TM
ELITE EVANSTON 8 TENT
MODEL 2000004674
9. Attach frame clips along edges of tent to
Fig. 3
Before you begin
the black & grey Main Poles. (Fig. 3)
Read all instructions before set up.
•
Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines.
Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
Secure with all stakes and guylines provided to prevent property damage
or personal injury.
10. Stretch tent until taut, then secure metal loops
located on both sides and four corners of tent with
stakes. (Fig. 4)
•
•
•
•
For best results in windy conditions, position narrow end of tent into the wind.
Enlist the help of at least one other person to assist you when it is time to
assemble the tent.
Fig. 4
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic tips); then
insert through zippered vertical pole sleeve on hinged side of door. (Fig. 5)
2. Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to
form a slight bow, then insert other tip of pole into top hinge. Zip up verti-
cal pole sleeve. (Fig. 6 & 7)
3. Assemble Door Pole (longer black pole with plastic cap tips); then insert
into zippered pole sleeve at top of door. (Fig. 8)
4. Insert end of Door Pole into top hinge plate, apply pressure to form a bow,
then insert other tip of pole into the bottom hinge. (Fig. 9)
Pole Descriptions
Pole
Pole
Pole
Description
Qty. Dia.
Repair Kit Replacement Kit
Main Pole, black
Main Pole, grey
2
1
1
1
11mm 5010000539
11mm 5010000539
11mm 5010000539
7.9mm 5010000569
5010000549
5010000549
5010000549
5010000568
Rainfly Pole, grey, long
Awning Pole, black, short
Vertical Door Pole, black,
short w/plastic tips
Door Pole, black,
long w/plastic tips
1
1
6.3mm 5010000543
6.3mm 5010000543
5010000545
5010000545
5. Zip up pole sleeve to enclose Door Pole. (Fig. 10)
Self-Rolling Window Spring Descriptions
Fig. 5
Fig. 6
Fig. 7
Vertical Pole
Sleeve
Color Code Description
Qty.
Length Replacement Part No.
Green
Orange
1
2
610mm
670mm
5010000627
5010000628
Door Hinge
CAUTION: “Springs” may have sharp edges. Handle with care to avoid injury.
Keep out of reach of children.
To Set Up Tent
Fig. 9
Fig. 8
1. Unfold tent and spread out on a clean, level surface with the door facing
the desired direction. (Fig. 1)
TToopp
DDoooorr
Pole
Pole
2. Assemble all poles by interlocking the shock-corded, sections together.
3. Insert black Main Poles through the black trimmed sleeves on top of tent
forming an X”.
4. Insert grey Main Pole through grey trimmed sleeve, in front of tent. Make
sure grey Main Poles overlap the black Main Poles. (Fig. 1)
HHiinnggee
Fig. 10
Sleeve
Sleeve
To Attach Rainfly
1. Drape Rainfly over tent with dark blue vestibule flaps located at the front
of the tent. (Fig 11).
NOTE: Hook and loop fasteners, located on seams of underside of Rainfly,
should be centered over black & grey Main Poles.
2. Insert the long, black, Rainfly Pole with through sleeve in underside of
Rainfly above front door of tent. (Fig. 11)
Sleeves with Black Trim
Fig. 1
Grey, Shock-
Sleeve with
Grey Trim
corded Main Pole
Sleeve with Grey Trim
Door
Rainfly
Front of Tent
Black, Shock-corded Main Poles
Grey, Shock-corded
Rainfly Pole
5. Insert end of each black Main Pole into pins located in the corners of the
tent. (Fig. 2 & 2A)
6. Go to opposite end of each black Main Pole and gradually apply pressure
to each forming arches. Insert the pin into each pole end at the corners of
tent. (Fig. 2 & 2A)
Door
7. Insert end of the grey Main Pole into pin located on the sides of the tent.
(Fig. 2 & 2B)
Front of Tent
Fig. 11
Vestibule Flaps
8. Go to opposite end of the grey Main Pole and gradually apply pressure to
form an arch. Insert the pin into pole end at the side of tent.
(Fig. 2 & 2B)
3. Insert short, black, thin Awning Pole through sleeve in underside of Rainfly
above window at back of tent. (Fig. 12)
4. Insert metal tip into grommet on tent seam at back of tent (Fig. 13). Go to
opposite end of Awning Pole and gradually apply pressure to pole forming
an arch; then insert metal tip into grommet.
2A
Rainfly Sleeve
Awning Pole
2B
Grommet
Door
Awning
Pole
Back of Tent
Fig. 13
Fig. 12
(continued on other side)
Front of Tent
Fig. 2
Download from Www.Somanuals.com. All Manuals Search And Download.
|