Crosley®
DRYER
Owner's Guide
SECADORA
Manual del Usuario
P/N 134856900 (0701)
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS
DRYERS:
ELECTRIC DRYERS:
Do ot under any
Avoid fire
hazard or electrical shock.
Donotuseanadaptorplug
or extension cord or
remove grounding prong
fromelectricalpowercord.
Failure to follow this
warning can cause serious
injury, fire or death.
circumstances cut,
14-30R
remove, or bypass
the grounding
prong from this
Grounding
type wall
receptacle
DRYER
plug.
FUSED 30 AMP
120/240V OR
Power supply cord
with 3-prong
grounding plug
120/208V WALL
RECEPTACLE
DRYER SERVICE CORD
g
CORRECT Use this way ONLY
CORRECT Use this way ONLY
Important Safety Instructions
Read all instructions before using this dryer.
SAVE THESE INSTRUCTIONS
You can be killed or seriously injured if you don't follow these Important Safety Instructions:
• Failure to comply with these warnings could result in serious personal injuries.
PreventFire
• Do not dry items that have been previously cleaned in, soaked in, or spotted with gasoline, cleaning solvents, kerosene, waxes,
etc. Do not store these items on or near the dryer. These substances give off vapors that could ignite or explode.
•Donotdryarticlescontainingrubber, plasticorsimilarmaterialssuchas bras, galoshes, bathmats, rugs, bibs, babypants, plastic
bags and pillows that may melt or burn. Some rubber materials, when heated, can under certain circumstances produce fire by
spontaneouscombustion.
• Clean the lint screen before or after each load. The interior of the dryer, lint screen housing and exhaust duct should be cleaned
approximately every 18 months by qualified service personnel. An excessive amount of lint build-up in these areas could result in
inefficient drying and possible fire. See Care and Cleaning.
• Do not operate the dryer if the lint screen is blocked, damaged or missing. Fire hazard, overheating and damage to fabrics can
occur. If your dryer has a drying rack, always replace the lint screen when finished using the drying rack.
• -RiskofFire-Aclothesdryerproducescombustiblelint. Thedryermustbeconnectedtoanexhaustoutdoors. Regularlyinspect
theoutdoorexhaustopeningandremoveanyaccumulationoflintaroundtheoutdoorexhaustopeningandinthesurroundingarea.
• Do not obstruct the flow of ventilating air. Do not stack or place laundry or throw rugs against the front or back of the dryer.
• Do not spray any type of aerosol into, on or near dryer at any time.
•Donotusefabricsoftenersorproductstoeliminatestaticunlessrecommendedbythemanufacturerofthefabricsoftenerorproduct.
•Donotplaceitemsexposedtocookingoilsinyourdryer. Itemscontaminatedwithcookingoilsmaycontributetoachemicalreaction
that could cause a load to catch fire.
• Failure to comply with these warnings could result in fire, explosion, serious bodily injury and/or damage to the rubber or plastic
parts of the dryer.
ProtectChildren
• Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.
As children grow, teach them the proper, safe use of all appliances.
• Destroy the carton, plastic bag and other packing materials after the dryer is unpacked. Children might use them for play. Cartons
covered with rugs, bedspreads or plastic sheets can become airtight chambers.
• Keep laundry products out of children's reach. To prevent personal injury, observe all warnings on product labels.
• Before the dryer is removed from service or discarded, remove the dryer door to prevent accidental entrapment.
• Failure to comply with these warnings could result in serious personal injuries.
PreventInjury
• To prevent shock hazard and assure stability during operation, the dryer must be installed and electrically grounded by a qualified
service person in accordance with local codes. Installation instructions are packed in the dryer for the installer's reference. Refer to
INSTALLATION INSTRUCTIONS for detailed grounding procedures. If the dryer is moved to a new location, have it checked and
reinstalled by a qualified service person.
•Topreventpersonalinjuryordamagetothedryer,theelectricalpowercordofagasdryermustbepluggedintoaproperlygrounded
and polarized 3-prong outlet. The third grounding prong must never be removed. Never ground the dryer to a gas pipe.
Do not use an extension cord or an adaptor plug.
• ALWAYS disconnect the dryer from the electrical supply before attempting any service or cleaning. Failure to do so can result
in electrical shock or injury.
• Do not use any type spray cleanser when cleaning dryer interior. Hazardous fumes or electrical shock could occur.
• To prevent injury, do not reach into the dryer if the drum is moving. Wait until the dryer has stopped completely before reaching
into the drum.
• To prevent injury and damage to the dryer:
-
All repairs and servicing must be performed by an authorized servicer unless specifically recommended in this Owner's
Guide. Use only authorized factory parts.
-
-
Do not tamper with controls.
Do not install or store the dryer where it will be exposed to the weather.
• A thermal limiter switch automatically turns off the motor in the unlikely event of an overheated situation (electric dryers only). A
service technician must replace the thermal limiter switch after correcting the fault.
• Failure to comply with these warnings could result in serious personal injuries.
Printed in U.S.A.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
• Follow the guidelines below for preparing the load for drying.
• Read the Operating Instructions card for operating your specific model.
• Always read and follow fabric care labels and laundry product labels.
Drying Procedures
To reduce the risk of fire, electrical shock, or injury to persons, read
Important Safety Instructions before operating this dryer.
1. Prepare items for drying.
•
•
Dry items of similar fabric, weight and construction in the same load.
Separate dark items from light-colored items. Separate items that shed lint
from those that attract lint. If an item sheds lint, turn it inside out.
Besurebuckles,buttonsandtrimareheatproofandwon'tdamagethedrum
finish.Closezippers,fastenhooksandVelcro®-likefasteners.Tiestringsand
sashes to prevent snagging and tangling.
•
•
•
If possible, turn pockets inside out for even drying.
Follow fabric care label instructions.
Check for stains which may not have been removed in washing. Dryer heat
may permanently set some stains. Repeat stain removal process before
drying.
•
Place small items in a mesh bag to prevent tangling and for easy removal.
2. Check that lint screen is clean and in place.
3. Load the dryer.
•
•
•
•
•
Theaverageloadwillfillthedrum1/3to1/2full.Itemsneedroomtotumble
freely for even drying and less wrinkling. Do not overload dryer.
Whendryinglargeitems,dryonly2or3atatime.Fillouttheloadwithsmall
and medium sized items.
For delicate or very small loads, add 2 lint-free towels for better drying, less
wrinkling, and to prevent grease stains caused by fabric softener sheets.
Donotoverdryitems.Overdryingcancausewrinkling,shrinkage,harshness,
and a build-up of static electricity, which can produce more lint.
If desired, add a dryer fabric softener sheet.
Place small items in a mesh bag.
4. Close the dryer door and select the cycle, temperature, dryness level
and options desired. See Operating Instructions for your specific model
information.
5. Press START to begin the cycle.
•
To add or remove items when the dryer is running open the door. The
dryer will stop when the door is opened. Allow the drum to come to a
complete stop before reaching inside.
•
Close the door and press Start to resume the cycle.
6. When the cycle ends, remove items immediately and hang or fold.
Fill dryer drum 1/3 to 1/2 full.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
End of Cycle Signal
A signal will sound at the end of the cycle and periodically during Extended Tumble
Features
at the volume level selected. (some models)
Drum Light (some models)
Adrumlightwillcomeonwheneverthedoorisopenedtoilluminatethedryerdrum
during loading and unloading. Closing the door turns off the light.
ReversibleDryerDoor
Your dryer is equipped with a reversible door. The door can be hinged on the right
or left side. Refer to the INSTALLATION INSTRUCTIONS for directions on changing
the door.
Drying Rack (some models)
Use the drying rack to dry items which should not be tumble dried.
1. Open the dryer door and remove the lint screen.
2. Insert drying rack into the dryer drum. Place the front bar under the lip of the
lint screen opening.
3. Place items to be dried on top of the rack. Weight should not exceed 10 lbs.
Leavespacebetweenitems, butdonotletitemshangoverthesidesorthrough
the grids. Do not tumble other items when using the drying rack.
4. Select Timed Dry. Use only the Air Fluff/No Heat option for items containing
plastic, foam rubber, rubber-like materials, feathers or down.
5. When items are dry, remove the rack and replace the lint screen. If lint screen
is not in place, tumbling items could enter the exhaust system and cause
damage to the dryer.
Place the front bar under
the lip of the lint screen opening.
Toreduceriskoffireorseriousinjurytopersonsorproperty,comply
with the basic warnings listed in Important Safety Instructions and those listed
below.
Care and Cleaning
•
•
Before cleaning the dryer interior, unplug the electrical power cord to avoid
electrical shock hazards.
Do not use any type spray cleanser when cleaning dryer interior. Hazardous
fumes or electrical shock could occur.
Inside
• Cleanthelintscreenaftereveryload.Lintbuild-upinthescreenrestrictsairflow,
whichcauseslongerdryingtimes.Thescreenislocatedatthebottomofthedoor
opening.Removebypullingstraightup.Removethelintandreplacethescreen.
CAUTION - Risk of Fire - A clothes dryer produces combustible lint. The dryer
must be connected to an exhaust outdoors. Regularly inspect the outdoor
exhaust opening and remove any accumulation of lint around the outdoor
exhaust opening and in the surrounding area.
•
Occasionallyawaxybuild-upmayformonthelintscreenfromusingdryer-added
fabric softener sheets. To remove this build-up, wash the lint screen in warm,
soapy water. Dry thoroughly and replace. Do not operate the dryer without the
lint screen in place.
•
•
Ifthedryerdrumbecomesstainedfromnoncolorfastfabrics,cleanthedrumwith
a damp cloth and a mild liquid household cleanser. Remove cleanser residue
before drying the next load.
Every 18 months an authorized servicer should clean the dryer cabinet interior
and exhaust duct. These areas can collect lint and dust over time. An excessive
amountoflintbuild-upcouldresultininefficientdryingandpossiblefirehazard.
5
Clean lint screen after every load.
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning (continued)
Outside
•
•
•
•
Clean the cabinet with mild soap and water. Never use harsh, gritty or
abrasivecleansers.
If the cabinet becomes stained, clean with diluted chlorine bleach [1/2 cup
(120 ml) in 1 quart (.95 liter) water]. Rinse several times with clear water.
Removeglueresiduefromtapeorlabelswithamixtureofwarmwaterandmild
detergent. Or, touch residue with the sticky side of the tape or label.
Before moving the dryer, place a strip of cardboard or thin fiberboard under
the front leveling legs to prevent damage to floor.
Do not store or place laundry products
on top of dryer at any time. They can
damage the finish or controls.
Common Drying Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage.
For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.
PROBLEM
POSSIBLECAUSES
SOLUTIONS
PREVENTIVEMEASURES
Greasy, oily
stains
• Fabric softener sheet.
• Add a few bath towels to small loads for
propertumbling.
• Some "silk-like" fabrics should be air
dried.
• Rubfabricsoftenerstainswithbarsoap.
Rinse and rewash.
• Use proper drying temperature.
• Place fabric softener sheet on top of load
before starting the dryer.
Lint
• Do not overload dryer.
• Use fabric softener in washer or dryer to
reduce static electricity.
• Remove items when they are slightly
damp to avoid overdrying.
• Check that lint screen is clean and in
place.
• Overloading.
• Overdrying causes static
electricity.
• Lint screen not clean
when cycle began.
• Lintisattachedto"pills."
• Reduceloadsizeandrewashusingliquid
fabric softener in the final rinse.
• Or, add a fabric softener sheet and
tumble without heat.
• Use lint brush or roller to remove lint.
Pilling
• Use fabric softener to lubricate fibers.
• When ironing, use spray starch or fabric
finish on collars and cuffs.
• Pilling is normal with
syntheticandpermanent
press fabrics. This is due
to abrasion from normal
wear.
• Usealintbrushorshavertoremovepills.
• Irreversiblecondition.
(Fibers break
off, ball up
and cling to
fabric.)
• Turn items inside out to reduce abrasion.
Shrinking
Wrinkling
• Follow fabric care label directions.
• Ifshrinkingisaconcern,checkloadoften.
• Remove items while slightly damp and
hang or lay flat to complete drying.
• Block knits into shape.
• Overdrying.
• Do not overload dryer.
• Remove items as soon as cycle ends.
• Overloading.
• Leaving items in dryer
after cycle ends.
• Reduceloadsizeandtumbleatmedium
or low heat for 5-10 minutes.
• Remove items immediately. Hang or
fold.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before calling for service, review this list. It may save both time and expense. The list includes
common occurrences that are not the result of defective workmanship or materials in this dryer.
Avoid Service
Checklist
OCCURRENCE
POSSIBLE CAUSE
SOLUTION
Electrical power cord is not securely plugged
in or plug may be loose.
Make sure the plug fits tightly in wall outlet.
Dryer does not start.
House fuse blown or circuit breaker tripped.
Reset circuit breaker or replace fuse.
Make sure electrical line is not overloaded and the dryer is on
a separate circuit.
Thermal limiter tripped.
Call authorized service person for replacement.
Replace fuse.
There are 2 house fuses in the dryer circuit. If
1 of the 2 fuses is blown, the drum may turn
but the heater will not operate.
Dryer runs but won't heat.
Gas supply valve is not open (gas models).
Check to make sure supply valve is open. See INSTALLATION
INSTRUCTIONS for procedure.
Dryer does not have anough air supply to
support the burner flame (gas models).
See INSTALLATION INSTRUCTIONS.
LP gas supply tank is empty or there has been
a utility interruption of natural gas (gas
models).
Refill or replace tank.
Dryer should heat when utility service is restored.
Lint screen is clogged with lint.
Makesurealllinthasbeenremovedfromthedryerlintscreen
before starting each cycle.
Drying cycle takes too long,
outsideofthedryerfeelstoo
hot or smells hot.
Exhaust duct requirements have not been
met.
Exhaust duct must be at least 4 inches in diameter and made
of rigid or flexible metal.
When in place, the duct must have no more than two 90°
bends and must not exceed length listed in INSTALLATION
INSTRUCTIONS.
Electricdryerisconnectedtoa208voltcircuit.
Drying procedures have not been followed.
Drying time will be 20% longer than drying on a 240 volt
circuit.
See Drying Procedures .
Outside exhaust hood or exhaust duct may
be clogged or restricted.
Clean out any obstruction.
High humidity.
Use a dehumidifier near the dryer.
Do not overload. See Drying Procedures .
Remove items as soon as cycle ends.
See Drying Procedures .
Dryer is overloaded.
Excessivewrinkling.
Items left in dryer too long.
Insufficient sorting of items.
Drying temperature too high.
Follow fabric care label instructions.
Foreign objects such as coins, pins, clips or
buttons are inside the dryer.
Always remove foreign objects from pockets before
laundering. Remove objects from drum and restart dryer.
Scratchingorchippingofthe
drumfinish.
Permanently attached items such as belt
buckles, zippers and fasteners may be hitting
the inside of the drum.
It may be necessary to baste a scrap of material securely
around ornaments before drying to prevent scratching and
damage to the dryer.
Drumdamagecausedbyforeignobjectsorpermanently
attached items is not covered by the warranty.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CROSLEY® WARRANTY
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay
allcostsforrepairingorreplacinganypartsofthisappliancethatprovetobedefectiveinmaterialsorworkmanshipwhensuch
appliance is installed, used and maintained inaccordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not
in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,
handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to
floors,cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other
than genuine Electrolux parts or parts obtained from persons other than authorized service companies;
or external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMEROFIMPLIEDWARRANTIES;LIMITATIONOFREMEDIES
CUSTOMER’SSOLEANDEXCLUSIVEREMEDYUNDERTHISLIMITEDWARRANTYSHALLBE
PRODUCTREPAIRORREPLACEMENTASPROVIDEDHEREIN. CLAIMSBASEDONIMPLIED
WARRANTIES,INCLUDINGWARRANTIESOFMERCHANTABILITYORFITNESSFORAPARTICULAR
PURPOSE, ARELIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT
LESSTHANONEYEAR.ELECTROLUXSHALLNOTBELIABLEFORCONSEQUENTIALORINCIDENTAL
DAMAGESSUCHASPROPERTYDAMAGEANDINCIDENTALEXPENSESRESULTINGFROMANY
BREACHOFTHISWRITTENLIMITEDWARRANTYORANYIMPLIEDWARRANTY.SOMESTATESAND
PROVINCESDONOTALLOWTHEEXCLUSIONORLIMITATIONOFINCIDENTALORCONSEQUENTIAL
DAMAGES,ORLIMITATIONSONTHEDURATIONOFIMPLIEDWARRANTIES,SOTHESELIMITATIONS
OREXCLUSIONSMAYNOTAPPLYTOYOU.THISWRITTENWARRANTYGIVESYOUSPECIFICLEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty
periodshould service be required. If service is performed, it is in your best interest to obtain and keep all
receipts.Service under this warranty must be obtained by contacting Electrolux at the addresses or
phonenumbersbelow.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
NorthAmerica,adivisionof ElectroluxHomeProducts,Inc.InCanada,yourapplianceiswarrantedbyElectroluxCanadaCorp.
Electroluxauthorizesnopersontochangeoraddtoanyobligationsunderthiswarranty.Obligationsforserviceandpartsunder
thiswarrantymustbeperformedbyElectroluxoranauthorizedservicecompany.Productfeaturesorspecificationsasdescribed
or illustrated are subject to change without notice.
Replacement parts
If you need to order replacement parts, we recommend that you only use the factory specified parts. These parts will fit right
and work right because they are made with the same precision used to build every new Crosley ® appliance.
To locate factory specified replacement parts in you area call:
USA, 1-800-944-9044, or your nearest designated service center. In Canada call 1-800-668-4606.
For information on how to contact Crosley Corporation, please see page 2 of this document.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|