STK11C68
64 Kbit (8K x 8) SoftStore nvSRAM
Features
Functional Description
■
■
■
■
■
■
■
■
■
■
■
■
■
25 ns, 35 ns, and 45 ns access times
Pin compatible with industry standard SRAMs
Software initiated nonvolatile STORE
Unlimited Read and Write endurance
Automatic RECALL to SRAM on power up
Unlimited RECALL cycles
The Cypress STK11C68 is a 64Kb fast static RAM with a nonvol-
atile element in each memory cell. The embedded nonvolatile
elements incorporate QuantumTrap technology producing the
world’s most reliable nonvolatile memory. The SRAM provides
unlimited read and write cycles, while independent nonvolatile
data resides in the highly reliable QuantumTrap cell. Data
transfers under software control from SRAM to the nonvolatile
elements (the STORE operation). On power up, data is automat-
ically restored to the SRAM (the RECALL operation) from the
nonvolatile memory. RECALL operations are also available
under software control.
1,000,000 STORE cycles
100 year data retention
Single 5V+10% operation
Commercial and industrial temperature
28-pin (330 mil) SOIC package
28-pin (300 mil) CDIP and 28-pad (350 mil) LCC packages
RoHS compliance
Logic Block Diagram
V
CC
V
CAP
Quantum Trap
128 X 512
A5
POWER
STORE
CONTROL
A6
A7
A8
RECALL
STORE/
RECALL
CONTROL
STATIC RAM
ARRAY
128 X 512
HSB
A9
A11
A12
SOFTWARE
DETECT
A0
-
A12
DQ0
COLUMN I/O
DQ1
DQ2
DQ3
COLUMN DEC
DQ4
DQ5
DQ6
DQ7
A0
A4
A10
A1
A3
A2
OE
CE
WE
Cypress Semiconductor Corporation
Document Number: 001-50638 Rev. **
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised January 30, 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
not necessary that OE is LOW for a valid sequence. After the
tSTORE cycle time is fulfilled, the SRAM is again activated for
Read and Write operation.
Device Operation
The STK11C68 is a versatile memory chip that provides several
modes of operation. The STK16C88 can operate as a standard
8K x 8 SRAM. A 8K x 8 array of nonvolatile storage elements
shadow the SRAM. SRAM data can be copied nonvolatile
memory or nonvolatile data can be recalled to the SRAM.
Software RECALL
Data is transferred from the nonvolatile memory to the SRAM by
a software address sequence. A software RECALL cycle is
initiated with a sequence of Read operations in a manner similar
to the software STORE initiation. To initiate the RECALL cycle,
the following sequence of CE controlled Read operations is
performed:
SRAM Read
The STK11C68 performs a Read cycle whenever CE and OE are
LOW while WE is HIGH. The address specified on pins A0–12
determines the 8,192 data bytes accessed. When the Read is
initiated by an address transition, the outputs are valid after a
delay of tAA (Read cycle 1). If the Read is initiated by CE or OE,
the outputs are valid at tACE or at tDOE, whichever is later (Read
cycle 2). The data outputs repeatedly respond to address
changes within the tAA access time without the need for transi-
tions on any control input pins, and remains valid until another
address change or until CE or OE is brought HIGH, or WE
brought LOW.
1. Read address 0x0000, Valid READ
2. Read address 0x1555, Valid READ
3. Read address 0x0AAA, Valid READ
4. Read address 0x1FFF, Valid READ
5. Read address 0x10F0, Valid READ
6. Read address 0x0F0E, Initiate RECALL cycle
Internally, RECALL is a two step procedure. First, the SRAM data
is cleared; then, the nonvolatile information is transferred into the
SRAM cells. After the tRECALL cycle time, the SRAM is again
ready for Read and Write operations. The RECALL operation
does not alter the data in the nonvolatile elements. The nonvol-
atile data can be recalled an unlimited number of times.
SRAM Write
A Write cycle is performed whenever CE and WE are LOW. The
address inputs must be stable prior to entering the Write cycle
and must remain stable until either CE or WE goes HIGH at the
end of the cycle. The data on the common IO pins DQ0–7 are
written into the memory if it has valid tSD, before the end of a WE
controlled Write or before the end of an CE controlled Write.
Keep OE HIGH during the entire Write cycle to avoid data bus
contention on common IO lines. If OE is left LOW, internal
circuitry turns off the output buffers tHZWE after WE goes LOW.
Hardware RECALL (Power Up)
During power up or after any low power condition (VCC
<
V
RESET), an internal RECALL request is latched. When VCC
once again exceeds the sense voltage of VSWITCH, a RECALL
cycle is automatically initiated and takes tHRECALL to complete.
If the STK11C68 is in a Write state at the end of power up
RECALL, the SRAM data is corrupted. To help avoid this
situation, a 10 Kohm resistor is connected either between WE
Software STORE
Data is transferred from the SRAM to the nonvolatile memory by
a software address sequence. The STK11C68 software STORE
cycle is initiated by executing sequential CE controlled Read
cycles from six specific address locations in exact order. During
the STORE cycle, an erase of the previous nonvolatile data is
first performed followed by a program of the nonvolatile
elements. When a STORE cycle is initiated, input and output are
disabled until the cycle is completed.
and system VCC or between CE and system VCC
.
Hardware Protect
The STK11C68 offers hardware protection against inadvertent
STORE operation and SRAM Writes during low voltage condi-
tions. When VCAP<VSWITCH, all externally initiated STORE
operations and SRAM Writes are inhibited.
Because a sequence of Reads from specific addresses is used
for STORE initiation, it is important that no other Read or Write
accesses intervene in the sequence. If they intervene, the
sequence is aborted and no STORE or RECALL takes place.
Noise Considerations
The STK11C68 is a high speed memory. It must have a high
frequency bypass capacitor of approximately 0.1 µF connected
between VCC and VSS, using leads and traces that are as short
as possible. As with all high speed CMOS ICs, careful routing of
power, ground, and signals reduce circuit noise.
To initiate the software STORE cycle, the following Read
sequence is performed:
1. Read address 0x0000, Valid READ
2. Read address 0x1555, Valid READ
3. Read address 0x0AAA, Valid READ
4. Read address 0x1FFF, Valid READ
5. Read address 0x10F0, Valid READ
6. Read address 0x0F0F, Initiate STORE cycle
Low Average Active Power
CMOS technology provides the STK11C68 the benefit of
drawing significantly less current when it is cycled at times longer
shown for both CMOS and TTL input levels (commercial temper-
ature range, VCC = 5.5V, 100% duty cycle on chip enable). Only
standby current is drawn when the chip is disabled. The overall
The software sequence is clocked with CE controlled Reads.
When the sixth address in the sequence is entered, the STORE
cycle commences and the chip is disabled. It is important that
Read cycles and not Write cycles are used in the sequence. It is
Document Number: 001-50638 Rev. **
Page 3 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
average current drawn by the STK11C68 depends on the
following items:
Best Practices
nvSRAM products have been used effectively for over 15 years.
While ease of use is one of the product’s main system values,
experience gained working with hundreds of applications has
resulted in the following suggestions as best practices:
■
■
■
■
■
■
■
The duty cycle of chip enable
The overall cycle rate for accesses
The ratio of Reads to Writes
CMOS versus TTL input levels
The operating temperature
The VCC level
■
The nonvolatile cells in an nvSRAM are programmed on the
test floor during final test and quality assurance. Incoming
inspection routines at customer or contract manufacturer’s
sites sometimes reprograms these values. Final NV patterns
are typically repeating patterns of AA, 55, 00, FF, A5, or 5A.
Theendproduct’sfirmwareshouldnotassumethatanNVarray
is in a set programmed state. Routines that check memory
content values to determine first time system configuration,
IO loading
Figure 2. Current Versus Cycle Time (Read)
■
■
cold or warm boot status, and so on must always program a
unique NV pattern (for example, complex 4-byte pattern of 46
E6 49 53 hex or more random bytes) as part of the final system
manufacturing test to ensure these system routines work
consistently.
Power up boot firmware routines should rewrite the nvSRAM
into the desired state. While the nvSRAM is shipped in a preset
state, best practice is to again rewrite the nvSRAM into the
desired state as a safeguard against events that might flip the
bit inadvertently (program bugs, incoming inspection routines,
and so on).
Figure 3. Current Versus Cycle Time (Write)
Table 1. Hardware Mode Selection
CE
WE
A12–A0
Mode
IO
Notes
[1]
L
H
0x0000
0x1555
0x0AAA
0x1FFF
0x10F0
0x0F0F
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Output Data
Output Data
Output Data
Output Data
Output Data
Output High Z
Nonvolatile STORE
[1]
L
H
0x0000
0x1555
0x0AAA
0x1FFF
0x10F0
0x0F0E
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Output Data
Output Data
Output Data
Output Data
Output Data
Output High Z
Nonvolatile RECALL
Note
1. The six consecutive addresses must be in the order listed. WE must be high during all six consecutive CE controlled cycles to enable a nonvolatile cycle.
Document Number: 001-50638 Rev. **
Page 4 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
Power Dissipation ......................................................... 1.0W
DC Output Current (1 output at a time, 1s duration).... 15 mA
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. These user guidelines are not tested.
Operating Range
Storage Temperature ................................. –65°C to +150°C
Temperature under bias.............................. –55°C to +125°C
Supply Voltage on VCC Relative to GND ..........–0.5V to 7.0V
Voltage on Input Relative to Vss............–0.6V to VCC + 0.5V
Voltage on DQ0-7 ...................................–0.5V to Vcc + 0.5V
Ambient
Range
VCC
Temperature
0°C to +70°C
-40°C to +85°C
Commercial
Industrial
4.5V to 5.5V
4.5V to 5.5V
DC Electrical Characteristics
Over the operating range (VCC = 4.5V to 5.5V)
Parameter
ICC1
Description
Test Conditions
Min
Max
Unit
Average VCC Current tRC = 25 ns
Commercial
90
75
65
mA
mA
mA
t
t
RC = 35 ns
RC = 45 ns
Dependent on output loading and cycle rate.
Values obtained without output loads.
Industrial
90
75
65
mA
mA
mA
IOUT = 0 mA.
ICC2
ICC3
Average VCC Current All Inputs Do Not Care, VCC = Max
during STORE Average current for duration tSTORE
3
mA
Average VCC Current at WE > (VCC – 0.2V). All other inputs cycling.
tRC= 200 ns, 5V, 25°C Dependent on output loading and cycle rate. Values obtained
10
mA
Typical
without output loads.
[2]
ISB1
VCC Standby Current
(Standby, Cycling TTL tRC = 35 ns, CE > VIH
Input Levels)
tRC = 25 ns, CE > VIH
Commercial
Industrial
27
23
20
mA
mA
mA
tRC = 45 ns, CE > VIH
28
24
21
mA
mA
mA
[2]
ISB2
VCC Standby Current
CE > (VCC – 0.2V). All others VIN < 0.2V or > Commercial
(VCC – 0.2V). Standby current level after
750
μA
nonvolatile cycle is complete.
Inputs are static. f = 0 MHz.
Industrial
1500
μA
IIX
Input Leakage Current VCC = Max, VSS < VIN < VCC
-1
-5
+1
+5
μA
μA
IOZ
Off State Output
Leakage Current
VCC = Max, VSS < VIN < VCC, CE or OE > VIH or WE < VIL
VIH
Input HIGH Voltage
2.2
VCC
0.5
+
V
VIL
Input LOW Voltage
VSS – 0.5
2.4
0.8
V
V
V
VOH
VOL
Output HIGH Voltage IOUT = –4 mA
Output LOW Voltage
IOUT = 8 mA
0.4
Data Retention and Endurance
Parameter
Description
Min
100
Unit
DATAR
NVC
Data Retention
Years
K
Nonvolatile STORE Operations
1,000
Note
2. CE > V does not produce standby current levels until any nonvolatile cycle in progress has timed out.
IH
Document Number: 001-50638 Rev. **
Page 5 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
Capacitance
Parameter
CIN
COUT
Description
Input Capacitance
Output Capacitance
Test Conditions
Max
8
Unit
pF
TA = 25°C, f = 1 MHz,
CC = 0 to 3.0V
V
7
pF
Thermal Resistance
In the following table, the thermal resistance parameters are listed.[3]
Parameter
Description
Test Conditions
28-SOIC 28-CDIP 28-LCC Unit
ΘJA
Thermal Resistance
(Junction to Ambient)
Test conditions follow standard test methods
and procedures for measuring thermal
impedance, per EIA / JESD51.
TBD
TBD
TBD
°C/W
ΘJC
Thermal Resistance
(Junction to Case)
TBD
TBD
TBD
°C/W
Figure 4. AC Test Loads
R1 480Ω
5.0V
Output
R2
30 pF
255Ω
AC Test Conditions
Input Pulse Levels....................................................0V to 3V
Input Rise and Fall Times (10% to 90%)...................... <5 ns
Input and Output Timing Reference Levels.................... 1.5V
Note
3. These parameters are guaranteed by design and are not tested.
Document Number: 001-50638 Rev. **
Page 6 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
AC Switching Characteristics
SRAM Read Cycle
Parameter
25 ns
35 ns
45 ns
Unit
Description
Cypress
Alt
Min
Max
Min
Max
Min
Max
Parameter
tACE
tELQV
tAVAV, ELEH
tAVQV
Chip Enable Access Time
Read Cycle Time
25
35
45
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tRC
t
25
35
45
[5]
tAA
tDOE
Address Access Time
25
10
35
15
45
20
tGLQV
Output Enable to Data Valid
Output Hold After Address Change
Chip Enable to Output Active
Chip Disable to Output Inactive
Output Enable to Output Active
Output Disable to Output Inactive
Chip Enable to Power Active
Chip Disable to Power Standby
[5]
tOHA
tAXQX
5
5
5
5
5
5
[6]
[6]
[6]
[6]
tLZCE
tHZCE
tLZOE
tHZOE
tELQX
tEHQZ
10
10
25
13
13
35
15
15
45
tGLQX
0
0
0
0
0
0
tGHQZ
[3]
tPU
tELICCH
tEHICCL
[3]
tPD
Switching Waveforms
W5&
$''5(66
W$$
W2+$
'4ꢌꢊ'$7$ꢌ287ꢋ
'$7$ꢌ9$/,'
W5&
$''5(66
&(
W$&(
W3'
W+=&(
W/=&(
2(
W+=2(
W'2(
W/=2(
'4ꢌꢊ'$7$ꢌ287ꢋ
'$7$ꢌ9$/,'
$&7,9(
W38
67$1'%<
,&&
Notes
4. WE must be High during SRAM Read cycles.
5. I/O state assumes CE and OE < V and WE > V ; device is continuously selected.
IL
IH
6. Measured ±200 mV from steady state output voltage.
Document Number: 001-50638 Rev. **
Page 7 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
SRAM Write Cycle
Parameter
25 ns
35 ns
45 ns
Unit
Description
Write Cycle Time
Cypress
Parameter
Alt
Min
Max
Min
Max
Min
Max
tWC
tAVAV
tWLWH, WLEH
tELWH, ELEH
tDVWH, DVEH
tWHDX, EHDX
tAVWH, AVEH
tAVWL, AVEL
tWHAX, EHAX
tWLQZ
tWHQX
25
20
20
10
0
35
25
25
12
0
45
30
30
15
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tPWE
tSCE
tSD
t
Write Pulse Width
t
Chip Enable To End of Write
Data Setup to End of Write
Data Hold After End of Write
Address Setup to End of Write
Address Setup to Start of Write
Address Hold After End of Write
Write Enable to Output Disable
Output Active After End of Write
t
tHD
t
tAW
t
20
0
25
0
30
0
tSA
t
tHA
t
0
0
0
tHZWE
tLZWE
10
13
15
5
5
5
Switching Waveforms
tWC
ADDRESS
CE
tHA
tSCE
tAW
tSA
tPWE
WE
tHD
tSD
DATA VALID
DATA IN
tHZWE
tLZWE
HIGH IMPEDANCE
PREVIOUS DATA
DATA OUT
tWC
ADDRESS
tHA
tSCE
tSA
CE
WE
tAW
tPWE
tSD
tHD
DATA IN
DATA VALID
HIGH IMPEDANCE
DATA OUT
Notes
7. If WE is Low when CE goes Low, the outputs remain in the high impedance state.
8.
CE or WE must be greater than V during address transitions.
IH
Document Number: 001-50638 Rev. **
Page 8 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
AutoStore INHIBIT or Power Up RECALL
STK11C68
Max
Parameter
Alt
Description
Unit
Min
[9]
tHRECALL
tRESTORE
tHLHZ
Power up RECALL Duration
STORE Cycle Duration
550
10
μs
ms
V
tSTORE
VSWITCH
VRESET
Low Voltage Trigger Level
Low Voltage Reset Level
4.0
4.5
3.6
V
Switching Waveform
Figure 9. AutoStore INHIBIT/Power Up RECALL
VCC
5V
VSWITCH
VRESET
STORE INHIBIT
POWER-UP RECALL
t
HRECALL
DQ (DATA OUT)
POWER-UP
RECALL
BROWN OUT
STORE INHIBIT
BROWN OUT
STORE INHIBIT
BROWN OUT
STORE INHIBIT
NO RECALL
NO RECALL
RECALL WHEN
(V DID NOT GO
(V DID NOT GO
V
RETURNS
CC
CC
CC
BELOW V
)
BELOW V
)
ABOVE V
RESET
RESET
SWITCH
Note
9.
t
starts from the time V rises above V
.
SWITCH
HRECALL
CC
Document Number: 001-50638 Rev. **
Page 9 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
Software Controlled STORE/RECALL Cycle
25 ns
35 ns
45 ns
Unit
Parameter
tRC
Alt
Description
Min
Max
Min
Max
Min
Max
tAVAV
tAVEL
tELEH
tELAX
STORE/RECALL Initiation Cycle Time
Address Setup Time
25
0
35
0
45
0
ns
ns
ns
ns
μs
[10]
tSA
tCW
Clock Pulse Width
20
20
25
20
30
20
[10]
tHACE
Address Hold Time
tRECALL
RECALL Duration
20
20
20
Switching Waveform
tRC
tRC
ADDRESS # 1
ADDRESS # 6
ADDRESS
tSA
tSCE
CE
tHACE
OE
t
STORE / tRECALL
HIGH IMPEDANCE
DATA VALID
DATA VALID
DQ (DATA)
Notes
10. The software sequence is clocked on the falling edge of CE without involving OE (double clocking aborts the sequence).
11. The six consecutive addresses must be read in the order listed in Table 1 on page 4. WE must be HIGH during all six consecutive cycles.
Document Number: 001-50638 Rev. **
Page 10 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
Part Numbering Nomenclature
STK11C68 - S F 45 I TR
Packaging Option:
TR = Tape and Reel
Blank = Tube
Temperature Range:
Blank - Commercial (0 to 70°C)
I - Industrial (-40 to 85°C)
Speed:
25 - 25 ns
35 - 35 ns
45 - 45 ns
Lead Finish
F = 100% Sn (Matte Tin)
Package:
S = Plastic 28-pin 330 mil SOIC
C = Ceramic 28-pin 300 mil DIP
L = Ceramic 28-pin 350 mil LLC
Ordering Information
Speed (ns)
Ordering Code
STK11C68-SF25TR
STK11C68-SF25
STK11C68-SF25ITR
STK11C68-SF25I
STK11C68-SF35TR
STK11C68-SF35
STK11C68-C35
Package Diagram
001-85058
001-85058
001-85058
001-85058
001-85058
001-85058
001-51695
001-51696
001-85058
001-85058
001-51695
001-51696
Package Type
28-Pin SOIC (330 mil)
28-Pin SOIC (330 mil)
28-Pin SOIC (330 mil)
28-Pin SOIC (330 mil)
28-Pin SOIC (330 mil)
28-Pin SOIC (330 mil)
28-Pin CDIP (300 mil)
28-Pin LCC (350 mil)
28-Pin SOIC (330 mil)
28-Pin SOIC (330 mil)
28-Pin CDIP (300 mil)
28-Pin LCC (350 mil)
Operating Range
25
Commercial
Industrial
35
Commercial
STK11C68-L35
STK11C68-SF35ITR
STK11C68-SF35I
STK11C68-C35I
Industrial
STK11C68-L35I
Document Number: 001-50638 Rev. **
Page 11 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
Ordering Information (continued)
Speed (ns)
Ordering Code
STK11C68-SF45TR
STK11C68-SF45
STK11C68-C45
Package Diagram
001-85058
001-85058
001-51695
001-51696
001-85058
001-85058
001-51695
001-51696
Package Type
28-Pin SOIC (330 mil)
28-Pin SOIC (330 mil)
28-Pin CDIP (300 mil)
28-Pin LCC (350 mil)
28-Pin SOIC (330 mil)
28-Pin SOIC (330 mil)
28-Pin CDIP (300 mil)
28-Pin LCC (350 mil)
Operating Range
Commercial
45
STK11C68-L45
STK11C68-SF45ITR
STK11C68-SF45I
STK11C68-C45I
STK11C68-L45I
Industrial
All parts are Pb-free. The above table contains Final information. Contact your local Cypress sales representative for availability of these parts
Document Number: 001-50638 Rev. **
Page 12 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
Package Diagrams
Figure 11. 28-Pin (330 Mil) SOIC (51-85058)
51-85058 *A
Document Number: 001-50638 Rev. **
Page 13 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
Package Diagrams (continued)
Figure 12. 28-Pin (300 Mil) Side Braze DIL (001-51695)
001-51695 **
Document Number: 001-50638 Rev. **
Page 14 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
Package Diagrams (continued)
Figure 13. 28-Pad (350 Mil) LCC (001-51696)
1. ALL DIMENSION ARE IN INCHES AND MILLIMETERS [MIN/MAX]
2. JEDEC 95 OUTLINE# MO-041
001-51696 **
3. PACKAGE WEIGHT : TBD
Document Number: 001-50638 Rev. **
Page 15 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STK11C68
Document History Page
Document Title: STK11C68 64 Kbit (8K x 8) SoftStore nvSRAM
Document Number: 001-50638
Orig. of
Change
Submission
Date
Rev.
ECN No.
Description of Change
**
2625084
GVCH/PYRS
01/30/09
New data sheet
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC
PSoC Solutions
General
Clocks & Buffers
Wireless
Low Power/Low Voltage
Precision Analog
LCD Drive
Memories
Image Sensors
CAN 2.0b
USB
© Cypress Semiconductor Corporation, 2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any
circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical,
life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical
components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-50638 Rev. **
Revised January 30, 2009
Page 16 of 16
AutoStore and QuantumTrap are registered trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective
holders.
Download from Www.Somanuals.com. All Manuals Search And Download.
|