XT10
Guitar Amplifier
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
XT10 Guitar Amplifier
1
2
3
4
5
6
7
8
9
10
11
1: INPUT: Use this jack to connect your instrument to
the amplifier by means of a shielded instrument cable.
12: AC LINE IN: (Rear panel, not shown) The ground-
ed power cord should only be plugged into a grounded
power outlet that meets all applicable electrical codes
and is compatible with the voltage, power, and frequen-
cy requirements stated on the rear panel. Do not
attempt to defeat the safety ground connection.
Getting Your Sound: The Level, Gain and Master
Level controls (#2, 3 & 4) can be used together to cre-
ate a wide variety of sounds. The following guidelines
will help you achieve your desired sound.
Clean Sounds: Set the Gain control to “OFF” (fully
counterclockwise position). Use the Master Level con-
trol to set the output level.
“Crunch” Sounds: Set the Level control to 11 o’clock
and the Gain to 9 o’clock. Use the Master Level control
to set the output level. (The Master Level control should
be adjusted to a lower setting as the Level and Gain
controls are increased.)
2: OD LEVEL: Use this control to increase the volume
and add “crunch” to your sound. This control is only
active when the OD Gain control (#3) is turned on. (For
more information please see the section entitled
“Getting Your Sound.”)
3: OD GAIN: Use this control in conjunction with the OD
Level control (#2) to add distortion to your sound. (For
more information please see the section entitled
“Getting Your Sound.”) At the fully counterclockwise
position the OD channel is turned off.
4: CLEAN MASTER LEVEL: Use this control to set the
overall output level of the amp. (For more information
please see the section entitled “Getting Your Sound.”)
5: EQ LOW: Use this control to adjust the output level of
the low frequencies. Rotating this control counterclock-
wise reduces the low frequency output; rotating it clock-
wise increases it.
Rhythm Sounds: Set the Level control around 11
o’clock and the Gain at or near “10”. Use the Master
Level control to set the output level.
Lead Sounds: Set the Level and Gain controls at or near
“10”. Use the Master Level control to set the output level.
6: EQ MID: Use this control to adjust the output level of
the midrange frequencies. Rotating this control counter-
clockwise reduces the midrange frequency output; rotat-
ing it clockwise increases it.
7: EQ HIGH: Use this control to adjust the output level
of the high frequencies. Rotating this control counter-
clockwise reduces the high frequency output; rotating it
clockwise increases it.
Connecting to the Insert Jack: Use Crate’s STP201,
STP202 or STP203 stereo-to-mono Y-cord or an
adapter such as Crate’s YPP117 and 2 1/4” mono sig-
nal cables to connect to the effect as shown:
Stereo-to-mono Y-cord:
Y-adapter and 2 cables:
8: INSERT: Use this jack to connect an external effects
to the amplifier. Use a stereo 1/4” male Y-cord: ring =
send, tip = return, sleeve = ground. Send goes to the
effect’s input; return comes from its output. (For more
information please see the section entitled “Connecting
to the Insert Jack.”)
TIP
RETURN
TIP
RING
SLEEVE
to Insert
jack
to Insert
jack
RING
SLEEVE
SEND
GROUND
(STP201, 3'
STP202, 6'
STP203, 9')
(YPP117)
9:
(HEADPHONES): Use this jack to connect a pair
of stereo headphones for private listening. The internal
speaker is disconnected when headphones are in use.
(1/4"-TO-1/4"
MONO SHIELDED
CABLES)
10: ON: This LED illuminates when power is applied to
the amplifier.
11: POWER: Use this switch to turn the amplifier on and
to
to
effect
"IN"
to
to
effect
"IN"
effect
"OUT"
jack
effect
"OUT"
jack
jack
jack
off.
External Effect
External Effect
Download from Www.Somanuals.com. All Manuals Search And Download.
XT10 Guitar Amplifier
XT10 TECHNICAL SPECIFICATIONS:
Output Power Rating
10W RMS @ 1% THD, 4Ω, 120 VAC
14W @ 10% THD
Speaker Size
6”
Input Impedance
Minimum Noise
Maximum Noise
Distortion
500k ohms
1mV
10mV
9%
Power Requirements
120 VAC, 60Hz, 20VA
100/115VAC, 50/60Hz, 20VA
230VAC, 50/60Hz, 20VA
Size and Weight
14” H x 12-1/2” W x 6” D, 12 lbs.
SYSTEM BLOCK DIAGRAM:
OD
BUFFER
EQ
PRE AMP
INSERT
INPUT
Master
Level
TIP: RETURN
RING: SEND
High Mid Low
Level Gain
POWER AMP
HEADPHONE
AC POWER
POWER SUPPLY
B+
B–
POWER LED
SPEAKER
POWER SW
The XT10 is covered with a durable Tolex material: wipe it clean with a lint-free cloth.
Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish.
Crate continually develops new products, as well as improves existing ones. For this reason, the specifications
and information in this manual are subject to change without notice.
©2004 SLM Electronics, a division of St. Louis Music, Inc • 1400 Ferguson Avenue • St. Louis, MO 63133
18-489-03 • 091504
Download from Www.Somanuals.com. All Manuals Search And Download.
|