CyberData Portable Speaker SPA 9000 User Manual

Setting Up the CyberData Speakers  
with Linksys SPA-9000  
1.0 Setting Up the Linksys SPA-9000  
To set up the Linksys SPA-9000:  
1.1 Run a Cat 5 cable from a POE/Ethernet hub to the Internet port
1.2 Run a second Cat 5 cable from a PoE/Ethernet hub to the EthA-9000.  
1.3 Plug in a computer/laptop, a Linksys phone, and a CybePoE/Ethernet  
hub.  
1.4 Adjust the IP address of the computer/laptop so thtwork as the SPA-9000  
(192.168.0.X).  
1.5 Enter the IP address of SPA-9000 in a browse/voice/advanced).  
1.6 Under Voice click on the SIP tab.  
1.7 In the PBX parameters section, selec
1.8 Click on submit all changes.  
1.9 Click on the Router tab.  
1.10 Click on the WAN Setu
1.11 From the Connectimenu, select Static IP.  
1.12 In the Static IP address, Netmask and Gateway fields.  
1.13 Go to Routset an IP address that is on a different subnet than the WAN  
address.  
1.14 Selec
2.0 Setting peaker for SIP  
ker for SIP:  
he web-based configuration for the speaker and click on SIP settings.  
r the username (usually an extension number) and password.  
Enter the static IP address that is in the WAN setup of the SPA-9000 as the SIP server address.  
2.4 Change the remote SIP port to 6060.  
2.5 Save the settings and reboot the speaker.  
2.6 Send a page to the speaker by entering the extension number (username) of the speaker at the  
dial-tone.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
3.9 Select page groups as the page target (see Figure 2).  
Figure 2. Linksys—Multicast Diagram  
4.0 Setting up tServer  
To set u
4.g the CyberData Paging Server product to CyberData speakers so that you  
an one paging zone (Figure 3), complete step 1.1 through step 1.13.  
b configuration page for the Paging Server and set it up as a SIP endpoint with the  
ame (extension number)  
ssword (make sure this matches what you have in step 2.2)  
SIP server address (step 1.5).Multicast address and port number combination  
DTMF two digit tone for each paging zone  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Figure 3. Linksys—Paging Server Diagram  
4.3 Go to the wee speaker and select MGROUPS.  
4.4 In the M, match the multicast address and port number combination that  
you pur for the paging zone that you want for the speaker.  
4.5 Diextension from the SIP phone.  
Not DTMF tone for the paging zone and initiate the page.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Compaq All in One Printer 9200c User Manual
Conair Hair Clippers IB 9 344 User Manual
Cradlepoint Network Router CTR350 User Manual
Dynacord Speaker System VL 152 User Manual
Dynasty Spas Hot Tub 9919 100578 B User Manual
Electro Voice Stereo Receiver NetMax N8000 User Manual
Fisher Paykel Oven 541024 D User Manual
Garmin Electric Heater 675 User Manual
GCC Printers Printer Elite 12ppm User Manual
GE Network Card 1018959 User Manual