Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
OperatOr’s Manual
Model Series CS 2210
Chipper Shredder — Model Series CS 2210 & CS 3310
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-08971
(April 19, 2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safe Operation Practices
2
WARNING: This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
CALIFORNIA PROPOSITION 65
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet and throwing debris. Failure to observe the following safety instructions could
result in serious injury or death.
8.
Never attempt to unclog either the feed intake or discharge
opening, remove or empty bag, or inspect and repair the
machine while the engine is running. Shut the engine off
and wait until all moving parts have come to a complete
stop. Disconnect the spark plug wire and ground it against
the engine.
Training
1.
Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
Preparation
2.
Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
1.
2.
3.
Thoroughly inspect the area where the equipment is to
be used. Remove all rocks, bottles, cans, or other foreign
objects which could be picked up or thrown and cause
personal injury or damage to the machine.
3.
Never allow children under 16 years of age to operate this
machine. Children 16 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and be trained and supervised by an
adult.
Always wear safety glasses or safety goggles during
operation and while performing an adjustment or repair,
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
4.
5.
Never allow adults to operate this machine without proper
instruction.
Wear sturdy, rough-soled work shoes and close-fitting
slacks and shirts. Loose fitting clothes or jewelry can be
caught in movable parts. Never operate this machine
in bare feet or sandals. Wear leather work gloves when
feeding material in the chipper chute.
Keep bystanders, pets, and children at least 75 feet from
the machine while it is in operation. Stop machine if
anyone enters the area.
6.
7.
Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
4.
5.
Before starting, check all bolts and screws for proper
tightness to be sure the machine is in safe working
condition. Also, visually inspect machine for any damage at
frequent intervals.
Do not put hands and feet near rotating parts or in the
feeding chambers and discharge opening. Contact with
the rotating impeller can amputate fingers, hands, and
feet.
Maintain or replace safety and instructions labels, as
necessary.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
5.
If it becomes necessary to push material through the
shredder hopper, use a small diameter stick. Do not use
your hands or feet.
Safe Handling of Gasoline:
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
If the impeller strikes a foreign object or if your machine
should start making an unusual noise or vibration,
immediately shut the engine off. Allow the impeller to
come to a complete stop. Disconnect the spark plug wire,
ground it against the engine and perform the following
steps:
a. Use only an approved gasoline container.
b. Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
a. Inspect for damage.
b. Repair or replace any damaged parts.
c. Check for any loose parts and tighten to assure
continued safe operation.
c. When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the ground.
If this is not possible, then refuel such equipment on
a trailer with a portable container, rather than from a
gasoline dispenser nozzle.
6.
Do not allow an accumulation of processed material to
build up in the discharge area. This can prevent proper
discharge and result in kickback of material through the
feed opening.
d. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
7.
Do not attempt to shred or chip material larger than
specified on the machine or in this manual. Personal injury
or machine damage could result.
e. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
8.
Never attempt to unclog either the feed intake or discharge
opening while the engine is running. Shut the engine off,
wait until all moving parts have stopped, disconnect the
spark plug wire and ground it against the engine before
clearing debris.
f.
Never fuel machine indoors.
g. Never remove gas cap or add fuel while the engine
is hot or running. Allow engine to cool at least two
minutes before refueling.
9.
Never operate without the shredder hopper, chipper chute,
or chute deflector properly attached to the machine.
Never empty or change discharge bag while the engine is
running.
h. Never over fill fuel tank. Fill tank to no more than ½
inch below bottom of filler neck to allow space for
fuel expansion.
i.
j.
Replace gasoline cap and tighten securely.
10. Keep all guards, deflectors and safety devices in place and
If gasoline is spilled, wipe it off the engine and
equipment. Move unit to another area. Wait 5
minutes before starting the engine.
operating properly.
11. Keep your face and body back and to the side of the
chipper chute while feeding material into the machine to
avoid accidental kickback injuries.
k. To reduce fire hazards, keep machine free of grass,
leaves, or other debris build-up. Clean up oil or fuel
spillage and remove any fuel soaked debris.
12. Never operate this machine without good visibility or light.
13. Do not operate this machine on a paved, gravel or non-
l.
Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
as on a water heater, space heater, furnace, clothes
dryer or other gas appliances.
level surface.
14. Do not operate this machine while under the influence of
alcohol or drugs.
15. Muffler and engine become hot and can cause a burn. Do
Operation
not touch.
1.
Do not put hands and feet near rotating parts or in the
feeding chambers and discharge opening. Contact with
the rotating impeller can amputate fingers, hands, and
feet.
16. Never pick up or carry machine while the engine is running.
17. If situations occur which are not covered in this manual, use
care and good judgement. Contact Customer Support for
assistance and the name of the nearest service dealer.
2.
Before starting the machine, make sure the chipper chute,
feed intake, and cutting chamber are empty and free of all
debris.
Maintenance & Storage
1.
Never tamper with safety devices. Check their proper
operation regularly.
3.
Thoroughly inspect all material to be shredded and remove
any metal, rocks, bottles, cans, or other foreign objects
which could cause personal injury or damage to the
machine.
2.
Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage and repair, if
needed.
4
Section 2 — important Safe operation practiceS
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Before cleaning, repairing, or inspecting, stop the engine
and make certain the impeller and all moving parts have
stopped. Disconnect the spark plug wire and ground it
against the engine to prevent unintended starting.
Notice Regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM), Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
4.
Do not change the engine governor settings or overspeed
the engine. The governor controls the maximum safe
operating speed of the engine.
5.
6.
7.
Maintain or replace safety and instruction labels, as
necessary.
Spark Arrestor
Follow this manual for safe loading, unloading,
transporting, and storage of this machine.
WARNING: This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered,
brushcovered or grass-covered land unless the
engine’s exhaust system is equipped with a spark
arrestor meeting applicable local or state laws (if
any).
Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer, etc.
8.
9.
Allow machine to cool at least 5 minutes before storing.
Always refer to the operator’s manual for proper
instructions on off-season storage.
If a spark arrestor is used, it should be maintained in effective
working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
10. If the fuel tank has to be drained, do this outdoors.
11. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
A spark arrestor for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
12. According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years,
or 60 hours of operation. At the end of the Average Useful
Life have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety
systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Section 2 — important Safe operation practiceS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol
Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running. There are rotating
blades inside
BYSTANDERS
Keep bystanders, pets, and children at least 75 feet from the machine while it is in operation.
Stop machine if anyone enters the area.
WARNING— THROWN DEBRIS
Never operate without the chute deflector properly attached to the machine.
EYE PROTECTION
Always wear safety glasses or safety goggles when operating this machine.
WARNING: Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
6
Section 2 — important Safe operation practiceS
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly & Set-Up
3
Contents of Carton
•
•
•
One Chipper Shredder
One Tow Bar
•
•
One Operator’s Manual
One Bag
•
•
One Engine Operator’s Manual
One Safety Glasses
One Bottle of Oil
Bag
Assembly
To attach the bag:
NOTE: This unit is shipped without gasoline or oil in the engine.
Fill up gasoline and oil as instructed in the accompanying engine
manual BEFORE operating your chipper shredder.
1.
Place the opening of the bag completely over the chute
Chipper Chute (Model Series CS 3310 Only)
For shipping reasons, the unit is crated with its chipper chute in a
raised position. To pivot it downward, proceed as follows:
1.
Pull the spring latch upward.
2.
Gently pivot the chipper chute down until it clicks into the
A
B
Figure 3-2
2.
Position the bag so that the wing knobs which secure the
chute deflector to the impeller housing are completely
covered.
3.
Pull on the draw-strap until the bag is tight around chute
deflector opening.
Figure 3-1
WARNING: Never operate the chipper shredder
with the chipper chute in the raised position. Doing
so may result in property damage or serious injury
to the operator or bystanders.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Tow Bar
To attach the tow bar:
Set-Up
Gas and Oil Fill-Up
Refer to the separate engine owner’s manual for additional
engine information.
1.
Remove the spring pin and clevis pin from the end of the
1.
Add oil provided before starting unit for the first time out
of the box.
2.
Service the engine with gasoline as instructed in the
separate engine owner’s manual.
WARNING: Use extreme care when handling
gasoline. Gasoline is extremely flammable and the
vapors are explosive. Never fuel the machine
indoors or while the engine is hot or running.
Extinguish cigarettes, cigars, pipes and other
sources of ignition.
WARNING: Never fill fuel tank indoors with engine
running or until the engine has been allowed to cool
for at least two minutes after running.
1
Figure 3-3
2.
Insert the tow bar into the receiver.
3.
Reinsert the clevis pin through aligning holes in both the
tow bar and the receiver.
4.
4
2
3
Figure 3-4
8
Section 3 — ASSembly & Set-Up
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Features
4
Hopper
Handle
Spring Latch
Chipper Chute
Recoil Starter
Tow Bar
Receiver
Lock Rod
Model Series CS 3310 Shown
Figure 4-1
Recoil Starter
Chipper Chute
The recoil starter is located on the engine. Pull the recoil starter
to start engine.
Branches up to two inches (model series CS 2210) or three inches
(model series CS 3310) in diameter may be fed into the chipper
chute for chipping.
Engine Controls
See the engine Owner/Operator manual packed with your unit
Hopper
for the location and function of the controls on the engine.
Leaves, twigs, and branches up to 1/2-inch in diameter may be
Spring Latch (Model Series CS 3310 Only)
The spring latch is located on the top of the hopper. It is used to
release or lock the chipper chute in a raised position for storage
IMPORTANT: Never place branches with a diameter greater than
1/2-inch in the hopper. Doing so can result in serious damage to
your unit’s shredder blade, flails or impeller.
Tow Bar
WARNING: Never operate the chipper shredder
with the chipper chute in the raised position. Use
the spring latch to lower the chipper chute into the
operating position before starting the engine.
Use the tow bar to tow the chipper shredder behind a tractor to
a job site.
Handle
Lock Rod (Model Series CS 3310 Only)
The lock rod is located on the chipper chute support. It is used
to release or lock the chipper chute in a lowered position for
operation.
Use the handle when manually transporting the chipper
shredder.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
5
NOTE: If you’re unable to pull the starter rope as a result of
accumulated debris near the impeller, follow instructions
under the heading Cleaning the Reduction Chamber in the
“Maintainenance & Adjustments” section of this manual.
WARNING: The operation of any chipper shredder
can result in foreign objects being thrown into the
eyes, which can damage your eyes severely. Always
wear the safety glasses provided with this unit or
eye shields before chipping or shredding and while
performing any adjustments or repairs.
Chipping
WARNING: Never operate the chipper shredder
without chipper chute lowered into the operating
position.
Starting Engine
Refer to the engine operator’s manual for the starting
instructions.
Branches up to two inches (model series CS 2210) or three
inches (model series CS 3310) in diameter can be fed into the
chipper chute. Observe the following guidelines when chipping
branches:
Shredding
Yard waste such as leaves and pine needles can be placed in
the hopper for shredding. After material has been processed by
the shredder blade and flails, it will be forced out of the chute
deflector, and, if attached, into a debris collection bag.
•
•
•
•
Keep both hands firmly on the branch as you feed it into
the chipper chute.
Observe the following guidelines when shredding yard debris:
Never feed more than one branch into the chipper chute at
a time.
•
Never attempt to shred material other than normal yard
debris (leaves, twigs, pine cones, etc.).
Never feed anything other than branches (or wood) into
the chipper chute.
•
Avoid shredding fibrous plants such as tomato vines until
they are thoroughly dried out. Fresh vines do not shred
well and tend to wrap themselves around the impeller and
flails.
Apply intermittent pressure (force, in short pulses) while
feeding larger branches into the chipper chute, to avoid
bogging or stalling the engine.
•
•
Place reasonable amounts of debris into the hopper at a
time. Do not overload the hopper.
IMPORTANT: Never feed branches with a diameter greater
than two (2) inches (Model Series CS 2210) or three (3)
inches (model series CS 3310) into the chipper chute. Doing
so can result in serious damage to your unit’s chipper
blades, flails or impeller.
Allow the material in the hopper to be drawn into the
blades and shredded before adding additional debris
to the hopper. Failure to due so may result in a clogged
hopper, clogged chute deflector or a stalled engine.
NOTE: For best performance, always operate the unit with
sharp chipper blades. If a noticeable loss in performance is
encountered while chipping branches, the chipper blades
should be replaced.
•
Avoid placing twigs longer than 24 inches into the hopper.
Twigs longer than 24 inches may result in a clogged
hopper.
IMPORTANT: Never place branches with a diameter greater
than 1/2-inch in the hopper. Doing so can result in serious
damage to the unit’s shredder blade, flails or impeller.
Clearing the Hopper
Should the hopper become clogged with debris during
operation, proceed as follows:
1.
Grasp the handle with both hands and gently agitate the
chipper shredder to help loosen debris, drawing it into the
impeller.
If the clog does not clear, proceed as follows:
1.
Stop engine.
2.
Use your hands to remove any debris found near the top of
the hopper.
3.
Use a branch (or other available device, i.e. broomstick) to
dislodge debris located toward the base of the hopper.
4.
Restart engine.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Emptying the Bag
1.
Stop engine.
2.
Squeeze the locking buckle to release the bag’s drawstrap
before loosening it from the chute deflector. See Figure
5-2.
Figure 5-2
3.
Empty the bag and reattach to the chute deflector
opening. Refer to the “Set-Up & Adjustments” section of
this manual.
Section 5 — operation
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance & Adjustments
6
Equipment Care
Maintenance
•
Clean the chipper shredder thoroughly after each use.
General Recommendations
•
Wash bag periodically with water. Allow to dry thoroughly
in shade.
•
Always observe safety rules when performing any
maintenance.
•
If the reduction chamber becomes clogged, remove and
clean as instructed below.
•
The warranty on this chipper shredder does not cover
items that have been subjected to operator abuse or
negligence. To receive full value from warranty, operator
must maintain the equipment as instructed here.
NOTE: Cleaning with a forceful spray of water is not
recommended as it could contaminate the fuel system.
•
•
•
Changing of engine-governed speed will void engine
warranty.
Engine Care
Refer to the Maintenance section of the Engine Operator’s
manual packed with your unit. Read and follow instructions
carefully.
All adjustments should be checked at least once each
season.
Periodically check all fasteners and make sure these are
tight.
•
Check engine oil level before each use as instructed in the
separate engine manual.
•
Clean or replace air cleaner every 25 hours under normal
conditions. Clean every few hours under extremely dusty
conditions. To service the air cleaner, refer to the engine
manual.
WARNING: Always stop engine, disconnect spark
plug, and ground against engine before, cleaning,
lubricating, or performing any type of maintenance
on your machine.
•
•
The spark plug should be cleaned and the gap reset once
a season. Check engine manual for correct plug type and
gap specifications.
Lubrication
1.
2.
3.
Lubricate the chipper chute hinge a with light oil once a
season.
Clean engine regularly with a cloth or brush. Keep the
top of the engine clean to permit proper air circulation.
Remove all grass, dirt, and combustible debris from muffler
area.
Lubricate the pivot points on the chute deflector with light
oil once a season.
Follow the separate engine manual packed with your unit
for engine lubrication instructions.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Remove the hairpin clip from the clevis pin which extends
Remove clevis pin.
Cleaning The Reduction Chamber
WARNING: The impeller’s shredder blade and
chipper blades are sharp. Wear leather work gloves
to protect your hands when cleaning out the
reduction chamber.
4.
5.
the surrounding area by scraping away debris.
Confirm that the spark plug wire is disconnected and away
from spark plug. Pull on the starter rope two-to-three
times to purge any remaining debris from the reduction
chamber.
If the reduction chamber becomes clogged with debris, the
shredder screen can be pivoted upward so that you can clean the
surrounding area. To do so, proceed as follows:
1.
Stop engine, disconnect spark plug, and make certain the
chipper shredder has come to a complete stop.
6.
7.
When the area is cleaned, pivot the shredder screen
downward and re-secure with the clevis pin and hairpin
clip removed earlier.
WARNING: The muffler and surrounding area will
be hot if the engine has been running. Use caution
and protect your hands if working near the muffler.
Reattach the debris collection bag to the chute deflector, if
desired.
2.
If attached, remove debris bag. Remove the two wing
knobs on either side of the chute deflector and pivot the
C
A
B
Figure 6-1
Section 6 — Maintenance & adjuStMentS
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
7
7.
Install a replacement blade (Part No. 742-0544) with the
hardware removed earlier or sharpen.
Blade Care
Chipper Blades
IMPORTANT: When sharpening the blade, protect hands by
using gloves. Follow the original angle of grind and make
sure to remove an equal amount from each blade.
WARNING: The impeller’s chipper blades are
sharp. Wear leather work gloves to protect your
hands.
8.
To replace the other blade, rotate the impeller to expose
the second blade and repeat the steps above.
1.
2.
3.
Stop engine, disconnect spark plug, and make certain the
chipper shredder has come to a complete stop.
NOTE: Make certain blades are reassembled with the sharp
edge outward (toward the chipper chute). Torque hardware
to between 20 ft.-lbs and 25 ft.-lbs.
Pivot the shredder screen upward as instructed under the
heading Cleaning the Reduction Chamber.
Shredder Blade
Remove the chipper chute support brace from the frame
by removing the two hex bolts and saddle washers which
WARNING: The shredder blade is sharp. Wear
leather work gloves to protect your hands.
1.
Stop engine, disconnect spark plug, and make certain that
all moving parts have come to a complete stop.
2.
Remove the two flange nuts (and hex bolts) which secure
the hopper support bracket to the impeller housing. Retain
C
B
A
Model Series CS 3310 Shown
Figure 7-1
4.
Remove the chipper chute by removing three hex nuts and
washers which secure it to the impeller housing. See Figure
7-1B.
5.
6.
Rotate the impeller by hand until one of the two chipper
blades is visible through the impeller housing opening.
Remove the blade by removing the internal hex screws,
lock washers and hex nuts which secure it to the impeller.
Figure 7-2
3.
Pivot the shredder screen upward as instructed under the
heading Cleaning the Reduction Chamber.
NOTE: Use a 3/16” hex key (Allen) wrench on the outside of
the blade and a 1/2” box (or socket) wrench on the inside of
the impeller. Hold the Allen wrench stationary and rotate
the box (or socket) wrench to loosen the nut.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Remove six flange nuts which secure hopper inlet guide to
7.
Remove the two internal hex screws, hex lock nuts, and
lock washers which secure the shredder blade to the
NOTE: Use a 3/16” hex key (Allen) wrench on the outside
of the shredder blade and a 1/2” box (or socket) wrench
on the inside of the shredder blade. Hold the Allen wrench
stationary and rotate the box (or socket) wrench to loosen
the nut.
8.
Remove the hex bolt, lock washer, and flat washer to
IMPORTANT: If sharpening the blade for reuse, follow
the original angle of grind as a guide. Make certain each
cutting edge receives an equal amount of grinding to
prevent an unbalanced blade. Remove metal from the
heavy side until it is balanced evenly.
B
C
IMPORTANT: When reassembling the blade, tighten center
bolt to between 45 ft.-lbs and 58 ft.-lbs and the two out
bolts to between 20 ft.-lbs and 25 ft.-lbs.
A
Off-Season Storage
•
Allow the unit to run and clear out all debris for a short
time before shutting the unit down before storage.
Figure 7-3
•
When storing the chipper shredder in an unventilated or
metal storage shed, care should be taken to rustproof the
non-painted surfaces. Using a light oil or silicone, coat the
equipment, especially any springs, bearings, and cables.
5.
6.
Carefully separate the hopper assembly from the impeller
housing and set it aside.
Insert a piece of wood into the chute deflector opening to
stabilize the impeller and prevent it from rotating when
removing the shredder blade.
•
•
•
Remove all dirt from exterior of engine and equipment.
Follow lubrication recommendations.
Refer to engine manual for correct engine storage
instructions.
•
Store equipment in a clean, dry area. Do not store in an
area where equipment is present that may use a pilot light
or has a component that can create a spark.
Section 7 — Service
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Problem
Cause
Remedy
Engine Fails to start
1. Throttle lever not in correct starting position.
1. Move throttle lever to FAST or START
position.
2. Spark plug wire disconnected.
3. Choke not in CHOKE position (if equipped).
4. Fuel tank empty or stale fuel.
5. Engine not primed (if equipped).
6. Faulty spark plug.
2. Connect wire to spark plug.
3. Move choke lever to CHOKE position.
4. Fill tank with clean, fresh gasoline.
5. Prime engine as instructed in Engine Manual.
6. Clean, adjust gap, or replace.
7. Clean fuel line.
7. Blocked fuel line.
8. Engine flooded.
8. Wait a few minutes to restart, but do not
prime.
Engine runs erratic
1. Spark plug boot loose.
1. Connect and tighten spark plug boot.
2. Move choke lever to OFF position.
2. Unit running on CHOKE (if equipped).
3. Blocked fuel line or stale fuel.
3. Clean fuel line; fill tank with clean, fresh
gasoline.
4. Low engine RPM.
4. Always run engine at full throttle.
5. Drain fuel tank. Refill with fresh fuel.
6. Refer to engine manual.
5. Water or dirt in fuel system.
6. Dirty air cleaner.
7. Carburetor out of adjustment.
7. See authorized service dealer.
Engine overheats
1. Engine oil level low.
1. Fill crankcase with proper oil.
2. Refer to engine manual.
2. Dirty air cleaner.
3. Carburetor not adjusted properly.
3. See authorized service dealer.
Occasional skips
(hesitates) at
high speed
1. Spark plug gap too close.
1. Remove spark plug and adjust gap to .030”.
2. Carburetor idle mixture adjustment
improperly set.
2. See authorized service dealer.
Excessive Vibration
1. Loose parts or damaged impeller.
1. Discharge area clogged.
2. See authorized service dealer.
Unit does not discharge
1. Stop engine immediately and disconnect
spark plug wire. Clean flail screen and inside
of discharge opening.
2. Foreign object lodged in impeller.
2. Stop engine and disconnect spark plug wire.
Remove lodged object.
3. Low engine RPM.
3. Always run engine at full throttle.
1. Always run engine at full throttle.
Rate of discharge slows
considerably or composition
of discharged material
changes
1. Low engine RPM.
2. Chipper blade dull.
2. Replace chipper blade or see your authorized
service dealer.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts
9
Component
Part Number and Description
942-04050
Shredder Blade
942-0544B
Chipper Blade
719-04308
Flail Blade (3 total)
634-04627
10 x 4.0 Pneumatic Wheel
Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
10
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 10 — noteS
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY FOR SNOW THROWERS, LOG SPLITTERS
CHIPPER-SHREDDERS, CHIPPER-SHREDDER VACUUMS AND JET SWEEPS
The limited warranty set forth below is given by Cub Cadet LLC
with respect to new merchandise purchased and used in the United
States, its possessions and territories, and by MTD Products Limited
with respect to new merchandise purchased and used in Canada
and/or its territories and possessions.
b.
Log splitter pumps, valves, and cylinders have a separate one
year warranty.
c.
Cub Cadet does not extend any warranty for products sold
or exported outside of the United States and/or Canada, and
their respective possessions and territories, except those
sold through Cub Cadet’s authorized channels of export
distribution.
This warranty is in addition to any applicable emissions warranty
provided with your product.
For non-commercial use: Cub Cadet warrants this product
(excluding Normal Wear Parts, as described below) against defects
in material and workmanship for a period of three (3) years from the
date of original retail purchase or lease.
d.
e.
Replacement parts that are not genuine Cub Cadet parts.
Service completed by someone other than an authorized
service dealer.
f.
Transportation charges and service calls.
For commercial uses and applications: Cub Cadet warrants this
product (excluding Normal Wear Parts, as described below) against
defects in material and workmanship for a period of one (1) year
from the date of original retail purchase or lease.
No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose, applies
after the applicable period of express written warranty above
as to the parts as identified. No other express warranty,
whether written or oral, except as mentioned above, given by
any person or entity, including a dealer or retailer, with respect
to any product, shall bind Cub Cadet. During the period of the
warranty, the exclusive remedy is repair or replacement of the
product as set forth above.
“Cub Cadet” will, at its option, repair or replace, free of charge,
any part found to be defective in materials or workmanship.
This limited warranty shall only apply if this product has been
operated and maintained in accordance with the Operator’s
Manual furnished with the product, and has not been subject to
misuse, abuse, neglect, accident, improper maintenance, alteration,
vandalism, theft, fire, water, or damage because of other peril or
natural disaster. Damage resulting from the installation or use
of any part, accessory or attachment not approved by Cub Cadet
for use with the product(s) covered by this manual will void your
warranty as to any resulting damage.
The provisions as set forth in this warranty provide the sole
and exclusive remedy arising from the sale. Cub Cadet shall
not be liable for incidental or consequential loss or damage
including, without limitation, expenses incurred for substitute
or replacement lawn care services or for rental expenses to
temporarily replace a warranted product.
Normal Wear Parts are warranted to be free from defects in material
and workmanship for a period of thirty (30) days from the date of
purchase. Normal wear parts include, but are not limited to items
such as: belts, skid shoes, shave plates, blades, debris collection
bags, wheels and tires.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply
to you.
In no event shall recovery of any kind be greater than the amount
of the purchase price of the product sold. Alteration of safety
features of the product shall void this warranty. You assume
the risk and liability for loss, damage, or injury to you and your
property and/or to others and their property arising out of the
misuse or inability to use the product.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service dealer.
To locate the dealer in your area:
In the U.S.A.
To locate the dealer in your area, check your Yellow Pages, or
contact Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-
0019, or call 1-877-282-8684, or log on to our Web site at www.
cubcadet.com.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased as a
gift.
In Canada
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have
other rights that vary in different jurisdictions.
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call
This limited warranty does not provide coverage in the following
cases:
IMPORTANT: Owner must present Original Proof of Purchase to
obtain warranty coverage.
a.
Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior
finish due to use or exposure.
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
GDOC-100160 REV. B
Download from Www.Somanuals.com. All Manuals Search And Download.
|