TM
OASIS CABIN TENT
MODEL 2000000583
6. Snap hook at top of tent onto metal loop
Before you begin
on bottom of Hub. (Fig. 6)
Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
Fig. 6
7. Insert curved end of four Short
Leg Poles into the four Long
Ridge Poles on top of tent.
(Fig. 7)
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
NOTE: Make sure tab on each Long
Ridge Pole locks into slot on
each Short Leg Pole.
Parts and Components
Description
Part Number
Hub (1)
Short Ridge Pole (2)
Long Leg Pole (2)
Short Leg Pole (4)
Long Ridge Pole (4)
Awning Pole (2)
Rainfly (1)
5010000120
5010000121
5010000122
5010000123
5010000124
5010000125
5010000126
Fig. 7
8. Insert curved end of two Long Leg Poles (with dots) into the
Short Ridge Poles at front & back of tent. (Fig. 8)
NOTE: Make sure tab on each Short Ridge Pole locks into slot
on each Long Leg Pole.
Long Leg Pole (with Dots)
Short Leg Poles
Short Leg Poles
Short Ridge Poles (2)
Hub (1)
Long Leg Poles (2)
Short Leg
Poles (4)
(Front of Tent)
Long Leg Pole
(with Dots)
Fig. 8
Long Ridge
Poles (4)
Awning Poles (2)
9. Raise tent by assembling shock-corded sections of each
Long and Short Leg Pole and inserting into curved ends of
To Set Up Tent
Leg Poles. (Fig. 9)
10. Insert pin on loop at
each corner and the
front and back of tent
into all six Leg Poles.
(Fig. 10)
Fig. 10
Fig. 9
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip doors. (Fig. 1)
Fig. 1
Pin & Loop on web tent strap
Doors
11. Locate both plastic hooks at each corner,
and front and back of tent, then snap
onto Leg Poles to attach. (Fig. 11)
2. Insert the two Short Ridge Poles (with sticker dots) into the
sleeves (perpendicular to door) on top of tent. (Fig. 2)
3. Assemble four, shock-
4 Long Ridge Poles
Fig. 11
corded, Long Ridge
Poles and insert into
the four diagonal corner
sleeves. (Fig. 2)
12. Drive stakes through rings, located on
four corners and front and back of tent,
at an angle for better anchoring.
(Fig. 12)
Fig. 12
2 Short Ridge Poles with Dots
Fig. 2
To Attach Rainfly
1. Drape Rainfly over
tent. Make sure
Rainfly
4. Insert end of first Short Ridge Pole (with
Hub
Short Ridge
Pole with
Dot
dot) into flange with a dot on Hub (Fig. 3).
Repeat for remaining Short Ridge Pole on
opposite flange of Hub with a dot.
seams on Rainfly
are facing down
with web pockets
and long straps
centered over doors
& back of tent.
NOTE: When installed properly, the loop on
the bottom of the Hub will be parallel
two Short Ridge Poles.
Long Strap
Fig. 3
5. Insert four remaining Long Ridge Poles into Hub. (Fig. 4)
Fig. 13
NOTE: Make sure tab on each
(Fig. 13)
pole locks into slot on bottom
2. Locate and wrap hook and
loop fasteners, on underside of
Rainfly, and wrap around the
Leg Poles to secure. (Fig. 14)
Hook and Loop
Fastener
of Hub.
(Fig. 5)
Hub
Tab
Locked
Tab
Slot
Fig. 14
Tab on
Fig. 4
Fig. 5
Pole
(continued on other side)
Download from Www.Somanuals.com. All Manuals Search And Download.
|