR500 Series Canadian User’s Guide (LT-0683CAN).

18.19 BANK/SAF NO YES Bank Safe & Vault (XR500N/XR500E only)

NO disables the Bank Safe & Vault feature for this area. When selected as YES,

schedules set for this area and the time of day cannot be changed while the area is

armed.

Program schedules before arming: A Bank Safe & Vault area can only be disarmed

during scheduled times. If the area becomes armed before programming a schedule,

the panel must be reset before the area can be disarmed from a keypad or the Bank

Safe & Vault option in Area Information must be set to NO.

Zones assigned to Bank Safe & Vault areas cannot be bypassed or force armed. Do

not assign Bank Safe & Vault area to an Arming zone. Arming zones can disarm Bank

Safe & Vault areas outside of a schedule.

18.20 COMMON NO YES Common Area

Select YES to enable this area to operate as a common area. This area is armed

when the last area in the system is armed and is disarmed when the ﬁrst area in the

system is disarmed. You can have multiple common areas in each system. For the

common area to work properly, do not assign the common area to any user code.

When a user code can arm and disarm the common area from a keypad at any time,

the common area does not function as a common area.

18.21 ARM FIRST NO YES Arm First Area

Select YES to enable this area to operate as an Arm First area. This area is

automatically armed when any non-Arm First area assigned to the same keypad is

armed but does not disarm when other areas become disarmed. Assign areas to

keypads using the Display Areas option in Device Setup programming. You can have

multiple Arm First areas in a system and divide them among keypads if needed. If

an Arm First area has faulted zones that cannot be bypassed, arming stops and the

areas are not armed. Correct the problem with the Arm First area and then begin

the arming process again. Default value is NO.

Note: The Arm First automatic arming only occurs when arming from a keypad.

Arming from a zone, schedule, or remotely is not affected and Arm First areas do not

automatically arm.

18.22 TWO MAN NO YES Two Man Rule (XR500N/XR500E only)

Select YES to require two user code entries to disarm and/or allow door access to

this area. When a user presents a code to a keypad or reader requesting a door

access or disarm, 2ND CODE displays and requires the entry of a different user code

with at least the same authority. The second user code must be entered within 30

seconds.

NO disables the Two Man Rule for this area.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

zone informaTion

Zone Information

19.1

ZONE INFORMATION Zone Information

Zone Information allows you to deﬁne the operation of each protection zone used in

the system. All protection zones, whether located on a command processor panel,

Security Command keypad, or zone expander are programmed the same way.

19.2

ZONE NO: -

Zone Number

Enter the number of the zone you intend to program. Available zone numbers are

shown in the table below. The keypad zone numbers begin with the keypad address

and are followed by the particular zone from that keypad. For example, a 7073 at

keypad address 7 would provide zones 71, 72, 73, and 74.

Press COMMAND to enter a zone name.

Address

Programming Zone Number

Panel

1-10

11-14

21-24

31-34

41-44

51-54

61-64

71-74

81-84

91-94

101-104

111-114

121-124

131-134

141-144

151-154

161-164

400-449

500-599

600-699

700-799

800-899

900-999

1100 Series Key Fob

LX-Bus 1 (A)

LX-Bus 2 (B)

LX-Bus 3 (C)

LX-Bus 4 (D)

LX-Bus 5 (E)

Note: For 1100 Series Key Fob zones (400-449), programming continues at the 1100

Series Key Fobs Section.

19.3

* UNUSED *

Zone Name

Zone names can have up to 32 alphanumeric characters. A name must be given to

each zone in the system. The name can display at the keypads during arming and

disarming so the user does not have to memorize zone numbers. Users can asso-

ciate a zone name with a particular protection point. A zone that is not part of the

system must be marked unused.

To add a zone name to the system, press any Select key and then enter up to 32

characters for the new zone name. Press COMMAND to continue.

To mark a zone unused, delete the old name by pressing a top row Select key, then

press the COMMAND key. The programmer automatically programs the name as

* UNUSED *. If you have already cleared Zone Information during Initialization, the

zones is marked * UNUSED *.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

zone informaTion

19.4

Zone Type

ZONE TYPE: BLANK

The Zone Type deﬁnes the panel response to the zone being opened or shorted.

This is called the Alarm Action. There are up to 13 possible alarm action responses

depending on the zone type and any restrictions it may have. See the Zone Type

chart in the Appendix.

When you assign a Zone Type to a zone, automatic zone responses are made. There

are 12 Zone Types to choose from. Application descriptions for each zone type can

be found in the Appendix of this manual.

To enter a new Zone Type, press any Select key. The display lists all of the available

Zone Types four at a time.

Blank, Night, Day, or Exit. Press COMMAND for additional zone types.

- -

NT DY

PN EM SV Fire, Panic, Emergency, or Supervisory. Press COMMAND for additional zone types.

A2 FV AR Auxiliary 1, Auxiliary 2, Fire Verify, or Arming (keyswitch). Press COMMAND for

additional zone types.

If you select Blank, Night, Day, Exit, Auxiliary 1, Auxiliary 2, or Arming as the Zone

Type, the zone must be assigned to an active area. If you select Fire, Fire Verify,

Panic, Emergency, or Supervisory as the Zone Type, it is a 24-hour zone that is always

armed and no area assignment is needed.

Zone Type Speciﬁcations

The panel contains 12 default zone types for use in conﬁguring the system. These zone

types provide the most commonly selected functions for their applications. All zone

types except the Arming zone type can be customized by changing the options listed

below. Arming zone type programming continues at Arming Zone Area Assignment.

Refer to the Appendix for complete zone type descriptions.

19.5

Area Assignment

Enter the area number where the Night, Day, Exit, Auxiliary 1, or Auxiliary 2 zone

is being assigned. For an Area system, area numbers 1-32 can be assigned. For a

Home/Sleep/Away with Guest system, area numbers 1-9 can be assigned.

AREA NO: -

In an All/Perimeter or Home/Sleep/Away system, the currently selected area,

Perimeter, Interior, Bedroom displays.

AREA:

INT

PERIMETER

On an All/Perimeter system, select INT to program zones for the interior area and

select PERIM to program zones for the perimeter area.

PERIM

On a Home/Sleep/Away system, select INT to program zones for the interior area,

select BDRM to program zones for the bedroom area, and select PERIM to program

zones for the perimeter area.

INT BDRM PERIM

19.6

Fire Bell Output

This output (1 to 6, 500 to 999, G1 to G20, or D1 to D16) is turned on any time a

Fire, Fire Verify, or Supervisory zone is placed in alarm. The output is turned off by

any the following actions:

FIRE BELL OUT:

• When the User Menu Alarm Silence function is performed.

• When a valid user code is entered to silence the bell.

• When the Silence key is pressed on the 630F Remote Fire Command Center.

• Using the Outputs On/Off function in the User Menu.

• The expiration of the Bell Cutoff time.

This output can be connected to a lamp, LED, or buzzer using the DMP Model 716

Output Expansion Module.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

zone informaTion

19.7

Arming Zone Area Assignment

In an Area or Home/Sleep/Away with Guest system, if the zone has been

programmed as an Arming Type (AR), enter the areas that the zone controls.

ARM/DIS AREAS

When the zone changes from normal to shorted, the programmed areas toggle between

the armed or disarmed condition using the Style programming below. When restored to

normal, no action occurs. When the zone is opened from a normal (disarmed) state, a

trouble is reported. When opened from a shorted (armed) state, an alarm is reported

and the zone is disabled until you disarm the area(s) from either a keypad or Remote

Link™ computer.

To visually indicate the armed state of the area(s), you can assign an Armed Output

to individual areas and use remote LEDs at the keyswitch. The LED turns on or off to

indicate to the user the armed state of the area(s).

In an All/Perimeter or Home/Sleep/Away system, this option speciﬁes the areas to

be armed by the Arming Type zone. For All/Perimeter systems, choose PERIM or ALL,

for Home/Sleep/Away or Home/Away systems, choose HOME, SLEEP, or AWAY.

ARM AREAS: PERIM

Perimeter/All - Specify whether the arming zone arms just the Perimeter (PERIM) or

the Perimeter and Interior areas (ALL) for All/Perimeter systems. When disarming,

all areas are disarmed.

PERIM

ALL

Home/Sleep/Away - Specify whether the arming zone arms the Perimeter (HOME),

the Perimeter and Interior (SLEEP), or all three areas (AWAY). When disarming, all

areas are disarmed.

HOME SLEEP AWAY

Arming Zone Operation

If any bad zones are present when the Arming zone is shorted, the LED delays

lighting for 5 seconds. If during the 5-second delay the Arming zone is shorted

again no arming takes place. If 5 seconds expire without the zone shorting again

or restoring to normal, the areas arm and bad zones are force armed. To allow bad

zones to be force armed, the Any Bypass option must be set to YES. If Any Bypass

option is set to NO, arming does not occur. See the Area Information - Any Bypass

section. A priority zone cannot be force armed.

19.8

Style

STYLE:

This option speciﬁes the style for the arming/disarming operation. The default style

is TGL (toggle). Press any Select key to display the STYLE options. To view more

style options press the COMMAND key.

TGL ARM DIS STEP TGL (Toggle) - When the zone changes from normal to shorted, the programmed

areas toggle between the armed or disarmed condition. When restored to normal,

no action occurs. When the zone opens from a normal (disarmed) state, a trouble is

reported. When opened from a shorted (armed) state, an alarm is reported and the

zone is disabled until you disarm the area(s) from either a keypad or Remote Link.

ARM - When the zone is shorted, the programmed areas are armed. When restored to

normal, no action occurs. When the zone is opened from a normal (disarmed) state, a

trouble is reported. When opened from a shorted (armed) state, an alarm is reported.

DIS (Disarm) - When programmed, a short disarms the programmed areas. When

restored to normal, no action occurs. When the zone is opened from a normal

(disarmed) state, a trouble is reported.

STEP - A short arms the areas and beeps the keypads once. A normal condition

causes no action. An open condition disarms the programmed areas and beep the

keypads for one second.

Note: This arming style is designed for wireless arming pendants. When using an

arming/disarming keyswitch locate the keyswitch within the protected area.

MNT

MNT (Maintain) - When the zone is shorted, the programmed areas are armed.

When restored to normal, the programmed areas are disarmed and any alarm bells

are silenced. When the zone is opened from a normal (disarmed) state, a trouble

is reported. If opened from a shorted (armed) state, an alarm is reported and the

zone is disabled until you disarm the area(s) from either a keypad or Remote Link.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

zone informaTion

19.9

NEXT ZN? NO YES Next Zone

Select YES to terminate zone programming. The display returns to Zone Number,

allowing you to enter a new zone number. Select NO to make alterations to the

Alarm Action for a zone. Alarm Action is deﬁned beginning with section 16.12.

To program zones for wireless operation, select NO at the NEXT ZONE - NO YES

option. The WIRELESS NO YES option displays. If the zone you are programming

is intended for wireless devices, select YES. Select NO to continue programming

non-wireless zones in the 500 to 999 range.

• Zones 400 to 449 can be programmed for 1100 Series Key Fobs.

• Zones 500 to 699 can be programmed for FA Series Wireless.

• Zones 500 through 999 can be programmed for DMP 1100 Series Wireless.

DMP Wireless

For a DMP 1100X Wireless Receiver set the House Code from 1 to 50. See House Code programming

in System Options. Zones 500 through 999 can be programmed as Wireless zones. Set the XR500 Series

Canadian panel J23 jumper to X to enable on-board DMP Wireless operation. Brieﬂy reset the panel using

the J16 jumper to activate Wireless operation. Refer to the XR500 Series Canadian Installation Guide

(LT-0681).

For an 1100 Series Key Fob see section 19.11.

For an FA Series Remote Wireless Receiver see section 19.12.

NOTE: All wireless programming is stored in the XR500 Series Canadian panel. The 1100X Wireless

Receiver obtains the necessary programming information from the panel each time the receiver powers

up, when the programmer STOP routine is selected or the panel is reset. The receiver memory refresh

takes up to 10 seconds to complete depending on the number of wireless zones programmed and the Red

LED remains on during this time. Normal receiver operation is inhibited during the memory refresh period.

ZONE INFORMATION

WIRELESS? NO YES

19.10

Wireless

Select YES to program this zone as a DMP wireless zone. You must program

the wireless House Code prior to adding DMP wireless zones to the system. See

House Code programming in System Options. Default is NO.

19.10.1

Serial Number Entry

TRANSMITTER

SERIAL#: XXXXXXXX Enter the eight-digit serial number found on the wireless device.

This message displays when the serial number is already programmed for

another zone. The programmed zone number displays.

ALREADY IN USE

ZONE NUMBER: XXX

19.10.2

Contact

TRANSMITTER

CONTACT:XXXXXXXX

This option displays if the serial number entered is for an 1101 or 1103 Universal

Transmitter or 1114 Wireless Four-Zone Expander. Press any top row key to

select the contact.

This option displays when programming an 1101 or 1103 Transmitter. Select INT

to use the internal reed switch contacts. Select EXT to connect an external

device to the 1101 or 1103 terminal block. Default is INTERNAL.

TRANSMTR CONTACT

INT EXT

By allowing both of the Model 1101 or 1103 transmitter contacts (INT and

EXT) to be used at the same time, two zones may be programmed from

one transmitter. When using both contacts, you must use consecutive zone

numbers. Zones 531 and 532 or zones 890 and 891 are acceptable zone

assignments.

For example, program transmitter serial number 01345678 as Zone 521 with

an INT contact type and Zone 522 with an EXT contact type. The same serial

number is used for both zones.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

zone informaTion

This option displays when programming the 1114 Wireless Four-Zone Expander

TRANSMTR CONTACT

with four input contacts. The same serial number is used for all four contacts.

Select the contact number to program. When using the contacts, you must use

consecutive zone numbers. Default is Contact 1.

For example, use serial number 08345678 to program Contact 1 for Zone 561,

Contact 2 for Zone 562, Contact 3 for zone 563, and Contact 4 for zone 564.

A tamper on the 1114 is transmitted as the zone number assigned to Contact 1.

This message displays when the Contact is already programmed for another

zone. The programmed zone number displays.

ALREADY IN USE

ZONE NUMBER: XXX

This option only displays when EXT is selected as the Contact type. For external

devices connected to the 1101 or 1103 terminal block, select NO to use normally

closed (N/C) contacts. Select YES to use normally open (N/O) contacts. Default

is NO.

ZONE INFORMATION

NORM OPN NO YES

19.10.3

Supervision Time

Press any top row key to select the supervision time required for the wireless

zone. Press COMMAND to accept the default time. Default is 240 minutes.

TRANSMITTER

SUPRVSN TIME: 240

Note: Refer to the Wireless Check-in and Supervision Time Deﬁnitions section

of the Appendix for supervision information.

Press the Select key under the required number of minutes. The transmitter

must check in at least once during this time or a missing condition is indicated

for that zone. 1100 Series transmitters automatically checkin based on the

supervision time selected for the wireless zone, no additional programming

is needed. If two zones share the same transmitter, the last programmed

supervision time is stored as the supervision time for both zones. Zero (0)

indicates an unsupervised transmitter.

SELECT MINUTES:

240

Note: When the panel is reset or a receiver is installed or powered down and

powered up, the supervision timer restarts for all wireless zones.

19.10.4

19.10.5

LED Operation

LED OPERATION

NO YES

Select YES to turn on an 1142 Hold-up transmitter LED during Panic or

Emergency operation. Select NO to turn the LED off during Panic or Emergency

operation. The LED always operates when the transmitter case is open and the

tamper is faulted. Default is YES.

Disarm/Disable

DISARM DISABLE

NO YES

Select YES to disable the zone tripped message (short) to the 1100X Series

Receiver from the 1126 PIR transmitter during the disarmed period. When

disabled, the 1126 only sends supervision, tamper and low battery messages

during the disarmed period to extend transmitter battery life. Select NO to

always send zone tripped messages in addition to supervision, tamper and low

battery. Default is YES.

19.10.6

19.10.7

PIR Pulse Count

WIRELESS PIR

Select the number of infrared pulses (2 or 4) the 1126 PIR should sense before

sending a short message to the 1100X Series Receiver. Default is 4.

PULSE COUNT: 4

PIR Sensitivity

Select the sensitivity setting for the 1126 PIR. Selecting LOW sets the 1126 to

operate at 75% sensitivity for installations in harsh environments. Selecting

HIGH sets the PIR to maximum sensitivity. Default is LOW.

WIRELESS PIR

SENSITIVITY:LOW

19.10.8

NEXT ZONE NO YES Next Zone

Select YES to return to the ZONE NO: - prompt to program a new zone. Select

NO to display the Alarm Action option.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

zone informaTion

1100 Series Key Fobs

For an 1100 Series Key Fob set the House Code from 1 to 50. See House Code programming in System

Options. Only zones 400 to 449 can be programmed as 1100 Series Key Fob zones. Refer to the 1100

Series Key Fob Programming Sheet (LT-0706) supplied with the 1100X Wireless Receiver and the 1100 Series

Key Fob Install Guide (LT-0703) as needed.

To operate arming and disarming properly, the Key Fob should be assigned to a User Number with

appropriate area assignments, however, the User Number does not have to exist at the time the Key

Fob is programmed. The Key Fob User Number can be added later by the User.

The following programming continues from the Zone Number section when zone 400-449 is selected.

19.11.1

Key Fob User Number

Enter the User Number (1-9999) used to identify the key fob user and their

arming and disarming authority. Default is blank.

KEY FOB USER

NUMBER: XXXX

Displays when the User Number entered does not exist in User Code

programming. The key fob can be added, but the user must eventually be

added to cause the key fob to operate.

USER XXXX

NOT IN USE

19.11.2

19.11.3

Key Fob Serial Number

TRANSMITTER

SERIAL#: XXXXXXXX Enter the eight-digit serial number found on the wireless device.

Key Fob Supervision Time

Press any top row key to select the supervision time required for the key fob

zone. Press COMMAND to accept the default time. Default is 0 for key fobs.

TRANSMITTER

SUPRVSN TIME: 0

Press the Select key under the required number of minutes. The key fob must

check in at least once during this time or a missing condition is indicated for

that zone. 1100 Series key fobs automatically checkin based on the supervision

time selected for the wireless zone, no additional programming is needed.

Zero (0) indicates an unsupervised transmitter.

SELECT MINUTES:

240

Note: When the panel is reset or a receiver is installed or powered down and

powered up, the supervision timer restarts for all wireless zones.

19.11.4

19.11.5

Number of Key Fob Buttons

NO. OF KEY FOB

BUTTONS: X

Enter the number of buttons (1, 2, or 4) on the key fob being programmed.

Note: If the key fob is a one-button model, programming continues at the

Button Action section. Default button assignment for one-button key fobs is a

Panic Alarm (PN) with no output assigned.

Key Fob Button Selection (Four Buttons)

This prompt only displays if the key fob being programmed is a four-button

model. Press the Select key under the key fob button to program. The

following list identiﬁes the default button assignments:

TOP Arming with no areas assigned

BUTTON:

TOP BTM LFT RGT

BTM Disarming with no areas assigned

LFT Panic Alarm (PN) with no output assigned

RGT Arming with Area 1 assigned

19.11.6

Key Fob Button Selection (Two Buttons)

This prompt only displays if the key fob being programmed is a two-button

model. Press the Select key under the key fob button to program. The

following list identiﬁes the default button assignments:

TOP Arming with no areas assigned

BUTTON:

TOP BTM

BTM Disarming with no areas assigned

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

zone informaTion

19.11.7

Button Action

BUTTON ACTION

This option speciﬁes the Button Action for an individual key fob button. The

default action for the button selected is displayed. Press any Select key to

display the Button Action options. To view more options press COMMAND.

yyy = the name of the button being programmed (TOP, BTM, LFT, RGT).

yyy:

XXXXXXXX

ARM (Arm) - Arms selected areas and force arms bad zones.

DIS (Disarm) - Disarms selected areas.

BUTTON ACTION

ARM DIS TGL STA

TGL (Toggle Arm) - Toggles arm/disarm for selected areas and force arms bad

zones when arming.

STA (Status) - Causes the key fob LED to indicate the arm/disarm status of the

system.

PN (Panic) - Triggers a Panic zone type alarm with no restoral.

BUTTON ACTION

PN PN2 EM EM2

PN2 (Panic 2) - Triggers a Panic zone type alarm with no restoral when pressed

simultaneously with any other Panic 2 button. No action occurs when pressed

alone.

EM (Emerg) - Triggers an Emergency zone type alarm with no restoral.

EM2 (Emerg 2) - Triggers an Emergency zone type alarm with no restoral when

pressed simultaneously with any other Emergency 2 button. No action occurs

when pressed alone.

OUT (Output) - Causes an output to turn on steady, pulse, momentary, toggle or

off.

BUTTON ACTION

OUT RST

RST (Sensor Reset) - Causes the panel to perform a standard Sensor Reset.

UN (Unused) - The button is not used and performs no action.

19.11.8

Button Press Time

BUTTON

PRESS TIME: XXXXX

This option speciﬁes the amount of time (SHORT or LONG) the user must press

the button before the key fob sends a message to the wireless receiver. The

default press time displays. Press any Select key to set the Button Press Time

for Arm, Disarm, Toggle, Status, Output, and Sensor Reset.

Note: The Button Press Time is not programmable on Panic (PN or PN2),

Emergency (EM or EM2) or Unused (UN) zones. For those zones the button press

time is always two (2) seconds.

SHORT - Press the button for one-half (1/2) second to send the message to the

wireless receiver.

PRESS TIME:

SHORT

LONG

LONG - Press the button for two (2) seconds to send the message to the wireless

receiver.

19.11.9

Arm/Disarm Area Selection

In an Area system or Home/Sleep/Away with Guest system, this speciﬁes the

areas to be armed/disarmed by the Key Fob button being programmed. To

select an area between 1 and 32, enter the area number using the keypad digit

keys. Default is no areas enabled.

ARM/DIS AREAS:

In order to arm or disarm selected areas, the Proﬁle assigned to the User

Number needs to have the same area numbers selected. Any area may be

selected at Arm/Disarm Areas but only matching area numbers are armed or

disarmed when the speciﬁc button is pressed. For example, in Areas selection,

areas 1, 3, and 7 are selected. In the User Proﬁle Arm and Disarm Areas, areas

1, 2, 4, and 7 are selected. When the user presses the button to Arm or Disarm

area(s), only matching areas 1 and 7 Arm/Disarm.

Note: When more areas are selected at Arm/Disarm Areas than are authorized

in the User Proﬁle, in the future the user can be given access authority to

additional areas through the User Proﬁle without requiring additional panel

programming to select Arm/Disarm Areas. See User Proﬁles in the Appendix or

refer to the XR500 Series Canadian User’s Guide (LT-0683CAN).

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

zone informaTion

In an All/Perimeter or Home/Sleep/Away system, this speciﬁes the area to be

armed by the Key Fob button being programmed. For All/Perimeter systems,

choose PERIM or ALL, for Home/Sleep/Away or Home/Away systems, choose

HOME, SLEEP, or AWAY.

ARM AREAS: PERIM

Note: Areas 3 and higher in an All/Perimeter system, and areas 4 and higher in a

Home/Sleep/Away system are not available for use.

After selecting the areas, for one-button key fobs the Zone No.: prompt

displays. For two-button or four-button key fobs, the Key Fob Button Selection

option displays to program additional buttons.

19.11.10 OUTPUT NO: XXX

Output Number

You can specify a relay output to operate when OUT (Output), PN (Panic), PN2

(Panic 2), EM (Emergency), or EM2 (Emergency 2) is selected for a key fob

Button Action and the button is pressed. Valid range is 1 to 6, 500 to 999,

D1 to D16, or G1 to G20. For an output turned on by a PN, PN2, EM, or EM2

button action, the output turns off when any area is disarmed.

To enter an output number, press a top row Select key followed by the output

number. Press the COMMAND key.

19.11.11

Output Action

OUTPUT ACTION:

yyy: XXXXXXXX

This option allows you to deﬁne the output action (STD, PLS, MOM, TGL, OFF)

for the selected output number. The default is Steady.

yyy = the name of the button being programmed (TOP, BTM, LFT, RGT).

xxxxxxxx = the currently deﬁned output action.

STD (Steady) - The output is turned on and remains on.

OUTPUT ACTION?

STD PLS MOM TGL

PLS (Pulse) - The output alternates one second on and one second off.

The pulsing rate for a Model 716 relay attached to the LX-Bus is 1.6 seconds.

Note: Pulse is not available for key fob button output programmed D1 to D16 or

G1 to G20.

MOM (Momentary) - The output is turned on only once for one second.

TGL (Toggle) - The output alternates between the on state and off state. Each

button press toggles the output state.

Note: Toggle is not available for key fob button output programmed G1 to G20.

OFF (Off) - The output is turned off. If programmed, the output was turned

on by some other means such as another button press, a zone action, or a

schedule.

OUTPUT ACTION?

OFF

Note: When the output is assigned to PN/PN2 or EM/EM2 button action and is

turned on, the output turns off when any area is disarmed.

When the output action is steady, pulse or toggle and the output is turned on,

the output remains on until:

— the output cutoff time expires

— the output is reset from the keypad menu

— toggled off

19.11.12 NEXT ZONE NO YES Next Zone

Select YES to return to the ZONE NO: - prompt to program a new zone. Select

NO to display the Alarm Action option.

Note: All wireless programming is stored in the XR500 Series Canadian panel. The 1100X Wireless

Receiver obtains the necessary programming information from the panel each time the receiver powers

up, when the programmer STOP routine is selected or the panel is reset. The receiver memory refresh

takes up to 10 seconds to complete depending on the number of wireless zones programmed and the Red

LED remains on during this time. Normal receiver operation is inhibited during the memory refresh period.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

zone informaTion

FA Series Wireless

For an FA Series Remote Wireless Receiver set the House Code to 99. See House Code programming in

System Options. Only zones 500 to 699 can be programmed as FA Series Wireless zones for maximum of

200 Wireless Zones.

For a DMP 1100X Wireless Receiver see section 16.10.

19.12

Wireless

ZONE INFORMATION

WIRELESS? NO YES

Select YES to program a wireless zone connected to an FA Series FA400-DMP Remote

Wireless Receiver. Press the COMMAND key to continue with wireless programming.

19.12.1 CHECK IN TM:

60 Check-in Time

You can set wireless transmitters to check in automatically every 10, 30, or 60

seconds or not at all. To change the 60 second default, press any top row Select

key to display NONE 10 30 60. Select the check-in time you want for this zone.

Note: Refer to the Wireless Check-in and Supervision Time Deﬁnitions section of

the Appendix for supervision information.

19.12.2 INT CONT NO YES Internal Contact

Select YES to use an internal contact on the wireless transmitter. Select NO

to use an external contact. When you select NO, the following two prompts

display.

19.12.3 EOL

NO YES End-of-Line

Select YES to supervise an external contact connected to the wireless

transmitter. At the contact, install a 2.2k Ohm End-of-Line resistor in parallel

for Normally Open contacts and in series for Normally Closed contacts.

19.12.4 NRM OPEN NO YES Normally Open

Select NO if the contact connected to the wireless transmitter is Normally

Closed.

19.12.5

NEXT ZONE NO YES Next Zone

Select YES to return to the ZONE NO: - prompt to program a new zone. Select

NO to display the Alarm Action option.

19.13 ALARM ACTION . . . . Alarm Action

This option allows you to change any Zone Type standard deﬁnitions. When the Zone

Type is speciﬁed, the Alarm Action for that zone is stored in memory.

If the Zone Type is Blank, Night, Day, Exit, Auxiliary 1, or Auxiliary 2 it is a

non-24-hour zone and the Alarm Action programing begins with Disarmed Open.

If the Zone Type is Fire, Panic, Emergency, or Supervisory it is a 24-hour zone that is

always armed and the Alarm Action programming begins with Armed Open.

The Fire Verify Zone Type functions the same as Fire Type, with the following

exceptions: When a Fire Verify zone initiates an alarm, the panel performs a Sensor

Reset. If any Fire Verify zone initiates an alarm within 120 seconds after the

reset, an alarm is indicated. If an alarm is initiated after 120 seconds, the cycle is

repeated and a zone fault report is sent to the receiver.

Do NOT program Fire Verify Zone Types for Zone Retard.

19.14 DISARMED OPEN

Disarmed Open

Deﬁnes the action taken by the panel when the zone is opened while the area is

disarmed. There are three actions to deﬁne: Report to transmit, Relay Output to

activate, and Relay Output action.

You must also make these selections for the Disarmed Short, Armed Open, and Armed

Short zone conditions. Press COMMAND to continue.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

zone informaTion

19.15

Report to Transmit

TROUBLE

MSG:

Press any Select key to display the following report options: A, T, L, S, C, and - (dash).

ALARM - Select A to send an alarm report to the receiver and activate the bell

output according to zone type. The zone name appears in the panel alarmed zones

and status lists.

TROUBLE - Select T to send a trouble report to the receiver. The zone name

appears in the panel alarmed zones and status lists.

LOCAL - When you select L, an alarm report is NOT sent to the receiver. The bell

output activates and the zone name appears in the panel alarmed zones and status

lists.

- (Dash) - When you select a – (dash), reports are NOT sent to the receiver. The bell

output does not activate and there is no display in the panel alarmed zones or status

list. Only the relay output selected in the next section operates.

DOOR PROPPED - Selecting D allows the following operation: The time programmed

into ENTRY DLY 4 in the System Option section begins to count without displaying

on keypad. If the time expires and the zone has not returned to normal, the keypad

trouble buzzer starts and CLOSE THE DOOR appears on the keypads programmed into

the PREWARN ADDRESS section. The time programmed into ENTRY DLY 4 begins to

count down again internally. If the time expires a second time and the zone has not

returned to normal, a fault report is sent to the receiver and the zone name - OPEN

message displays on the keypads until a code is entered. The bell output does not

activate for the Door Propped operation.

SILENCE/RESET - Select S when the zone (not FI, SV, or FV) is connected to a DMP

Model 303 Silence/Reset switch, the zone can be used to silence the alarm bell and

perform a sensor reset without using a keypad. A report is NOT sent to the receiver

except for the bell silence report.

CANCEL AMBUSH - Select C for the zone to cancel the Early Morning Ambush timer

and stop an Ambush message from being sent to the receiver. Faulting the zone

takes the place of a second user code being entered at the keypad and is only

available for non-ﬁre type zones. Area assignment for the zone does not affect this

option. See Early Morning Ambush in Area Information programming.

19.16 OUTPUT NO:

Output Number

You can specify any of the Relay Outputs on the XR500 Series panel to be activated

by a zone condition (1 to 6, 500 to 999 if Model 716 used, D1 to D16, G1 to G20).

The output can be activated regardless of the report to transmit or whether or not

the zone is programmed as local. An output activated by an armed zone is turned

off when the zone area is disarmed by a user.

To enter an output number, press a top row Select key followed by the output

number. Press the COMMAND key.

19.17 OUTPUT:

NONE Output Action

Entering an Output Number displays this prompt. This prompt allows you to assign

an output action to the relay: Steady, Pulse, Momentary, or Follow.

Note: Some wireless devices whether powered using an AC adaptor or a battery,

ignore some output action programming.

STD PLS MOM FOLW STEADY - The output is turned on and remains on until the area is disarmed, an

output cutoff time expires, or the output is reset from the keypad menu.

PULSE - The output alternates one second on and one second off.

Note: The pulsing rate for a Model 716 relay attached to the LX-Bus is 1.6 seconds.

MOMENTARY - The output is turned on only once for one second.

FOLLOW - The output is turned on and remains on while the zone is in an off

normal, or bad condition. When the zone restores, the output is turned off.

After you make the three selections in the sections above, the display prompts you for the same three

selections for Disarmed Short, Armed Open, and Armed Short conditions. If the zone is a 24-hour type,

only the Armed Open and Armed Short conditions display. When you have programmed all of the zone

conditions, the Swinger Bypass selection then displays.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

zone informaTion

19.18

Swinger Bypass

SWGR BYP NO YES

Selecting YES allows the zone to be swinger bypassed by the panel according to the

speciﬁcations programmed in Swinger Bypass Trips and Reset Swinger Bypass. The

Bypass condition displays in the keypad Status List. Selecting NO disables swinger

bypassing for this zone.

How it works

If within one hour, a zone trips the total number of times as speciﬁed in Swinger

Bypass Trips, the panel bypasses it until the following conditions occur; the area

in which the zone is assigned is disarmed, the zone is manually reset through the

Bypass Zones? keypad User Menu function, the zone remains normal for one hour and

the Reset Swinger Bypass is YES.

If the zone trips fewer than the speciﬁed times within one hour, the bypass trip

counter returns to 0 (zero) and the process must be repeated.

A report of the swinger bypass is sent to the receiver if Bypass Reports is YES.

19.19 PREWARN KEYPADS: Prewarn Keypad Addresses

At the entry delay start, all keypad addresses selected here display ENTER CODE:-.

If you want the prewarn to sound at all 16 addresses, leave the default setting.

To delete an address, press the matching number on the keypad. To disable

prewarning at all keypads, press a top row Select key to clear the addresses shown.

Press the COMMAND key when the address selection is complete.

The prewarn tone stops at the keypad where the ﬁrst user code digit is entered. If

no keys are pressed for ﬁve seconds or an invalid user code is entered, the prewarn

tone resumes at that keypad.

19.20 ENTRY DELAY:

Entry Delay

Select the entry timer for this zone. Entry timers 1 to 4 are programmed in System

Options.

19.21 RETARD

NO YES Zone Retard Delay

When you select YES, the zone operates with the zone retard delay. The retard

functions only in zone short conditions.

The zone must remain shorted for the full length of the retard delay before the

panel recognizes its condition. If you select NO, the zone operates without a retard

delay.

19.22 PRESGNL KEYPADS: Presignal Keypad Addresses

You can enable any combination of keypad addresses to sound a presignal tone

during the time a zone is in retard delay. The presignal tone silences when the zone

restores or the retard delay expires.

To enable a presignal address, press any top row Select key followed by the number

of the keypad address. You can enable the presignal for all 16 keypad addresses.

To disable a presignal address press the matching number digit again. Press the

COMMAND key when the address selection is complete. The Presignal prompt is only

displayed when Retard is selected as YES.

19.23 FAST RSP NO YES Fast Response

Select YES to provide a zone response time of 167ms. Select NO to provide a normal

zone response time of 500ms. Zones 500 to 999 have a ﬁxed response time and do

not display this prompt.

19.24

Cross Zone

CRS ZONE NO YES

Select YES to enable cross zoning for this zone. Cross zoning requires one or more armed

zones to fault within a programmed time before an alarm report is sent to the receiver.

When the ﬁrst cross zoned zone trips, the cross zone time speciﬁed in System

Options begins to count down. When a second cross zoned zone trips or the ﬁrst

zone trips a second time before the end of the count down, the bell action assigned

to the zone activates and the panel sends an alarm report for both zones.

If no other cross zoned zone trips before the cross zone time expires, the panel

sends only a zone fault report to the receiver.

Cross zoning is not compatible with all zone types: You can not enable cross zoning

for Fire verify zones or for any Fire zones that have Retard Delay enabled.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

zone informaTion

19.25 PRIORITY NO YES Priority

Select YES to provide additional protection for the premises by requiring this zone to

be in a normal condition before its assigned area can be armed.

19.26

Fire Panel Slave Input

FIRE PANEL SLAVE

This option is available on Fire Zones (FI) only and allows a ﬁre zone the ability to

provide slave communication operation for a separate ﬁre alarm control panel. If

YES, this zone will transmit a restoral immediately when restored by the ﬁre panel

being monitored. A sensor reset is not required to generate the restoral message.

If NO, this zone will operate as a standard ﬁre type zone and a sensor reset is

required before the zone will return to normal. Default is NO.

INPUT:

NO YES

19.27

19.28

Area Follower

FOLLOW AREA:

Allows Night, Day, Aux 1, or Aux 2 burglary zones to be delayed by following any exit

or entry delay that is currently running in the area that is speciﬁed. Default is 0.

Zone Real-Time Status

Selecting YES allows Real-Time Status reports, such as Door Open or Closed with

zone number, to be sent using PC Log reporting. Selecting NO disables Real-Time

Status for this zone. Default is NO.

ZONE REAL-TIME

STATUS NO YES

19.28.1

Door Number

DOOR NUMBER: 0

If ZONE REAL-TIME STATUS is selected as YES, enter a door number (keypad bus

address) of 1-16. When a door number is selected, the door number is included

in the status report instead of the zone number. Enter 0 (zero) to disable this

feature and report the zone number. Default is 0 (no door).

19.29 ZONE AUDIT DAYS: Zone Audit Days

Enter the number of days (0 to 365) allowed to elapse without the zone being tripped

before a fault message is sent. The message is sent to the receiver(s) programmed

to receive Supervisory/Trouble Reports at 10:00 am following the expiration of the

timer. Each time the zone is tripped, the Zone Audit Days timer restarts and begins

to countdown the number of days programmed. After the countdown expires, a fault

message is sent and the Zone Audit Days timer restarts and begins to countdown the

number of days programmed. Available for all zone types except ﬁre and ﬁre verify.

Enter 0 (zero) to disable this function. Default is 0 (zero).

19.30

Report with Account Number for Area

This option is only available for 24-hour zone types (Fire, Fire Verify, Panic,

Emergency, or Supervisory).

REPORT WITH ACCT

NO. FOR AREA:

Enter the area number (1-32) to assign as a 24-hour zone type. This option sends

the account number of the programmed area with messages. If the entered area

number does not exist or is not valid, the account number programmed in the

Communication section is sent. Select 0 (zero) to have the report sent with the

account number programmed in Communication. Default is 0

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

SToP

Stop

20.1

STOP

Stop

Save Programming

WHEN ANY PANEL PROGRAMMING IS CHANGED, THE STOP ROUTINE MUST BE RUN

AND ‘SAVING PROGRAM’ MUST DISPLAY ON THE KEYPAD IN ORDER TO SAVE THE

PROGRAMMING CHANGES.

At the STOP prompt, pressing any Select key allows you to exit the Programmer

function of the panel. When selected, the panel performs an internal reset and

exits the programmer.

The STOP routine causes the following conditions to occur:

• All 1100 Series DMP Wireless transmitters are reset to NORMAL

• The panel Status List is cleared

During the reset, all keypad displays are momentarily blank for two seconds. After

the reset, the programming function terminates and the keypads return to the status

list display.

The STOP prompt does not disarm the system. Any new areas or zones that were

added during programming are not armed until the system is disarmed and armed

again.

Missing LX-Bus™ Modules Displayed

The Programmer includes a feature following the STOP routine that displays the

name of any programmed LX-Bus module not currently connected to the panel. For

example, if you had enabled any LX-Bus options and not yet installed a 481 LX-Bus

Expansion Card, after the STOP routine the panel displays NO LXBUS CARD. This is a

helpful reminder to install the card. This feature can also be a troubleshooting tool

to indicate a problem if you installed the card and this message still displays. The

following list shows the different messages and their associated LX-Bus cards.

Keypad Display

NO LXBUS CARD

NO PRINTER CARD

NO HOST CARD

Missing Card

481 LX-Bus™ Expansion Card

462P Printer Interface Card

462N Network Interface Card

(with NETWORK communication selected)

The above messages clear automatically from the keypad after a few moments.

Power Up

When the XR500 Series Canadian panel is powered up after an AC power failure,

any zone transitions are not recognized for 120 seconds. Normal zone processing

resumes at the end of the 120 seconds.

Set Lockout Code

SeT loCkouT Code

21.1

SET LOCKOUT CODE Set Lockout Code

Pressing COMMAND at the STOP prompt displays SET LOCKOUT CODE. This allows

you to program a code that is then required to gain access to the panel internal

Programmer through the keypad. You can change this code at any time to any

combination of numbers from three to ﬁve digits long. You do not need to enter

leading zeros when using the lockout code. Initializing the panel does not clear a

Lockout Code. Lockout Codes can be changed through Remote Link.

Once you have changed the code, it is important to write it down somewhere and

store it in a safe place. Lost Lockout Codes require the panel to be sent back to

DMP for repair. You may cancel a Lockout Code by entering 00000 at the Set Lockout

Code command.

Lockout Code restriction

Do not set a Lockout Code higher than 65535.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

feaTure uPgrade

Feature Upgrade

22.1

FEATURE UPGRADE

Feature Upgrade

In the Programming Menu, pressing COMMAND at the SET LOCKOUT CODE prompt

displays FEATURE UPGRADE. This allows you to enable additional features in the

panel. Press any top row Select key to display the ﬁrst available feature. ENABLED

or DISABLED displays indicating whether this feature is currently used in this panel.

Press the COMMAND key to display additional feature(s).

ENTER KEY

To enable a feature, press any top row Select key anywhere in the features list to

display the ENTER KEY prompt.

Enter the factory-supplied feature key for the speciﬁc panel and press the COMMAND

key. The feature speciﬁc to the key displays as ENABLED.

Note: XR500 Series version 106 or higher panels require a six (6) character feature

key. Version 105 panels require a 16-character feature key.

If the feature key entered is not accepted, the ENTER KEY prompt displays again.

Re-enter the feature key and press the COMMAND key.

ENCRYPTION

DISABLED

22.1.1

Encryption

Enable this feature to provide 128 bit AES data encryption. This feature upgrade

can only be enabled on an XR500N panel version 105 or higher. For installations

where an XR500 panel is installed, it is recommended the XR500 be replaced with an

XR500E panel.

To complete encryption installation, access System Status in the User Menu to verify

the encryption status (ON or OFF). If the status displays OFF, it indicates that the

Passphrase has not been entered and data transmissions are not encrypted. See

Network Options to set up a Passphrase.

ALL NO YES OPTN

DISABLED

22.1.2

22.1.3

All No Yes Option

This feature offers the ability to disable the ALL NO YES option at arming or

disarming. When this feature is enabled, the ALL NO YES option does not display

at any system keypad during arming or disarming. Each area assigned to the user

proﬁle is chosen to be armed or disarmed independently.

SVC USER AUTH

DISABLED

Service User Authentication

This feature offers the ability to authenticate service personnel before allowing

access to panel programming or performing any user operations. When this feature

is enabled and a valid Service User code is entered for system operation or 6653 is

entered for programming, the Service Code entry option displays.

When the service person enters the Service Code, the panel authenticates the code

with the Service Code preprogrammed in the SCS-1R receiver, and access to panel

programming or the User Menu is granted. The Service Code can be used for system

operation for 30 minutes before authenticating again. If the code entered is not

validated, access to programming or the User Menu using the Service User code is

denied.

Note: The Service User code is user number zero (0) and can only be created in the

panel remotely. The SCS-1R receiver must have ﬁrmware version 902 or higher to

authenticate service personnel.

Purchasing Feature Upgrades

To purchase a feature upgrade, you may contact DMP Customer Service with the

feature you would like to enable and the panel serial number. The serial number(s)

should be sent in writing via e-mail or fax. A separate feature key is issued for each

panel. The feature key only enables the requested feature on the speciﬁed panel.

The panel serial number can be located several different ways:

• Printed on a label located on the right side of the XR500 PCB.

• Using panel diagnostics. See the Appendix.

• Using Remote Link™ (version 1.18 or greater). See the Remote Link User’s

Guide (LT-0565).

— Initial Panel Connection screen

— System Information screen.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

aPPendiX

Appendix

23.1 False Alarm Reduction

System Recently Armed report

The System Recently Armed report (S78) is sent to the receiver when a burglary zone goes into alarm

within two minutes of the system being armed.

23.2 Diagnostics function

The XR500 Series Canadian panel contains a Diagnostics function that allows you to test the communication

integrity of the LX-Bus™, identify individual zones, and also display the present electrical state of any

zone. The Diagnostics function also allows you to test the integrity of the cellular communication, cellular

signal, and email communication. To use Diagnostics, reset the panel, enter the Diagnostics code 2313

(DIAG), and press COMMAND.

Test LX-Bus

The ﬁrst Diagnostic function you displayed is: TEST LX-BUS. This function allows you to test the ability

of the 481, 462N, 462P, 462FM, and 472 Interface Cards to communicate with zone and output expander

modules connected to their LX-Bus circuits.

To continue, press any top row Select key. The keypad displays LX-BUS:. Using the digit keys, enter the

LX-Bus number, 1 to 5, to test that LX-Bus circuit. The keypad now displays ADDRESS: - . Enter a 2-digit

LX-Bus device address and press COMMAND. When testing LX-Bus devices, enter only the addresses to

which the modules have been set.

Important Note: A device address is not the same as a zone number. If you are testing 714 or 715 Zone

Expander Modules, which each contain four zones, the device address is the ﬁrst zone number. When the

panel polls a 714 on the LX-Bus, it recognizes it as a four zone device and does not poll the remaining

three zones. The 714 module internally polls the remaining zones and transmits any status changes to the

panel. This greatly reduces the amount of time it takes the panel to poll all LX-Bus devices.

The keypad next displays TESTING . . . STOP during the device testing. At any time, you can Select

STOP to end polling. The panel records the number of no responses from the device. If all polls are

received back by the panel correctly, the keypad displays 00000/65535 FAIL.

If one or more polling attempts fail, the keypad displays * * * * */65535 FAIL with the * representing the

number of failed polling attempts. A display of 65535/65535 FAIL indicates a problem with the interface

card or its LX-Bus wiring such as a bad or broken wire, harness not properly connected, or excessive noise

or distance. It can also mean that a zone number was entered that did not match a device address. Press

the Back Arrow key to enter a new device address or press COMMAND to exit the TEST LX-BUS.

Zone Finder

The second Diagnostic function is the Zone Finder. Press COMMAND to display ZONE FINDER. This function

allows you to identify individual zones on devices connected to the LX-Bus of an interface card, the panel,

or any zones on the keypad data bus. To use ZONE FINDER, press any top row Select key. The display

changes to FAULT ZONE. The next zone on the system that changes from a normal to an open or shorted

state is displayed as ZONE NO: * * *. To continue, press the Back Arrow key.

Zone State

Press the COMMAND to display the third Diagnostic function: ZONE STATE. This function allows you to

enter any zone number and check its current electrical state (Normal, Open, or Shorted). Press any Select

key. The display changes to ZONE NUMBER: _ . Enter in the zone number you want to check and press

COMMAND. The panel displays the current state of the zone as NRML (normal), OPEN, or SHORT.

LX-Bus Status

The fourth Diagnostic function is the LX-BUS STATUS. This function allows the panel to poll all devices

connected to the LX-Bus of an interface card and check for any Overlapped, Missing, or Extra addresses.

Below is a description of each status item:

Overlap - An overlap occurs when one device address is the same as any of the last three zones on another

714 or 715. The overlap feature cannot determine when two devices have the same address.

Example: Model 714 Address 00 = Zones 500 501 502 503, and the Model 711 Address 02 = Zone 502.

Zone 502 would report as an Overlap because both the 714 and 711 have devices set to 502.

Missing - A missing occurs when a zone between 500 and 999 has been programmed in ZONE INFORMATION

and no device with that zone address has been installed on the LX-Bus. To correct the problem, check

your zone programming and zone expansion module addressing.

Extra - A device is installed on the LX-Bus but none of its zones are programmed into the system.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

aPPendiX

MAC Address

Short for Media Access Control address. This hardware address uniquely identiﬁes each network node. Not

to be confused with an IP address, which is assignable. In the Diagnostics function, the MAC address is the

panel on-board network hardware address. Press any top row Select key to display the panel MAC address.

Press the COMMAND key to view the next prompt.

Serial Number

This number is the network communicator serial number. Reference this number for communicator date-

of-manufacture, hardware version, etc. Press any top row Select key to display the Serial Number. Press

the COMMAND key to view the next prompt.

Current Flash

This option displays Flash 1 or Flash 2 indicating which physical ﬂash chip the panel is currently using. Press any

top row Select key to display the current ﬂash information. Press the COMMAND key to view the next prompt.

Communication Status

This option tests the individual components of cellular or network communication. The displayed results

are shown below.

Cellular Results:

Successful Display

MODEM OPERATING

TOWER DETECTED

SIM REGISTERED

APN ACCEPTED

Failure Display

NO MODEM FOUND

NO TOWER

NOT REGISTERED

APN ERROR

CELL COMM GOOD

NO ACK RECEIVED

Network Results:

Successful Display

LINK OK

Failure Display

LINK ERROR

DHCP OK

DHCP ERROR

NO GATEWAY

NO DESTINATION

GATEWAY FOUND

DEST FOUND

COMM PATH GOOD

NOT CONNECTED

NO ACK RECEIVED

Cellular Signal

This option provides a way to test the cellular signal strength. Press any top row Select key to test the cell

SIGNAL: XXXXXXX

signal. The display shows:

. The x’s represent the signal strength 0-7.

Email Status

The Email Status menu, located in Diagnostics, tests each component of the panel’s e-mail

communication. The test proceeds until the ﬁrst component failure or until all components have been

tested with positive results. The test screen displays after each component and displays for two seconds

or until the CMD key has been pressed. The displayed results are shown below.

Email Results:

Successful Display

EMAIL ENABLED

LINK OK

Failure Display

Successful Display

FROM ADDR SENT

DEST ADDR SENT

DATA MODE SENT

MESSAGE SENT

Failure Display

EMAIL DISABLED

FROM ADDR FAILED

DEST ADDR FAILED

DATA MODE FAILED

MSG SEND FAILED

DISCONNECT FAIL

LINK ERROR

SMTP SERVER OK

DEST ADDRESS OK

CONNECTING

INVALID SERVER

DEST ADDR FAILED

CANNOT CONNECT

AUTH MODE FAILED

BAD PASSWORD (or USERNAME)

DISCONNECTED

EMAIL SUCCESS

AUTH MODE SENT

PASSWORD SENT

Exiting the Diagnostics program

To exit the Diagnostics function, press the COMMAND key until STOP displays. Press any Select key to exit

the diagnostics function. The keypad returns to the Status List display.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

aPPendiX

23.3 Using the 984 Command Function

This feature allows you to connect to a service receiver, is used primarily to bring a new account on-line

and upload panel programming completed in Remote Link™.

Note: When not in the Programming Menu, the function 984 + COMMAND can be entered at the keypad,

and a remote options menu appears. This menu contains the following options:

NUMBER: The panel allows you to enter into the keypad a phone number you want the panel to dial.

Enter any required preﬁxes and area codes. After completing panel programming in Remote Link, set a trap

to seize the panel when it calls. Traps are set by selecting Panel > Trap. Refer to the Remote Link User’s

Guide (LT-0565), or the Remote Link Help File.

Then, from the panel, enter 984 and press the COMMAND key, while the panel is in the Status List. The

keypad display changes to NBR TEST PICKUP. Press the Select key under NBR. Enter the phone number

for the service receiver connected to the Remote Link computer. Press each number key slowly and

deliberately. The panel dials each number as it is pressed. If you make a mistake, press the Back Arrow

key. The panel stops dialing and return to the Status List.

You can enter up to 32 characters for the phone number. Once you have entered 16 characters the LCD

display is full: Press the COMMAND key to enter the ﬁnal 16 characters. To enter a # (pound sign) press the

‘0’ then the fourth (far right) Select key, and to enter an * (asterisk) press the third Select key. Program

a pause by entering the letter P. Program CID message communication by entering the letter T in the ﬁrst

position. Cancel call waiting by entering *70P as the ﬁrst characters. These characters are counted as

part of the allowable 32 characters. Press COMMAND after you enter the phone number.

The panel calls the receiver connected to Remote Link to download the new programming. Remote Link

then traps the panel.

Note: The panel makes ten attempts to reach the receiver. While attempting to contact the receiver, if

the panel needs to send an alarm report, the panel stops dialing and uses the phone line to send its report.

TEST: The panel allows you to perform a Communication Status Test on each component of the

panel’s cellular or network communication paths. While the Status List displays, enter 984 and press the

COMMAND key. The keypad display changes to NBR TEST PICKUP. Press the Select key under TEST to

allow the panel to perform a Communication Status Test. The display prompts the user for a user code to

be entered. The user code must have the authority to perform a System Test.

Upon entry of a Cell or Network path when prompted, the test runs and the results display on the keypad.

See Diagnostic Functions section for a description of the Communication Status results.

PICKUP: The panel picks up the phone line when Remote Link™ calls in. The phone must be ringing

before selecting PICKUP. After completing panel programming in Remote Link, connect to the panel by

selecting Panel > Connect. Refer to the Remote Link User’s Guide (LT-0565), or Help File for complete

information about connecting to panels.

While the panel displays in the status list and the telephone line at the panel rings, enter 984 and press

the COMMAND key. The keypad display changes to NBR TEST PICKUP. Press the Select key under PICKUP

to allow the panel to seize the line. The panel immediately seizes the phone line and sends a carrier

tone to the receiver. A veriﬁcation process occurs and, if successful, the panel grants remote access to its

programming and Event Buffer.

After the panel has seized the line, send the ﬁle from Remote Link by selecting Panel > Send. Remote Link

then uploads the new programming into the panel. You may also Request Events by selecting Panel > Request

Events in Remote Link. The panel begins sending the ﬁrst event or access that occurred on or after the start

date speciﬁed by Remote Link and ﬁnishes by sending the last event or access that occurred on or before the

end date speciﬁed by Remote Link. If necessary, a Request Events upload in progress can be cancelled.

Keypad Displays

When the PICKUP option is used, the keypad displays LINE SEIZED. This indicates that the panel has

seized the line and is executing its program. If the line cannot be accessed, or if the PICKUP option is

used before all connect attempts are made, the keypad displays SYSTEM BUSY.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

aPPendiX

23.4 Using the Walk Test

The XR500 Series Canadian panel provides a walk test feature that allows a single technician to test the

protection devices connected to zones on the system. Conduct the Walk Test within 30 minutes of resetting

the panel. The Walk Test automatically ends if no zones are tripped for 20 minutes. TEST IN PROGRESS

displays at all keypads programmed with the same Area Display features. When ﬁve minutes remain, TEST

END WARNING displays. The Walk Test only tests zones assigned to the areas programmed into the keypad

in Area Display. If any areas are armed the Walk Test does not start and SYSTEM ARMED displays.

WALK TEST

Walk Test

To conduct the Walk Test, reset the control panel by momentarily placing a jumper

on J16. From the keypad, enter the code 8144. The keypad displays WALK TEST

for four seconds. If the system is monitored and the communication type is DD or

NET, the system sends a System Test Begin report to the central station. After four

seconds, the keypad displays the zone type choices for testing.

Note: If ENHANCED ZONE TEST in System Options is set to YES, the Walk Test can

be limited to only operate during the Area 32, Shift 4 schedule if programmed. If no

schedule is entered, the walk test always operates.

FI PN SV Zone Types

Select the zone type you want to test. An asterisk next to the zone type indicates

the zone type chosen for testing. Press the Select key again to deselect the zone

type. When you have selected all the zone types you want for testing, press the

COMMAND key to display the next Walk Test option. Pressing the Back Arrow key

exits the Walk Test.

Note: For the Wireless Check-in Test, make sure no zone types are selected and

press the COMMAND key. Pressing the Back Arrow key exits the Walk Test.

BG (Burglary zones) - Select BG to test burglary zones. Includes all NT, DY, EX, A1,

and A2 zones.

FI (Fire zones) - Select FI to test ﬁre zones. Includes all FI and FV zones.

PN (Panic zones) - Select PN to test panic zones. Includes all PN and EM zones.

SV (Supervisory zones) - Select SV to test supervisory zones. Includes all SV zones.

Note: During the Walk Test, trip each zone device or button on the system for 1 to 2

seconds. You do NOT have to hold the zones for 2 seconds in normal mode for PN

type zones. You are only required to hold the panic during the Walk Test because

the zone takes additional time to report when the system is in test mode.

WLS PIR

WLS (Wireless Check-in Test) - Select WLS to automatically test wireless transmitter

communications. Includes all wireless devices except key fobs and transmitters

programmed for a supervision time of 0 (zero).

PIR (Wireless PIR Walk Test) - The PIR Walk Test allows the installer to verify the 1126

operation. When enabled, the 1126 LED ﬂashes each time motion is detected for up to

30 minutes. This is a local test only and no messages are sent to the Central Station.

BELL NO YES PULS Bell Action

This option selects the bell output action when a zone under test faults. This option

allows the panel bell, and/or burglary bell, and/or ﬁre bell to turn ON and then OFF

each time a zone is tripped (opened or shorted).

NO - Select NO for no bell output action during Walk Test.

YES - Select YES to turn on any bell output for 2 seconds during Walk Test.

PULS - Select PULS to turn on any bell output for 1/4 second during Walk Test. Any

LX-Bus device output turns on for 1.6 seconds due to the polling cycle.

TRIPS: XXX

END Trip Counter For Walk Test

Once in the Walk Test, walk around and trip each protective device. Continue

tripping devices until the entire system is tested.

With each zone trip during the Walk Test:

• Keypad display increments each time a selected zone is opened or shorted

• The keypad buzzes for two seconds

• The panel sounds the alarm bells as programmed in Bell Action

• Each time a FI, FV, or SV zone trips, a Sensor Reset occurs.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

aPPendiX

If ENHANCED ZONE TEST is selected as YES:

A Verify message is sent at the time the zone trip occurs instead of at the end of the

Walk Test. For FI, FV or SV zone types, the Verify message is sent at the initial trip.

For all other zone types, the Verify message is sent when the zone restores. This

allows the Central Station to count the number of devices per zone.

END - Select END to stop the Walk Test. When the Walk Test ends or a 20-minute

time-out expires, a ﬁnal Sensor Reset occurs. The System Test End message is

sent to the receiver along with Verify and Fail messages for each zone under test.

Faulted zones then display on the keypad.

Trip Counter For DMP Wireless Check-in Test (WLS)

Displays the number of wireless zones that automatically communicate a supervision

check-in message.

CKIN:XXX/ZZZ

END

• The number of zones that check in. (XXX in the example).

• The total number of wireless zones programmed for supervision that should

check in. (ZZZ in the example).

END - Select END to stop the Wireless Check-in Test. When the test ends or

a 20-minute time-out expires, normal wireless zone processing returns. If

all transmitters check-in, both numbers match within three (3) minutes. If a

transmitter has multiple zones (1101, 1114, etc.), all zones are included in the

counts. Failed wireless zones display on the keypad.

TEST END WARNING Test End Warning

When ﬁve minutes remain on the 20 minute Walk Test timer, the keypad displays

TEST END WARNING. If no additional test zone trips occur, the test ends and a ﬁnal

Sensor Reset automatically occurs. The System Test End message is sent to the

receiver along with Verify and Fail messages for each zone under Walk test. Faulted

zones then display on the keypad.

Failed Zones Display

SOUTH LOBBY

ZONE: 10

-FAIL For each zone that did not trip (failed) at least once during the Walk Test, all

keypads with matching Area Display programming display the zone name and number

and buzz for one second. Any selected (*FI *PN *SV) 24-hour zone that is faulted at

the end of the Walk Test displays a trouble condition for that zone regardless of the

message programmed for the open or short condition of the zone and a zone trouble

is sent to the receiver. Press the COMMAND key to display the next failed zone.

Note: For the Wireless Check-in Test, failed wireless zones display only on the

keypad. Zone Verify/Fail reports are not sent to the central station receiver for the

wireless check-in test.

Local Printer for Walk Test

When the Walk Test is completed, a Verify or Fail message for each zone tested prints to the local printer.

The Walk Test messages printing is enabled through Printer Reports programming.

Note: If ENHANCED ZONE TEST is selected as YES, the Verify messages are printed at the time the zone

trip occurs and not printed at the test end.

23.5 Keypad Speaker Operation

When using LCD Keypads, the panel provides distinct speaker tones from the keypad for Fire, Burglary,

Zone Monitor, and Prewarn events. The list below details the conditions under which the speaker is turned

on and off for each event.

Fire

On - Fire zone alarm and Bell Output or Fire Bell Output is ON.

Off - Alarm Silence.

Burglary

On - Burglary zone alarm and Bell Output or Burglary Bell Output is ON.

Off - Alarm Silence.

Zone Monitor On - One time only when a monitored zone is tripped.

Off - After one tone.

Prewarn

On - During Entry Delay.

Off - When Entry Delay expires.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

aPPendiX

23.6 Cross Zoning

Caution must be taken when cross zoning devices to ensure that the Cross Zone Time is long enough to

allow an intruder to trip both devices before it expires. A Cross Zone Time that is too short may allow an

intruder to trip the devices and allow only a zone fault report be sent to the central station.

When a Cross Zoned zone trips a FAULT report is sent to the SCS-1R Receiver. When two Cross Zoned zones

trip within the Cross Zone Time, both zones send ALARM signals to the receiver. For example, if zones 1

and 2 are Cross Zoned zones, and only zone 1 trips, a FAULT report is sent to the receiver for zone 1. If

zone 1 trips and zone 2 trips within the Cross Zone Time, an ALARM report is sent to the receiver for zone

1 and zone 2.

Report Type

Immediately Delayed

23.7 Events Manager

Alarm

Trouble

Restore

Opening

Closing

Bypass

Reset

Supervisory

Add Codes

The Events Manager allows you to delay sending

certain reports to the central station receiver.

Reports can be kept in the panel memory until

overwritten by new activity or held until the

memory buffer reaches 50 events or 50 door access

granted events. When the buffer is full, the panel

automatically sends the stored reports to the

central station receiver. The table lists the panel

reports you can delay using the Events Manager

option.

Delete Codes

Change Codes

Permanent Schedule Change

Temporary Schedule Change

Door Access

23.8 User Proﬁles

A proﬁle deﬁnes the authority of each user

code in the system. Proﬁles are programmed in

the Keypad User Menu. Several characteristics

associated with each User Proﬁle deﬁne its

authority within the system. To effectively

Door Access Denied

Late to Close

Force Armed Zone

program an XR500 Series system, you must understand the interrelationship between proﬁles, devices,

output groups, and areas. Below is a brief explanation of the User Proﬁle elements. For more information

about user proﬁles, refer to the User Proﬁles Record and the XR100/XR500 User’s Guide (LT-0683).

Note: Proﬁles cannot be changed via keypad in an All/Perimeter or Home/Sleep/Away system. Use the

default proﬁles 1 through 10.

Proﬁle Number - Each proﬁle may be assigned a unique number from 1 to 99.

Proﬁle Name - Each proﬁle may be assigned a 32-character name. The Proﬁle Number is the default name.

Area Number - Each proﬁle may be assigned speciﬁc areas of the system for arming and disarming.

When creating proﬁles 1 to 98, NO areas are assigned by default. The default for proﬁle 99 is ALL areas

assigned. Proﬁle 99 is preprogrammed in the system at the factory.

Access Area Number - Each proﬁle may be assigned door access area assignments. Default for proﬁle 1 to 98

is NO areas assigned. Default for proﬁle 99 is ALL areas assigned. Proﬁle 99 is preprogrammed at the factory.

Output Group Assignment - Each proﬁle may be assigned an output group number from 1 to 10. Default

for proﬁle 1 to 98 is NO output group assigned. Default for proﬁle 99 is output group 10. Your system may

by programmed to turn on an output group at certain keypads when door access occurs.

User Menu Assignments - Each user proﬁle may have any of the menus assigned to it as shown in the

following User Proﬁle Record. The User Proﬁle Record lists the user menu proﬁle assignments and the

system functions users are allowed to access based on the proﬁle numbers assigned to their codes.

Always make sure that at least one administrator in your system has a proﬁle with all authorities and

areas.

23.9 User Proﬁles Record

This User Proﬁles Record can be used as a tool when programming Devices, Proﬁles, Areas, and Output

Groups. Because these programming options are interrelated, use this sheet to plan the system before you

begin the installation and programming process.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

aPPendiX

Proﬁle

Arm/Disarm

Areas

Output

Access Areas Group

Proﬁle Name

1 2 3 4 A

23.10 FA Series Transmitter Information

A House ID Number is like an address for FA Series wireless transmitters so they know with which panel

they should be communicating. The House ID Number is based on the last two digits of the panel primary

account number.

Be sure that the primary panel account number is programmed before programming any wireless

transmitters. Because the House ID is based on the account number, entering or changing the primary

account number after programming the transmitters requires you to reprogram all of the transmitters.

Cross Talk

If you have more than one account within a ﬁve-mile radius, there is a possibility that “cross talk” can

occur. “Cross talk” is when transmitters communicate with multiple panels when the transmitters have

the same House ID. If you have two panels within a ﬁve-mile radius that use wireless zones, be sure that

the last two digits of the account numbers are not the same.

For example, ABC Plumbing has a panel with an account number of 12345 that uses wireless zones. The

House ID for the wireless transmitters at ABC Plumbing is 45. Two blocks away, XYZ Printing has an

account number of 22345 and the panel also uses wireless zones. The House ID for the transmitters for

XYZ Printing is 45. Because the two accounts have the same last two digits in the account numbers, the

House ID is the same. Therefore, the wireless transmitters “cross talk” and report to both panels bearing

the same House ID.

To avoid “cross talking”, panels within a ﬁve-mile radius must not have the same two digits in the primary

account number. If a “cross talk” issue is already present, you must delete the wireless transmitter zones,

enter the proper account numbers, and then reprogram the wireless transmitters.

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

aPPendiX

23.10.1Wireless Check-in and Supervision Deﬁnitions

FA Series Check-in Time Explained

The check-in time programmed for FA Series wireless transmitters is the number of seconds between

each message sent from the transmitter to the FA Series receiver for supervision purposes. This time is

programmable for each transmitter from 10, 30, or 60 seconds. Selecting 0 (zero) disables check-in. If no

messages are received from a transmitter in any four-hour period, a transmitter missing is generated by

the FA Series receiver and communicated to the panel.

DMP 1100 Series Supervision Time Explained

The supervision time programmed for DMP 1100 Series wireless is the number of minutes that must elapse

before a transmitter missing message is generated for a transmitter that is not sending its automatically

generated supervision message. The supervision time is programmable to 3, 60, 240 minutes. Selecting 0

(zero) disables supervision time.

23.11 Keypad Bus and LX-Bus Zone Type Descriptions

This section describes applications for the default Keypad and LX-Bus zone types in Zone Information

programming.

-- (Blank Zone)

Customizable zone type. By default, no actions are programmed to occur with Blank Zone. A zone name

must be entered to use this zone type: This zone type is not the same as an *UNUSED* zone.

NT (Night Zone)

Controlled instant zone used for perimeter doors and windows and interior devices such as PIRs and

Glassbreak detectors.

DY (Day zone)

Used for emergency doors or ﬁre doors to sound the keypad buzzer and display the zone name when the

zone is faulted. Day zones also send alarm reports to the receiver during the system armed periods.

EX (Exit zone)

Initiates the entry delay timer when its assigned area is fully armed. Also, can initiate an exit delay timer

to allow a user to exit an area after the arming process starts.

PN (Panic zone)

Used for connecting to mechanical devices that allow a user to signal an emergency alarm. Panic zones

can provide either a silent or audible alarm with or without reporting to a central station receiver.

EM (Emergency zone)

These are used for reporting medical or other non-panic emergencies to the central station receiver.

SV (Supervisory zone)

Used to provide 24-hour zone supervision to devices associated with ﬁre systems. Typical applications are

tamper switches on Post Indicator Valves (PIVs), gate valves, and low and high temperature gauges.

FI (Fire zone)

Used for any type of powered or mechanical ﬁre detection device. Typical applications are for smoke

detectors, sprinkler ﬂowswitches, manual pull stations, and beam detectors. Retard, cross zoning, and

presignal options are available for the Fire zone type.

FV (Fire Verify zone)

Used primarily for smoke detector circuits to verify the existence of an actual ﬁre condition. When a Fire

Verify zone initiates an alarm, the panel performs a Fire Reset. If any Fire Verify zone initiates an alarm

within 120 seconds after the reset, an alarm is indicated. If an alarm is initiated after 120 seconds, the

cycle repeats.

A1 and A2 (Auxiliary 1 and Auxiliary 2)

These zones are similar to a Night zone and are typically used to protect restricted areas within a

protected premises.

AR (Arming zone)

This zone allows you to connect a keyswitch to a zone and use it to arm and disarm one or more areas.

23.12 Zone Type Speciﬁcations

The XR500 Series Canadian panel contains multiple default zone types for use in conﬁguring the system.

These zone types provide the most commonly selected functions for their applications. All zone types

can be customized by changing the variable options listed below. The Keypad Bus Zone Information table

below reﬂects the zone types for Keypad Bus Zones. The XR500 Series LX-Bus Zone Information table on

the next page reﬂects the zone types for LX-Bus Zones.

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

aPPendiX

Keypad Bus Zone

Information

Type

Area Fire Disarmed Disarmed

Armed

Open

Armed

Short

Bell

Open

Short

Assign Disarm condition of

NT, DY, EX, A1, and A2 only

INT

PERIM

BDRM

-- NT

DY EX

FI PN

EM SV

A1 A2

FV AR

Assign Prewarn and Entry

Delay for EX only

Assign Retard and Presignal

for FI, SV, A1, and A2 only

TGL

ARM

DIS

STEP

MNT

N N

or to or or to or or or to or to

Zone Type Defaults

Y 16 Y 16

Night

Day

Exit

Fire

N N

1-16

Panic

Emergency

Supervisory

Auxiliary 1

Auxiliary 2

Fire Verify

Arming

TGL

*Output Options: 1 to 6, 450 to 474, 480 to 499, 500 to 999, D1 to D16, G1 to G20. + = Set retard to YES before selecting presignal.

= Zone functions not available.

23.12.1 Keypad Bus Zone Type Defaults

These are complete spellings of the abbreviations used for the zone types, such as Night and Exit.

Type - These are the abbreviations used for the zone types, such as NT and EX.

Area - For an Area or Home/Sleep/Away with Guest system this is 1 to 32. For an All/Perimeter or Home/

Sleep/Away system, this is the Interior, Bedroom, or Perimeter. Select the area for NT, DY, EX, A1, A2, and

AR types.

Fire Bell Out - Only available for FI, FV, and SV zones. Use any output zone number listed.

Message - A = alarm report, T = trouble report, L = local, no report, — (dash) = no report, D = door propped

(When SV zone is connected to 303 Silence/Reset Switch), S = sensor reset/alarm silence,

C = early morning ambush cancel.

Output - These are 1 to 6 on-board and 500 to 999 off-board relay outputs, 450 to 474 and 480 to 499

wireless outputs, D1 to D16, and G1 to G20.

Action - This selects the action of the output: S = steady, P = pulse, M = momentary, and F = follow

Swinger - The zone can be automatically shunted after a programmed number of trips.

Prewarn - This selects the keypad address that sounds the entry prewarn for this zone.

Entry Delay - This is the entry delay timer selected as the default for this zone.

Retard Delay - Provides a programmed retard time before an alarm initiates from a shorted zone. When

used on an arming zone, the retard delay occurs when the zone is shorted before the armed state has

changed. If the arming zone has Maintain as the Style, the retard delay also occurs when the zone returns

to a normal state.

Presignal - Provides a keypad tone for zones in retard delay. Retard must be YES before Presignal can be

selected.

Fast Response - Provides a 167ms zone response instead of the normal 500ms response.

Cross Zone - Provides cross zoning with any of the 574 zones.

Priority - Requires this zone to be in a normal condition before the area can be armed.

Style - The abbreviations for arming zone style:

TGL = Toggle, ARM = Arm only, DIS = Disarm only, STEP = Wireless arming, MNT = Maintain

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

aPPendiX

S t y l e

23.12.2 LX-Bus Zone Type Defaults

These are complete spellings of the abbreviations used for the

D o o r N u m b e r

zone types, such as Night and Exit.

e R p o r t s i m e e R a l - T

A r e a l l o F w o

r i P o r i t y

Type - These are the abbreviations used for the zone types,

such as NT and EX.

Z o n e C r o s s

e s p o n s F e a s t R

r e P s i g n a l

Area - For an Area or Home/Sleep/Away with Guest system

this is 1 to 32. For an All/Perimeter or Home/Sleep/Away

system, this is the Interior, Bedroom, or Perimeter. Select the

area for NT, DY, EX, A1, A2, and AR types.

e R t a r d D e l a y

E n t r y D e l a y

r e P w a r n

Fire Bell Out - Only available for FI, FV, and SV zones. Use

any output zone number listed.

S w i n g e r

A c t i o n

Wireless - This indicates wireless equipment is being used.

DMP Wireless - These options are for use with the DMP 1100X

Wireless Receiver.

O u t p u t

M e s s a g e

A c t i o n

FA Series Wireless - These options are for use with the

FA400-DMP Remote Wireless Receiver.

O u t p u t

M e s s a g e

Message - A = alarm report, T = trouble report,

L = local, no report, — (dash) = no report,

A c t i o n

D = door propped (When SV zone is connected to 303 Silence/

Reset Switch), S = sensor reset/alarm silence, C = early

morning ambush cancel.

O u t p u t

M e s s a g e

A c t i o n

Output - These are 1 to 6 on-board and 500 to 999 off-board

relay outputs, 450 to 474 and 480 to 499 wireless outputs, D1

to D16, and G1 to G20.

O u t p u t

M e s s a g e

Action - This selects the action of the output:

S = steady, P = pulse, M = momentary, and F = follow

O p e n

N o r m a l l y

E n d - o f - L i n e

C o n I N t a T c t

Swinger - The zone can be automatically shunted after a

programmed number of trips.

i m T e

C h e c k - i n

Prewarn - This selects the keypad address that sounds the

entry prewarn for this zone.

S e n s i t 1 i 1 v i 2 t 6 y

C o u n t P u l s e 1 1 2 6

D i s a b l e

Entry Delay - This is the entry delay timer selected as the

default for this zone.

D i s a r m 1 1 / 2 6

O p e r a t i o n

L E D 1 1 4 2

S u p e r v i s i o n

Retard Delay - Provides a programmed retard time before an

alarm initiates from a shorted zone. When used on an arming

zone, the retard delay occurs when the zone is shorted before

the armed state has changed. If the arming zone has Maintain

as the Style, the retard delay also occurs when the zone

returns to a normal state.

i m T e

1 1 1 4 C o n t a c t

N / O ?

C o n t a c t

1 1 0 1 E X T

1 1 0 1 C o n t a c t

i r e W l e s s

Presignal - Provides a keypad tone for zones in retard delay.

Retard must be YES before Presignal can be selected.

O u t p u t

Fast Response - Provides a 167ms zone response instead of the

normal 500ms response.

Cross Zone - Provides cross zoning with any of the 574 zones.

Priority - Requires this zone to be in a normal condition

before the area can be armed.

Style - The abbreviations for arming zone style:

TGL = Toggle, ARM = Arm only, DIS = Disarm only,

STEP = Wireless arming, MNT = Maint

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

aPPendiX

23.13 Common Keypad Messages

There are several common keypad messages that the keypad displays to inform the technician and

end-user. The common messages are described below. Possible solutions are also provided.

Message

Meaning

Possible Solutions

Change the user access areas if access to

the area is needed. If access is not needed,

the user cannot enter the area.

The user has attempted a door access for an

area they are not assigned.

INVALID AREA

The user code you entered is not recognized

by the system.

A user attempted a function that is outside of

the assigned proﬁle.

A user code assigned to a speciﬁc schedule has

entered outside of the valid schedule.

The area you are attempting to disarm or

access is a Two Man Area.

INVALID CODE

INVALID PROFILE

INVALID TIME

Check the user code and try again.

Check the user proﬁle settings.

See Schedules and User Codes.

A second and different user code must be

entered.

ENTER 2ND CODE

Users still on the premise should arm the

system or extend the schedule to a later

time.

Users still on the premise should arm the

system or extend the schedule to a later

time.

The scheduled has expired but the area is not

armed.

CLOSING TIME

LATE TO CLOSE

The system was not armed at its scheduled

closing time.

The user must exit the area through the

proper door. If not possible, your system

administrator should select the Forgive

option in the User Codes menu.

Check that all AC connections are good.

Check that the battery connections are good

and the battery is still good.

A user assigned the anti-passback option has

attempted to re-enter an area from which they

did not exit properly.

FAILED TO EXIT

AC TROUBLE

The system is not getting proper power.

The battery is either low or missing.

BATTERY TROUBLE

PHONE LINE 1

TROUBLE

There is trouble with the phone line

supervision.

Plug in the phone line.

Make sure the J16 jumper is removed from

the panel. Make sure there is not a short or

open condition on the green data wire to the

keypad. You may also need to check that all

of the keypads and expansion modules on

the bus are good.

SYSTEM TROUBLE or There is a problem with one or more

SERVICE REqUIRED

components in the system.

Wait a few moments for the system to

complete the task. Make sure the J16

jumper is not on the panel. If the message

displays for a long period of time, the

processor could be locked up.

Program a device to be supervised.

Make sure all wires are connected.

Program one of the devices to a unique

address.

Verify your communication type, account

number, and phone number. Make sure the

telephone line is connected and working

properly.

The system is performing another task with a

higher priority.

SYSTEM BUSY

There is not a supervised device on the bus.

There is low voltage or an open yellow wire.

4-WIRE BUS TROUBLE

TRANSMIT FAIL

Two devices share the same address.

The panel has attempted to communicate

with the central station 10 times and has not

succeeded.

NON-POLLED

ADDRESS

ENTER CODE (to

enter Programming)

The device is not set to DOOR, KEYPAD or

FIRE in Device Setup during programming.

A lockout code has been programmed for the

panel.

Program the device as DOOR, KEYPAD or

FIRE in Device Setup.

Enter the lockout code.

The panel is unable to communicate with the

wireless receiver.

The wireless receiver is missing.

Verify the receiver is properly connected to

the panel. Verify the correct House Code is

programmed in System Options.

WIRELESS TROUBLE

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

aPPendiX

23.14 Area Account Number Messages

XR500 systems send an area account number instead of the system account number with the following

panel messages/events based on the area assigned to the zone that initiated the alarm:

•

WARNING: Alarm Bell Silenced (S34)

Abort Signal Received (S45)

Cancel Signal Received (S49)

ALERT: System Recently Armed (S78)

ALERT: Exit Error (S80)

ALARM: Verify Signal Received (S96) (not currently sent on area arming systems)

The XR500 has always sent the area account number for the following messages:

•

Zone event messages for all non-24 hour zones assigned to an area

Arming

Disarming

The XR500 sends the following messages using the area account number based on the lowest area number

in Display Areas programming from the keypad being used:

•

User Code Add/Change/Delete

Door Access/Denied

User 1 Ambush and Early Morning Ambush

System Test Begin/End

Unauthorized Entry

Service Code and Service Request

The XR500 sends the following messages using the area account number based on the area number:

Late to Arm for area schedules

•

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Monitoring Products

reviSionS

Revisions to This Document

This section explains the changes made to this document during this revision. It lists the version, identiﬁes

the change(s) made, the related section number and heading, and a summary of the change.

Guide

Version Section Number and Heading

Quick Explanation of Changes

1.08

6.4 Access Areas

6.7 Strike Time

Added statement about door locking

Added device type information

6.8 Strike Delay

Added device type information

6.13 Door Real-Time Status

6.14 Send Door Forced Message

6.15 Program 734 Options

7 Remote Options

Added Door Real-Time Status prompt

Added Send Door Forced Message prompt

Added Program 734 Options prompts

Complete restructure and reorganization

Allow up to 16 characters

7.2 Remote Key

7.4 Allow Dialer Remote

7.5 Allow Network Remote

7.6 Allow Cellular Remote

7.7 Allow RS-232 Remote

7.8 Entré Connection

Added Allow Dialer Remote prompt

Added Allow Network remote prompts

Added Allow Cell Remote prompts

Added Allow RS-232 Remote prompt

Added Entré Connection prompts

19.30 Report with Acct Number for Area Added Report with Account Number for Area prompt

1.07

3.34 Send Path Information

5.4 Destination 1

Added Send Path Information section

Added TLS Encryption note

5.5 Destination 1 User Number

5.7 Destination 2 User Number

5.9 Destination 3 User Number

5.13 Monthly Limit

Added Destination 1 User Number section

Added Destination 2 User Number section

Added Destination 3 User Number section

Added Monthly Limit option

6.2 Device Number

Added new Device Types

6.3 Door Name

Added option of entering up to 32 characters

Added First/Second GPRS APN section

Added Send 16 Character Names option

Added option of entering up to 32 characters

Changed exit delay minimum from 45 to 30 seconds

Added option of entering up to 32 characters

Added Fire Panel Slave Input option

Added Zone Audit Days section

7.14 First/Second GPRS APN

9.23 Send 16 Character Names

12.3 Output Name

13.3 Group Name

18.2 Exit Delay

18.11 Area Name

19.3 Zone Name

19.26 Fire Panel Slave Input

19.29 Zone Audit Days

23.3 Using the 984 Command Function Changed Keypad to Test

23.8 User Proﬁles Added option of entering up to 32 characters

Digital Monitoring Products

XR500 Series Canadian Programming Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Listings and Approvals

This Class A digital apparatus complies with

Canadian ICES-003

NIST Validated XR500E Encrypted Command

Processor Panel Certificate #130

ANSI/SIA CP-01-2000 False Alarm Reduction

Underwriters Laboratories Canada (ULC) Listed

ULC S545

Household Fire

ULC Subject-C1023 Household Burglar

ULC/ORD-C1076

ULC S304-06

Proprietary Burglar

Central Station Burglar

800-641-4282

www.dmp.com

Made in the USA

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springfield, Missouri 65803-8877

Download from Www.Somanuals.com. All Manuals Search And Download.

Compaq CD Player PCD 1 User Manual
Crate Amplifiers Musical Instrument Amplifier GFX 120T User Manual
Crosley Refrigerator 241024401 User Manual
Crown Audio Music Mixer IQ USM 810 User Manual
Desa Stove SVYD18NRA PRA SERIES User Manual
DOD Carbon Monoxide Alarm PS 7 User Manual
ETA Systems Oxygen Equipment FC01 LQ User Manual
Fortinet Network Card FortiLog 100 User Manual
Franke Consumer Products Ventilation Hood FGL 6015 XS User Manual
GE Air Conditioner AZ75E09DAC User Manual